INSTRUCTIONS
Retrofit Installation Instructions
•Warning - Risk of fire or electric shock. LED Retrofit Kit Installation
requires knowledge of luminaires electrical systems. If not
qualified, do not attempt installation. Contact a qualified electriction.
•WARNING - Risk of fire or electric shock. Install these kits only in
the luminaires that have the construction features and dimensions shown in the photographs and/or drawings.
Easy Install in Under 60 Seconds
•LED Retrofit Luminaire is designed for installation in
standard 5”-6” recessed downlight housing.
•Recommended dimmer: Lutron and Leviton
•Compatibility of housing not on this list can be
determined by measurement of the housing as detailed
in the attached drawing (Figure 1)
•WARNING - Risk of fire or electric shock. Do not alter, relocate, or
remove wiring, lampholders, power supply or any other electrical
component.
•WARNING - To prevent wiring damage or abrasion, do not expose
wiring to edges of sheet metal or other sharp objects.
•Do not make or alter any open holes in an enclosure of wiring or
electrical components during kit installation.
5-6i n c h
•CAUTION: Shock and fire hazard, do not use when enclosure is
broken.
•Suitable for use in enclosed recessed luminaires.
•Min. lamp compartement dimensions: 5” (D) x 5.5” (H) x or 6” (D) x
5.5” (H) where D is minimum diameter and H is minimum height
of the listed recessed luminaire compartment, as applicable.
This recessed luminaire has a E26 Edison screw-base and
is UL listed for installation and shallow recessed housing
series.
•Suitable for damp locations.
Compatible for 5 inch Can:
HALO:
LED Can: H550ICAT, H550RICAT
1. Before starting installation, please read this leaflet and keep it for
future reference.
2. To avoid possible electrical shock, be sure that the power supply is
turned off at fuse box or circuit breaker before installing or servicing
fixture.
3. During installlation do not let the product surface rub against other
hard objects or drop on the floor, otherwise the product will be
damaged.
4. Risk of fire: supply conductors (power wires) connecting the fixture
must be rated a minimum of 90˚C. If uncertain consult with an electrician.
5. The luminaire must be securely mounted; the bare wires of the power
cord must be properly insulated to prevent electrical hazards.
6. For indoor use only. Suitable for damp locations. Avoid contact of water
and other liquids with the light and power supply to avoid leakage and
electric shock.
7. Before the installation of any recessed lighting luminaire, check your
local electrical code. This code sets the wiring standards for your locality
and should be carefully studied before starting.
8. Protect the light from dust and dirt when painting or during construction.
9. Clean with a soft damp cloth only, do not use any chemical cleaners.
10. The luminaire light can be dimmed a with standard triac dimmer.
11. Input: 120VAC 60Hz POWER: 11w/15w
CFLC an: H524ICAT, H524RICAT, H570ICAT, H570RICAT,
H571ICAT, H572ICAT, H572RICAT, H573ICATLD,
H573RICATLD, H51CAT, H5RICA, H5T, H5RT
ALL-PRO:
Incandescent Can: EI500RAT, ET500, ET500R.
Juno: TC20R, TC20S, TC20, IC20R, IC20N, IC20NW,IC20S,
IC20W, IC20, IC25R, IC25W, PL526RE, ICPL526REN,
ICPL518E
Compatible for 6 inch Can:
HALO:
LED Can: H7ICT, H7ICAT, H7ICATNB, H7RICAT, H7RICT,
H7UICAT, H7UICT, H750RICAT, H750ICAT, H27ICAT,
H27ICT, H27RICAT, H27ICT, H27RICAT, H51CAT, HRICAT,
H750TCP
ALL-PRO:
Incandescent Can: EI700, EI700AT, EI700ATNB, EI700NB.
EI700RAT, IE700U, EI700 UAT, EI2700, EI2700AT, EI500AT,
EI500RAT
Juno: IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R,
IC25, IC25W, IC25S
For additional product and ordering information, please refer to the latest
manufacturer specification.
PG 1
FUSELED.COM
800 752 1660
1740 EMERSON AVE
OXNARD, CA 93033
INSTRUCTIONS
Retrofit Installation Instructions
In s ta lla tio n i n to H o u s in g s :
FIG.1-1
FIG.1-2
1. Loosen torsion spring bracket with screw.
If install into 6” can housings: Remove 2 torsion spring brackets
completely to keep them in the outward position. (FIG. 1-1)
If install into 5” can housing: Slide bracket to inward position. (FIG. 1-2)
Then, tighten screw.
2. Unscrew the wing nut inside the can to detach the socket bracket
from the can. Disengage the socket from the socket bracket. (FIG. 2)
3. Thread the socket adapter into the socket. (FIG. 3)
4. Plug the female connector of the retrofit trim into the male
connector of the socket adapter assembly. (FIG. 4).
5. Squeeze both torsion spring arms together and insert into the
torsion spring slots (or retainer brackets) of the can. Tuck all wires into
the can and carefully push the retrofit trim into can (note: to provide
enough room in shallow cans, carefully position socket adapter and
socket adjacent to the long side of the LED driver prior to inserting the
retrofit trim into the can. (FIG. 5)
R e pla c ing L ED Lu m in a ir e s :
1. With fingertips, pull down firmly on trim ring until module stops.
2. Squeeze torsion springs together to remove LED module.
FIG.2
FIG.3
3. Disconnect LED module wiring from recessed can (LED Connector
or screw in Edison base.)
D im m in g :
The LED luminaire can be dimmed with amany standard incandescent
dimmers, however, an electronic low voltage version of a standard
dimmer (with neutral connection is recommended for many
applications. Updates in dimmer technology and special conditions
may apply depending on the dimmer type being used. To be assured
of the latest information regarding luminaire and dimmer compatibility, please contact dimmer manufacturer.
E le c tr ic a l Co n n e c tio n :
N
AC120
L
Dimmer
FIG.4
FIG.5
Downlight
Downlight
Downlight
GND
P a c k in g L is t:
1. LED luminaire (with LED driver)
2. #18 Black/White connecting wire with E26 lamp holder (for L/N
input)
W a r r a n ty :
We offer a 5 year limited warranty. As with any electrical installation, a
qualified electrician must ensure compatibility of use with a particular
housing; this includes all applicable national and local electrical and
building codes. Installer is responsible for securely retaining the LED
module in a housing at time of installation.
PG 2
FUSELED.COM
800 752 1660
1740 EMERSON AVE
OXNARD, CA 93033