Breadboard Voltage
Regulator Version 2.0
Convenient 5V Supply for Breadboard
Turn your 6~18VDC “Wall Wart” adapter into a regulated 5VDC
@ 0.5 Ampere supply for your breadboard experiments!
Build Time: 20mins
Skill Level: Beginner (2/5)
! Power Switch
! LED Power Indicator
! Polarity Configurable
! Handy like you won’t believe!
www.solarbotics.com
SKU: 34020
http://www.solarbotics.com/products/34020/
1-866-276-2687
Document Revision: March 8th, 2010
You’ll find the BVRv2 to be a pretty handy addition to your
workstation. It’s an easy kit to build, but it is still a good
idea to quick read through the instructions just to make
sure you’re building it right.
Don’t know how to solder? No problem!
Download our free soldering tutorial online at:
http://www.hvwtech.com/resources.asp
We strongly suggest you inventory the parts in your kit to make sure you have all
the parts listed. If anything is missing, contact Solarbotics Ltd. / HVW Technologies
for replacement parts information.
Disclaimer of Liability - a.k.a. Legalese to make the lawyers happy
Solarbotics Ltd. is not responsible for any special, incidental, or consequential
damages resulting from any breach of warranty, or under any legal theory,
including lost profits, downtime, good-will, damage to or replacement of
equipment or property, and any costs or recovering of any material or goods
associated with the assembly or use of this product. Solarbotics Ltd. reserves the
right to make substitutions and changes to this product without prior notice. And to
leave chocolate chip cookie crumbs on your couch.
www.solarbotics.com
2
BVR Manual v3.2
Parts List
Printed Circuit
Board (PCB)
R1 - 1k
Resistor
Barrel Jack
10µF
Capacitor
Power
Switch
Power
LED
Pin
Headers 5V
(x 4)
Regulator
C2 - 0.1µF
Capacitor
1
1
1
1
1
1
1
1
4
x
x
x
x
x
x
x
x
x
Printed Circuit Board
Power Switch
2.1mm DC Power Connector Barrel Jack
C1 - 10µF Electrolytic Capacitor
C2 - 0.1µF Monolithic Capacitor
5V Voltage Regulator
1k Resistor (Brown/Black/Red)
Red Power Indicator LED
Pin Headers
www.solarbotics.com
3
BVR Manual v3.2
Construction
1.0k Resistor
0.1µF
Capacitor
1. Resistor & 0.1µF Capacitor:
Remove the tape, and bend the
leads of the resistor over, and
insert it into the position labeled
‘R1’. Solder it in from the other
side, and snip the excess leads.
Do the same for the 0.1µF
capacitor into position ‘C2’. It
doesn't matter which way these
parts are installed - they are
polarity insensitive.
2. Voltage Regulator & Barrel
Jack:
Solder the Voltage Regulator to
the ‘V-REG’ position. Make sure
the tab-side aligns with the fat
line on the symbol. Backwards
won’t work! Then trim off the
excess leads.
Snap the Barrel Jack into position
‘B1’ and solder it into place.
Voltage
Regulator
Barrel
Jack
Tab
Tab Line
Finished Install
www.solarbotics.com
4
BVR Manual v3.2
3. 10µF Capacitor & Power
LED:
Install the 10µF
electrolytic capacitor into
position ‘C1’. Position is
c r i t i c a l
(otherwise,*poof*). Make
LED - Note Longer
10µF Cap Lead goes to round
Note Longer Lead
sure the longer lead goes
pad
goes to ‘+’
into the pad marked (+).
Confirm by checking that
the stripe on the side of the capacitor is nearest to the “PWR”
label.
Similar plan with the LED - longer lead goes into the round pad. You
can confirm by noting the little notch on the LED is on the side of
the LED symbol with the line (near the square pad).
Pins on
UNDERSIDE
4. Power Switch &
Breadboard Pins:
T h e Po w e r S w i t c h
simply mounts into the
position ‘PWR’. Nothing
difficult.
The breadboard pins are
a bit more difficult, as
they go on the
underside, and are
harder to hold while
soldering. If you are confident, push the long side of the pins into
your breadboard so they match the holes in the PCB, and solder
them in while the breadboard holds everything in alignment.
Otherwise, carefully solder them in as straight as you can by hand.
www.solarbotics.com
5
BVR Manual v3.2
5. Configuring Power Rails:
THIS IS IMPORTANT - Forget
to do this, and your BVRv2
won’t work!
Choose which side of the
breadboard you want your
BVRv2 to mount (here we use
the left side). Note the polarity
of the breadboard rails (+ on
bottom, ‘-’ on top.
2. Solder blobs on
set of pads matching
rail polarity
Find which set of pads on the
BV R v 2 m a t c h t h i s
arrangement, and put a blob of
solder across the little ½
moons.
If you plan to switch the
polarity of the power on the
rails (kinda dangerous), you
can mount part number SWT7
on the pads between the blob
pads. Do not put any blobs on
the pads if you do this. This is
generally not a recommended
modification!
1. Note
Breadboard
Rail Polarity
Using a SWT7 instead
of solder blobs - not
generally recommended!
Power your BVRv2 with any DC power source rated 6~18 volts
(35VDC max!). The power regulator will warm when powered
with over 12V (that’s ok).
If you don’t want to use it on a breadboard, use the solder pads
labeled “+ -” points on the end nearest the barrel jack for 5V
regulated power output. Enjoy your BVR!
www.solarbotics.com
6
BVR Manual v3.2
Technical Support
Technical support is available if you are having problems - please
contact us and provide as much detailed information as possible.
E-mail: support@hvwtech.com
Phone: (403) 730-8603
(Monday - Friday 9am – 5pm Mountain time)
Get prototyping!
with other great products from HVW Technologies:
Stamp Stack II: A complete BASIC
Stamp II on a board that mounts onto a
solderless breadboard. Includes a serial
connector, reset switch and a “bulletproof” power supply.
'AXE Stack-18: This mounts on any
breadboard for total prototyping
flexibility of the PICAXE series of
microcontrollers.
Plus...
Ÿ
FPGA Development Kits
Ÿ
Robotics Kits/Part
Ÿ
Instructional Books
Ÿ
Gifts & Toys
Ÿ
Tools and test equipment
Microcontrollers
Ÿ
Ÿ
IR Sensors
Ÿ
Compilers
Ÿ
PIC Programmers
Ÿ
Proto Boards
www.solarbotics.com
7
BVR Manual v3.2
Fast and practical breadboard power
The BVR has been
specially designed to
mount onto the power rails
of a standard breadboard
and accepts any standard
2.1 mm barrel plug found
on most AC adapters. This
makes it ideal for many
prototyping projects!
Visit us online for more info and cool stuff:
www.solarbotics.com
Solarbotics Ltd.
201 35th Ave NE
Calgary, Alberta T2E 2K5
Canada
Toll Free: 1-866-276-2687
International: +1 (403) 232-6268
Fax: +1 (403) 226-3741
Email: sales@solarbotics.com
Made in Canada