Energy Efficiency Business Rebates
Product Catalog
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
LIST OF LIGHTING PRODUCTS
Product
Code
Product Description
Units
$/Units
Pages
Fixtures
Compact Fluorescent Fixtures
L-C41
Interior Compact Fluorescent Fixture < 244 Watts (400 Watts lamp basecase) Tier I
Fixture
$75.00
9-10
L-C51
Interior Compact Fluorescent Fixture < 360 Watts (400 Watts lamp basecase) Tier II
Fixture
$45.00
9-10
L-C31
Interior Compact Fluorescent Fixture < 192 Watts (176 - 399 Watts lamp basecase)
Fixture
$40.00
9-10
L-C21
Interior Compact Fluorescent Fixture < 128 Watts (101 - 175 Watts lamp basecase)
Fixture
$35.00
9-10
L-C11*
Interior Compact Fluorescent Fixture < 70 Watts ( < 100 Watts lamp basecase)
Fixture
$20.00
9-10
L-C61
Exterior Compact Fluorescent Fixture < 70 Watts (< 100 Watts lamp basecase)
Fixture
$17.00
9-10
Interior Induction Fixtures
L-D41
Interior Induction Fixtures < 250 Watt (400 Watt lamp basecase) Tier I
Fixture
$125.00
10
L-D51
Interior Induction Fixtures < 360 Watt (400 Watt lamp basecase) Tier II
Fixture
$60.00
10
L-D31
Interior Induction Fixtures < 180 Watt (176 - 399 Watt lamp basecase)
Fixture
$75.00
10
L-D21
Interior Induction Fixtures < 120 Watt (101- 175 Watt lamp basecase)
Fixture
$60.00
10
L-D11
Interior Induction Fixtures < 70 Watts (< 100 Watts lamp basecase)
Fixture
$35.00
10
Exterior Induction Fixtures
L-D01
Exterior Induction Fixtures < 250 Watt (400 Watt lamp basecase)
Fixture
$100.00
10-11
L-D91
Exterior Induction Fixtures < 180 Watt (201- 399 Watt lamp basecase)
Fixture
$50.00
10-11
L-D81
Exterior Induction Fixtures < 120 Watt (176 - 200 Watt lamp basecase)
Fixture
$50.00
10-11
L-D71
Exterior Induction Fixtures < 100 Watt (101 - 175 Watt lamp basecase)
Fixture
$45.00
10-11
L-D61
Exterior Induction Fixtures < 70 Watts (< 100 Watts lamp basecase)
Fixture
$25.00
10-11
Interior Linear Fluorescent Fixtures
L-H11*
Interior Linear Fluorescent Fixture < 600 Watts (> 400 Watt lamp basecase)
Fixture
$200.00
11-12
L-H21*
Interior Linear Fluorescent Fixture < 244 Watts (400 Watt lamp basecase) Tier I
Fixture
$100.00
11-12
L-H31
Interior Linear Fluorescent Fixture 245 - 360 Watts (400 Watts lamp basecase) Tier II
Fixture
$50.00
11-12
L-H41
Interior Linear Fluorescent Fixture < 192 Watts (176 - 399 Watts lamp basecase)
Fixture
$50.00
11-12
L-H51*
Interior Linear Fluorescent Fixture < 128 Watts (101 - 175 Watts lamp basecase)
Fixture
$35.00
11-12
L-H61*
Interior Linear Fluorescent Fixture < 64 Watts (< 100 Watt lamp basecase)
Fixture
$25.00
11-12
Interior Pulse Start / Ceramic Metal Halide
L-F81*
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 600 Watt (> 400 Watt lamp basecase) Tier I
Fixture
$150.00
12
L-F71
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 750 Watt (> 400 Watt lamp basecase) Tier II
Fixture
$90.00
12
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
1
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
L-F61*
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 250 Watt (400 Watt lamp basecase)
Fixture
$75.00
12
L-F51*
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 175 Watt (176-399 Watt lamp basecase)
Fixture
$40.00
12
L-F41*
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 125 Watts (101-175 Watt lamp basecase)
Fixture
$35.00
12
L-F21
Interior Pulse Start/ Ceramic Metal Halide Fixtures < 70 Watts (<100 Watt lamp basecase)
Fixture
$20.00
12
Exterior Pulse Start / Ceramic Metal Fixture
L-P61
Exterior Pulse Start/Ceramic Metal Halide Lamp < 750 Watts (> 400 Watt lamp basecase)
Fixture
$75.00
12-13
L-P51
Exterior Pulse Start/Ceramic Metal Halide Lamp < 250 Watts (400 Watt lamp basecase)
Fixture
$45.00
12-13
L-P41
Exterior Pulse Start/Ceramic Metal Halide Lamp < 175 Watts (201- 399 Watt lamp basecase)
Fixture
$25.00
12-13
L-P31
Exterior Pulse Start/Ceramic Metal Halide Lamp < 125 Watts (176 - 200 Watt lamp basecase)
Fixture
$25.00
12-13
L-P21
Exterior Pulse Start/Ceramic Metal Halide Lamp < 100 Watts (101-175 Watt lamp basecase)
Fixture
$20.00
12-13
L-P11
Exterior Pulse Start/Ceramic Metal Halide Lamp < 70 Watts (< 100 Watt lamp basecase)
Fixture
$15.00
12-13
Fixture
$45.00
13
Ceramic Metal Halide
L-G11*
Ceramic Metal Halide Fixtures < 75 Watt
Interior High Bay LED Fixtures
L-S11
Interior LED Fixtures < 350 Watt (400 Watt lamp basecase)
Fixture
$200.00
13-14
L-S21
Interior LED Fixtures < 180 Watt (250 Watt lamp basecase)
Fixture
$160.00
13-14
L-S31
Interior LED Fixtures < 110 Watt (175 Watt lamp basecase)
Fixture
$85.00
13-14
L-S41
Interior LED Fixtures < 130 Watt (150 Watt lamp basecase)
Fixture
$85.00
13-14
Exterior LED Fixtures
L-S51
Exterior LED Fixtures < 350 Watt (400 Watt lamp basecase)
Fixture
$125.00
14-15
L-S61
Exterior LED Fixtures < 192 Watt (250 Watt lamp basecase)
Fixture
$125.00
14-15
L-S71
Exterior LED Fixtures < 130 Watt (200 Watt lamp basecase)
Fixture
$80.00
14-15
L-S81
Exterior LED Fixtures < 110 Watt (150 Watt lamp basecase)
Fixture
$80.00
14-15
L-S91
Exterior LED Fixtures < 80 Watt (100 Watt lamp basecase)
Fixture
$50.00
14-15
LED Display Case Lighting
L-O11
Linear LED Strip (T8 basecase)
Linear Foot
$12.00
15
L-O21
Linear LED Strip (T12 basecase)
Linear Foot
$12.00
15
L-O31
Linear LED Strip (Bi-pin Halogen basecase)
Linear Foot
$12.00
15
LED Refrigerated Case Lighting
L-R11
Premium Tier 5' Case Door
Door
$65.00
15-16
L-R21*
Standard Tier 5' Case Door
Door
$45.00
15-16
L-R31
Premium Tier 6' Case Door
Door
$100.00
15-16
L-R41*
Standard Tier 6' Case Door
Door
$75.00
15-16
Lamps
Compact Fluorescent
L-A11
Cold Cathode Lamps, 2-8 Watt
Lamp
$4.00
16
L-B41*
Screw-in Compact Fluorescent Lamp, 14-28 Watt, Reflector Lamp (Incandescent basecase)
Lamp
$7.00
16
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
2
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
Linear Fluorescent (T8/T5)
L-E11
T8 or T5 Lamp and Electronic Ballast - 2 foot (T12 Replacement only)
Lamp
$4.50
17
L-E21
T8 or T5 Lamp and Electronic Ballast - 3 foot (T12 Replacement only)
Lamp
$5.50
17
L-E31
T8 or T5 Lamp and Electronic Ballast - 4 foot (T12 Replacement only)
Lamp
$5.50
17
L-E41
T8 or T5 Lamp and Electronic Ballast - 8 foot (T12 Replacement only)
Lamp
$9.00
17
L-E5
T8 or T5 Lamp - 2 foot Lamp Removed (T12 Replacement only)
Lamp
$6.00
17-18
L-E61
T8 or T5 Lamp - 3 foot Lamp Removed (T12 Replacement only)
Lamp
$6.00
17-18
L-E71
T8 or T5 Lamp - 4 foot Lamp Removed (T12 Replacement only)
Lamp
$8.00
17-18
L-E81
T8 or T5 Lamp - 8 foot Lamp Removed (T12 Replacement only)
Lamp
$20.00
17-18
Low or Reduced Wattage (T8)
L-T11
T8 to 4 Foot 25 Watt Lamp
Lamp
$1.50
18
L-T21
T8 to 4 Foot 28 Watt Lamp
Lamp
$1.00
18
L-T31*
T8 4 Foot 25 Watt Lamp and Ballast
Lamp
$4.00
18-19
L-T41*
T8 4 Foot 28 Watt Lamp and Ballast
Lamp
$2.50
18-19
L-T51
T8 4 Foot 32 Watt Lamp Removed
Lamp
$7.50
19
Interior LED Integral Lamps
L-Q11
Interior LED Integral Lamps <10 watts LED A-lamp (<40 watts existing)
Lamp
$5.00
19-20
L-Q21
Interior LED Integral Lamps <30 watts LED A-lamp (41-100 watts existing)
Lamp
$15.00
19-20
L-Q31
Interior LED Integral Lamps <6 watts LED MR 16 (<35 watts existing)
Lamp
$5.00
19-20
L-Q41
Interior LED Integral Lamps 5-10 watts LED MR 16 (36-50 watts existing)
Lamp
$12.50
19-20
L-Q51
Interior LED Integral Lamps <15 watts LED PAR 30 (< 50 watts existing)
Lamp
$7.50
19-20
L-Q61
Interior LED Integral Lamps 10-21 watts LED PAR 30 (51-75 watts existing)
Lamp
$17.50
19-20
L-Q71
Interior LED Integral Lamps <17 watts LED PAR 38 (< 50 watts existing)
Lamp
$10.00
19-20
L-Q81
Interior LED Integral Lamps 11-25 watts LED PAR 38 (51-90 watts existing)
Lamp
$20.00
19-20
Lamp
$17.50
20
Fixture
$30.00
20
Accent/Directional Lighting
L-G21
Integrated Ballast Ceramic Metal Halide PAR Lamps < 25 Watts
L-U11
LED fixture < 15 Watts (> 40 Watt basecase) - Surface, Pendant, and Recessed Down Lighting
Controls
L-J11*
Wall-box Lighting Sensor
Sensor
$20.00
21
L-J21
Wall or Ceiling Mounted Lighting Sensor < 500 Watts
Sensor
$35.00
21
L-J31
Wall or Ceiling Mounted Lighting Sensor > 500 Watts
Sensor
$55.00
21
L-J41
Fixture Integrated Occupancy Sensors, > 150 Wattage Controlled
Sensor
$40.00
21
L-J51
Fixture Integrated Occupancy Sensors, < 150 Wattage Controlled
Sensor
$15.00
21
L-J61*
Bi-Level Stairwell/Hall/Garage Fixtures
Fixture
$25.00
22
L-K1*
Exterior Photocell
Photocell
$11.00
22
L-L11*
Time Clock
Time Clock
$36.00
22-23
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
3
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF NON-LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
Signage
L-M11*
Energy-efficient Exit Sign (Incandescent basecase)
Fixture
$27.00
23
L-M2*
Energy-efficient Exit Sign (CFL basecase)
Fixture
$15.00
23
L-N11
LED Channel Signage, Indoor < 2ft, Retrofit
Foot
$4.00
23-24
L-N21
LED Channel Signage, Indoor < 2ft, Replacement
Foot
$4.00
23-24
L-N31
LED Channel Signage, Outdoor < 2ft, Retrofit
Foot
$2.00
23-24
L-N41
LED Channel Signage, Outdoor < 2ft, Replacement
Foot
$2.00
23-24
L-N51
LED Channel Signage, Indoor > 2ft, Retrofit
Foot
$6.00
23-24
L-N61
LED Channel Signage, Indoor > 2ft, Replacement
Foot
$6.00
23-24
L-N71
LED Channel Signage, Outdoor > 2ft, Retrofit
Foot
$3.00
23-24
L-N81
LED Channel Signage, Outdoor > 2ft, Replacement
Foot
$3.00
23-24
Units
$/Units
Pages
LIST OF NON-LIGHTING PRODUCTS
Product
Code
Product Description
Food Service Itemized Measures
FS-A11
Steam Cooker (Electric)
Steamer
$1,250.00
25
FS-A21
Steam Cooker (Gas)
Steamer
$2,000.00
25
FS-B1
Insulated Holding Cabinet-Full Size
Unit
$300.00
25
FS-B2
Insulated Holding Cabinet-Three Quarter Size
Unit
$250.00
25
FS-B3
Insulated Holding Cabinet-Half Size
Unit
$200.00
25
FS-C1
Commercial Electric Fryer
Vat
$200.00
26
FS-C2
Commercial Gas Fryer
Vat
$500.00
26
FS-C3
Commercial Large Vat Electric Fryer, Cooking Efficiency > 80%
Vat
$200.00
26
FS-C4
Commercial Large Vat Gas Fryer, Cooking Efficiency > 50%
Vat
$500.00
26
FS-D8
Commercial Ice Machines, Air Cooled 101-200 lbs per 24 hrs. (ENERGY STAR®)
Unit
$50.00
27
FS-D9
Commercial Ice Machines, Air Cooled 201-300 lbs per 24 hrs. (ENERGY STAR)
Unit
$50.00
27
FS-D10
Commercial Ice Machines, Air Cooled 301-400 lbs per 24 hrs. (ENERGY STAR)
Unit
$75.00
27
FS-D11
Commercial Ice Machines, Air Cooled 401-500 lbs per 24 hrs. (ENERGY STAR)
Unit
$75.00
27
FS-D12
Commercial Ice Machines, Air Cooled 501-1,000 lbs per 24 hrs. (ENERGY STAR)
Unit
$125.00
27
FS-D13
Commercial Ice Machines, Air Cooled 1,001-1,500 lbs per 24 hrs. (ENERGY STAR)
Unit
$200.00
27
FS-D14
Commercial Ice Machines, Air Cooled > 1,500 lbs per 24 hrs. (ENERGY STAR)
Unit
$250.00
27
FS-D15
Commercial Ice Machines, Air Cooled 101-200 lbs per 24 hrs. (CEE Tier III)
Unit
$100.00
27
FS-D16
Commercial Ice Machines, Air Cooled 201-300 lbs per 24 hrs. (CEE Tier III)
Unit
$100.00
27
FS-D17
Commercial Ice Machines, Air Cooled 301-400 lbs per 24 hrs. (CEE Tier III)
