[
TENBY WHITE
]
Products and systems
A famous name with a
fresh new look
The Tenby name has always been synonymous with quality, and by harnessing
the international design and development resources of Legrand, the range has
evolved to meet the style requirements of today’s end users and the
installation needs of today’s professionals.
Switching
Power
VDI and control
Standard engraving
A selection of standard engravings
are available. See p. 106.
The installer’s choice
With its trademark looks, the Tenby range of wiring
accessories has always been a firm favourite in the UK.
Wide rocker
The latest incarnation of the range has clean, simple
lines with rockers that are now larger and slightly
contoured for a more tactile feel.
MORE THAN JUST A PRETTY FACE
Clear Cat. No.
identification
Generous wiring space
100
Captive backed-off
terminal screws
Optional screw caps
Clearly visible
moulded markings
Robust white
thermoset front plate
The Tenby Clipper range of large
rocker switches represents an ideal
solution to Part M’s ease of
operation requirements.
101
Tenby ®
white
7360 11
7360 22
7360 05
7360 32
7360 62
7361 04
Front plates : white thermoset
Terminal screws captive and backed off ready for cabling
Supplied with faceplate screw caps
Surface mounting boxes (see p. 112)
Pack
Cat. Nos.
Single pole plate switches
10 AX - 250 V
±
Pack
Cat. Nos.
Rotary dimming and push on/off
For use with 230 V AC
Not suitable for fluorescent load
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
Flush mounting back box : min. 16 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7360 11
7360 12
7360 13
1 gang – 1 way
1 gang – 2 way
1 gang – intermediate
7360 22
2 gang – 2 way
Dimmers for use with tungsten filament lamps and
good quality GU10 halogen lamps
1
10
7360 32
7360 05
3 gang – 2 way
7360 42
4 gang – 2 way
5
7360 62
6 gang – 2 way
1 gang – 2 way 50 Hz
60 W- 400 W push on/off rotary
Dimmers for use with tungsten filament lamps,
GU10 halogen lamps and low voltage systems
using appropriate transformer
Nominal plate dimensions : 86 x 146 mm
5
1
7360 03
1 gang – 2 way 50 Hz
40 W- 250 W push on/off rotary
1
7360 04
2 gang – 2 way 50 Hz
40 W- 250 W push on/off rotary
Dimmer units - 230 V
Conform to BS EN 60669-2-1 : 2000 and
BS EN 55015
Conforms to BS EN 60669-1 : 2000
Rotary dimming and push on/off
For use with 230 V AC - 50-60 Hz
Not suitable for fluorescent load
Flush mounting back box : min. 25 mm deep
Flush mounting back box : min. 16 mm deep
Nominal plate dimensions : 86 x 86 mm
7360 14
± - electronic
Single pole push switch
10 A - 250 V
±
5
±
Conform to BS EN 60669-2-1 : 2000 and
BS EN 55015
Conform to BS EN 60669-1 : 2000
10
10
10
Dimmer units - 230 V
Dimmers for use with tungsten filament lamps, good
quality wire-wound transformers and compatible
electronic transformers for low voltage loads(1)
1 gang – 2 way push switch
Nominal plate dimensions : 86 x 86 mm
1
7361 03
1 gang – 2 way 50 Hz
40 W- 400 W push on/off rotary
1
7361 04
2 gang – 2 way 50 Hz
40 W- 400 W push on/off rotary
Nominal plate dimensions : 86 x 146 mm
(1) Can be used in conjunction with compatible electronic transformers
for low voltage loads. It will be necessary to test that the dimmer
mechanism is compatible with the electronic transformer identified
for installation
102
Tenby ®
white (continued)
7360 15
7361 81
7360 18
7360 28
7361 91
7361 82
7360 17
7360 54
Front plates : white thermoset
Terminal screws captive and backed off ready for cabling
Supplied with faceplate screw caps
Surface mounting boxes (p. 112)
Pack
Cat. Nos.
