HOUSING: 801-NON I.C.
LAMP MODULE: A-TUNGSTEN HALOGEN
526 Portal Street
Cotati, CA 94931
USA
Project Name
P 707.794.0888
Date
F 707.795.4379
Type
www.8lighting.com
Prepared By
All No. 8 Lighting fixtures and components are UL/CSA listed.
Models 801/A & 801/B also CE listed. U.S. Patents Pending on
the SeamlessTM and InsetTM Series trims as well as the type A Lamp
Module. No. 8 Lighting reserves the right to change details of
design, materials, and finish.
Comments
Catalog #
801 / A –
–
/
© 2014 No. 8 Lighting
Doc # 91101-06
–
PRODUCT FEATURES
Housing
• Type Non-IC for new construction installations where insulation can be kept a minimum of 3” away from all sides.
• Accepts all Number Eight Lighting Lamp Modules and Trim Assemblies.
• All aluminum construction for maximum heat dissipation and corrosion prevention.
• Features cross-hair graphics for precise alignment during rough-in installation.
• Extra large capacity junction box with (3) 1/2” knock-outs, (2) 3/4” knock-outs, and (1) 3/8” knockout.
Junction box is UL listed for through wire branch circuiting and is accessible from below after installation.
• Extra rigid bar hangers with four lock down points and integrated self tapping fasteners which accommodate wood or metal joists w/ on center spacing of 12”-24”. Bar hangers can be mounted to either
sides or ends of housing depending on installation requirements.
5-3/4”
4-3/4”
14”
Lamp Module
• Low voltage MR-16/50 watt maximum*. Accepts all MR-16 lamp styles and up to two optical accessories.
• All aluminum construction for maximum heat dissipation and corrosion prevention.
• Features unique gear driven adjustment mechanismw/optical quality machined components for tool free
adjustment.
• Lamp holder position optimized for true 0-45° vertical adjustment, and 365° horizontal. Both vertical and
horizontal adjustments include tool-free locking to ensure aiming/adjustment remains unaffected during
re-lamping.
• Easily removed for servicing or to be interchanged with other Number Eight Lighting lamp modules.
*37 watt maximum when used with 802 IC housing and lensed trim plate.
9-1/2”
801 - NON I.C. HOUSING
Transformer/Socket Assembly
• QT - Integral Q-TranTM toroidal transformer with choke (rated max. 19db). Features dual-tap primary
inputs for 100% light output when used with a switched or dimmed circuit. Rated output of 12 volts.
• ET - Integral electronic transformer*. Rated output of 11.7 volts.
• RT - Remote transformer (supplied by others).
• High quality porcelain socket (GX5.3 base) with 14” 18 AWG/ 250°C PTFE leads. Thermally protected
to prevent overheating from mis-lamping or installing insulation too close.
• Transformer removable and accessible from below after installation.
*37 watt maximum when used with 802 IC housing.
A - TUNGSTEN HALOGEN LAMP MODULE
Use for general, accent, and wall wash lighting
applications. Features 0-45 degree adjustable
aiming angle.
PRODUCT SPECIFIER/PRODUCT ORDER NUMBER
801
/
A
–
HOUSING
/
LAMP
MODULE
+
–
TRANSFORMER
QT
Q-TRANTM
Integral toroidal magnetic
transformer w/ choke
(19 db sound rating)
801
New Construction –
NON-I.C.
9 1/2”W x 14”L x 5 3/4”H
Accepts All No.8 Lighting
Lamp Modules.
Insulation must be kept
a minimum of 3” away
from all sides.
A
LOW VOLTAGE, MR-16
(12 volt/50 watt maximum)*
Lamp supplied by others.
45° tilt, full 360° rotation
with locking vertical and
horizontal adjustment.
Includes clear glass lens.
*37 watt maximum when
used with 802 IC housing
and lensed trim plate.
ET*
Integral electronic
transformer
*37 watt maximum when
used with 802 IC housing.
RT**
REMOTE TRANSFORMER
**12 volt transformer for
low voltage MR-16 type
lamp required (supplied
by others).
+
/
VOLTAGE
12V (RT only)*
120V (Standard)
230V (QT only)**
240V (ET only)**
277V (QT only)*
*Non-standard voltage.
Additional lead time may
be required.
–
LAMP MODULE
OPTIONS
/
ADDITIONAL
OPTIONS
+
SF
TBC
LS
LINEAR SPREAD lens
(Set of four) included with
housing.
LSF
PMB
SOFT FOCUS lens
FROSTED
LINEAR SPREAD lens
T-BAR MOUNTING CLIPS
PANEL MOUNTING
BRACKETS
(Set of two) included with
housing.
**CE certified for markets
outside of U.S.
Additional lead time may
be required.
91101-06 PAGE 1