Vector V36S SPECIFIERS GUIDE Overview Vector V36S Key Features ≤ 3447lm/m 1050lm/ft ≤ 40w/m 12w/ft Vector® V36S linear LED profile, just 36mm wide. V36S is ideal for interior surface mounted installation. Incorporating an all-new OPX diffuser in seamless edge-to-edge design, this unique diffuser is tuned specifically to provide consistent linear optical diffusion without any imaging of individual LEDs. Available in power ratings from 7W per metre to 40W per metre and CCTs of 2600K, 2900K, 3300K, 3800K, 5000K along with static colours and RGB options. High output and the ability to combine up to three LED colour temperatures sideby-side makes V36S our most versatile product yet. ≤ 87lm/w ≤ 88 CRI 2600 - 5000K CCT CLICK-CONNECT PowerTHRU 24VDC CV IPX0 White Spectrum™ technology built-in with Opal OPX™ diffuser options. Joinable pieces made in 100mm increments up to 2000mm with ‘invisible’ stealth mounts. Vector V36S Applications V36S is ideally suited to interior surface mounted linear applications. Vector V36S Performance Performance Table 40W /m CCT V36S-40 lumens1 /m lumens1 /w watts2 /m CRI R9 2670 - 2870K 2376 60 39.6 81 +31 2600K 2556 65 39.6 88 +56 2900K 3141 79 39.6 60 -49 3300K 2997 75 39.6 81 +30 3800K 3447 87 39.6 69 -17 5000K 3360 86 39.6 65 -53 PRE-PRODUCTION ESTIMATES 1 Maximum total LED lumens per metre excluding LOR factor. 2 Power rated at 24vdc. Data @25°C Ta V36S-26 Performance Table 26W /m CCT lumens1 /m lumens1 /w watts2 /m CRI R9 2670 - 2870K 1584 60 26.4 81 +31 2600K 1704 65 26.4 88 +56 2900K 2094 79 26.4 60 -49 3300K 1998 75 26.4 81 +30 3800K 2298 87 26.4 69 -17 5000K 2240 86 26.4 65 -53 PRE-PRODUCTION ESTIMATES 1 Maximum total LED lumens per metre excluding LOR factor. 2 Power rated at 24vdc. Data @25°C Ta Light output ratio 0.55 LOR 110º beam angle PRE-PRODUCTION ESTIMATES Vector V36S Performance Performance Table 13W /m CCT V36S-13 lumens1 /m lumens1 /w watts2 /m CRI R9 2670 - 2870K 792 60 13.2 81 +31 2600K 852 65 13.2 88 +56 2900K 1047 79 13.2 60 -49 3300K 999 75 13.2 81 +30 3800K 1149 87 13.2 69 -17 5000K 1120 86 13.2 65 -53 PRE-PRODUCTION ESTIMATES 1 Maximum total LED lumens per metre excluding LOR factor. 2 Power rated at 24vdc. Data @25°C Ta V36S-07 Performance Table 7W /m CCT lumens1 /m lumens1 /w watts2 /m CRI R9 2670 - 2870K 356 52 6.9 80 +31 2600K 472 68 7.0 88 +61 2900K 569 79 7.2 60 -49 3300K 588 83 7.0 67 -23 3800K 634 88 7.2 69 -17 5000K 680 97 7.0 63 -73 PRE-PRODUCTION ESTIMATES 1 Maximum total LED lumens per metre excluding LOR factor. 2 Power rated at 24vdc. Data @25°C Ta LED 3-Chip 5450 SMT package V10-40: 3 x 16.7mm pitch V10-13: 1 x 16.7mm pitch Vector V36S V10-26: 2 x 16.7mm pitch V10-07: 1 x 25.0mm pitch Dimensions 2.5 XX00* ~100 42 36 2.5 100mm 200mm 300mm 400mm 500mm 600mm 700mm 800mm 900mm 1000mm 1100mm 1200mm 1300mm 1400mm 1500mm 1600mm 1700mm 1800mm 1900mm 2000mm ~100 ~1.4kg per metre 50 Standard lengths* 50 *At each end of a continuous line allow +2.5mm for end-cap. i.e. total length +(2x2.5)5mm. SIDE TOP Vector V36S Options & Accessories Continuous Lines V36S-JA203-R1 Linear Joiner V36S-MB202-R1 End Cap Pair (adds 2x2.5mm) Example: 2000mm 2000mm 4005mm Linear Joiner End Cap (+2.5mm) End Cap (+2.5mm) Mounting 7 V36S-MS501-R1 Stealth Mount Click-Connect Cable Extender VECA-CA025-R1 250mm (male + female) VECA-CA100-R1 1000mm (male + female) Vector V36S 31 Drivers & Dimming Wiring V36S-07/13 can be installed in power-through configuration lengths up to 6 metres subject to maximum cable size and length, V36S-26 is up to 3 meters and V36S-40 up to 2 metres Longer lengths can easily be achieved by running a parallel feed as shown in the 9m example below. Use only with maximum output 24 VDC voltage Class 2 power unit. 6m example 80W 24VDC 1.5m 1.5m 