D I S T R I B U T I O N
Adams Rite Electric Strikes
7140 Electric Strike ANSI/BHMA EO 9321 (Grade 1)
UL
Features
•
•
•
•
•
•
Strike opening 5/8” X 1-7/16” X ½” deep, Bolt retainer is stainless steel
For use with Key in Lever latches
Faceplate is 1-1/4’ X 4-7/8”
Fail Safe/Fail Secure: Field Convertible from one mode to the other. However AC
intermittent solenoid must not be used continuously
Case: 1” X 3-3/8” X 1-5/8” deep, zinc
aluminum alloy
Voltage
Finish
Strike lip standard for 1-3/4” thick door,. Part number
7140
24 VAC
628, 313
Special order extended lips available
Stocked product
7100 Electric Strike ANSI/BHMA EO 9321 (Grade 1)
Features
•
•
•
•
•
•
Strike Opening: 5/8” X 1-7/16” X 1/2” Bolt
retainer is stainless steel
For use with Exit Device Pullman latches
Faceplate is 1-3/4” X 4-7/8”
Case 1” X 3-3/8” X 1-5/8”
Fail Safe/Fail Secure: Field selectable
Strike lip of proper length for 1-3/4” thick
door that closes flush with jamb edge
1
Stocked product
Part number
7100
Voltage
24 VAC
Finish
628, 313
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Electric Strikes
74R1 Ultra Line ANSI/BHMA EO 9321 (Grade 1)
Opens
electrically
under 35 lbs.
of preload
ELECTRIC STRIKES
AC-16
Options & Accessories
For Adams Rite Strikes
Features
•
•
•
•
•
•
Strike Opening: 5/8” X 1-7/16” X 9/16” Bolt
retainer is stainless steel
For use with Exit Device Pullman latches
Faceplate is 1-3/4” X 9 ¾”
Case 1: X 3-3/8” X 1-1/16”
Fail Safe/Fail Secure: Field selectable
Lip
Extension
Strike lip strike
Stocked product
Part number
Monitor
74R1
Switches
Voltage
24 VAC
Finish
628, 313
29-0218
Piezo Horn
Accessories
4603
Rectifier
PS-1
Power Supply
A
12V 30V
OR
A
24V 40V
12V 30VA
OR
24V 40VA
4606
Transformer
4605
Transformer
Electric Strikes Accessories
260Installs
Santa Fe Street
• 4603 rectifier Converts low voltage AC current to DC of same voltage.
in low voltage line
Pomona, California 91767
(800) 872-3267 Fax:(800) 232-7329
between transformer and strike. Full wave bridge tupelo Rated 2 amps. (www.adamsrite.com
200 PIV)
• 4605 transformer Converts 120 VAC to 12VAC/24VAC. Rated 40 Volt-amp output assures plenty of
power for strike release.
• 4606 transformer Converts 120 VAC current to 24VAC. Plugs into standard wall unit
2
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Exit Devices
8600 series Narrow stile Concealed Vertical Rod Device
Features
•
•
•
•
•
•
Non Handed
Door Height: Standard unit is adjustable for doors up to
66” above the selected bar height. Doors over 66” require
8655 Tall Door Kit. ( special order)
Door thickness: Fits 1-3/4 to 2-1/4” thick doors
Stile Width: Minimum 2”
Bar Height: Adjustable from 30” to 44”
Fasteners; Standard self tapping screws
Certifications/Warranty
•
•
•
•
5 Year limited warranty
UL Life Safety List
ANSI/BHMA A156.3 Grade 1
California State Fire Marshall approval
Stocked product
Part number
8611
8611
8622
Door width
36”
48”
36”
Finish
628
628
313
8800 series Rim Exit Device for Aluminum Door
Features
•
•
•
•
•
•
Stocked product
Certifications/Warranty
•
•
•
•
Non Handed
Door Height: Standard unit is adjustable for
doors up to 66” above the selected bar height.
Doors over 66” require 8655 Tall Door Kit.
(special order)
Door thickness: Fits 1-3/4 to 2-1/4” thick doors
Stile Width: Minimum 2”
Bar Height: Adjustable from 30” to 44”
Fasteners; Standard self tapping screws
5 Year limited warranty
UL Life Safety List
ANSI/BHMA A156.3 Grade 1
California State Fire Marshall
Part number
8801
8801
8802
3
Door width
36”
48”
36”
Finish
628
628
313
www.capitoldoors.com
Monitor Kits for upgrading any 3000 or 8000 Series device:
91-0897-01 - Single Switch
91-0897-02 - Dual Swit
D I S T R I B U T I O N
ELECTRIC
LATCH RETRACTION
Adams Rite
Exit Devices
Accessories/Options
The LR option use
solenoid mounted
pushbar for instantaneo
unlocking and locking of the e
Stocked
product
device
from
a remote location or acc
Part numberBecause
Door width electrical
Finish operation
control device.
