10-Port Antenna
Frequency Range
Dual Polarization
HPBW
Adjust. Electr. DT
R1
B1
Y1
B2
Y2
698–960 1695–2180 2490–2690 1695–2180 2490–2690
X
X
X
X
X
65°
65°
65°
65°
65°
2°–16°
2.5°–12°
2.5°–12°
2.5°–12°
2.5°–12°
set by
10-Port Antenna 698–960/1695–2180/2490–2690/1695–2180/2490–2690 65°/65°/65°/65°/65°
15/17/17/17.5/18dBi 2°–16°/2.5°–12°/2.5°–12°/2.5°–12°/2.5°–12°T
Type No.
80010874
Left side, lowband
R1, connector 1– 2
698 – 960
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
Upper Side Lobe
Suppression, 20° Sector
above Main Beam
Cross Polar Isolation
Port to Port Isolation
MHz
dBi
dBi
698 – 806
14.2
14.1 ± 0.5
791 – 862
14.6
14.5 ± 0.6
824 – 894
14.8
14.7 ± 0.6
880 – 960
15.0
14.8 ± 0.4
°
67 ± 3.5
63 ± 3.8
62 ± 2.6
61 ± 1.7
dB
> 22
> 23
> 24
> 27
dB
> 22
> 23
> 23
> 21
dB
> 7.5
> 7.0
> 7.0
> 7.0
dB
< 1.5
< 1.5
< 1.5
< 2.5
°
14.1 ± 1.2
12.9 ± 0.6
12.5 ± 0.7
11.7 ± 0.6
°
2.0 – 16.0
°
< 0.6
< 0.6
< 0.6
< 0.5
dB
> 12
> 14
> 13
> 14
dB
> 14
> 14
> 13
> 14
dB
dB
> 28
> 28 (R1 // B2, Y2)
> 30 (R1 // B1, Y1)
936.5152 ngmn 04.25.02.02 Subject to alteration.
Max. Effective Power
W
300 (at 50 °C ambient temperature)
per Port
Max. Effective Power
W
600 (at 50 °C ambient temperature)
Port 1–2
Values based on NGMN-P-BASTA (version 9.6) requirements.
80010874 Page 1 of 4
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
10-Port Antenna
Left side, highbands
Cross Polar Isolation
Port to Port Isolation
MHz
dBi
dBi
1695 – 1880
16.4
16.3 ± 0.6
1695 – 2180
1850 – 1990
16.9
16.8 ± 0.4
2490 – 2690
2490 – 2690
17.0
16.7 ± 0.5
°
63 ± 5.9
59 ± 2.5
57 ± 3.6
61 ± 6.0
> 24
> 26
> 27
> 26
dB
> 16
> 20
> 22
> 15
dB
> 8.0
> 8.5
> 10.0
> 9.0
dB
< 3.0
< 2.5
< 1.5
< 2.0
°
6.8 ± 0.3
6.5 ± 0.3
6.2 ± 0.5
4.9 ± 0.3
°
2.5 – 12.0
2.5 – 12.0
°
< 0.3
< 0.3
< 0.3
< 0.3
dB
> 16
> 16
> 16
> 17
dB
> 13
> 16
> 16
> 15
dB
> 28
> 30 (B1 // R1, Y1, B2, Y2)
> 30 (Y1 // R1, B1, B2, Y2)
dB
Right side, highbands
Cross Polar Isolation
Port to Port Isolation
1920 – 2180
17.1
17.0 ± 0.5
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 3–4 + Port 7–8
Values based on NGMN-P-BASTA (version 9.6) requirements.
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
Upper Side Lobe
Suppression, 20° Sector
above Main Beam
Y1, connector 7–8
7– 8
150 (at 50 °C ambient temperature)
400 (at 50 °C ambient temperature)
B2, connector 5 – 6
Y2, connector 9–10
9– 10
MHz
dBi
dBi
1695 – 1880
16.9
16.9 ± 0.3
1695 – 2180
1850 – 1990
17.2
17.1 ± 0.3
°
66 ± 2.9
66 ± 2.3
66 ± 2.7
62 ± 2.5
dB
> 25
> 24
> 23
> 25
dB
> 20
> 20
> 21
> 15
dB
> 14.0
> 12.5
> 12.0
> 7.0
dB
< 1.0
< 2.0
< 2.0
< 1.0
°
6.9 ± 0.4
6.5 ± 0.4
6.2 ± 0.6
°
1920 – 2180
17.4
17.3 ± 0.5
2490 – 2690
2490 – 2690
18.0
17.9 ± 0.3
2.5 – 12.0
5.0 ± 0.3
2.5 – 12.0
°
< 0.3
< 0.3
< 0.4
< 0.4
dB
> 17
> 16
> 17
> 16
dB
> 16
> 15
> 15
> 15
dB
dB
Max. Effective Power
W
per Port
Max. Effective Power
W
Port 5–6 + Port 9–10
Values based on NGMN-P-BASTA (version 9.6) requirements.