1.5m 1.5m 1.5m 1.5m 9m example 1.5m 1.5m 1.5m 1.5m 120W 24VDC Voltage V36S is rated to operate at 24VDC constant voltage. Its full operating range is 19.3 to 25.6 VDC. Start-voltage is defined as the voltage measured at the furthest cable point away from the driver. When calculating maximum cable size and length limits, installers must make their own checks to ensure that the minimum start voltage is correct as shown in the table below. V36S-40/26/13/07 min. start voltage V36S-40/26/13/07 Loading V36S Length min. start voltage V36S Length V36-40 A V36-26 A V36-13 A V36-07 A > 1m > 2m > 3m > 4m > 5m > 6m 20.3 VDC 20.6 VDC 21.1 VDC 21.8 VDC 22.8 VDC 23.9 VDC >1m >2m >3m >4m >5m >6m 1.65 3.30 4.95 6.60 8.25 9.90 1.10 2.20 3.30 4.40 5.50 6.60 0.55 1.10 1.65 2.20 2.75 3.30 0.30 0.60 0.90 1.20 1.50 1.80 24VDC Minimum start-voltage check point Vector V36S 1-10V / DALI / DMX V36S is ideally suited to dimming (via a PWM interface) with a 1-10V, DALI or DMX control signal. Maximum cable size and distance should be adjusted if using a dimming interface as shown in the wiring example tables. Typical PWM interfaces can handle 5A allowing a maximum of 9m of V36S-13 or 16m of V36S-07 per interface. Dimming Control 24VDC Interface max. 2m Drivers Drivers must be of constant voltage type providing 24VDC power supply. Recommended minimum driver ratings are shown in the table above. It is recommended that only drivers with overload and short-circuit protection are used. Use only with maximum output 24 VDC voltage Class 2 power unit. Recommended minimum driver rating V36S Length* V36-40 A Driver VA V36-26 A Driver VA V36-13 A Driver VA V36-07 A Driver VA >4m >6m >9m >12m >16m 6.6A 9.9A 15.0A 19.8A 26.4A 180W 240W 360W 480W 660W 4.4A 6.6A 10.0A 13.2A 17.6A 120W 160W 240W 320W 440W 2.2A 3.3A 5.0A 6.6A 8.8A 60W 80W 120W 160W 220W 1.2A 1.8A 2.7A 3.6A 4.8A 30W 45W 65W 90W 120W *Parallel wiring where applicable. Installation Notes 24VDC power supplies and dimming interfaces are often tested and verified to be EMI compliant with secondary cable lengths of up to 10m (shorter lengths on some devices). For cable lengths exceeding 10m, EMI emissions should be verified in the application. When EMI emissions exceed the allowed levels it may be possible to reduce them by using ferrite cores (not supplied). 24VDC cables should be shielded if longer than 10m total length. Recommended maximum cable lengths for dimmed circuits are based on a typical dimming interface voltage drop of 0.3V. Installers should check the specific voltage drop of the interface they are using and adjust cable length accordingly. *Recommended cable lengths shown are based on average resistance for typical copper solid core cables. Cable characteristics may vary acording to manufacturer, temperature, copper purity, connections etc. Installers must make their own checks to ensure that the minimum start voltage is correct. The start-voltage check point is located at the furthest cable point from the driver. Vector V36S Wiring Examples V36S-13 Switched 40W 24VDC 1500mm 81m max. [1.5mm²] 80W 24VDC 1500mm ~3m max. 2000mm 2000mm 3m max. [2.5mm²] 2000mm ~6m max. Cable size & maximum cable distance* V36S Length 0.5mm² 20AWG 0.75mm² 18AWG 1.0mm² 17AWG 1.5mm² 15AWG 2.5mm² 13AWG >1m >2m >3m >4m >5m >6m 100m 48m 27m 15m 7m 1m 150m 72m 40m 22m 10m 1m 200m 96m 54m 30m 14m 1m 300m 144m 81m 45m 21m 2m 500m 240m 135m 75m 35m 3m V36S-13 Dimmed Dimming Control 40W 24VDC 1500mm Interface 72m max. [1.5mm²] 1500mm ~3m max. Dimming Control 80W 24VDC Interface 2000mm 2000mm 2m max. [2.5mm²] 2000mm ~6m max. Cable size & maximum cable distance* V36S Length 0.5mm² 20AWG 0.75mm² 18AWG 1.0mm² 17AWG 1.5mm² 15AWG 2.5mm² 13AWG >1m >2m >3m >4m >5m >6m 92m 42m 24m 13m 5m - 138m 63m 36m 