CARBON STEEL SHEET
Data and Specifications
®
Cold Rolled Commercial Quality Carbon Steel Sheet - Oiled
Cold Rolled Commercial Quality Sheets are produced from rimmed, capped and
semi-killed steel and are intended for exposed or unexposed parts involving bending,
moderate drawing or forming and welding. They may be bent flat on themselves in any
direction without cracking.
Applications: Practical experience is usually sufficient to determine whether
Commercial Quality or Drawing Quality is required, otherwise, the Scribed Square Test
(ASTM A 568) can be helpful. A grid of 1” squares is marked on the section representing
the most severe draw. The squares are measured for percent increase in area after
drawing. Experience has shown that Commercial Quality is usually satisfactory if the
increase in the area is less than 25%. If more than 25%, Drawing Quality is recommended.
Analysis: C - .15 Max. Mn - .60 Max. P - .035 Max. S - .04 Max.
Mechanical Properties: (following values are average and are representative)
Commercial
Drawing
Tensile Strength (psi)
38-50,000
36-46,000
Yield Point (psi)
25-35.000
23-30,000
Elongation (% in 2”)
35-42
38-43
Weldability: Yes. Forming: Yes.
Hot Rolled – Commercial Quality Carbon Steel Sheet
Hot Rolled Commercial Quality Sheets are produced from low carbon rimmed, capped
or semi-killed steel, and are intended for uses involving simple bending or moderate
drawing and welding. They can be bent flat on themselves in any direction at room
temperature without cracking on the outside of the bent portion.
Applications: From agricultural implements to automotive equipment, blower and
ventilating systems, hot air registers, stub barrels and drums to bins and partitions.
Hot Rolled Sheets may also be used for structural purposes where mechanical property
test values are required, in which case ASTM A570 should be specified.
Analysis: C - .15 Max. Mn - .60 Max. P - .035 Max. S - .04 Max.
Weldability: Yes. Forming: Yes.
Call 24/7 through our
after hours program.
The Convenience Stores For Metal™
1•866•867•9344
metalsupermarkets.com
79
CARBON STEEL SHEET
Data and Specifications
®
Hot Rolled Pickled and Oiled Commercial Quality Carbon Steel Sheet
Pickled and Oiled Sheets should be used when the tight oxide scale present on Hot
Rolled Sheets is objectionable.
Applications: The superior smooth, clean surface is especially suited for stamping and
ordinary drawing applications.
Hot Rolled Sheets may also be used for structural purposes where mechanical property
test values are required, in which case ASTM A570 should be specified.
Analysis: C - .15 Mn - .60 Max. P - .04 Max. S - .040 Max.
Mechanical Properties: (following minimum properties apply to Grades 30 and 33)
Grade 30
Grade 33
Tensile Strength (psi)
49,000
52,000
Yield Point (psi)
30,000
33,000
Elongation (% in 2”)
(.0255” - .0635”)
21
18
(.0636” - .0971”)
24
22
(.0972” - .2299”)
25
23
Weldability: Yes. Forming: Yes.
Galvanized Steel Sheet
Steel sheets are hot dip coated with a durable protective coating of zinc. This material is
intended for uses where corrosion is a consideration and where simple bending or
moderate forming is involved. They may be bent flat upon themselves in any direction at
room temperature without cracking.
Applications: For general utility uses such as corrugated siding and roofing, culverts,
window frames, heating and ventilating ducting, cornices, eaves troughs, etc. Galvanized
sheets are sometimes painted, but when a superior paint retaining surface is desired the
use of Electrolytic Zinc Coated Sheets are recommended.
Analysis: C - .15 Max. Mn - .60 Max. P - .035 Max. S - .04 Max.
“We reduced our in-house metal
inventory by shopping at
Metal Supermarkets.
They are our one stop shopping
source for any metal we need.”
The Convenience Stores For Metal™
80
1•866•867•9344
metalsupermarkets.com
CARBON STEEL
SHEET
®
CARBON STEEL SHEET COLD ROLLED COMMERCIAL QUALITY - OILED
Gauge and Size
(Inches)
