The FLEXUS series is suitable for
protecting information and
telecommunications systems, information
networks and critical systems in general,
where the risks connected with a power
supply of poor quality energy could put
the continuity of activities and services at
risk, entailing high costs.
The FLEXUS series is available in 10-1215-20 kVA three-phase input and output
models, with double conversion on-line
technology according to the VFI-SS-111
classification, as defined by the IEC EN
62040-3 standard. Flexus has been
designed and produced with state-ofthe-art technologies and components, in
order to guarantee maximum protection
for the users powered, no impact on the
supply mains and energy saving.
Flexus
impact on the power supply source, be it
the mains or a generator set:
• low distortion of input current – less
than 3%
• input power factor 0.99
• power walk-in function that guarantees
progressive start-up of the rectifier
• delayed switching-on function, to
restart the rectifier igniters when the
mains returns, in case of systems with
various UPS
The Flexus also acts a filter and phaseshift mechanism in respect of the supply
mains ahead of the UPS, since it
removes the harmonic components and
the reactive power generated by the
users powered.
• Charge block system to reduce
consumption of the electrolyte and
further extend the life of VRLA
batteries.
Compensation of the recharge voltage
according to temperature in order to
avoid excessive charges and battery
overheating.
Battery Test in order to detect any falloff in performance or failure of the
batteries in good time.
Protection against deep discharges: in
case of long low load discharges, the
end-of-discharge voltage tension will be
BATTERY CARE SYSTEM
ZERO IMPACT SOURCE
Thanks to the technology used, Flexus
can solve any problem of connection in
installations where the supply mains has
a limited installed power, where the UPS
is also powered by a generator set or
where there are problems of compatibility
with loads that generate current
harmonics; Flexus has indeed zero
Management of the batteries is
fundamental to guaranteeing operation of
the power supply unit under emergency
conditions. The Battery Care System
consists of a series of functions and
performances that permit management
of the storage batteries in such a way as
to obtain the best performance and to
extend battery life.
increased, as prescribed by the battery
manufacturers, in order to avoid damage
to or a drop in performance of the
storage batteries.
Ripple Current: the recharge ripple
current (residual AC component) is one
of the most important causes that reduce
battery reliability and life. Flexus, thanks to
the high-frequency battery charger,
reduces this value to negligible levels,
extending battery life and maintaining
high performance for a long time.
Wide voltage range: the rectifier is
made to be operated with a wide range
of values of the input voltage (up to 40% with half load), reducing the need
to discharge the batteries and, as a
result, extending battery life.
LOW MANAGEMENT COST
The technology used and the choice of
high performance components mean
that Flexus can obtain exceptional
performance and efficiency levels, from a
very low footprint and dimensions:
• the lowest footprint in this category,
only 0.26 sq. m. for 20kVA Flexus,
batteries included
• high performance up to 94% that
permits 35% of the energy dissipated
in one year to be saved, compared to
similar products present on the market
(with average performance 91%). This
exceptional performance value makes
it possible to recover the initial
investment in less than 4 years in
operation.
• output power with power factor 0.9
that provides up to 15% more active
power compared to a normal UPS in
commerce, guaranteeing the greatest
margin in sizing of the UPS for further
load increases
FLEXIBILITY
Flexus can be used for a wide range of
applications, thanks to its characteristics
of configuration flexibility, accessories
and options available and performance
levels:
• suitable for powering capacitive loads
such as blade servers, without any
reduction of the active power, from 0.9
leading to 0.9 lagging
• modes of operation: On Line, Eco,
Smart Active and Stand By Off
Battery recharge: Flexus is suitable for
working with hermetically sealed (VRLA),
AGM and GEL lead batteries, and openvase and Nickel-Cadmium batteries.
According to the type of battery, various
recharge methods are available.
• One-level recharge, typical for the
most commonly used VRLA AGM
batteries
• Two voltage levels recharge according
the IU characteristic
Leading Cosϕ (capacitive loads)
cosϕ 0,9
Flexus Output Power
cosϕ 1
100% kW
Lagging Cosϕ (inductive loads)
cosϕ 0,9
1,00
0,75
Active Power
0,50
100% kVA
UPS @ Cosϕ 0,9
Es. 20kVA - 18kW !!!
0,25
-1
-0,8
-0,6
-0,4
-0,2
0
0,2
0,4
0,6
0,8
1
Reactive Power
• 3 slots for the installation of optional
communication accessories such as
network adapters, zero-potential
contacts, etc.
• REPO (Remote Emergency Power Off)
with which to power down the UPS
through a remote emergency
pushbutton
• Input for connection of the auxiliary
contact of an external manual bypass
• Input for synchronization from an
external source
• Graphic mimic panel display for remote
connection
• frequency converter mode
• Power Share sockets that can be
configured in order to maintain the
back-up time for the most critical loads
or to be activated only when the mains
goes down
• Cold Start to switch on the UPS
including when the supply mains is off
• battery cabinets of various dimensions
and capacity, for longer back-up times
• option to connect a temperature
sensor for external battery cabinets, for
recharge voltage compensation
• additional battery chargers to optimize
recharge times
• optional double input of the supply
mains
• isolation transformers to modify the
neutral arrangements, in case of
separate sources or for galvanic
isolation between input and output
ADVANCED COMMUNICATION
Flexus is equipped with a graphic display
that provides information, measures,
states and alarms regarding the UPS in
5 different languages.
• Advanced multiplatform
communication, for all operating
systems and network environments:
Watch&Save 3000 monitoring and
shutdown software included with
SNMP agent
• Compatible with PowerNetGuard for
the remote assistance service
RS232 or USB serial port
LE FOR
SUITABY LIGHTING
NC
EMERGEPLICATIONS
AP
50
51
Three-phase input
Three-phase output
Three-phase input
Three-phase output
Flexus
Flexus
Models
Power (kVA)
Technical data
FT 10
10
FT 12
12
FT 15
15
FT 20
20
System
Weight with internal batteries (kg)
FT 10
180
FT 12
182
Dimensions (hwd) (mm)
Input
FT 10
Rated voltage
FT 12
FT 15
FT 20
FT 15
FT 20
Compliance
380-400-415 Vac three-phase +N
FT 20
195
90% non condensing
Colour
Dark grey (RAL 7024)
< 56 dBA at 1 m
Protection rating
IP20
Efficiency
FT 12
3+N
Number of phases
190
3 communication interface slots/RS232/USB
O°C - 40°C
Relative humidity
50/60 Hz
40 ÷ 72 Hz
Noise
0.99 Pf
THDI ≤ 3%
FT 10
180 ± 264V (selectable)
Voltage tolerance
FT 15
930 x 320 x 840
Communication
Operating temperature
380- 400-415 Vac three-phase +N
Rated frequency
Frequency tolerance
Power factor at full load
Current distortion
By pass
Rated voltage
50 or 60 Hz (selectable)
Rated frequency
Frequency tolerance
Output
≥ 94% in On-line mode, ≥ 98% in Economy mode
European Directives: L V 73/23/EC and 93/68/EC Low voltage directive
EMC 2004/108/EC and 89/336/EC Electromagnetic compatibility directive
Standards: Safety IEC EN 62040-1; EMC IEC EN 62040-2 C2
Classification according to IEC 62040-3 (Voltage Frequency Independent) VFI - SS - 111
Details
±5 (selectable)
FT 10
9
Active power with load PF from 0,9 cap. to 0,9 ind.
10
Rated power (kVA)
FT 12
FT 15
12
15
10.8
13.5
3+N
Number of phases
0.9
Output power factor
3:1
Crest factor (Ipeak/Irms)
± 3%
Dynamic variation
± 1%
Static variation
380-400-415 Vac (selectable)
Rated voltage
Voltage distortion
FT 20
Communication
interface slot
Powershare
sockets
20
18
Remote
contacts
connectors
Parallel board
Serial
interface port
USB port
≤ 1% with linear load / ≤ 3% with non-linear load
Frequency
50/60 Hz
Frequency stability on battery mode
0.01%
Overload at Pf 0.8
Batteries
115% infinite, 125% for 10 minutes, 150% for 1 minute, 168% for 5 seconds
FT 10
FT 12
Type
FT 15
FT 20
VRLA AGM/GEL
Recharge time
6h
52
53
Personal
computerS
iPlug
600-800 VA
single-phase
ECO LINE
The iPlug series is the ideal solution for household, and small home
office systems. Its compact size and versatility - push-button operation,
LED status panel and user-replaceable batteries - make iPlug easy to
install within a domestic environment to protect systems from surges
and blackouts. When mains power fails the load is powered by the
inverter and built-in battery. PowerShield3 UPS monitoring and control
software (available for download from www.riello-ups.com) can be used
for an orderly unattended shutdown of IT systems.
LOAD CONFIGURATOR
Load type
Power (VA)*
Personal computer
250
LCD Monitor
70
15” Monitor
150
Scanner, printer
200
Modem, TV, DVD reader, PlayStation, Hi-Fi, Phone, Fax
50
Laser printer**
200
*Average estimated value. **Use the iPLUG filtered power output.
FEATURES
• ECO LINE energy efficient product
• Compact, ergonomic design
• 5 sockets with battery backup
•3 sockets with surge protection only
• Cold start capability to power up the UPS without mains power
• User replaceable batteries
• USB interface for remote monitoring
• Power cable included
• Protection from short-circuits
• Auto restart - when the mains returns after battery exhaustion
• GS/Nemko safety marking
• Available with French (2P+E), English, Schuko and Italian outlets.
ADVANCED COMMUNICATION
•PowerShield3 supervision and shut-down software for Windows 7,
2008, Vista, 2003, XP, Linux, Mac OS X and Sun Solaris operating
systems
• Plug and Play function.
2 YEAR WARRANTY
MODELS
POWER
iPlug 600
iPlug 800
600VA/360W
800VA/480W
INPUT
Rated voltage
220-240 Vac
Voltage range
230 Vac (+20/-25%)
Frequency
50/60 Hz with auto sensing
OUTPUT
Voltage on mains operation
230 Vac (+20/-25%)
Voltage on battery operation
230 Vac (+/- 10%)
Frequency on battery operation
50 or 60 Hz (+/- 1%)
BATTERIES
VRLA AGM Maintenance-free lead-acid
Type
Recharge time
6-8 h
ENVIRONMENTAL
Net weight (kg)
Gross weight (kg)
3.7
4.1
4
4.4
Dimensions (hwd) (mm)
99 x 175 x 313
Packaging dimensions (hwd) (mm)
260 x 380 x 140
Communication
Compliance
USB
EN 62040-1-1 and Directive 2006/95/EC; EN 62040-3
EN 62040-2 and Directive 2004/108 EC
CE; GS/NEMKO on Schuko version
Marks
Operating temperature
0°C / +40°C
Colour
Altitude and relative humidity
Black
6000 meters max. elevation, <95% non condensing
Accessories provided
1 input supply cable, user guide
iPlug 600 - iPlug 800
Rear detail
Sockets with UPS protection
(no break in power if mains fails)
IEC OUTLETS WITH UPS PROTECTION
SAFETY FUSE
USB communication port
Filtered socketS: overvoltage protection only
TECHNICAL DETAILS
LED detail
AVAILABLE SOCKETS
schuko
socket
French
socket
ITALIAN
socket
British
socket
CEE 7/7P
CEE 7/5
CEI 23/16
BS1363A
QUALITY POWER SUPPLY
SENTRY MPS is an on-line double
conversion UPS (VFI SS 111 in
accordance with IEC EN 62040-3) with
a transformer isolated inverter. With a
compact footprint and high power quality
output, SENTRY MPS is designed to
protect “mission critical” applications
including data processing,
telecommunications, industrial
processes, security and electro-medical
systems.
SENTRY MPS is available from 100 to
800kVA in two or four versions each with
different harmonic distortion and power
factor for better matching the market
requirements:
•
•
•
•
MPS (100 to 200kVA only),
MPS LH (100 to 200kVA only),
MPS Plus,
MPS Sinus.
Sentry MPS
Three-phase output
FLEXIBILITY
SENTRY MPS technology removes the
problems of over sizing downstream
power sources, whilst improving load
power factors and current harmonics.
The UPS features the latest input current
absorption techniques including
progressive rectifier start-up and the
option to reduce battery charging
currents. These features make SENTRY
MPS one of the most generator
compatible and environmentally friendly
UPS available.
Traditionally, when a mains supply is
present the UPS charges its batteries.
Battery power is used for the inverter
should the input supply fail. Efficient
battery management and care is
therefore essential to the overall
performance of the UPS in an
emergency. The SENTRY MPS Battery
Care System consists of a range
of features designed to provide
optimum performance and enhanced
operating life:
• Dual level charging regime to
optimise recharge currents and lower
recharge times;
• Temperature compensation and deep
discharge protection to reduce overall
battery aging;
• Charge blocking system to reduce
electrolyte consumption and lengthen
the life of VRLA batteries;
• Predictive battery testing to spot
potential battery deterioration and
failure.
SENTRY MPS is also compatible with
different battery technologies: openvase lead acid and AGM and Gel
VRLA, NiCd.
MINIMUM INPACT ON SUPPLIES EASY SOURCE
BATTERY CARE SYSTEM: MAXIMUM
LIFETIME POTENTIAL
SENTRY MPS is suitable for a wide
range of applications including IT and the
most demanding industrial environments
suitable for power capacitive loads such
as blade servers, without any reduction
of the active power, from 0,8 lagging to
0,9 leading. With a broad of accessories
and options, complex configurations and
system architectures can be achieved to
guarantee maximum power availability
and the option to add new UPS without
interruption to existing users. Using the
AROS UPS Group Synchroniser (USG)
and Parallel Systems Joiner (PSJ)
sophisticated inter group parallel and
redundant systems can be achieved to
provide the highest possible levels of
resilience and availability.