> 28
> 30 (B2 // R1, B1, Y1, Y2)
> 30 (Y2 // R1, B1, B2, Y2)
150 (at 50 °C ambient temperature)
400 (at 50 °C ambient temperature)
Page 2 of 4 80010874
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
936.5152 ngmn 04.25.02.02 Subject to alteration.
Frequency Range
Gain at mid Tilt
Gain over all Tilts
Horizontal Pattern:
Azimuth Beamwidth
Front-to-Back Ratio,
Total Power, ± 30°
Cross Polar Discrimination
at Boresight
Cross Polar Discrimination
over Sector
Azimuth Beam
Port-to-Port Tracking
Vertical Pattern:
Elevation Beamwidth
Electrical Downtilt
continuously adjustable
Tilt Accuracy
First Upper Side Lobe
Suppression
Upper Side Lobe
Suppression, 20° Sector
above Main Beam
B1, connector 3 ––4
4
10-Port Antenna
Mechanical specifications
Electrical specifications, all systems
Impedance
Ω
50
VSWR
< 1.5
Return Loss
dB
> 14
Interband Isolation
dB
> 28
Passive Intermodulation dBc < –150 (2 x 43 dBm carrier)
Polarization
°
+45, –45
900 (at 50 °C ambient
Max. Effective Power
W
temperature)
for the Antenna
Values based on NGMN-P-BASTA (version 9.6) requirements.
Input
Connector Position
Adjustment Mechanism
Wind load
(at Rated Wind
Speed: 150 km/h)
Max. Wind Velocity
N | lbf
km/h
mph
Height / Width / Depth mm
inches
Category of
Mounting Hardware
Weight
kg
lb
Packing Size
mm
inches
Scope of Supply
10 x 4.3-10 female
bottom
FlexRET,
continuously adjustable
Frontal
690 | 155
Lateral
250 | 56
Rearside
1270 | 286
241
150
1499 / 378 / 164
59.0 / 14.9 / 6.5
XH (X-Heavy)
31.0 / 36.0 (clamps incl.)
68.3 / 79.3 (clamps incl.)
1681 / 402 / 248
66.2 / 15.8 / 9.8
Panel, FlexRET and
2 units of clamps
for 55 – 115 mm |
2.2 – 4.5 inches diameter
Accessories (order separately if required)
2 clamps
1 downtilt kit
Site Sharing Adapter
Site Sharing Adapter
Gender Adapter
Port Extender
Weight
Units per
approx. kg | lb antenna
Mast diameter: 110 – 220 | 4.3 – 8.7
Downtilt angle: 0° – 12°
3-way (see figure below)
6-way (see figure below)
9.4 | 20.7
10.6 | 23.4
0.7 | 1.5
1.4 | 3.1
Solely to be used in combination with 0.045 | 0.099
the FlexRET module 86010153V01
0.16 | 0.35
1
1
1
1
Accessories (included in the scope of supply)
85010096
86010153V01
2 clamps
FlexRET
Mast diameter: 55 – 115 | 2.2 – 4.5
5.0 | 11.0
1
1
1499 | 59.0
85010097
85010099
86010154
86010155
86010162
86010163
Remarks
mm | inches
1318 | 51.9
Description
1556 | 19.2
Type No.
Material:
Reflector screen: Aluminum.
Fiberglass housing: It covers totally the internal antenna components. The special
design reduces the sealing areas to a minimum and guarantees the best weather
protection. Fiberglass material guarantees optimum performance with regards to stability,
stiffness, UV resistance and painting. The color of the radome is light grey.
All nuts and bolts: Stainless steel or hot-dip galvanized steel.
Grounding:
The metal parts of the antenna including the mounting kit and the inner conductors are
DC grounded.
Configuration example
with Site Sharing Adapter 86010154
FlexRET
FlexRET
FlexRET
Configuration example
with Site Sharing Adapter 86010155
FlexRET
Site Sharing Adapter
3-way
3)
FlexRET
1) 22 | 0.9
2) 150 | 5.9
3) ’11 | 0.4
Site Sharing Adapter
6-way
AISG
BTS1
FlexRET
All dimensions
in mm | inches
AISG
BTS2
1)
2)
936.5152 ngmn 04.25.02.02 Subject to alteration.
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
BTS3
BTS1
BTS2
BTS3
BTS4
BTS5
BTS6
For more information please refer to the respective data sheets.
