Version
06.00
¸FSP Spectrum Analyzer
Data Sheet
May
2008
Specifications
Specifications are valid under the following conditions:
15 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to, and total calibration performed.
Data without tolerances: typical values only.
Data designated "nominal" applies to design parameters and is not tested.
Data designated "σ = xx dB" is shown as standard deviation.
¸FSP3
¸FSP7
¸FSP13
¸FSP30
¸FSP40
9 kHz to 3 GHz
9 kHz to 7 GHz
9 kHz to 13.6 GHz
9 kHz to 30 GHz
9 kHz to 40 GHz
Frequency
Frequency range
Frequency resolution
0.01 Hz
Internal reference frequency (nominal)
Aging per year1)
1 × 10 –6
Temperature drift
1 × 10–6
With option ¸FSP-B4 (OCXO)
Aging per year1)
1 × 10–7
Temperature drift
1 × 10–8
External reference frequency
10 MHz
Frequency display
with marker or frequency counter
Marker resolution
Max. deviation
(sweep time >3 × auto sweep time)
span/500
±(frequency × reference frequency + 0.5% × span + 10% × resolution bandwidth + ½ (last digit))
Frequency counter resolution
0.1 Hz to 10 kHz (selectable)
Count accuracy (S/N >25 dB)
±(frequency × reference frequency + ½ (last digit))
Frequency span
Max. span deviation
0 Hz,
10 Hz to 3 GHz
0 Hz,
10 Hz to 7 GHz
0 Hz,
10 Hz to 13.6 GHz
0.1%
Spectral purity (dBc (1 Hz)) SSB phase noise, f = 500 MHz, for f > 500 MHz see diagrams below
Carrier offset
100 Hz
<–84, typ.–90
1 kHz
<−100, typ.−108
10 kHz
<−106, typ. −113
100 kHz2)
<−110, typ. −113
1 MHz2)
<−120, typ.−125
10 MHz
typ.−145
Residual FM
f = 500 MHz, RBW 1 kHz,
sweep time 100 ms
1)
2)
2
After 30 days of operation.
Valid for span >100 kHz.
¸FSP Spectrum Analyzer
typ. 3 Hz
0 Hz,
10 Hz to 30 GHz
0 Hz,
10 Hz to 40 GHz
Typical values for SSB phase noise (reference to 1 Hz bandwidth):
Offset
fin = 3 GHz
fin = 7 GHz
fin = 13 GHz
fin = 22 GHz
fin = 26 GHz
fin = 40 GHz
100 Hz
−74 dBc
−67 dBc
−61 dBc
−57 dBc
−55 dBc
−52 dBc
1 kHz
−100 dBc
−94 dBc
−88 dBc
−84 dBc
−82 dBc
−79 dBc
10 kHz
−108 dBc
−104 dBc
−98 dBc
−94 dBc
−92 dBc
−91 dBc
100 kHz
−108 dBc
−106 dBc
−100 dBc
−96 dBc
−94 dBc
−92 dBc
1 MHz
−118 dBc
−118 dBc
−112 dBc
−108 dBc
−106 dBc
−102 dBc
Typ. SSB phase noise vs offset
–60
fin in GHz
SSB phase noise in dBc (1 Hz)
–70
0.5
3
7
13
22
30
40
–80
–90
–100
–110
–120
–130
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
Offset frequency
Typ. SSB phase noise vs frequency
–50
Offset frequency
100 Hz
1 kHz
10 kHz
100 kHz
1 MHz
SSB phase noise in dBc (1 Hz)
–60
–70
–80
–90
–100
–110
–120
–130
0
5
10
15
20
Frequency in GHz
25
30
40
¸FSP Spectrum Analyzer
3
¸FSP3
¸FSP7
¸FSP13
¸FSP30
¸FSP40
Sweep time
Span ≥10 Hz
2.5 ms to 16000 s
Max. deviation
1%
Span 0 Hz
1 μs to 16000 s
Resolution
125 ns
Resolution bandwidths
Bandwidths
10 Hz to 10 MHz (–3 dB) in 1, 3 sequence
EMI bandwidths
200 Hz, 9 kHz, 120 kHz (–6 dB)
Bandwidth accuracy
≤100 kHz
<3%
300 kHz to 3 MHz
<10%
10 MHz
+10%, –30%
Shape factor –60 dB: –3 dB
≤100 kHz
<5:1 (Gaussian filters)