EASY INSTALLATION
SENTRY MPS has a small footprint
(only 0,64 sqm for 200kVA and 1,63
sqm for 400kVA). Front access to
internal assemblies and top panel
ventilation make space allocation within
confined data processing or plant
rooms easy. SENTRY MPS can be
placed against a wall as there is no
requirement for rear or side panel
access for maintenance or ventilation.
Leading Cosϕ (capacitive loads)
cosϕ 0,9
cosϕ 0,8
MPS Output Power
100% kW
cosϕ 1
cosϕ 0,9
Lagging Cosϕ (inductive loads)
cosϕ 0,8
cosϕ 0,7
1,00
0,75
cosϕ 0,6
Active Power
100% kVA
0,50
0,25
-1
-0,8
-0,6
-0,4
-0,2
0
0,2
0,4
0,6
0,8
1
1,2
Reactive Power
APPLICATIONS
ADVANCED COMMUNICATION
• Servers
• Local Area Network (LAN)
• Data centers
• Telecommunications
• Industrial equipment
• Electro-medical equipment
• Compatible with PowerNetGuard for
remote maintenance
• Advanced, multi-platform
communication, for all operating
systems and network environments:
Watch&Save 3000 supervision and
shut-down software included, with
SNMP agent, for Windows 95, 98, NT
4.0, Me, 2000, 2003, XP, Mac OS 9.x,
X, Linux, Novell operating systems. The
UPS is supplied with a cable for direct
connection to the PC (Plug and Play)
• RS232 double serial port
• Slot for installation of the mains
adapter; EPO contact (Emergency
Switching Device) for switching off the
UPS with a remote emergency switch
• Remote mimic panel (LED or LCD)
• Graphic Remote Panel
OPTIONS
Input Isolation transformer
UPS Group Syncroniser (UGS)
Parallel System Joiner (PSJ)
Interface for generator
LED remote status panel
LCD based remote control panel
Graphic Display Remote panel
Empty battery cabinets
for prolonged runtime
66
67
DUAL BUS SYSTEM
The Dual Bus System powers the
priority loads from two independent
sources.
This configuration increases the
redundancy and availability level of a
multi-module configuration. Each bus
may consist of a single module or up to
8 modules in parallel, kept in synchro
by the UGS (UPS Group Synchroniser).
Fig 1- Bock diagram UPS in parallel up to 8 units
Fig. 2 - Dual bus System
EXPANDABILITY
The units can be connected in parallel
up to 8 units to increase power
availability or redundancy.
The single module or the system can
be expanded any time to suit power
requirements without influencing the
initial investment.
Thanks to the peculiarity of the “Hot
System Expansion” feature, the
additional unit can be connected in
parallel while the other units are on-line
and supplying regular power to the
load. The new UPS is on-line and will
be set up automatically.
200kVA
DYNAMIC DUAL BUS SYSTEM
Two independent systems set in Dual
Bus Configuration can be merged
together at any time for system
expansion or maintenance thanks to
the PSJ (Parallel System Joiner) option.
This provides a lot of flexibility in your
installation in case of maintenance or
when it is necessary to change the
redundancy level of both systems.
Fig. 3 - Dynamic Dual Bus System
68
69
Three-phase input
Three-phase output
Three-phase input
Three-phase output
Sentry MPS
Sentry MPS
Models
Power (kVA)
Input
Technical data
MPS 100
100
MPS 100
MPS 120
120
MPS 120
MPS 160
160
MPS 160
400 V ± 20%
Voltage tolerance
380 - 400 - 415 Vac three-phase
Nominal voltage
Frequency
MPS 200
200
MPS 200
MPS 120
MPS 160
MPS 120
Models
Power (kVA)
Technical data
MPS 250
250
MPS 250
160
MPS 200
200
160
Output
Rated power (kVA)
Active power with load PF from 0,9 cap. to 0,8 ind. (kW)
MPS 160
810
System
Weight (kg)
MPS 300
300
MPS 300
MPS 400
400
MPS 400
Lead, open vase acid and VRLA, AGM / GEL; NiCd
250
MPS 300
MPS 400
300
400
240
320
3+N
≤1%
50 or 60 Hz configurable
3:1
Overload
MPS 200
110% for 60’; 125% for 10’; 150% for 1’
MPS 250
MPS 300
MPS 400
Voltage-free contacts (configurable)
EPO and bypass
Double RS232 + remote contacts + 2 communication interface slots
Up to 94%
Dimensions (wdh) (mm)
770
63 ÷ 68 dBA a 1 m
850x1630x1900
2200
1000x1630x1900
2200
Noise level
2600
70 dBA a 1 m
Operating temperature
0 °C / +40 °C
Relative humidity
<95% non condensing
IP20
Colour
Compliance
MPS 400
>0.95 in the Sinus version
0 ÷ 100% in 30’’ configurable
± 2% (selectable from ± 1% to ± 5% from the front panel)
Back Feed protection; separable bypass line
MPS 250
Zero
-0,5 Vx °C
MPS 250
200
Number of phases
380 - 400 - 415 Vac three-phase + N
± 1%
± 5% in 10 msec.
≤3%
Frequency
Sinusoidal
Crest factor (Ipeak/Ipms)
MPS 120
System
Remote signalling
Communication
Efficiency
650
0 °C / +40 °C
<95% non condensing
Relative humidity
Protection degree
Light grey (RAL 7035)
Directives EEC 73/23 - 93/68 - 89/336
Safety IEC EN 62040-1; EMC IEC EN 62040-2; Performance IEC EN 62040-3
(Voltage Frequency Independent) VFI - SS - 111
MPS 300
400 V ± 20%
45 ÷ 65 Hz
Power factor
Battery
Type
AC ripple current
Temperature compensation
MPS 160
120
128
3+N
Nominal voltage
Static stability
Dynamic stability
Voltage distortion with linear load
≤1%
MPS 100
<3% in the Sinus version
Soft start
Permitted frequency tolerance
Standard features
MPS 200
Lead, open vase acid and VRLA, AGM / GEL; NiCd
100
96
380 - 400 - 415Vac three-phase + N
± 1%
± 5% in 10 msec.
Voltage distortion with linear load
50 or 60 Hz configurable
Frequency
Waveform
3:1
110% for 60’; 125% for 10’; 150% for 1’
Voltage-free contacts (configurable)
Remote signalling
Remote commands
Double RS232 + remote contacts + 2 communication interface slots
Up to 94%
800x800x1900 (base version)
640
380 - 400 - 415 Vac three-phase
Frequency
>0.95 in the Sinus version
Power factor
Current harmonic distortion
0 ÷ 100% in 30’’ configurable
± 2% (selectable from ± 1% to ± 5% from the front panel)
Back Feed protection; separable bypass line
MPS 100
Zero
-0,5 Vx °C
MPS 100
Rated power (kVA)
Input
Nominal voltage
Voltage tolerance
45 ÷ 65 Hz
<3% in the Sinus version
Current harmonic distortion
Soft start
Permitted frequency tolerance
Standard features
Battery
Type
AC ripple current
Temperature compensation
Output
80
Active power with load PF from 0,9 cap. to 0,8 ind. (kW)
Number of phases
Nominal voltage
Static stability
Dynamic stability
Voltage distortion with non linear load
≤3%
Voltage distortion with non linear load
Sinusoidal
Waveform
Crest factor (Ipeak/Ipms)
Overload
EPO and bypass
Remote commands
Communication
Efficiency
Dimensions (wdh) (mm)
Weight (kg)
Noise level
Operating temperature
IP20
Protection degree
Colour
Compliance
Classification as per IEC 62040-3
Light grey (RAL 7035)
Directives EEC 73/23 - 93/68 - 89/336
Safety IEC EN 62040-1; EMC IEC EN 62040-2; Performance IEC EN 62040-3
Classification as per IEC 62040-3
(Voltage Frequency Independent) VFI - SS - 111
70
71
Sentry MPS
Technical data
Three-phase input
Three-phase output
Models
Power (kVA)
Input
MPS 500
500
MPS 500
MPS 600
600
MPS 600
400 V ± 20%
Voltage tolerance
380 - 400 - 415 Vac three-phase
Nominal voltage
Frequency
MPS 800
800
MPS 800
45 ÷ 65 Hz
<3% in the Sinus version
Current harmonic distortion
>0.93 in the Sinus version
Power factor
Soft start
0 ± 100% in 30" configurable
Permitted frequency tolerance
± 2% (selectable from ± 1% to ± 5% from the front panel)
Standard features
Battery
Back Feed protection; separable bypass line
MPS 500
Type
MPS 600
MPS 800
Lead, open vase acid and VRLA, AGM / GEL; NiCd
AC ripple current
< 1%
Temperature compensation
Output
-0,5 Vx °C
MPS 500
MPS 600
3+N
Number of phases
480
400
Active power with load PF from 0,9 cap. to 0,8 ind. (kW)
500
Rated power (kVA)
MPS 800
600
Nominal voltage
800
640
380 - 400 - 415 Vac three-phase + N
Static stability
± 1%
Dynamic stability
± 5% in 10 msec.
≤3%
Voltage distortion with non linear load
≤1%
Voltage distortion with linear load
Sinusoidal
Waveform
50 or 60 Hz configurable
Frequency
Crest factor (Ipeak/Ipms)
3:1
Overload
System
110% for 60’; 125% for 10’; 150% for 1’
MPS 500
MPS 600
EPO and bypass
Remote commands
Voltage-free contacts (configurable)
Remote signalling
Communication
MPS 800
Double RS232 + remote contacts + 2 communication interface slots
Efficiency
Up to 94%
Dimensions (wdh) (mm)
3200x980x1900
3600
4400x1000x1900
0 °C / +40 °C
Operating temperature
78 dBA a 1 m
Noise level
4000
Weight (kg)
IP20
Protection degree
<95% non condensing
Relative humidity
Colour
Compliance
5300
Light grey (RAL 7035)
Directives EEC 73/23 - 93/68 - 89/336
Safety IEC EN 62040-1; EMC IEC EN 62040-2; Performance IEC EN 62040-3
Classification as per IEC 62040-3
(Voltage Frequency Independent) VFI - SS - 111
72
Sentry MPS
Single-phase output
Sentry MPS
Technical data
Three-phase input
Single-phase output
Models
Power (kVA)
Input
MPM 30
30
MPM 30
MPM 40
40
MPM 40
MPS 1Ph is an on-line double
conversion UPS (VFI SS 111 in
accordance with IEC EN 62040-3) with
transformers isolated inverter and
rectifier. MPS 1Ph has a compact foot
print and high quality output to provide
the ultimate power protection for
industrial applications:
industrial processes, petrochemical,
power plant, energy etc.
MINIMUM IMPACT ON SUPPLIES EASY SOURCE
PROTECTION FOR INDUSTRIAL
APPLICATION
BATTERY CARE SYSTEM: MAXIMUM
LIFETIME POTENTIAL
Traditionally, when a mains supply is
present the UPS charges its batteries.
Battery power is used for the inverter
should the input supply fail. Efficient
battery management and care is
therefore essential to the overall
performance of the UPS in an
emergency. The MPS 1Ph Battery
Care System consists of a range
of features designed to provide
optimum performance and enhanced
operating life:
• Dual level charging regime to
optimise recharge currents and
lower recharge times
• Temperature compensation and
deep discharge protection to reduce
overall battery aging
• Charge blocking system to reduce
electrolyte consumption and
lengthen the life of VRLA batteries
• Predictive battery testing to spot
potential battery deterioration and
failure
MPS 1Ph is also compatible with
different battery technologies: openvase lead acid and AGM and Gel
VRLA, NiCd.
MPM 60
60
MPM 60
400 V ± 20%
Voltage tolerance
380 - 400 - 415 Vac three-phase
Nominal voltage
Frequency
≥0.93
Power factor
Battery
MPM 80
80
MPM 80
45 ÷ 65 Hz
<5% C
Current harmonic distortion
Soft start
0 ÷ 100% in 120’’ configurable
Permitted frequency tolerance
± 2% (selectable from ± 1% to ± 5% from the front panel)
Standard features
MPS 1Ph technology removes the
problems of over sizing upstream
power sources, whilst improving load
power factors and current harmonics.
The UPS features the latest input
current absorption techniques including
progressive rectifier start-up and the
option to reduce battery charging
currents. These features make MPS
1Ph one of the most generator
compatible and environmentally friendly
UPS available.
INDUSTRIAL ENVIRONMENT
MPS 1Ph is suitable for severe
installation environments such as
petrochemical manufacturing sites,
where the operating conditions (levels of
vibration, mechanical stress, ambient
temperatures and dust ingress) require a
more robust and industrialized UPS
design to those installed within, for
example, data centres.
HIGH Icc
A high short-circuit current (Icc = 3 In)
making the UPS suitable for loads with
high current peaks; during switch-on or
a load step-change.
220V DC VOLTAGE
An input transformer and isolated inverter
to protect the 220Vdc bus bar (from 108
to 114 blocks), the recognised industrial
standard.
REDUNDANT VENTILATION
100% redundant ventilation with 50%
fan loading at nominal load and each
fan monitored for breakdown or failure.
