Note: Information and specification are subject to change without prior notice. HP OpenView and Windows are registered trademarks of Hewlett-Packard and Microsoft respectively. WitLink and WtView are trademarks of Witcom Ltd. © 2002 Wtcom Ltd. All rights reserved. E1 1 23 4 Indoor Unit (IDU) The WitLink-2000® is the first radio system to incorporate front-loadable plug-ins to support diversified network requirements. The WitLink-2000® feature of auto-detecting the Plug-In type allows the end-users to seamlessly adapt to existing network requirements. Software-controlled "reduced capacity" utilizes Spectrum-on-Demand. WitLink-2000® may scale from low capacity/low spectrum (such as 4*DS1/E1) to medium capacity / larger spectrum (such as DS3/E3) without the need of existing hardware modification. Furthermore, these changes are field upgradeable. The Ethernet 10/100Base-T interface plug-in supports wireless bridge implementations. These implementations are ideally suited for Service Providers (ISP’s video-on-demand, MTU’s) and private networks. This plug-ins features two 10/100Base-T ports (Full Duplex) + 4*DS1 (E1) ports. The plug-Ins supports full transparent bridging. The PDH Plug-Ins may be used up to a maximum capacity of DS3+4*DS1 (E3+1E1). Modular plug-in interfaces, 6Mbps to 52 Mbps Wireless Bridge – 2*10/100Base-T+4*DS1 Wireless Bridge – 2*10/100Base-T+4*E1 PDH – DS3+16*DS1, E3+16*E1, 4*E1/8*E1 Common IDU Specifications IDU to ODU Connection Number of cables Type Impedance Recommended Cable Maximum distance IDU Connector type Modem Modulation type Forward error correction Environmental Temperature (operation) Relative humidity Power Requirements DC source DC consumption Mechanical Dimensions Weight Standard Interfaces Auxiliary data channel Relay alarm outputs & external inputs Touch keys and display interface Network management 1+1 redundancy Standards Safety EMC/EMI Single Coaxial Cable RG-8 50 Ohms unbalanced Belden 9913 (RG-8) or equivalent Up to 300m (1000ft) "N" type Female connector 4FSK Reed Solomon Code (correction of up to 20 bytes out of 255 bytes frame) -5ºC to +45ºC 95% at 40ºC 22 to 60Vdc, polarity insensitive 20 Watt 1.75" (1U) x19" x12" (HxWxD) (fits standard 19" equipment rack) 10 lbs, 4.6 kg EIA RS232 data in port; shielded RJ45 / Optional EOW service channel D- type, 25 pin, female; 5 relays floating from “C” relay; 4 floating inputs 5 touch keys & 16x2 character LCD - standard feature 10Base- T Ethernet management port: shielded RJ45 NMS- IN port: RS232 SNMP, shielded RJ45 110 pin, female CE mark EN60950 (ETSI); NRTL ANSI/ UL1950 (FCC) EN 300 386-2 (ETSI), EN 300 385 (ETSI); FCC Part 15 WitLink-2000 Technical Specifications Rev-02 Outdoor Unit (ODU) and Antennas The WitLink-2000® flexible ODU/antenna combination is available in all frequencies within 7~38GHz range, with ETSI and FCC approved versions. The radio frequency components of the ODU are contained within a hermetically-sealed enclosure. The ODU may be press fitted onto the antenna and can be mounted on a mast, tower or rooftop. This flexible design allows the ODU to be disconnected from the antenna without affecting antenna alignment, and directly mounted to the antenna without the need for use of any waveguides or adaptors. One coaxial cable is used to connect the ODU to the IDU. Power is provided to the ODU via this single cable. The compact, aesthetic WitLink-2000® ODU is capacity independent as well, resulting in quicker deployment and