<15:1 (4-pole synchronously tuned filters)
300 kHz to 3 MHz
<7:1
10 MHz
Shape factor –60 dB: –6 dB
EMI bandwidths
<5:1
Video bandwidths
1 Hz to 10 MHz in 1, 3 sequence
FFT filter
Bandwidths
1 Hz to 30 kHz (–3 dB) in 1, 3 sequence
Bandwidth accuracy
5%, nominal
Shape factor –60 dB:–3 dB
2.5:1 nominal
Channel filter
Bandwidths
100; 200; 300; 500 Hz;
1; 1.5; 2; 2.4; 2.7; 3; 3.4; 4; 4.5; 5; 6; 8.5; 9; 10; 12.5; 14; 15; 16; 18 (RRC); 20; 21; 24.3 (RRC); 25; 30; 50; 100;
150; 192; 200; 300; 500 kHz; 1;
1.228; 1.5; 2; 3; 5 MHz
1.28 (RRC), 3.84 (RRC), 4.096 (RRC)
Level
Display range
displayed average noise level to 30 dBm
Maximum input level
DC voltage
50 V
0V
DC voltage with ¸FSP-B29
0V
RF attenuation 0 dB
CW RF power
20 dBm
Pulse spectral density
97 dBμV (1 MHz)
RF attenuation ≥10 dB
CW RF power
30 dBm
Max. pulse voltage
150 V
50 V
Max. pulse energy (10 μs)
1 mWs
0.5 mWs
1 dB compression of input mixer
0 dB RF attenuation, f > 200 MHz
0 dBm nominal
Intermodulation
3rd-order intermodulation
Intermodulation-free dynamic range, level 2 × –30 dBm, Δf > 5 × RBW or 10 kHz, whichever is larger
>70 dBc, TOI >5 dBm
20 MHz to 200 MHz
>74 dBc, TOI >7 dBm (typ. 10 dBm)
200 MHz to 3 GHz
3 GHz to 7 GHz
−
7 GHz to 13.6 GHz
−
−
>80 dBc, TOI >10 dBm (typ. 15 dBm)
13.6 GHz to 30 GHz
−
−
−
30 GHz to 40 GHz
−
−
−
>80 dBc, TOI >10 dBm
>76 dBc, TOI >8 dBm >80 dBc, TOI >10 dBm
−
With optional Electronic Attenuator ¸FSP-B25 switched on
20 MHz to 200 MHz
>74 dBc, TOI > 7 dBm
−
200 MHz to 3 GHz
>80 dBc, TOI > 10 dBm
−
3 GHz to 7 GHz
>84 dBc, TOI > 12 dBm
−
4
¸FSP Spectrum Analyzer
>80 dBc, TOI >10 dBm
¸FSP3
¸FSP7
¸FSP13
¸FSP30
¸FSP40
Second harmonic intercept point (SHI)
<100 MHz
typ. 25 dBm
100 MHz to 1.5 GHz
typ. 35 dBm
1.5 GHz to 7 GHz
−
7 GHz to 13.6 GHz
−
−
13.6 GHz to 30 GHz
−
−
−
30 GHz to 40 GHz
−
−
−
typ. 80 dBm
typ. 80 dBm
typ. 80 dBm
−
typ. 80 dBm
Displayed average noise level
(0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω)
Frequency
9 kHz
<−95 dBm
100 kHz
<−100 dBm
<−120 dBm, typ. −125 dBm
1 MHz
10 MHz to 1 GHz
<−142 dBm,
typ. −145 dBm
<−140 dBm, typ. −145 dBm
1 GHz to 3 GHz
<−140 dBm,
typ. −145 dBm
<−138 dBm, typ. −143 dBm
3 GHz to 7 GHz
−
<−138 dBm,
typ. −143 dBm
7 GHz to 13.6 GHz
−
−
13.6 GHz to 22 GHz
−
−
−
<−120 dBm,
typ. −128 dBm
−
22 GHz to 30 GHz
−
−
−
<−115 dBm,
typ. −123 dBm
−
13.6 GHz to 20 GHz
−
−
−
−
<−120 dBm,
typ. −128 dBm
20 GHz to 30 GHz
−
−
−
−
<−120 dBm,
typ. −128 dBm
30 GHz to 40 GHz
−
−
−
−
<−112 dBm,
typ. −120 dBm
<−135 dBm, typ. −140 dBm
<−132 dBm, typ. −138 dBm
Displayed average noise level with preamplifier on (option ¸FSP-B25)
10 MHz to 2 GHz
<–152 dBm
−
2 GHz to 7 GHz
<–150 dBm
−
Immunity to interference
Image frequency
>70 dB
Intermediate frequency (f <3 GHz)
>70 dB
Spurious responses (f >1 MHz, without
input signal, 0 dB attenuation)
<−103 dBm
Other spurious (with input signal, mixer
level <–10 dBm, Δf >100 kHz)
f <7 GHz: <−70 dBc
f <13.6 GHz: <−64 dBc