Unit
$150.00
27
FS-D18
Commercial Ice Machines, Air Cooled 401-500 lbs per 24 hrs. (CEE Tier III)
Unit
$150.00
27
FS-D19
Commercial Ice Machines, Air Cooled 501-1,000 lbs per 24 hrs. (CEE Tier III)
Unit
$250.00
27
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
4
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF NON-LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
FS-D20
Commercial Ice Machines, Air Cooled 1,001-1,500 lbs per 24 hrs. (CEE Tier III)
Unit
$400.00
27
FS-D21
Commercial Ice Machines, Air Cooled > 1,500 lbs per 24 hrs. (CEE Tier III)
Unit
$500.00
27
FS-E1
Commercial Electric Griddle
Griddle
$300.00
28
FS-E2
Commercial Gas Griddle
Griddle
$125.00
28
FS-F1
Commercial Electric Combination Oven
Oven
$1,000.00
28
FS-F2
Commercial Gas Combination Oven
Oven
$750.00
28
FS-G1
Commercial Electric Convection Oven
Oven
$350.00
28
FS-G2
Commercial Gas Convection Oven
Oven
$500.00
29
FS-H11
Solid-Door Reach-In Refrigerator < 15 ft3
Unit
$50.00
29
FS-H21
Solid-Door Reach-In Refrigerator 15-29 ft3
Unit
$75.00
29
FS-H31
Solid-Door Reach-In Refrigerator 30-49 ft3
Unit
$125.00
29
FS-H41
Solid-Door Reach-In Refrigerator 50 ft3 and over
Unit
$200.00
29
FS-I11
Solid-Door Reach-In Freezer < 15 ft3
Unit
$100.00
29-30
FS-I21
Solid-Door Reach-In Freezer 15-29 ft3
Unit
$150.00
29-30
FS-I31
Solid-Door Reach-In Freezer 30-49 ft3
Unit
$300.00
29-30
FS-I41
Solid-Door Reach-In Freezer 50 ft3 and over
Unit
$600.00
29-30
FS-J51
Glass-Door Reach-In Refrigerator < 15 ft3
Unit
$75.00
30-31
FS-J61
Glass-Door Reach-In Refrigerator 15-29 ft3
Unit
$100.00
30-31
FS-J71
Glass-Door Reach-In Refrigerator 30-49 ft3
Unit
$125.00
30-31
FS-J81
Glass-Door Reach-In Refrigerator 50 ft3 and over
Unit
$150.00
30-31
FS-N11
Glass-Door Reach-In Freezer < 15 ft3
Unit
$200.00
31
FS-N21
Glass-Door Reach-In Freezer 15-29 ft3
Unit
$250.00
31
FS-N31
Glass-Door Reach-In Freezer 30-49 ft3
Unit
$500.00
31
FS-N41
Glass-Door Reach-In Freezer 50 ft3 and over
Unit
$1,000.00
31
FS-K1
Commercial Gas Rack Oven - Single
Single oven
$1,000.00
31
FS-K2
Commercial Gas Rack Oven - Double
Double oven
$2,000.00
31
FS-L1
Commercial Conveyor Oven, Small (< 25" Total conveyor width)
Deck
$500.00
32
FS-L2
Commercial Conveyor Oven, Large (> 25" Total conveyor width)
Deck
$750.00
32
FS-M1
Commercial Kitchen Ventilation Control - Retrofit (Electric)
Fan hp
$350.00
32
FS-M2
Commercial Kitchen Ventilation Control - New Hood (Electric)
Fan hp
$300.00
32
Refrigeration Itemized Measures
R-A11*
Night Covers for Multi-deck and Horizontal Display Cases (Medium temp)
Linear foot
$3.50
33
R-A21
Night Covers for Multi-deck and Horizontal Display Cases (Low temp)
Linear foot
$3.50
33
R-B1
Strip Curtains for Walk-ins Boxes - Product closed effective March 31, 2011
Square foot
$3.00
33-34
R-C11
New Refrigeration Display Case with Doors (Low temp)
Linear foot
$175.00
34
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
5
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF NON-LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
R-C21
New Refrigeration Display Case with Doors (Medium temp)
Linear foot
$75.00
34
R-D11
New High Eff. Refrigeration Display Case with Special Doors (Low temp)
Linear foot
$75.00
34-35
R-E11
Special Doors with Low/No Anti-Sweat Heat on Low Temp Display Case
Door
$100.00
35
R-F11*
Anti-Sweat Heat (ASH) Controls
Linear foot
$25.00
35
R-G11*
Insulation for Bare Suction Lines
Linear foot
$2.00
35-36
R-H11
Door Gaskets on Reach In Doors - Product closed September 30, 2010
Linear foot
$2.00
36
R-I11
Door Gaskets on Main Walk In Doors - Product closed September 30, 2010
Linear foot
$2.00
36
R-J11*
Auto-Closer for Main Cooler Doors
Closer
$75.00
37
R-J21*
Auto-Closer for Main Freezer Doors
Closer
$75.00
37
R-K1
Evaporative Fans Controller for Walk-in Coolers
Controller
$75.00
37
R-K2
Evaporative Fans Controller for Walk-in Freezers
Controller
$75.00
37
R-L11*
Efficient Evaporator Fan Motor - Electronically Commutated Motor (ECM) Display Case
Motor
$35.00
37-38
R-L21
Efficient Evaporator Fan Motor - Permanent Split Capacitor (PSC) Motor
Motor
$50.00
37-38
R-L31*
Efficient Evaporator Fan Motor - Electronically Commutated Motor (ECM) Walk-In
Motor
$50.00
37-38
Natural Gas Itemized Measures
G-A1
Storage Water Heater
MBtuh
$2.00
39
G-B1
Space Heating Boiler (Steam)
MBtuh
$0.25
39
G-B2
Space Heating Boiler (Water)
MBtuh
$0.25
39
G-B3
Space Heating Boiler (Large)
MBtuh
$0.25
39
G-C1
Commercial Boiler
MBtuh
$0.50
40
G-D1
Instantaneous Water Heater, Small (< 200 MBtuh)
MBtuh
$2.00
40
G-D2
Instantaneous Water Heater, Large (> 200 MBtuh)
MBtuh
$0.50
40
G-E1
Process Boiler (Steam)
MBtuh
$0.50
40-41
G-E2
Process Boiler (Water)
MBtuh
$0.50
40-41
G-F1
Commercial Pool and Spa Heater
MBtuh
$2.00
41
G-G1
Direct Contact Water Heater, > 300 MBtuh
MBtuh
$2.00
41
G-G2
Direct Contact Water Heater, < 300 MBtuh
MBtuh
$2.00
41
G-H11
Pipe Insulation Low Pressure (< 15 psi) Steam Applic. < 1 in
Linear foot
$3.00
41-42
G-H21
Pipe Insulation Low Pressure (< 15 psi) Steam Applic. > 1 in
Linear foot
$3.00
41-42
G-H31*
Pipe Insulation Hot Water Application < 1 in
Linear foot
$2.00
41-42
G-H41
Pipe Insulation Hot Water Application > 1 in
Linear foot
$2.00
41-42
G-H51
Pipe Insulation Medium Pressure (> 15 psi) Steam Application < 1 in
Linear foot
$3.00
41-42
G-H61
Pipe Insulation Medium Pressure (> 15 psi) Steam Application > 1 in
Linear foot
$3.00
41-42
G-H71
Pipe Insulation High Pressure (> 15 psi) Dry Cleaner Steam Application > 1 in
Linear foot
$3.00
41-42
G-I1
Tank Insulation High Temperature Application 1 in
Square foot
$3.00
42
G-I2
Tank Insulation High Temperature Application 2 in
Square foot
$4.00
42
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
6
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF NON-LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product
Code
Product Description
Units
$/Units
Pages
G-I3
Tank Insulation Low Temperature Application 1 in
Square foot
$2.00
42
G-I4
Tank Insulation Low Temperature Application 2 in
Square foot
$3.00
42
G-J1
High Efficiency Clothes Washer, CEE Tier 2 and 3A Models
Unit
$35.00
42-43
G-J2
High Efficiency Clothes Washer, CEE Tier 3B Models
Unit
$75.00
42-43
G-M1
Steam Trap Replacement, Commercial Operating System < 12 hrs./day, Dry Cleaners Excluded
Unit
$100.00
43
G-M2
Steam Trap Replacement, Industrial < 15 psig, Commercial Operating System 12-24 hrs./day
Unit
$100.00
43
G-M3
Steam Trap Replacement, Industrial > 15 psig — Product closed April 17, 2012
Unit
$200.00
43
G-N11
Ozone Laundry System (Purchased & installed on or after February 17, 2012)
LB
$39.00
44
Acre
$44.00
45
Nozzle
$1.15
45
Agricultural Itemized Measures
O-C1
Sprinkler to Drip Irrigation
O-D1
Low Pressure Sprinkler Nozzles
G-K1
Greenhouse Heat Curtain — Requires Pre-inspection
Square foot
$0.20
45-46
G-L1
Infrared Film for Greenhouses
Square foot
$0.05
46
O-G1
Wine Tank Insulation-Indoor Tank — Product closed December 31, 2011
Square foot
$2.25
46
O-G2
Wine Tank insulation-Outdoor Tank- Coastal — Product closed December 31, 2011
Square foot
$3.00
46
O-G3
Wine Tank insulation-Outdoor Tank- Inland — Product closed December 31, 2011
Square foot
$3.75
46
Motors
M-A1
Premium Efficiency Motors 1 HP
Motor
$35.00
47-48
M-A2
Premium Efficiency Motors 1.5 HP
Motor
$35.00
47-48
M-A3
Premium Efficiency Motors 2 HP
Motor
$35.00
47-48
M-A4
Premium Efficiency Motors 3 HP
Motor
$40.00
47-48
M-A5
Premium Efficiency Motors 5 HP
Motor
$50.00
47-48
M-A6
Premium Efficiency Motors 7.5 HP
Motor
$60.00
47-48
M-A7
Premium Efficiency Motors 10 HP
Motor
$70.00
47-48
M-A8
Premium Efficiency Motors 15 HP
Motor
$80.00
47-48
M-A9
Premium Efficiency Motors 20 HP
Motor
$90.00
47-48
M-A10
Premium Efficiency Motors 25 HP
Motor
$135.00
47-48
M-A11
Premium Efficiency Motors 30 HP
Motor
$230.00
47-48
M-A12
Premium Efficiency Motors 40 HP
Motor
$300.00
47-48
M-A13
Premium Efficiency Motors 50 HP
Motor
$320.00
47-48
M-A14
Premium Efficiency Motors 60 HP
Motor
$355.00
47-48
M-A15
Premium Efficiency Motors 75 HP
Motor
$540.00
47-48
M-A16
Premium Efficiency Motors 100 HP
Motor
$720.00
47-48
M-A17
Premium Efficiency Motors 125 HP
Motor
$945.00
47-48
M-A18
Premium Efficiency Motors 150 HP
Motor
$1,260.00
47-48
M-A19
Premium Efficiency Motors 200 HP
Motor
$1,260.00
47-48
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
7
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
LIST OF NON-LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Other Technology Itemized Measures
Product
Code
Product Description
Units
$/Units
Pages
O-A1
Reflective Window Film (Coastal)
Square foot
$1.35
49
O-A2
Reflective Window Film (Inland)
Square foot
$1.35
49
O-A3
Reflective Window Film (Desert)
Square foot
$1.35
49
SD-A1
Plug Load Occupancy Sensor
Sensor
$15.00
49
SD-B1*
Low Flow Showerhead
Showerhead
$20.00
50
SD-C1
Network Power Management Software
Desktop
Computer
$15.00
50
SD-D1
High Efficiency Copier
Unit
$100.00
50
SD-E1
Early Retirement Refrigerator
Unit
$275.00
50-51
R-O1*
Vending Machine Controller
Controller
$100.00
51
O-B1
Variable Frequency Drives (VFDs)
Hp
$80.00
51
*This product is offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit
sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
8
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
Energy Efficiency Business Rebates
Terms & Conditions
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: LIGHTING PRODUCTS
You must attach the manufacturer’s specification sheet to each application documenting the characteristics of lamps,
ballasts and fixtures.
GENERAL REQUIREMENTS
 Customers must have a San Diego Gas & Electric® (SDG&E®) commercial electric account
 Carefully read the specifications below to determine whether you are installing a qualifying product(s)
 Everything must be installed and operational before a rebate application is submitted
 All new lighting fixtures, retrofit kits, and components must carry the appropriate, designated Underwriters
Laboratory (UL) or Intertek’s ETL Listed Mark
 In all cases, the wattage of the replacement fixture must be less than the wattage of the existing lamp. The maximum replacement fixture wattage listed in the table for each category is typically associated with the highest lamp
wattage in that particular range
 All installations must be new replacements or retrofits and are based on a one-for-one replacement
 Customer must submit the existing and new equipment wattage and technology type when applicable
 It is the responsibility of the customer/project sponsor to ensure the equipment to be installed adheres to all state,
local and national building codes and ordinances, as well as the manufacturer’s requirements.
 Include ballast and lamp model number on invoice when ballast and lamp specification requirements are listed in
the terms and conditions.