Isolator switch 10 A - 250 V
3 pole
±
Pack
Cat. Nos.
With integrated padlockable safety block
in OFF position
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
7360 15
±
Conform to BS 1363 - Part 2 : 1995
Conventional earth pin release shutter
Single earth terminal
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
Conforms to BS EN 60669-2-4
10
Single pole socket outlets 13 A - 250 V
10
7360 18
1 gang – switched
10
7360 19
1 gang – switched
with red power indicator
3 pole isolator switch
731009.eps
Double pole socket outlets 13 A - 250 V
±
Nominal plate dimensions : 86 x 146 mm
Conform to BS 1363 - Part 2 : 1995
Patented 3 pin safety shutter mechanism
2 earth terminals
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7361 81
1 gang – switched
10
7361 91
1 gang – switched
with red power indicator
5
7360 28
2 gang – switched
5
7360 29
2 gang – switched
with red power indicator
Unswitched socket outlets 13 A - 250 V
Nominal plate dimensions : 86 x 146 mm
5
7361 82
2 gang – switched
5
7361 92
2 gang – switched
with red power indicator
±
Conform to BS 1363 - Part 2 : 1995
Patented 3 pin safety shutter mechanism
2 earth terminals
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 1 gang - 86 x 86 mm
2 gang - 86 x 146 mm
10
7360 17
5
7360 27
1 gang – unswitched
2 gang – unswitched
Socket outlets 15 A - 250 V
±
Conform to BS 546 : 1950
Patented 3 pin safety shutter mechanism
Flush mounting back box : min. 35 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7360 54
1 gang – unswitched
10
7360 55
1 gang – switched
103
Tenby ®
white (continued)
7360 51
7360 41
7360 39
7360 48
7360 49
7360 47
7360 30
Front plates : white thermoset
Terminal screws captive and backed off ready for cabling
Supplied with faceplate screw caps
Surface mounting boxes (p. 112)
Pack
Cat. Nos.
Socket outlets 5 A - 250 V
±
Pack
Cat. Nos.
±
(1)
Conform to BS 546 : 1950
Conform to BS EN 60669-1 : 2000
Patented 3 pin safety shutter mechanism
2 earth terminals
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
Use cord outlet accessory box Cat. No. 7300 53 for
flush to wall external cord connection, (see p. 42)
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7360 51
1 gang – unswitched
10
7360 48
10
7360 52
1 gang – switched
10
7360 46
10
7360 49
10
7360 47
10
7360 45
Shaver socket
Conforms to BS EN 61558-2-5 : 1998
IP 24
For use with European, British, American and
Australian 2 pin plugs
Screwless live and neutral terminals
Double wound isolating transformer
Automatic self-resetting overload feature
Plug insertion operates microswitch which energises
transformer
Flush mounting back box : min. 47 mm deep
Nominal plate dimensions : 146 x 86 mm
1
Double pole switches 20 A - 250 V
7360 41
120V
230V
WATERR
HEATE
20 A DP with bottom cord outlet
marked “WATER HEATER”
20 A DP with bottom cord outlet
+ red power indicator
WATERR
HEATE
SINK
OFF
H
ON BAT
20 A DP with bottom cord outlet
marked “WATER HEATER”
+ red power indicator
20 A DP sink/bath dual switch
+ red power indicator
Cable outlet 20 A - 250 V
±
Conforms to BS 5733 : 1995
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
Supply : 230 V - 50/60 Hz
Output : 230/120 V - 20 VA max.