f <30 GHz: <−56 dBc
Level display
Screen
Logarithmic level scale
Linear level scale
Traces
Trace detector
Trace functions
Number of test points
501 × 400 pixels (one diagram), max. two diagrams with independent settings
10 dB to 200 dB, in steps of 10 dB
10% of reference level per level division (10 divisions)
max. 3, with two diagrams on screen max. 3 per diagram
max peak, min peak, auto peak, sample, quasi-peak, average, RMS
clear/write, max. hold, min hold, average
501, selectable in steps of approx. factor 2, 125 to 8001
Setting range of reference level
Logarithmic level display
–130 dBm to 30 dBm, in steps of 0.1 dB
Linear level display
70.71 nV to 7.07 V in steps of 1%
Units of level scale
dBm, dBmV, dBμV, dBμA, dBpW (log level display), mV, μV, mA, μA, pW, nW (linear level display)
Max. uncertainty of level measurement
At 128 MHz, −30 dBm (RF attenuation
10 dB, RBW 10 kHz, ref. level –20 dBm)
<0.2 dB (σ = 0.07 dB)
¸FSP Spectrum Analyzer
5
¸FSP3
¸FSP7
¸FSP13
¸FSP30
¸FSP40
Frequency response
<50 kHz
<+0.5/− 1.0 dB
<0.5 dB (σ = 0.17 dB)
50 kHz to 3 GHz
<2 dB (σ = 0.7 dB)
3 GHz to 7 GHz
–
7 GHz to 13.6 GHz
–
–
13.6 GHz to 30 GHz
–
–
–
30 GHz to 40 GHz
–
–
–
<2.5 dB1)
<3 dB1)
<4 dB1)
–
Frequency response with option ¸FSP-B25 switched on (preamplifier, electronic attenuator)
<1 dB (σ = 0.33 dB)
10 MHz to 3 GHz
3 GHz to 7 GHz
–
–
<2 dB (σ = 0.7 dB)
–
Attenuator
<0.2 dB (σ = 0.07 dB)
Reference level switching
<0.2 dB (σ = 0.07 dB)
Display nonlinearity LOG/LIN (S/N >16 dB)
RBW ≤100 kHz
0 dB to –70 dB
<0.2 dB (σ = 0.07 dB)
–70 dB to –90 dB
<0.5 dB (σ = 0.17 dB)
RBW ≥300 kHz
0 dB to –50 dB
<0.2 dB (σ = 0.07 dB)
–50 dB to –70 dB
<0.5 dB (σ = 0.17 dB)
Bandwidth switching uncertainty (ref. to RBW = 10 kHz)
10 Hz to 100 kHz
<0.1 dB (σ = 0.03 dB)
300 kHz to 10 MHz
<0.2 dB (σ = 0.07 dB)
1 Hz to 3 kHz, FFT
<0.2 dB (σ = 0.03 dB)
Total measurement uncertainty
0.5 dB
50 kHz to 3 GHz, signal level 0 dB to
70 dB below reference level,
S/N >16 dB,
RBW ≤ 100 kHz, 95 % confidence level
Trigger functions
Trigger
Span ≥10 Hz
Trigger source
free run, video, external, IF level
Trigger offset
125 ns to 100 s, resolution 125 ns min. (or 1% of offset)
Span = 0 Hz
Trigger source
free run, video, external, IF level
Trigger offset
±125 ns to 100 s, min. resolution 125 ns, dependent on sweep time
Max. deviation of trigger offset
±(125 ns + (0.1% × delay time))
Gated sweep
Trigger source
external, IF level, video
Gate delay
1 μs to 100 s
Gate length
125 ns to 100 s, min. resolution 125 ns or 1% of gate length
Max. deviation of gate length
±(125 ns + (0.05% × gate length))
Inputs and outputs (front panel)
N female, 50 Ω
RF input
test port system 50 Ω, test port system 50 Ω,
N female,
N female,
3.5 mm female2)
K female2)
VSWR (RF attenuation >0 dB)
f <3 GHz
1.5:1
f <7 GHz
−
f <13 GHz
−
−
f <30 GHz
−
−
−
f <40 GHz
−
−
−
2.0:1
Input attenuator
With option ¸FSP-B25
2.5:1
3.0:1
−
0 dB to 70 dB in 10 dB steps
