Installation/Operating Instructions
Phantom Video Projector Lift for Tabletop Installation by Draper
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your
distributor to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
Caution
1 Read instructions completely before proceeding.
2 Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
3 Do not obstruct operation of the lift with fingers or any other object.
Serious injury or damage could result.
4 Before putting this unit into regular use, the Obstruction Shutoff
sensitivity must be adjusted using a GUI program available for download
at www.draperinc.com/go/Phantom.htm. A Windows PC or laptop is
required to operate the GUI program.
5 Closure panel or top of unit must be unobstructed to permit proper
operation.
6 Unit must be installed level (use a carpenter’s level).
7 Unit operates on 24V DC.
Note: Unit has been thoroughly inspected and tested at factory and found
to be operating properly prior to shipment.
Planning
1 Based on screen location and projector specifications, determine proper
position for projector installation.
2 Confirm that there is adequate space for installation and operation.
3 Arrange to provide service access to the unit.
4 Total lifting capacity of lift is 26 lbs (11.8 kg), including projector and
closure panel.
5 The Tabletop Phantom comes with an Obstruction Shutoff feature. After
installation the sensitivity of this feature must be adjusted using a GUI
program (for Windows PC or laptop) and a Serial Programming/Control Kit
(included).
As Soon As Phantom Projector Lift Arrives
1 Open carton and inspect for damage.
2 Locate the following parts:
A. The unit itself
B. Controls
C. Serial Programming/Control kit
D. Any optional equipment
3 Test unit before installing.
4 Top of unit must be unobstructed after installation.
Important Safety Instructions
1 Do not use this apparatus near water or moisture—for example, in a wet
basement, near a swimming pool, etc.
2 Do not block any ventilation openings. Install in accordance with the manufac turer’s instructions.
3 Do not install near any heat sources, including radiators, heat registers, stoves,
or other equipment (including amplifiers) that produces heat.
4 Only use attachments/accessories specified by the manufacturer.
5 Unplug the apparatus during lightning storms or when unused for long periods
of time.
6 Refer all servicing to qualified personnel. Servicing is required when the ap paratus has been damaged in any way, including but not limited to: power
supply cord or plug cut, frayed or otherwise damaged; liquid spilled/objects
fallen into the unit; exposure to rain or moisture; unit not operating normally; or
unit has been dropped.
Caution: Beware
of pinch point.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK. DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
7 This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock. Where in a manufacturer’s service documentation, for
example in circuit diagrams or lists of components, a symbol “ ” is used to
indicate that a specific component shall be replaced only by the component
specified in that documentation for safety reasons.
8 When apparatus operation and installation instructions contain instructions for
use by service personnel, such instructions shall be separate in format from
other instructions and preceded by the word “CAUTION” and the following
or the equivalent. “These servicing instructions are for use by qualified service
personnel only: To reduce the risk of electric shock do not perform any servic ing other than that contained in the operating instructions unless you are quali fied to do so.”
9 The unit shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the unit.
Copyright © 2015 Draper Inc.
Form Phantom-Table_Inst15
Printed in U.S.A.
View from below
Installing Unit
The Phantom is provided with four (4) mounting points.
All installations should observe the following guidelines:
1 Installer must ensure that all fasteners and supports are of adequate
strength to securely support Phantom and projector. It is recommended
that hardware structure be able to hold at least four times the combined
weight of the lift and projector.
2 Fastening methods must be suitable for mounting surface, and securely
anchored so vibration or abusive pulling on unit will not weaken installation.
3 Top of unit must be unobstructed after installation.
If you encounter any difficulties installing or servicing your Phantom projector lift, call
your dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.
Outside the United States, fax (765) 987-1689.
Phantom Video Projector Lift for Tabletop Installation by Draper, Inc.
Electrical Connections
Unit operates on 24V DC.
The Phantom is shipped closed.
Please note: Make sure electrical supply has been disconnected before
attempting to connect Phantom to electricity.
Connections should be made in accordance with wiring diagram, and wiring
should comply with national and local electrical codes. All operating switches
should be “off” before power is connected.
110V or 220V AC for projector must be supplied by others. Phantom should
be operated and checked prior to installing projector.
