NOVA24
SURFACE
W W W . L U M E N W E R X . C O M
PROJECT:
APPROVED BY:
SIGNATURE:
Shown with a Nova flat lens
Shown with a Nova Slope lens
TYPE
QTY
DESCRIPTION
Nova is an efficient architectural LED troffer with a distinctive luminous shielding that distributes gentle
brightness from the sides of its central optical element. Using advanced LED engines, Nova provides
highly efficient illumination and offers comprehensive ceiling, electrical, and controls options in 2x2, 1x4,
and 2x4 sizes. Nova is available with both Flat and Slope side diffusers.
See separate spec sheets for other available mountings.
ORDER GUIDE
24
PMO
HLO
LUMINAIRE ID
SIZE
CENTER OPTICS
SIDE OPTICS
LIGHT SOURCE
NUMBER OF LAMPS
VOLTAGE
NOVSF - nova
24 - 2'x4'
PMO - Precision Micro-Prism
HLO - High-Efficiency Lambertian
T5 - T5 lamp
1 - 1 lamp
120 - 120V
Optic
Optic
T5HO - T5HO lamp
2 - 2 lamps
277 - 277V
T8 - T8 lamp
3 - 3 lamps
UNV - 120V-277V
surface flat
NOVSS - nova
347 - 347V
surface slope
SUR
BALLAST
ELECTRICAL
MOUNTING
FINISH
CONTROLS
OPTIONS
RS - rapid start
1 - 1 circuit
SUR - surface mount kit
W - matte white
ONBOARD
FU - fuse
D - dimming 0-10V
2 - 2 circuits
CF# - custom finish
OMS - Motion Sensor & power pack
CU - custom
ST - step dimming
+EB - emergency battery pack
specify RAL#
ODS - Daylight Sensor & controller
DA - dali
+EM - emergency light circuit
WIRELESS
LHL - Lutron Hi-Lume 3D
+NL - night light circuit
EWC - EnOcean Wireless Controller
LEH - Lutron EcoSystem H
+GTD - generator transfer device
LMC - Lutron Motion Controller
+M - master (consult factory)
LDC - Lutron Daylight Controller
+S - satellite (consult factory)
See page 4 for ordering code detailed information
CROSS SECTION
OPTICS
4 1/4"
25 3/8" Mounting kit
NOVSF - nova flat surface mount kit
NOVSS - nova slope
4 1/4"
25 3/8" Mounting kit
NOVSS - nova slope surface mount kit
NOVSF - nova flat
File Name: NOVA24-FLU-SURFACE-SPEC
Page: 1 / 5
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
LumenWerx ULC. reserves the right to change or modify product specifications without notification
July 6, 2016
NOVA24
SURFACE
NOVA FLAT
W W W . L U M E N W E R X . C O M
NOVA SLOPE
1 LAMP
NOVA FLAT - SUR surface
NOVA SLOPE - SUR surface
4 1/4"
4 1/4"
25 3/8" Mounting kit
25 3/8" Mounting kit
2 LAMPS
NOVA FLAT - SUR surface
NOVA SLOPE - SUR surface
4 1/4"
4 1/4"
25 3/8" Mounting kit
25 3/8" Mounting kit
3 LAMPS
NOVA FLAT - SUR surface
NOVA SLOPE - SUR surface
4 1/4"
4 1/4"
25 3/8" Mounting kit
File Name: NOVA24-FLU-SURFACE-SPEC
25 3/8" Mounting kit
Page: 2 / 5
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
LumenWerx ULC. reserves the right to change or modify product specifications without notification