0 dB to 75 dB in 5 dB steps
not available
Probe power supply
+15 V DC, –12.6 V DC and ground, max. 150 mA
Keyboard connector
PS/2 female for MF2 keyboard
AF output (only with option ¸FSP-B3)
6
¸FSP Spectrum Analyzer
3.5 mm mini-jack
3.0:1
¸FSP3
¸FSP7
¸FSP13
Output impedance
10 Ω
Open-circuit voltage
up to 1.5 V, adjustable
¸FSP30
¸FSP40
Inputs and outputs (rear panel)
Zout = 50 Ω, BNC female
IF 20.4 MHz
Level
RBW ≤30 kHz, FFT
–10 dBm at reference level, mixer level >–60 dBm
RBW ≥100 kHz
0 dBm at reference level, mixer level >–60 dBm
Reference frequency
Output
BNC female
Output frequency
10 MHz
Level
0 dBm, nominal
Input
10 MHz
0 dBm into 50 Ω
Required level
Others
Power supply for noise source
BNC female, 0 V and 28 V, switchable, max. 100 mA
BNC female, >10 kΩ
External trigger/gate input
Trigger voltage
1.4 V (TTL)
IEC/IEEE bus remote control interface to IEC 625-2 (IEEE 488.2)
Command set
SCPI 1997.0
Connector
24-pin Amphenol female
Interface functions
SH1, AH1, T6, L4, SR1, RL1, PP1, DC1, DT1, C0
Serial interface
RS-232-C (COM), 9-pin sub-D connector
Printer interface
parallel (Centronics-compatible)
Mouse connector
PS/2 female
Connector for ext. monitor (VGA)
15-pin sub-D connector
General data
Display
21 cm TFT colour display (8.4”)
Resolution
640 × 480 pixels (VGA resolution)
<2 × 10 –5
Pixel failure rate
Mass memory
1.44 MByte 3½” disk drive (built-in), hard disk
Data storage
>500 instrument settings and traces
Temperatures
Operating temperature range
+5°C to +40°C
Permissible temperature range
+5°C to +45°C
Storage temperature range
–40°C to +70°C
Damp heat
+40°C at 95% relative humidity (EN 60068-2-30)
Mechanical resistance
Vibration, sinusoidal
5 Hz to 150 Hz, max. 2 g at 55 Hz; 0.5 g from 55 Hz to 150 Hz; meets EN60068-2-6, EN60068-2-30, EN61010-1,
MIL-T-28800D, class 5
Vibration, random
10 Hz to 100 Hz, acceleration 1 g (rms)
Shock test
40 g shock spectrum, meets MIL-STD-810C and MIL-T-28800D, classes 3 and 5
Recommended calibration interval
2 years for operation with external reference,1 year with internal reference
Power supply
AC supply
Typical power consumption
100 V AC to 240 V AC, 50 Hz to 400 Hz, 3.1 A to 1.3 A, class of protection I to VDE411
70 VA
Safety
120 VA
RFI suppression
meets EMC Directive of EU (89/336/EEC) and German EMC law
Test mark
VDE, GS, CSA, CSA-NRTL/C
Dimensions in mm (W × H × D)
Weight
1)
2)
150 VA
meets EN61010-1, UL3111-1, CSAC22.2 No. 1010-1,
412 × 197 × 417
10.5 kg
11.3 kg
12 kg
RF attenuation 10 dB, sweep time >1s/1 GHz.
See recommended extras for alternate connectors.
¸FSP Spectrum Analyzer
7
Specifications of options
Tracking Generator ¸FSP-B9
Unless specified otherwise, specifications not valid for frequency range from –3 × RBW to +3 × RBW; however, at least not valid from –9 kHz to +9 kHz.
The specified level accuracy of the tracking generator is valid under the following conditions: RF attenuation ≥ 20 dB and sweep time ≥2000 ms.
