Baying systems TS 8
Height: 1200, depth: 500/height: 1400, depth: 500
F1
T
F1
T
B
G1
H
G1
B
H
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Width (B) mm
Packs of
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Approvals,
see page 30.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
600
800
1200
600
800
1200
Height (H) mm
1200
1200
1200
1400
1400
1400
Depth (T) mm
500
500
500
500
500
500
Mounting plate width (F1) mm
499
699
1099
499
699
1099
Mounting plate height (G1) mm
Model No. TS
1
1096
1096
1096
1296
1296
1296
8615.500
8815.500
8215.500
8645.500
8845.500
8245.500
Door(s)
Weight (kg)
1
1
2
1
1
2
74.5
92.1
140.0
86.0
107.5
163.5
Page
Walls
Side panels
2
8115.235
8115.235
8115.235
8145.235
8145.235
8145.235
917
Divider panel
1
–
–
–
8609.450
8609.450
8609.450
921
Height 100 mm
1 set
8601.600
8601.800
8601.200
8601.600
8601.800
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.200
8602.600
8602.800
8602.200
893
Height 100 mm
1 set
8601.050
8601.050
8601.050
8601.050
8601.050
8601.050
893
Height 200 mm
1 set
8602.050
8602.050
8602.050
8602.050
8602.050
8602.050
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4196.000
4191.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4947.000
4944.000
4945.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4596.000
4596.000
4598.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4116.000
4116.000
4118.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Signal pillar LED compact,
Model No. see page 1125.
Baying cover, top,
Model No. see page 932.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329
138
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 1600, depth: 500
F1
F1
T
B
B
G1
H
G1
T
H
B
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Width (B) mm
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Approvals,
see page 30.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Packs of
600
800
1200
Height (H) mm
1600
1600
1600
Depth (T) mm
500
500
500
Mounting plate width (F1) mm
499
699
1099
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
Baying systems TS 8
1.3
1496
1496
1496
8665.500
8865.500
8265.500
1
1
2
100.0
103.0
159.3
Page
Walls
Side panels
2
8165.235
8165.235
8165.235
917
Divider panel
1
8609.650
8609.650
8609.650
921
Height 100 mm
1 set
8601.600
8601.800
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.200
893
Height 100 mm
1 set
8601.050
8601.050
8601.050
893
Height 200 mm
1 set
8602.050
8602.050
8602.050
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Connector gland
for connecting a keyboard,
mouse or scanner,
Model No. see page 1057.
Hinge attachment
for partial mounting plates,
Model No. see page 985.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329
Rittal Catalogue 32/Industrial Enclosures
139
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 1800, depth: 400
F1
T
F1
T
B
G1
H
G1
B
H
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Width (B) mm
Packs of
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Accessories:
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
600
800
1000
1000
1200
Height (H) mm
1800
1800
1800
1800
1800
Depth (T) mm
400
400
400
400
400
Mounting plate width (F1) mm
499
699
899
899
1099
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
1696
1696
1696
1696
1696
8684.500
8884.500
8084.500
8080.500
8284.500
1
1
1
2
2
91.3
113.5
136.4
140.0
170.6
Page
Walls
Side panels
2
8184.235
8184.235
8184.235
8184.235
8184.235
917
Divider panel
1
8609.840
8609.840
8609.840
8609.840
8609.840
921
Height 100 mm
1 set
8601.600
8601.800
8601.000
8601.000
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.000
8602.000
8602.200
893
Height 100 mm
1 set
8601.040
8601.040
8601.040
8601.040
8601.040
893
Height 200 mm
1 set
8602.040
8602.040
8602.040
8602.040
8602.040
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4336.000
4336.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4946.000
4946.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4599.000
4309.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4124.000
4115.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Snap-on nut
for screw-fastening to the
vertical section,
Model No. see page 1005.
System window
to protect against unauthorised
access and preserve the protection category,
Model No. see page 943.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Ppage 632
140
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 1800, depth: 500
F1
T
F1
T
B
G1
H
G1
B
H
B
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12
(except TS 8485.510).
Width (B) mm
Packs of
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Accessories:
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
400
600
800
800
1200
Height (H) mm
1800
1800
1800
1800
1800
Depth (T) mm
500
500
500
500
500
–
499
699
699
1099
Mounting plate width (F1) mm
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
Baying systems TS 8
1.3
–
1696
1696
1696
1696
8485.5101)
8685.500
8885.500
8880.500
8285.500
1
1
1
2
2
49.2
93.8
115.8
122.5
173.3
Page
Walls
Side panels
2
8185.235
8185.235
8185.235
8185.235
8185.235
Divider panel
1
8609.850
8609.850
8609.850
8609.850
8609.850
917
921
Divider panel for module plates
1
8609.100
8609.100
8609.100
8609.100
8609.100
922
Height 100 mm
1 set
8601.400
8601.600
8601.800
8601.800
8601.200
893
Height 200 mm
1 set
8602.400
8602.600
8602.800
8602.800
8602.200
893
Height 100 mm
1 set
8601.050
8601.050
8601.050
8601.050
8601.050
893
Height 200 mm
1 set
8602.050
8602.050
8602.050
8602.050
8602.050
893
Cable clamp rails for cable clamps
2
4193.000
4191.000
4192.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
–
4944.000
4945.000
4945.000
4947.000
999
Support strips for door
20
–
4596.000
4598.000
4594.000
4596.000
964
Wiring plan pocket, sheet steel
1
–
4116.000
4118.000
4114.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
1) Without
tubular door frame, mounting plate and gland plates. Available to order as accessories: Mounting plate, see page 987, gland plates, see from page 911.
To order enclosures in textured RAL 7032 please add extension .600 or .610 to the Model No., and for primed enclosures use extension .800 or .810.
Delivery times available on request.
Interface flap
for safe, modular accommodation of sockets and interfaces,
Model No. see page 1151.
Compact light
for space-saving installation on
a vertical or horizontal section,
Model No. see page 1027.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
Rittal Catalogue 32/Industrial Enclosures
141
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 1800, depth: 600
F1
T
F1
T
B
G1
H
G1
B
H
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12
(except TS 8486.510).