Back Feed protection; separable bypass line
MPM 30
MPM 40
Numeber of cells
MPM 60
MPM 80
108 ÷ 114
Max Vdc
274 V
Temperature compensation
-0,5 Vx °C
FLEXIBILITY
With a broad range of accessories and
options, complex configurations
and system architectures can be
achieved to guarantee maximum power
availability and the option to add new
UPS without interruption to existing
users. Using the Aros UPS Group
Synchroniser (USG) and Parallel
Systems Joiner (PSJ) sophisticated
inter group parallel and redundant
systems can be achieved to provide
the highest possible levels of
resilience and availability.
Output
MPM 30
24
Active power (kW)
30
Rated power (kVA)
MPM 40
MPM 60
40
60
32
Nominal voltage
48
MPM 80
80
64
230Vac single-phase
<1%
Voltage distortion with linear load
± 5%
Dynamic stability
± 1%
Static stability
Voltage distortion with non linear load
<3%
Frequency
50 or 60 Hz configurable
Crest factor (Ipeak/Ipms)
3:1
Overload
110% for 60’; 125% for 10’; 150% for 1’
Short circuit current
3 I nom.
ADVANCED COMMUNICATION
• Compatible with PowerNetGuard for
remote maintenance
• Advanced, multi-platform
communication, for all operating
systems and network environments:
Watch&Save 3000 supervision and
shut-down software included, with
SNMP agent, for Windows 95, 98,
NT 4.0, Me, 2000, 2003, XP, Mac
OS 9.x, X, Linux, Novell operating
systems. The UPS is supplied with a
cable for direct connection to the PC
(Plug and Play)
• RS232 double serial port
• Slot for installation of the mains
adapter; EPO contact (Emergency
Switching Device) for switching off
the UPS with a remote emergency
switch
• Remote mimic panel (LED or LCD)
System
MPM 30
MPM 40
MPM 60
EPO and bypass
Remote commands
Voltage-free contacts
Remote signalling
Communication
MPM 80
Double RS232 + remote contacts + 2 communication interface slots
Efficiency
Up to 94%
Dimensions (wdh) (mm)
Weight (kg)
800x800x1900
850
1600x800x1900
900
1400
0 °C / +40 °C
Operating temperature
Redundant fans
Ventilation
63 ÷ 68 dBA a 1 m
Noise level
IP20
Protection degree
<95% non condensing
Relative humidity
Colour
Compliance
1500
Light grey (RAL 7035)
Directives EC 73/23 - 93/68 - 2004/108
Safety IEC EN 62040-1; EMC IEC EN 62040-2; Performance IEC EN 62040-3
Classification as per IEC 62040-3
(Voltage Frequency Independent) VFI - SS - 111
74
75
LE FOR
SUITABY LIGHTING
NC
EMERGEPLICATIONS
AP
Sentry Multistandard
SENTRY MULTISTANDARD provides
maximum protection for critical data
processing networks and security
applications, thanks to its advanced
design, selectable operating modes and
communications capabilities. Operating
modes include: On-line, Economy,
Smart-Active, Standby/Off and Voltage
Stabilisation. Standard communications
features include a front panel LCD with
128 potential messages, RS232
interfaces, EPO input, communications
interface slot and Watch&Save 3000
management software.
The SENTRY MULTISTANDARD series
includes 10-15-20kVA single/singlephase, three/single-phase and 10-1520-30-40-60-80 kVA three-phase
models, and uses on-line double
conversion technology (VFI). The load is
powered continuously by the inverter with
a filtered, stabilised and regulated
sinewave supply. The input and output
filters considerably increase the immunity
of the load to mains disturbances and
surges, even on bypass.
10/30 kVA
LOW POWER CONSUMPTION
• On-line Mode: up to 92% efficiency
can be achieved due to the use of
IGBT technology, increasing to 98% in
one of the other operating modes
• Economy Mode: uses Line Interactive
(VI) technology to power less critical
loads from the mains supply for certain
periods
• Smart Active: if the mains supply is out
of range, the UPS will power the load
from the inverter as an On-line UPS.
When the mains supply returns to
within range again, the UPS will monitor
this for a certain period before selecting
Line Interactive operation.
Fig. 1 – Block diagram UPS in parallel up to 8 units
10/30 kVA
• Automatic battery test
• Recharge compensated for
temperature
• Automatic or manual rapid charge
(boost) – duration progammable
• Option to connect the UPS to singlephase or three phase mains supplies
(SM series)
• Panel adjustment to offset voltage
drop down long cable runs
HIGH LEVEL BATTERY RELIABILITY
SIMPLE TO INSTALL
For the 40 to 80 kVA models, open the
door and remove the protective panel
(standards requirement) and the power
components - mounted on a sliding tray
- can be pulled out to provide easy
access to all the electrical and electronic
components for maintenance and repair
work. This particular feature means that
the MTTR (Mean Time To Repair) is
much lower than traditional UPS designs
with less easily reached assemblies,
• Connect up to 8 units in parallel for
power capacity or redundancy
MAINTENANCE SIMPLICITY = LOW
MTTR
MAXIMUM RELIABILITY
AND AVAILABILITY
Battery cabinet
which has longer times due to the
compact size of the products and
difficult access to the parts.
A large amount of maintenance
information is available from the front
mimic panel and LCD. In addition
system operating parameters are
software configurable via a local PC to
allow new functions to be added or
adjustments made to operating
specifications.
55
54
SENSITIVE SUPPLY COMPATIBLE
For power supply sources that are
particularly sensitive to harmonics
(generator sets or transformers of low
power with respect to that of the UPS) it
is often a good idea to take action to
limit the harmonics injected back into the
supply by the UPS.
SENTRY MULTISTANDARD series is also
available with built-in active filter using
high frequency Isolated Gate Bipolar
(IGBT) Technology with Digital Signal
Processor (DSP) control. The Active
Filter helps to reduce harmonics
generated by the UPS into the supply
which could disrupt the operation of
downstream generators and
transformers whose rating is closely
matched to that of UPS.
• advanced technology
The active filter reduces harmonic
distortion of the phase and neutral
currents. The Digital Signal Processor
(DSP) and the “current mode” instantly
control and monitor the input current to
maintain a perfect sinewave with less
than 4% harmonic distortion
• maximum efficiency
Thanks to the active filter Sentry
Multistandard systems have low input
distortion even at low loads and their
overall efficiency is not affected by
generator frequency variations or line
impedance
• reduction of neutral current
The active filter reduces the input
neutrals current by up to 3.5 times
their nominal rating to help avoid
oversizing input protections and
conductors
• maximum reliability
Sentry Multistandard systems are
extremely reliable. Overall UPS
performance is unaffected should the
harmonic filter fail
• excellent capabilities
Input distortion: (THDi) less than 4%
Input power factor: >0.99
Efficiency: up to 93%
Leading Cosϕ (capacitive loads)
cosϕ 0,8
Multistandard Output Power
cosϕ 0,9
100% kW
cosϕ 1
cosϕ 0,9
Lagging Cosϕ (inductive loads)
cosϕ 0,8
Operating status, alarms, applied load,
battery charging.
1,00
Sentry Multistandard can also be
supplied without the Active Filter
for installations less sensitive to
current harmonics.
OTHER CHARACTERISTICS
•
•
•
•
•
•
•
Sentry Multistandard is able to supply
loads with power factor from 0,8
capacitive to 0,8 inductive without
derating the active power (KW)
High level diagnostics: event log with
128 messages, states, measurements
and alarms - available from the built-in
LCD in several languages
Reduced noise levels: high frequency
inverter bridge
Back feed protection standard: to
avoid energy feeding back into the
mains supply (in compliance with CEI
11-20; DK5600)
Power factor correction (input power
factor, close to 1)
By pass may be deactivated to allow
operation as a frequency converter (at
50 or 60 Hz)
Emergency operation: the UPS can be
set to operate only when the mains
fails (for emergency lighting)
0,75
0,50
Active Power
100% kVA
Controls and settings menu.
0,25
-1
-0,8
-0,6
-0,4
-0,2
0
0,2
0,4
0,6
0,8
1
Reactive Power
ADVANCED COMMUNICATION
Language selection menu.
APPLICATIONS
• Compatible with PowerNetGuard for
remote maintenance
• Advanced, multi-platform
communication, for all operating
systems and network environments:
Watch&Save 3000 supervision and
shut-down software included, with
SNMP agent, for Windows 95, 98, NT
4.0, Me, 2000, 2003, XP, Mac OS
9.x, X, Linux, Novell operating
systems. The UPS is supplied with a
cable for direct connection to the PC
(Plug and Play)
• Double RS232 serial ports
• Network adapter slot for SNMP agent
• Emergency Power Off (EPO) shutdown
input contact
• Remote control mimic panel
• Local Area Networks (LAN)
• Data Centers
• Servers
• Industrial PLCs
• Cash registers
• Electromedical devices
• Emergency devices (lights/alarms)
• Telecommunication devices
• e-Business (Servers, Farms,
ISP/ASP/POP)
Battery voltages, internal operating
temperatures.
OPTIONS
Input isolation transformer
Active filter
LED remote status panel
LCD based remote control panel
Graphic Display remote control panel
Empty battery cabinet
for prolonged runtime
Additional battery charger
Dual input mains
UPS input current
with optional Active Filter
Sentry Multistandard with Active Filter
(internal view)
40/80kVA
40/80kVA
56
57
Three-phase input
Three-phase output
Three- / Single-phase input
Single-phase output
Sentry Multistandard
Sentry Multistandard
Input
Technical data
SM10
SM15
± 20%
Voltage range
230 Vac single-phase or 400 Vac three-phase + N
Rated voltage
Frequency range
SM20
SM10
SM15
ST10
Technical data
ST15
ST20
By pass
Rated power (kVA)
ST40
ST15
ST20
ST30
ST40
ST60
ST15
ST20
ST30
ST40
ST60
ST80
ST80
Lead, open vase acid and VRLA, AGM / GEL; NiCd
10
ST15
4-8 h
ST20
15
20
12
16
ST30
30
24
346 ÷ 422 Vac
Voltage regulation range
ST40
40
32
50 / 60 Hz selectable
Frequency
ST10
ST15
ST20
ST30
From 110 to 258 From 115 to 335 From 130 to 350 From 144 to 370
ST40
160
450x750x1200
ST60
60
48
ST60
180
ST80
80
64
ST80
192
500x740x1400
EPO and bypass
Remote controls
Volt free contacts
Remote signaling
O °C / +40 °C
<95% non condensing
Relative humidity
<56 dBA at 1 m
Protection degree
Efficiency
ST80
400 Vac
3+N
50/60 Hz
± 2% (selectable from ± 1% to ± 5%)
ST10
6h
ST10
8
3+N
380 - 400 - 415 Vac selectable
3:1
Crest factor (Ipeak/Irms)
± 1%
± 5% in 10 ms
110%125% 150% of the rated current for 5h/10’/1’
Overload
System
Weight (kg)
ST60
> 0.99
Sinewave absorbtion THDi <4% (3Ph input) (1)
ST10
Rated voltage
SM20
20
16/12 (2)
Active power
with load PF from 0,8 cap. to 0,8 ind. (kW)
Number of phases
Rated voltage
2%
Distortion with linear load
Static stability
Dynamic stability
SM20
From 125 to 345
Dimensions (wdh) (mm)
Volt free contacts
Remote signaling
Double RS232/C + remote contacts + communication interface slot
Communication
Operating temperature
Dark grey (RAL 7024)
Colour
Noise
IP20
> 92% in On-Line Mode, > 98% in Economy Mode/Smart Active Mode/Standby-Off Mode/AVS Mode
EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-89/336 EEC EN 62040-3
ST30
400 Vac three-phase + N
45 ÷ 65 Hz
Power factor
Current harmonic distortion
SM20
Batteries
Type
Recharge time
6h
SM15
15
200 ÷ 243 Vac
Voltage regulation range
SM15
From 110 to 330
± 15% (selectable from ± 5% to ± 25%)
Rated frequency
Permitted frequency range
SM20
Lead, open vase acid and VRLA, AGM / GEL; NiCd
SM10
10
Rated power (kVA)
12/10,5 (2)
1
230 Vac
3:1
Crest factor (Ipeak/Irms)
± 1%
± 5% in 10 ms
50 / 60 Hz selectable
Frequency
SM10
System
450x750x1200
EPO and bypass
Remote controls
O °C / +40 °C
< 95% non condensing
Dark grey (RAL 7024)
Colour
± 20%
Frequency range
> 0.99
Sinewave absorbtion THDi <4% (3Ph input) (1)
SM15
By pass
Number of phases
1
Permitted voltage range
± 15% (selectable from ± 5% to ± 25%)
50/60 Hz
± 2% (selectable from ± 1% to ± 5%)
SM10
Input
Rated voltage
Voltage range
45 ÷ 65 Hz
Power factor
Current harmonic distortion
230 Vac
Rated voltage
Number of phases
Permitted voltage range
Rated frequency
Permitted frequency range
Batteries
Type
Recharge time
Output
Output
8
Active power with load PF from 0,8 cap. to 0,8 ind. (kW)
Number of phases
Rated voltage
2%
Distortion with linear load
Static stability
Dynamic stability
110% 125% 150% of the rated current for 5 h/10’/1’
Overload
From 105 to 243
Weight (kg)
Dimensions (wdh) (mm)
Double RS232/C + remote contacts + communication interface slot
Communication
Operating temperature
Relative humidity
<56 dBA at 1 m
Noise
Protection degree
Efficiency
Compliance
<60 dBA at 1 m
IP20
> 92% in On-Line Mode, > 98% in Economy Mode/Smart Active Mode/Standby-Off Mode/AVS Mode
Compliance
EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-89/336 EEC EN 62040-3
(1) Version with Active Filter
(2) Version with single-phase input
59
58
Sentinel 7
Sentinel 7
Technical data
Models
S7-700
Power
S7-1000
700VA/560W
Input
S7-700
S7-1000 POWER
1000VA/800W
S7-1000
S7-1500
S7-1000 POWER
Nominal voltage
S7-1500
S7-3000
S7-2200
S7-3000 POWER
3000VA/2400W
S7-2200 POWER
S7-3000
S7-3000 POWER
140 Vac < Vin < 276 Vac @50% LOAD / 184 Vac < Vin < 276 Vac @ 100% LOAD
Maximum permitted voltage
300 Vac
Nominal frequency
50/60 Hz ± 5%
Power factor
> 0.99
Current distortion
δ7%
By pass
S7-700
S7-1000
S7-1000 POWER
Voltage tolerance
S7-1500
S7-2200
S7-2200 POWER
S7-3000
S7-3000 POWER
S7-3000
S7-3000 POWER
180 - 264 Vac
Frequency tolerance
Frequency selected (from ±0.Hz to ±5Hz configurable)
Output
S7-700
MAIN FEATURES
ADVANCED COMMUNICATION
Voltage distortion with linear load/with distorting load
• Filtered, stabilised, reliable output voltage:
on-line double-conversion technology (VFI
in accordance with IEC
62040-3) with built-in EMI filters
• High overload capability up to 150%
• Programmable auto-restart when mains
power returns
• Programmable cold-start from battery
• Power factor correction (UPS input
power factor close to 1)
• Wide input voltage tolerance (from 120280Vac) without battery usage
• Possibility to extend autonomy for several
hours
• Fully configurable using UPS Tools
configuration software
• High level of battery reliability (automatic
and manually-activated battery tests)
• High level of UPS reliability (total
microprocessor control)
• Low impact on the mains (sinusoidal
absorption)
• Input protection with fuse which can be
reset.