Frequency
Frequency range
Frequency offset
Setting range
Resolution
Spectral purity (dBc (1 Hz)) SSB phase noise, f = 500 MHz, carrier offset 100 kHz
Normal mode
With FM modulation on
Level
Level setting range
Level setting range with AM
Max. deviation of output level, 128 MHz, 0 dBm
Frequency response
Output level 0 dBm, 100 kHz to 2 GHz
Output level 0 dBm to −25 dBm, 9 kHz to 3 GHz
Dynamic range
Attenuation, RBW = 1 kHz, f > 10 MHz
Spurious
Harmonics, output level –10 dBm
Nonharmonics, output level 0 dBm
9 kHz to 3 GHz
±150 MHz
1 Hz
typ. –90
typ. –70
–30 dBm to 0 dBm in steps of 0.1 dB
–30 dBm to –6 dBm in steps of 0.1 dB
<1 dB
<1 dB
<3 dB
typ. 110 dB
typ. –30 dBc
typ. –30 dBc
Modulation
Modulation format (external)
AM, f > 10 MHz
Modulation depth
Modulation frequency range
FM, f > 10 MHz
Frequency deviation
Modulation frequency range
I/Q modulation, f > 10 MHz
0 Hz to 30 MHz
Inputs and outputs (front panel)
RF output
VSWR
Inputs and outputs (rear panel)
TG/AM IN
TG Q/FM IN
I/Q, AM, FM, FM-DC, PM, ASK, FSK
0% to 99%
0 Hz to 1 MHz
0 Hz to 20 MHz
0 Hz to 100 kHz
typ. 1 dB
N female, 50 Ω
typ. 2:1
Vmax(pp) = 1 V; Zin = 50 Ω, BNC female
Vmax(pp) = 1 V; Zin = 50 Ω, BNC female
External Generator Control ¸FSP-B10
Supported signal generators
¸SME02/03/06, ¸SMG, ¸SMGL, ¸SMGU, ¸SMH, ¸SMHU,
¸SMIQ02B/02E/03B/03E/04B/06B
¸SML, ¸SMR20/27/30/40/60
¸SMP02/22/03/04,¸SMX, ¸SMY
¸SMT02/03/06
LAN Interface ¸FSP-B16
Connector (rear panel)
Supported protocols
RJ-45
10Base-T (IEEE standard 10 Mbit/s 802.3)
100Base-TX (IEEE standard 100 Mbit/s 802.3u)
Extended Environmental Specification ¸FSP-B20
Temperature range (noncondensing)
Operating temperature range
Permissible temperature range
Mechanical resistance
Vibration, random
8
¸FSP Spectrum Analyzer
0°C to +50°C
0°C to +55°C
10 Hz to 300 Hz, acceleration 1.9 g (rms)
LO/IF ports for external Mixers ¸FSP-B21 (¸FSP40 only)
LO level
Frequency range
Level
IF input
IF frequency
Full scale level
2 port mixer, LO output/IF input (front)
Level deviation
IF level –30 dBm, reference level –20 dBm, RBW 30 kHz,
LO output/IF input (front)
Full scale level
3 port mixer, IF input (front)
Level deviation
IF level –30 dBm, reference level –20 dBm, RBW 30 kHz, IF input (front)
Inputs and outputs (front)
LO output/IF input
IF input
7 GHz to 13.2 GHz
+15.5 dBm ±3 dB
404.4 MHz
–20 dBm
<1dB
–20 dBm
<1dB
SMA female, 50 Ω
SMA female, 50 Ω
Electronic Attenuator ¸FSP-B25 (only for ¸FSP3 and ¸FSP7)
Frequency
Frequency range
10 MHz to 7 GHz
Input attenuator range (mechanical)
0 dB to 75 dB in 5 dB steps
Electronic attenuation range
0 dB to 30 dB in 5 dB steps
Preamplifier
20 dB, switchable
Displayed average noise level with preamplifier on (0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω)
10 MHz to 2 GHz
<–152 dBm
2 GHz to 7 GHz
<–150 dBm
Intermodulation with electronic attenuator on
3rd-order intermodulation, intermodulation-free dynamic range, level 2 × –30 dBm, Δf >5 × RBW or 10 kHz, whichever is larger