Phantom Tabletop Operation
Open
Operation
Unit is automatically supplied with a DC Motor Control and a three-button
up-stop-down wall switch. When unit is first operated, be cautious! If unit fails
to operate when the “up” button is pressed, press “off” and recheck electrical
connections before proceeding. Cycle unit down and up several times to
confirm satisfactory operation.
DC Motor Control (CE Approved)—In addition to standard wall switch and
Obstruction Shutoff adjustment, allows optional remote control, RS232 or
Ethernet connection. Included as standard.
Optional Infrared or Radio Frequency Remote Control (CE Approved)—A
three-button transmitter is provided, with “up”, “down”, and “stop” buttons.
Unit starts opens or closes when appropriate button is pressed, and may be
stopped by pressing “off” button. When using RF or IR control, a three-button
up-stop-down wall switch is also recommended and optionally available.
Optional RS232 (CE Approved)—Serial communication optionally available
with wall switches, RF or IR remote.
Optional Ethernet (Not CE Approved)—Network communication optionally
available with wall switches, RF or IR remote.
Closed
Views from top
Phantom Tabletop—Dimensions
231/8"/58.7 cm
(305/8"/77.8 cm)
1/2"/1.27
cm
157/8"/40.3 cm
(193/4"/50.2 cm)
259/16"/65 cm
(323/4"/83.2 cm)
11/4"/3.2 cm
(11/16"/2.7 cm)
1413/16"/37.6 cm
(183/4"/47.6 cm)
81/8"/20.6 cm
(81/8"/20.6 cm)
5"/12.6 cm
(5"/12.6 cm)
15"/38.1 cm
(1815/16"/48.1 cm)
www.draperinc.com
(765) 987-7999
163/16"/41.1 cm
(201/4"/51.4 cm)
Please note:
non-bracketed
dimensions
are for Model
A; bracketed
dimensions are
for Model B.
page 2 of 4
Phantom Video Projector Lift for Tabletop Installation by Draper, Inc.
page 3 of 4
Projector Installation
The Phantom video projector lift uses the Skyhook projector mount system.
The parts kit contains:
-Two long skyhook arms
-Four short skyhook arms
-Four M3, four M4, four M5 & four M6 mounting bolts (30 mm)
-Four spacers (1/2" [12.7], 5/8" [15.875], 3/4" [19.05], 7/8" [22.225 mm])
1 Determine which size mounting bolts suit your projector, and set others
aside. They are no longer required. If your projector has only three
mounting holes, set aside one of the skyhook arms.
2 Assemble the universal mount (see diagram at right) using arms
appropriate to projector. Spread out the arms so each end is over one of
the mounting holes.
3 Connect universal mount to Projector. Fit the 1/2" (12.7 mm) spacer under
the lowest arm, the 5/8" (15.875 mm) under the next arm and so on. If the
projector base is uneven, you may use combinations of spacers and arms
to ensure the triangular plate is horizontal.
4 Do not tighten any bolts yet.
5 Move the position of the triangular plate over the center of the projector,
with the edge with the two holes towards the front (lens).
6 Tighten the mounting bolts. The projector and universal mount are ready to
be inserted into the Phantom. Please note the projector will be in the
upright, or desktop, mode.
7 First ensure that the Phantom is operating correctly, and that the projector
cables are properly secured. Open the Phantom and insert the triangular
projector plate into the slot in the rear of the Phantom. Attach it at the front
using the supplied ¼" (6.35 mm)-20 bolts and springs.
8 These bolts will also give you Roll and Tilt adjustment to align your image
on the screen, while the center 5/16" (8 mm) bolt provides Yaw adjustment.
The springs will ensure that the projector is held still during motion. Do not
install the projector plate without springs.
Minimum: 3" (7.6 cm)
Maximum: 13" (33 cm)
In order to use the
skyhook universal
mount, the mounting
holes in your projector
must be located within
the area indicated by
the circle.
Cable Management
A cable exit hole is pre-drilled in the bottom panel. Make sure to leave enough
slack in the cable to account for the motion of the Phantom during operation.
Closure Panel Installation (by others)
Yaw
Roll
Tilt
Caution: Beware of pinch point.
Rough Opening Size for Closure Panel
The closure panel is not included with the Phantom; one needs to be
custom made, and should be the following sizes.