• Advanced communication, multiplatform,
for all operating systems and network
environments, Watch&Save 3000
supervision and shut-down software
included for Windows 7, 2008, Vista,
2003, XP, Linux, Mac OS X, Sun Solaris
and VMware ESX operating systems and
other Unix operating systems
• UPS Tools configuration and
personalisation software supplied as
standard
• RS232 serial port and opto-isolated
contacts
• USB port
• Slot for communication cards.
Frequency
S7-1000
S7-1000 POWER
S7-1500
S7-2200
S7-2200 POWER
< 2% / < 4%
Can be selected: 50 Hz or 60 Hz or self-learning
Static variation / Dynamic variation
± 1% / 5% in 20 msec.
Waveform
Sinewave
Current crest factor
3:1
On Line / ECO Mode and Smart Active efficiency
98%
Overload
2 min. (100%<Load<110%), 5 sec. (100%<Load<150%), 1 sec. (8>Load>150%)
Batteries
S7-700
S7-1000
S7-1000 POWER
Type
S7-1500
S7-2200
S7-2200 POWER
S7-3000
S7-3000 POWER
N.A.
2-4 hours
N.A.
S7-3000 POWER
VRLA AGM lead, maintenance-free
Charging time
2-4 hours
System
N.A.
2-4 hours
S7-700
S7-1000
S7-1000 POWER
S7-1500
S7-2200
S7-2200 POWER
S7-3000
Net weight (kg)
10,9
13,3
7
14,8
25,6
10,6
28
14
Gross weight (kg)
12,5
14,9
8,6
16,4
28,8
13,8
31,2
17,2
Dimensions (wdh) (mm)
422x235x158
Packaging dimensions (wdh) (mm)
500x340x245
Protection against overvoltages
446x333x190
585x470x325
300 joules
Protection devices
Overcurrent - short circuit - overvoltage - undervoltage - circuit breaker - excessively low battery
Communication
USB / DB9 with RS232 and contacts / Slot for communication interface
Standards
Safety: EN 62040-1 and Directive 2006/95/EC; EMC: EN 620040-2 category C2 and Directive 2004/108/EC
Ambient temperature / Relative humidity
0°C / +40°C / < 95% not condensed
Colour
Black
Noise level
< 40 dBA @ 1 m
Standard equipment
Power cable, serial cable, USB cable, safety manual, quick start, software on CD-ROM
Details
S7 2200-2200 POWER
power-off push-button feature to reduce
energy consumption to zero, when no load
is connected or switched off. Sentinel 7
models include 700VA,
1000VA, 1500VA, 2200VA and 3000VA.
S7-2200 POWER
2200VA/1760W
220-230-240 Vac
Voltage range for no battery intervention
Sentinel 7 is the latest evolution of the
successful Aros Sentinel 6 online UPS.
This latest development has been
designed with the environment in mind.
Sentinel 7 is an on-line double- conversion
UPS offering the highest levels of reliability
and protection for critical servers, voice
and data processing IT systems.
For long runtime applications, Sentinel 7
(POWER models) can be fitted with
matching battery extension packs
which also include additional battery
boost chargers.
In terms of communications, each Sentinel
7 has a built-in mimic panel with an LCD to
show input and output voltages, and
battery charge status.
The inverter is a totally new design, fully
microprocessor controlled and constructed
to achieve the highest levels of operating
efficiency and configuration options.
Sentinel 7 UPS also have USB
communication ports as standard, with a
built-in expansion slot for additional
adapters, protocol converters and relate
contact cards.
The UPS is highly efficient. Sentinel 7 is
designed to save energy and has a
S7-2200
1500VA/1200W
S7 3000-3000 POWER
Usb port
S7 700-1500
S7 1000-1000 POWER
Serial
Interface
Communication
slot
Battery
Expansion
connector
Thermal output
Protection
Output
Sockets
Input therm al
protection
Input socket
Sentinel 7 RT
REDUCED MANAGEMENT COSTS
Sentinel 7 RT is the high density version
of the Sentinel 7 range of doubleconversion on-line UPS. Sentinel 7 RT
is designed to power critical loads such
as servers, storage systems, telephone
equipment, medical systems and
industrial applications.
The UPS is ideal for Blade servers with an
input power factor close to Unity (1). The
UPS has can be used as tower UPS or
within a rackmount cabinet, and takes up
only 2U in height.
Sentinel 7 RT has a modern design, choice
of functional formats, and represents the
state-of-the-art technology
from the Aros research & development
team. The UPS can achieve an on-line
operating efficiency of 92%.
For critical business continuity
applications requiring long
runtimes, Sentinel 7 RT can be
installed with battery extension
packs (POWER models) with their
own internal battery chargers to
maintain sensible recharge times.
The UPS also incorporates the Aros
“power-off” function found in other UPS.
Sentinel 7 RT is designed to save energy
when no loads are connected.
SIMPLIFIED INSTALLATION
• Tower or Rackmount UPS: Sentinel 7
RT can be installed as tower or 19”
rackmount UPS, with a front mimic
panel that can be turned through 90º to
suit the installation.
• Noise Free Operation (<40dBA): the
UPS can be installed in any
environment thanks to its PWM
digitally-controlled high frequency
inverter.
• High Temperature Operation: UPS
components are sized for high
temperature operation up to 40ºC and
are not therefore stressed during normal
operational environments.
• EnergyShare: Sentinel 7 RT output
sockets can be programmed to
disconnect less critical loads when the
mains power fails.
Sentinel 7 RT can be programmed
remotely via software or set manually from
the front mimic panel to operate in a
range of energy saving operating modes:
• On Line: maximum power
protection and output voltage
waveform quality
• ECO: to increase operating efficiency to
98% and provide line interactive
protection
• Smart Active: with the UPS selecting
automatically its operating mode - ECO or
On-Line dependent upon the reliability
and quality of the local mains power
supply.
• Backup: for emergencies only with the
UPS only operating when mains power
fails
• Frequency converter: from 50 to
60Hz or 60 to 50Hz.
ADVANCED COMMUNICATION
• Sentinel 7 RT offers maximum
flexibility for integrations with any
communication system.
• Multiplatform communication for all
operating systems and network
environments, Watch&Save 3000
supervision and shut-down software
included for Windows 7, 2008, Vista,
2003, XP, Linux, Mac OS X, Sun
Solaris and VMware ESX operating
systems and other Unix operating
systems.
• UPS Tools configuration and
personalisation software supplied as
standard.
• RS232 serial port and opto-isolated
contacts.
• USB port
• Slot for communication cards such
as Modbus/Jbus, TCP/IP, SNMP and
relay contacts.
HIGH OUTPUT VOLTAGE QUALITY
• Even with distorting loads (IT loads
with a crest factor of up to 3:1).
• High short circuit current on bypass.
• High overload capacity: 150% from
inverter (even with no mains power).
• Filtered, stabilised, reliable (On Line
double conversion technology (VFI in
accordance with EN62040-2 class C1)
standard with filters to suppress
atmospheric disturbances.
• Load power factor correction:
incoming UPS power factor close to
1 and sinusoidal current absorption.
HIGH LEVELS OF BATTERY
RELIABILITY
• Automatic and manual battery tests
• Batteries are ‘hot-swappable’ and
user replaceable.
• Unlimited battery runtime extension
using battery extension packs.
OTHER FEATURES
• Output voltage can be selected using
software (220-230-240V).
• Auto-restart when mains power
returns (programmed via software).
• Stand-by on Bypass: when the
machine is switched off, it
automatically goes into bypass
operation with batteries charging.
• Power-Off with zero load connected
to save energy.
• Low battery warning
• Power-on delay
• Full microprocessor control.
• Automatic bypass without interruption
• Status, measurements and alarms
available on the front panel mimic
panel and LCD
• UPS firmware upgrade via PC platform
• Input protection including a user reset
thermal switch (up to 1500VA)
• Back-feed protection
• Manual option to switch to bypass.
Sentinel 7 RT
Models
Power
Sentinel 7 RT
Technical data
S7 RT-1000
S7 RT-1500
S7 RT-2200
S7 RT-2200 POWER
S7 RT-3000
S7 RT-3000 POWER
1000VA/900W
1500VA/1350W
2200VA/1980W
2200VA/1760W
3000VA/2700W
3000VA/2400W
System
Net weight (kg)
S7 RT-1000
S7 RT-1500
S7 RT-2200
17.5
18
30.5
15
31
15
21
21.5
35
19.5
35.5
19.5
Gross weight (kg)
Input
S7 RT-1000
S7 RT-1500
Nominal voltage
S7 RT-2200
S7 RT-2200 POWER
S7 RT-3000
S7 RT-3000 POWER
760x245x600
300 joules
USB / DB9 with RS232 and contacts / Slot for communication interface
Standards
50 Hz ± 5% / 60 Hz ± 5%
Power factor
> 0.98
Ambient temperature
Current distortion
δ7%
Relative humidity
Safety: EN 62040-1 and Directive 2006/95/EC; EMC: EN 620040-2 category C2 and Directive 2004/108/EC
O°C / +40°C
< 95% not condensed
Colour
By pass
S7 RT-1000
S7 RT-1500
Voltage tolerance
S7 RT-2200
S7 RT-2200 POWER
S7 RT-3000
S7 RT-3000 POWER
Frequency tolerance
Black
Noise level
< 40 dBA @ 1 m
Standard equipment
200 - 253 Vac
Power cable, serial cable, USB cable, safety manual, quick start, software on CD-ROM
Frequency selected (from ±0.Hz to ±5Hz configurable)
Details
Output
S7 RT-1000
S7 RT-1500
Voltage distortion with linear load/with distorting load
S7 RT-2200
S7 RT-2200 POWER
S7 RT1000
Can be selected: 50 Hz or 60 Hz or self-learning
Static variation
±1%
S7 RT1500
δ5% in 20 msec
Dynamic variation
Waveform
Input
Sockets
Sinewave
Current crest factor
3:1
On Line / ECO Mode and Smart Active efficiency
98%
S7 RT-1000
S7 RT-1500
Type
S7 RT-2200
S7 RT-2200 POWER
S7 RT-3000
S7 RT-3000 POWER
S7 RT-3000
S7 RT-3000 POWER
Input thermal protection
Emergency
switch device
(esd)
S7 RT2200/2200 POWER
Output
sockets
Battery
expansion
outlet
VRLA AGM lead, maintenance-free
Charging time
Overload times
S7 RT-3000 POWER
< 2% / < 4%
Frequency
Batteries
S7 RT-3000
2-4 hours
S7 RT-1000
S7 RT-1500
S7 RT-2200
S7 RT-2200 POWER
100% < Load < 110%
1 minute
110% < Load < 150%
4 seconds
Load > 150%
0,5 seconds
S7 RT-3000 POWER
Overcurrent - short circuit - overvoltage - undervoltage - circuit breaker - excessively low battery
Communication
50/60 Hz ±5Hz
Frequency range
600x245x550
Protection devices
300 V
Nominal frequency
625x450x87 (625x19"x2U)
Protection against overvoltages
140 Vac < Vin < 276 Vac @50% LOAD / 184 Vac < Vin < 276 Vac @ 100% load
Maximum permitted voltage
S7 RT-3000
425x450x87 (425x19"x2U)
Packaging dimensions (wdh) (mm)
220-230-240 Vac
Voltage range for no battery intervention
Dimensions (wdh) (mm)
S7 RT-2200 POWER
S7 RT3000/3000 POWER
Rs232
serial
Usb
Port
Input
plug
SENTINEL XR is the best solution for
protecting medium sized networking
applications which require the highest
possible levels of reliability. The UPS is
designed to support a wide applications
from IT to security. SENTINEL XR is
unique in that the UPS can be placed
directly onto the floor or mounted in 19”
rack mount cabinets. The range is
available in 3300-4000-5000-60008000-10000VA models. The UPS is
primarily an on-line double-conversion
(VFI) technology system with further
selectable operating modes that can
configure the UPS to protect
applications including emergency
lighting, security and medical systems.
