I
CONTRACT NO. GS 14826R
,-
SECTION 081416
FLUSH WOOD DOORS
[
PART 1 -GENERAL
1.1
I-
RELATED DOCUMENTS
A.
. 1.2
I
Drawings and general provisions . of the Contract, including General and Supplementary
Conditions and Division 01 Specification Sections, apply to this Section .
SUMMARY
A.
Sectio.n Includes:
1.
2.
3.
1.3
A
· B.
ACTION SUBMITTALS
Product Data: For each type of door. Include
openings.
1.4
det~;~Hs
of core and edge construction and trim for
Shop Drawings: Indicate location, size, and hand of each door; elevation of each kind of door;
construction details not covered in Product Data; and the following:
1.
2.
3.
4.
5.
. 6.
C.
Solid-core doors with wood-veneer faces.
Factory finishing flush wood doors.
Factory fitting flush wood doors to. frames and factory machining for. hardware.
Dimensions and locations of blocking.
Dimensions and locations of mortises and holes for hardware.
Dimensions and locations of cutouts.
Undercuts.
· Requirements for veneer matching .
Doors to. be factory finished and finish requirements.
Samples: For factory-finished doors.
INFORMATIONAL SUBMITTALS
I_
A
Sample Warranty: For special warranty.
B.
Quality Standard Compliance Certificates: AWl Quality Certification Program certificates.
1.5
A
QUALITY ASSURANCE
Manufacturer Qualifications: A qualified manufacturer that is a certified participant in AWl's
Quality Certification Program.
081416- 1
CONTRACT NO. GS 14826R
1.6
DELIVERY, STORAGE, AND HANDLING
A
Comply with requirements of referenced standard and manufacturer's written instructions.
B.
Package doors individually in plastic bags or cardboard cartons.
C.
Mark each door on bottom rail with opening number used on Shop Drawings.
1.7
FIELD CONDITIONS
A
1.8
Environmental Limitations: Do not deliver or install doors until spaces are enclosed and
weathertight, wet work in spaces is complete and dry, and HVAC system is operating and
maintaining ambient temperature and humidity conditions at occupancy levels during remainder
of construction period.
WARRANTY
A
A Special Warranty: Manufacturer agrees to repair or replace doors that fail in materials or
workmanship within specified warranty period.
1.
Failures include, but are not limited to, the following:
a.
cup, or twist) more than 1/4 inch in a 42-by-84-inch section.
of core construction in face veneers
0.01 inch ;n a
b,
span.
2.
Warranty Period for Solid-Core Interior Doors: Life of installation.
PART .2- PRODUCTS
2.1
MANUFACTURERS
A
Manufacturers: Subject to compliance with requirements, available manufacturers offering
products that may be incorporated into the Work include, but are not limited to the following:
1.
2.
3.
4.
5.
B.
2.2
Algoma Hardwoods, Inc.
Eggers Industries.
Graham Wood Doors; ASSA ABLOY Group.
Lambton Doors.
Mohawk Flush Doors, Inc.
Source Limitations: Obtain flush wood doors from single manufacturer.
FLUSH WOOD DOORS, GENERAL
A
Quality Standard: In addition to requirements specified, comply with AWl's, AWMAC's, and Wl's
"Architectural Woodwork Standards."
B.
WDMA I.S.1-A Performance Grade:
081416- 2
CONTRACT NO. GS 14826R
1.
2.
C.
Heavy Duty unless otherwise indicated.
Extra Heavy Duty: Public toilets and janitor's closets.
Structural-Composite-Lumber-Core Doors:
1.
Structural Composite Lumber: WDMA LS.1 0.
a.
b.
2.3
Screw Withdrawal, Face: 700 lbf.
Screw Withdrawal, Edge: 400 lbf.
VENEER-FACED DOORS FOR TRANSPARENT FINISH
A.
Interior Solid-Core Doors:
.,
1.
2.
3.
4.
5.
2.4
Grade: Custom (Grade A faces).
Species, Cut, and Matching: Match existing doors.
Exposed Vertical and Top Edges: Applied wood-veneer edges of same species as faces
·
and covering edges of faces -edge Type B.
Care: Either glued wood stave or structural composite lumber.
