Heki 2 - Leisure Spares

advertisement
Heki 2
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
1
Heki 2.doc
12.08.2008
Glass dome
Cover lid
Glass dome
Hinge
Gas spring mounting
Tube bar
Gas spring
PROBLEM:
Replacing
Replacing
Replacing
Replacing
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
the
the
the
the
2
glass dome
tube bar
gas spring
gas spring mounting
Heki 2.doc
12.08.2008
Replacing the glass dome
Open the glass dome all the way. Remove the gas spring as described
under Replacing the gas spring. Thereafter, the hinge pins must be
removed with a long-nose pliers. Place the glass dome carefully down on a
padded surface and remove the gas spring mounting blocks. The new glass
dome is installed in the reverse order of sequence.
Replacing the tube bar
Remove the axis clamping caps on the gas spring mounting. Push the
colored cylinder pin from the inside outward with a punch. The tube bar
is installed in the reverse order of sequence.
Replacing the gas spring
Remove the axis clamping caps on the gas spring mounting. Push the
colored cylinder pin from the inside outward with a punch.
Attention!: The piston rod has right hand threading that engages with the
joint lug. The gas spring (piston rod) can be removed by turning it.
Installation takes place in the reverse order of sequence.
Replacing the gas spring mounting
Remove the gas spring and described under
Replacing the gas spring and Replacing the tube
bar. Loosen the Philips screws to remove the gas
spring block and remove the silicon seam from the
side. Install the new part in the reverse order of
sequence.
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
3
Heki 2.doc
12.08.2008
Outside frame
Brushes (up to 10/98)
Brush section (up to 10/98)
Sash
fastener with
screw
Outside frame
Mounting
PROBLEM:
Replacing the outside frame
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
4
Heki 2.doc
12.08.2008
Replacing the outside frame
Remove the inside frame as described under Replacing the inside frame.
Remove the inside frame and loosen the Phillips screws on the
mountings.
Attention!:
frame is removed.
The risk of rupturing the roof sheeting exists when the main
Begin by trying to lift the complete outer frame on one of the corners upward. Remove any
sealing residue from the surface of the roof and clean with a grease free agent. Apply a
suitable sealing agent (e.g. butyl) onto the sealing surface of the outer frame before installing
the main frame. Install the outside frame in the reverse order of sequence.
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
5
Heki 2.doc
12.08.2008
Interior frame
Fliegenschutzrollo
Innenrahmen
Federmotor
Verdunklungsrollo
Klemmfeder
Lüftungsgitter
P R O B L E M:
Replacing
Replacing
Replacing
Replacing
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
the
the
the
the
6
inner frame
spring motor
roller blind
insect guard roller
Heki 2.doc
12.08.2008
R e p l a c e m e nt o f t h e i n n e r f r a m e
Dismantle the ventilating grille (do not bend it back too strongly).
Loosen the screws which are located underneath it. The inner frame must
be detached by two persons and the cable connections loosened between
the inner and outer frames. The assembly is done in reverse order.
R e p l a c e m e n t o f t h e s p ri n g m o t o r
Dismantle the roller blind as described in ‘Replacement of the blackout
roller blind’ and ‘Replacement of the gauze shade’. Pull back the spring
motor from the roller blind’s shaft. Mount the spring motor in reverse
order after it has been checked or replaced, subject to considering the
tensioning rule.
Tensioning rule:
Tube length in mm/100 +3= revolutions of the spring motor
Example:
Tube length=1000mm 1000mm/100+3= 13 è 13 clockwise revolutions
R e p l a c e m e n t o f t h e b l a c k ou t r o l l e r b li n d
Take off the inner frame in the same way as described in ‘Replacement of
the inner frame’. Release the spring motor from the holding bracket with
the aid of pointed pliers.
Caution!
There is a risk of injury because the spring is under
tension!
The roller blind can be removed afterwards by tilting the closing rod out
of the inner frame. Care must be taken not to damage the surface coating
on the roller blind’s fabric when the closing rod is being tilted. The
installation is done in reverse order, subject to considering the tensioning
rule.
Tensioning rule:
Tube length in mm/100 +3= revolutions of the spring motor
Example:
Tube length=1000mm 1000mm/100+3= 13 è 13 clockwise revolutions
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
7
Heki 2.doc
12.08.2008
Replacement of the gauze screen
The gauze screen is replaced in the same way as described in ‘Replacement
system’.
Dometic Seitz GmbH
Altkrautheimer Straße 28 • Tel: 06294/907-0
D-74238 Krautheim / Jagst
8
of the blackout
Heki 2.doc
12.08.2008
Download