2016
Operating and Service Manual
For Amtech Wall Mount Tables
0800 268 324
www.amtech.co.nz
PRE-DELIVERY
AND INITIAL
SETUP
1. Ensure when product arrives that there has been
no transit damage, taking particular care of
electrical, framework, powder coating damage
and mattress damage. Amtech accept no claim
against pre-delivery damages once the products
has been delivered and signed as received in
good order and condition.
2. Plug table in to mains powered 240V plug and switch on (if battery power pack, charge battery
as per instructions for 24 hours as per guidelines).
3. Rechargeable Battery Systems – 24 hour full
uninterrupted charge is initially required before
operating table. (See charging instructions in
the manual.)
2
3
4
7
8
9
10
11
12
13
CONTENTS
PRE-DELIVERY & INITIAL SET UP
INTENDED USE
INSTALLATION INSTRUCTIONS
OPERATING INSTRUCTIONS
IMPORTANT POINTS
MAINTENANCE INSTRUCTIONS
ELECTRICAL SAFETY
BATTERY RECHARGING
ACCESSORIES
WARRANTY
Thoroughly read this manual before commencing installation and operation.
It is critical that the suitability of the correct
model Ergosol Wall Mount Table is installed.
WET AREA
PRODUCT RANGE
•Designed for primary use as a changing
table and designed for limited showering
/ bathing activities only
•Coating is a 3-process powder coat finish
•Fitted with a 240 watt mains IP66
standard actuator / motor system.
WET AREA
PRODUCT RANGE
Installation must be in
accordance of Amtech
Medical instructions for
The ordered Ergosol Wall Mount Changing Table will come
completely assembled and only wall mounting installation is required.
mounting an Ergosol Wall
1. An experienced and qualified builder must install any Ergosol Wall
Mount Change Table.
2. Liability Disclaimer
Amtech accepts no liability for any injury sustained through faulty
installation. It is the responsibility of the installer to ensure the
table is securely fixed to a solid wall.
per following drawings
Mount Change Table as
and specifications
(applicable for New
Zealand).
To achieve the recommended
height range for height
adjustable models (of 550mm to
850mm), mount the table at the
recommended height position.
Mattress
Wall
!
INSTALLATION
INSTRUCTIONS
IMPORTANT
INTENDED USE
•Designed for use in a
shower / bath application
•Coating is polished stainless
steel 304 grade
•As used for showering / bathing,
recommended to only use with 12
volt IP65 battery pack actuator /
motor system
•Supplied with Link rechargeable
battery pack standard (IP65 rated).
150kg
Loading Rating
This bed is designed and
only allowed for a 150kg
safe working load.
Floor
NB: removal of pin which holds
bottom of actuator in pace will
need to be temporarily removed
to allow screw / bolt mounting
into wall.
Electrical Installation – 240
watt mains power only
If unit is purchased with a 240
volt (mains powered) actuator
programme, then a 3 pin power
outlet with RCD safety control
is required. Length of cord with
plug is 1 metre.
Mount the plug as far away as
possible from any water source,
and in accordance with any local
electrical safety standards and
recommendations. Product can
be hard wired as an option.
OPERATING
INSTRUCTIONS
MAINTENANCE
INSTRUCTIONS
Up/Down Operation
Mechanical/Framework
Electrical
On the hand held control switch, simply push the up
or down button (↑ or ↓) to raise or lower the bed.
There is very little mechanical maintenance required,
just occasionally lightly oil the guides and plastic
inserts to keep the movement smooth and free.
Either oil or silicone spray can be used.
The electrical components are sealed and have no
user serviceable parts. Any problems should be
reported to Amtech Medical in the first instance as
unauthorised attempts to carry out repairs will break
the seal and may void the warranty. It is advised that
an electrician or electrical service technician holding a
current practicing license carry
out the electrical safety check as recommended by
the Electrical Workers Registration Board and OSH
every 12 months.