10
Fused connection units 13 A - 250 V
20 A DP with bottom cord outlet
7360 30
20 A – with terminal block and outlet gland
±
(1)
Conform to BS 1363 - Part 4 : 1995
Fused 13 A (fuse supplied)
Fuse drawer retained by quarter turn catch, drawer
padlockable in open position for safety
Use cord outlet accessory box Cat. No. 7300 53 for
flush to wall external cord connection, (see p. 42)
Flush mounting back box : min. 25 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7360 38
Switched, DP with bottom cord outlet
10
7360 39
Switched, DP with bottom cord outlet
+ red power indicator
10
7360 37
Unswitched with bottom cord outlet
Engraving available
see p. 106
(1) Range of engraving available on most products, see table on p. 106
104
(1) Range of engraving available on most products, see table on p. 106
Tenby ®
white (continued)
7360 77
7360 66
7360 71
7360 53
7360 75
7360 00
7360 96
Front plates : white thermoset
Terminal screws captive and backed off ready for cabling
Supplied with faceplate screw caps
Surface mounting boxes (p. 112)
Pack
Cat. Nos.
Double pole switches 45 A - 250 V
±
Conform to BS EN 60669-1 : 2000
Flush mounting back box : min. 48 mm deep
Nominal plate dimensions : 146 x 86 mm
5
5
7360 76
Pack
Cat. Nos.
TV, radio and satellite sockets
Flush mounting back box : min. 35 mm deep
Nominal plate dimensions : 86 x 86 mm
10
7360 71
Screened TV – single, male
Non-isolated
1
7360 70
Screened satellite – single, ‘F’ type
10
7360 72
45 A DP
7360 77
45 A DP + red power indicator
TV
10
7360 53
Nominal plate dimensions : 86 x 86 mm
10
7360 66
FM
SAT
TV
Screened TV + FM
Isolated
Screened TV + ‘F’ type satellite
Non-isolated
45 A DP
Telephone sockets
10
7360 67
Shuttered
Flush mounting back box : min. 35 mm deep
Nominal plate dimensions : 86 x 86 mm
45 A DP + red power indicator
10
7360 00
Single master
10
7360 01
Single secondary
Cooker control units
Conform to BS 4177 : 1992
45 A - 250 V double pole switch with
13 A - 250 V double pole switched socket outlet
Flush mounting back box : min. 48 mm deep
Nominal plate dimensions : 86 x 146 mm
±
±
Data sockets
5
DP with DP switched socket
7360 74
COOK
5
CAT 6 compliant
UTP
Rapid cable connection
Flush mounting back box : min. 35 mm deep
Nominal plate dimensions : 86 x 86 mm
ER
7360 75
DP with DP switched socket +
red power indicator
COOK
ER
Cable outlet 45 A - 250 V
±
Conforms to BS 5733 : 1995
2 piece design for safety
Flush mounting back box : min. 48 mm deep
Nominal plate dimensions : 86 x 86 mm
1
7360 95
RJ45 – single
1
7360 96
RJ45 – double
Blanking plates
5
7360 80
45 A – with terminal block
10
7360 07
10
7360 08
1 gang - 86 x 86 mm
2 gang - 86 x 146 mm
105
Tenby ®
other accessories
white (continued)
■ Tenby white standard engraving
20 A DP SWITCHES
Engraving
AIR CONDITIONER
APPLIANCE
BELL
Bell symbol
CENTRAL HEATING
COOKER HOOD
DISHWASHER
EXTRACTOR
EXTRACTOR HOOD
FAN
Fan symbol
FREEZER
FRIDGE
FRIDGE FREEZER
HEATER
HOB
MICROWAVE
ON / OFF
OVEN
TOWEL RAIL
TUMBLE DRYER
WASHER DRYER
WASHING MACHINE
WATER HEATER
Without neon
With neon
7360 48AC
7360 48AP
7360 48BL
7360 48BY
7360 48CG
7360 48CH
7360 48DW
7360 48EX
7360 48EH
7360 48FN
7360 48FY
7360 48FZ
7360 48FR
7360 48FF
7360 48HR
7360 48HB
7360 48MW
7360 48OO
7360 48OV
7360 48TR
7360 48TD
7360 48WD
7360 48WM
7360 48WH
7360 49AC
7360 49AP
7360 49BL
7360 49BY
7360 49CG
7360 49CH
7360 49DW
7360 49EX
7360 49EH
7360 49FN
7360 49FY
7360 49FZ
7360 49FR
7360 49FF
7360 49HR
7360 49HB
7360 49MW
7360 49OO
7360 49OV
7360 49TR
7360 49TD
7360 49WD
7360 49WM
7360 49WH
7811
7815
7832
7822
1200
Pack
Cat. Nos.