Mounting plates and gland
plates: Zinc-plated
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel, roof plate and
2 support strips
(TS 4696.000, see page 997),
fitted in the enclosure depth.
Width (B) mm
Packs of
Accessories:
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
400
600
800
800
1200
Height (H) mm
1800
1800
1800
1800
1800
Depth (T) mm
600
600
600
600
600
–
499
699
699
1099
Mounting plate width (F1) mm
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
–
1696
1696
1696
1696
8486.5101)
8686.500
8886.500
8881.500
8286.500
1
1
1
2
2
51.7
96.8
120.3
125.8
179.9
Page
Walls
Side panels
2
8186.235
8186.235
8186.235
8186.235
8186.235
Divider panel
1
8609.860
8609.860
8609.860
8609.860
8609.860
917
921
Divider panel for module plates
1
8609.110
8609.110
8609.110
8609.110
8609.110
922
Climate control side panel
1
3331.XXX
3331.XXX
3331.XXX
3331.XXX
3331.XXX
635
Height 100 mm
1 set
8601.400
8601.600
8601.800
8601.800
8601.200
893
Height 200 mm
1 set
8602.400
8602.600
8602.800
8602.800
8602.200
893
Height 100 mm
1 set
8601.060
8601.060
8601.060
8601.060
8601.060
893
Height 200 mm
1 set
8602.060
8602.060
8602.060
8602.060
8602.060
893
Cable clamp rails for cable clamps
2
4193.000
4191.000
4192.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
–
4944.000
4945.000
4945.000
4947.000
999
Support strips for door
20
–
4596.000
4598.000
4594.000
4596.000
964
Wiring plan pocket, sheet steel
1
–
4116.000
4118.000
4114.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
1) Without
tubular door frame, mounting plate and gland plates. Available to order as accessories: Mounting plate, see page 987, gland plates, see from page 913.
To order enclosures in textured RAL 7032 please add extension .600 or .610 to the Model No., and for primed enclosures use extension .800 or .810.
Delivery times available on request.
TFT monitor
for installation in doors and side
panels,
Model No. see page 1133.
Gland plates,
Model No. see from page 911.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
142
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 2000, depth: 400
F1
T
F1
T
B
G1
H
G1
B
H
B
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame:
Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Accessories:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Width (B) mm
Possible
alternative:
600
800
1000
1200
Height (H) mm
Packs of
2000
2000
2000
2000
Depth (T) mm
400
400
400
400
Mounting plate width (F1) mm
499
699
899
1099
Mounting plate height (G1) mm
Model No. TS
Baying systems TS 8
1.3
1
Door(s)
Weight (kg)
1896
1896
1896
1896
8604.500
8804.500
8004.500
8204.500
1
1
2
2
99.0
124.0
152.8
184.5
Page
Walls
Side panels
2
8104.235
8104.235
8104.235
8104.235
917
Divider panel
1
8609.040
8609.040
8609.040
8609.040
921
Height 100 mm
1 set
8601.600
8601.800
8601.000
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.000
8602.200
893
Height 100 mm
1 set
8601.040
8601.040
8601.040
8601.040
893
Height 200 mm
1 set
8602.040
8602.040
8602.040
8602.040
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4336.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4946.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4309.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4115.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Cable trunking, vertical,
to match the section and horizontally to match the mounting plate,
Model No. see page 1059 – 1060.
Rail
for EMC shielding brackets and
cable clamps,
Model No. see page 1031.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
Rittal Catalogue 32/Industrial Enclosures
143
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 2000, depth: 500
F1
T
F1
T
B
G1
H
G1
B
H
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plate and gland
plates: Zinc-plated
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12
(except TS 8405.510).
Width (B) mm
Packs of
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Accessories:
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
400
600
800
1000
1200
Height (H) mm
2000
2000
2000
2000
2000
Depth (T) mm
500
500
500
500
500
–
499
699
899
1099
Mounting plate width (F1) mm
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
–
1896
1896
1896
1896
8405.5101)
8605.500
8805.500
8005.500
8205.500
1
1
1
2
2
60.7
101.3
126.3
157.1
190.6
Page
Walls
Side panels
2
8105.235
8105.235
8105.235
8105.235
8105.235
Divider panel
1
8609.050
8609.050
8609.050
8609.050
8609.050
917
921
Divider panel for module plates
1
8609.120
8609.120
8609.120
8609.120
8609.120
922
Height 100 mm
1 set
8601.400
8601.600
8601.800
8601.000
8601.200
893
Height 200 mm
1 set
8602.400
8602.600
8602.800
8602.000
8602.200
893
Height 100 mm
1 set
8601.050
8601.050
8601.050
8601.050
8601.050
893
Height 200 mm
1 set
8602.050
8602.050
8602.050
8602.050
8602.050
893
Cable clamp rails for cable clamps
2
4193.000
4191.000
4192.000
4336.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
–
4944.000
4945.000
4946.000
4947.000
999
Support strips for door
20
–
4596.000
4598.000
4309.000
4596.000
964
Wiring plan pocket, sheet steel
1
–
4116.000
4118.000
4115.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956 and comfort handle, see page 947 – 948.
1) Without
tubular door frame, mounting plate and gland plates. Available to order as accessories: Mounting plate, see page 987, gland plates, see from page 911.
To order enclosures in textured RAL 7032 please add extension .600 or .610 to the Model No., and for primed enclosures use extension .800 or .810.
Delivery times available on request.
Cable glands
of polyamide or brass,
Model No. see page 1054.
Keyboard,
pull-out with integral trackball,
Model No. see page 1137.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
144
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 2000, depth: 600
F1
T
F1
T
B
G1
H
G1
B
H
B
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12
(except TS 8406.510).
Mounting plates and gland
plates: Zinc-plated
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel, roof plate and
2 support strips
(TS 4696.000, see page 997),
fitted in the enclosure depth.