20 MHz to 200 MHz
>74 dBc, TOI >7 dBm
200 MHz to 3 GHz
>80 dBc, TOI >10 dBm
3 GHz to 7 GHz
>84 dBc, TOI >12 dBm
Max. deviation of level measurement
128 MHz, –30 dBm (RF attenuation 10 dB, RBW 10 kHz,
<0.2 dB (σ = 0.07 dB)
ref. level –20 dBm), preamplifier on
Electronic attenuator
<0.2 dB (σ = 0.07 dB)
Frequency response with preamplifier, electronic attenuator
10 MHz to 3 GHz
<1.0 dB (σ = 0.33 dB)
3 GHz to 7 GHz
<2 dB (σ = 0.7 dB)
Trigger Port ¸FSP-B28
Output voltage
Trigger port connector
high ≤1.4 V
low ≥0.7 V
25-pin sub-D female
Frequency range extension 20 Hz ¸FSP-B29
Frequency range
Frequency response <9 kHz
Displayed average noise level
0 dB RF attenuation, RBW 10 Hz, VBW 1 Hz, 20 averages, trace average, span 0 Hz, termination 50 Ω
20 Hz
100 Hz
1 kHz
20 Hz to fmax
<1 dB
<–58 dBm
<–75 dBm
<–85 dBm
DC Power Supply ¸FSP-B30
Input voltage range
Output voltage
Current consumption (VDC = 12 V, ¸FSP without options, default settings)
¸FSP3
¸FSP30
Operating temperature range
Storage temperature range
Dimensions in mm (W × H × D)
Weight
10 V to 28 V DC
25 A to 12.5 A
120 V to 360 V DC/300 W
typ. 6 A
typ. 8 A
0°C to +50°C
–40°C to +70°C
145 × 154 × 65
0.6 kg
¸FSP Spectrum Analyzer
9
Battery Pack ¸FSP-B31/-B32
NiMH battery pack with built-in load control for all ¸FSP and ¸ESPI models with options ¸FSP-B1 and ¸FSP-B30
Input voltage of battery pack
10 V to 28 V DC
Input voltage power supply (battery charge)
24 V DC/max. 3 A
Output voltage
Battery operation
13.2 V DC/200 Wh
Bypass operation
10 V to 28 V DC/10 A
Typical operating times (¸FSP without options)
¸FSP3
2h
¸FSP30
1.5 h
Charging time
5 h at +25°C
Operating temperature range (discharging)
0°C to +50°C
Operating temperature range (charging)
+10°C to +40°C
Storage temperature range (<1 year)
–20°C to +35°C
Storage temperature range (<1 month)
–20°C to +55°C
Dimensions (W × H × D)
400 mm × 134 mm × 42 mm
Weight
3.7 kg
AC adapter (¸FSP-B31 only)
Input voltage range
Input frequency range
Input power
Output voltage
Output current
Operating temperature range
Storage temperature range
Dimensions (W × H × D)
Weight
100 V to 240 V AC ±10%
50 Hz to 60 Hz ±5%
140 VA
24 V
3A
0°C to +50°C
–20°C to +70°C
132 mm × 58 mm × 30 mm
0.3 kg
Ordering information
Order designation
Type
Order No.
Spectrum Analyzer, 9 kHz to 3 GHz
¸FSP3
1164.4391.03
Spectrum Analyzer, 9 kHz to 7 GHz
¸FSP7
1164.4391.07
Spectrum Analyzer, 9 kHz to 13.6 GHz
¸FSP13
1164.4391.13
Spectrum Analyzer, 9 kHz to 30 GHz
¸FSP30
1164.4391.30
Spectrum Analyzer, 9 kHz to 40 GHz
¸FSP40
1164.4391.40
Accessories supplied
Power cable, compact manual, CD-ROM with operating manual and service manual.
¸FSP30: test port adapter with 3.5 mm female (1021.0512.00) and N female (1021.0535.00) connector.
¸FSP40: test port adapter with K female (1036.4790.00) and N female (1036.4777.00) connector.
Options
Order designation
Type
Order No.