Example: Based on an Existing 400 watt Standard Metal Halide Lamp
Product
Code
L-H21
Product Description
Interior Linear Fluorescent Lamp, < 244 watts
(400 Watt lamp base case) Tier I
Units
$/Units
A
"# of Units
B"
Rebate Total
(A x B = C)
New Lamp
& Ballast
Wattage
Fixture
$100.00
1
$100.00
234
Existing
Lamp &
Ballast
Wattage
Existing
Technology
(Refer to
Ts&Cs for
acceptable
options)
458
MH
FIXTURES
COMPACT FLUORESCENT FIXTURES
New Fixture – Refers to new equipment being installed based on system (lamp and ballast) wattage
Existing Fixture Wattage - Refers to the lamp wattage used in the fixture
Requirements:
 Only complete, new Compact Fluorescent fixtures qualify
 New fixture must replace an existing fixture that is either an Incandescent, Mercury Vapor, Standard Metal Halide or
High Pressure Sodium
 New fixture wattage must be less than the wattage of lamp being replaced
 Ballast Power Factor (PF) must be greater than or equal to 0.9
 Ballast must have a Total Harmonic Distortion (THD) of less than or equal to 20%
 Fixture must be hardwired
9
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Additional Details:
 May qualify for an additional rebate through Occupancy Sensor or Photocell category, provided all requirements are met
Table 1: Compact Fluorescent Fixtures
Product Code
Existing Lamp Wattage
New Fixture Wattage
Rebate/Unit
L-C41
Interior 400 Watt Lamp (Tier I)
< 244 Watt
$75.00/fixture
L-C51
Interior 400 Watt Lamp (Tier II)
< 360 Watt
$45.00/fixture
L–C31
Interior 176 - 399 Watt Lamp
< 192 Watt
$40.00/fixture
L-C21
Interior 101 - 175 Watt Lamp
< 128 Watt
$35.00/fixture
L-C11*
Interior < 100 Watt Lamp
< 70 Watt
$20.00/fixture
L-C61
Exterior < 100 Watt Lamp
< 70 Watt
$17.00/fixture
*Product code L-C11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
INTERIOR INDUCTION FIXTURES
Fixture – Refers to new equipment being installed based on system (lamp and driver) wattage
Requirements:
 Only complete new Induction fixtures or retrofit kits qualify
 New fixture and retrofit kits wattage must be less than the wattage of the lamp being replaced
 New fixtures and retrofit kits must be equipped with Induction lamps and drivers
 New fixtures and retrofit kits must replace an existing lamp that is either an Incandescent, T12 High Output Fluorescent,
T12 Very High Output Fluorescent, Standard Metal Halide, Mercury Vapor, Low Pressure Sodium, or High Pressure Sodium
 New fixtures must not exceed the maximum wattage listed in Table 2 for each range of lamp wattage being replaced
 Fixture must be hardwired
Exclusions:
 No exterior installations (Refer to Exterior Induction Category)
Additional Details:
 May qualify for an additional rebate through the Occupancy Sensor category, provided all requirements are met
Table 2: Interior Induction Fixtures
Product Code
Existing Lamp Wattage
New Lamp Wattage
Rebate/Unit Measure
L-D41
400 Watt Lamp (Tier I)
< 250 Watt
$125.00/fixture
L-D51
400 Watt Lamp (Tier II)
< 360 Watt
$60.00/fixture
L-D31
176 - 399 Watt Lamp
< 180 Watt
$75.00/fixture
L-D21
101 - 175 Watt Lamp
< 120 Watt
$60.00/fixture
L-D11
< 100 Watt Lamp
< 70 Watt
$35.00/fixture
EXTERIOR INDUCTION FIXTURES
Fixture – Refers to new equipment being installed based on system (lamp and driver) wattage
Requirements:
 Only complete new Induction fixtures or retrofit kits qualify
 New fixtures and retrofit kits must be equipped with Induction lamps and drivers
 New fixtures and retrofit kits must replace an existing lamp that is either an Incandescent, T12 High Output Fluorescent,
T12 Very High Output Fluorescent, Standard Metal Halide, Mercury Vapor, Low Pressure Sodium or High Pressure Sodium
 New fixtures and retrofit kits must not exceed the maximum wattage listed in Table 3 for each range of lamp wattage
being replaced
 Fixture must be hardwired
10
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Exclusions:
 No interior installations (Refer to Interior Induction Category)
 Replacement of Pulse-Start Metal Halide does not qualify
Additional Details:
May qualify for an additional Photocell rebate, provided all requirements are met
Other fixture configurations may be considered under our Energy Efficiency Business Incentives
Customers are responsible for determining whether retrofit will maintain adequate light levels
Table 3: Exterior Induction Fixtures
Product Code
Existing Lamp Wattage
New Lamp Wattage
Rebate/Unit Measure
L-D01
400 Watt Lamp
< 250 Watt
$100.00/fixture
L-D91
201 - 399 Watt Lamp
< 180 Watt
$50.00/fixture
L-D81
176 - 200 Watt Lamp
< 120 Watt
$50.00/fixture
L-D71
101 - 175 Watt Lamp
< 100 Watt
$45.00/fixture
L-D61
< 100 Watt Lamp
< 70 Watt
$25.00/fixture
INTERIOR LINEAR FLUORESCENT FIXTURES
Fixture – Refers to new equipment being installed based on system (lamp and ballast) wattage
Requirements:
 All 32 Watt T8 lamps must be High Performance T8 or Super T8 lamps, and listed on the qualified High
Performance T8 lamp list at www.cee1.org
 Replacement fixture wattage must be less than existing lamp wattage
 All lamps must be rated greater than or equal to 20,000 hours average rated lamp life, based on 3 hours per start
when operated on a program start ballast
 Only complete, new T8, T5 or T5 High Output (HO) Interior Linear Fluorescent fixtures qualify
 T5 high output and T8 very high output lamps must have color rendering index (CRI) that is greater than or equal to 82,
all other lamps must have a CRI that is greater than or equal to 80
 Must replace an existing lamp that is either an Incandescent, Standard Metal Halide, Mercury Vapor, High Pressure
Sodium, 8-foot T12 slimline, T12 HO Fluorescent or T12 Very HO Fluorescent
 All T8 ballasts must be NEMA premium or designated high performance electronic ballast listed on www.cee1.org.
T5 high output and T8 very high output must be program rapid start ballasts
 New fixtures must not exceed the maximum wattage listed in the rebate table below for each range of lamp wattage
being replaced
Exclusions:
 Exterior installations do not qualify but may be considered under our Energy Efficiency Business Incentives
 Not eligible for additional rebates under the Compact Fluorescent Fixtures and T8/T5 Linear Fluorescent Lamps
with Electronic Ballasts category
 Replacement of Pulse-Start Metal Halide does not qualify
Additional Details:
 May qualify for an additional rebate through the Occupancy Sensor category, provided all requirements are met
11
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 4: Interior Linear Fluorescent Fixtures
Product Code
Existing Lamp Wattage
New Fixture Wattage
Rebate/Unit Measure
L-H11*
> 400 Watt Lamp
< 600 Watt
$200.00/fixture
L-H21*
400 Watt Lamp (Tier I)
< 244 Watt
$100.00/fixture
L-H31
400 Watt Lamp (Tier II)
245 - 360 Watt
$50.00/fixture
L-H41
176 - 399 Watt Lamp
< 192 Watt
$50.00/fixture
L-H51*
101 - 175 Watt Lamp
< 128 Watt
$35.00/fixture
L-H61*
< 100 Watt Lamp
< 64 Watt
$25.00/fixture
*Product code(s) L-H11, L-H21, L-H51, and L-H61 are offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy
Savings Center at 1-800-644-6133
INTERIOR PULSE START/CERAMIC METAL HALIDE FIXTURES WITH ELECTRONIC BALLAST
Fixture – Refers to new equipment being installed based on system (lamp and ballast) wattage
Requirements:
 Complete new Pulse-Start Metal Halide fixtures and retrofit kits qualify
 Complete new Ceramic Metal Halide fixtures with electronic ballasts and retrofit kits with electronic ballasts qualify
 Replacement fixture wattage must be less than existing lamp wattage
 Retrofit kits may be used on existing Mercury Vapor, Standard Metal Halide or High Pressure Sodium only
 New fixture may be used on existing Incandescent, Mercury Vapor, T12/High Output Fluorescent, T12/Very High
Output Fluorescent, Standard Metal Halide, or High Pressure Sodium Fixtures
 Replacement lamps must not exceed the maximum wattage listed in Table 5 for each range of lamp wattage being replaced
Exclusions:
 No exterior installations (Refer to Exterior Pulse-Start category)
 Ceramic Metal Halide lamps less than or equal to 70 watts do not qualify in this category (Refer to Ceramic Metal
Halide fixture measure for lower wattages)
Table 5: Interior Pulse Start/Ceramic Metal Halide Fixtures with Electronic Ballast
Product Code
Existing Lamp Wattage
New Lamp Wattage
Rebate/Unit Measure
L-F81*
> 400 Watt Lamp (Tier I)
< 600 Watt
$150.00/fixture
L-F71
> 400 Watt Lamp (Tier II)
< 750 Watt
$90.00/fixture
L-F61*
400 Watt Lamp
< 250 Watt
$75.00/fixture
L-F51*
176 - 399 Watt Lamp
< 175 Watt
$40.00/fixture
L-F41*
101 - 175 Watt Lamp
< 125 Watt
$35.00/fixture
L-F21
< 100 Watt Lamp
< 70 Watt (PSMH Only)
$20.00/fixture
*Product code(s) L-F41, L-F51, L-F61, and L-F81 are offered at no cost for customers with monthly electrical demand
under 100 kilowatts (kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our
Energy Savings Center at 1-800-644-6133
EXTERIOR PULSE START/ CERAMIC METAL HALIDE FIXTURES WITH ELECTRONIC BALLAST
Fixture – Refers to new equipment being installed based on system (lamp and ballast) wattage
Requirements:
 Complete new Pulse-Start Metal Halide fixtures and retrofit kits qualify
 Complete new Ceramic Metal Halide fixtures with electronic ballasts and retrofit kits with electronic ballasts qualify
12
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
 Replacement fixture wattage must be less than existing lamp wattage
 Retrofit kits and new fixtures must not exceed the maximum wattage listed in Table 6 for each range of lamp
wattage being replaced
 Retrofit kits may be used on existing Mercury Vapor, Standard Metal Halide, Low Pressure Sodium or High Pressure
Sodium only
 New fixture may be used on existing Incandescent, Mercury Vapor, T12/High Output Fluorescent, T12/Very High
Output Fluorescent, Standard Metal Halide, Low Pressure Sodium or High Pressure Sodium Fixture
Additional Details:
 Customers are responsible for deciding whether retrofit will maintain adequate light levels
Exclusions:
 No interior installations (Refer to Interior Pulse-Start Category)
Table 6: Exterior Pulse Start/Ceramic Metal Halide Fixtures with Electronic Ballast
Product Code
Existing Lamp Wattage
New Lamp Wattage
Rebate/Unit Measure
L-P61
> 400 Watt Lamp
< 750 Watt
$75.00/fixture
L-P51
400 Watt Lamp
< 250 Watt
$45.00/fixture
L-P41
201 – 399 Watt Lamp
< 175 Watt
$25.00/fixture
L-P31
176 – 200 Watt Lamp
< 125 Watt
$25.00/fixture
L-P21
101 - 175 Watt Lamp
< 100 Watt
$20.00/fixture
L-P11
< 100 Watt Lamp
< 70 Watt
$15.00/fixture
CERAMIC METAL HALIDE FIXTURES
Requirements:
 Must replace existing incandescent, PAR halogen or PAR halogen IR lamps with a less than or equal to
75 watt Ceramic Metal Halide fixture for accent lighting, flood lighting or down lighting in interior installations
Table 7: Ceramic Metal Halide Fixtures
Product code
L-G11*
Description
< 75 Watt Ceramic Metal Halide
Rebate/Unit Measure
$45.00/fixture
*Product code L-G11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW)through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
INTERIOR HIGH BAY LED FIXTURES
Fixture – Refers to new equipment being installed based on system wattage
Requirements:
 All fixtures must be ENERGY STAR or utility approved
 Only complete, new LED fixtures qualify
 Must replace an existing Standard Metal Halide, High Pressure Sodium lamp, Mercury Vapor, Low Pressure Sodium
or Incandescent lamp
 Must not exceed the maximum wattage listed in Table 8 below for each range of lamp wattage being replaced
 Replacement fixture wattage must be less than existing lamp wattage
 A written warranty must be issued to the customer guaranteeing repair or replacement of defective electrical parts
(including light source and power supplies) for a minimum of three (3) years from the date of purchase
 A product cut sheet and installation instructions must be provided
 LED lamps must be RoHS compliant
13
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Power Supply Requirements:
 An electronic power supply must be used in the new fixture
 Must have a Power Factor (PF) of greater than or equal to 0.9
 Must experience no more than 20% of total harmonic distortion
Exclusions:
 Existing Pulse-Start Metal Halide installations do not qualify
Additional details:
 May qualify for an additional control(s) rebate with an Occupancy Sensor provided all requirements are met
Table 8: Interior High Bay LED Fixtures
Product Code
Existing Lamp Wattage
New Fixture Wattage
Rebate/Unit
L-S11
400 Watt Lamp
< 350 Watt
$200.00/fixture
L-S21
250 Watt Lamp
< 180 Watt
$160.00/fixture
L-S31
175 Watt Lamp
< 110 Watt
$85.00/fixture
L-S41
150 Watt Lamp
< 130 Watt
$85.00/fixture
EXTERIOR LED FIXTURES (STREET AND AREA LIGHTING)
Fixture – Refers to new equipment being installed based on system wattage
Requirements per fixture:
 Only complete, new LED fixtures qualify
 Must replace an existing Standard Metal Halide, High Pressure Sodium, Mercury Vapor, Low Pressure Sodium or
Incandescent lamp
 Must not exceed the maximum wattage listed in Table 9 below for each range of lamp wattage being replaced
 New fixture wattage must be less than existing lamp wattage
 New fixture must be ENERGY STAR qualified or utility approved
 Must meet a minimum luminaire efficacy of greater than or equal to 40 lumens per watt
 A written warranty must be issued to the customer guaranteeing repair or replacement of defective electrical parts
(including light source and power supplies) for a minimum of three (3) years from the date of purchase.
