1277 Perimeter Parkway
Virginia Beach VA 23454
Phone: 757 499 7223 Fax: 757 301 6060
E-01
Revised Version
SHOP DRAWING TRANSMITTAL
COMPANY: Tymoff + Moss Architects
DATE: 7/22/14
512 Botetourt Street
Norfolk, VA 23510
ATTENTION: Michael Schnekser
Reviewer: Robert Weise, EIT
REFERENCE:
HRT BUS TRANSFER FACILITY
PACE Project: 13165
DOWNTOWN NORFOLK
WE TRANSMIT THE FOLLOWING:
Copies
Date
Received
Description
email
7/14/14
Electrical Materials
Action
A&R
THESE ITEMS ARE TRANSMITTED:
COMMERCIAL:
GOVERNMENT:
(NET) NO EXCEPTIONS TAKEN
(MCN) MAKE CORRECTIONS NOTED
(A&R) AMEND & RESUBMIT
(R) REJECTED - SEE REMARKS
(RA) RECEIPT ACKNOWLEDGED
(A) APPROVED
(AN) APPROVED AS NOTED
(R) REVISE & RESUBMIT
(D) DISAPPROVED
(RA) RECEIPT ACKNOWLEDGED
REVIEW COMMENTS:
1. General:
a. Revised shop drawings should be submitted individually according to the specification section for
which they are required
2. Panelboards
a. Provide verification of the available fault current from DVP to ensure equipment is properly rated
b. Ensure circuit breaker for the FACP is provided with red markings and provisions to be locked in
the on position
c. Coordinate circuit breaker ratings for all mechanical loads with approved shop drawing submittals
3. Surge Protection Devices
a. Include copy of UL certifications and OCPD requirements per 264313 (1.2)(A)(2)
b. Coordinate circuit breaker rating in Panel “LV1”
c. The peak surge current shall be 200kA per 264313 (2.3)(B)
d. Provide additional documentation to demonstrate compliance with 264313 (2.3)(C-E)
4. Safety Switches
a. Coordinate safety switch and fuse ratings for all mechanical loads with approved shop drawing
submittals
b. Fusible switches shall have a neutral kit and Class-R fuse kit per 262816 (2.1)(B)
5. Occupancy Sensors:
a. Include additional information for ceiling mounted occupancy sensors
b. Coordinate wall plate finish selection with Architect
Color to be White
6. Lighting Fixtures:
a. General:
i. Luminaire quantities not reviewed
Color to be Aluminum
b. Type-EBU
i. Coordinate housing color with Architect
ii. Coordinate trim finish for remote power supply with Architect
iii. Fixtures shall be mullion mounted
Remote power supply to
c. Type-A2 & A2-em
be located in adjacent
i. Coordinate shielding selection with Architect
ceiling. Color to be White
ii. Provide performance reflector
iii. Provide flange kit as required
Shielding type to be Rail
iv. Provide programmed start ballasts per 265100 (2.3)(B)
d. Type-A4 & A4-em
i. Coordinate shielding selection with Architect
Shielding type to be Rail
ii. Provide performance reflector
iii. Provide programmed start ballasts per 265100 (2.3)(B)
e. Type-C & C-em
i. Provide prismatic lens
f. Type-D
i. Provide high impact pearlescent acrylic lens
ii. Provide programmed start ballasts per 265100 (2.3)(B)
g. Type-E & E-em
Provide physical finish
i. Provide programmed start ballasts per 265100 (2.3)(B)
samples for coordination
h. Type-S1
i. Coordinate finish selection with Architect
i. Type-S1 (VE)
i. The Erco "Light Scoop" fixture was used as a basis of design and used for site plan approval from
the City of Norfolk. Provide calculations for approval by the Engineer to ensure lighting levels
and uniformity ratios are equivalent to those submitted to the City.
ii. Confirm NEMA distribution type is equivalent to the basis of design fixture
iii. Coordinate finish selection with Architect
Provide physical finish
j. Type-S2
samples for coordination
i. Coordinate finish selection with Architect
k. Type-S2 (VE)
i. The Hess "Canto G" fixture was used as a basis of design and used for site plan approval from the
City of Norfolk. Provide calculations for approval by the Engineer to ensure lighting levels and
uniformity ratios are equivalent to those submitted to the City.
ii. Confirm lumen output and NEMA distribution type is equivalent to the basis of design fixture
iii. Coordinate finish selection with Architect
l. VE Poles for Type-S2, S3, and S4
i. Ensure poles are rated to withstand winds of 110mph
Provide physical finish
ii. Coordinate finish selection with Architect
samples for coordination
m. Type-S3
i. Coordinate finish selection with Architect
n. Type-S4
i. Coordinate finish selection with Architect
o. Type-S5
i. Coordinate finish selection with Architect
p. Type-S5 (VE)
i. The Forms and Surfaces "Lightscale Bollard" fixture was used as a basis of design and used for
site plan approval from the City of Norfolk. Provide calculations for approval by the Engineer to
ensure lighting levels and uniformity ratios are equivalent to those submitted to the City.