Retrofittable Remarks
Options
Delete Manuals
¸FSP-B0
1129.8394.02
Rugged Case, carrying handle (factory-fitted)
¸FSP-B1
1129.7998.02
no
AM/FM Audio Demodulator
¸FSP-B3
1129.6491.02
yes
OCXO Reference Frequency
¸FSP-B4
1129.6740.02
yes
TV Trigger/RF Power Trigger
¸FSP-B6
1129.859.4.02
yes
Internal Tracking Generator 9 kHz to 3 GHz, I/Q modulator, for all ¸FSP models ¸FSP-B9
1129.6991.02
yes
External Generator Control for all ¸FSP models
¸FSP-B10
1129.7246.03
yes
Pulse Calibrator for ¸FSP
¸FSP-B15
1155.1006.02
yes
LAN Interface 100BT for all ¸FSP models with Windows XP (1164.4391.xx)
¸FSP-B16
1129.8042.03
yes
10
¸FSP Spectrum Analyzer
not with ¸FSP-B15.
not with ¸FSP-B21.
not with ¸FSP-B3;
required for ¸FS-K72/-K73
Order designation
Type
Order No.
Removable Flash Disk
¸FSP-B18
1163.0892.03
Retrofittable Remarks
Second Flash Disk for ¸FSP-B18
¸FSP-B19
1163.1124.03
Extended Environmental Specification
¸FSP-B20
1155.1606.06
no
LO/IF Ports for External Mixers
¸FSP-B21
1155.1758.03
yes
Electronic Attenuator, 0 dB to 30 dB, 5 dB steps, integrated preamplifier for
¸FSP3 and ¸FSP7
¸FSP-B25
1129.7746.03
yes
Trigger Port for ¸FSP for indication of trigger conditions
¸FSP-B28
1162.9915.02
yes
Frequency Range Extension 20 Hz for ¸FSP3/7
¸FSP-B29
1163.0663.07
no
Frequency Range Extension 20 Hz for ¸FSP13/30
¸FSP-B29
1163.0663.30
no
Frequency Range Extension 20 Hz for ¸FSP40
¸FSP-B29
1163.0663.40
no
DC Power Supply for Spectrum Analyzers ¸FSP
¸FSP-B30
1155.1158.02
yes
Battery Pack for Spectrum Analyzers ¸FSP
¸FSP-B31
1155.1258.02
yes
¸FSP-B1 and
¸FSP-B30 required
Spare Battery Pack for Spectrum Analyzers ¸FSP
¸FSP-B32
1155.1506.02
yes
¸FSP-B31 required
Demodulation Hardware and Memory Extension
¸FSP-B70
1157.0559.02
yes
required for ¸FS-K72/
-K73; ¸FSP-B15 required
no
¸FSP-B18 required
not with ¸FSP-B6;
only for ¸FSP40
Software
GSM/EDGE Application Firmware, Mobile
¸FS-K5
1141.1496.02
AM/FM/ϕM Measurement Demodulator
¸FS-K7
1141.1796.02
Application Firmware for Bluetooth® Measurements
¸FS-K8
1157.2568.02
Power Sensor Measurements
¸FS-K9
1157.3006.02
supports ¸NRP-Z11/-Z21
with ¸NRP-Z4 USB connector
Application Firmware for Noise Figure and Gain Measurements
¸FS-K30
1300.6508.02
Preamplifier ¸FSP-B25
recommended
Application Firmware for Phase Noise Measurements
¸FS-K40
1161.8138.02
3GPP BTS/Node B FDD Application Firmware
¸FS-K72
1154.7000.02
¸FSP-B15 and -B70
required
3GPP UE FDD Application Firmware
¸FS-K73
1154.7252.02
¸FSP-B15 required,
¸FSP-B70 recommended
3GPP HSDPA BTS Application Firmware
¸FS-K74
1300.7156.02
¸FS-K72 required
3GPP TD-SCDMA BTS Application Firmware
¸FS-K76
1300.7291.02
3GPP TD-SCDMA UE Application Firmware
¸FS-K77
1300.8100.02
CDMA2000® (IS-95) 1xEV-DV BTS FDD Application Firmware
¸FS-K82
1157.2316.02
CDMA2000® 1xEV-DV MS Application Firmware
¸FS-K83
1157.2416.02
CDMA2000® 1xEV-DO BTS Application Firmware
¸FS-K84
1157.2851.02
CDMA2000®-1xEV-DO MS Application Firmware
¸FS-K85
1300.6689.02
WLAN 802.11a TX Measurements Application Firmware
¸FSP-K90
1300.6650.02
WiBro IEEE 802.16 OFDMA Measurements Application Firmware
¸FSP-K93
1308.5500.02
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Rohde&Schwarz is under license.
