R Mobile CB frequency antenna with magnetic base Technical data for the Zephir series Spring Stainless Steel antenna whip EPDM Gasket Stainless Steel pressure screw O-ring sealing Polycarbonate coil cover Type: Car antenna for the magnetic assembly. The magnetic base is supplied as an imported accessorie and have 2 year warranty Maximum bent angle: 90° Material: metal mouldings: aluminium alloy plastic mouldings: polycarbonate Gaskets: EPDM O-ring sealing: NBR antenna whip: sspring stainless steel Wing screw: Zinc coated steel with Polyester Powder Coating Whip pressure screw: stainless steel Assembly screw: Zinc coated steel grade 5.8 Various of the magntic bases may be equipped with the fixing scerw which requires smaller antenna foot. O-ring sealing One hand operated joint 1.Magnetic base with DZ connection, 4m RG58 cable and UC01 connector (PL259) Rubber Pad Rubber magnetic pad is the element which weares down during usage. Rubber magnetic pad is the item which prevents car coating from sratches during installing and atkeing of atenna. It is made from ferromagnetic material inside the flexible plastic. It is obligatory to take it off every few days as when it is left on the car body during the heat and sunshing may ocure in loosing its flexibility and permament glueing. The Rubber magnetic pad is polish product and have 2 year warranty. Magnetic Rubber Pad 5903792741494 - Product code EAN of the magnetic base of the diameter 145mm including the magnetic pad of 160mm diameter .Magnetic base is supplied separately from the antennas. Antennas are supplied as per table below. product code EAN Type nett gross effitiency relative Max Overall whip lenght (only antenna) weight weight SWR sensivity power height** range* 5903792741005 305 g 335 g 1,05-1,15 1,8 dB 150 W 71 cm 50 - 59 cm Z 500 5903792741012 315 g 360 g 1,02-1,18 2,1 dB 250 W 112 cm 90 - 99 cm Z 900 5903792741029 320 g 365 g 2,3 dB 250 W Z 1200 1,11-1,20 130 cm 115 - 125 cm 5903792741036 325 g 370 g 2,5 dB Z 1350 250W 1,09-1,26 149 cm 130 - 135 cm 5903792741043 350 g 400 g 2,8 dB Z 1500 250 W 1,10-1,18 168 cm 148 - 155 cm */ Very long antenna whip is provided to prevent extreme tunning problems. Usually it must be shorten. Tunning with SWR meter is obligatory and sometimes it can be shorten even for 10cm. The antenna whip catching allows for the 3cm regulation without cutting. It is better to shorten the whip when it is pushed to catching as deep as it is possible since the whip is shorten too much it can be stell taken out. **/ Height form the mounting surface for the antenna before tunning. During tunning it's beeing shorten R Mobile CB frequency antenna for the direct assembly Technical data of the Typhoon series: Spring Stainless Steel antenna whip EPDM Gasket Type: For direct assembly Diameter of the assembly hole: 9mm Cable lenght: 4 m Cable type: RG58 Cu/Cu, flexible cover for the wide range of temperatures Maximum bent angle: 90° stainless steel pressure screw Material: metal mouldings: aluminium alloy plastic mouldings: polycarbonate Gaskets: EPDM O-ring sealing: NBR antenna whip: sspring stainless steel Wing screw: Zinc coated steel with Polyester Powder Coating Whip pressure screw: stainless steel Assembly screw: Zinc coated steel grade 5.8 O-ring sealing Polycarbonate coil cover The antenna is supplied with the Zinc coated 5.8 grade fixing screw of size M6 x 45, which is dedicated to assembly with 0,6 - 3mm thick steel plate. For the assembly with plates thicker than 3mm please follow the instructions shown in the table below. O-ring sealing One hand operated joint assembly range of the screw steel plate thickness M6 x 45 M6 x 50 M6 x 55 M6 x 60 M6 x 65 M6 x 70 M6 x 75 M6 x 80 M6 x 85 M6 x 90 M6 x 