 A product cut sheet and installation instructions must be provided
 LED lamps must be RoHS compliant
Power Supply Requirements:
 An electronic power supply must be used in the new fixture
 Must have a Power Factor (PF) of greater than or equal to 0.9
 Must experience no more than 20% of total harmonic distortion
Exclusions:
 Interior installations do not qualify
 Induction lamps do not qualify
Additional Details:
 May qualify for an additional photocell rebate provided all requirements are met
14
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 9: Exterior LED Fixtures (Street and Area Lighting)
Product Code
Existing Lamp Wattage
New Fixture Wattage
Rebate/Unit
L-S51
400 Watt
< 350 Watt
$125.00/fixture
L-S61
250 Watt
< 192 Watt
$125.00/fixture
L-S71
200 Watt
< 130 Watt
$80.00/fixture
L-S81
150 Watt
< 110 Watt
$80.00/fixture
L-S91
100 Watt
< 80 Watt
$50.00/fixture
LED DISPLAY CASE LIGHTING
Requirements:
 All fixtures must be ENERGY STAR or utility approved
 Only complete, new Linear LED fixtures qualify
 Must replace an existing bi-pin halogen or linear fluorescent fixture
 Fixture wattage must be less than existing lamp wattage
 A written warranty must be issued to the customer guaranteeing repair or replacement of defective electrical parts
(including light source and power supplies) for a minimum of three (3) years from the date of purchase
 Fixture must be RoHS compliant
Power Supply Requirements:
 An electronic power supply must be used in the new fixture
 Must have a Power Factor (PF) of greater than or equal to 0.9
 Must experience no more than 20% of total harmonic distortion
Exclusions:
 Refrigerated cases do not qualify under this category
Table 10: LED Display Case Lighting
Product code
Existing Lamp
New Fixture
Rebate/Unit Measure
L-O11
T8
Linear LED Strip
$12.00/ linear foot
L-O21
T12
Linear LED Strip
$12.00/ linear foot
L-O31
Bi-pin Halogen
Linear LED Strip
$12.00/ linear foot
LED REFRIGERATED CASE LIGHTING
Requirements:
 All fixtures must be ENERGY STAR or utility approved
 Replacement lamps must meet the Color Rendering Index (CRI) , the color temperature (CCT) and the luminaire
efficacies (lm/W) standards listed in Table 11 below
Table 11: CRI, CCT and lm/W requirements
Lamp Type & Size
CRI
CCT
lm/W
Premium Tier: All sizes & types
> 70
< 5700 K
> 35
Standard Tier: All sizes & Types
> 70
< 5700 K
> 25
 Must replace fluorescent lighting
 Must not exceed the maximum ”New lamp” wattage listed in Table 12 for each lamp type and size being replaced
 Must have a product warranty of three (3) years
 A product cut sheet and installation instructions must be provided by the manufacturer or vendor to the end use customer
15
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Power Supply Requirements
 An electronic power supply must be used in the new fixture
 LED power supply and driver must have an efficiency of 85% or greater at 120 volts
 Must have a Power Factor (PF) of greater than or equal to 0.9
 Must experience no more than 20% of total harmonic distortion
 Must have a minimum operating temperature of -20 °C or below
Table 12: Refrigerated Case Lighting
Product Code
†
Light Location
Center †
Light Location
End†
Measure Description
Rebate/Unit
Measure
L-R11
Premium Tier 5’ Case Door
19 W
38 W
$65.00/door
L-R21*
Standard Tier 5’ Case Door
25 W
50 W
$45.00/door
L-R31
Premium Tier 6’ Case Door
23 W
46 W
$100.00/door
L-R41*
Standard Tier 6’ Case Door
30 W
59 W
$75.00/door
Maximum power consumption
*Product code(s) L-R21 and L-R41 are offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center
at 1-800-644-6133
LAMPS
COLD CATHODE LAMPS
Requirements:
 Must replace incandescent lamps that are greater than or equal to 10 Watts
 Must have a wattage level between 2 and 8 Watts, and can be a screw-in lamp with either medium (Edison) or
candelabra base
 Must be rated for at least 18,000 average life hours
Table 13: Cold Cathode Lamps
Product Code
L-A11
Description
2-8 Watt Cold Cathode Lamps
Rebate/Unit Measure
$4.00/lamp
SCREW-IN COMPACT FLUORESCENT LAMPS (COVERED REFLECTOR)
Requirements:
 Lamps must be listed as ENERGY STAR qualified and be Model Type “Covered Reflector” at
http://www.energystar.gov
 Screw-in induction and electrodless reflector lamps also qualify
Exclusions:
 Detachable reflectors are not eligible
Table 14: Screw-In Compact Fluorescent Lamps
Product code
L-B41*
Description
Screw-in Compact Fluorescent,
14-28 Watts, Reflector Lamps
(Incandescent Basecase)
Rebate/Unit Measure
$7.00/lamp
*Product code L-B41 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
16
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
T8 OR T5 LINEAR FLUORESCENT LAMPS WITH ELECTRONIC BALLASTS
Lamp Requirements:
 Must replace an existing T12 lamp
 Must meet the Color Rendering Index (CRI) and Minimum Rated Lamp Life standards listed in Table 15
 Only 4 foot T8 lamps must be listed at www.cee1.org
Table 15: Lamp and Ballast Requirements Table
Lamp Type & Size
Ballast Type
Minimum Rated Lamp
Life (3 Hrs/Start)
CRI
T8: 2-ft, 3-ft, 4-ft
Programmed Start or
Programmed Rapid-Start
> 80
24,000 hours
T8: All sizes
Instant Start
> 80
18,000 hours
T5: All sizes
Programmed Start or
Programmed Rapid-Start
> 82
20,000 hours
Ballast Requirements:
 Only for 4 foot T8 lamps, new ballast must be designated as NEMA Premium electronic ballast or listed as a High
Performance T8 Ballast at www.cee1.org
 Must be warranted against mechanical or electrical defects for five (5) years
 Must have a Power Factor (PF) of greater than or equal to 0.9
 Must have a Total Harmonic Distortion (THD) of less than or equal to 20% at full light output for 4-foot and 8-foot
lamps and less than or equal to 32% for 2-foot and 3-foot lamps
Exclusions (T8 and T5):
 Replacement lamps and ballasts rebated in this category are not eligible for rebates through the Interior Linear
Fluorescent Fixtures category
Additional Details:
 Refer to www.cee1.org for acceptable lamp and ballast combination
 May qualify for an additional rebate under Occupancy Sensor and/or Photocell category, provided all requirements are met
 T8 and T5: Program start ballasts are designed to provide maximum lamp life in frequent lamp starting applications
such as in areas where occupancy sensor controls are used
 T8 Only: Instant-start electronic ballasts are the most popular type of electronic ballast today because they provide
maximum energy savings and start lamps without delay
Table 16: Linear Fluorescent Lamps with Electronic Ballasts
Product code
Description
Rebate/Unit Measure
L-E11
2-ft Lamp
$4.50/lamp
L-E21
3-ft Lamp
$5.50/lamp
L-E31
4-ft Lamp
$5.50/lamp
L-E41
8-ft Lamp
$9.00/lamp
T-12 DE-LAMPING
De-lamping – the permanent removal of existing T12 lamps, ballasts and unused lamp holders (tombstones) from existing
fixtures without replacing the lamps.
Requirements:
 The total number of lamps claimed for de-lamping cannot be more than the number of replacement T8 or T5 lamps installed
 Customers must not remove more than half of the existing lamps, ballasts and lamp holders from each fixture
17
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
 Removing lamps from a T12 fixture that is not being retrofitted with T8 lamps are not eligible for this incentive
 De-Lamping must be accompanied with lamp and ballast replacement/retrofit
Additional Details:
 Customers are responsible for determining whether de-lamping will maintain adequate light levels
Table 17: T-12 De-Lamping
Product code
Description
Rebate/Unit Measure
L-E5
2-ft Lamp Removed
$6.00/lamp removed
L-E61
3-ft Lamp Removed
$6.00/lamp removed
L-E71
4-ft Lamp Removed
$8.00/lamp removed
L-E81
8-ft Lamp Removed
$20.00/lamp removed
LOW OR REDUCED-WATTAGE T8 LAMPS (28 & 25 WATT)
Rebates are for the installation of 4-ft Low wattage T8 lamps that replace 32 watt T8 lamps. Low wattage lamp rebate
can be combined with the T12 to T8 retrofit measure.
Example A Retrofit: 4 foot T12 4-lamp fixture, with 4 foot 28W T8 lamps. (4 lamps with ballast) Rebate equals the T12 to
T8 lamp and ballast retrofit of $5.50 per lamp (L-E31), plus the low-wattage T8 rebate of $1.00 per lamp (L-T21) for a total
rebate of $26.00.
Example B Retrofit: Replace a 4 foot T8 32 Watt lamp only with a 25 Watt T8 lamp. Rebate equals $1.50 (L-T11)
Requirements:
 Approved lamps can be found at www.cee1.org
Exclusions:
 Replacement lamps rebated in this category are not eligible for additional rebates through the Interior Linear
Fluorescent Fixtures category
Additional Details:
 Low wattage T8 lamps are best used to replace 700 series 32 W T8 lamps in existing lighting fixtures. Care should
be taken to read Manufacturer recommendations for ballast requirement and use in low temperature applications
Table 18: Low or Reduced-Wattage T8 Lamp (28 and 25 Watt)
Product code
Description
Rebate/Unit Measure
L-T11
T8 to 4-ft 25 Watt Lamp
$1.50/lamp
L-T21
T8 to 4-ft 28 Watt Lamp
$1.00/lamp
T8 TO T8 REDUCED WATTAGE INTERIOR LAMP AND NEMA PREMIUM BALLAST REPLACEMENT
Rebates are for the installation of 4ft 28-watt or 25-watt T8 fluorescent lamps and NEMA Premium ballast(s) that
replace an existing 4-foot 32-watt T8 fluorescent lamps and ballast(s).
Requirements:
 Existing Lamp and ballast(s) must be retrofitted to a newer generation 4-foot, T8 lamp that uses 28 or 25 watts
and high-efficiency electronic ballast(s).
 Approved lamps and ballasts can be found at www.cee1.org
Exclusions:
 Replacement lamps in this category are not eligible for additional rebates through the Interior Linear Fluorescent
Fixture category
18
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Additional Details:
 Low Wattage T8 lamps are best used to replace 700 or 800 series 32W T8 Lamps in existing lighting systems. Care
should be taken to read manufacturer recommendations for ballast requirements and use in low temperature applications
Table 19: Low or Reduced Wattage T8 System (Lamps & Ballast)
Product Code
Description
Rebate/Unit
L-T31*
T8 to 4 foot 25 Watt Lamp & Ballast
$4.00/lamp
L-T41*
T8 to 4 foot 28 Watt Lamp & Ballast
$2.50/lamp
*Product code(s) L-T31 and L-T41 are offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center
at 1-800-644-6133
T8 DE-LAMPING
De-lamping – the permanent removal of a limited number of existing T-8 lamps, ballasts and unused lamp holders
(tombstones) from existing fixtures.
Requirements:
 The total number of lamps claimed for de-lamping cannot be more than the number of replacement T8 lamps installed
 Customers must not remove more than half of the existing lamps, ballasts and lamp holders from each fixture/system
 Removing lamps from a standard 700 or 800 series 32W T8 fixture that is not being retrofitted with reduced or
lower wattage T8 lamps are not eligible for this incentive
 De-Lamping must be accompanied with lamp and ballast replacement/retrofit
Additional Details:
 Customers are responsible for determining whether de-lamping will maintain adequate light levels
Table 20: T8 De-lamping
Product Code
L-T51
Description
T8 32 watt 4 foot Lamp Removed
Rebate/Unit
$7.50/lamp removed
INTERIOR LED INTEGRAL LAMPS - Purchased & Installed on or after 3/01/2012
Requirements:
 The new interior LED integral lamps (screw-based or pin-based) must be ENERGY STAR® qualified.
 LED A-lamps and LED PAR-lamps must replace existing incandescent, halogen, or compact flourescent lamps.
 LED MR-16 lamps must replace existing incandescent or halogen lamps.
 New LED lamp wattage must be less than the wattage of the replaced incandescent or halogen lamp.
 Wattages for existing lamp and the new LED lamp must be within wattage ranges listed in Table 21
 New LED lamps must be compatible with existing lighting controls and/or fixture components. Customers are responsible for verifying compatibility with existing lighting controls.
Exclusions:
 Replacement of Compact Fluorescent Lamps (CFL) with LED MR-16’s do not qualify
Additional Details:
 Rebate based on lamp wattage, not total fixture wattage.
 Customers are responsible for maintaining adequate light levels, as well as lamp and fixture compatibility to ensure
proper fixture performance levels are met.
19
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 21: LED Integral Lamps
Product Code
Existing Lamp Wattage
New Lamp Wattage
Rebate/Unit
L-Q11
< 40 watts
<10 watts LED A-lamp
$5.00/lamp
L-Q21
41-100 watts
<30 watts LED A-lamp
$15.00/lamp
L-Q31
< 35 watts
<6 watts LED MR 16
$5.00/lamp
L-Q41
36-50 watts
5-10 watts LED MR 16
$12.50/lamp
L-Q51
< 50 watts
<15 watts LED PAR 30
$7.50/lamp
L-Q61
51-75 watts
10-21 watts LED PAR 30
$17.50/lamp
L-Q71
< 50 watts
<17 watts LED PAR 38
$10.00/lamp
L-Q81
51-90 watts
11-25 watts LED PAR 38
$20.00/lamp
ACCENT/DIRECTIONAL LIGHTING
INTEGRATED BALLAST CERAMIC METAL HALIDE PAR LAMPS
Requirements:
 Must replace existing incandescent, PAR halogen or PAR halogen IR lamps for accent lighting, flood lighting or down
lighting in interior installations.
 Only less than or equal to 25 Watt, integrated ballast, Ceramic Metal Halide (CMH) PAR lamps with a rated lamp life
of 12,000 hours or greater
Additional Details:
 Customers are responsible for determining if new lamps will fit in their existing equipment and for verifying that the
new equipment works with the existing lighting controls
Table 22: Integrated Ballast Ceramic Metal Halide Par Lamps
Product code
Description
Rebate/Unit Measure
< 25 Integrated Ballast CMH PAR
Lamps
L-G21
$17.50/lamp
LED SURFACE, PENDANT AND RECESSED DOWN LIGHTING
Requirements:
 Only complete, new LED fixtures or retrofit kits qualify
 Must replace an existing Incandescent or Halogen lamp
 New fixture wattage must be less than existing fixture wattage
 New fixtures must be ENERGY STAR qualified (Visit www.energystar.gov for a list of qualified fixtures) or utility approved
 Exterior installations must be qualified by ENERGY STAR for exterior use and be listed in the ENERGY STAR qualified list
Exclusions:
 Existing CFL installations do not qualify
Additional Details:
 May qualify for an additional rebate through Occupancy Sensor or Photocell category provided all requirements are met
Table 23: LED Surface, Pendant, and Recessed Down Lighting
Product Code
L-U11
Existing Lamp Wattage
New Fixture Wattage
> 40 Watts
< 15 Watts
Rebate/Unit
$30.00/fixture
20
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
CONTROLS
WALL OR CEILING OCCUPANCY SENSOR
Self-Contained Wall-Switch (Wall-Box) Lighting Sensors – line voltage units that are designed to replace a standard wall
switch without additional switch/relay packs
Requirements:
 Only hardwired passive infrared and/or ultrasonic detectors that control interior lighting fixtures are eligible
 Must not exceed the maximum controlled wattage requirements listed in Table 24 below
Exclusions:
 Sensors for exterior installations do not qualify
Additional Details:
 New fixtures equipped with fixture-integrated sensors used in stairwells, halls, or garages sometimes qualify through
the Bi-level category and not the Occupancy Sensor category, depending on specifications
Table 24: Wall or Ceiling Occupancy Sensors
Product code
Description
Rebate/Unit Measure
L-J11*
Wall-Box Lighting Sensor
$20.00/sensor
L-J21
Wall or Ceiling Mounted Occupancy
Sensor < 500 Watts
$35.00/sensor
L-J31
Wall or Ceiling Mounted Occupancy
Sensor > 500 Watts
$55.00/sensor
*Product code L-J11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
FIXTURE INTEGRATED OCCUPANCY SENSORS
Fixture-Integrated Sensors – occupancy sensors that are factory or field-installed in a lighting fixture intended to
control the lamps within that fixture
Requirements:
 Only complete, new fixtures or retrofit kits qualify
 Only hardwired passive infrared and/or ultrasonic detectors that control interior lighting fixtures qualify
 Sensors must control all lamps in the fixture
 Must be inline with wattage controlled requirements listed in Table 25 below
 Must be compatible with installed ballast
Exclusions:
 Bi-level fixtures are not eligible for rebates under this category
 Effective January 1, 2011 sensors for exterior installations do not qualify
Additional Details:
 When used in conjunction with both T8 and T5 lamps: Program start ballasts are designed to provide maximum lamp
life in frequent lamp starting applications such as in areas where occupancy sensor controls are used
 When used in conjunction with T8 lamps: Instant-start electronic ballasts are the most popular type of electronic
ballast today because they provide maximum energy savings and start lamps without delay
Table 25: Fixture Integrated Occupancy Sensors
Product Code
Occupancy Sensor Type
Wattage controlled
Rebate/Unit
L-J41
Fixture-Integrated
> 150 Watts
$40.00/sensor
L-J51
Fixture-Integrated
< 150 Watts
$15.00/sensor
21
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
BI-LEVEL STAIRWELL/HALL/GARAGE FIXTURES
Bi-level Stairwell/Corridor Fixture – designed to reduce energy consumption while still providing appropriate
illumination levels during occupied periods and emergency egress. When spaces are unoccupied, the fixtures operate
at low light levels. Please see definition of garage on page 24.