Each UPS features advanced
communications and diagnostics
including a digital front panel display that
can turned to suit the installation format,
RS232 and USB interfaces, and an
internal adaptor slot for SNMP and other
interface card options.
Watch&Save 3000 software is supplied
as standard.
Sentinel XR
GUARANTEED OUTPUT QUALITY
• On line
• Economy Mode: selects Line
Interactive VI technology to power noncritical loads from mains and achieve
up to 98% operating efficiency
• Smart Active Mode: the UPS selects
automatically whether to operate in
On-line VFI technology - full system
protection or Line Interactive VI mode
depending on the stability of the mains
supply
• Emergency: the UPS can be
programmed to work only when the
mains fails - suitable for emergency
lighting
• Frequency conversion 50 or 60Hz
• The UPS can be installed as a floor
standing tower or 19” rack mount
UPS. The front panel digital display
can be pulled out (using the keys
provided) and rotated to suite the
installation format
• Low noise level (<40dBA) thanks to
the digitally PWM controlled ventilation
system which is load and temperature
dependent, and the use of an inverter
with a high switching frequency
(>20kHZ, above the audible range)
• Optional bolt-on maintenance bypass
(SENTINEL XR 5-6-8-10 kVA models)
to allow service without disruption to
the loads
• Performance guaranteed in
temperatures up to 40°C
• Two IEC output plugs with thermal
protection (SENTINEL XR 5-6-8-10
kVA)
• PowerShare output socket (2x10A
IEC) functionality on SENTINEL XR 56-8-10 kVA models
SELECTABLE OPERATING MODES
SIMPLIFIED INSTALLATION
• Even with typical distorting IT loads
with crest factors of 3:1
• Increased short circuit current on the
bypass
• Increased overload capacity: 150% on
inverter even when mains supply has
failed
• Reliable, filtered, stabilised and
regulated sinewave output (double
conversion technology VFI in
conformity with IEC 62040-3
specifications) with filters for
atmospheric disturbance suppression
• Rephasing of load as the UPS has an
input power factor close to 1, with a
sinusoidal input current
HIGHLY RELIABLE BATTERY
PERFORMANCE
• Automatic and manual battery tests
• Unique Low Ripple Current Discharge
(LRCD) to help prolong battery life
• Hot-swap user replaceable batteries
• Unlimited extendable back-up time
using modular design Battery
Extension Packs
• Increased ride through (without
batteries) on mains breaks up to 40ms
and for fluctuations ranging from 84 to
276Vac
OTHER CHARACTERISTICS
• Output voltage selection: 220-230240Vac
• Auto restart when mains power returns
programmed using the UPS Tools
software supplied
• Bypass on: when the UPS is switched
off, it automatically goes into bypass
mode to charge the batteries
• Automatic power down due to
minimum load
• End of battery discharge pre-alarm
• Delayed start up
• Completely digitally controlled
• Automatic bypass with no break in
power supply
• Use of IMS (Insulated Metallic
Substrates) modules
• Status, measurements, and alarms
available on the standard backlit
display
• UPS can be updated digitally (flash
upgradeable)
• Input protected by resettable thermally
activated switch
• Back-feed protection: to avoid current
being fed back into the mains should a
fault occur
• Manual switch over to bypass
• Microsoft Certified Product
ADVANCED COMMUNICATION
• Advanced, multi-platform
communication for all operating
systems and network environments:
Watch&Save 3000 supervision and
shut-down software included, with
SNMP agent, for Windows 95, 98,
NT4.0, Me, 2000, 2003, XP, Mac OS
9.x, X, Linux, Novell operating
systems. The UPS is supplied with a
communications cable for ’Plug and
Play’ PC connection
• Plug & Play feature
• USB port
• RS232 serial port
• Interface card slot
• Microsoft certification
APPLICATIONS
• Local Area Networks (LAN)
• Data Centers
• Servers
• Industrial PLCs
• Cash registers
• Electromedical devices
• Emergency devices (lights/alarms)
2-YEAR WARRANTY
LE FOR
SUITABY LIGHTING
NC
EMERGEPLICATIONS
AP
OPTIONS
Extended runtime solutions
with/without battery charger
External maintenance bypass
(except 3300VA and 4000VA)
Interface cards
Telescopic rails for rack cabinet
Display LCD custom
40
41
Sentinel XR
Technical data
Sentinel XR
Single-phase input
Single-phase output
Models
Power
Input
SXR-3300
3300VA/2300W
SXR-3300
SXR-4000
SXR-5000
4000VA/2400W 5000VA/3500W
SXR-4000
Rated voltage
SXR-5000
SXR-6000
6000VA/4200W
SXR-6000
SXR-8000
SXR-10000
8000VA/6400W 10000VA/8000W
SXR-8000
SXR-10000
220 - 230 - 240 Vac
50/60 Hz ± 5 Hz
Rated frequency
164 Vac @ load 100% 84 Vac @ load 50%
Minimum voltage
≤ 7%
Current distortion
> 0.98
Power factor
By pass
SXR-3300
Voltage range
SXR-4000
SXR-5000
System
Weight (kg)
SXR-8000
SXR-10000
SXR-4000
SXR-5000
SXR-6000
SXR-8000
SXR-3300
SXR-4000
SXR-6000
SXR-8000
38
SXR-4000
40
175x520x455
Dimensions (wdh) (mm) tower
SXR-5000
62
SXR-10000
SXR-6000
64
SXR-8000
80
175x660x455
92%
SXR-10000
85
2x175x660x455
483x660x175(4U)
On Line Efficiency
2x483x660x175(4U)
O °C / +40 °C
Overload - short-circuit - overvoltage - undervoltage - temperature - low battery
Protection
USB / RS232 + communication interface slot
Dark grey (RAL 7035)
Noise
SXR-10000
4-6h
SXR-5000
Output
< 95% non condensing
EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-89/336 EEC EN 62040-3
Compliance
Communication
Colour
Selected frequency ±5 % (user configurable)
SXR-3300
220 - 230 - 240 Vac selectable
Rated voltage
SXR-3300
483x520x175(4U)
Dimensions (wdh) (mm) rack
98%
Line-interactive/Smart Active Efficiency
Operating temperature
Relative humidity
SXR-6000
180 - 264 Vac (selectable in Economy Mode and SMART ACTIVE Mode)
Frequency range
Accessories provided
Batteries
Recharge time
1,5 %
Static variation
<40 dBA at 1 m
<45 dBA at 1 m
2x10A cables; 1xIEC-16A plug;
software; serial cable; plastic keys
to release display; handles kit
2 cable guides; terminal board connection; software; serial cable;
plastic keys to release display; handles kit
Details
USB port
Serial port
≤ 5% in 20 ms
Dynamic variation
Waveform
Interface card slot
SNMP or additional
RS232 ports
Sinewave
< 6%
Voltage distortion with non-linear load
< 3%
Voltage distortion with linear load
Input thermal
protection re-set
3:1
Crest factor
50/60 Hz selectable
Frequency
Overload capacity
SXR-3300
SXR-4000
SXR-5000
Input hardwired
gland
Output hardwired
glands
SXR-6000
4”
125% ≤ Load < 150%
4”
110% < Load < 125%
1’
100% < Load < 110%
Load > 150%
SXR-8000
Battery
extension pack
connector
SXR-10000
Input
cable access
Output
cable access
SXR 3300-4000
0.5”
SXR 5000-6000
SXR 8000-10000
42
43
Sentinel XR
Technical data
Sentinel XR
Three-phase input
Single-phase output
Models
Power
Input
SXR-6500
6000VA/5200W
SXR-6500
Rated voltage
SXR-8000
8000VA/6400W
SXR-8000
SXR-10000
10000VA/8000W
SXR-10000
400 Vac tree-phase + N
50/60 Hz ± 5 Hz
Rated frequency
164 Vac @ load 100% - 84 Vac @ load 50%
Minimum voltage
Power factor
By pass
Voltage range
SXR-8000
System
Weight (kg)
SXR-6500
64
SXR-6500
80
2x175x660x455
Dimensions (wdh) (mm) tower
92%
On Line Efficiency
SXR-10000
85
O °C / +40 °C
Relative humidity
SXR-10000
180 - 264 Vac (selectable in Economy Mode and SMART ACTIVE Mode)
Selected frequency ±5 % (user configurable)
SXR-8000
Batteries
SXR-8000
2x483x660x175(4U)
Dimensions (wdh) (mm) rack
98%
Line-interactive/Smart Active Efficiency
Operating temperature
> 0.95
SXR-6500
Frequency range
< 95% non condensing
EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-2004/108EC EN 62040-3
Compliance
Overload - short-circuit - overvoltage - undervoltage - temperature - low battery
Protection
Communication
USB / RS232 + communication interface slot
<45 dBA at 1 m
Noise
Dark grey (RAL 7035)
Colour
Accessories provided
4-6h
Recharge time
2 cable guides; terminal board connection; software; serial cable;
plastic keys to release display; handles kit
SXR-10000
Details
Output
SXR-6500
SXR-8000
1,5 %
Static variation
220 - 230 - 240 Vac selectable
Rated voltage
SXR-10000
Battery connection
≤ 5% in 20 ms
Dynamic variation
Waveform
Sinewave
< 6%
Voltage distortion with non-linear load
< 3%
Voltage distortion with linear load
3:1
Crest factor
50/60 Hz selectable
Frequency
Interface card slot SNMP
or additional RS232 ports
Serial port
USB port
Overload capacity
SXR-6500
SXR-8000
4”
110% ≤ Load < 150%
1’
100% < Load < 110%
Load > 150%
SXR-10000
Input cable access
0.5”
Output cable access
SXR 6500-8000-10000
44
45
Sentinel XR Plus
Sentinel XR Plus is the ideal solution for
powering vital mission critical, sensitive
loads such as electro-medical security
applications in order to guarantee
maximum reliability and availability.
The series includes 5kVA-6kVA
single/single phase and 6.5kVA-8kVA10kVA single/single phase and
three/single phase models and uses
double conversion on-line technology
(VFI). The load is powered constantly by
the inverter which supplies filtered,
stabilised and regulated sinewave voltage.
Moreover, the input and output filters
increase the immunity of the load against
mains power disturbances and lightning
strikes.
Sentinel XR Plus is without doubt one of
the best UPS systems on the market
today thanks to the technology used,
the features (selectable Economy Mode
and Smart Active Mode) and the
diagnostics offered (custom LCD display,
RS232 and USB interfaces complete
with Watch&Save 3000 software, EPO
contact and slots for optional interface
boards).
HIGH RELIABILITY
• Full microprocessor control.
• No break static and maintenance bypass.
• Features guaranteed up to 40 °C
(the components are designed to
operate at high temperatures and thus
are subject to less stress at ordinary
temperatures).
SELECTABLE OPERATING MODES
The operating mode can be
programmed using the software or
selected manually on the digital front
panel display.
• On line Mode (VFI).
• Economy Mode: increases efficiency
(up to 98%), and uses Line Interactive
(VI) technology to power low priority
loads from the mains supply.
• Smart Active Mode: the UPS automatically
decides which operating mode to use
(VI or VFI) depending on the quality of
the mains supply.
• Emergency Mode: the UPS can be
set to operate only when mains power
fails (emergency only mode).
• Frequency converter Mode
(50 or 60 Hz).
HIGH QUALITY OUTPUT VOLTAGE
• Even with distorting loads (IT loads
with crest factor of up to 3:1).
• High short circuit current on bypass.
• High overload capacity: 150% on
inverter, even when mains power fails.
• Filtered, stabilised and reliable voltage
(double conversion on-line technology,
VFI compliant with EN62040-3
specifications, with filters to suppress
atmospheric interference).
• Rephasing of the load: UPS input
power factor close to 1 with sinusoidal
current absorption.
48
SIMPLIFIED INSTALLATION
OTHER FEATURES
ADVANCED COMMUNICATION
• The UPS can be connected to both
single phase and three phase mains
supplies.
• Output terminal board + 2 IEC plugs
to power local equipment
(computers, modems, etc.).
• Easy to move thanks to built-in
wheels.
• Advanced diagnostics: status,
measurements and alarms available
on the custom LCD display.
• Very low noise level (<40dBA): for
installation in any environment thanks
to the PWM digitally controlled
ventilation that is load dependent, and
the use of an inverter with high
switching frequency (>20kHz, value
above the audible range).
• Autorestart when mains power
returns, can be programmed using
software or the digital front panel
display.
• Emergency mode: the UPS can be
programmed to work only when
mains power fails (suitable for
emergency lighting).
• Standard back feed protection: to
avoid current being fed back into the
mains system.
• Digital updating of the UPS
(flash upgradable).
• Compatible with the AROS
TeleNetGuard remote assistance
system.
• Advanced, multiplatform
communication for all operating
systems and network environments:
Watch&Save 3000 monitoring and
shutdown software included, for
Windows 2008, Vista, 2003, XP,
Mac OS X, Sun Solaris, Linux,
Novell and other Unix operating
systems.
• RS232 serial port.
• Plug and Play connection.
• Slots for communication interface
boards.
HIGH BATTERY RELIABILITY
• Automatic and manual battery tests.
• Low Ripple Current Discharge
system “LRCD” to prolong
battery life.
• Unlimited extendable runtime thanks
to dedicated modular design Battery
Boxes.