Width (B) mm
Packs of
Accessories:
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
400
600
800
1000
1200
Height (H) mm
2000
2000
2000
2000
2000
Depth (T) mm
600
600
600
600
600
–
499
699
899
1099
Mounting plate width (F1) mm
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
Baying systems TS 8
1.3
–
1896
1896
1896
1896
8406.5101)
8606.500
8806.500
8006.500
8206.500
1
1
1
2
2
55.7
104.0
130.5
161.2
194.6
Page
Walls
Side panels
2
8106.235
8106.235
8106.235
8106.235
8106.235
Divider panel
1
8609.060
8609.060
8609.060
8609.060
8609.060
917
921
Divider panel for module plates
1
8609.130
8609.130
8609.130
8609.130
8609.130
922
Climate control side panel
1
3331.XXX
3331.XXX
3331.XXX
3331.XXX
3331.XXX
635
Height 100 mm
1 set
8601.400
8601.600
8601.800
8601.000
8601.200
893
Height 200 mm
1 set
8602.400
8602.600
8602.800
8602.000
8602.200
893
Height 100 mm
1 set
8601.060
8601.060
8601.060
8601.060
8601.060
893
Height 200 mm
1 set
8602.060
8602.060
8602.060
8602.060
8602.060
893
Cable clamp rails for cable clamps
2
4193.000
4191.000
4192.000
4336.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
–
4944.000
4945.000
4946.000
4947.000
999
Support strips for door
20
–
4596.000
4598.000
4309.000
4596.000
964
Wiring plan pocket, sheet steel
1
–
4116.000
4118.000
4115.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
1) Without
tubular door frame, mounting plate and gland plates. Available to order as accessories: Mounting plate, see page 987, gland plates, see from page 911.
To order enclosures in textured RAL 7032 please add extension .600 or .610 to the Model No., and for primed enclosures use extension .800 or .810.
Delivery times available on request.
Section for cable entry
for top mounting on gland plates
with routing of the cable clamp
strip,
Model No. see page 1046.
Module plate
for cable entry in the divider
panel,
Model No. see page 923 – 924.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
Rittal Catalogue 32/Industrial Enclosures
145
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 2000, depth: 800
F1
T
F1
T
B
G1
H
G1
B
H
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Width (B) mm
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Possible
alternative:
Instead of a door or rear panel,
matching section doors with
integral cooling module,
see page 633 – 634.
Accessories:
Approvals,
see page 30.
Corner enclosures,
see page 933.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
600
800
1200
Height (H) mm
Packs of
2000
2000
2000
Depth (T) mm
800
800
800
Mounting plate width (F1) mm
499
699
1099
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
Page
1896
1896
1896
8608.500
8808.500
8208.500
1
1
2
111.3
137.0
203.0
Walls
Side panels
2
8108.235
8108.235
8108.235
Divider panel
1
8609.080
8609.080
8609.080
917
921
TS 8 internal fan mounting panel
1
3348.200
3348.200
3348.200
707
Height 100 mm
1 set
8601.600
8601.800
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.200
893
Height 100 mm
1 set
8601.080
8601.080
8601.080
893
Height 200 mm
1 set
8602.080
8602.080
8602.080
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Punched section without
mounting flange 45 x 88 mm
The universal configuration
solution with 11 rows of holes for
heavy equipment and screwfastening to the frame,
Model No. see page 995.
Mounting
plate attachment
in conjunction
with mounting
plate infill,
Model No.
see page 979.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
146
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Height: 2200, depth: 600
F1
F1
T
B
B
G1
H
G1
T
H
B
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Door: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame: Dipcoat-primed
Door, roof and rear panel:
Dipcoat-primed, powder-coated
in textured RAL 7035 on the
outside
Mounting plates and gland
plates: Zinc-plated
Width (B) mm
Protection category:
IP 55 to EN 60 529/09.2000,
complies with NEMA 12.
Accessories:
Corner enclosures,
see page 933.
Supply includes:
Enclosure frame with doors,
mounting plate, gland plates,
rear panel and roof plate.
Packs of
Approvals,
see page 30.
Detailed drawing/nominal
dimensions,
see page 1184 – 1185.
600
800
1200
Height (H) mm
2200
2200
2200
Depth (T) mm
600
600
600
Mounting plate width (F1) mm
499
699
1099
Mounting plate height (G1) mm
Model No. TS
1
Door(s)
Weight (kg)
Baying systems TS 8
1.3
2096
2096
2096
8626.500
8826.500
8226.500
1
1
2
113.1
139.3
208.0
Page
Walls
Side panels
2
8126.235
8126.235
8126.235
917
Divider panel
1
8609.260
8609.260
8609.260
921
Height 100 mm
1 set
8601.600
8601.800
8601.200
893
Height 200 mm
1 set
8602.600
8602.800
8602.200
893
Height 100 mm
1 set
8601.060
8601.060
8601.060
893
Height 200 mm
1 set
8602.060
8602.060
8602.060
893
Cable clamp rails for cable clamps
2
4191.000
4192.000
4196.000
1061
Cable clamp rails (C section) for cable clamps
6
4944.000
4945.000
4947.000
999
Support strips for door
20
4596.000
4598.000
4596.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4116.000
967
Base/plinth
Components front and rear
Trim panels (sides)
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in textured RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Gland plate with sealing bar
for sub-dividing the base
assembly for varying cable
entry,
Model No. see page 912.
Module plate with cable
sleeves
for cable diameters 10 – 65 mm,
Model No. see page 924.
Accessories Page 890 TS 8 stainless steel Page 322 TS 8 EMC-shielded Page 329 Modular climate control concept Page 632
Rittal Catalogue 32/Industrial Enclosures
147
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Electronic enclosure
T
B
H
Z
48
4
4
46 50
5
Z
B
Baying systems TS 8
1.3
Material:
Enclosure frame:
Sheet steel, 1.5 mm
Front frame:
Extruded aluminium sections
with die-cast corner pieces
Rear door: 2 mm sheet steel
Roof and gland plates:
1.5 mm sheet steel
Adaptor sections: Aluminium
Surface finish:
Enclosure frame:
Dipcoat-primed
Front frame, rear door and roof:
Powder-coated in RAL 7035
Gland plates: Zinc-plated
U
Packs of
Supply includes:
Enclosure frame, front frame
(r/h hinge, opening angle 130°,
held via mechanical snap fasteners on left),
rear door (r/h hinge, may be
swapped to opposite side), roof,
adaptor sections and gland
plates.
