105U-1,2,3,4 Multi I/O
I/O Point to Multi-Point Networking
Applications
• High level alarms
• Security gate control
• Emergency shower notification
• Flow meter monitoring
• Storage tank monitoring
• Pipeline cathodic protection
• Pump stop-start
• Lighting bank control
• Weather station reporting
• Bearing condition monitoring
Specifications
Transmitter/Receiver
Description
The ELPRO multi-I/O products are two-way communication devices which
transmit signal values by radio (specifying the value and I/O output channel)
to a receiving module. The receiving module then decodes the message,
generating/re-creating the value at the specified I/O channel outputs.
ELPRO 105U series products have four differing I/O versions and can multihop repeat five times. When combined with ELPRO’s 115S series products
or gateway products, the 105U series can accommodate changing I/O and
data-bus/protocol requirements.
Modulation
DFSK(1)
Transmit Power
148 - 174MHz, 0.1 - 5W
220 - 235MHz, 0.1 - 5W
360 - 512MHz, 10mW - 5W
869.525MHz, 500mW
869.875MHz, 5mW
Receiver Sensitivity
400MHz: –112dBm
868MHz(2): –108dBm: 869.525/869.875MHz
Data Rate
400MHz: 3.6kbps
868MHz(2): 19.2kbps, forward-error correction
Line Of Sight Range(3)
400MHz: 10mW EIRP to 2km; 500mW EIRP to 10km;
5W EIRP to 50km
868MHz(2): 5km (500mW); 1km (5mW)
Antenna Connector
400MHz: BNC Female Coaxial with gas discharge arrestor
868MHz(3): SMA Female Coaxial
Features
• AC/DC/battery power options, UPS battery charger and solar re.g.,ulator.
• Multiple I/O channels for monitoring and/or controlling field devices with
set-point option availability*. Additional internal I/O points include low/
normal supply and battery voltage (analog).
• I/O inputs can be linked to single or multiple I/O outputs (up to 95 units in
a system).
• Point to multi-point communications combining exception-reporting, selfchecking and data encryption.
• Communication-failure notification and diagnostics including radio path
measurement, communications logging, verification of input/output values.
• User-friendly configuration software.
• Class I Division 2 hazardous areas approval (USA/Canada).
*Setpoint status generated by comparing analog inputs to high and low setpoints.
Available on AI1 of 105U–1 units, and AI1-4 of 105U–2 units.
Input/Output
Digital Input
Voltage free/NPN, wetting current 0.5mA
105U-4 have Four inputs, 12 selectable I/O
Surge protected (not isolated)
Digital Output
105U-1: Four relay contacts. From A - AC 50V: 5A/DC 30V: 2A
105U-2: One FET output 30Vdc/500mA
105U-3: Eight FET output 30Vdc/500mA
105U-4: Up to 16 FET output (4 outputs + 12 selectable I/O)
Analog Input
Floating differential inputs, common mode, voltage 27V
24Vdc for external loops provided, digital filtering 1 sec
105U-1: Two 4 - 20mA AI, resolution 15 bit, accuracy 0.1%
Over range indication 2 - 25mA
105U-2: Six 0 - 20mA AI, resolution 12 bit, accuracy 0.1%
Over range indication 0 - 25mA
Note: Specifications subject to change.
1) DFSK - Digital Frequency Shift Key.
2) 868MHz (869.525MHz: 500mW; 869.875MHz: 5mW).
3) Actual radio distances dependent on terrain/obstacles.