• Increased ride-through for mains
failures up to 40ms (high hold up
time) and for fluctuations in the input
voltage ranging from 84V to 276V).
LOW IMPACT ON MAINS POWER
• Sinusoidal input current on single
phase/single phase series.
APPLICATIONS
• Local Area Networks (LAN)
• Data Centers
• Servers
• Industrial PLCs
• Cash registers
• Electromedical devices
• Emergency devices (lights/alarms)
• Telecomunication devices
49
Sentinel XR Plus
Technical data
Models
XRMP 5000
XRMP 6000
XRTP 6500
XRTP 8000
XRTP 10000
Power
5000VA/4000W
6000VA/4800W
6500VA/5200W
8000VA/6400W
10000VA/8000W
Input
XRMP 5000
XRMP 6000
XRTP 6500
XRTP 8000
XRTP 10000
Rated voltage
220-230-240 Vac single-phase
Minimum voltage without battery intervention
220-230-240 Vac single-phase or 380-400-415 Vac three-phase with neutral
170 Vac @ load 100% / 140 Vac @ load 50%
Rated frequency
By pass
50/60 Hz ± 5Hz
XRMP 5000
Voltage range
XRMP 6000
Frequency range
Batteries
XRTP 8000
XRMP 5000
XRMP 6000
XRTP 6500
XRTP 8000
XRTP 10000
XRTP 8000
XRTP 10000
6-8h
XRMP 5000
Rated voltage
XRMP 6000
XRTP 6500
220 - 230 - 240 Vac selectable
Static variation
± 1,5 %
≤ 5% in 20 ms
Dynamic variation
Waveform
Sinewave
Voltage distortion with linear load
< 3%
Voltage distortion with non-linear load
< 6%
Frequency
50/60 Hz selectable or auto sensing
Crest factor
≥3:1
Overload capacity
100% < Load < 125%
125% ≤ Load < 150%
Load ≥ 150%
XRTP 10000
Selected frequency ±5Hz
Recharge time
Output
XRTP 6500
180 - 264 Vac (selectable in Economy Mode and SMART Mode)
XRMP 5000
XRMP 6000
SXRP 6500
SXRP 8000
SXRP 10000
1’
4”
0.5”
50
Sentinel XR Plus
System
XRMP 5000
XRMP 6000
XRTP 6500
XRTP 8000
XRTP 10000
Weight (kg)
89
90
91
94
95
Dimensions (wdh) (mm)
282x785x615
Efficiency Smart Mode
up to 98%
Operating temperature
O °C ÷ +40 °C
Humidity
< 95% non condensing
Protection
Overload - short-circuit - overvoltage - undervoltage - temperature - low battery
Compliance
EN 62040-1 EMC EN 62040-2 Directives 2006/95/EC - 2004/108 EC EN 62040-3
Communication
RS232 + USB + remote contacts + communication interface slot
Colour
Dark grey (RAL 7016)
Noise
<45 dBA at 1 m
Details
ON/OFF switch
Communication
interface slot
Emergency
power off (EPO)
Serial interface
port
IEC sockets
Input switch
(SWIN)
Battery fuse
holders (SWBT)
USB port
Maintenance
bypass (SWMB)
Output switch
(SWOUT)
51
SENTRY HPS HM/HT provides
maximum protection for vital ‘missioncritical’ networks, security applications
(electro-medical) and industrial
applications thanks to its outstanding
mechanical and electrical design.
The load is powered continuously by
the inverter with a filtered, stabilised
and regulated sinewave supply. The
input and output EMI filters
considerably increase the immunity of
the load to mains disturbances and
surges.
The SENTRY HPS HM/HT series uses
on-line double conversion technology
(VFI) with an isolation transformer on the
inverter output.
SENTRY HPS HM/HT is supplied with
Watch&Save 3000 software as
standard and can be remotely
monitored using the PowerNetGuard
system from anywhere in the world.
Additional battery extension packs
allow the standard battery runtime to be
extended up to several hours.
Sentry HPS
The Sentry HPS range features a wide
range of modules and configurations
that can be manufactured into one
complete system to solve your power
problems. Each system is therefore
unique and we ask that you consult our
engineers for your specific application.
• Sentry HPS can achieve efficiencies
>98% thanks to a selectable
Economy Mode which can be used
in stable electrical environments to
provide power supply continuity
should the mains fail.
• 0.8 power factor makes Sentry HPS
suitable for powering ICT and industrial
loads
• High level diagnostics: event log with
128 messages, states, measurements
and alarms - available from the built-in
LCD in several languages
• BACK FEED protection: to avoid
energy feeding back into the mains
supply should a fault occur
NO-BREAK POWER ARCHITECTURES
LOW CONSUMPTION LEVELS
OTHER CHARACTERISTICS
OPTIONS
MINIMUM IMPACT ON SUPPLIES EASY SOURSE
Input current distortion <4% for the
Sentry HPS with filter with sinusoidal
absorption to remove the risk of
resonance with other input supply
users or phase shift capacitor sets. The
absorbed current distortion is
independent of input supply
parameters such as impedance.
This enables Sentry HPS to deliver
maximum performance levels
regardless of the installation
environment. With these input features
Sentry HPS can achieve significant
savings in terms of sizing and power
supply sources - isolation transformers
and generators over less sophisticated
power systems.
MAXIMUM BATTERY CARE
SIMPLE TO INSTALL
• Capability to install the UPS into any
distribution system (neutral not
required on rectifier input)
• Capability to separate the
rectifier/bypass power networks and
to power these from two separate
sources, without Galvanic isolation
(necessary on UPS without an output
transformer)
HIGH RELIABILITY
• Extremely high short-circuit current to
ensure compatibility with the most
difficult transformer applications
(lighting, drives and industrial
processes) and an isolation
transformer on the inverter output
• Full microprocessor control with
no-break static and manual bypasses
• IGBT technology
• Battery deep discharge protection
• Temperature compensating charger
• Built-in automatic and manual battery
test feature
• Isolation transformers
• Various lead acid battery types
including 5 year, 10 year and 20 year
design life, VRLA, NiCad options and
runtimes up to several hours
• Communications software
• Solutions for low input current
distortion
• Closed loop parallel kit option (to be
ordered with the unit)
SPECIFIC SOLUTIONS
The UPS can be adapted to your
requirements. Please contact AROS
S.r.l. to discuss specific applications
and options.
MAXIMUM RELIABILITY
AND AVAILABILITY
• Connect up to 8 units in parallel or
N+1 redundancy, even of different
power ratings.
The UPS continue to work in parallel
even if one of the interconnecting
communication cables is
disconnected (CLOSED LOOP).
ADVANCED COMMUNICATION
• Compatible with PowerNetGuard for
remote maintenance
• Advanced, multi-platform
communication, for all operating
systems and network environments:
Watch&Save 3000 supervision and
shut-down software included, with
SNMP agent, for Windows 95, 98,
NT 4.0, Me, 2000, 2003, XP, Mac
OS 9.x, X, Linux, Novell operating
systems. The UPS is supplied with a
cable for direct connection to the PC
(Plug and Play)
• RS232 serial port
• Volt-free signal contacts
• EPO (Emergency Power Off)
shutdown input contact
• Input for switching to bypass by
remote signal
• LCD or LED-based remote
control panel
• Graphic Display Remote
Panel
• Generator interface:
enables desynchronisation
of the UPS output from a
generator supply which
may be subject to phase
and frequency variations.
The interface also enables
more economic use of the
battery charger.
APPLICATIONS
• Servers
• Local Area Network (LAN)
• Data centers
• Telecommunications
• Industrial equipment
• Electro-medical equipment
60
61
Sentry HPS
Fig 1- Bock diagram UPS in parallel up to 8 units
EXPANDABILITY
The units can be connected in parallel
up to 8 units to increase power
availability or redundancy.
The single module or the system can
be expanded any time to suit power
requirements without influencing the
initial investment.
Thanks to the peculiarity of the “Hot
System Expansion” feature, the
additional unit can be connected in
parallel while the other units are on-line
and supplying regular power to the
load. The new UPS is on-line and will
be set up automatically.
80 kVA
62
Three-phase input
Three-phase output
Three-phase input
Single-phase output
Sentry HPS
Sentry HPS
8
Power (kVA)
HM8
Models
Input
HM8
Technical data
HM10
10
HM10
HM15
15
HM15
Rated voltage
Voltage range
Frequency range
Power factor
Current harmonic distortion
Soft start
By pass
HM20
20
HM20
HM30
30
HM30
HM40
40
HM40
HM60
60
HM60
HM80
80
HM80
HM100
100
HM100
400 Vac three-phase
± 20%
45 ÷ 65 Hz
> 0.92 with harmonic filter
< 5% with harmonic filter
0-100% in 10”
HM8
HM10
Rated voltage
Permitted voltage range
Rated frequency
Permitted frequency range
Standard features
Batteries
HM15
HM20
HM30
HM40
HM10
HM15
HM20
HM30
HM40
HM60
HM80
HM100
HM8
System
HM10
10
8
HM10
HM15
HM20
HM30
HM40
HM100
HM20
HM30
290
HM40
340
Models
Power (kVA)
Batteries
HT10
10
HT10
HT15
15
HT15
HT20
20
HT20
HM60
440
HM80
80
64
HM80
520
HM100
100
80
HM100
650
1070x
740x1400
65 dBA at 1 m
>92%
Safety EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-89/336 EEC EN 62040-3
Yes
Yes
Yes
No
No
No
No
Inverter output
Rated power (kVA)
Active power (kW)
Number of phases
Rated voltage
Regulation of the output voltage
Crest factor (Ipeak/Irms)
Static stability
Dynamic stability
Frequency
Overload
Frequency stability
System
Weight (kg)
HT15
HT15
HT20
HT20
HT30
30
HT30
HT30
HT40
40
HT40
HT40
HT40
HT60
60
HT60
HT60
HT60
HT80
80
HT80
HT80
HT80
Maintenance-free lead-acid VRLA AGM/GEL; NiCd
0,2xC10
<1%
HT10
10
8
HT10
From 210
to 480
Dimensions (wdh) (mm)
Remote signaling
Remote controls
Communication
Operating temperature
Relative humidity
Colour
Noise
Protection degree
Efficiency
Compliance
Internal batteries
HT30
400 Vac three-phase
± 20%
45 ÷ 65 Hz
> 0.9 with harmonic filter
< 5% with harmonic filter
0-100% in 10”
HT10
400 Vac three-phase
± 15% (selectable from ± 10% to ± 25% from front panel)
50/60 Hz
± 2% (selectable from ± 1% to ± 5% from front panel)
BackFeed protection; split bypass line
HT10
Type
Maximum recharge current (A)
AC ripple voltage
HM60
15
20
30
40
60
12
16
24
32
48
1
230 Vac single-phase
220 ÷ 244 Vac phase/neutral (from control panel)
3:1
± 1%
± 5%
50/60 Hz configurable
110% 125% 150% of the rated current for 5h/10’/1’
± 0,05% on mains failure
± 2% (selectable from ± 1% to ± 5%) with mains supply present
HM15
800x740x1400
60 dBA at 1 m
By pass
Rated voltage
Permitted voltage range
Rated frequency
Permitted frequency range
Standard features
HM80
Maintenance-free lead-acid VRLA AGM / GEL; NiCd
0,2xC10
<1%
HM8
8
6.4
Weight (kg)
From 200
to 470
From 220
From 230
to 490
to 500
555x720x1200
Volt free contacts
EPO and Bypass
RS232 + remote contacts
O °C / +40 °C
< 95% non condensing
Light grey (RAL 7035)
54 dBA at 1 m
IP20
>91%
Yes
Input
Rated voltage
Voltage range
Frequency range
Power factor
Current harmonic distortion
Soft start
HM60
230 Vac single-phase
± 15% (selectable from ± 10% to ± 25% from front panel)
50/60 Hz
± 2% (selectable from ± 1% to ± 5% from front panel)
BackFeed protection; split bypass line
HM8
Type
Maximum recharge current (A)
AC ripple voltage
Inverter output
Rated power (kVA)
Active power (kW)
Number of phases
Rated voltage (V)
Regulation of the output voltage
Crest factor (Ipeak/Irms)
Static stability
Dynamic stability
Frequency
Overload
Frequency stability
From 190
to 460
Dimensions (wdh) (mm)
Remote signaling
Remote controls
Communication
Operating temperature
Relative humidity
Colour
Noise
Protection degree
Efficiency
Compliance
Internal batteries
HT15
HT20
HT30
HT40
HT60
15
20
30
40
60
12
16
24
32
48
3+N
400 Vac
348 ÷ 424 Vac phase/neutral (from control panel)
3:1
± 1%
± 5%
50/60 Hz configurable
110% 125% 150% of the rated current for 5h/10’/1’
± 0,05% on mains failure;
± 2% (selectable from ± 1% to ± 5%) with mains supply present
HT15
From 220
to 490
54 dBA at 1 m
HT20
HT30
From 230
From 282
to 500
to 552
555x720x1200
Volt free contacts
EPO and Bypass
RS232 + remote contacts
O °C / +40 °C
< 95% non condensing
Light grey (RAL 7035)
60 dBA at 1 m
IP20
> 90%
HT40
330
HT60
450
HT80
80
64
HT80
555
800x740x1400
62 dBA at 1 m
> 91%
> 92%
Safety EN 62040-1 EMC EN 62040-2 Directives 73/23-93/68-89/336 EEC EN 62040-3
Yes
Yes
Yes
No
No
Yes
No
No
64
65
The SPRING series includes models
from 500VA to 3000VA and uses
sinewave digital technology.