redeployment, simplified logistics and reduced spare part requirements. Common ODU Specifications General Frequency stability Frequency channel selection Environmental Temperature (operation) Relative humidity Altitude Power Requirements DC source DC consumption Mechanical Dimensions Weight Standards Environmental Safety ±5ppm Software-controlled -33ºC to +55ºC All weather protection (up to 100%) Up to 15,000 feet AMSL (4,500 m) 22 to 60Vdc, supplied by the IDU 23 Watt / 32 Watt for high power 9.05" x 6.9" (23x17.5 cm) (DxH) 9.6 lbs, 4.9 kg ETS-300-019-2-4 CE mark EN60950 (ETSI); NRTL ANSI/ UL1950 (FCC) Antenna Specifications – (Direct Mount or Indirect Mount via Wave guide) Type Parabolic, high performance, all frequencies Diameters 1'(30cm), 1.5’(45cm), 2'(60cm), 3'(90cm), 4'(120cm), 6'(180cm) 7/8/13/15GHz (2, 3, 4, 6 feet) 18/23GHz (1, 1.5, 2, 3, 4 feet) Diameter per Frequency 26GHz(1, 1.5, 2, 3 feet) 38GHz (1, 1.5, 2 feet) Polarization Horizontal or vertical WitLink-2000 Technical Specifications Rev-02 System Specification (Table I) System Parameters 7/8 GHz ETSI 13 GHz ETSI 15 GHz ETSI 18 GHz FCC & ETSI General Operating at Frequency Tx / Rx Spacing RF connector Transmitter Tx output Power Output power Control range ITU emissions designators per capacity 7.125 – 8.5 GHz 12.75 – 13.25 GHz 14.40 – 15.35 GHz 17.70 – 19.70 GHz 119,154,161,311 MHz 266 MHz 315, 420, 728 MHz FCC 1560 MHz ETSI 1010 MHz Waveguide Flange (WR-112) Waveguide Flange (WR-62) Waveguide Flange (WR-62) Waveguide Flange (WR-42) +27dB +25dB +25dB Software Controlled; Mute – 45 dBm +35 dBm +35 dBm +37 dBm 7M00F7W 14M0F7W 28M0F7W 56M0F7W 7M00F7W 14M0F7W 28M0F7W 56M0F7W 7M00F7W 14M0F7W 28M0F7W 56M0F7W +20dB +24dBm for High power +30 dBm FCC ETSI 5M50F7W 13M8F7W 10M0F7W 27M5F7W 20M0F7W 55M5F7W 40M0F7W Receiver FCC Sensitivity -6 @10 BER 4*E1 8*E1 16*E1 E3 E3+E1 4*E1 -81 dBm 8*E1 -78 dBm 16*E1 -75 dBm E3 -75 dBm E3+E1 -73 dBm -82 dBm -79 dBm -77 dBm -77 dBm -75 dBm Max input signal level System Gain 4*E1 -81 dBm 8*E1 -78 dBm 16*E1 -75 dBm E3 -75 dBm E3+E1 -73 dBm 8*DS1 16*DS1 DS3 DS3+2*DS1 DS3+4*DS1 -79dBm -76dBm -73dBm -73dBm -72dBm ETSI 8*E1 16*E1 E3 E3+E1 -77dBm -74dBm -74dBm -72dBm -10 dBm @ 10-3 BER FCC 4*E1 8*E1 16*E1 E3 E3+E1 Standards RF channel Arrangement Complies with 109 dB 106 dB 104 dB 104 dB 102 dB 4*E1 8*E1 16*E1 E3 E3+E1 106 dB 103 dB 100 dB 100 dB 98 dB 4*E1 106 dB 8*E1 103 dB 16*E1 100 dB E3 100 dB E3+E1 98 dB 8*DS1 16*DS1 DS3 DS3+2*DS1 DS3+4*DS1 99 dB 96 dB 93 dB 93 dB 92 dB ETSI 8*E1 16*E1 E3 E3+E1 97 dB 94 dB 94 dB 92 dB ITU-R Rec.F.385-6 ITU-R Rec.F.386-6 ITU-R Rec.F.497-6 ITU-R Rec.F.636-3 ITU-R Rec.F.595-6 ETSI EN 301 216V1.2.1 ETSI EN 301 128 ETSI EN 301 128 ETSI EN 301 751 ETSI EN 301 128 FCC Part 101 WitLink-2000 Technical Specifications Rev-02 System Specification (Table II) System Parameters General Operating at frequency Tx / Rx Spacing RF connector Transmitter Tx output power Output power Control range ITU emissions designators per capacity 23 GHz FCC & ETSI 26 GHz ETSI 21.20 – 23.60 GHz 24.50 – 26.50 GHz FCC 1200 MHz ETSI 1008, 1232 MHz Waveguide Flange (WR-42) +20 dBm Waveguide Flange (WR-42) FCC 38.60 – 40.00 GHz ETSI 37.00 – 39.50 GHz FCC 700 MHz ETSI 1200 MHz Waveguide Flange (WR-28) +20 dBm +30 dB ETSI 7M00F7W 14M0F7W 28M0F7W 56M0F7W FCC 7M00F7W 12M5F7W 25M0F7W 50M0F7W 1008 MHz 38 GHz FCC & ETSI Software Controlled; Mute – 45 dBm +30 dB 7M00F7W 14M0F7W 28M0F7W 56M0F7W +17 dBm +27 dB FCC ETSI 7M00F7W 7M00F7W 12M5F7W 