Continued on back.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11833
Page 1 of 3
Data Sheet # 7906
105U-1,2,3,4 Multi I/O
I/O Point to Multi-Point Networking
Specifications
Terminal Strip
Removable: up to 2.5mm2 (12 AWG)
EMC: FCC Part 15, AS3548, EN 301 489
Radio: EN 300 220, FCC Part 90, RSS 119, AS4295,
AS4768.1, EN 300 113
Safety: EN 60950, Class I Division 2 hazardous areas (USA/
Canada)
Analog Output
Current sink to common, max loop voltage 27V, max loop
resistance 1000ohms
105U-1: Two 4 - 20mA AO, resolution 15 bit, accuracy 0.1%
Over range indication 0.5 - 25mA
105U-3: Eight 0 - 20mA AO, resolution 12 bit, accuracy 0.1%
Over range indication 0 - 20.5mA
Approvals
Pulse Input
As per Digital Input specifications above. Max pulse rate
1000Hz, pulse width min 5ms
105U-1: One PI, terminated at DI 1
105U-2: Four PI, terminated at DI 1 - 4. First DI/PI max
1000Hz, pulse width min 0.5ms. Two, three, four DI/PI’s max
100Hz, pulse width 5ms
105U-4: Four PI, terminated at DI 1 - 4. First DI/PI max
1000Hz, pulse width min 0.5ms
Nominal Supply
12-24Vac/15-30Vdc: over-voltage/reverse power protected
Quiescent Current
At 12Vdc: 85mA; +10mA/active digital input; +25mA/active
digital output; +2 analog I/O loop (mA)
Transmission Current
450mA @ 13.8Vdc (0.5W)
600mA @ 13.8Vdc (1W)
800mA @ 13.8Vdc (2W)
1.25A @ 13.8Vdc (5W)
PO’s as per FET Digital Outputs specifications above
FET DO/PO 30Vdc, 500mA, max pulse rate 100Hz
105U-1: One PO
105U-3 and 105U-4: Four PO, terminated at DO 1 - 4
Battery Supply
11.5-15.0Vdc (battery supply volts internal I/O value)
Pulse Output
Serial Port
Power Supply
Battery Charging Circuit 1.2-12AHr battery: max charge current 0.7A at >12V
Solar Regulator
Direct connection solar panel (to 30W)/solar battery 100AHr
Loop Supply
Internal DC/DC converter: 24Vdc/150mA
Note: Specifications subject to change.
RS232
9pin DB9 female connector
RS485
Terminal connector (serial expansion only, cable to 1200m)
Data Rate
9600 baud, 8 bits, no parity, 1 stop bit
Protocols Supported
ELPRO WIBnetTM auto acknowledgement up to 4 retries,
CRC error checking
User Configuration
E-Series configuration utility
System Address
Configurable system address
Configurable
Parameters
Individual I/O mappings, analog and digital debounce, update
time, analog set points and sensitivities, output reset times
Reported Diagnostics
RSSI, comms logging, I/O status
Security
64 bit encryption on radio and Serial
PWR (Power)
Mains/battery power supply available
I/O LED markers
I/O inputs and outputs status
OK
Module OK
TX
Radio transmitting
RX
Radio receiving
LED Indication
General
Size
5.1”x 7.3”x 2.4” (130 x 185 x 60mm)
Weight
2.2lbs (1Kg)
Temperature
105U-150,220,400MHz: -30 to +60°C (-22 to 140°F)
105U-869MHz: -40 to +60°C (-40 to 140°F)
Humidity
0-99%RH Non-Condensing
Housing
Extruded aluminum
Mounting
DIN rail mounting
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11833
Page 2 of 3
Data Sheet # 7906
105U-1,2,3,4 Multi I/O
I/O Point to Multi-Point Networking
Ordering
Accessories
To order, select product code from the table and specify country of application.
The following accessories can assist with compatibility when commissioning.
Product Code
Description
Frequency
RF Power
105U-1-150-5W
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
148-174MHz
105U-1-220-5W
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
220-235MHz(2) 0.1 - 5W
105U-1-xxx(1)-5W
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
360-512MHz(2)
(2)
Product Code
Description
Data
Sheet #
0.1 - 5W
0.5 - 5W
105U-1-xxx(1)-500M
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
360-512MHz(2)
10 - 500mW
105U-1-868-500M