Approvals,
see page 31.
Detailed drawing/nominal
dimensions,
see page 1186.
33
33
42
42
Width (B) mm
600
600
600
600
Height (H) mm
1600
1600
2000
2000
Depth (T) mm
600
800
600
800
8410.510
8418.510
8430.510
8438.510
1
1
1
1
Model No. TS
1
Door(s)
Page
Base/plinth
Height 100 mm
1 set
8601.600
8601.600
8601.600
8601.600
893
Height 200 mm
1 set
8602.600
8602.600
8602.600
8602.600
893
Height 100 mm
1 set
8601.060
8601.080
8601.060
8601.080
893
Height 200 mm
1 set
8602.060
8602.080
8602.060
8602.080
893
Side panels
2
8166.235
8168.235
8106.235
8108.235
917
Cable clamp rails for cable clamps
2
4191.000
4191.000
4191.000
4191.000
1061
Components front and rear
Trim panels (sides)
Accessories
Cable clamp rails (C section) for cable clamps
6
4944.000
4944.000
4944.000
4944.000
999
Adaptor sections for rear
2
8613.360
8613.360
8613.300
8613.300
1090
Lock systems
Standard double-bit lock insert (in rear door) may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
For primed enclosures, please add extension .810 to the Model No. Delivery times available on request.
Slide rails,
Model No. see page 1097.
Aluminium cross rail,
for sub-division of the front,
Model No. see page 1090.
Accessories Page 890 482.6 mm (19″) mounting accessories From page 1079 Subrack systems Page 548
482.6 mm (19″) climate control Page 698 – 700
148
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
For modular front design
T
H
B
B
The basic enclosures without
● Mounting plate
for universal interior installation with
− Partial mounting plates
− Component shelves and
drawers
− Punched sections and rails
● Doors
Frame for the installation of
− Partial doors with and
without viewing panels
− Fully glazed doors
− Drawers and desk sections
− Profile blanking frame
− Vertically divided doors
− Trim panels hinged at the top
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates: 1.5 mm
Supply includes:
Enclosure frame, roof,
rear panel, gland plates,
three-piece.
Detailed drawing
(TS basic enclosures without
door),
see page 1186.
Baying systems TS 8
1.3
Surface finish:
Enclosure frame:
Dipcoat-primed
Door and rear panel:
Dipcoat-primed,
powder-coated in textured
RAL 7035 on the outside
Gland plates: Zinc-plated
Width (B) mm
Packs of
Height (H) mm
Depth (T) mm
Model No. TS
1
Weight (kg)
600
800
2000
2000
600
600
8606.512
8806.512
52.5
63.0
Page
Walls
Side panels
2
8106.512
8106.512
942
Divider panel
1
8609.060
8609.060
921
Divider panel for module plates
1
8609.130
8609.130
922
Height 100 mm
1 set
8601.600
8601.800
893
Height 200 mm
1 set
8602.600
8602.800
893
Height 100 mm
1 set
8601.060
8601.060
893
Height 200 mm
1 set
8602.060
8602.060
893
Base/plinth
Components front and rear
Trim panels (sides)
To order enclosures in textured RAL 7032 please add extension .612 to the Model No., and for primed enclosures use extension .812.
Delivery times available on request.
Trim panels TS
For height trim at the top and
bottom,
Model No. see page 941.
Protective bar and holder,
Model No. see page 938.
Accessories Page 890 Partial doors Page 941 Partial mounting plates Page 984
Rittal Catalogue 32/Industrial Enclosures
149
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
For isolator door locking
F
T
B
H
G
B2
B
Baying systems TS 8
1.3
Material:
Sheet steel
Enclosure frame, roof, rear panel
and gland plates:
1.5 mm
Door and trim panel: 2.0 mm
Mounting plate: 3.0 mm
Surface finish:
Enclosure frame:
Dipcoat-primed
Door, trim panel, roof and
rear panel:
Dipcoat-primed,
powder-coated in textured
RAL 7035 on the outside
Mounting plates and gland
plates: Zinc-plated
Width (B) mm
Packs of
Height (H) mm
Protection category:
IP 55 to EN 60 529/09.2000
Complies with NEMA 12
(with fitted/sealed isolator switch
actuation)
Rittal service:
Enclosures with 100 mm
(instead of 200 mm) wide trim
panel on request.
Supply includes:
Enclosure frame, door
(l/h hinge),
trim panel (r/h hinge, with a
swing lever at the top and
bottom, with cut-out for isolator
switch actuation), roof, rear
panel, mounting plate, threepiece gland plates.
Approvals,
see page 31.
Detailed drawing/nominal
dimensions,
see page 1187.
800
800
800
800
1800
1800
2000
2000
Depth (T) mm
400
500
500
600
Mounting plate width (F) mm
699
699
699
699
Mounting plate height (G) mm
Model No. TS
1
Door(s)
Weight (kg)
1696
1696
1896
1896
8984.500
8985.500
8905.500
8906.500
1
1
1
1
113.5
115.8
126.3
130.5
Page
Base/plinth
Components front and rear
Trim panels (sides)
Height 100 mm
1 set
8601.800
8601.800
8601.800
8601.800
893
Height 200 mm
1 set
8602.800
8602.800
8602.800
8602.800
893
Height 100 mm
1 set
8601.040
8601.050
8601.050
8601.060
893
Height 200 mm
1 set
8602.040
8602.050
8602.050
8602.060
893
Also required
Door latch for bayed suites
960
Accessories
Isolator door locking (USA version)
1
8611.310
8611.310
8611.310
8611.310
960
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
To order enclosures in RAL 7032 please add extension .600 to the Model No., and for primed enclosures use extension .800.
Delivery times available on request.
Cable gland
Cable glands made from
polyamide or brass,
Model No. see page 1054.
Snap-on nut
for screw-fastening to the
vertical section,
Model No. see page 1005.