Requirements:
 Only complete, new fluorescent fixtures with Programmed-Start electronic ballasts and lamps that meet
requirements in T8/T5 Lamp and Ballast category qualify
 Must be manufactured with fixture-body integrated occupancy sensors that that controls the individual fixture and
meet UL requirements
 All lamps must be pin-based fluorescent or other permanent installed technology (screw-in lamps are not eligible)
 Must include a passive infrared and/or ultrasonic occupancy sensor with a fail safe feature in case lamp fails due to
a sensor failure
 The fixture must operate in low-standby light level during vacancy and switch to full light output upon occupancy
 The fixture cannot exceed 35% of full wattage during unoccupied periods
Exclusions:
 Fixtures with settings that can be overridden are not eligible
 Not eligible for additional rebates through the Occupancy Sensor category or T8/T5 Lamp and Ballast category
Additional Details:
 Installation process: Low mode setting should be chosen so that the surface illuminate levels are code compliant
Table 26: Bi-level Stairwell/Hall/Garage Fixtures
Product Code
L-J61*
Description
Bi-level Stairwell/Hall/
Garage Fixtures
Rebate/Unit Measure
$25.00/fixture
*Product code L-J61 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
EXTERIOR PHOTOCELLS
Requirements:
 For built-in or stand-alone photoelectric cells that switch outdoor lights on at dusk and off at dawn
Table 27: Exterior Photocells
Product Code
L-K1*
Description
Exterior Photocells
Rebate/Unit Measure
$11.00/photocell
*Product code L-K1 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
TIME CLOCKS
Requirements:
 Must control on/off schedule of lighting equipment
 Can be used for interior and exterior lighting
 Must protect scheduled events from interruptions via 3-hour back up system during power outages
 Astronomical time clocks (where on-off times are in accordance with sunrise and sunset) are required for outdoor
lighting when a photocell is not in use
22
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 28: Time Clocks
Product Code
L-L1 1*
Description
Time Clocks
Rebate/Unit Measure
$36.00/time clock
*Product code L-L11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
SIGNAGE
HIGH-EFFICIENCY EXIT SIGNS
Electroluminescent Exit Sign – Exit sign using materials containing phosphors that light up when voltage is applied
Photoluminescent Exit Sign – Non-electrified exit sign containing materials that absorb and re-radiate light
Requirements:
 Only new LED, Electroluminescent, or Photoluminescent signs that replace those with
incandescent or Compact Fluorescent Lamps (CFL) qualify
 Must meet UL-924 requirements (listed on the product’s packaging)
 Must have a usage level that is less than or equal to 5 Watts
 Must have a product warranty of five (5) years
 Must meet local fire codes (Please check local fire codes)
Exclusions:
 Retrofit kits are not eligible
Table 29: High Efficiency Exit Signs
Product code
Description
Rebate/Unit Measure
L-M11*
Energy-Efficient Exit Sign
(Incandescent Basecase)
$27.00/fixture
L-M2*
Energy-Efficient Exit Sign
(CFL Basecase)
$15.00/fixture
*Product code (s) L-M11 and L-M2 are offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW)
through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
LED CHANNEL SIGNS
Requirements:
 Must replace incandescent-lighted or neon-lighted channel letter signs
 LED retrofit kits or complete LED replacement signs are eligible
 Replacement signs cannot use more than 20% of the actual input power of the sign that is replaced
Measure the length of the sign as follows:
1. Measure the length of each individual letter at the centerline. Do not measure the distance between letters
2. Add up the measurements of each individual letter to get the length of the entire sign being replaced
23
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
LIGHTING PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 30: Channel Signs (LED)
Product code
Description
Rebate/Unit Measure
L-N11
Indoor < 2ft. Retrofit
$4.00/foot
L-N21
Indoor < 2ft. Replacement
$4.00/foot
L-N31
Outdoor < 2ft. Retrofit
$2.00/foot
L-N41
Outdoor < 2ft. Replacement
$2.00/foot
L-N51
Indoor > 2ft. Retrofit
$6.00/foot
L-N61
Indoor > 2ft. Replacement
$6.00/foot
L-N71
Outdoor > 2ft. Retrofit
$3.00/foot
L-N81
Outdoor > 2ft. Replacement
$3.00/foot
DEFINITIONS
Bi-level Stairwell/Corridor Fixture - Designed to reduce energy consumption while still providing appropriate illumination levels during occupied periods and emergency egress. When spaces are unoccupied, the fixtures operate at low light
levels.
Candelabra Base - A smaller screw-in base for light bulbs with a 12 millimeter diameter, referred also as an E12 base.
De-lamping - The permanent removal of existing lamps, ballasts and unused lamp holders (tombstones) from existing
fixtures without replacing the lamps.
Edison Base - The most common screw-in base for light bulbs with a 26 millimeter diameter, referred also as an E26
(or medium) base.
Electroluminescent Exit Sign - Exit sign using materials containing phosphors that light up when voltage is applied.
ETL Listed Mark - A product bearing the ETL Listed Mark has been tested to be in compliance with applicable electric,
gas and other safety standards. For more information, visit www.etl.com.
Fixture - Refers to a new equipment being installed based on system (lamp and ballast) wattage.
Fixture-Integrated Sensors - Occupancy sensors that are factory or field-installed in a lighting fixture intended to
control the lamps within that fixture.
Garage - A parking garage is a covered building or structure for the purpose of parking vehicles, which consists of at
least a roof over the parking area enclosed with walls on all sides. Parking garages may have fences, rails, partial walls
(pony wall), or other barriers in place of one or more walls. The structure has an entrance(s) and exit(s), and includes
areas for vehicle maneuvering to reach the parking spaces. If the roof of the parking structure is also used for parking,
the section without an overhead roof is considered a parking lot instead of a parking garage.
High Performance T8 Lamp - High performance, T8 lamps are also known as 800 series. Typically the third generation
T8 lamps outperform 1st generation 700 series T8s in both lamp lumen output and longer lamp life.
Incandescent - Includes quartz Turglsen Halogen Lamps.
NEMA Premium Ballasts - Most efficient fluorescent fixed-output and dimmable electronics for T8 ballasts recognized
by the National Electronic Manufacturers Association (NEMA).
Photoluminescent Exit Sign - Non-electrified exit sign containing materials that absorb and reradiate light.
RoHS - Restriction of Hazardous Substances Directive
Self-Contained Wall-Switch (Wall-Box) Lighting Sensors - Line voltage units that are designed to replace a standard
wall switch without additional switch/relay pack.
Underwriters Laboratory (UL) - Is an independent product safety certification organization. For more information, visit
www.ul.com.
Wall or Ceiling Mounted Sensor - This sensor is generally installed to control multiple fixtures in a zone. It typically
requires a low-voltage switch and a relay pack, but may include line-voltage type sensor.
24
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: FOOD SERVICE PRODUCTS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial electric account if applying for an electric measure, and a gas account
if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of new or replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
 Customers must provide proof that the appliances meet the energy efficiency specifications
 For a list of qualifying products for the Food Service Equipment, visit www.fishnick.com
COMMERCIAL STEAM COOKER (ELECTRIC)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 31: Commercial Steam Cooker (Electric)
Product Code
FS-A11
Description
Steam Cooker (Electric)
Rebate/Unit Measure
$1250.00/steamer
COMMERCIAL STEAM COOKER (NATURAL GAS)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 32: Commercial Steam Cooker (Natural Gas)
Product Code
FS-A21
Description
Steam Cooker (Natural Gas)
Rebate/Unit Measure
$2000.00/steamer
INSULATED HOLDING CABINETS
Requirements:
 All measures must be electric hot food holding cabinets that are fully insulated and have solid doors in full,
three-quarter and half sizes respectively
 Qualifying cabinets must not exceed the maximum idle energy rate of 20 Watts/Ft3 in accordance with the
ASTM Standard F2140 test method
Exclusions:
 This measure does not include cook and hold equipment
Table 33: Insulated Holding Cabinets
Product Code
Description
Rebate/Unit Measure
FS-B1
Full Size – Energy rate < 0.4 kW
$300.00/unit
FS-B2
Three Quarter Size – Energy rate
< 0.3 kW
$250.00/unit
FS-B3
Half Size – Energy rate < 0.2 kW
$200.00/unit
25
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL FRYER (ELECTRIC)
Requirements:
 The commercial fryer must meet ENERGY STAR specifications for energy efficiency
Additional Details:
 Multiple vat configurations are paid per qualifying vat
Table 34: Commercial Fryer (Electric)
Product Code
FS-C1
Description
Commercial Electric Fryer
Rebate/Unit Measure
$200.00/vat
COMMERCIAL FRYER (NATURAL GAS)
Requirements:
 The commercial fryer must meet ENERGY STAR specifications for energy efficiency
Additional Details:
 Multiple vat configurations are paid per qualifying vat.
Table 35: Commercial Fryer (Natural Gas)
Product Code
FS-C2
Description
Commercial Gas Fryer
Rebate/Unit Measure
$500.00/vat
COMMERCIAL LARGE VAT FRYER (ELECTRIC)
Requirements:
 The commercial fryer must meet or exceed heavy load (French Fry) cooking energy efficiency of 80% utilizing
ASTM Standard F2144
Additional Details:
 Multiple vat configurations are paid per qualifying vat
Table 36: Commercial Large Vat Fryer (Electric)
Product Code
FS-C3
Description
Commercial Large Vat Electric
Fryer, Cooking Efficiency > 80%
Rebate/Unit Measure
$200.00/vat
COMMERCIAL LARGE VAT FRYER (NATURAL GAS)
Requirements:
 The commercial fryer must meet or exceed heavy load (French fry) cooking energy efficiency of 50% utilizing
ASTM Standard F2144
Additional Details:
 Multiple vat configurations are paid per qualifying vat
Table 37: Commercial Large Vat Fryer (Natural Gas)
Product Code
FS-C4
Description
Commercial Large Vat Gas Fryer,
Cooking Efficiency > 50%
Rebate/Unit Measure
$500.00/vat
26
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL ICE MACHINES
Requirements:
 This specification covers machines generating 60 grams (2oz.) or lighter ice cubes, as well as flaked, crushed and
fragmented ice
 Only air-cooled machines (self contained, ice making heads or remote condensing) are eligible
 The efficiency specifications for the two qualifying tiers are equivalent to ENERGY STAR or CEE Tier III
 To qualify the entire ARI tested ice making system must be purchased
 Remote machines must be purchased with qualifying remote condenser or remote condenser/compressor unit
 Ice machines must be tested in accordance with the Air Conditioning and Refrigeration Institute (ARI) Standard 810.
Visit www.ari.org for product information and testing procedures
Additional Details:
 Specifications are available at www.energystar.gov/cfs and www.Cee1.org
Table 38: Commercial Ice Machines
Product Code
FS-D8
FS-D9
FS-D10
FS-D11
FS-D12
FS-D13
FS-D14
FS-D15
FS-D16
FS-D17
FS-D18
FS-D19
FS-D20
FS-D21
Description (Ice Harvest
Rate Capacity )
ENERGY STAR Ice Machine
101-200 lbs/day
ENERGY STAR Ice Machine
201-300 lbs/day
ENERGY STAR Ice Machine
301-400 lbs/day
ENERGY STAR Ice Machine
401-500 lbs/day
ENERGY STAR Ice Machine
501-1,000 lbs/day
ENERGY STAR Ice Machine
1,001-1,500 lbs/day
ENERGY STAR Ice Machine
> 1,500 lbs/day
CEE Tier III Ice Machine
101-200 lbs/day
CEE Tier III Ice Machine
201-300 lbs/day
CEE Tier III Ice machine
301-400 lbs/day
CEE Tier III Ice machine
401-500 lbs/day
CEE Tier III Ice machine
501-1,000 lbs/day
CEE Tier III Ice machine
1,001-1,500 lbs/day
CEE Tier III Ice machine
> 1,500 lbs/day
Rebate/Unit
Measure
$50.00/unit
$50.00/unit
$75.00/unit
$75.00/unit
$125.00/unit
$200.00/unit
$250.00/unit
$100.00/unit
$100.00/unit
$150.00/unit
$150.00/unit
$250.00/unit
$400.00/unit
$500.00/unit
27
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL GRIDDLE (ELECTRIC)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 39: Commercial Griddle (Electric)
Product Code
FS-E1
Description
Rebate/Unit Measure
Commercial Electric Griddle
$300.00/griddle
COMMERCIAL GRIDDLE (NATURAL GAS)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 40: Commercial Griddle (Natural Gas)
Product Code
FS-E2
Description
Rebate/Unit Measure
Commercial Gas Griddle
$125.00/griddle
COMMERCIAL COMBINATION OVEN (ELECTRIC)
Requirements:
 The tested oven must meet or exceed heavy load cooking energy efficiency of 60% utilizing ASTM Standard F1639
Table 41: Commercial Combination Oven (Electric)
Product Code
FS-F1
Description
Rebate/Unit Measure
Commercial Electric Combination
Oven, Cooking Efficiency > 60%
$1,000.00/oven
COMMERCIAL COMBINATION OVEN (NATURAL GAS)
Requirements:
 The tested oven must meet or exceed heavy load cooking energy efficiency of 40% utilizing ASTM Standard F1639
Table 42: Commercial Combination Oven (Natural Gas)
Product Code
FS-F2
Description
Rebate/Unit Measure
Commercial Gas Combination
Oven, Cooking Efficiency > 40%
$750.00/oven
COMMERCIAL CONVECTION OVEN (ELECTRIC)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 43: Commercial Convection Oven (Electric)
Product Code
FS-G1
Description
Rebate/Unit Measure
Commercial Electric Convection
Oven
$350.00/oven
28
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL CONVECTION OVEN (NATURAL GAS)
Requirements:
 Must meet ENERGY STAR specifications for energy efficiency
Table 44: Commercial Convection Oven (Natural Gas)
Product Code
FS-G2
Description
Rebate/Unit Measure
Commercial Gas Convection Oven
$500.00/oven
COMMERCIAL SOLID DOOR REFRIGERATORS
Requirements:
 The refrigeration system shall be built-in (packaged)
 Must meet ENERGY STAR version 2.0 specifications for energy efficiency in table 45 below
Table 45: Maximum Daily Energy Consumption Requirements
Product Volume
(in cubic feet)
Refrigerator (Solid Door)
0 < V < 15 ft3
< 0.089V + 1.411 kWh day
15 < V < 30 ft3
< 0.037V + 2.200 kWh day
30 < V < 50 ft3
< 0.056V + 1.635 kWh day
50 < V ft3
< 0.060V + 1.416 kWh day
Exclusions:
 Cases with remote refrigeration systems do not qualify
 ENERGY STAR Specification Version 1.0 refrigerators do not qualify
Additional Details:
 V = Internal volume in Ft3 (cubic foot)
Table 46: Commercial Solid Door Refrigerators
Product Code
Description
Rebate/Unit Measure
FS-H11
ENERGY STAR Solid-Door
Reach-In Refrigerator < 15 ft3
$50.00/unit
FS-H21
ENERGY STAR Solid-Door
Reach-In Refrigerator 15-29 ft3
$75.00/unit
FS-H31
ENERGY STAR Solid-Door
Reach-In Refrigerator 30-49 ft3
$125.00/unit
FS-H41
ENERGY STAR Solid-Door
Reach-In Refrigerator 50ft3
and over
$200.00/unit
COMMERCIAL SOLID DOOR FREEZERS
Requirements:
 The refrigeration system shall be built-in (packaged)
 Must meet ENERGY STAR Specification Version 2.0. See Table 47 for specification summary
29
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 47: Maximum Daily Energy Consumption Requirements
Product Volume
(in cubic feet)
Freezer (Solid Door)
0 < V < 15 ft3
< 0.250V + 1.250 kWh day
15 < V < 30 ft3
< 0.400V – 1.000 kWh day
30 < V < 50 ft3
< 0.163V + 6.125 kWh day
50 < V ft3
< 0.158V + 6.333 kWh day
Exclusions:
 Cases with remote refrigeration systems do not qualify
 ENERGY STAR Specification Version 1.0 Freezers do not qualify
Additional Details:
 V = Internal volume in ft3 (cubic foot)
Table 48: Commercial Solid Door Freezers
Product Code
Description
Rebate/Unit Measure
FS-I11
Solid-Door Reach-In Freezer
< 15 feet3
$100.00/unit
FS-I21
Solid-Door Reach-In Freezer
15-29 feet3
$150.00/unit
FS-I31
Solid-Door Reach-In Freezer
30-49 feet3
$300.00/unit
FS-I41
Solid-Door Reach-In Freezer
50 feet3 and over
$600.00/unit
COMMERCIAL GLASS DOOR REFRIGERATORS
Requirements:
 The refrigeration system shall be built-in (packaged)
 Must meet ENERGY STAR Version 2.0 specification. Table 49 below shows a summary of the specifications
Table 49: Maximum Daily Energy Consumption Requirements
Product Volume
(in cubic feet)
Refrigerator (Glass Door)
0 < V < 15 ft3
< 0.118V + 1.382
15 < V < 30 ft3
< 0.140V + 1.050
30 < V < 50 ft3
< 0.088V + 2.625
50 < V ft3
< 0.110V + 1.500
Exclusions:
 Cases with remote refrigeration systems do not qualify
Additional Details:
 V = Internal volume in ft3 (cubic foot)
30
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 50: Commercial Glass Door Refrigerator
Product Code
FS-J51
Description
Rebate/Unit Measure
Glass-Door Reach-In Refrigerator
$75.00/unit
FS-J61
Glass-Door Reach-In Refrigerator
15-29 feet3
$100.00/unit
FS-J71
Glass-Door Reach-In Refrigerator
30-49 feet3
$125.00/unit
FS-J81
Glass-Door Reach-In Refrigerator
50 feet3 and over
$150.00/unit
< 15 feet3
COMMERCIAL GLASS DOOR FREEZER
Requirements:
 The refrigeration system shall be built-in (packaged)
 Must meet ENERGY STAR Version 2.0 specification. Table 51 below show a summary of the specifications
Table 51: Maximum Daily Energy Consumption Requirements
Product Volume
(in cubic feet)
Freezer (Glass Door)
0 < V < 15 ft3
< 0.607V + 0.893 kWh/day
15 < V < 30 ft3
< 0.733V - 1.000 kWh/day
30 < V < 50 ft3
< 0.250V + 13.500 kWh/Day
50 < V ft3
< 0.450V + 3.500 kWh/Day
Exclusions:
 Cases with remote refrigeration systems do not qualify
Additional Details:
 V = Internal volume in ft3 (cubic foot)
Table 52: Commercial Rack Oven (Natural Gas)
Product Code
Description
Glass-Door Reach-In Freezer < 15
FS-N11
FS-N21
Rebate/Unit Measure
feet3
Glass-Door Reach-In Freezer 15-29
$200.00/unit
feet3
$250.00/unit
feet3
$500.00/unit
FS-N31
Glass-Door Reach-In Freezer 30-49
FS-N41
Glass-Door Reach-In Freezer 50 feet3 and over
$1000.00/unit
COMMERCIAL RACK OVEN (NATURAL GAS)
Requirements:
 The tested commercial rack oven must meet or exceed baking energy efficiency of 50% utilizing
ASTM Standard F2093
Table 53: Commercial Rack Oven (Natural Gas)
Product Code
Description
Rebate/Unit Measure
FS-K1
Commercial Gas Rack Oven –
Single
$1,000.00/single oven
FS-K2
Commercial Gas Rack Oven –
Double
$2,000.00/double oven
31
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
FOOD SERVICE PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL CONVEYOR OVEN (NATURAL GAS)
Requirements:
 Must meet or exceed baking energy efficiency of 42% utilizing ASTM Standard F1817
 Small conveyor ovens with total conveyor width that is less than or equal to 25 inches must also have an idle energy
consumption rate that is less than or equal to 29,000 Btu/h
 Large conveyor ovens with total conveyor width that is greater than 25 inches must also have an idle energy
consumption rate that is less than or equal to 57,000 Btu/h.
