Corner Guide Pin and Socket Kits for 104

advertisement
4897:)9/54 !.++9
4897:)9/54 !.++9
408-7121
$ 408-7121
+; Corner Guide Pin and Socket Kits for
104-Position M Series Connectors With Center Fastener
$ Corner Guide Pin and Socket Kits for
104-Position M Series Connectors With Center Fastener
CORNER GUIDE KIT
PIN
+; CORNER GUIDE KIT
SOCKET
PIN
SOCKET
% &
% &
% &
% &
% &
% &
% &
?
% &
Figure 1
?
Figure 1
1. INTRODUCTION
1. INTRODUCTION
The corner guide pin and socket kits listed in Figure 1 are used to
align connectors (plug and receptacle) during mating. The kits can
also be used for keying connectors to provide proper mating.
The corner guide pin and socket kits listed in Figure 1 are used to
align connectors (plug and receptacle) during mating. The kits can
also be used for keying connectors to provide proper mating.
Reasons for reissue of this instruction sheet are provided in
Section 4, REVISION SUMMARY.
Reasons for reissue of this instruction sheet are provided in
Section 4, REVISION SUMMARY.
2. DESCRIPTION
2. DESCRIPTION
Each kit consists of a guide pin or socket, lock washer, and 6–32 hex
nut. Some kits include a spacer. The hardware is designed to be
used in the mounting holes of housings having a minimum of 2 holes.
Each kit consists of a guide pin or socket, lock washer, and 6–32 hex
nut. Some kits include a spacer. The hardware is designed to be
used in the mounting holes of housings having a minimum of 2 holes.
Nut Driver 811262–2 can be used to secure the hardware to the
connector.
Nut Driver 811262–2 can be used to secure the hardware to the
connector.
3. INSTALLATION
3. INSTALLATION
+,+7 95 /-:7+ 1. Insert the threaded end of the guide pin or socket into the front
of the appropriate mounting hole of the connector and, if present,
through the panel.
NOTE
Install the guide pin onto one mating connector, and the guide socket
i
guide pins (one in each diagonal mounting hole) into one connector.
onto the other mating connector; except for Kit 201540-[ ], install two
E
"=)5 2+)9754/)8 57657'9/54 '77/8(:7- 22 49+74'9/54'2
/-.98
+8+7;+*
" 25-5 '4* "=)5 2+)9754/)8 '7+ 97'*+3'718
1 5, +,+7 95 /-:7+ 1. Insert the threaded end of the guide pin or socket into the front
of the appropriate mounting hole of the connector and, if present,
through the panel.
NOTE
Install the guide pin onto one mating connector, and the guide socket
i
guide pins (one in each diagonal mounting hole) into one connector.
onto the other mating connector; except for Kit 201540-[ ], install two
E
"=)5 2+)9754/)8 57657'9/54 '77/8(:7- 22 49+74'9/54'2
/-.98
+8+7;+*
" 25-5 '4* "=)5 2+)9754/)8 '7+ 97'*+3'718
1 5, "7'*+3'71 9.+7 675*:)98 25-58 '4* )536'4= 4'3+8 :8+* '7+ 9.+ 6756+79= 5, 9.+/7 7+86+)9/;+ 5<4+78
"7'*+3'71 9.+7 675*:)98 25-58 '4* )536'4= 4'3+8 :8+* '7+ 9.+ 6756+79= 5, 9.+/7 7+86+)9/;+ 5<4+78
" !!!" "
" !!!" "
#" " "./8 )5497522+* *5):3+49 /8 8:(0+)9 95 ).'4-+
57 2'9+89 7+;/8/54 '4*
+-/54'2 :8953+7 !+7;/)+ ;/8/9 5:7 <+(8/9+ '9
#" " +-/54'2 :8953+7 !+7;/)+ ;/8/9 5:7 <+(8/9+ '9
www.tycoelectronics.com
"./8 )5497522+* *5):3+49 /8 8:(0+)9 95 ).'4-+
www.tycoelectronics.com
57 2'9+89 7+;/8/54 '4*
Corner Guide Pin and Socket Kits for
104-Position M Series Connectors With Center Fastener
408-7121
Corner Guide Pin and Socket Kits for
104-Position M Series Connectors With Center Fastener
408-7121
2. If the connector is not panel–mounted or if the connector is
mounted to a panel having a thickness less than 3.17 millimeters
[.125 inch], slide the spacer over the threads (if using Kit 201540–[ ],
a spacer is not required).
2. If the connector is not panel–mounted or if the connector is
mounted to a panel having a thickness less than 3.17 millimeters
[.125 inch], slide the spacer over the threads (if using Kit 201540–[ ],
a spacer is not required).
3. Thread the lock washer and hex nut onto the threads.
Tighten the hex nut.
3. Thread the lock washer and hex nut onto the threads.
Tighten the hex nut.
4. REVISION SUMMARY
4. REVISION SUMMARY
Revisions to this instruction sheet include:
S Updated document to corporate requirements
S Removed obsolete part numbers
S Added tool to Section 2
Revisions to this instruction sheet include:
S Updated document to corporate requirements
S Removed obsolete part numbers
S Added tool to Section 2
Lock
Washer
Hex
Nut
Lock
Washer
Spacer
Hex
Nut
Spacer
Note: Composite Illustration
Note: Composite Illustration
Guide
Socket
Guide
Socket
Guide
Pin
Guide
Pin
Connector
Connector
Lock
Washer
Lock
Washer
Hex
Nut
Hex
Nut
Connector
Connector
Guide
Pin
Hex
Nut
2 of 2
Lock
Washer
Guide
Pin
Hex
Nut
Figure 2
Tyco Electronics Corporation
Rev A
2 of 2
Lock
Washer
Figure 2
Tyco Electronics Corporation
Rev A
Download