The SPRING range, with its advanced
communications and connectivity
options, is the ideal solution for the
most demanding of customers looking
for superior protection and versatility.
SPRING is the best protection for
network devices, rack mounted
servers, conventional rack-mounted or
tower servers, network storage
systems.
VERY HIGH PROTECTION
The Automatic Voltage Regulation
provides stabilisation from brownouts,
sag and surge voltages without making
use of the batteries.
Less frequent usage of the batteries
means that they will be fully charged
when really needed and last longer.
EMI filters then provide further
protection from spikes and transients.
When the mains power supply fails, the
load is powered by the inverter and
receives a true SINEWAVE supply for
maximum power continuity and
reliability.
The UPS also incorporates a protection
for PC and network, telephone
line/modem connections (RJ45-RJ11).
Spring
Spring
Models
S 500T
Technical data
S 800T
235x110x383
Dimensions (hwd) (mm)
800VA/540W
Power
Weight (kg)
500VA/350W
7,2
4 (10A)
IEC output sockets
1 (10A)
IEC mains input plug
S 1100T
1100VA/740W
S 1500T
S 2000T
11
1 (10A)
4 (10A)
S 2200RT
S 3000RT
1500VA/1050W 2000VA/1350W 2200VA/1540W 3000VA/2100W
235x160x425
10,6
1 (10A)
4 (10A)
18
1 (10A)
4 (10A)
18,4
1 (10A)
4 (10A)
88x582x438
31
32
1 (16A)
1 (16A)
8 (10A) - 1 (16A)
Input
160 V - 294 V
Voltage range
230 Vac
Rated voltage
Frequency
50/60 Hz auto sensing
Frequency range
• Advanced, multi-platform
communication for all operating
systems and network environments:
Watch&Save 3000
monitoring and shut-down software
included, with SNMP agent, for
Windows 95, 98, NT 4.0, Me, 2000,
2003, XP, Mac OS 9.x, X, Linux,
Novell and many other popular
operating systems
• USB or RS232 serial port (selectable)
• Slot-in SNMP network adapter card
• LCD display provides information
concerning alarms, status and
measure of the major electrical
parameters of input, output and
battery.
Powershare output socket provides the
load-shedding of the least critical load
to maximise the back up time of the
most critical servers.
Hot Swappable battery from the front of
the UPS allows easy and no-risks
maintenance of the UPS.
Additional Battery Box and extended
charging current are available in
2200RT and 3000RT for very long
back up time applications.
Predictive battery testing to spot
potential battery deterioration and
failure. Deep discharge protection to
reduce overall battery aging.
ADVANCED COMMUNICATION
HIGH AVAILABILITY
VERSATILITY
Spring (2200RT and 3000RT) can be
placed directly onto the floor or
mounted in 19’’ rack mount cabinets.
The front panel digital display can be
easily pulled out and rotated to suit the
installation format.
Tower and Rack versions includes
Emergency Power Off switch, which
allows to shutdown the output power in
case of emergency situations.
Cold start function enables Spring to
start up when power network is not
available.
± 5%
Output
Rated voltage
230 Vac (-5%, -10%)
True sinewave
Waveform
50 or 60 Hz auto sensing
Frequency
Batteries
Type
VRLA AGM Maintenance-free lead-acid
Recharge time
4-6 h
System
Protection
Overload - short-circuit - overvoltage - undervoltage - temperature - low battery
Communication
USB / RS232 / slot for interface communication
Safety compliance
IEC / EN62040-1-1 and Directive EEC 73/23
EMC conformance
IEC / EN62040-2 and Directive EEC 89/336
Performance
IEC / EN62040-3
Relative humidity
• Personal computers
• Small computers network
• Local Area Networks (LAN)
• Workstations
• Servers
• EPOS (Electronic Point Of Sales)
system
-15 °C - 45 °C
Storage temperature
APPLICATIONS
0 °C / + 40 °C
Operating temperature
< 95% non condensing
Noise
< 55 dBA
Details
USB port
2-YEAR WARRANTY
Serial
interface
port RS232
Slot for SNMP
network
adapter card
Output
sockets
IEC
Telephone/
it network
protection
OPTIONS
Battery box
(only 2200RT/3000RT)
Powershare
socket
Mains
input IEC
S 500T-800T-1100T
S 1500T-2000T
33
32
The SPRING series includes models
from 500VA to 3000VA and uses
sinewave digital technology.The
SPRING range, with its advanced
communications and connectivity
options, is the ideal solution for the
most demanding of customers looking
for superior protection and versatility.
SPRING is the best protection for
network devices, rack mounted
servers, conventional rack-mounted or
tower servers, network storage
systems.
VERY HIGH PROTECTION
The Automatic Voltage Regulation
provides stabilisation from brownouts,
sag and surge voltages without making
use of the batteries. Less frequent
usage of the batteries means that they
will be fully charged when really needed
and last longer. EMI filters then provide
further protection from spikes and
transients.
When the mains power supply fails, the
load is powered by the inverter and
receives a true SINEWAVE supply for
maximum power continuity and
reliability.
The UPS also incorporates a protection
for PC and network, telephone
line/modem connections (RJ45-RJ11).
Spring Rack
Spring Rack
Models
Power
Dimensions (hwd) (mm)
Weight (kg)
S 500R
Technical data
S 800R
500VA/350W
1U x 19” x 460
12
S 500R
Input
4 (10A)
IEC output sockets
1 (10A)
IEC mains input plug
800VA/540W
1U x 19” x 460
13,5
1 (10A)
4 (10A)
S 800R
S 1100R
1100VA/740W
2U x 19” x 582
15,6
1 (10A)
4 (10A)
S 1100R
ADVANCED COMMUNICATION
HIGH AVAILABILITY
APPLICATIONS
• Personal computers
• Small computers network
• Local Area Networks (LAN)
• Workstations
• Servers
• EPOS (Electronic Point Of Sales)
system
S 1500RT
230 Vac
Rated voltage
Output
2U x 19” x 582
31
1 (16A)
S 3000RT
3000VA/2100W
2U x 19” x 582
32,8
1 (16A)
8 (10A) - 1 (16A)
S 2200RT
S 3000RT
50/60 Hz auto sensing
± 5%
S 500R
S 800R
Rated voltage
S 1100R
S 1500RT
S 2200RT
S 3000RT
230 Vac (-5%, -10%)
True sinewave
Waveform
50 or 60 Hz auto sensing
Frequency
Batteries
S 500R
S 800R
Type
S 1100R
S 1500RT
S 2200RT
S 3000RT
VRLA AGM Maintenance-free lead-acid
Recharge time
System
S 2200RT
1500VA/1050W 2200VA/1540W
2U x 19” x 582
28,7
1 (10A)
8 (10A)
S 1500RT
160 V - 294 V
Voltage range
Frequency
Frequency range
• Advanced, multi-platform
communication for all operating
systems and network environments:
Watch&Save 3000
monitoring and shut-down software
included, with SNMP agent, for
Windows 95, 98, NT 4.0, Me, 2000,
2003, XP, Mac OS 9.x, X, Linux,
Novell and many other popular
operating systems
• USB or RS232 serial port (selectable)
• Slot-in SNMP network adapter card
• LCD display provides information
concerning alarms, status and
measure of the major electrical
parameters of input, output and
battery.
Powershare output socket provides the
load-shedding of the least critical load
to maximise the back up time of the
most critical servers.
Hot Swappable battery from the front of
the UPS allows easy and no-risks
maintenance of the UPS.
Additional Battery Box and extended
charging current are available in tower
2200 and 3000 for very long back up
time applications.
Predictive battery testing to spot
potential battery deterioration and
failure.
Deep discharge protection to reduce
overall battery aging.
VERSATILITY
Spring RT (tower 1500, 2200 and
3000) can be placed directly onto the
floor or mounted in 19’’ tower mount
cabinets.
The front panel digital display can be
easily pulled out and rotated to suit the
installation format.
Tower and rack versions includes
Emergency Power Off switch, which
allows to shutdown the output power in
case of emergency situations.
Cold start function enables Spring to
start up when power network is not
available.
4-6 h
S 500R
S 800R
Protection
S 1100R
S 1500RT
S 2200RT
S 3000RT
Overload - short-circuit - overvoltage - undervoltage - temperature - low battery
Communication
USB / RS232 / slot for interface communication
IEC / EN62040-2 and Directive EEC 89/336
EMC conformance
IEC / EN62040-1-1 and Directive EEC 73/23
Safety compliance
Performance
IEC / EN62040-3
-15 °C - 45 °C
Storage temperature
0 °C / + 40 °C
Operating temperature
Relative humidity
< 95% non condensing
Noise
< 55 dBA
Details
Output
sockets IEC
S 500R-800R-1100R
Powershare
socket
S 1500R
Output
sockets IEC
Mains input IEC
Powershare
socket
USB
Serial
port
interface
port RS232
OPTIONS
Battery box
(only 2200RT/3000RT)
EPO
Thermal
fuses
Output
sockets IEC
Telephone/it network
protection
S 2200R-3000R
Battery expansion
connector
Output sockets
IEC 16A
35
34
Stabilisers
The operating principle of an electronic
stabiliser is based on the regulation of
the voltage through self-transformer
sockets selected and connected to the
output via static switches.
Regulation is determined by a specific
electronic control circuit.
Advantages of using an electronic
stabiliser are:
• No harmonic distortion
• Insensitive to the type of load or
power factor
• Low weight/power ratio
• High reliability
• High voltage regulation speed.
Proper operation of most electric and
electronic equipment depends to a
large extent on the power supply
voltage that must be kept as steady
and as near to the nominal value as
possible. In many installations, the
mains power supply tends to fluctuate
for a number of reasons. So devices
that overcome and correct this problem
are often used and the ideal solution is
a stabiliser. AROS produces a full range
of electromechanical and electronic
stabilisers as well as electronic line
conditioners.
ELECTRONIC STABILISERS
WHY USE STABILISERS?
ELECTROMECHANICAL STABILISERS
This type of stabiliser controls the
voltage output by adding or removing
(by moving a brush converter) voltage
so as to restore output to the nominal
value. Advantages of using an
electromechanical stabiliser are:
• High quality voltage
• Insensitive to the type of load or
power factor
• Low weight/power ratio
• High stabilizing accuracy
• High reliability
• Wide range of power ratings for
single-phase or three-phase voltages.
ELECTRONIC LINE CONDITIONERS
An electronic line conditioner combines
an electronic stabiliser, an isolating
transformer and high attenuation
EMI/RFI filters in a single unit.
It provides maximum protection for
installations susceptible to voltage
fluctuations, high frequency line noise
and power surges. Advantages of the
line conditioners are:
• Isolation between the line
and the load
• No harmonic distortion
• Insensitive to the type of load
or power factor
• High voltage regulation speed
• Protection against power surges
• Protection against line noise.
77
Voltronic 4 single-phase
Voltronic 4 single-phase
Technical data
V4-500
V4-1000
Nominal output voltage
V4-2000
A LED panel provides information on:
• Mains input voltage exceeding
regulation limits
• Mains frequency exceeding limit
• Load level
• Overload
• Alarm for input overvoltage and/or
overheating (the visual alarm is
accompanied by an acoustic alarm).
V4-4000
V4-5000
V4-10000
220-230-240 Vac single-phase
Input voltage range
-18% +14% depending on the selected output voltage
Frequency
48 -62 Hz
2,4
Maximum output current at 230V (A)
0,5
Power (kVA)
1
2
4,5
4
9
18
±3%
Accuracy
98%
Efficiency
0 to 100%
Accepted load variation
2
Regulation speed (ms/V)
Load power factor
5
22
10
44
Any
Overload
The VOLTRONIC 4 single-phase
electronic voltage stabiliser is able to
adjust the output voltage within ±3% of
the rated voltage.
The main features of the VOLTRONIC 4
electronic voltage stabilisers are:
• Microprocessor full control
• Compact size
• High regulation speed
• High efficiency
• Insensitivity to load variations and
power factor.
1,5 IN x 5 sec
Harmonic distortion
<0,5%
Cooling
Natural
Forced ventilation
Operating ambient temperature
0°C ÷ 40°C
Mains OK, load level, overload, alarms
Display indications
IP 20
Protection degree
Acoustic alarm
Active for overload, over-voltage, over-temperature
Schuko socket
Output connection
Cable with Schuko plug
Input connection
Fuse
Output protection
Fuse
Input protection
V4-500
Dimensions (wdh) mm
Weight (kg)
Automatic switch
Fuse
Internal terminal board
Internal terminal board
V4-1000
V4-2000
V4-4000
180x215x194
9
V4-5000
230x350x275
10
21
V4-10000
340x540x310
25
27
51
78
79
Voltronic 4 three-phase
Voltronic 4 three-phase
Technical data
V4 3F-6000
Nominal output voltage
V4 3F-10000
A LED panel provides information on:
• Mains input voltage exceeding
regulation limits
• Mains frequency exceeding limit
• Load level
• Overload
• Alarm for input overvoltage and/or
overheating (the visual alarm is
accompanied by an acoustic alarm).
V4 3F-12000
V4 3F-15000
380/400/415 Vac + N selectable
Input voltage range
-18% +14% depending on the selected output voltage
Frequency
48 - 62 Hz
9
Maximum output current at 230V (A)
6
Power (kVA)
10
12
15
18
Independent on each phase
Regulation
±3%
Accuracy
98%
Efficiency
Regulation speed (ms/V)
15
22
2
Overload
1,5 IN x 5 sec
Accepted load variation
The VOLTRONIC 4 three-phase
electronic voltage stabiliser is able to
adjust the output voltage within ±3% of
the rated voltage.