Accessories Page 890 Adjacent door locking Page 951
150
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
IP 66/NEMA 4x, NEMA 4
F
T
H
G
B
B
Material:
NEMA 4x:
Stainless steel 1.4301 (AISI 304)
NEMA 4:
Sheet steel, spray-finished
Enclosure frame, roof, base/
plinth, rear panel, side panels:
1.5 mm
Door: 2.0 mm
Mounting plate:
3.0 mm (sheet steel)
Surface finish:
NEMA 4x:
Enclosure frame: Uncoated
Door, roof, base, rear panel,
side panels: Brushed on the
outside, grain size 400
Mounting plate: Zinc-plated
Protection category:
IP 66 to EN 60 529/09.2000
(complies with NEMA 4x/
NEMA 4)
NEMA 4:
Enclosure frame, door, roof,
base, rear panel, side panels:
Dipcoat-primed
and powder-coated in textured
RAL 7035 on the outside
Mounting plate: Zinc-plated
Supply includes:
NEMA 4x/NEMA 4:
Enclosure frame with door,
roof/base plate, rear panel,
side panels, mounting plate.
NEMA 4x, stainless steel
Packs of
Rittal service:
Enclosures with depth 800 mm
on request.
Approvals,
see page 31.
NEMA 4, sheet steel
Page
Width (B) mm
600
800
600
800
600
800
600
800
Height (H) mm
1800
1800
2000
2000
1800
1800
2000
2000
Depth (T) mm
600
600
600
600
600
600
600
600
Mounting plate width (F) mm
499
699
499
699
499
699
499
699
Mounting plate height (G) mm
1696
1696
1896
1896
1696
1696
1896
1896
8458.640
8459.640
8452.640
8450.640
8686.540
8886.540
8606.540
8806.540
1
1
1
1
1
1
1
1
Model No. TS
1
Door(s)
Baying systems TS 8
1.3
Base/plinth
Height 100 mm
1 set
8701.600
8701.800
8701.600
8701.800
8601.600
8601.800
8601.600
8601.800 893, 899
Height 200 mm
1 set
8702.600
8702.800
8702.600
8702.800
8602.600
8602.800
8602.600
8602.800 893, 899
Height 100 mm
1 set
8701.060
8701.060
8701.060
8701.060
8601.060
8601.060
8601.060
8601.060 893, 899
Height 200 mm
1 set
8702.060
8702.060
8702.060
8702.060
8602.060
8602.060
8602.060
8602.060 893, 899
4
2913.000
2913.000
2913.000
2913.000
–
–
–
–
899
Cable clamp rails
2
4191.000
4192.000
4191.000
4192.000
4191.000
4192.000
4191.000
4192.000
1061
System support rails
2
4361.000
4362.000
4361.000
4362.000
4361.000
4362.000
4361.000
4362.000
1000
Support strips for door
20
4596.000
4598.000
4596.000
4598.000
4596.000
4598.000
4596.000
4598.000
964
Wiring plan pocket, sheet steel
1
4116.000
4118.000
4116.000
4118.000
4116.000
4118.000
4116.000
4118.000
967
Components front and rear
Trim panels (sides)
Base/plinth trim, modular SO
Accessories
Lock systems
Standard double-bit lock insert may be exchanged for lock inserts, type F, see page 956, and comfort handle, see page 947 – 948.
Delivery times available on request.
Cable glands IP 68
Cable glands made from
polyamide or brass,
Model No. see page 1054.
Punched rail
25 x 38 mm,
Model No. see page 996.
Accessories Page 890 Cable entry From page 1045
Rittal Catalogue 32/Industrial Enclosures
151
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
Prepared for EX pressurisation
F
T
H
G
B
B
Baying systems TS 8
1.3
With this empty enclosure and
an external overpressure controller such as those offered by
STAHL, Bartec or Gönnheimer,
conventional operating materials may be used in explosion
hazard areas. To this end, a permanent overpressure is applied
to the enclosure which prevents
the ingress of potentially explosive atmospheres.
Empty enclosure, prepared for
pressurisation, ensures efficient
operation thanks to low leakage
rates of approximately 20 l/min,
at 2 mbar overpressure.
Ex overpressure enclosures
must be constructed and operated in conformity with standards DIN EN 60 079-0 and
DIN EN 60 079-2.
For populated enclosures of protection type “p”, in accordance
with Directive 94/9 EC, type testing certification from a designated office is required.
Design:
● Base as for roof
● Reinforced:
− Rear panel
− Side panels
− Door with additional cams
top and bottom, r/h hinge,
l/h hinge on request
Protection category:
IP 55 to EN 60 529/09.2000
complies with NEMA 12
Surface finish:
Sheet steel:
Enclosure frame: Dipcoatprimed door, roof, base, side
panels and rear panel: Dipcoatprimed, powder-coated in textured RAL 7035 on the outside
Mounting plate: Zinc-plated
Supply includes:
Enclosure frame with door (with
additional cam top and bottom),
roof/base plate, rear panel, side
panels, mounting plate.
Stainless steel:
Enclosure frame: Uncoated
Door, side panels, roof, base/
plinth, and rear panel:
Brushed, grain size 400
Mounting plate: Zinc-plated
Rittal service:
Enclosures for baying
available on request.