80010874 Page 3 of 4
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
10-Port Antenna
B1
L
4
B1
L
1695-2180
1695-2180
Y1
Y1
L
8
7
2490-2690
R
R1
L
R1
2
L
698 - 960
1
B2
R
5
1695-2180
1695-2180
Y2
Y2
R
698 - 960
6
10
2490-2690
R
9
2490-2690
97 | 3.8
2490-2690
L
B2
3
141 | 5.5
164 | 6.5 *
229 | 9.0 *
Layout of interface:
131 | 5.2
221 | 8.7
311 | 12.2
378 | 14.9 *
Bottom view
* Dimensions refer to radome
All dimensions in mm | inches
Frequency range
Array
Connector
698– 960 MHz
1695–2180 MHz
1695–2180 MHz
2490–2690 MHz
2490–2690 MHz
R1
B1
B2
Y1
Y2
1–2
3–4
5–6
7–8
9 – 10
Page 4 of 4 80010874
Y1
Y2
B1
R1
Left
B2
2x
Right
Any previous data sheet issues have now become invalid.
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
936.5152 ngmn 04.25.02.02 Subject to alteration.
Correlation Table
FlexRET
A flexible, integrated solution for adjusting the electrical downtilt of Kathrein FlexRET antennas.
●
●
Compliant to AISG 1.1 and 3GPP/AISG 2.0
Single RETs or Multi RET displayed
Protocols
Logical interface ex factory 1)
Operates as
Ex factory
Input voltage range
V
Power consumption
W
Connectors
Hardware interfaces
Housing material
Weight
Packing size
(H x W x D)
Dimensions
(H x W x D)
●
Daisy Chain feasibility
Pre-configurated
86010153
Type No.
Adjustment time
(full range)
Adjustment cycles
Temperature range
Protection class
Lightning protection
●
sec
°C
g
lb
mm
inches
mm
inches
compliant to AISG 1.1 and 3GPP/AISG 2.0
3GPP/AISG 2.0
Single RETs or Multi RET
Single RETs
10 ... 30 (pin 1, pin 6)
< 0.5 (stand by); < 10 (motor activated)
2 x 8 pin connector according to IEC 60130-9; according to AISG
Daisy chain in: male; Daisy chain out: female
RS 485A/B (pin 5, pin 3);
power supply (pin 1, pin 6); DC return (pin 7);
according to AISG / 3GPP
40
(typically, depending on antenna type)
> 50,000
–40 … +60
IP 24 (installed)
AISG interface (each pin)
2.5 kA (10/350 μs)
8 kA (8/20 μs)
Profile: Aluminum anodized; cover: Aluminum die cast coated
350
0.77
245 x 93 x 102
9.6 x 3.6 x 4
142 x 71 x 50.4
5.6 x 2.8 x 2
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 to AISG 1.1 with a vendor
specific command. Start-up operation of the FlexRET is only possible in a RET system supporting
3GPP/AISG 2.0!
1)
Please note:
If the Primary which controls the FlexRET system does not support the default ex-factory interface
setting, then the RCU must be switched to the appropriate standard of the Primary before installation.
Please contact Kathrein for further information.
936.4643/b
Subject to alteration.
If the FlexRET of an antenna has to be replaced, the FlexRET gets the information stored in the antenna
after power on automatically. It is not necessary to configurate the FlexRET manually.
Standards:
EN 60950-1 (Safety)
EN 60950-22 (Safety – Equipment installed outdoor)
EN 55022 (Emission)
EN 55024 (Immunity)
ETS 300019-1-4 (Environmental)
UL 60950-1; 1st edition
Certification:
CE, FCC
Scope of supply:
FlexRET
Optional:
Site Sharing Adapter (86010154 or 86010155) to create independent logial
interfaces at one antenna or site. Makes it possible to operate with more
than one independent Node B.
Please note:
In general, the addressing of the FlexRET is automatically performed. Only in case the FlexRET is
manually addressed, the serial number has to be extended by the corresponding colour coding extension
(e.g. CSG351234-R1). The respective information can be found on the site documentation which is
included in the scope of supply.
86010153 Page 1 of 4
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
FlexRET
Startup of FlexRET
The FlexRET module included in the antenna is preconfigured with the following information:
Antenna model no., Antenna Serial no., Antenna configuration data. After connecting a control
cable and scanning the antenna line devices (ALD) the used primary (e.g. NodeB, ALC, etc.)
will find the FlexRET. You only need to insert your additional data.
Connecting the control cables:
Connect a control cable to the daisy chain input of the FlexRET. The tightening torque for fixing the
connector must be 0.5 – 1.0 Nm (‘hand-tightened’).
The connector should be tightened by hand or by a special torque screw driver (order no.
85010080).
See also data sheet for Kathrein AISG-cable (86010007, ...).