Phantom A — ½" x 1511/16" x 1511/16"
Phantom B — ½" x 195/8" x 195/8"
A minimum 3/16" reveal or gap should be left surrounding the closure panel.
Minimum rough opening sizes:
Phantom A — 157/8" x 157/8"
Phantom B — 1913/16" x 1913/16"
www.draperinc.com
The Phantom comes with four 1" sections of hook & loop attachment strips
for attachment in all four corners of a closure panel (provided by others).
Please note the following when installing a closure panel:
1 Please use the hook & loop attachment system for attaching the closure
panel to the Phantom. This provides a safety back-up in case fingers or
other objects are caught between the closure and the tabletop when the
closure closes: The hook & loop attachment strips will separate, leaving the
closure panel loose and preventing pinching or injury.
Caution: If you permanently attach the closure panel to the Phantom
using screws or other means, there is a danger of pinching, injuries to
fingers and damage to other objects.
2 Remember that the total weight of the projector, bracket and closure panel
cannot exceed 26 lbs (11.8 kg).
3 Be sure to leave enough space between the edge of the closure and the
surrounding tabletop to allow the closure edge to clear the table during
opening and closing of the closure. There should be a minimum gap of 3/16".
Making your own closure panel to match surround cabinet or furniture:
Phantom A — ½" thick x 1511/16" x 1511/16"
Phantom B — ½" thick x 195/8" x 195/8"
Custom panel should be same size. The weight of the panel needs to be
factored in for the total weight. See 2 above. Hook & loop attachment strips
must also be used to attach custom closure to the Phantom (see 1 above).
(765) 987-7999
Correct
Incorrect
Phantom Video Projector Lift for Tabletop Installation by Draper, Inc.
6 Position, 6 pin
Modular Connector
(RJ-25 a.k.a ‘6P6C’)
page 4 of 4
6 Position, 6 pin
Modular Connector
(RJ-25 a.k.a ‘6P6C’)
PIN 6
Adjusting Obstruction Shutoff Sensitivity
PIN 6
FUNCTION
R CLOCK
RQ
COMMON
+5VDC
5VDC
R DA
RQ
D TA
RP DA
D TA
+12VDC
12VDC
PIN 1
PIN #
1
2
3
4
5
6
PIN 1
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
The Obstruction Shutoff feature stops the unit if its operation is obstructed. For this
Please Note:
feature to work properly, its sensitivity must be adjusted.
Cable used to connect to the Eye jack must be electrically straight
This is the final stage of installation. Projector and closure panel must be installed
6-conductor modular cable (RJ25). This means colors do not cross
before adjusting the sensitivity of this feature, and it must be reset if changes are made over: blue leads to blue, green to green, etc. (see diagram below).
in the projector or closure panel in the future.
* Please Note: To adjust this feature, you must use the Serial Programming/
Control Kit (provided). This feature is used to adjust the unit's sensitivity to an
obstruction before it stops the lift from closing.
1 Download Obstruction Shutoff Adjustment GUI Program from
www.draperinc.com/go/Phantom.htm and install on your PC/Laptop.
2 Connect your PC/Laptop to the Phantom, as shown in figure below.
6 Position, 4 pin
Modular Connector
(RJ-14 a.k.a ‘6P4C’)
Tab facing
away (down)
Tab facing
away (down)
6 Position, 4 pin
Modular Connector
(RJ-14 a.k.a ‘6P4C’)
Tab facing
away (down)
6 Position, 4 pin
Modular Connector
(RJ-14 a.k.a ‘6P4C’)
Tab facing
away (down)
PIN #
1
2
3
4
5
6
FUNCTION
emp
m tty
COMMON
+5VDC
5VDC
unused
d
RP DA
D TA
emp
m tty
6 Position, 6 pin
Modular Connector
(RJ-25 a.k.a ‘6P6C’)
Tab facing
away (down)
6 Position, 4 pin
Modular Connector
(RJ-14 a.k.a ‘6P4C’)
3 Launch the GUI program on your PC/Laptop so that you see the diagram to the right.
Tab facing
4 Operate the Phantom "open" and "closed."
away (down)
5 Adjust the sensitivity of the "Open" function. This will set how much weight it takes to keep the
unit from opening. Starting with the "Low Threshold" button beneath the "Open Direction"
heading in the GUI window, use the "Threshold" buttons until the unit does not open (use the
remote to try and open after each adjustment—if it opens, close it and go to the next button).