8611 LR
36”, 48”
628
device is fail-secure,
this
option
can
be used on f
8622 LR
36”, 48”
313
rated as well as life-safety
applications.
In the event o
8801 EL
36”, 48”
628
8802 EL
36”
, 48”
313
power failure device automatically
relatches.
Requires the u
of PS-LR Power Supply, which will power two exit devic
Electric
Latch
Retraction
for
8600/8800
series Supply will void warranty).
(Using
an
alternate
to
the
PS-LR
Power
• The “LR” option for 8600 uses a solenoid mounted in the push bar for instantaneous unlocking
and locking of the exit device from a remote location. Fail secure operation. In the event of power
•
•
Specify
by adding "LR" after exit device model number. Ord
failure device re-latches
PS-LR
Power
Supply
Requires use
of PS LR Power
supply separately. Order Battery Backup Kit
separately
(BBK-LR).
Solenoid Specification:
16 Amps inrush/.5 Amps Hold
Solenoid Specifications:
16
Amps Inrush/.5
Hold in the push bar for instantaneous unlocking
The “EL” option
for 8800 uses aAmps
solenoid mounted
and locking of the
exitrated
device from
secure operation.
In the event of power
Solenoids
are
fora remote
bothlocation. Fail
intermittent
and continuous
operation.
failure device re-latches
Also see 4612 Power Transfer.
Electric Latch Retraction For 8800 Rim Device
•
•
•
Rim Devices Available 24DC ( stock) or 12VD (special order)
Solenoid Specification: 24VDC 6 Amps Inrush/Hold
MONITORED DUMMY PUSHBAR
8099M1 - Single Switch
8099M2 - Dual Switch
8099-00 - Dummy Only
4
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Exit Devices
Accessories/Options
Monitored Dummy Push Bar 8099M1
•
Dummy push bar with no latch mechanism but with
single switch ( dual switch available special order) Most commonly used with a maglock where bar is
used to turn off magnet and allow exit
Monitor/Signal Switch
Stocked product
Part number
8099M1
8099M1
Type door
Aluminum door
Aluminum
Electrical Options
for Exit Devices
Function
The entire line of Adams Rite Exit Devices can be ordered
Finishwith electrification options for stand-alone access control
628 or integration with maglocks, card readers, keypads, fire
628 alarms and other control systems. Different exit device
types have different installation and power requirements.
Door width
36”
48”
D-PS-1 Power Supply
PS LR Power Supply
Is required for the EL Retraction on the 8600 Vertical Rod exit device.
Featurs
•
115VAC or 230 VAC input power 0.7A/0.4A
•
Has two serviceable fuses:
Electric
Dogging
F1 transformer
out
put 6.3A/250V 5X20MM
F2 transformer output 3.15Z/250V 5X20MM
•
Hold Open times: Two timers from 2-60 seconds
•
Enclosure: Steel Cabinet measure 10” X 10-3/8” X 4-1/8” Blue baked enamel finish
8680 Escutcheon
UL
®
290481MP
Required to mount any
standard Mortise cylinder
with MS cam, mortise
*supplied less cylinder
Alarmed Exit Device
Electric
Latch
Retraction (LR Option)
Dogging
Key
for 8600/8800
Stocked product
Finish 628 aluminum
Electric
Dogging
5
www.capitoldoors.com
Alarmed
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
MS1850S Deadbolt
MS Deadbolt 1”x6 7/8” Faceplate
MS 1850S ANSI/BHMA Type E8211 (Grade 2)
Cylinder cam
Cylinder Cam: MS1850S
series locks are operable
by any standard 1-5/32”
diameter cylinder with MS
cam as shown
Feature
•
A huge bolt of laminated stainless steel, nearly three inches long, activated by a pivot mechanism.
•
Bolt: 5/8” x 1-3/8” X 7-/8” with 1-3/8” throw. Eight ply laminated stainless steel.
•
Case: Steel with corrosion resistant plating. 1” X 6”
•
Cylinder Backset: 31/32”,1-1/8” , 1-1/2” available special order
•
Cylinders: Not supplied, must have MS dimension cam
Options (special order)
•
Flat, Radius w/Weather Strip, Beveled faceplates
Stocked product
Part number Backset
MS1851S210 31/32”
MS1851S310 1-1/8”
6
Faceplate
Radius
Radius
Finish
628, 313
628, 313
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
MS1850S-050 Deadbolt
MS Deadbolt for aluminum style door1”x 6-7/8” Faceplate
MS 1850S-050 ANSI/BHMA Type E8281 (Grade 1)
Cylinder cam
Cylinder Cam: MS1850S
series locks are operable
by any standard 1-5/32”
diameter cylinder with
MS cam as shown
Feature
•
The MS Hookbolt deadlock is designed for sliding glass doors. The bolt is hook shaped to resist
intrusion for sliding doors .