Construction: Five plies. Stiles and rails are bonded to core, then entire unit is abrasive
planed before veneering.
DOORS FOR OPAQUE FINISH
!nterior Solid ...(;ore
1.
2.
Grade: Custom.
Faces:
a.
3.
4.
5.
6.
Hardboard Faces: Ai\lSI A 1
or Class 2
Exposed Vertical and Top
Any closed-grain hardwood.
Core: Structural composite lumber.
Construction: Seven plies, either banded or nonbonded.
WDMA I.S.1-A Performance Grade: Heavy Duty,
LIGHT FRAMES
2.5
A
Wood Beads for. Ught Openings in Wood Doors: Provide manufacturer's standard wood beads
unless otherwise indicated.
1.
2.
Wood Species: Same species as door faces,
Profile: Manufacturer's standard shape.
GLAZING
2.6
A
Glazing: Fully Tempered Float Glass: ASTM C 1048, Kind FT (fully tempered), Condition A
(uncoated) unless otherwise indicated, Type I, Class 1 (clear), Quality-03.
081416-
q
CONTRACT NO. GS 14826R
2.7
FABRICATION
A
Factory fit doors to suit frame-opening sizes indicated. Comply with clearance requirements of
referenced quality standard for fitting unless otherwise indicated.
B.
Factory machine doors for hardware that is not surface applied. Locate hardware to comply with
DHI-WDHS-3. Comply with final hardware schedules, door frame Shop Drawings, BHMA156.115-W, and hardware templates.
1.
c.
Openings: Factory cut and trim openings through doors.
1.
2.
Light Openings: Trim openings with moldings of material and profile indicated.
Glazing: Factory install glazing in doors indicated to be factory finished.
SHOP PRIMING
2.8
A.
Doors for Transparent Finish: Shop prime faces and all four edges with stain (if required), other
required pretreatments, and first coat of finish as specified in Section 099300 "Staining and
Transparent Finishing." Seal edges of cutouts and mortises with first coat of finish.
FACTORY FINISHING
2.9
A.
General: Comply with referenced quality standard for factory finishing. Complete fabrication,
including fitting doors for openings and machining for hardware that is not surface applied,
before finishing.
1.
Finish faces, all four edges, edges of cutouts, and mortises. Stains and fillers may be
omitted on bottom edges, edges of cutouts, and mortises. ·
B.
Factory finish doors.
C.
Transparent Finish:
1.
2.
3.
D.
Grade: Custom.
Finish: AWl's, AWMAC's, and Wl's "Architectural Woodwork Standards" System 11,
catalyzed polyurethane.
Staining (if required): As selected by Architect from manufacturer's full range.
Opaque Finish:
1.
2.
k
L
Coordinate with hardware mortises in metal frames to verify dimensions and alignment
before factory machining.
3.
Grade: Custom.
Finish: AWl's, AWMAC's, and Wl's "Architectural Woodwork Standards" System 11,
catalyzed polyurethane.
Color: As selected by Architect from manufacturer's full range.
081416-4
CONTRACT NO.
GS 14826R
PART 3 ~ EXECUTION
. 3.1
EXAMINATION
A. ·
Examine doqrs and installed door frames, with Installer present, before hanging. doors.
1.
· 2.
B.
3.2
Verify that installed frames comply with indicated requirements for type,. s'i:~e. location,
and swing characteristics and have been installed with level heads and plumb jambs.
Reject doors with defects.
·
Proceed with installation only after unsatisfactory conditions have been corrected.
INSTALLATION
A.
B.
Hardware: For installation, see Section 087100 "Door Hardware."
I
·r
,-
. Installation Instructions: Install doors to . comply with manufacturer's written instructions and
referenced quality standard, and as indicated.
c.
Factory-Fitted Doors: Align in frames for uniform clearance at each edge.
D.
Factory-Finished Doors: Restore finish before installation if fitting or machining is required .at
Project site.
1
ADJUSTING
3.3
A.
Operation: Rehang or replace doors that do not swing or operate freely.
B.
Finished Doors: Replace doors that are damaged or that do not comply with requirements.
Doors may be repaired or refinished if Work complies with requirements and shows no evidence
of repair or refinishing.
END OF SECTION
I
!.