CDMA2000® is a registered trademark of the Telecommunications Industry Association (TIA -USA).
¸FSP Spectrum Analyzer
11
Related data sheets
Designation
Type
Headphones
Order No.
Title
0708.9010.00
TV Trigger/RF Power Trigger ¸FSP-B6
PD 0757.6433
Order No.
DC Block,10 kHz to 18 GHz (type N)
¸FSE-Z4
1084.7443.02
GSM/EDGE Application Firmware ¸FS-K5
PD 0757.6185
IEC/IEEE Bus Cable, 1 m
¸PCK
0292.2013.10
AM/FM/ϕM Measurement Demodulator ¸FS-K7
PD 0757.6685
IEC/IEEE Bus Cable, 2 m
¸PCK
0292.2013.20
Bluetooth Application Firmware ¸FS-K8
PD 0757.7730
1096.3248.00
Application Firmware for Noise Figure and Amplifier Measure- PD 0758.0839.32
ments R&S®FS-K30
19" Rack Adapter (not for ¸FSP-B1) ¸ZZA478
Soft Carrying Case, grey
¸ZZT473
1109.5048.00
Printed operating manual (German)
–
1093.4820.11
Printed operating manual (English)
–
1093.4820.12
Application Firmware for Phase Noise Measurements
¸FS-K40
Printed service manual (German)
–
1093.4820.81
WCDMA 3GPP Application Firmware ¸FS-K72/-K73/-K74
1093.4820.82
TD-SCDMA Test Application Firmware ¸FS-K76/-K77
PD 0758.0880.32
CDMA2000® Base Station Test Application Firmware
1xEV-DO Base Station Test Application Firmware
¸FS-K82/-K84
PD 0758.1712.32
Mobile Station Test Application Firmware
¸FS-K83/¸FS-K85
PD 0758.1729.32
WLAN Application Firmware ¸FSQ-K91/
¸FSP-K90
PD 0758.1435.12
¸FSx-K92/-K93 WiMAX Application Firmware
PD 5213.8550.32
Printed service manual (English)
–
Matching Pads, 75 Ω
L Section
¸RAM
0358.5414.02
Series Resistor, 25 Ω1)
¸RAZ
0358.5714.02
SWR Bridge, 5 MHz to 3 GHz
¸ZRB2
0373.9017.52
SWR Bridge, 40 kHz to 4 GHz
¸ZRC
1039.9492.52
High-Power Attenuators, 100 W
3/6/10/20/30 dB
¸RBU100
1073.8495.XX
(XX=03/06/10/20/30)
¸RBU50
1073.8695.XX
(XX=03/06/10/20/30)
High-Power Attenuators, 50 W
3/6/10/20/30 dB
For ¸FSP30
Test Port Adapter, 3.5 mm male
–
1021.0529.00
Test Port Adapter, N male
–
1021.0541.00
Microwave Measurement Cable and
Adapter Set
¸FS-Z15
1046.2002.02
For ¸FSP40
Test Port Adapter K male
–
1036.4802.00
Test Port Adapter N male
–
1036.4783.00
Test Port Adapter 2.4 mm female
¸FSE-Z5
1088.1627.02
Connectors
Probe power connector , 3-pin
1)
1065.9480.00
Taken into account in device function RF INPUT 75 Ω.
Product brochure see PD 0758.1206.12
and at www.rohde-schwarz.com
(search term: FSP)
Certified Quality System
Certified Environmental System
ISO 9001
ISO 14001
DQS REG. NO 1954 QM
DQS REG. NO 1954 UM
www.rohde-schwarz.com
Europe, Africa, Middle East +491805124242* or +4989412913774 customersupport@rohde-schwarz.com
North America 1-888-TEST-RSA (1-888-837-8772) customer.support@rsa.rohde-schwarz.com
Latin America +1-410-910-7988 customersupport.la@rohde-schwarz.com
Asia/Pacific +6565130488 customersupport.asia@rohde-schwarz.com
PD 0758.2631.32
PD 0757.7246
¸is a registered trademark of Rohde&Schwarz GmbH&Co. KG · Trade names are trademarks of the owners · Printed in Germany (as)
PD 0758.1206.22 · ¸FSP Spectrum Analyzer · Version 06.00 · May 2008 · Data without tolerance limits is not binding Subject to change *0.14€/min within German wireline network; rates may vary in other networks (wireline and mobile) and countries.
Recommended extras