Width (B) mm
600
800
600
800
600
800
1000
600
800
600
–
Height (H) mm
1400
1400
1600
1600
1800
1800
1800
1800
1800
1800
–
Depth (T) mm
500
500
500
500
400
400
400
500
500
600
–
Mounting plate width (F) mm
499
699
499
699
499
699
899
499
699
499
–
Mounting plate height (G) mm
1296
1296
1496
1496
1696
1696
1696
1696
1696
1696
–
8645.560
8845.560
8665.560
8865.560
8684.560
8884.560
8084.560
8685.560
8885.560
8686.560
–
Model No. TS sheet steel
Width (B) mm
800
600
800
600
800
600
800
600
800
600
800
Height (H) mm
1800
2000
2000
2000
2000
2000
2000
2000
2000
2200
2200
Depth (T) mm
600
400
400
500
500
600
600
800
800
600
600
Mounting plate width (F) mm
699
499
699
499
699
499
699
499
699
499
699
Mounting plate height (G) mm
1696
1896
1896
1896
1896
1896
1896
1896
1896
2096
2096
8886.560
8604.560
8804.560
8605.560
8805.560
8606.560
8806.560
8608.560
8808.560
8626.560
8826.560
Width (B) mm
800
1000
600
800
600
600
800
800
–
–
–
Height (H) mm
1800
1800
1800
1800
1800
2000
2000
2000
–
–
–
Depth (T) mm
400
400
500
500
600
600
600
800
–
–
–
Mounting plate width (F) mm
699
899
499
699
499
499
699
699
–
–
–
Mounting plate height (G) mm
1696
1696
1696
1696
1696
1896
1896
1896
–
–
–
Model No. TS stainless steel
8454.660
8461.660
8457.660
8455.660
8458.660
8452.660
8450.660
8460.660
–
–
–
Model No. TS sheet steel
Delivery times available on request.
Accessories Page 890 Cable entry From page 1045
152
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Baying systems TS 8
For areas at risk from earthquakes
2
4
TS 8 for earthquake zone 1, 2
and 3 to Bellcore
TS 8806.500:
W x H x D 800 x 2000 x 600 mm
TS 8 for earthquake zone 4
to Bellcore
TS 8806.500:
W x H x D 800 x 2000 x 600 mm
With base/plinth (base/plinth
components front and rear and
base/plinth trim, side,
see page 893), 100 mm high
with a weight load of 125 kg
spread evenly over the mounting plate.
Fitted with:
● Earthquake kit and
● Earthquake base/plinth,
see page 153,
Note:
These versions have been
tested and meet the requirements to Telcordia GR 63-CORE.
They should be seen as a comparative variable to the customer’s own plant, since the certification of empty enclosures is
not possible.
1
Earthquake kit
Material:
Sheet steel
3
Surface finish:
Zinc-plated, passivated
Supply includes:
with weight load of 450 kg
distributed evenly over the
mounting plate.
1.3
Rittal service:
● Mounting on the enclosure
on request.
For enclosures
WxHxD
mm
Packs of
800 x 2000 x 600
1
8613.860
600 x 2000 x 600
1
8613.6601)
600 x 2000 x 400
1
8613.6401)
1) Delivery
B
Baying systems TS 8
3
Model No. TS
times available on request.
1 2 side reinforcements, bottom
2 2 bracing struts each, sides
3 8 gusset plates
4 Mounting plate attachment and reinforcement
2
including assembly parts
4
Earthquake base/plinth
Height 100 mm
Material:
Sheet steel
Corner pieces: 5 mm
Trim panels: 2 mm
Surface finish:
Powder-coated in RAL 7022
For enclosures
WxD
mm
Packs of
800 x 600
1
8601.860
600 x 600
1
8601.6601)
600 x 400
1
8601.6401)
1) Delivery
Model No. TS
times available on request.
Supply includes:
1 set =
● 4 corner pieces
● 2 depth stays
● 1 trim panel each front and rear
fully assembled.
Accessories Page 890 Base/plinth Page 892
Rittal Catalogue 32/Industrial Enclosures
153
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial Enclosures
Large enclosures
1.3 Baying system TS 8
Spray-finished Page 138 – 147
Stainless steel Page 322
B1
B7
T7
35
35
55
46
3.5
2.5
C
64.5
i.L. T3
60
2.5
60
B1
B7
30
T6
2
B6
B6
B6
17
H5
G
i.L. H3
Ø6
51
Ø9
32.5
25
H9
71
Ø 4.6
Ø9
H1
4 x 25 (= 100)
4 x 25 (= 100)
H9
71
i.L. B5
H2
71
i.L. B5
H4
H8
H6
i.L. H7
H4
71
H8
H6
i.L. H7
i.L. B5
62.5
i.L. T5
44
4.5
22
M6
96
22
96
M6
T4
T1
18
i.L. T3
78.5
i.L. B8
1 Does not apply to
6
30
65
46.5
M12
15
30
65
B2
i.L. B8
Ø1
M12
i.L. B3
46.5
30
65
18
78.5
Note:
With fitted side panels, the
overall width (B1) is increased
by 9 mm. Between bayed enclosures, allow 3 mm for the seal.
i.L. B3
B2
Base/plinth mounting: B4 x T2
TS 8880.500/TS 8881.500
15
i.L. B8
16
49
F
78.5
46.5
Ø
30
1
49
T1
49
F
61
B4
30
T2
T2
49
78.5
61
46.5
30
i.L. T3
30
30
65
61
B4
61
T1
Industrial Enclosures
1.