Lbs./
Sheet
26 Ga. (.0179) .750 # Sq. Ft.
36 X 120
22.50
48 X 120
30.00
24 Ga. (0.239) 1.000 # sq. Ft.
30 X 96
20.00
36 X 96
24.00
42 X 120
35.00
48 X 96
32.00
48 X 120
40.00
22 Ga. (.0299) 1.250 # Sq. Ft.
30 X 96
25.00
36 X 96
30.00
48 X 96
40.00
48 X 120
50.00
48 X 144
60.00
20 Ga. (.0359) 1.500 # Sq. Ft.
30 X 96
30.00
36 X 96
36.00
36 X 120
45.00
36 X 144
54.00
48 X 96
48.00
78 X 120
60.00
48 X 144
72.00
60 X 120
75.00
60 X 144
90.00
19 Ga. (.0418) 1.750 # Sq. Ft.
36 X 96
42.00
36 X 120
52.50
48 X 96
56.00
48 X 120
70.00
60 X 120
87.50
18 Ga. (.0478) 2.000 # sq. Ft.
30 X 96
40.00
36 X 96
48.00
36 X 120
60.00
36 X 144
72.00
48 X 96
64.00
48 X 120
80.00
48 X 144
96.00
60 X 120
100.00
16 Ga. (.0598) 2.500 # Sq. Ft.
30 X 96
50.00
36 X 96
60.00
36 X 120
75.00
Gauge and Size
(Inches)
Lbs./
Sheet
16 Ga. (.0598) 2.500 # Sq. Ft.
36 X 144
90.00
48 X 96
80.00
48 X 120
100.00
48 X 144
120.00
60 X 120
125.00
60 X 144
150.00
72 X 120
150.00
72 X 144
180.00
14 Ga. (.0747) 3.125 # Sq. Ft.
36 X 96
75.00
36 X 120
93.75
48 X 96
100.00
48 X 120
125.00
48 X144
150.00
60 X 120
156.30
60 X 144
187.50
72 X 120
181.50
72 X 144
225.00
13 Ga. (.0897) 3.750 # Sq. Ft.
36 X 96
90.00
36 X 120
112.50
48 X 96
120.00
48 X 120
150.00
48 X 144
180.00
12 Ga. (.1046) 4.375 # Sq. Ft.
36 X 96
105.00
36 X 120
131.30
48 X 96
140.00
48 X 120
175.00
48 X 144
210.00
60 X 120
218.80
60 X 144
262.50
11 Ga. (.1196) 5.000 # sq. Ft.
36 X 96
120.00
36 X 120
150.00
48 X 96
160.00
48 X 120
200.00
48 X 144
240.00
60 X 120
250.00
10 Ga. (.1345) 5.625 # Sq. Ft.
36 X 96
135.00
36 X 120
168.80
48 X 96
180.00
48 X 120
225.00
The Convenience Stores For Metal™
1•866•867•9344
metalsupermarkets.com
81
CARBON STEEL
SHEET
®
CARBON STEEL SHEET HOT ROLLED (BLACK) COMMERCIAL QUALITY
Gauge and Size
(Inches)
Lbs./
Sheet
16 Ga. (.0598) 2.500 # Sq. Ft.
36 X 96
60.00
36 X 120
75.00
36 X 144
90.00
48 X 96
80.00
48 X 120
100.00
48 X 144
120.00
14 Ga. (.0747) 3.125 # Sq. Ft.
36 X 96
75.00
36 X 120
93.75
36 X 144
112.50
48 X 96
100.00
48 X 120
125.00
48 X 144
150.00
60 X 120
156.30
60 X 144
187.50
12 Ga. (.1046) 4.375 # Sq. Ft.
36 X 96
105.00
36 X 120
131.30
36 X 144
157.50
42 X 120
153.10
48 X 96
140.00
48 X 120
175.00
48 X 144
210.00
60 X 120
218.80
60 X 144
262.50
72 X 120
262.50
72 X 144
315.00
11 Ga. (.1196) 5.000 # Sq. Ft.
36 X 96
120.00
36 X 120
150.00
48 X 96
160.00
48 X 120
200.00
48 X 144
240.00
60 X 120
250.00
60 X 144
300.00
72 X 120
300.00
72 X 144
360.00
96 X 240
835.30
Gauge and Size
(Inches)
Lbs./
Sheet
10 Ga. (.1345) 5.625 # Sq. Ft.
30 X 96
112.50
36 X 96
135.00
36 X 120
168.80
36 X 144
202.50
48 X 96
180.00
48 X 120
225.00
48 X 144
270.00
60 X 120
281.30
60 X 144
337.50
72 X 120
337.50
72 X 144
405.00
72 X 240
675.00
96 X 240
939.40
9 Ga. (.1495) 6.25 # Sq. Ft.
48 X 120
250.00
8 Ga. (.1644) 6.875 # Sq. Ft.
36 X 96
165.00
36 X 120
206.30
48 X 96
220.00
48 X 120
275.00
60 X 96
275.00
60 X 120
343.80
7 Ga. (.1793) 7.500 # Sq. Ft.
36 X 96
180.00
36 X 120
225.00
36 X 144
270.00
48 X 96
240.00
48 X 120
300.00
48 X 144
360.00
60 X 120
375.00
60 X 144
450.00
72 X 96
360.00
72 X 120
450.00
72 X 144
540.00
6 Ga. (.1943) 8.125 # Sq. Ft.
36 X 120
243.80
48 X 96
260.00
48 X 120
325.00
Order only what you need.