Additional Details:
 Multiple-deck oven configurations are paid per qualifying oven deck
Table 54: Commercial Conveyor Oven (Natural Gas)
Product Code
Description
Rebate/Unit Measure
FS-L1
Commercial Conveyor Oven –
Small, < 25” Total Conveyor Width
$500.00/deck
FS-L2
Commercial Conveyor Oven –
Large, > 25” Total Conveyor Width
$750.00/deck
COMMERCIAL KITCHEN VENTILATION CONTROL
Requirements:
 This incentive applies towards the purchase and installation of a new commercial kitchen exhaust hood control
system installed in an existing or new dedicated commercial kitchen exhaust hood and make-up air system
 The control system must be used in conjunction with variable speed fan motor controls
 Only pre-approved control systems will qualify for an incentive
 Project Installation Worksheet must be submitted with the application. Worksheet available at www.fishnick.com
Table 55 : Commercial Kitchen Ventilation Control
Product Code
Description
Rebate/Unit Measure
FS-M1
Commercial Kitchen Ventilation
Control - Retrofit (Electric)
$350.00/fan hp
FS-M2
Commercial Kitchen Ventilation
Control - New Hood (Electric)
$300.00/fan hp
Definitions:
ASHRAE: The American Society of Heating, Refrigerating and Air-Conditioning Engineers
ASTM: American Society for Testing and Materials
CEE: Consortium for Energy Efficiency. CEE Tier specifications are available at www.cee1.org
ENERGY STAR: ENERGY STAR specifications are available at www.energystar.gov/cfs
32
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: REFRIGERATION PRODUCTS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial electric account if applying for an electric
measure, and a gas account if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of new or replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
 Customers must provide proof that the appliances meet the energy efficiency specifications
 Medium temperature refers to refrigerated space temperatures between 1°F and 35°F. Low temperature covers
temperatures below 0°F
NIGHT COVERS FOR MULTI-DECK AND HORIZONTAL DISPLAY CASES
Requirements:
 Must install a cover on an otherwise open display case to decrease cooling load of the refrigerated case during
off hours
 It is recommended that these film type covers have small, perforated holes to decrease moisture buildup
 The cover must be applied for a period of at least 6 hours in a 24-hour period
 Customer should consider the following: using proper compressor capacity modulation mechanisms (such as
Variable Speed Drive (VSD) or cylinder un-loader); using an Evaporator Pressure Regulator (EPR) and possibly
resetting to higher suction temperatures when shields are applied
 Case manufacturer must not have objections to the use of this measure
Additional Details:
 The rebate is based on linear footage of the installed night cover
Table 56: Night Covers for Multi-deck and Horizontal Display Cases
Product Code
Description
Rebate/Unit Measure
R-A11*
Night Covers for Multi-deck and
Horizontal Display Cases
(Medium Temp)
$3.50/linear foot
R-A21
Night Covers for Multi-deck and
Horizontal Display Cases
(Low Temp)
$3.50/linear foot
*Product code R-A11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through our
Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
STRIP CURTAINS FOR WALK-IN BOXES - Product closed effective March 31, 2011.
Requirements:
CLOSED
 Must install new strip curtains or plastic swinging doors on doorways of walk-in boxes and refrigerated warehouses
Exclusions:
 This rebate is not available for replacement of existing strip curtains that have useful life left (four years since date
of last purchase)
Additional Details:
 Rebate is based on the square footage of the doorway
33
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
CLOSED
Table 57: Strip Curtains for Walk-in Boxes
Product Code
R-B1
Description
Rebate/Unit Measure
Strip Curtains for Walk-in Boxes
$3.00/square foot
REFRIGERATION DISPLAY CASE WITH DOORS
Requirements:
 Must replace an existing open multi-deck display case with a new high efficiency reach-in unit with standard glass
doors with Electronically Commutated Motor (ECM) fan, T8 lamps and electronic ballast. (See Table 58 below)
 This measure can be applied to self-contained or remote cases
 New case length must be equal to or shorter than original case
Table 58: Existing and Replacement Equipment Requirements
Existing
Replacement
T-12 lamps, magnetic ballast
T8 lamps, electronic ballast
Shaded pole fan motor
ECM fan motor
Standard glass doors
Low/no anti-sweat glass double
pane doors meeting the requirements of R-C11 & R-C21
Exclusions:
 Deli cases, custom coolers/freezers and walk-in boxes with reach-in doors do not qualify
Additional Details:
 New display cases are rebated based on their length (Linear Footage)
Table 59: Refrigeration Display Case with Doors
Product Code
Description
Rebate/Unit Measure
R-C11
New Refrigeration Display Case
with Doors (Low Temp)
$175.00/linear foot
R-C21
New Refrigeration Display Case
with Doors (Medium Temp)
$75.00/linear foot
HIGH EFFICIENCY REFRIGERATION DISPLAY CASE WITH SPECIAL DOORS (LOW TEMP)
Requirements:
 The new high efficiency reach-in display case must replace an existing low temperature self-contained or remote
reach-in as shown in Table 60 below
Table 60: Existing and Replacement Equipment Requirements
Existing
Replacement
T-12 lamps, magnetic ballast
T8 lamps, electronic ballast
Shaded pole fan motor
ECM fan motor
Standard glass doors
Low/no anti-sweat glass double
pane doors meeting the requirements of R-C11 & R-C21
Exclusions:
 This measure cannot be used in conjunction with measure R-F11
34
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 61: High Efficiency Display Case with Special Doors (Low Temp)
Product Code
R-D11
Description
Rebate/Unit Measure
New High Eff. Refrigeration Display Case
with Special Doors (Low Temp)
$75.00/linear foot
SPECIAL DOORS WITH LOW/NO ANTI-SWEAT HEAT ON LOW TEMP DISPLAY CASES
Requirements:
 Must replace an existing standard glass door of a low temperature reach-in display case with a special glass door
that requires minimum to no anti-sweat heat (ASH)
 New Doors must prevent condensation from occurring within the frame assembly
Exclusions:
 Total door rail, glass, and frame heater amperage (at 120 volts) cannot exceed 0.39 amps per foot of display case
 This measure cannot be used in conjunction with measure R-F11
Additional Details:
 Rebate is based on number of doors replaced.
Table 62: Special Doors with Low/No ASH on Low Temp Display Cases
Product Code
R-E11
Description
Special Doors with Low/No Anti-Sweat
Heat on Low Temp Display Case
Rebate/Unit Measure
$100.00/door
ANTI-SWEAT HEAT (ASH) CONTROLS
Requirements:
 Must install a device that senses the relative humidity in the air outside of the display case and reduces or turns off
the glass door (if applicable) and frame anti-sweat heaters at low humidity conditions
 Equivalent technologies that can reduce or turn off anti-sweat heater based on the amount of condensation formed
on the inner glass pane may also qualify
Exclusions:
 This measure cannot be used in conjunction with Measures R-C11 and R-C21
Additional Details:
 Rebate is based on the total linear footage of the display case
Table 63: Anti-Sweat Heat (ASH) Controls
Product Code
R-F11*
Description
Anti-Sweat Heat (ASH) Controls
Rebate/Unit Measure
$25.00/linear foot
*Product code R-F11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
INSULATION FOR BARE SUCTION LINES
Requirements:
 Must insulate bare refrigeration suction lines of 1 5/8 inches in diameter or less on existing equipment only
 Medium temperature lines require 3/4-inch of flexible closed-cell nitrite rubber or equivalent insulation, and low
temperature lines require 1-inch of the same insulation
 Insulation exposed to outside weather must be jacketed (such as with a medium-gauge aluminum jacket) or
protected from the weather in some way
35
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Additional Details:
 Rebate is based on the length (linear feet) of the insulation installed
Table 64: Insulation for Bare Suction Lines
Product Code
R-G11*
Description
Insulation for Bare Suction Lines
Rebate/Unit Measure
$2.00/linear foot
*Product code R-G11 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
DOOR GASKETS ON REACH-IN DOORS
CLOSED
Requirements:
 Must replace a worn gasket on the insulated door of a reach-in cooler or freezer
 Replacement gaskets must meet the manufacturer’s installation specifications specifically regarding dimensions,
materials, attachment method, style, compression, and magnetism
Exclusions:
 This rebate is not available for replacement of existing gaskets that have useful life left (four years since date of
last purchase)
Additional Details:
 Rebate is based on total door perimeter in linear feet
Table 65: Door Gaskets on Reach – in Doors
Product Code
R-H11
Description
Door Gaskets on Reach-in Doors
Rebate/Unit Measure
$2.00/linear foot
DOOR GASKETS ON MAIN WALK-IN DOORS
CLOSED
Requirements:
 Must replace a worn gasket on the main insulated door of a walk-in cooler or freezer
 Replacement gaskets must meet the manufacturer’s installation specifications specifically regarding dimensions,
materials, attachment method, style, compression, and magnetism
Exclusions:
 This rebate is not available for replacement of existing gaskets that have useful life left (four years since date of
last purchase)
Additional Details:
 Rebate is based on total door perimeter in linear feet
Table 66: Door Gaskets on Main Walk-in Doors
Product Code
R-I11
Description
Door Gaskets on Main Walk-in
Doors
Rebate/Unit Measure
$2.00/linear foot
36
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
AUTO CLOSERS FOR WALK-IN COOLER OR MAIN FREEZER DOORS
Requirements:
 The auto-closer should be applied to the main insulated door of a walk-in cooler or freezer
 The auto-closer must be able to firmly close that door when it is within one inch of full closure
Table 67: Auto-Closers for Walk-in Cooler or Main Freezer Doors
Product Code
Description
Rebate/Unit Measure
R-J11*
Auto-Closers for Main Cooler
Doors
$75.00/closer
R-J21*
Auto-Closers for Main Freezer
Doors
$75.00/closer
*Product code(s) R-J11 and R-J21 are offered at no cost for customers with monthly electrical demand under 100 kilowatts
(kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at
1-800-644-6133
EVAPORATOR FAN CONTROLLER FOR WALK-IN COOLERS AND FREEZERS
Requirements:
 Must reduce airflow of evaporator fans in medium-temperature walk-in coolers and freezers when compressor(s)
cycle off and there is no refrigerant flow through the evaporator
 Must control a minimum fan load of 1/20 horsepower where the fan(s) operate continuously at full speed
 Must reduce fan motor power by at least 75% when the compressor off-cycle
Exclusions:
Do not install if any of the following conditions apply:
1)
The compressor runs all the time with high duty cycle
2) The evaporator fan does not run at full speed all the time
3) The evaporator fan motor runs on poly-phase power
4) The evaporator fan motor is not shaded-pole
5) Evaporator does not use off-cycle or time-off defrost
Table 68: Evaporator Fan Controller for Walk-in Coolers and Freezers
Product Code
Description
Rebate/Unit Measure
R-K1
Evaporator Fan Controller for
Walk-In Coolers
$75.00/controller
R-K2
Evaporator Fan Controller for
Walk-In Freezers
$75.00/controller
EFFICIENT EVAPORATOR FAN MOTOR
Requirements:
 Applicable to existing standard efficiency shaded pole evaporator fan motor of refrigerated display cases or fan
motors in walk-in coolers
 Shaded pole motors to be replaced by either Electronically Commutated Motors (ECM) or permanent-split-capacitor
(PSC) motors
Exclusions:
 This measure cannot be used in conjunction with measure R-K1 and R-K2
37
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
REFRIGERATION PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 69: Efficient Evaporator Fan Motor
Product Code
Description
Rebate/Unit Measure
R-L11*
Electronically Commutated Motor
(ECM) For display cases fan
$35.00/motor
R-L21
Efficient Evaporator Fan Motor –
Permanent Split Capacitor (PSC)
Motor
$50.00/motor
R-L31*
Electronically Commutated Motor
(ECM) for Walk-In Fan
$50.00/motor
*Product code(s) R-L11 and R-L31 are offered at no cost for customers with monthly electrical demand under 100
kilowatts (kW) through our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings
Center at 1-800-644-6133
38
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: NATURAL GAS PRODUCTS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial gas account if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of new or replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
 If you are uncertain whether equipment qualifies, contact a utility representative. The California Energy Commission
(CEC) and/or Air-Conditioning Heating and Refrigeration Institute (AHRI) equipment efficiency listed ratings prevail
over all submitted technical documentation, unless otherwise approved
STORAGE WATER HEATER
Requirements:
 Water heaters must meet efficiency requirements based on size, as shown in Table 70 below
Table 70: Storage Water Heater Efficiency Requirements
Input Rating
Required Efficiency
< 75,000 Btuh
Energy Factor > 67%
> 75,000 Btuh
Thermal Efficiency > 84%
Exclusions:
 Equipment used for pools and spas does not qualify
Additional Details:
 If the size and efficiency are not shown on the invoice, you must include a manufacturer’s specification sheet
documenting these characteristics
Table 71: Storage Water Heater
Product Code
G-A1
Description
Rebate/Unit Measure
Storage Water Heater
$2.00/mbtuh
SPACE HEATING BOILER
Requirements:
 Boilers must meet efficiency requirements based on size and type as shown in Table 72 below
 Include a manufacturer’s specification sheet documenting these characteristics
 Boiler must be used for space heating for human comfort as defined by California Titles 20 & 24 standards
 Must use a licensed contractor, as appropriate, and follow applicable permitting requirements for this installation.
