Please read all instructions before installing
YMSN150/YMSN180
Motion Sensor Switch
Residential sensor
California title 24
UNIT D E S C R IP T IO N
The YMSN1 50/YMSN1 80 is a motion
sensing wall switch that turns off lighting
living and dining rooms, family rooms,
Time Delay
-Neutral
bedrooms, bathrooms and any other indoor
The YMSN1 50 /Y M S N 1 80 automatically turns
area in a residential space.
lights off after a space becomes vacant and a
- DO not allow any bare wire to
show above the connector.
p re se ttim e interval, o rtim e delay, elapses. If
based on vacancy. The sensor uses passive
infrared (PIR) technology to sense human motion
in a controlled space. If It does not sense
human motion, It determines that the area is
vacant and automatically turns the lights off.
n order to keep the lights on when someone
is in the room, the sensor must have a clear
view of occupants. Obstructions such as
&
S P E C IF I C A T IO N S
Voltage.........................................120VAC, 60Hz
It can control most standard lamp types,
lights are left on and no motion is detected for
including incandescent, fluorescent, compact
the time delay selected (factory default = 1 5
fluorescent (CFL), magnetic low voltage
minutes), the YMSN150/YMSN1 80
(MLV), electronic low voltage (ELV)
automatically turns light off.
O P E R A T IO N
Manual-ON, Automatically OFF
furniture blocking the sensor's lens may
Users must turn lights on by pushing the
prevent occupancy detection.
Standby button. Lights will not turn on
Note:
autom atically with occupancy. However, fora
Windows, glass shower doors, etc. Will
grace period of 30 seconds a f t e r s h u t - o f f , t h e
o b s t r u c t t h e Y M S N I 5 0 / Y M S N 1 8 0 's v ie w
Y M S N 1 5 0 / Y M S N 1 8 0 w ill automatically
and may p r e v e n t detection. Through the
turn the load back on when motion is detected
A m p e re ............................5A
Y M S N 150/Y M S N 1 80's mode s e le c tio n , the
Load (single pole circuit)
user can s p e c ify the time delay th a t lights
Manual-ON, Manual-OFF
will be left on after the last motion is
If users turn lights off by pushing the Standby
Incandescent or fluorescent........... 0-600 Watts
Time Delay A djustm ent......... 1 minute to 30minutes
Power C onsum ption.............. 0 .9 2 W m a x im u m
detected (see sensor Adjustment &
Programming section).
Environment........Residential Indoor use only
Tools Needed
or white to neutral;
button.The Y M S N 150/Y M S N 180 will not
automatically turn the load back on when
motion is detected within a grace period of 30
Insulated Screwdriver
The YMSN1 50 /Y M S N 1 80 is d e s ig n e d t o
seconds. (This function is used for someone
Wire Strippers
replace a single pole switch. It is ideal for
sleeping in the bedroom.)
CAUTION:TURN THE POWER OFF ^
AT THE CIRCUIT BTEAKER BEFORE WIRING.
IN S T A L L A T IO N :
Caution;
A neutral c o n n e c tio n is
sensor o p e ra tio n .
3. A t t a c h the s e n s o r t o th e w a ll box by
required
i n s e r t i n g screws into the two wide holes
for
A q u a l i f i e d e le c tr ic ia n s h o u ld be c o n s u lte d
r e g a r d in g the ava ila b ility of a neutral in your
p a rtic u la r installation:
1. Make sure t h a t p o w e r has been tu rn e d
off at the c ir c u it bre a ker.
2. C o n n e c t the e x is tin g w ir e s to the s e n s o r
te r m in a ls .
• Hot
or b la c k to Line;
or red to load;
or green to ground;
• Load
•Ground
on the top and bottom of the a tta c h e d
metal b ra c ke t.
Line th e m up w ith the
h o le s in the wall box and tig h te n .
4. Turn on the c ir c u it b re a ker. Push the
S ta n d b y b u tto n and the lig h ts will turn on
# 1 2 - #14 AWG
Strip Gauge
Wire insert
Sol i d CU wi r e onl y
Max 2.0 Nm T o r q u e
Optional
wire wrap
insert or w r a p wire as shown.