i.L. = Clearance width
Base/plinth mounting: B4 x T2
Double-door
Model No. TS
Width dimensions mm
Spray- Stainless
B1
finished
steel
B2
B3
B4
B5 B6
Height dimensions mm
B7
B8
H1
H2
H3
H4
H5
H6
H7
Mounting
plates mm
Depth dimensions mm
H8
H9
T1 T2 T3 T4 T5
T6
T7
F
G
8215.500
–
1197 1192 1112 1075 455 475 1135 500 1205 1197 1112 1177.5 1075 1050 1030 1000 611 505 375 412 468 340 130 – 455 435 1099 1096
8245.500
–
1197 1192 1112 1075 455 475 1135 500 1405 1397 1312 1377.5 1275 1250 1230 1200 711 505 375 412 468 340 130 – 455 435 1099 1296
8080.500
–
997 992 912 875 355 375 935 400 1805 1797 1712 1777.5 1675 1650 1630 1600 911 405 275 312 368 240 130 – 355 335 899 1696
8284.500 8456.X00 1197 1192 1112 1075 455 475 1135 500 1805 1797 1712 1777.5 1675 1650 1630 1600 911 405 275 312 368 240 130 – 355 335 1099 1696
8880.500
–
797 792 712 675 255 275 735 640 1805 1797 1712 1777.5 1675 1650 1630 1600 911 505 375 412 468 340 130 – 455 435 699 1696
8285.500 8453.X00 1197 1192 1112 1075 455 475 1135 500 1805 1797 1712 1777.5 1675 1650 1630 1600 911 505 375 412 468 340 130 – 455 435 1099 1696
8881.500
–
797 792 712 675 255 275 735 640 1805 1797 1712 1777.5 1675 1650 1630 1600 911 605 475 512 568 440 130 – 555 535 699 1696
8286.500
–
1197 1192 1112 1075 455 475 1135 500 1805 1797 1712 1777.5 1675 1650 1630 1600 911 605 475 512 568 440 130 – 555 535 1099 1696
8004.500
–
997 992 912 875 355 375 935 400 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 405 275 312 368 240 130 – 355 335 899 1896
8204.500
–
1197 1192 1112 1075 455 475 1135 500 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 405 275 312 368 240 130 – 355 335 1099 1896
8005.500
–
997 992 912 875 355 375 935 400 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 505 375 412 468 340 130 – 455 435 899 1896
8205.500
–
1197 1192 1112 1075 455 475 1135 500 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 505 375 412 468 340 130 – 455 435 1099 1896
8006.500
–
997 992 912 875 355 375 935 400 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 605 475 512 568 440 130 – 555 535 899 1896
8206.500 8451.X00 1197 1192 1112 1075 455 475 1135 500 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 605 475 512 568 440 130 – 555 535 1099 1896
8208.500
–
1197 1192 1112 1075 455 475 1135 500 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 805 675 712 768 640 130 – 755 735 1099 1896
8226.500
–
1197 1192 1112 1075 455 475 1135 500 2205 2197 2112 2177.5 2075 2050 2030 2000 1111 605 475 512 568 440 130 – 555 535 1099 2096
8265.500
–
1197 1192 1112 1075 455 475 1135 500 1605 1597 1512 1577.5 1475 1450 1430 1400 811 505 375 412 468 340 130 – 455 435 1099 1496
1184
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial Enclosures
Large enclosures
Enclosure
Cross-sections
vertical
F
B1 =
B2 =
B3 =
B4 =
23
25
4.5
48
24.5
42.5
12.5
42
73
25
12.5
24.5
i.L. (T3)
42.5
6.5
23
17
23
B5 =
B6 =
i.L. (B3)
B7 =
B8 =
4
H1 = Overall height
H2 = Height of rear panel
H3 = Clearance between the enclosure frame
H4 = Height of door
H5 = Section length of system punchings
H6 = Distance between axes of tubular door
frame holes
H7 = Clearance between the tubular door frame
H8 = Distance between the fastening bolts
of the tubular door frame
H9 = Distance from base to centre of lock
horizontal
G
11.5
20
25
4
10.5
12.5
12.5
42.5
42.5
12.5
i.L. (H3)
4.5
i.L. (B3/T3)
Overall width
Width of door
Clearance between the enclosure frames
Section length of system punchings/
hole spacing base/plinth attachment
Clearance between the tubular door frames
Distance between axes of tubular door
frame holes
Distance between the lifting eyes
Clearance in the base opening
C
1.
Industrial Enclosures
Mounting plate
T1 = Overall depth
T2 = Section length of system punchings/
hole spacing
T3 = Clearance between the enclosure frames
T4 = Depth of base frame
T5 = Clearance of base opening
T6 = Possible mounting depth (mounting plate
assembly) depth-adjustable on a 25 mm
pitch pattern
T7 = Centre of lifting eye to centre of lifting eye
i.L. = Clearance width
Mounting plate
F = Overall width
G = Overall height
Single-door
Model No. TS
Width dimensions mm
Spray- Stainless
B1
finished
steel
B2
B3
B4
B5 B6
Height dimensions mm
B7
B8
H1
H2
H3
H4
H5
H6
H7
Mounting
plates mm
Depth dimensions mm
H8
H9
T1 T2 T3 T4 T5
T6
T7
F
G
8615.500
–
597 592 512 475 455 475 535 440 1205 1197 1112 1177.5 1075 1050 1030 1000 611 505 375 412 468 340 130 – 455 435 499 1096
8815.500
–
797 792 712 675 655 675 735 640 1205 1197 1112 1177.5 1075 1050 1030 1000 611 505 375 412 468 340 130 – 455 435 699 1096
8645.500
–
597 592 512 475 455 475 535 440 1405 1397 1312 1377.5 1275 1250 1230 1200 711 505 375 412 468 340 130 – 455 435 499 1296
8845.500
–
797 792 712 675 655 675 735 640 1405 1397 1312 1377.5 1275 1250 1230 1200 711 505 375 412 468 340 130 – 455 435 499 1296
8684.500
–
597 592 512 475 455 475 535 440 1805 1797 1712 1777.5 1675 1650 1630 1600 911 405 275 312 368 240 130 – 355 335 499 1696
8884.500 8454.X00 797 792 712 675 655 675 735 640 1805 1797 1712 1777.5 1675 1650 1630 1600 911 405 275 312 368 240 130 – 355 335 699 1696
8084.500
–
997 992 912 875 855 875 935 840 1805 1797 1712 1777.5 1675 1650 1630 1600 911 405 275 312 368 240 130 – 355 335 899 1696
8485.510
–
397 392 312 275 255 275 335 240 1805 1797 1712 1777.5 1675 1650 1630 1600 911 505 375 412 468 340 130 – 455 435
–
–
8685.500 8457.X00 597 592 512 475 455 475 535 440 1805 1797 1712 1777.5 1675 1650 1630 1600 911 505 375 412 468 340 130 – 455 435 499 1696