•
Bolt: 5/8” X 1-3/8” with 13/16” throw. Eight ply laminated stainless steel
•
Case: Steel with corrosion resistant plating 1” X 6”
•
Cylinder Backset: 31/32” , 1-1/8” and 1-1/2”
•
Cylinders: Not supplied, must have MS dimension cam
Options (special order)
•
Flat, Radius w/Weather Strip, Beveled faceplates
•
1-1/2” Backset
Stocked product
Part number Backset
MS1851S250 31/32”
MS1851S350 1-1/8”
7
Faceplate
Radius
Radius
Finish
628, 313
628, 313
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
Exit Indicators 4089
Features:
•
Provides notification of an exit doors locked or open
condition. Includes two permanent adhesive head signs:
THIS DOOR TO REMAIN UNLOCKED DURING BUSINESS
HOURS and THIS DOOR TO REMAINED UNLOCKED WHEN THE
BUILDING IS OCCUPIED
•
Message panel OPEN appears in black letters on white
background when lock is retracted and LOCKED in red letters
when actuated
Compatible Locks
•
MS1830,MS1837,MS1850S,MS1850S-050,MS1860,MS1870,
MS1890
Options
•
313 special order
Stocked product
Part number
4089
Finish
628
MS 4043 Cylinder Guard
For aluminum/Hollow Steel Door
Features
•
Security Ring: Made of hardened steel. Free swiveling
•
Retainer Ring of hardened steel, permits security ring
to swivel
Options
•
313 special order
Stocked product
Part number
MS4043
8
Finish
628
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
4510 series Standard Duty Deadlatch for
Aluminum Style Doors
ANSI/BHMA Type E823 (Grade 2)
Cylinder cam
Cylinder Cam:
MS1850S series locks
are operable by any
standard 1-5/32”
diameter cylinder with
MS cam as shown
Features
•
Reverse turn of the key while bolts is held retracted retains the bolt, to allow two way traffic for public
buildings which require free entrance at certain times
•
Case: Steel, 1” X 5 13/16”
•
Latch Bolt 1/2” X 1” X 1/2” Throw. All metal with hardened steel internal pins
•
Auxiliary Bolt All metal
•
Cylinder Backset: 31/32” and 1-1/8” . 7/8” and 1-1/2” special order only
Options (special order)
•
Faceplates: Flat, Radius w/Weather Strip, , Beveled •
Backset: 7/8”, 1-1/2”
•
Strikes: 4901 (4,63”)
Stocked product
Part number
4511-26
4511-36
9
Backset
31/32”
1-1/8”
Faceplate
Radius
Radius
Finish
628, 313
628, 313
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
4560 Deadlach Handles
Features
•
Zinc alloy lever with ADA compliant design
•
Designed to operate 4500/4700/4900/ series latches
•
Escutcheon: 1-3/8” X 4” for narrow style doors
•
Handed but field reversible
•
Cam plugs included
Options (special order)
•
121 Dark Bronze
Stocked product
Part number
4560
10
Finish
130 (aluminum)
Hand
RH (Field Reversible)
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
4569 Eurostyle Deadlatch Handles
Features
•
Zinc alloy lever with ADA compliant design
•
Cam plugs included
•
Designed to operate 4500/4700/4900/ series latches
•
Escutcheon: 1-3/8” X 4” for narrow style doors
•
Handed but field reversible
Options (special order)
•
121 Dark Bronze
Stocked product
Part number
4569
11
Finish
130 (aluminum)
Hand
RH (Field Reversible)
www.capitoldoors.com
D I S T R I B U T I O N
Adams Rite Swinging and Sliding Door Hardware
4590 Deadlatch Paddle
Features
•
Paddle is made of extruded aluminum
•
Operation: Push and pull feature for use on any Adams Rite 4500/4700/4000/ MS1890 locks set.
Four modes
•
Push to left, push to right, pull to left and pull to right
•
Cam plug furnished
•
Escutcheon: Zinc alloy
Stocked product
Part number
459001
459002
459003
459004
12
Operation
Pull to Left
Push to Left
Pull to Right
Push to Right
Finish
Aluminum
Aluminum
Aluminum
Aluminum
www.capitoldoors.com