95 additional coil EPDM Gasket Type EN ring connector for the RG58 Cu/Cu 4m cable wtih M6x45 fixing screw and rubber cover. Supplied without plug product code EAN Type 5903792741111 5903792741135 5903792741159 T 1100 T 1550 T 1750 nett weight 465 g 480 g 487 g gross weight 510 g 525 g 532 g effitiency SWR 1,01-1,21 1,08-1,26 1,04-1,22 relative sensivity 2,8 dB 3,5 dB 4,2 dB max power 500 W 500 W 500 W For the assembly with very thin 0,6 - 3 mm plates please use big diameter 2,0 - 8 mm steel washer 7,0 - 13 mm 12 - 18 mm 17 - 23 mm 22 - 28 mm 27 - 33 mm 32 - 38 mm 37 - 43 mm 42 - 48 mm 47 - 53 mm overall height** 134 cm 170 cm 190 cm Requires use of the additional insulating tube for the fixing screw range of the whip lenght* 108 - 118 cm 145 - 155 cm 165 - 175 cm */ Very long antenna whip is provided to prevent extreme tunning problems. Usually it must be shorten. Tunning with SWR meter is obligatory and sometimes it can be shorten even for 10cm. The antenna whip catching allows for the 5cm regulation without cutting. It is better to shorten the whip when it is pushed to catching as deep as it is possible since the whip is shorten too much it can be stell taken out. **/ Height form the mounting surface for the antenna before tunning. During tunning it's beeing shorten. R Mobile CB frequency antenna for the direct assembly Technical data of the Typhoon series: Spring Stainless Steel antenna whip Type: For direct assembly Diameter of the assembly hole: 9mm Cable lenght: 4 m Cable type: RG58 Cu/Cu, flexible cover for the wide range of temperatures Maximum bent angle: 90° EPDM Gasket stainless steel pressure screw O-ring sealing Material: metal mouldings: aluminium alloy plastic mouldings: polycarbonate Gaskets: EPDM O-ring sealing: NBR antenna whip: sspring stainless steel Wing screw: Zinc coated steel with Polyester Powder Coating Whip pressure screw: stainless steel Assembly screw: Zinc coated steel grade 5.8 Polycarbonate coil cover O-ring sealing One hand operated joint The antenna is supplied with the Zinc coated 5.8 grade fixing screw of size M6 x 25, which is dedicated to assembly with 0,6 - 3mm thick steel plate. For the assembly with plates thicker than 3mm please follow the instructions shown in the table below. assembly range of the screw steel plate thickness EPDM Gasket Product code EAN Type EN ring connector for the RG58 Cu/Cu 4m cable wtih M6x25 fixing screw and rubber cover. Supplied without plug Type M6 x 25 M6 x 30 M6 x 35 M6 x 40 M6 x 45 M6 x 50 M6 x 55 M6 x 60 M6 x 65 M6 x 70 M6 x 75 0,6 - 3 mm 2,0 - 8 mm 7,0 - 13 mm 12 - 18 mm 17 - 23 mm 22 - 28 mm 27 - 33 mm 32 - 38 mm 37 - 43 mm 42 - 48 mm 47 - 53 mm For the assembly with very thin plates please use big diameter steel washer nett gross effitiency relative max overall whip lenght weight weight SWR sensivity power height** range* 305 g 335 g 1,05-1,14 2,0 dB 150 W 71 cm 50 - 59 cm 5903792741005 Z 500 315 g 360 g 1,00-1,17 2,2 dB 250 W 112 cm 90 - 99 cm 5903792741012 Z 900 320 g 365 g 1,10-1,22 2,5 dB 250 W 5903792741029 Z 1200 130 cm 115 - 125 cm 325 g 370 g 1,08-1,26 2,8 dB 5903792741036 Z 1350 250W 149 cm 130 - 135 cm 350 g 400 g 1,09-1,18 3,0 dB 5903792741043 Z 1500 250 W 168 cm 148 - 155 cm */ Very long antenna whip is provided to prevent extreme tunning problems. Usually it must be shorten. Tunning with SWR meter is obligatory and sometimes it can be shorten even for 10cm. The antenna whip catching allows for the 5cm regulation without cutting. It is better to shorten the whip when it is pushed to catching as deep as it is possible since the whip is shorten too much it can be stell taken out. **/ Height form the mounting surface for the antenna before tunning. During tunning it's beeing shorten.