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
869.525MHz
500mW
105U-1-868-5M
Wireless I/O 4DI, 4DO, 2AI, 2AO,1P0
869.875MHz
5mW
105U-2-150-5W
Wireless I/O 4DI, 1DO, 6AI, 4PI
148-174MHz(2)
0.1 - 5W
105U-2-220-5W
Wireless I/O 4DI, 1DO, 6AI, 4PI
220-235MHz(2) 0.1 - 5W
105U-2-xxx(1)-5W
Wireless I/O 4DI, 1DO, 6AI, 4PI
360-512MHz(2)
0.5 - 5W
105U-2-xxx(1)-500M
Wireless I/O 4DI, 1DO, 6AI, 4PI
360-512MHz(2)
10 - 500mW
105U-2-868-500M
Wireless I/O 4DI, 1DO, 6AI, 4PI
869.525MHz
105U-2-868-5M
Wireless I/O 4DI, 1DO, 6AI, 4PI
105U-3-150-5W
Antennas 148 - 174MHz
UDP150-5
Dipole Antenna: BNC Male, 0dBi gain, 16’ (5m) Coaxial cable
7939
Antennas 220 - 235MHz
UDP200-C
Dipole Antenna: N-type Female, 0dBi gain
7939
UDP200-3
Dipole Antenna: BNC Male, 0dBi gain, 9’ (3m) Coaxial cable
7939
UDP400-C
Dipole Antenna: BNC Male, 0dBi gain, 9’ (3m) Coaxial cable
7940
UDP400-3
Dipole Antenna: N-type Female, 0dBi gain, 9’ (3m) Coaxial cable
7940
YU-3/400
Yagi Antenna: 3 element, N-type, 10dBi gain
7940
YU-6/400
Yagi Antenna: 6 element, N-type, 9dBi gain
7940
500mW
YU-16/400
Yagi Antenna - 16 element, N-type, 15dBi gain
7940
869.875MHz
5mW
BU-3/400
Collinear Antenna: N-type Female, 5dBi gain
7940
Wireless I/O, 8DO, 8AO, 4PO
148-174MHz(2)
0.1 - 5W
BU-6/400
Collinear Antenna: N-type Female, 8dBi gain
7940
105U-3-220-5W
Wireless I/O, 8DO, 8AO, 4PO
(2)
220-235MHz
0.1 - 5W
105U-3-xxx(1)-5W
Wireless I/O, 8DO, 8AO, 4PO
360-512MHz(2)
0.5 - 5W
CFD890EL
Dipole Antenna: SMA, 2dBi, 16’ (5m) RG58, bracket
7942
105U-3-xxx -500M
Wireless I/O, 8DO, 8AO, 4PO
360-512MHz
10 - 500mW
SG900EL
Collinear Antenna: N-type Female, 5dBi gain
7942
105U-3-868-500M
Wireless I/O, 8DO, 8AO, 4PO
869.525MHz
500mW
SG900-6
Collinear Antenna: N-type Female, 8dBi gain
7942
105U-3-868-5M
Wireless I/O, 8DO, 8AO, 4PO
869.875MHz
5mW
DG800-5
Whip Antenna: SMA Male, -2dBi gain, 16’ (5m) RG174, bracket
7942
105U-4-150-5W
Wireless I/O, 16DIO, 4DO, 4DI
148-174MHz
0.1 - 5W
YU6/870
Yagi Antenna: 6 element, N-type, 9dBi gain
7942
105U-4-220-5W
Wireless I/O, 16DIO, 4DO, 4DI
105U-4-xxx -5W
(1)
(2)
(2)
Antennas 360 - 512MHz
Antennas 869MHz
Cables
(2)
220-235MHz
0.1 - 5W
Wireless I/O, 16DIO, 4DO, 4DI
(2)
360-512MHz
0.5 - 5W
CC3/10/20-SMA
Coaxial Cable Kit - 10’ (3m)/33’ (10m)/66’ (20m), N-type to SMA
7932
105U-4-xxx -500M
Wireless I/O, 16DIO, 4DO, 4DI
360-512MHz
10 - 500mW
CC10/20-BNC
Coaxial Cable Kit - 33’ (10m)/66’ (20m), N-type to BNC
7932
105U-4-868-500M
Wireless I/O, 16DIO, 4DO, 4DI
869.525MHz
500mW
CCTAIL-SMA-F/M
Coaxial Cable Tail - 2’ (600mm), SMA to N-type Female/Male
7932
5mW
CCTAIL-BNC-M
Coaxial Cable Tail - 2’ (600mm), BNC to N-type male
7932
SER-DB9
Serial RS232 Cable - DB9 male to DB9 female straight through
7932
(1)
(1)
105U-4-868-5M
Wireless I/O, 16DIO, 4DO, 4DI
(2)
869.875MHz
Note: Available RF power and frequency may vary depending on country of application.
1) Represents frequency band (370, 390, 410, 430, 440, 460, 480, 500).
2) Typically licensed - specify Tx/Rx frequencies, RF power and channel spacing.
Surge Diverters
CSD-SMA-2500
SMA Surge Diverter for use with CC10, CC20 - SMA
7936
CSD-N-6000
Coaxial Surge Divertor, Bulkhead N Female to N Female
7936
MA15/D/1/SI
Power Supply Surge Diverter, 110Vac/15A
7936
IOP32/IOP32D
Signal Surge Diverter, 2 wire/4 wire
7936
Power Supplies
PS-DINAC-12DC
DIN Rail Power Supply, 100 - 250Vac, 12Vdc/2.5A
7935
PS-DINAC-24DC
DIN Rail Power Supply, 100 - 250Vac, 24Vdc/2A
7935
Mounting Brackets
BR-YAGI-KIT
Mounting Bracket Kit for Yagi Antenna
7933
BR-COL-KIT
Mounting Bracket Kit for Collinear Antenna
7933
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
©2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
BU-SB11833
Page 3 of 3
Data Sheet # 7906