The Convenience Stores For Metal™
82
1•866•867•9344
metalsupermarkets.com
CARBON STEEL
SHEET
®
CARBON STEEL SHEET HOT ROLLED COMMERCIAL QUALITY - PICKLED AND OILED
Gauge and Size
(Inches)
Lbs./
Sheet
16 Ga. (0.598) 2.500 # Sq. Ft.
36 X 120
75.00
48 X 120
100.00
60 X 120
125.00
14 Ga. (.0747) 3.125 # Sq. Ft.
36 X 96
75.00
36 X 120
93.75
36 X 144
112.50
48 X 96
100.00
48 X 120
125.00
48 X 144
150.00
60 X 120
156.30
60 X 144
187.50
13 Ga. (.0897) 3.750 # Sq. Ft.
36 X 96
90.00
36 X 120
112.50
48 X 96
120.00
48 X 120
150.00
60 X 120
187.50
12 Ga. (.1046) 4.375 # Sq. Ft.
36 X 96
105.00
36 X 120
131.30
48 X 96
140.00
48 X 120
175.00
48 X 144
210.00
60 X 120
218.80
60 X 144
262.50
72 X 96
210.00
72 X 120
262.50
72 X 144
315.00
11 Ga. (.1196) 5.000 # Sq. Ft.
36 X 96
120.00
36 X 120
150.00
48 X 96
160.00
48 X 120
200.00
48 X 144
240.00
60 X 120
250.00
Gauge and Size
(Inches)
Lbs./
Sheet
11 Ga. (.1196) 5.000 # Sq. Ft.
60 X 144
300.00
72 X 120
300.00
72 X 144
360.00
72 X 160
400.00
10 Ga. (.1345) 5.625 # Sq. Ft.
36 X 96
135.00
36 X 120
168.80
48 X 96
180.00
48 X 120
225.00
48 X 144
270.00
60 X 120
281.30
60 X 144
337.50
72 X 96
270.00
72 X 120
337.50
72 X 144
405.00
9 Ga. (.1495) 6.25 # Sq. Ft.
78 X 96
200.00
78 X 120
250.00
8 Ga. (.1644) 6.875 # Sq. Ft.
48 X 96
220.00
48 X 120
275.00
7 Ga. (.1793) 7.500 # Sq. Ft.
36 X 96
180.00
36 X 120
225.00
48 X 96
240.00
48 X 120
300.00
48 X 144
360.00
60 X 120
375.00
60 X 144
450.00
72 X 120
450.00
72 X 144
540.00
6 Ga. (.1943) 8.125 # Sq. Ft.
36 X 120
243.80
48 X 96
260.00
48 X 120
325.00
We source hard to find metals.
The Convenience Stores For Metal™
1•866•867•9344
metalsupermarkets.com
83
CARBON STEEL
SHEET
®
GALVANIZED - CARBON STEEL SHEET
Gauge and Size
(Inches)
Lbs./
Sheet
28 Ga. (.018) 0.781 # Sq. Ft.
36 x 96
18.79
48 x 96
25.05
48 x 120
31.32
26 Ga. (.0217) .906 # Sq. Ft.
36 X 120
27.18
48 X 96
28.99
48 X 120
36.24
60 X120
45.30
24 Ga. (.0276) 1.156 # Sq. Ft.
36 X 96
27.74
36 X 120
34.68
48 X 96
36.99
48 X 120
46.24
48 X 144
55.49
60 X 120
57.80
22 Ga. (.0336) 1.406 # Sq. Ft.
36 X 96
33.74
36 X 120
42.18
48 X 96
44.99
48 X 120
56.24
60 X 120
70.30
20 Ga. (.0396) 1.656 # Sq. Ft.
36 X 96
39.74
36 X 120
49.68
48 X 96
52.99
48 X 120
66.24
48 X 144
79.49
60 X 120
82.80
18 Ga (.0516) 2.156 # Sq. Ft.
36 X 96
51.74
36 X 120
64.68
48 X 96
68.99
48 X 120
86.24
48 X 144
103.50
60 X 120
107.80
16 Ga. (.0635) 2.656 # Sq. Ft.
36 X 96
63.74
Gauge and Size
(Inches)
Lbs./
Sheet
16 Ga. (.0635) 2.656 # Sq. Ft.
36 X 120
79.68
36 X 144
95.60
48 X 96
84.99
48 X 120
106.20
48 X 144
127.50
60 X 120
132.80
14 Ga. (.0785) 3.281 # Sq. Ft.
36 X 96
78.740
36 X 120
98.430
36 X 144
118.10
48 X 96
105.00
48 X 120
131.20
48 X 144
157.50
60 X 120
164.10
12 Ga. (.1084) 4.531 # Sq. Ft.
36 X 96
108.70
36 X 120
135.90
48 X 96
145.00
48 X 120
181.20
48 X 144
217.50
60 X 120
226.60
60 X 144
271.90
11 Ga (.1233) 5.156 # Sq. Ft.
48 X 96
165.00
48 X 120
206.20
48 X 144
247.50
10 Ga. (.1382) 5.781 # Sq. Ft.
36 X 96
138.70
36 X 120
173.40
48 X 96
185.00
48 X 120
231.20
48 X 144
277.50
60 X 120
289.10
8 Ga. (.1681) 7.031 # Sq. Ft.
48 X 120
281.20
48 X 144
337.50
Typically coated with a G.90 (Z275) coating, however, in certain cases a G.60 (Z180) coating can be found.
The Convenience Stores For Metal™
84
1•866•867•9344
metalsupermarkets.com