Voltage stabilisation is performed
independently on each phase.
The main features of the VOLTRONIC 4
three-phase electronic voltage
stabilisers are:
• Microprocessor full control
• Compact size
• High regulation speed
• High efficiency
• Insensitivity to load variations and
power factor.
0 to 100%
Load power factor
Any
Harmonic distortion
<0,5%
Cooling
Natural
Forced ventilation
Operating ambient temperature
0°C ÷ 40°C
Mains OK, load level, overload, alarms
Display indications
IP 20
Protection degree
Internal terminal board
Output connection
Internal terminal board
Input connection
Fuse on each phase
Output protection
Automatic switch
Input protection
Active for overload, over temperature, irrecoverable failure
Acoustic alarm
V4 3F-6000
V4 3F-10000
Dimensions (wdh) (mm)
Weight (kg)
V4 3F-12000
V4 3F-15000
340x540x310
44
48
52
60
80
81
ELC Line Conditioners
ELC Line Conditioners
Technical data
ELC 1500
guarantee and effective protection as
they combine an electronic stabilizer,
EMI/RFI filters and an isolating
transformer in a single unit.
The equipment is controlled by a
microprocessor logic that also sounds
alarms in the event of overloads,
overvoltage or overheating.
ELC 3000
220/230/240 Vac selectable, single-phase
Nominal output voltage
220/230/240 Vac single-phase
Nominal input voltage
Input voltage range
ELC 5000
-18% +14% depending on the selected output voltage
Input frequency
Power (kVA)
Max. output current at 230V (A)
48 - 62 Hz
1,5
3
7
5
14
±3%
Accuracy
95%
Efficiency
Regulation speed (ms/Volt)
22
2
Overload
1,5 IN x 5 sec
Accepted load variation
The electronic line conditioners of the
ELC range have been specially
designed to protect electronic control
equipment such as PC’s, PLC’s,
internet devices, laboratory
instrumentation, data transmission and
audio-video apparatus, against
anomalies or interference in the power
supply circuit. In particular, ELC protect
against line noise and power surges
ensuring effective voltage regulation.
The electronic line conditioners
0 to 100%
Load power factor
Any
Harmonic distortion
<0,5%
70 dB
Common mode rejection ratio
Up to 4KV - 130 Joule
Input peak voltage protection
Primary and secondary insulation voltage
2500V input/output
Cooling
Natural
Operating ambient temperature
Forced ventilation
0°C ÷ 40°C
Line OK, load level, overload, alarms
Display indications
IP 20
Protection degree
Acoustic alarm
Active for overload, overvoltage, overtemperature
Internal terminal board
Output connection
Internal terminal board
Input connection
Fuses
Output protection
Automatic switch
Input protection
ELC 1500
Dimensions (wdh) (mm)
Weight (kg)
ELC 3000
230x350x275
ELC 5000
340x540x310
26
44
56
82
83
RQ
RQ
Power (kVA)
Input voltage range
mains nor by the value and load power
factor; the output power distortion is
very low (<0,2%) and the total
efficiency is very high. The installation
of the RQ stabilizers is very flexible:
their special shape makes it easy to
install them near the equipment to
power or inside it. They can be
mounted on the wall or in a cabinet.
Technical data
2,5 / 2
1
RQ 2500
RQ 1000
±25%
18
Regulation speed (ms/Volt)
4
Maximum output current (A)
Efficiency
94%
±15/20%
11
18
96%
±15/20%
Input voltage range
15 / 10
10 / 7,5
Power (kVA)
RQ K15
RQ K10
18
Regulation speed (ms/Volt)
44
Maximum output current (A)
Efficiency
The RQ stabilizers belong to the
electromechanical series with electronic
control. They provide a perfect
constant single-phase output voltage
completely independent from any
variation of the input voltage within the
accepted voltage range.
The stabilisation of the output voltage
is not affected neither by eventual
harmonic distortion present in the
96%
±15/20%
65
18
98%
RQ 5000
5/4
±15/20%
22
18
97%
RQ K25
25 / 18
±15/20%
109
20
98%
RQ 7000
7 / 5,5
±15/20%
31
18
98%
RQ K35
35 / 26
±15/20%
152
20
98%
Common characteristics
Nominal input/output voltage
230 Vac
Accuracy
±1%
0 to 100%
Load variation
50/60 Hz
Nominal frequency
Load power factor
Any
Harmonic distortion
<0,2%
Cooling
Natural
Operating ambient temperature
-5°C ÷ 40°C
Protection degree
Dimensions (wdh) (mm)
Weight (kg)
Dimensions (wdh) (mm)
Weight (kg)
IP 21
275x425x260
275x425x260
RQ 2500
RQ 1000
19
RQ 5000
275x425x260
22
28
300x565x280
300x565x280
RQ K15
RQ K10
50
RQ K25
405x670x1150
55
125
RQ 7000
300x565x280
42
RQ K35
405x670x1150
130
85
84
Tristab-T
Tristab-T
provided on the average value of threephases and then these stabilizers are
suitable for maximum 50% unbalanced
load. There is the possibility of
choosing between two input voltage
ranges according to the nominal power
required (see table).
The operator panel includes a digital
voltmeter which inform on the status of
the line downstream on the voltage of
each phase and the linked voltages.
All models (up to 60kVA) are provided
with wheels for an easier positioning
and handling.
Technical data
4
Power (kVA) with input ±20%
10
5
Power (kVA) with input ±15%
T10
T5
Input voltage range
7,5
60
Power (kVA) with input ±20%
105
75
Power (kVA) with input ±15%
T105
T75
96%
95%
Efficiency
18/13
18/13
Regulation speed (ms/Volt)
14
7
Maximum output current (A)
±15/20%
±15/20%
Input voltage range
TRISTAB-T series includes several
voltage stabilizers of electromechanical
type with electronic control. They
provide a perfect three-phase output
voltage completely independent
from any variation of the input voltage
within the accepted voltage range. The
stabilisation of the output voltage is not
affected neither by eventual harmonic
distortion present in the mains nor by
the value and the load power factor;
the distortion of the output voltage is
very low (<0,2%); the total efficiency is
very high. The voltage regulation is
18/13
18/13
Regulation speed (ms/Volt)
150
107
Maximum output current (A)
±15/20%
±15/20%
T15
15
12
±15/20%
21
18/13
97%
T135
135
80
98%
98%
Efficiency
105
±15/20%
193
18/13
98%
T20
20
15
±15/20%
28
18/13
98%
T175
175
135
±15/20
253
18/13
98%
T30
30
24
±15/20%
43
18/13
98%
T230
230
175
±15/20%
332
20/18
98%
T50
50
36
±15/20%
71
18/13
98%
T60
60
45
±15/20%
87
18/13
98%
T300
300
230
±15/20%
433
20/18
98%
Common characteristics
Nominal input/output voltage
400 Vac
Accuracy
±1%
Nominal frequency
50/60 Hz
Load variation
0 to 100%
Load power factor
Any
Harmonic distortion
<0,2%
Cooling
Forced ventilation
Operating ambient temperature
-5°C ÷ 40°C
Protection degree
IP 21
T5
Dimensions (wdh) (mm)
Weight (kg)
T10
T15
T20
360x520x1000
50
T75
Dimensions (wdh) (mm)
Weight (kg)
T30
T50
405x670x1150
60
T105
605x800x1400
320
110
T135
605x800x1600
480
120
T175
160
T230
T60
605x800x1400
200
250
T300
605x850x1650 1210x800x1600 1210x850x1700
500
700
800
1200
86
87
Tristab-Y
Tristab-Y
useful with unbalanced three-phase
loads or single-phase loads.
For proper operation, the presence of
the neutral wire is necessary. There is
the possibility of choosing between two
input voltage ranges according to the
nominal power required (see table).
The operator panel includes a digital
voltmeter which provides information on
the voltage of each phase and the
linked voltages. All models (up to
60kVA) are provided with wheels for an
easier positioning and handling.
Technical data
4
Power (kVA) with input ±20%
10
5
Power (kVA) with input ±15%
Y10
Y5
Input voltage range
7,5
105
75
Y105
Y75
96%
95%
Efficiency
18/13
18/13
Regulation speed (ms/Volt)
14
7
Maximum output current (A)
±15/20%
±15/20%
60
Power (kVA) with input ±20%
Power (kVA) with input ±15%
Input voltage range
TRISTAB-Y series includes several
voltage stabilizers of electromechanical
type with electronic control from 5 to
300kVA. They provide a perfect threephase output voltage completely
independent from any input voltage
variation within the accepted voltage
range.
The stabilisation of the output voltage
is not affected neither by eventual
harmonic distortion
present in the mains nor by the value
and load power factor; the output
voltage distortion is very low (<0,2%);
the total efficiency is very high. In the
"Y" version the stabilising effect is
obtained independently on each phase.
This solution is therefore particularly
18/13
18/13
Regulation speed (ms/Volt)
151
107
Maximum output current (A)
±15/20%
±15/20%
Y15
15
12
±15/20%
21
18/13
97%
Y135
135
80
98%
98%
Efficiency
105
±15/20%
193
18/13
98%
Y20
20
15
±15/20%
28
18/13
98%
Y175
175
135
±15/20%
253
18/13
98%
Y30
30
24
±15/20%
43
18/13
98%
Y230
230
175
±15/20%
332
20/18
98%
Y50
50
36
±15/20%
71
18/13
98%
Y60
60
45
±15/20%
87
18/13
98%
Y300
300
230
±15/20%
433
20/18
98%
Common characteristics
Nominal input/output voltage
400 Vac
Accuracy
±1%
Nominal frequency
50/60 Hz
Load variation
0 to 100%
Load power factor
Any
Harmonic distortion
<0,2%
Cooling
Forced ventilation
Operating ambient temperature
-5°C ÷ 40°C
Protection degree
IP 21
Y5
Y10
Dimensions (wdh) (mm)
Weight (kg)
Dimensions (wdh) (mm)
Weight (kg)
Y15
Y20
360x520x1000
70
Y30
Y50
405x670x1150
75
110
605x800x1600
605x800x1400
Y135
Y75
Y105
350
540
580
145
Y175
170
Y230
Y60
605x800x1400
190
260
Y300
1210x800x1600 1210x850x1700
610
900
1200
88
89
The SYNCRO series includes the 8002000VA models and uses digital
technology. The load is powered from
the mains through an AVR to stabilise
brownout, sag and surge voltages, and
EMI filters to suppress spikes and
transients.
When the mains fails, the load is
powered by the inverter with a pseudo
sinewave to provide sufficient runtime
for computer system shutdown using
the Watch&Save 3000 software
supplied as standard. The UPS also
incorporates a filtered socket for PC
network and telephone line cable
protection.
Syncro
Syncro
Models
Power
Input
Technical data
Syncro 800
800VA/480W
Syncro 800
Syncro 1000
1000VA/600W
Syncro 1000
ADVANCED COMMUNICATION
CHARACTERISTICS
Syncro 1500
1500VA/900W
220-230-240 Vac
Rated voltage
Syncro 1000
Syncro 1500
230 Vac (-8%, +10%)
Syncro 2000
2000VA/1200W
Syncro 2000
Pseudo sinewave
Syncro 800
Syncro 1000
Syncro 1500
Syncro 2000
Maintenance-free lead-acid VRLA, AGM
6-8 h
Syncro 800
14
Syncro 1000
Syncro 1500
14.5
15
140x375x180
Dimensions (wdh) (mm)
Safety compliance
APPLICATIONS
Syncro 2000
50/60 Hz auto sensing
Syncro 800
Voltage on mains operation
50 or 60 Hz (± 0.5%)
2 ms
Waveform on battery operation
Batteries
Type
Recharge time
System
Weight (kg)
Battery low - overcurrent - short-circuit
Protection
Tel/Modem protection
Syncro 2000
20
140x410x214
RJ45 connectors
Communication
EMC conformance
• Personal computers
• Small computers network
2-YEAR WARRANTY
Syncro 1500
230 Vac (±25%)
Voltage range
Frequency
Output
230 Vac (± 5%)
Voltage on battery operation
Frequency on battery operation
Transfer time
• High level multi-platform
communication for all operating
systems and network environments:
Watch&Save 3000 monitoring and
shut-down software included, with
standard integrated SNMP agent, for
Windows 95, 98, NT 4.0, Me, 2000,
2003, XP, Mac OS 9.x, X, Linux,
Novell operating systems
• The UPS is supplied with a
communications cable for ‘Plug and
Play’ PC connection
• Mains power supply stabilisation and
filtering (technology with AVR and
filters for atmospheric disturbance
suppression)
• Cold start capability: the UPS can
power up without a mains supply
present
• Auto restart at power-up
• Integrated protection for PC networks
and telephone line/modem
connections RJ11
• High reliability with built-in automatic
battery test feature
For advanced communication and top
flight performance, SYNCRO is the
ideal solution for small network users
requiring total control of their power
system.
RS232 port
EN 62040-1-1 and Directive 73/23, 93/68 EEC, EN 62040-3
EN 62040-2 and Directive 89/336, 192/31 EEC, 93/68 EEC
Surge capability
IEC 801-5
Noise
< 40 dBA at 1 m
Colour
Dark grey
Operating temperature
0 °C / +40 °C
Storage temperature
-15 °C / +45 °C
Relative humidity
< 95% non condensing
Details
Serial interface
port
Telephone line/
modem protection
Output sockets
Mains input
Syncro 800-1000-1500
Syncro 2000
31
30