Please note: To ensure the tightness of the RET System, Kathrein recommend the use of
Kathrein components only.
Please note: If the daisy chain output is not used, do not remove the protection cap.
936.4643/b
Subject to alteration.
For daisy chain operation, remove the protection cap and attach a control cable to interconnect
with the daisy chain input of the subsequent FlexRET or external RCU.
Please note: Do not remove the protection cap on the daisy chain output of the last FlexRET
or RCU device.
Page 2 of 4 86010153
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
FCC – Statements
'!!! *,/%,1
(+$"%!(,)')AE$)'*!(4%')$#((* ))$)$!!$,#),$
$#)$#(39A:(+".#$)*('"*!#)''#2#9B:)(+"*()%)#.
#)''#'+2#!*##)''#))".*(*#('$%')$#4
*,/%,+/
$)3(&*%"#)(#)()#$*#)$$"%!.,))!")($'!(()!+2
%*'(*#))$%')AE$)*!(4(!")('(#)$%'$+'($#!%'$))$#
#()'"*!#)''##'(#)!#()!!)$#4(&*%"#)#')(2*((##
')'$'&*#.#'.#2#$)#()!!#*(#$'#,))#()'*)$#(2".
*('"*!#)''#)$'$$""*#)$#(4$,+'2)'(#$*'#)))
#)''#,!!#$)$*'#%')*!'#()!!)$#4)(&*%"#)$(*('"*!
#)''#)$'$$')!+($#'%)$#2,#)'"#.)*'##)&*%"#)$
#$#2)*('(#$*')$)'.)$$''))#)''#.$#$'"$'$)$!!$,#
"(*'(3
8$'#)$''!$))'+##)##4
8#'()(%')$#),#)&*%"#)#'+'4
8$##))&*%"#)#)$#$*)!)$#'*)'#)'$")))$,)'+'(
$##)4
8$#(*!))!'$'#-%'#'$6)##$'!%4
&!0%,%.
(+$"%!(,)#*()'.#!#7-"%)()#'9(:4%')$#((* ))$
)$!!$,#),$$#)$#(39A:)(+".#$)*(#)''#2#9B:)(+"*()
%)#.#)''#2#!*##)''#))".*(*#('$%')$#$)+4
Subject to alteration.
&++.
936.4643/b
%'(#)%%'!()$#$'"*-=#*()'#%%!!(*-%%'!('$
-"%)(!#4=-%!$))$#()*)$'(*-*-$#)$#((*+#)(39A:!=%%'!#
$)%(%'$*''$*!!2)9B:!=*)!()*'!=%%'!$)%)')$*)'$*!!
'$!)'&*(*2""(!'$*!!()(*(%)!=#$"%'$"))'!$#)$##"#)4
(!(()!%%')*($"%!(,)##7@@C4
)%%'!#*"'&*!!((()$#$'"!#$'"7@@C*#4
*,/%-,(!!!)
;#.<#($'"$)$#(#$)-%'((!.%%'$+.)%').'(%$#(!$'$"%!#$*!
+$)*('5(*)$').)$$%'))&*%"#)4
86010153 Page 3 of 4
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
FCC – Statements
Compliance Information Statement
(Declaration of Conformity Procedure)
Responsible Party: Kathrein Inc., Scala Division
Address: PO Box 4580, Medford Oregon . 97501
Telephone: (+01)541 779 6500
Type of Equipment:
936.4643/b
Subject to alteration.
Model Name: FlexRET
FCC ID SP3-86010153
Page 4 of 4 86010153
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820
Mounting Hardware
Clamp
(Wind Load Category “XH”)
Clamp
85010096
Type No.
Suitable for
mast diameter
Scope of supply
mm
inches
Material – Clamp
– Screws
– Nuts
Weight
55 – 115
2.2 – 4.5
1 x lower clamp
1 x upper clamp
Hot-dip galvanized steel
Hot-dip galvanized steel
Stainless steel
5.0
11.0
kg
lb
F
Torque
MA = 40 Nm
Torque
H
upper clamp
MA = 40 Nm
’D
Torque
MA = 40 Nm
A
H
B
C
lower clamp
upper clamp
Torque
MA = 40 Nm
G
lower clamp
G
E
1)
Attention!
936.5063
Subject to alteration.
Square of the screw must be
positioned in the square hole
before tightening the nut.
2)
All nuts have the same
wrench size 17.
mm
inches
A
B
C
D
E
F
G
H
200
7.9
69
2.7
89
3.5
55 – 115
2.2 – 4.5
150
5.9
130
5.1
(19)
(0.7)
(39)
(1.5)
Please note: Kathrein does not recommend to use counter nuts.
85010096 Page 1 of 1
www.kathrein.com
KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820