19m 7m 1m 184m 84m 48m 26m 10m 1m 276m 126m 72m 38m 14m 1m 460m 210m 120m 64m 24m 2m Vector V36S V36S-07 Switched 25W 24VDC 1500mm 144m max. [1.5mm²] 60W 24VDC 1500mm ~3m max. 2000mm 2000mm 4m max. [2.5mm²] 2000mm ~6m max. Cable size & maximum cable distance* V36S Length 0.5mm² 20AWG 0.75mm² 18AWG 1.0mm² 17AWG 1.5mm² 15AWG 2.5mm² 13AWG >1m >2m >3m >4m >5m >6m 180m 86m 48m 28m 12m 1m 270m 129m 72m 41m 18m 1m 360m 172m 96m 55m 24m 2m 540m 258m 144m 83m 36m 2m 900m 430m 240m 138m 60m 4m V36S-07 Dimmed Dimming Control 25W 24VDC 1500mm Interface 84m max. [1.5mm²] 1500mm ~3m max. Dimming Control 60W 24VDC Interface 2000mm 2000mm 3m max. [2.5mm²] 2000mm ~6m max. Cable size & maximum cable distance* Vector V36S V36S Length 0.5mm² 20AWG 0.75mm² 18AWG 1.0mm² 17AWG 1.5mm² 15AWG 2.5mm² 13AWG >1m >2m >3m >4m >5m >6m 168m 76m 42m 23m 8m 1m 252m 114m 63m 35m 13m 1m 336m 152m 84m 46m 17m 1m 504m 228m 126m 69m 25m 2m 840m 380m 210m 115m 42m 3m LED Specification White Spectrum™ LED Vector LEDs with White Spectrum™ technology benefit from ultra-fine LED x,y bining coordinates to precise specifications. Testing and control of these specifications gives very accurate control of correlated colour temperatures (CCT). White Spectrum™ technology also allows us to offer our high colour rendering index rating of 88 CRI (Ra) as standard for 2600K products. Each 2600K Vector LED is ultra-fine binned from a defined x, y range bin area covering approximately 2 MacAdam steps. This is far smaller than the ANSI C78.377A Standard which equates to 7 MacAdam steps. This binning accuracy equates to a colour temperature precision of less than 2.0% tolerance giving approximately +/- 50K. White Spectrum™ is one of the leading global LED technologies. A typical warm white fine-bin from another manufacturer is typically at least 40% larger than Lumino’s White Spectrum™ ultra-fine binning. VECTOR 2600K 2-step MacAdam 0.43 ANSI C78.377A 2700K 7-step MacAdam 0.39 0.41 0.43 26 280 00 K 0K 0.41 0.45 0.47 0.49 eQ™ LED To compliment Lumino’s White Spectrum ultra-fine bining, eQ™ offers wider binning within defined tolerances. eQ™ gives specifiers more choice and provides an economical solution where ultra-fine bining is not essential for a project. Available in 2670-2870K and 3020-3220K, eQ™. Vector V36S Specification Codes Code Configuration V36S can be custom configured to suit the exact requirements of your project. Length, CCT, power, wires and connector type can all be specified as shown below. V 3 6 S-B D D 2 0 0 0 -D 1 C E B LED CCT C D F G H B E FINISH D SILVER ANOD. E WHITE RAL9003 F BLACK RAL9005 LENGTH XX00 MM Vector V36S 2600K WS 2900K WS 3300K WS 3800K WS 5000K WS 2670-2870K EQ 3020-3220K EQ LED POWER 1G 1C 2C 3C 07 WM 13 WM 26 WM 40 WM Technology Material specifications T6 6063 Aluminium extrusion Extruded polycarbonate OPX diffusser PCB electroplated copper foil on FR4 substrate 22AWG wires stranded copper / PVC Operating environment Running Temperature (Tc): Ambient Temperature (Ta): Storage Temperature: Ingress Protection rating: Ave. 17°C above Ta -40 to +60°C -40 to +100°C IPX0 IPX0 Certification Standards IEC 60598-2-4:1997 Luminairesused in conjuction with IEC 60598-1:2008 IEC 62031:2008 LED Modules for general lighting EN55015: 2006+A1 :2007 EN61547: 1995+A1 :2000 Following the provisions of EMC Directive 2004/108/EC CB Testing Laboratory: Intertek Product Safety Laboratory (UK) Vector V36S The information in this document is subject to change without notice Check for latest specifications at www.lumino.co.uk Copyright © 2014 Lumino Limited E&OE Vector V36S Vector V36S Lumino Limited Lumino House, Lovet Road Harlow, Essex CM19 5TB United Kingdom T +44 (0) 1279 635411 E info@lumino.co.uk www.lumino.co.uk SG-V36S-WHI-R1404