July 6, 2016
NOVA24
SURFACE
W W W . L U M E N W E R X . C O M
ELECTRICAL CIRCUITS
BLK
HOT (CIRCUIT-1)
WHT
GRN
RED
NEUTRAL (CIRCUIT -1)
GROUND (CIRCUIT-1)
UNSWITCHED HOT
1 CIRCUIT
RAPID START 1 Circuit + Emergency Circuit
BLK
WHT
GRN
EM
ORG
WHT
GRN
HOT (CIRCUIT-1)
NEUTRAL (CIRCUIT -1)
GROUND (CIRCUIT-1)
GRN
PPL
GRY
GROUND
DIM(+) 0-10V
DIM(-) 0-10V
1 CIRCUIT
HOT (CIRCUIT-1)
NEUTRAL (CIRCUIT -1)
PPL
GRY
PPL
HOT (CIRCUIT-1)
NEUTRAL (CIRCUIT -1)
GROUND
UNSWITCHED HOT
DIM(+) 0-10V
DIM(-) 0-10V
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
HOT (EM)
NEUTRAL (EM)
GROUND (EM)
BLK
WHT
GRN
ORG
RED
HOT
NEUTRAL
GROUND
HOT DIMMING
UNSWITCHED HOT
PPL
GRY
E1
E2
LUTRON ECOSYSTEM H 1 Circuit
1 CIRCUIT
BLK
HOT (CIRCUIT-1)
NEUTRAL (CIRCUIT -1)
GROUND (CIRCUIT-1)
HOT (CIRCUIT-2)
WHT
GRN
PPL
GRY
HOT
NEUTRAL
GROUND
E1 To EcoSystem
Digital Link
E2
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
LUTRON ECOSYSTEM H 1 Circuit + Emergency Battery
1 CIRCUIT+EB
2 CIRCUITS
To EcoSystem
Digital Link
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
RAPID START 2 Circuits
GRN
RED
GROUND
HOT DIMMING
E1 To EcoSystem
Digital Link
E2
LUTRON Hi-Lume 3D 1 Circuit+ Emergency Battery
NOTE: USE SEPARATE RACEWAY
IN THE FIXTURE FOR EMERGENCY
CIRCUIT
BLK
WHT
HOT
NEUTRAL
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
DIMMING 0-10V 1 Circuit + Emergency Battery
RED
ORG
GRY
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
BLK
WHT
GRN
BLK
WHT
GRN
1 CIRCUIT+EB
1 CIRCUIT+EB
RAPID START 1 Circuit + Emergency Battery
BLK
WHT
LUTRON Hi-Lume 3D 1 Circuit
ECOSYSTEM
HOT (CIRCUIT-1)
NEUTRAL (CIRCUIT -1)
GROUND
1 CIRCUIT+EB
1 CIRCUIT
BLK
WHT
GRN
1 CIRCUIT
DIMMING 0-10V 1 Circuit
RAPID START 1 Circuit
BLK
WHT
GRN
HOT
NEUTRAL
GROUND
RED
UNSWITCHED HOT
E1 To EcoSystem
Digital Link
E2
PPL
GRY
NOTE: MUST FOLLOW WIRE SIZE
AND MAXIMUM LENGTH FOR
DIMMING APPLICATIONS.
File Name: NOVA24-FLU-SURFACE-SPEC
Page: 3 / 5
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
LumenWerx ULC. reserves the right to change or modify product specifications without notification
July 6, 2016
NOVA24
SURFACE
W W W . L U M E N W E R X . C O M
OPTICS
FINISH
CENTER LENS - PRECISION MICRO-PRISM-OPTIC (PMO) - utilizes a specially
Interior reflectors - 95% reflective, matte white
designed catadioptric lens that combines refraction and internal reflection. The
powder coating
square-base prism is 24% the size of those used in a high-performance fluorescent
Exterior - matte white powder coating.
lens. The exclusive two-dimensional array of prisms is designed to eliminate the
Custom finish is also available.
glare found at higher viewing angles and as such, enables a glare cut-off at a 45º
viewing angle.