Then use "Nudge Stall Current Higher (Less Sensitive)" button until the unit opens normally to
see result. This button on the GUI may have to be pressed many times.
Please Note: When you press a program button on the GUI, you must watch for the
"Program Light" on the DC Motor Control to light up to verify that it received the command.
6 Repeat step 4 for the "Close" function, using the buttons beneath the "Close Direction" heading.
This will set how much pressure the unit will exert on an obstruction before it stops operating.
Caution: Once the sensitivity is set as outlined above so that the unit operates, it can be
adjusted according to the situation and preferences of the installer/end user. While
adjusting the "closing" sensitivity, DO NOT use your hands, fingers or other body parts to
test the setting. If the Obstruction Shutoff is engaged, the motor can be reactivated by
pressing the "Up" or "Down" button on the control switch.
Please Note: The unit may stall if the motor becomes overheated during this procedure,
causing a false sensitivity setting. Once the sensitivity has been set, leave unit to cool for several minutes, then test. You may need to set the
sensitivity more than once.
Phantom Tabletop Wiring Diagram
RD
DC CONVERTER
BK
OUTPUT: 24 VDC
2.5 Amp
BN
BN
BL
BL
LINEAR ACTUATOR
(220V Only)
24 VDC
DC Motor Control
AUX PORT- For connecting multiple controls together.
( up to six total-connect from AUX to Eye).
DASHED LINES INDICATE
WIRES PROVIDED BY INSTALLER
EYE PORT- For IR EYE; RF Receiver or LED
Switch. If more than one of these three is
used with control, a splitter is required.
DOWN - BLACK
COM - WHITE
UP - RED
www.draperinc.com
(765) 987-7999
STOP
WALL SWITCH
3 BUTTON
PIN 5
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
Correct
Tab fa
away (
PIN 2
FUNCTION
R CLOCK
RQ
COMMON
+5VDC
5VDC
R DA
RQ
D TA
RP DA
D TA
+12VDC
12VDC
Tab facing
away (down)
PIN 6
PIN #
1
2
3
4
5
6
Tab facing
away (down)
Tab facing
away (down)
PIN 1
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
PIN 5
Tab facing
away (down)
Tab facing
away (down)
PIN 2
o
2
7 vsimple
R2gyDmade
nol
h
Tec
SYS 6
SYS 71 SYS 2
SYS
MAIN
Tab facing
away (down)
PIN 6
FUNCTION
emp
m tty
COMMON
+5VDC
5VDC
unused
d
RP DA
D TA
emp
m tty
6 Position, 6 pin
Modular Connector
(RJ-25 a.k.a ‘6P6C’)
PIN 1
PIN #
1
2
3
4
5
6
PIN 5
To
PC
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
Tab facing
away (down)
Incorrect
6 Position, 6 pin
Modular Connector
(RJ-25 a.k.a ‘6P6C’)
PIN 2
2
7 vsimple
R2yDmade
olog
SYS 4
SYS 53 RS-232
S
SYS 6
SYS 71 SYS 2 SY
SYS
MAIN
FUNCTION
R CLOCK
RQ
COMMON
+5VDC
5VDC
R DA
RQ
D TA
RP DA
D TA
+12VDC
12VDC
PIN 6
RS232
Adapter
PIN #
1
2
3
4
5
6
PIN 1
R2D7
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
PIN 5
Tab facing
away (down)
Tab facing
away (down)
PIN 2
PIN 5
FUNCTION
emp
m tty
COMMON
+5VDC
5VDC
unused
d
RP DA
D TA
emp
m tty
Tab facing
away (down)
Tab facing
away (down)
Correct
hn
Tec
DC
Motor
Eye Control
Port
Prog
Light
PIN #
1
2
3
4
5
6
6 Position, 4 pin
Modular Connector
(RJ-14 a.k.a ‘6P4C’)
PIN 2
COLOR
WHITE
BLA
L CK
RED
GREEN
YELLOW
BLUE
Tab facing
away (down)
Tab fa
away (d