UB-1TF Universal
Touch Free Button
NoTouch®
Technology
We protect the things that protect you.®
NOTES
It is important to read, understand and follow all instructions provided with
this product. It is the installer’s responsibility to comply with NFPA 70 &
101, NEC, mounting specifications according to ADA and other applicable
electrical codes. To avoid electrical shock, DO NOT attempt to install
this product when power is on. ADA mounting compliance requires the
operable part of the initiating device shall not be less than 3 1/2 ft. (1.1m ) or
greater than 4 1/2 ft. (1.37m) above finished floor surface. After installation
and testing are complete, provide a copy of this manual to all personnel
responsible for testing and maintenance of this product.
4.80 in.
(122mm)
6.25 in.(159mm)
3.22 in.(82mm)
.75 in.
(19mm)
.77 in.
(20mm)
POWER
Switch:
Input: 12 VDC ± 15%
Standby Power: 15 mA
Active: 25 mA
Operating temperature:
-4° to 158°F (-20° to 70°C)
Message LED:
12-24 VDC
Form “C” contact rating:
30 VDC, 1A
-2-
T LATCH TIME ADJUSTMENT:
ISE - LONG
RCLOCKWISE - SHORT
~0.5 ~ 60 sec.
ETAIL A
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE -MESSAGE
CLOSE
1. TO CHANGE BUTTON COLOR AND ROUND
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
DIFFUSER
~1 ~ 10 CM
MESSAGE LENS
POWER IN
12-30 VDC/VAC
œ
SWITCH NUT
+
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE - CLOSE
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
ALIGN TABS
~1 ~ 10 CM
TO NOTCHES
ON BUTTON
LENS
DETAIL A
BUTTON LENS
1. Choose button color. If same as existing, proceed to 2.
2. a. Loosen nut on back of switch, and push switch through plate far enough to grasp button from back edge and remove button lens.
b. Push switch back into plate and tighten nut. Be careful not to over-
tighten.
3. Select color lens. Align notches on button with tabs on switch and push until it
snaps together.
UB-1L LED PCB
NYLON WASHER
SELF TAPPING SCREW
2. CHANGE TOP MESSAGE
(Refer to notes on pg. 2 for “EMERGENCY”
message use.
1. Remove LED circuit board.
2. Remove current message by pushing in and
down on tabs 1 and 2 with a small screwdriver.
If necessary, also push in and down on tabs 3
UB-1L message
LED PCB
and 4. Once
is loose, remove from the
NYLON WASHER
front
of theSCREW
plate.
SELF
TAPPING
3. Select new message and snap into place.
Blank plates are included to create your own
19085 #6 - 32 x 1 in. OVAL
custom message.
1
SCREWDRIVER
2
P
12 OW
-30 ER
VD IN
C/
VA
œ
C
+
HEAD MACHINE SCREW
(2) PROVIDED
-3-
3
A
4
Power In
12œ30 VDC/VAC
Safety Tech. Int·l Inc.
P/N UB-11. Ver 1.0
wwyy
4.80 in.
(122mm)
3. ATTACH WIRE PLUG
6.25 in.(159mm
Wire Color Code with power applied:
3.22 in.(82mm)
Red: +12 VDC
Black: -12 VDC
Green: N.C.
Blue: COM
White: N.O.
.75 in.
(19mm)
.77 in.
(20mm)
P
12 OW
-30 ER
VD IN
C/
VA
œ
C
+
COLOR CODE:
+12 VDC
RED
BLACK -12 VDC
A
GREEN N.O.
BLUE COM
WHITE N.C.
INSERT PLUG INTO SWITCH WITH
RIBS IN THIS DIRECTION
CONTACT LATCH TIME ADJUSTMENT:
CLOCKWISE - LONG
COUNTERCLOCKWISE - SHORT
RANGE: ~0.5 ~ 60 sec.
ACTIVATION RANGE ADJUSTMENT:
CLOCKWISE - CLOSE
COUNTERCLOCKWISE - FAR
RANGE: ~0.4 ~ 4 INCHES
~1 ~ 10 CM
DETAIL A
-4-
4. ATTACH POWER FOR MESSAGE LED (if desired)
WIRING DIAGRAMS (Color codes are shown with power applied and button LED red during
wiring)
A. Normally Open Exit Device
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED red
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED green
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
UB-1TF LED
UB-1TF LED
B. Normally Closed Exit Device
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED red
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED green
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
UB-1TF LED
UB-1TF LED
UB-1TF Wire Color Code
CONNECTOR
WIRE COLOR
POWER OFF
(SUPERVISORY)
POWER ON
UNTRIGGERED
POWER ON
TRIGGERED
RED
BLACK
GREEN
BLUE
WHITE
+12V
-12V
N.O.
COM
N.C.
+12V+12V
-12V
-12V
N.C.
N.O.
COM
COM
N.O.
N.C.
None
Red
LED color
-5-
Green
5. MOUNT BUTTON ONTO ELECTRICAL BOX
UB-1
NYLON W
SELF TAPPING S
19085 #6 - 32 x 1 in. OVAL
HEAD MACHINE SCREW
(2) PROVIDED
6. CUSTOM LABELS
To create your own custom label, size to fit in .48h x 2.23w as shown below.
Also available online at: www.sti-usa.com/ublabel
.48 in.
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED red
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
2.23 in.
UB-1TF LED
-6-
GREEN
BLUE
WHITE
BLACK
RED
Message lit with button LED gre
N.C.
EXIT
COM
DEVICE
N.O.
INPUT
GND
+12VDC
UB-1TF LED
ACCESSORIES
DESCRIPTION
PART #
SUB-71100A-COLOR
(red, blue, green, white or yellow)
COLOR MATCH BACKBOX KIT
CUSTOM LABEL APPLIED TO BLANK
MESSAGE PLATES
UB-1CL-COLOR
(blue, green, white or yellow)
24 VOLT LED
WHITE (STANDARD)
RED
BLUE
GREEN
10147
10145
10141
10143
12 VOLT LED
RED
BLUE
GREEN
10144
10140
10142
COVERS
BOPPER STOPPER
UNIVERSAL STOPPER
STOPPER II
STI-6518
STI-13000 Series
STI-1100 Series
See website for complete cover details
-7-
WARRANTY
Three year guarantee against breakage of polycarbonate in normal use (one year on
electro mechanical and electronic components).
Electronic warranty form at www.sti-usa.com/wc14.
2306 Airport Rd • Waterford, MI 48327
Phone: 248-673-9898 • Fax: 248-673-1246
info@sti-usa.com • www.sti-usa.com
Safety Technology International (Europe) Ltd.
Unit 49G Pipers Road • Park Farm Industrial Estate • Redditch
Worcestershire • B98 0HU • England
Tel: 44 (0) 1527 520 999 • Fax: 44 (0) 1527 501 999
E-mail: info@sti-europe.com • Web: www.sti-europe.com
Printed in USA
Inst. Sht. UB-1TF Button MARCH2010