Fold Away Table Top
The unit is designed for the padded top and frame to
be folded away upright when not in use.
To raise the top, gently lift the padded top to upright
position. It will remain in this position (held by a gas
strut) until lowering is required.
To lower, simply pull down gently until top comes to
rest at correct position.
The bolts and nuts holding the table together are
locked but an occasional check should be prudent.
Cleaning
The padded top and frame of the table should be
kept clean from soap build up and other deposits,
warn soapy water is adequate for this. DO NOT use
harsh abrasives or strong acid or alkaline cleaners.
The Linak Actuator System can be cleaned with brush
and low water pressure cold water in the retracted
static position only ie, not moving.
ELECTRICAL
SAFETY
The Linak Actuator Systems are built and supplied
to International Safety Electrical Ratings known as
“International Protection” (IP).
Full Linak technical information is available from
Amtech Medical directly upon request. Detailed
specifications from Linak are available on request.
All Ergosol Wall Mount Changing Tables are Linak
Important Points
Patients & Side Safety Rails
If the patient is restless and is inclined to move on
the table, it is highly recommended that an Ergosol
side safety rail is installed on the unit. This available
accessory will safely ensure patient cannot roll off side
of bed.
Items which may damage padded top
Supplied with this table is a high specification
waterproof padded top. Ensure that the top is not
able to be damaged by the patient or care givers
sharp objects (ie, watches, belts, etc). position.
actuators specified to IP66, which represents dusttight protection and protection against water
washing, limited ingress permitted, in accordance with
Linak’s test procedures.
Depending on geographical area, legal consent may
be required on electrical safety switch/s for 240 volt
system.
BATTERY RECHARGING
Operation and Care
(This option, only if fitted)
The Linak battery system operates at a nominal
24VDc to reduce any risk of electrical discharge to
the operator or patient. An emergency stop button is
fitted to the battery system.
The battery is mounted at the bottom of the main
frame and is a split unit allowing the battery to be
removed for recharging.
The charger can be set in another room and the
battery taken to it, the battery should ideally be
charged every 24 hours, this will extend the battery
life. It is important that the battery is not fully
discharged at any time.
To remove or replace the battery to the table is best
done with the mattress in the folded up position.
The battery is designed to simply snap into the
mounting bracket and is easily released by pulling
on the handle on the battery pack towards you.
Use both hands to support the battery pack when
removing or replacing it.
The wall charger has a light to show the power is
connected (turned on) and a second light to show
it is charging the battery. When the battery is fully
charged, the second light goes out.
The control box on the bed does not have any
lights to indicate battery condition.
ACCESSORIES
A range of accessories is available for all Ergosol tables. Specific accessories are noted below.
WARRANTY
Component Warranty
All framework provided correct specification
and used in correct environment.
Frame 5 years
Actuators and Systems (excludes batteries)
3 years
Castors 2 years
Upholstery1 years
Warranty Conditions
Amtech Medical guarantees quality of all parts supplied by
us or our agents for the suitable usages and corresponding
periods specified above.
Amtech will replace free of charge any faulty part returned
to us freight paid, which bears no evidence of mishandling,
overloading, repairs or alteration made by the user /
purchaser without our written consent.
For claims under this warranty, contact in the first instance
should be to the distributors from whom the equipment
was purchased, or Amtech Medical if purchased direct.
The warranty applies to the original purchaser only, and
requires proof of purchase via production of the original
invoice.
We recommend you keep the invoice with this material
for future reference. Please keep in a safe place.
Disclaimer
Amtech Medical accepts no liability or responsibility for any
injury sustained through faulty installation or useage of any
Ergosol product. It is the responsibility of the purchaser to
ensure that correct installation procedures were carried out
for initial set up, and suitability of the correct model Ergosol
product for the application.
The attached warranty form MUST be filled out
and posted to Amtech Medical within 30 days of
the invoice date.
0800 268 324
www.amtech.co.nz