14M0F7W 25M0F7W 28M0F7W 50M0F7W 56M0F7W Receiver FCC FCC Sensitivity -6 @10 BER 4*DS1 8*DS1 16*DS1 DS3 DS3+2*DS1 DS3+4*DS1 -81 dBm -79 dBm -76 dBm -74 dBm -74 dBm -72 dBm ETSI 4*E1 8*E1 16*E1 E3 E3+E1 -81 dBm -78 dBm -75 dBm -75 dBm -73 dBm Max input signal level System Gain 4*E1 8*E1 16*E1 E3 E3+E1 -81 dBm -78 dBm -75 dBm -75 dBm -73dBm 4*DS1 8*DS1 16*DS1 DS3 DS3+2*DS1 DS3+4*DS1 ETSI 4*E1 8*E1 16*E1 E3 E3+E1 FCC FCC ETSI 4*E1 101 dB 8*E1 98 dB 16*E1 95 dB E3 95 dB E3+E1 93 dB Arrangement Complies with -78 dBm -75 dBm -72 dBm -72 dBm -71 dBm -10 dBm @ 10-3 BER 4*DS1 101 dB 8*DS1 99 dB 16*DS1 96 dB DS3 94 dB DS3+2*DS1 94 dB DS3+4*DS1 92 dB Standards RF channel -78 dBm -75 dBm -72 dBm -70 dBm -70 dBm -69 dBm 4*E1 95 dB 8*E1 95 dB 16*E1 98 dB E3 101 dB E3+E1 93 dB 4*DS1 8*DS1 16*DS1 DS3 DS3+2*DS1 DS3+4*DS1 95 dB 92 dB 89 dB 87 dB 87 dB 86 dB ETSI 4*E1 8*E1 16*E1 E3 E3+E1 96 dB 93 dB 90 dB 90 dB 89 dB ITU-R Rec.F.637-3 ITU-R Rec.F.748-3 ITU-R Rec.F.749-1 ETSI EN 300 198 FCC Part 101 ETSI EN 300 431 ETSI EN 301 390 ETSI EN 300 751 ETSI EN 300 197 ETSI EN 301 390 ETSI EN 301 751 FCC Part 101 WitLink-2000 Technical Specifications Rev-02 Interface Plug-ins Component Technical Parameters Two 10/100Base-T+4DS1(4E1) PIN-42042 (PIN-52042) DS3 +16DS1 (E3+16E1) PIN-12161 (PIN-22161) 4E1/8E1 PIN-22040 (PIN-22080) Digital Interface IEEE 802.3,802.3u standard Compliance: DS1(E1) per ITU-T Rec.G.703 DS1(E1)&DS3(E3) per ITU-T Rec.G.703 E1 per ITU-T Rec.G.703 Digital Input/Output Connector 10/100Base-T-shielded RJ45, 100Ω; DS1(E1)-shielded RJ48, 100Ω (120Ω) Digital Line Code DS1-AMI / B8ZS E1-HDB3 Digital Capacity Configurable Capacities Channel Spacing 23/38GHz FCC Channel Spacing 18GHz FCC Channel Spacing 13/15/23/26/38GHz ETSI Channel Spacing 18GHz ETSI 2x10/100Base-T ports+4DS1 (4E1) wayside channels 2x10/100Base-T+4DS1 2x10/100Base-T+1,2,4E1 12.5MHz, 25MHz, 50MHz 10MHz, 20MHz, 40MHz DS1(E1)-shielded RJ48, 100Ω (120Ω) balanced, DS3(E3) – Coax BNC, 75Ω unbalanced DS1-AMI/B8ZS, DS3-B3ZS E1- HDB3, E3-HDB3 Up to 16DS1 (16E1) or DS3+4DS1 (E3+1E1) 4/8/16DS1, DS3, DS3+4DS1 4/8/16E1, E3, E3+1E1 7.5MHz, 12.5MHz, 25MHz 50MHz 7.5MHz, 10MHz, 20MHz 40MHz E1-shielded RJ48, 120Ω E1-HDB3 Up to 4 or 8E1 4 / 8E1 14MHz, 28MHz, 56MHz 7MHz, 14MHz, 28MHz 7MHz, 14MHz 13.75MHz, 27.5MHz, 55MHz 7MHz, 13.75MHz, 27.5MHz 13.75MHz Additional LAN Specifications Available throughput at 100Mbs full duplex data input rates. With flow control (Channel spacing @ FEC10) LAN sensitivity @ FER (Frame error rate) LED Indicators ETSI PIN-52042 Ethernet only Ethernet+4E1 14 MHz – 18 Mbps 14 MHz – 10 Mbps 28 MHz – 36 Mbps 28 MHz – 28 Mbps 56 MHz – 48 Mbps 56 MHz – 40 Mbps FCC PIN-42042 Ethernet only Ethernet+4DS1 12.5 MHz – 12 Mbps 12.5 MHz – 6 Mbps 25 MHz – 24 Mbps 25 MHz – 18 Mbps 50 MHz – 48 Mbps 50 MHz – 42 Mbps *Note: Each E1 used drops 2Mb/s from the maximum available Ethernet throughput* Frame error rate < 5x10-4 at channel spacing 14/28/56 MHz According to FER/BER equivalence table: ETSI EN 301 785 (Sensitivity @10-6 BER values are specified in tables I and II) Full / Half duplex, Port enabled / disabled, Port activity, speed and collisions WitLink-2000 Technical Specifications Rev-02 1+1 Redundancy Kits for 1 and 2 Antenna Configuration WitLink-2000® supports Hot Standby redundancy, with no single points of failure. Redundancy is achieved by routing the tributaries and interfaces input lines via a passive Redundant Switching Unit (RSU). The switching logic is performed in the