Required to confirm compliance by placing a check mark in the corresponding box in Section 7 of the
Energy Efficiency Business Rebates Application.
Exclusions:
 Equipment used for pools and spas does not qualify
Table 72: Space Heating Boiler
Product Code
Type
Required
Efficiency
Input Rating
Rebate/Unit Meaure
G-B1
Steam
< 300 MBtuh
AFUE > 77%
$0.25/mbtuh
G-B2
Small Water
< 300 MBtuh
AFUE > 82%
$0.25/mbtuh
G-B3
Large
> 300 MBtuh - < 5,000 MBtuh
Thermal Efficiency > 84%
$0.25/mbtuh
39
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
COMMERCIAL BOILER (NON SPACE CONDITIONING/NON-PROCESS RELATED)
Requirements:
 Only boilers > 75,000 Btuh qualify
 Must meet a minimum thermal efficiency of 84%
Exclusions:
 Boiler must not be used for space conditioning for human comfort
 Boiler must not be used for industrial (process) end-use
 Equipment used for pools and spas does not qualify
 Industrial customers do not qualify
Additional Details:
 Include a manufacturer’s specification sheet documenting these characteristics
Table 73: Commercial Boiler (Non-Space Conditioning/Non-Process Related)
Product Code
G-C1
Description
Commercial Boiler
Rebate/Unit Measure
$0.50/mbtuh
INSTANTANEOUS (TANKLESS) WATER HEATER
Requirements:
 Water heaters must meet efficiency requirements based on size shown in Table 74
 Only instantaneous water heaters (as defined by the California Energy Commission Title 20 & 24 standards) used for
non-process hot water applications qualifies
 The manufacturer name and equipment model number must be provided
 Customers must provide proof of the tankless nature of the water heater (e.g., manufacturer equipment
specification sheets)
Table 74: Instantaneous (Tankless) Water Heater
Product Code
Description
Technical & Size
Requirements
Rebate/Unit Meaure
G-D1
Small Instantaneous
Hot Water Heater
< 200 MBtuh
Energy Factor > 63%
$2.00/mbtuh
G-D2
Large Instantaneous
Hot Water Heater
> 200 MBtuh
Thermal Efficiency > 82%
$0.50/mbtuh
PROCESS BOILER
Manufacturing - involves the mechanical or chemical transformation of materials or substances into a new product
which is neither a structure nor any other fixed improvement.
Requirements:
 Available to industrial end-use customers who manufacture a sellable product only (NAICS codes 31-33)
 Boilers must meet a minimum combustion efficiency of 82% as installed
 Only process boilers qualify
Additional Details:
 The manufacturer name and equipment model number must be provided
 A flue gas analysis measured under full load conditions is required to document combustion efficiency after
installation is complete
40
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Exclusions:
 Boilers primarily used for domestic hot water, space conditioning, pool or spa use do not qualify
Table 75: Process Boiler
Product Code
Description
Technical Requirements
Rebate/Unit Measure
G-E1
Steam Process Boiler
Combustion Efficiency > 82%
$0.50/mbtuh
G-E2
Water Process Boiler
Combustion Efficiency > 82%
$0.50/mbtuh
COMMERCIAL POOL OR SPA HEATER
Requirements:
 Must replace existing pool or spa heater
 Must be certified to meet the following requirements:

Heater must be equal to or greater than 84% thermal efficiency

Equipment must have an “on/off” switch and have no pilot light

Refer to: http://www.energy.ca.gov/appliances/database for a list of qualifying products
Table 76: Commercial Pool or Spa Heater
Product Code
G-F1
Description
Commercial Pool or Spa Heater
Rebate/Unit Measure
$2.00/mbtuh
DIRECT CONTACT WATER HEATER
In direct contact water heater system designs, heat from a flame comes into direct contact with small droplets of cold
water which run through a stainless steel heat exchange media
Requirements:
 Only direct contact water heaters for process end-uses qualify (NAICS codes 31-33)
 Boilers must meet efficiency requirements as shown in Table 77 below
Exclusion:
 Water heater primarily used for domestic hot water, space conditioning, pool or spa use do not qualify
Table 77: Direct Contact Water Heater
Product Code
G-G1
Required Efficiency
> 300 MBtuh - >90% Thermal
Rebate/Unit Measure
$2.00/mbtuh
Efficiency
G-G2
< 300 MBtuh - >88% AFUE
$2.00/mbtuh
PIPE INSULATION (NON-SPACE CONDITIONING)
Requirements:
 1” or 2” of fiberglass, foam, or calcium silicate insulation must be added to existing nonresidential bare pipe systems
which transfer fluid directly from gas-fired equipment
 The bare pipe diameter must be at least 1/2 inch
 Minimum insulation must be 1” to qualify
Exclusions:
 New construction application does not qualify
 New pipe system replacement does not qualify
 Fuel switching application does not qualify
 Residential application does not qualify
41
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Additional Details:
 Must submit manufacturer’s name and insulation material type
 Customer must also provide proof of insulating values (e.g. Manufacturer’s specification sheets)
Table 78: Pipe Insulation (Non-Space Conditioning)
Product Code
Description & Technical Requirements
Rebate/Unit Measure
G-H11
Pipe diameter < 1”; Low pressure (< 15 psi) Steam
$3.00/linear foot
G-H21
Pipe diameter > 1”; Low pressure (< 15 psi) Steam
$3.00/linear foot
G-H31*
Pipe diameter < 1”; Hot Water
$2.00/linear foot
G-H41
Pipe diameter > 1”; Hot Water
$2.00/linear foot
G-H51
Pipe diameter < 1”; Medium pressure (> 15 psi) Steam
$3.00/linear foot
G-H61
Pipe diameter > 1”; Medium pressure (> 15 psi) Steam
$3.00/linear foot
G-H71
Pipe diameter > 1”; High pressure (> 15 psi) - Steam
(FOR DRY CLEANER APPLICATION USE ONLY NAICS
code: 812320)
$3.00/linear foot
*Product code G-H31 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through our
Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
TANK INSULATION
High temperature application: 170 – 200 degrees F solution
Low temperature application: 120 – 170 degrees F solution
Requirements:
 1” or 2” of fiber glass or foam insulation must be added to existing bare liquid or solution storage or transfer tanks
 Tanks must be coupled to gas-fired commercial or industrial equipment that transfers heat to the liquid or solution
 Customers must also provide the manufacturer’s name and insulation material type
Additional Details:
 The insulation thickness and tank solution temperature will determine the rebate amount
Table 79: Tank Insulation
Product Code
Description & Technical
Requirements
Rebate/Unit Measure
G-I1
Tank insulation High Temperature
Applic. 1 in thick
$3.00/square foot
G-I2
Tank insulation High Temperature
Applic. 2 in thick
$4.00/square foot
G-I3
Tank insulation Low Temperature
Applic. 1 in thick
$2.00/square footf
G-I4
Tank insulation Low Temperature
Applic. 2 in thick
$3.00/square foot
RESIDENTIAL HIGH EFFICIENCY CLOTHES-WASHER
Modified Energy Factor (MEF) - measures energy consumption of the total laundry cycle (washing and drying). It
indicates how many cubic feet of laundry can be washed and dried with one kWh of electricity; the higher the number,
the greater the efficiency.
Water Factor (WF) - represents the number of gallons of water needed for each cubic foot of laundry. The lower number
indicates lower consumption and more efficient use of water.
Requirements:
 Rebate is for a high-efficiency residential washer used at a business for onsite/in-house laundry
42
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
 Must have either natural gas or electricity distributed to the installation address by SDG&E
 Qualifying clothes washers must have specific Modified Energy Factors (MEF) and Water Factors (WF) based on
levels listed below
 Qualifying Level 1 residential clothes washers may be viewed at
http://www.cee1.org/resid/seha/rwsh/rwsh-prod.pdf, Tier 2 and 3A
 Qualifying Level 2 residential clothes washers may be viewed at
http://www.cee1.org/resid/seha/rwsh/rwsh-prod.pdf, Tier 3B
Exclusions:
 Commercial coin operated equipment does not qualify
Table 80: Residential High Efficiency Clothes Washer
Description & Technical
Requirements
Product Code
Rebate/Unit Measure
G-J1
High-Efficiency Clothes Washer, CEE Tier 2
and 3A models only MEF of 2.0 or greater
and a WF of 6.0 or less
$35.00/unit
G-J2
High-Efficiency Clothes Washer, CEE Tier 3B
models only MEF of 2.2 or greater and a WF
of 4.5 or less
$75.00/unit
STEAM TRAPS
Requirements:
 Must be an Industrial customer that manufactures a saleable product (NAICS 31-33) or a commercial facility that
operates 12 hrs or more
 Steam traps must replace one-to-one an existing failed or older steam traps that have been in service for a minimum
of five years
 For each steam trap being replaced customer must provide steam trap manufacturer, model number, specification
sheet, paid purchase receipt with tax and proof of shipping
 Customer must provide operating pressure of steam system, and construction style (mechanical, thermostatic, or
thermodynamic)
 Customer may be asked to verify the location of the replaced steam trap(s) in steam loop
Exclusions:
 New construction is not eligible
Table 81: Steam Traps
Product Code
Required Efficiency
Rebate/Unit Measure
G-M1
Commercial customer operating
steam system < 12 hrs a day,
dry cleaners excluded
$100.00/unit
G-M2
Industrial customer operating
steam system < 15 psig
Commercial customer operating
steam system 12-24 hrs a day
$100.00/unit
Industrial customers with systems
operating at > 15 psig
$200.00/unit
G-M3
CLOSED
43
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
NATURAL GAS PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
OZONE LAUNDRY SYSTEM – Purchased & Installed on or after 2/17/2012
Requirements:
 Customer must have a natural gas-fired boiler or natural gas water heater that supplies hot water to the on-premise
laundry equipment.
 This incentive only applies to hotels/motels with fewer than 250 guest rooms OR fitness and recreational sports
centers that have on-premise laundry operations.
 The ozone laundry system(s) must be a new purchased product and added-on to a new or existing commercial
washing machine(s).
 The ozone laundry system(s) must transfer ozone into the water through Venturi Injection OR Bubble Diffusion.
 For hotel customers: The total number of guest rooms must be provided on the invoice.
 Include a manufacturer’s specification sheet documenting manufacturer name, equipment model, and ozone
laundry system’s serial number(s).
 Must provide total washer capacity in pounds for operating washer units with ozone laundry system(s) connected.
Additional Details:
 Hotels/motels with 250 guest rooms or more and other types of facilities may be considered under our Energy
Efficiency Business Incentives.
Table 82: Ozone Laundry System
Product Code
G-N11
Description
Ozone Laundry System
Rebate/Unit Measure
$39.00/lb
Washing Machine Capacity
(Connected to Ozone
Laundry System)
Definitions:
Annual Fuel Utilization Efficiency (AFUE): the ratio of annual output energy to annual input energy
Bubble Diffusion: A method of inserting ozone into water by continuously bubbling ozone directly
into the sump of the washerthroughout the wash cycle.
Combustion Efficiency (CE): 100 times (1 - energy lost to flue) divided by input energy
MBtuh: 1,000 Btuh
Thermal Efficiency (TE): 100 times useful energy output divided by input energy
Total Washer Capacity: Refers to rated capacity of installed and operating washing machine units that
will be connected to the ozone laundry system(s).
Venturi Injection: A method of inserting ozone into water using very high pressure directly into the
cold water supply line leading to the washer.
44
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
AGRICULTURAL PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: AGRICULTURAL PRODUCTS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial electric account if applying for an electric measure, and a gas account
if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of new or replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
SPRINKLER TO DRIP IRRIGATION
Requirements:
 Must convert from a high-pressure, impact-type, sprinkler irrigation system (50 psi operating pressure or more at
the sprinkler head) to a micro-irrigation system.