White
0816 59
Tenby clipper switches 10 AX
Conform to BS 3676 : Part 1
Concealed fixing screws
For flush mounting, see boxes p. 113
For surface mounting, see boxes p. 112
Dimensions : 86 x 86 mm
Fixing centres : 60·3 mm
10
10
10
7811
7812
7813
1 gang – 1 way SP
1 gang – 2 way SP
1 gang – intermediate SP (6 AX only)
10
7814
1 gang – push switch SP (6 AX only)
10
7815
1 gang – TP switch marked ‘ON-OFF’ and
fan symbol
OFF
ON
13 A FUSED CONNECTION UNITS
Engraving
AIR CONDITIONER
APPLIANCE
BELL
Bell symbol
CENTRAL HEATING
COOKER HOOD
DISHWASHER
EXTRACTOR
EXTRACTOR HOOD
FAN
Fan symbol
FREEZER
FRIDGE
FRIDGE FREEZER
HEATER
HOB
MICROWAVE
ON / OFF
OVEN
TOWEL RAIL
TUMBLE DRYER
WASHER DRYER
WASHING MACHINE
WATER HEATER
Switched
Switched
with neon
Unswitched
7360 38AC
7360 38AP
7360 38BL
7360 38BY
7360 38CG
7360 38CH
7360 38DW
7360 38EX
7360 38EH
7360 38FN
7360 38FY
7360 38FZ
7360 38FR
7360 38FF
7360 38HR
7360 38HB
7360 38MW
7360 38OO
7360 38OV
7360 38TR
7360 38TD
7360 38WD
7360 38WM
7360 38WH
7360 39AC
7360 39AP
7360 39BL
7360 39BY
7360 39CG
7360 39CH
7360 39DW
7360 39EX
7360 39EH
7360 39FN
7360 39FY
7360 39FZ
7360 39FR
7360 39FF
7360 39HR
7360 39HB
7360 39MW
7360 39OO
7360 39OV
7360 39TR
7360 39TD
7360 39WD
7360 39WM
7360 39WH
7360 37AC
7360 37AP
7360 37BL
7360 37BY
7360 37CG
7360 37CH
7360 37DW
7360 37EX
7360 37EH
7360 37FN
7360 37FY
7360 37FZ
7360 37FR
7360 37FF
7360 37HR
7360 37HB
7360 37MW
7360 37OO
7360 37OV
7360 37TR
7360 37TD
7360 37WD
7360 37WM
7360 37WH
Full box quantities only - Pack quantity 10
Engraved markings differ slightly from pad printed markings appearing
elsewhere in the catalogue. For lead times of above engravings,
please contact us on 0845 605 4333
106
10
7822
2 gang – 2 way SP
10
7832
3 gang – 2 way SP
Neon plate switch locator
Clear plastic moulding plus 2 neon lamps
Emits a soft green glow which assists the location of
switch in the dark
Not suitable for use with fluorescent or energy
saving lamps
Dimensions : 98 x 98 mm
1
For use with 1, 2 and 3 gang plate switches
1200
Saxonguard RCD spur unit
Conforms to BS 7288 and BS 1363 : Part 4
Passive : mechanical latching - does NOT trip on
power failure
Flush mounting in box Cat. No. 0891 10
Dimensions : 86 x 86 mm
1
0816 59
1 gang spur unit 30 mA
F
U
S
E