CONTROLS
The acrylic material itself is untinted, relying entirely on catadioptric control for
LumenWerx offers several options for integrating
effective source obscuration. A highly efficient TIR process at the acrylic-air
motion and daylight controls into NOVA luminaires.
interface on the prism surfaces redirects incident light with less than a 0.1% loss
Wireless options incorporate a wireless
per reflection. As a result, these LumenWerx optics attain a high optical efficiency
controller/powerpack into the luminaire, which
greater than 90%, while maintaining visual comfort at normal viewing angles and
receives signals from a wireless sensor (by others)
presenting a pleasing luminous appearance.
installed in the space. The advantages of the
wireless option include greater flexibility of control
SIDE LENS - HIGH EFFICIENCY LAMBERTIAN OPTIC (HLO) - shielding of
options, sensor coverage, and system integration.
diffusing 0.075" thick acrylic with up to 88% transmission and good source
Onboard options incorporate both the sensor and
obscuration.
controller/powerpack. Onboard sensors, while
inherently simpler, have limitations of control and
ELECTRICAL
coverage.
Universal input voltages with multiple control schemes offered. Consult factory for
Onboard
availability.
Onboard Motion Sensor and power pack (OMS)
provide automatic on and automatic off control,
EMERGENCY
using PIR detection. Sensor is designed to detect
Factory installed long life high temperature recyclable Ni-Cad battery pack with test
fine-motion when installed within 6' of occupants.
switch and charge indicator, minimum of 90 minutes operation. Recharge time of
Onboard Daylight Sensor and controller (ODS)
24 hours.
provide input for 0-10V dimming drivers. Separate
switched control of line input is required for on/off
MOUNTING OPTIONS
control.
A separate kit for mounting fixtures directly to the ceiling surface. Kit is compatible
with T-Bar, hard surface and drywall ceilings.
49 11/32"
Surface kit
32"
Ceiling holes
25 11/32"
Surface
kit
16"
Ceiling
holes
1 1/2"
Location of an Onboard sensor
Wireless
EnOcean Wireless Controller (EWC) provides both
Power
a power pack for presence detection control and
a 0-10V interface for daylight harvesting. EnOcean
wireless sensors (by others) mounted in the room
signal the onboard EWC. This option permits manual
on/automatic off (vacancy) control.
Lutron Motion Controller (LMC) and Lutron
Daylight Controller (LDC) provide inputs to
SUR - surface mount kit
Ecosystem drivers. Compatible Lutron wireless
motion and daylight sensors (by others) mounted
in the room signal onboard LPC or LDC. This option
permits manual on/automatic off (vacancy) control.
File Name: NOVA24-FLU-SURFACE-SPEC
Page: 4 / 5
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
LumenWerx ULC. reserves the right to change or modify product specifications without notification
July 6, 2016
NOVA24
SURFACE
W W W . L U M E N W E R X . C O M
CONSTRUCTION
Housing - Die formed cold rolled sheet steel 20 gauge thick, matte white powder
coating.
Reflectors - Cold rolled steel 0.030" thick precisely die formed, 95% reflective
matte white painted.
Interior brackets - Die formed cold rolled sheet steel 20 gauge thick.
Center basket - Extruded Aluminum 0.07" nominal, matte white and lens made in
clear PMMA precisely formed into optical micro-structures forms.
Side lenses - Frost impact acrylic lens 88% transmissive.
Surface kit - Extruded Aluminum 0.07" nominal, matte white or silver powder
coating. Custom finishes are also available.
WEIGHT
36.23lbs.+8.26lbs. - 16.45kg+3.75 kg
CERTIFICATIONS
ETL - Rated for Dry/Damp locations. Conforms to UL Standard 1598 and certified to
CAN/CSA Standard C22.2 No. 250.0.
File Name: NOVA24-FLU-SURFACE-SPEC
Page: 5 / 5
www.lumenwerx.com (T) 514-225-4304 (F) 514-931-4862 © All rights are reserved to LumenWerx ULC.
LumenWerx ULC. reserves the right to change or modify product specifications without notification
July 6, 2016