RSU. Switching decisions are made according to Hardware and Software failure indications (link status, RSL, BER, etc.) generated by each terminal. A defective IDU or ODU can be easily removed Without affecting the operating link and replaced with no down time. The RSU is backup powered by either IDU. The RDK (Redundancy Kit) is used to complete a protected WitLink-2000® terminal. The RDK-X2161-C-13-38-1ANT kit supports one antenna configuration, for all frequencies, with asymmetric split RF Coupler. The kit includes the RSU, Redundant Plug-in (RPI-X2161, E3+16E1 or DS3+16DS1) and the upper and lower interconnection assemblies used to interconnect the RSU with the two IDUs. The kit includes the ODU Protection Assembly (OPA), which includes the ODU-1+1 Mount, one RF directional coupler and one rigid waveguide. Not included (per terminal side) are the 2 IDUs and 2 Plug-ins, 2 ODUs, 1 Antenna + mount, 2 coaxial cables and one flexible waveguide used to interconnect between the OPA and the selected antenna. The RDK-X2161-2ANT kit supports two antenna configurations for all frequencies. The kit includes the RSU, Redundant Plug-in (RPI-X2161, E3+16E1 or DS3+16DS1) and the Upper and Lower interconnection assemblies used to interconnect the RSU with the two IDUs. Each of the two ODUs are individually connected to an antenna. It is possible to mount the ODUs directly to the antennas, or use a flexible waveguide (Requires Mount-1+0 to mount the ODU on the pole). Not included (per terminal side) are the 2 IDUs and 2 Plug-ins, 2 ODUs, 2 Antennas + mounts, and 2 coaxial cables. Common Redundancy Kit Specification System characteristics RDK-X2161-C-13-38-1ANT RDK-X2161-2ANT Link Management IDU LCD Front-panel, RSU front panel, WitView-EM Management connections 10 Base-T Ethernet, SLIP (RJ45 connectors type) Switching time 100mSec typical Dual ODU/Single antenna Dual ODU/Dual antennas Mechanical configuration Mounted on Witcom’s antennas or ODUs Mounted on OPA on mount-1+0 and flexible waveguide FCC & ETSI, all frequencies, RF coupler Asymmetric split 1.8dB main, N/A 6.5dB standby Operation modes Hot standby Hot standby, frequency diversity WitLink-2000 Technical Specifications Rev-02 WitView-EM: SNMP Element Manager WitView-EM™ is an intuitive, pro-active element network management system with enhanced diagnostic and performance monitoring tools. It provides open, reliable and user-friendly GUI-based SNMP management. Based on a standard SNMP platform, WitView-EM™ can be integrated with HP OpenView™ or used as a stand-alone management application. WitView-EM™ supports local and remote terminal configuration, status/alarm reporting, traps, statistics (per G.826) and diagnostics. WitView-EM™ provides the SNMP tool to proactively manage all links from a single operator console, over IP. WitView-EM™ runs on Microsoft Windows® 95/98/2000 or NT stations. The embedded SNMP agent in each WitLink-2000® IDU implements standard IEFT/RFC MIB II Ethernet, E1/DS1, E3/DS3 MIBs, and private WitLink-2000® MIB extensions that enable remote monitoring and control of the entire link or complete network from a single point. An incorporated RIP Protocol enables simultaneous management of all radio links. All radio links can be easily in-band or out-of-band controlled from the management station. All system parameters are software configurable. Trivial File Transfer Protocol (TFTP) enables remote software upgrading. WitLink-2000 Technical Specifications Rev-02