 Drip tape systems are not eligible. Include an Assessor’s Parcel Map or other documentation to verify acreage
Exclusions:
 Not applicable to new plantings of vineyards or orchards unless a vineyard or orchard was the previous crop on
the field
Table 83: Sprinkler to Drip Irrigation
Product Code
O-C1
Description
Sprinkler to Drip Irrigation
Rebate/Unit Measure
$44.00/acre
LOW PRESSURE SPRINKLER NOZZLES
Requirements:
 Must convert from a high-pressure, sprinkler system nozzle (50 psi operating pressure or more at the sprinkler
head)
 Must be accompanied by a pumping plant analysis to ensure reasonable pumping efficiency (45% Overall Pumping
Efficiency or above) after the conversion
 Portable hand move or solid set systems may apply
Table 84: Low Pressure Sprinkler Nozzles
Product Code
O-D1
Required Efficiency
Low Pressure Sprinkler Nozzles
Rebate/Unit Measure
$1.15/nozzle
GREENHOUSE HEAT CURTAINS
Requirements:
 Pre-inspection required, to schedule pre-inspection contact our Energy Information Center at 1-800-644-6133
 Only installations of interior curtains for heat retention in existing gas-heated greenhouses qualify
 The rebate applies to new and retrofit curtain system installations in existing greenhouses for specific
agricultural end-use
 The agricultural uses include horticultural specialties such as ornamental floriculture, nursery products and food
crops grown under cover (NAICS 1114) and landscape and horticultural services (NAICS 541 & 561) which store
agricultural products under cover
 Product must be designed by the manufacturer to be a heat curtain, and the installation must have the ability to
automatically or manually move the curtain into place
45
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
AGRICULTURAL PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
 Curtain must be located such that the gas heat source provides hot air to conditioned space bounded by the curtain
 Curtain material must have an Energy Savings rating of greater than 40% and must have a warranty/product life of
5 years
 Rebate amount is for square footage of curtain material
 Application must include the manufacturer’s specification sheet documenting type of curtain
 Rebate amount cannot exceed square feet of qualifying curtain material purchased, paid for and properly installed
at SDG&E account listed on the rebate form
 Rebate amount also cannot exceed the square feet of floor space covered by the installation of the curtain material
 Must provide greenhouse square footage in the table provided in Section 5 (Additional Information) of the Energy
Efficiency Business Rebates Application
Exclusions:
 Overhang and overlap of curtain material does not qualify for rebate
Table 85: Greenhouse Heat Curtains
Product Code
G-K1
Required Efficiency
Rebate/Unit Measure
Greenhouse Heat Curtains
$0.20/square foot
INFRARED FILM FOR GREENHOUSES
Requirements:
 Installations of single sheet infrared anti-condensate polyethylene plastic with a minimum 6 mil. thickness for heat
retention on existing heated greenhouses will qualify
 Greenhouses must be for agriculture and floriculture uses (NAICS 1114), as well as landscape and horticultural
services (NAICS 541 & 561)
 A manufacturer’s specification sheet must be included
Table 86: Infrared Film for Greenhouses
Product Code
G-L1
Required Efficiency
Rebate/Unit Measure
Infrared Film for Greenhouses
$0.05/square foot
CLOSED
WINE TANK INSULATION — Product closed December 31, 2011
Requirements:
 Must have an insulation value equal to or greater than R-12 and be added to an existing refrigerated wine tank
 Customers must provide the manufacturer’s name, and the R-value rating
Table 87: Wine Tank Insulation
Product Code
Description & Technical
Requirements
Rebate/Unit Measure
O-G1
Wine Tank insulation - Indoor
tank
$2.25/square foot
O-G2
Wine Tank insulation - Outdoor
tank- Coastal
$3.00/square foot
O-G3
Wine Tank insulation - Outdoor
tank - Inland
$3.75/square foot
46
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
MOTORS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: MOTORS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial electric account if applying for an electric measure, and an SDG&E gas
account if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
PREMIUM EFFICIENCY MOTORS
Requirements:
 Only new motor installations qualify
 Only three-phase motors intended for commercial, industrial and /or agricultural sectors qualify
 Motors must meet minimum efficiency requirement shown in Table 88 below. Specifications are also available at
www.Cee1.org.
 Motors must be classified as either three phase induction motors of open drip proof (ODP) or totally enclosed fan
cooled (TEFC)
 Customer must provide motor manufacturer, model number, and specification sheet
 Motors must be between 1 and 200 horsepower
Exclusions:
 Used or rebuilt Motors are not eligible
(section continues on following page)
47
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
MOTORS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Table 88: CEE Premium Efficiency Motors Specifications
Open Drip Proof (ODP)
Motor Size HP
1800 RPM
1200 RPM
77
85.5
82.5
1.5
84
86.5
2
85.5
86.5
1
3600 RPM
Totally Enclosed Fan Cooled (TEFC)
3600 RPM
1800 RPM
1200 RPM
77
85.5
82.5
86.5
84
86.5
87.5
87.5
85.5
86.5
88.5
3
85.5
89.5
88.5
86.5
89.5
89.5
5
86.5
89.5
89.5
88.5
89.5
89.5
7.5
88.5
91
90.2
89.5
91.7
91
10
89.5
91.7
91.7
90.2
91.7
91
15
90.2
93
91.7
91
92.4
91.7
20
91
93
92.4
91
93
91.7
25
91.7
93.6
93
91.7
93.6
93
30
91.7
94.1
93.6
91.7
93.6
93
40
92.4
94.1
94.1
92.4
94.1
94.1
50
93
94.5
94.1
93
94.5
94.1
60
93.6
95
94.5
93.6
95
94.5
75
93.6
95
94.5
93.6
95.4
94.5
100
93.6
95.4
95
94.1
95.4
95
125
94.1
95.4
95
95
95.4
95
150
94.1
95.8
95.4
95
95.8
95.8
200
95
95.8
95.4
95.4
96.2
95.8
Table 89: Premium Efficiency Motors
Product Code
Description
Rebate/Unit Measure
M-A1
Motors 1 HP
$35.00/motor
M-A2
Motors 1.5 HP
$35.00/motor
M-A3
Motors 2 HP
$35.00/motor
M-A4
Motors 3 HP
$40.00/motor
M-A5
Motors 5 HP
$50.00/motor
M-A6
Motors 7.5 HP
$60.00/motor
M-A7
Motors 10 HP
$70.00/motor
M-A8
Motors 15 HP
$80.00/motor
M-A9
Motors 20 HP
$90.00/motor
M-A10
Motors 25 HP
$135.00/motor
M-A11
Motors 30 HP
$230.00/motor
M-A12
Motors 40 HP
$300.00/motor
M-A13
Motors 50 HP
$320.00/motor
M-A14
Motors 60 HP
$355.00/motor
M-A15
Motors 75 HP
$540.00/motor
M-A16
Motors 100 HP
$720.00/motor
M-A17
Motors 125 HP
$945.00/motor
M-A18
Motors 150 HP
$1,260.00/motor
M-A19
Motors 200 HP
$1,260.00/motor
48
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
OTHER TECHNOLOGY PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
TERMS AND CONDITIONS: OTHER TECHNOLOGY PRODUCTS
GENERAL REQUIREMENTS
 Customers must have a SDG&E commercial electric account if applying for an electric measure, and an SDG&E gas
account if applying for a gas measure
 Everything must be installed and operational before a rebate application is submitted
 All rebates apply toward the purchase of new or replacement energy-efficient equipment, unless otherwise
indicated. Used or rebuilt equipment is not eligible
REFLECTIVE WINDOW FILM
To convert Shading Coefficient (SC) to Solar Heat Gain Coefficient (SHGC), use the following equation: SHGC = SC x .87
Requirements:
 Film must have a minimum 5-year manufacturer’s warranty
 Space must be cooled by vapor-compression air conditioner (evaporative-cooled space not eligible)
 Must be applied to clear, single-pane glass and meet one of the following:

Film must have a SHGC less than 0.39

Or film can have a SHGC less than 0.47 and visible transmittance/solar heat gain coefficient (VT/SHGC) ratio
greater than 1.3
 Specification and square footage installed must be documented on the invoice
Exclusions:
 Rebates are not available for windows with northern exposure (+ 45 degrees of due North)
 Dual-pane glass does not qualify for this rebate
Table 90: Reflective Window Film
Product Code
Required Efficiency
Rebate/Unit Measure
O-A1
Reflective Window Film (Coastal)
$1.35/square foot
O-A2
Reflective Window Film (Inland)
$1.35/square foot
O-A3
Reflective window Film (Desert)
$1.35/square foot
PLUG LOAD OCCUPANCY SENSOR
Requirements:
 Only passive infrared and/or ultrasonic detectors are eligible
 “Plug load” occupancy sensors must control electric equipment in offices or cubicles, or control shared
copiers and/or printers
 Plug load sensors must control a minimum of 50 watts to qualify
Table 91: Plug Load Occupancy Sensors
Product Code
SD-A1
Required Efficiency
Plug Load Occupancy Sensor
Rebate/Unit Measure
$15.00/sensor
49
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
OTHER TECHNOLOGY PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
LOW-FLOW SHOWERHEAD
Requirements:
 Must replace a standard showerhead and have a flow stream of 2.0 gallons per minute (gpm) or less at 80 pounds
per square inch (psi)
Table 92: Low-Flow Showerhead
Product Code
SD-B1*
Required Efficiency
Rebate/Unit Measure
Low-Flow Showerhead
$20.00/showerhead
*Product code SD-B1 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
NETWORK POWER MANAGEMENT SOFTWARE
Requirements:
 Software must be installed that automatically controls the power settings of networked personal computers (PC)
at the server level
 The software must be capable of managing power consumption for each individual PC
 In addition, the software must be capable of reporting energy saving results
 Customers must provide:
• A copy of the software license agreement
• A report directly from the Network Energy Management software that verifies the number of PCs that are being
controlled by the system
• A list of license numbers serving the system
Exclusions:
 Computer laptops are not eligible
Table 93: Network Power Management Software
Product Code
SD-C1
Required Efficiency
Rebate/Unit Measure
Network Power Management
Software
$15.00/desktop computer
HIGH EFFICIENCY COPIER
Requirements:
 Copier must be used in offices or cubicles, listed as ENERGY STAR qualified and replace a copier without an
idle/off control
Exclusions:
 Desktop copiers are not eligible
Table 94: High Efficiency Copier
Product Code
SD-D1
Required Efficiency
Rebate/Unit Measure
High Efficiency Copier
$100.00/unit
EARLY RETIREMENT REFRIGERATOR
Requirements:
 Units must be ENERGY STAR compliant and a minimum of 14 cubic feet
 The new residential sized refrigerators must replace working refrigerators of at least 14 cubic feet
 Old, replaced refrigerators must be recycled. Cannot recycle using a program funded by the Public Goods Charge (i.e. ARCA)
 A recycling certification must be included with the invoice and can be found on the website: sdge.com/businessrebates
50
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
TERMS AND CONDITIONS
OTHER TECHNOLOGY PRODUCTS
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Additional Details:
 Compliant refrigerators can be found on the ENERGY STAR website at:
http://www.energystar.gov/refrigerators
Table 95: Early Retirement Refrigerator
Product Code
SD-E1
Required Efficiency
Early Retirement - Refrigerator
Rebate/Unit Measure
$275.00/unit
VENDING MACHINE CONTROLLER
Requirements:
 Intended for refrigerated vending machines containing only non-perishable bottled and canned beverages
 Controller must include a passive infrared occupancy sensor to turn off fluorescent light and compressor when
surrounding area is unoccupied for 15 minutes or longer
 Control logic should periodically power up machine at two-hour intervals to maintain product temperature and
provide compressor protection
 Refurbished vending machines that include this option are eligible
Table 96: Vending Machine Controller
Product Code
R-O1*
Required Efficiency
Vending Machine Controller
Rebate/Unit Measure
$100.00/controller
*Product code R-O1 is offered at no cost for customers with monthly electrical demand under 100 kilowatts (kW) through
our Direct Install Program. For details visit sdge.com/directinstall or call our Energy Savings Center at 1-800-644-6133
VARIABLE FREQUENCY DRIVES (VFD’S)
Requirements:
 VFD incentives are for fan applications on HVAC systems
 The maximum fan size is 100 hp
 The installation of a VFD on a HVAC fan is eligible for a rebate only if throttling devices, such as inlet vanes, bypass
dampers and throttling valves, are removed or permanently disabled
Additional Details:
 A 3% impedance choke is recommended
Table 97: Variable Frequency Drives (VFD’s)
Product Code
O-B1
Required Efficiency
Variable Frequency Drives (VFDs)
Rebate/Unit Measure
$80.00/hp
The selection, purchase, and ownership of goods and services are the sole responsibility of the customer. SDG&E makes no representations as to
the safety, reliability, and/or efficiency of goods and services selected. SDG&E makes no warranty, whether express or implied, including warranty of
merchantability or fitness for any particular purpose, use or application of selected goods and services. The program is funded by California utility
customers and administered by SDG&E under the auspices of the California Public Utilities Commission (CPUC). Program funds will be made on a firstcome, first-served basis until program funds are no longer available. This program may be modified or terminated without prior notice. The selection,
purchase and ownership of goods and services are the sole responsibility of the customer.
The web site links contained herein are provided for information purposes only. SDG&E does not endorse these web sites, or any goods or services offered thereon. Particularly, SDG&E has not verified the privacy policies applicable to these web sites, or determined what actions will be taken by third
parties regarding the privacy of visitors. In no event shall SDG&E be responsible for any third party web site policies or actions.
P.O. Box 129831 | San Diego, CA 92112-9831 | 1-800-411-7343 | Connect at sdge.com
51
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
Energy Efficiency Business Rebates
Product Catalog
Index
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product Description (Alphabetical)
Page(s)
Accent/Directional Lighting
20
Anti-Sweat Heat Controls
35
Auto-Closers
37
Bi-Level Stairwell/Hall/Garage Fixtures
22
39-41
Boilers and Water Heaters
Ceramic Metal Halide Fixtures
12
Ceramic Metal Halide PAR Lamps
20
Channel Signs (LED)
23-24
Clothes-Washers
42-43
Cold Cathode Lamps
16
Compact Fluorescent Fixtures
9-10
Compact Fluorescent Lamps
16-17
Controls (Anti-Sweat Heat)
35
Controls (Kitchen Ventilation)
32
Controls (Lighting)
21-23
Copier (High Efficiency)
49
Directional/Accent Lighting
20
Display Case LED Lighting
15
Display Case Refrigeration Doors
33-35
Door Gaskets Product closed September 30, 2010
36
Evaporator Fan Motors
37-38
Evaporator Fans Controllers
37
Exit Signs
23
29-30
Freezer
Fryers
26
Greenhouse Heat Curtains
45-46
Griddles
28
Ice Machines
27
Induction Fixtures
10-11
Infrared Film for Greenhouses
46
Insulated Holding Cabinets
25
Insulation for Bare Suction Lines
35-36
Insulation (Pipes)
41-42
Insulation (Tank)
42
Insulation (Wine Tank) — Product closed December 31, 2011
46
Kitchen Ventilation Controls
32
52
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912
PRODUCT CATALOG
INDEX
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
Product Description (Alphabetical)
LED Display Case Lighting
Page(s)
15
LED Fixtures
13-16
LED Integral Lamps
19-20
LED Refrigerated Case Lighting
15-16
LED Surface, Pendant, and Recessed Down Lighting
20
Lighting Controls
21-23
Linear Fluorescent Fixtures
11-12
Linear Fluorescent Lamp Removal (T12)
17-18
Linear Fluorescent Lamp Removal (T8)
18
Linear Fluorescent Lamps (T8/T5)
17
Low Flow Showerhead
50
Motors (Evaporator Fan)
37-38
Motors (Premium Efficiency)
47-48
Network Power Management Software
50
Night Covers for Display Cases
33
Occupancy Sensors (Lighting)
21
Occupancy Sensors (Plug Load)
49
Ovens (Combination)
28
Ovens (Convection)
28-29
Ovens (Conveyor)
32
Ovens (Rack)
31
Ozone Laundry System
44
Photocells
22
Pipe Insulation
41-42
Pool Heaters (Commercial)
41
Pulse Start/Ceramic Metal Halide Fixtures
12-13
34
Refrigeration Display Case with Doors
Refrigerator (Commercial)
29-30
Refrigerators (Early Retirement)
50-51
Signage
23-24
Spa Heater (Commercial)
41
Sprinkler Nozzles
45
Sprinkler to Drip Irrigation
45
Steam Cookers
25
Steam Traps
43
Strip Curtains Product closed effective March 31, 2011
33-34
Tank Insulation
42
Time Clocks
22-23
Variable Frequency Drives (VFDs)
51
Vending Machine Controllers
51
39-41
Water Heaters and Boilers
Window Film
49
Wine Tank insulation — Product closed December 31, 2011
46
53
© 2012 San Diego Gas & Electric Company. All copyright and trademark rights reserved. Trademarks are property of their respective owners.
S1280211 0912