DE-IG1
FLOETH
DC/DC Converter
ELECTRONIC
AC/DC Inverters
Delay-Lines
Pulsetransformers
Burst & Surge Filters
Hamonic Filters
Switching Power Supplies
Am Malfinger Steig 13
86920 Denklingen/Obb.
Germany
FLOETH
Tel.: 08243-9693-0
Fax: 08243-9693-33
www.floeth-electronic.com
ELECTRONIC
Issue 4.0 January 2004
DE-IG1
Single IGBT Module Driver Interface Card
FEATURES
Accomodates HV2-15, HVx-30A and HVx-30I
Electronic IGBT Driver Modules
■
ORDERING INFORMATION
Floeth
Order As:
Interface Card only:-
■
Available as Board Only or as Complete Assembly with
Driver Module
DE-IG1
■
Suitable for Standard IGBT Modules at 1200V and 1700V
Driver Module/Interface Card assembly:-
■
HP Fibre Optic Link Interface Connections
HV2-15 / DE-IG1
- 2300V AC rms partial discharge free
■
Single supply voltage (0V, +15V)
■
Isolated Failure Feedback
■
High dv/dt Immunity of 100kV/µs
HV3-30I / DE-IG1 or HV3-30A / DE-IG1
- 3000V AC rms partial discharge free
■
Short Circuit and Overcurrent Protection of IGBT
■
Undervoltage Lockout
HV4-30I / DE-IG1 or HV4-30A / DE-IG1
- 4000V AC rms partial discharge free
■
+15V and –15V Gate Voltages
HV5-30I / DE-IG1 or HV5-30A / DE-IG1
- 5000V AC rms partial discharge free
■
Duty Cycle 0 to 100%
Note: When ordering, please use the complete part number.
HV2-30I / DE-IG1 or HV2-30A / DE-IG1
- 2300V AC rms partial discharge free
APPLICATIONS
■
Industrial Drives
■
Railway Traction Drives and Auxiliaries
■
Power Supplies
■
Wind Turbines
This datasheet features an IGBT interface card designed and
manufactured by Floeth Electronic. The DF-IG1 is designed for
use with 140x130mm single switch standard IGBT modules. The
interface card accepts the IGBT driver module (HV2-15, HVx30A and HVx-30I series) designed and manufactured by Floeth
Electronic. The HV2-15 and HVx-30x series are compact single
channel intelligent gate drive modules. More information is given
in publication AN5609 - HVx-30A/HVx-30I Floeth Electronic
IGBT Driver Module and AN5706 - HV2-15 Floeth Electronic
IGBT Driver Module.
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
1/3
DE-IG1
FLOETH
ELECTRONIC
JUMPER SETTINGS
Pin No. Description
Note
Standard operation mode / single switch application
J2
Connected - Pulls Pin 33 to COM
Not connected
Gate driver Output in antiphase with Input.
No input signal (LOW), gate pulled LOW (–15V).
Gate driver Output in phase with Input.
Output signal is HIGH (+15V).
J3
Connected - Pulls Pin 34 to COM
Driver is disabled during a fault condition - fault reported on SO.
J4
DO NOT CONNECT!
Short circuit will result between +15V and COM if connected
Multiple switch - series or parallel operation
J2
Connected - Pulls Pin 33 to COM
Not connected
Gate driver Output in antiphase with Input.
No input signal (LOW), gate pulled LOW (–15V).
Gate driver Output in phase with Input.
Output signal is HIGH (+15V).
J3
DO NOT CONNECT!
J4
Connected - Will set Pin 34 to high (+15V) Driver continues to function during a fault condition - fault is reported on
SO.
2/3
Short circuit will result between +15V and COM if connected
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
DE-IG1
FLOETH
ELECTRONIC
OUTLINE DETAILS
This information is given for reference purposes only and should not be scaled. All dimensions in mm, unless stated otherwise.
69
48
10
G
E
C8
C
D3
D2
+
D7
+
+
C6
J3
J4
J2
Rx
D5
D6
D4
C7
C2
C5
C4 D8
D1
R1
C3
R4
106
111
115
Tx
3.9
TOP
C1
+
–
3.9
+
75
Ø4.5
All 5 fixing holes
plated through vias.
Fig. 2 Outline details
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
3/3