Tighten s c r e w i n the clo ckwis e direction.
5. A U L listed c o v e r plate is in s ta lle d and
used to c o v e r the m otion s e n s o r sw itch.
SENSOR ADJUSTMENT &
PROGRAMMING
s e le c tio n is re a ch e d , slide the P ro g ra m
Mode S w itc h ba ck to the N p o s itio n .
3.The tim e s of b u z z e r s o u n d in d ic a te the
c u r r e n t tim e s d e la y s e le c tio n .
If the l i g h t i s o n and the s e n s o r re m a in s in
make m o tio n in the s e n s o r 's v ie w w ith in
p ro g ra m Mode, the b u z z e r will s o u n d
30 s e c o n d s of the s h u t-o ff.
c o n t in u a lly until re s u m e to the N po sition.
Lights turn OFF after 15 minutes:
WIRING
I . S e n s o r i s i n P ro g ra m Mode.
2.See S E N S O R A D J U S T M E N T &
Custom setup features are intended for
installing personnel. Therefore, the program
o
Mode switch is located behind the cover plate
Neutral
Ground
green
w hite
To enable the programming mode, the slide
1
Programming the
YMSN150/YMSN180
c o v e re d by the sw itch c o v e r plate) to the
P (p r o g r a m ) po sitio n . Make note of how
m any t im e s the b u z z e r so u n d . The
n u m b e r of s o u n d s in d ic a te s the c u r r e n t
t im e s d e la y s e le c t io n . ( s e e P ro g ra m Mode
S e le c tio n s b e lo w )
2 .P re s s the S ta n d b y button to a d v a n c e
t h r o u g h the delay s e le c tio n s , the t im e s
will be c h a n g e d from
one to six in cycle. W h e n
Load
Red
O
1 .Slide the P ro g ra m Mode S w itch (n o r m a lly
of b u z z e r s o u n d
1 .Press S ta n d b y button, lig h ts s h o u ld turn
Hot
Black
the d e s ire d
4 .The t i m e s o f b u z z e r s o u n d i n d i c a t e
Time Delay
Buzzer Sounds
1 m inute d e la y
Once:
5 m in u te s d e la y
Twice:
1 0 m in u t e s d e la y
T h re e tim es:
1 5 m in u t e s delay
Four tim e s :
20 m in u te s delay
Five tim e s:
30 m in u te s delay
Six tim e s:
* F a cto ry d e fa u lt
Note:
m
Neutral
w hite
Load
S in g le -s e n s o r w iring
S w itc h in the P po sitio n . The Y M S N 1 5 0 /
Y M S N 1 8 0 will only o p e ra te p r o p e r ly in the
N p o s itio n .
2 .Make c e r ta in t h a t the c ir c u it b r e a k e r is on
and fu n c tio n in g .
3 .C h e c k s e n s o r wire c o n n e c t i o n s to the load
COVERAGE PATTERNS
5.C h e c k the lamp.
The YMSN1 50/YM SN180 h a s a c o v e r a g e
Lights turn off while the space is occupied.
r a n g e o f 1 5 0 / 1 8 0 d e g r e e s a n d a m a x im u m
1 .Make sure n o th in g is b lo c k in g the
c o v e r a g e c a p a t i c y and o p t im a lly d e te c t
Do not le a v e the p r o g r a m M ode
on.
4 .C h e c k w irin g c o n n e c t i o n s to the sensor.
coverage area of 400 s q .ft. To m a in t a in its
P ro g ra m Mode Switch.
3 .Put the sw itch in the N mode.
Lights will not turn on:
O
switch must be in the P position.
TROUBLE SHOOTING
P R O G R A M M IN G for the lo c a tio n of the
s e n s o r s lens.
2 .If the o c c u p a n t s have been very
m otion, t h e Y M S N I 50 /Y M S N 1 80 m u s t have
m o t io n le s s for the d u ra tio n of the time
a c l e a r a n d u n o b s t r u c te d view.
delay, th is is norm al ope rati on.To
a u t o m a t ic a l ly turn the lig h ts back on,