8885.500 8455.X00 797 792 712 675 655 675 735 640 1805 1797 1712 1777.5 1675 1650 1630 1600 911 505 375 412 468 340 130 – 455 435 699 1696
8486.510
–
397 392 312 275 255 275 335 240 1805 1797 1712 1777.5 1675 1650 1630 1600 911 605 475 512 568 440 130 – 555 535
8686.500
–
597 592 512 475 455 475 535 440 1805 1797 1712 1777.5 1675 1650 1630 1600 911 605 475 512 568 440 130 – 555 535 499 1696
8886.500
–
797 792 712 675 655 675 735 640 1805 1797 1712 1777.5 1675 1650 1630 1600 911 605 475 512 568 440 130 – 555 535 699 1696
8604.500
–
597 592 512 475 455 475 535 440 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 405 275 312 368 240 130 – 355 335 499 1896
8804.500
–
797 792 712 675 655 675 735 640 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 405 275 312 368 240 130 – 355 335 699 1896
8405.510
–
397 392 312 275 255 275 335 240 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 505 375 412 468 340 130 – 455 435
8605.500
–
597 592 512 475 455 475 535 440 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 505 375 412 468 340 130 – 455 435 499 1896
8805.500
–
797 792 712 675 655 675 735 640 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 505 375 412 468 340 130 – 455 435 699 1896
8406.510
–
397 392 312 275 255 275 335 240 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 605 475 512 568 440 130 – 555 535
–
–
–
–
–
–
8606.500 8452.X00 597 592 512 475 455 475 535 440 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 605 475 512 568 440 130 – 555 535 499 1896
8806.500 8450.X00 797 792 712 675 655 675 735 640 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 605 475 512 568 440 130 – 555 535 699 1896
8608.500
–
597 592 512 475 455 475 535 440 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 805 675 712 768 640 130 – 755 735 499 1896
8808.500
–
797 792 712 675 655 675 735 640 2005 1997 1912 1977.5 1875 1850 1830 1800 1011 805 675 712 768 640 130 – 755 735 699 1896
8626.500
–
597 592 512 475 455 475 535 440 2205 2197 2112 2177.5 2075 2050 2030 2000 1111 605 475 512 568 440 130 – 555 535 499 2096
8826.500
–
797 792 712 675 655 675 735 640 2205 2197 2112 2177.5 2075 2050 2030 2000 1111 605 475 512 568 440 130 – 555 535 699 2096
8665.500
–
597 592 512 475 455 475 535 440 1605 1597 1512 1577.5 1475 1450 1430 1400 811 505 375 412 468 340 130 – 455 435 499 1496
8865.500
–
797 792 712 675 655 675 735 640 1605 1597 1512 1577.5 1475 1450 1430 1400 811 505 375 412 468 340 130 – 455 435 699 1496
Rittal Catalogue 32/Industrial Enclosures
1185
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial Enclosures
Large enclosures
1.3 Baying system TS 8
Electronic enclosures Page 148
465
535/735
1466.6 (33 HE)/1866.9 (42 HE)
1512/1912
1605/2005
43
63
452
53
486
HE = U
592
622/822
512/712
512
592
1.3 Baying system TS 8
Cross-sections
For modular front design Page 149
vertical
i.L.
25
42.5
42.5
25
12.5
4.5
12.5
i.L. 512
475
601.5
i.L.
30
30
65
30
6.5
61
42.5
12.5
77
46
3.5
475/675
46.5
61
i.L. 512
535/735
horizontal
31
4
11.5
Ø1
6
20
4.5
4
10.5
12.5
i.L.
12.5
42.5
i.L.
1850
i.L. = Clearance width
i.L. 440
77
44
4.5
25
1997
i.L. 1912
2005
25
597/797
42.5
512/712
42.5
30
65
M12
12.5
535
18
35
597/797
60
Industrial Enclosures
1.
9.5
C
31.75
44.45
7.6
452
568
601.5
1186
Rittal Catalogue 32/Industrial Enclosures
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Industrial Enclosures
Large enclosures
1.3 Baying system TS 8
For isolator door locking Page 150
35
797
Detail X
35
T7
i.L. T3
77
3.5
46
2.5
60
735
Industrial Enclosures
12.7
H5
i.L. H3
H1
H2
H4
i.L. 455
1.
119.1
17
71
H8
H6
475
25.4 22.2 25.4
2
T6
X
i.L. H7
C
14.3
12.5
55
340.5
90.5
42.5
7.1
93
H9
4 x 25
(= 100)
1
4.5
22
96
M6
44
51
Ø9
35.5
25
Ø 4.6
1 Only for TS 8906.500
i.L. T5
T4
T1
49
i.L. 640
78.5
18
i.L. T3
T2
699
78.5
Ø1
i.L. = Clearance width
46.5
30
65
30
30
49
T1
61
675
61
6
i.L. 712
592
192
15
46.5
30
65
M12
Enclosure
H1 = Overall height
H2 = Height of rear panel
H3 = Clearance between the enclosure
frame
H4 = Height of door and trim panel
H5 = Section length of system punchings
H6 = Distance between axes of the tubular
door frame rows of holes
H7 = Clearance between the tubular door
frame
H8 = Distance between the fastening bolts
of the tubular door frame
H9 = Distance from base to centre of lock
Model No. TS
Note:
The cut-outs in the right-hand trim piece are
suitable for the following isolator actuators:
Allen Bradley 1494 V-H11, Square
D9422A1, ITE Siemens1) Max-Flex series/F
HOH, General Electric TDA Type 1 and 2,
Moeller NZM-XSHGVR12-NA.
T1 = Overall depth
T2 = Section length of system punchings/
distance between holes of base/
plinth attachment
T3 = Clearance between enclosure frames
T4 = Depth of base frame
T5 = Clearance of base opening
T6 = Possible mounting depth
(mounting plate assembly)
T7 = Centre of lifting eye to centre
of lifting eye
1)
Height dimensions mm
Available in USA only.
Depth dimensions mm
H1
H2
H3
H4
H5
H6
H7
H8
H9
T1
T2
T3
T4
T5
T6
T7
8984.500
1805
1797
1712
1754
1675
1650
1630
1600
911
405
275
312
368
240
130 – 355
335
8985.500
1805
1797
1712
1775
1675
1650
1630
1600
911
505
375
412
468
340
130 – 455
435
8905.500
2005
1997
1912
1975
1875
1850
1830
1800
1011
505
375
412
468
340
130 – 455
435
8906.500
2005
1997
1912
1975
1875
1850
1830
1800
1011
605
475
512
568
440
130 – 555
535
Rittal Catalogue 32/Industrial Enclosures
1187
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com