TCBE/TCBL/TCBC
Technical Workstation Assembly
TCBE
Hardware List
2 – Universal End Frame
1 – Upper Front Rail
1 – Lower Rear Rail
1 – Rear Support Frame
10 – 5/16-18 x 3” Stainless Steel Button Head Machine Screw
10 – 8mm Stainless Steel Flat Washer
8 – 1/4-20 x 3/4” Phillips Pan Head Thread-Cutting Machine Screws
X - #12 x 3/4” Phillips Pan Head Sheet Metal Screws
(Quantity varies with size of table)
60” wide Technical Workstation
with double bay uprights require
special outer brackets. (See
DBUP53-TC)
*If no uprights discard this note.
Rear Support Frame
Upper Front Rail
Lower Rear Rail
TCBE version of table,
(shown) with adjustable
legs. Yours may have
casters or leveler glides.
Universal End Frame
fig – 1
Assembly can be done in an upright position, but is easier to assemble lying on its back.
First, locate all of the parts that are shown in (fig-1) plus the fasteners. Attach all of the
rails (finger tight) as shown in (fig-3). Then, starting with the Rear Support Frame tighten
them securely, this will hold the complete frame square while finishing tightening all of
the other rails.
BOSTONtec  2700 James Savage Road  Midland, MI 48642
 Tel (989) 496-9510  Fax (989) 496-9927  www.bostontec.com
1
TCBE/TCBL/TCBC
Technical Workstation Assembly
If your table has adjustable leg extensions as shown in (fig-2), they will come
installed at the lowest position. To set at the height desired, remove the 1/4-20 x
3/4” Phillips Pan Head Thread-Cutting Machine Screws, and position the
extension leg where the height is needed. Then, re-attach extensions to legs
using existing screws.
1/4-20 x 3/4” Phillips Pan
Head Thread-Cutting
Machine Screws
Square tube leg
extensions with leveler
Glides installed
Fig-2
BOSTONtec  2700 James Savage Road  Midland, MI 48642
 Tel (989) 496-9510  Fax (989) 496-9927  www.bostontec.com
2
TCBE/TCBL/TCBC
Technical Workstation Assembly
Rear support frame must be flush with
top and rear face of End Frame
8mm Stainless Steel
Flat Washer
5/16-18 x 3” Stainless Steel
Button Head Machine Screws
Fig-3
Lower rear rail end view ½” longer than upper front rail
Upper front rail end view
Attach the Rear Support Frame to the Universal End Frames with (4) 5/16-18 x 3”
Stainless Steel Button Head Machine Screws and (4) Stainless Steel Flat
Washers. Next, attach the Upper Front Rail to the End Frames using same bolt
and washer at each end. Then, attach the Lower Rear Rail using two bolts and
washers at each end. See (fig-3).
*Make sure all rails are square with the end frame while
tightening bolts.
BOSTONtec  2700 James Savage Road  Midland, MI 48642
 Tel (989) 496-9510  Fax (989) 496-9927  www.bostontec.com
3
TCBE/TCBL/TCBC
Technical Workstation Assembly
For all countertops, excluding epoxy tops, attach the countertop with #12 x 3/4”
Phillips Pan Head Sheet Metal Screws, as shown in (fig-4). Quantity of screws
varies by the size of table. Position the top so it is flush with the back of the table
and centered left to right on the sides. For epoxy tops, attach by using silicone
adhesive on top four rails of the table frame.
Countertop
#12 x 3/4” Phillips Pan Head
Sheet Metal Screws
Fig-4
BOSTONtec  2700 James Savage Road  Midland, MI 48642
 Tel (989) 496-9510  Fax (989) 496-9927  www.bostontec.com
4
TCBE/TCBL/TCBC
Technical Workstation Assembly
Attach the half depth and full depth shelves using silicone adhesive. For half
depth shelf see (fig-5) and for full depth shelf see (fig-6). For half depth shelf,
install rail in the middle of the end frame and for the full depth shelf, install rail at
the front hole location, using (4) 5/16-18 x 3” Stainless Steel Button Head
Machine Screws and (4) Stainless Steel Flat Washers.
8mm Stainless Steel
Flat Washer
Fig-5
5/16-18 x 3” Stainless Steel
Button Head Machine Screws
8mm Stainless Steel
Flat Washer
Fig-6
5/16-18 x 3” Stainless Steel
Button Head Machine Screws
BOSTONtec  2700 James Savage Road  Midland, MI 48642
 Tel (989) 496-9510  Fax (989) 496-9927  www.bostontec.com
5