FILE: SHOP DRAWINGS
ii. VE fixture does not appear to provide an equivalent lumen output as the basis of design fixture
iii. Coordinate finish selection with Architect
SHOP DRAWING REVIEW
Review is for general compliance with contract
documents. No responsibility is assumed for
correctness of dimensions or details.
NO EXCEPTIONS TAKEN
MAKE CORRECTIONS NOTED
AMEND & RESUBMIT
X
REJECTED SEE REMARKS
RECEIPT ACKNOWLEDGED
PACE Collaborative, P.C.
Date:
8/7/14
BY (P/M):
Date:
8/7/14
BY (E):
RTW/mlm
FILE: SHOP DRAWINGS
NA
RTW
The owner's current direction is to provide the
"as specified" lighting package. Comments for
the VE options have been included in the event
that the direction changes.
Lighting Virginia East
Lighting Submittals
596 Central Drive Suite 110
Project # 14040
HRT Bus Transfer Station
Virginia Beach, VA 23454
Norfolk, VA
757 463 1100 T
www.LightingVirginia.com
800 316 6113 T
www.FirstLightVA.com
Date:
To:
From:
First Light
757 463 0010 F
Type
Qty Manufacturer
May 16, 2014 11:20
Mayer - Del Slaughter
Mike Bivens
Catalog Number
Volts
.os clg
5
HBA
OMNIDT2000
.os clg pp
5
HBA
UVPP
120/277
.os wall
4
HBA
LHMTS1 (A,B,G,I,W) (please select a standard finish)
120/277
.ebu
9
SignTex
MUE BB 10 X X (please select color and mounting)
.ebu
9
SignTex
RPS BB ML X (please select color)
120/277
.exit1
6
Exitronix
S902-WB-SR-RC-BA
120/277
Exitronix
S903-WB-SR-RM-BA
120/277
.exit2
-
24
12/24V
.control panel
1
HBA
CX082S083LM
120/277
.light sensor
1
HBA
LUXSTATLSO
24
A2
2
Columbia
SER22-217G-(X)(X)-EU (X=please select shielding & reflector)
120/277
A2 em
3
Columbia
SER22-217G-(X)(X)-EU-EL141ST (X=please select shielding & reflector)
120/277
A4
5
Columbia
SER24-232G-(X)(X)-EU (X=please select shielding & reflector)
120/277
A4 em
1
Columbia
SER24-232G-(X)(X)-EU-EL141ST (X=please select shielding & reflector)
120/277
B
18
Prescolite
MD8LED 3L 35K 8 8MD 3L MD25 SL B24
120/277
C
12
Vantage
8HF132E1/2 / 8611SCL
120/277
C em
4
Vantage
8HF132E1/2EM / 8611SCL
120/277
D
4
Kenall
RHL7 24 MW PP 217 IS 1 DV
120/277
E
7
Columbia
KL4 232 U EU S18
120/277
E em
4
Columbia
KL4 232 U EU S18 EL141ST
120/277
G LF
27
iLight
T24 W35 S CL27' NC 00
S1
54
Erco
33237.023 (please confirm finish)
120/277
S1 ve
54 Spaulding
ARF2-K-20L-4K-070-W-U-PS (please confirm finish)
120/277
S2
18
CC450 2LV NW ME UNV A 17RC X oDEG (X = please select finish)
120/277
HessAmerica
120/24
Lighting Virginia East
Lighting Submittals
596 Central Drive Suite 110
Project # 14040
HRT Bus Transfer Station
Virginia Beach, VA 23454
Norfolk, VA
757 463 1100 T
www.LightingVirginia.com
800 316 6113 T
www.FirstLightVA.com
Date:
To:
From:
First Light
757 463 0010 F
Type
Qty Manufacturer
May 16, 2014 11:20
Mayer - Del Slaughter
Mike Bivens
Catalog Number
S2 ve
18 Spaulding
CL1S A 32L U 4K 5W PS RPA4 (please confirm finish)
S2 ve pole
18 Nafco
RSS16-404C (please confirm finish)
S3
6
Kim
1SA ALT3P35 96L 4K 120-277 X VSF-1SA (please select finish)
S3 pole
6
Nafco
RSS30-505D (with 2-3/8" X 4" tenon) (please select finish)
S4
2
Kim
2SB ALT3P35 96L 4K 120-277 X VSF-2SB (please select finish)
S4 pole
1
Nafco
RSS30-505D (with 2-3/8" X 4" tenon) (please select finish)
Volts
120/277
120/277
120/277
S5
22
Forms & Surfaces LBLSC-CF (please advise finish selection)
120/277
S5 ve
22
Trace-Lite
120/277
TLED B 24 DT X (please advise finish selection)
TYPE .os clg pp - 120/277-24V
Power Packs and Relays
Universal Voltage Power Pack
KEY FEATURES
• Universal voltage (100–277 VAC; 50/60Hz)
• Automatic voltage detection
• Electrical load switching capablity: maximum of 20 Amps
• Regulated 24 VDC current; 150mA output; short circuit protected
• Zero Arc Point Switching
• Plenum rated
• Mounts: inside or outside a junction box; inside a fluorescent
ballast cavity
• Available with exclusive Quick to Install (QTI) connector
• UL and cUL listed
• 5-year warranty
UVPP
OVERVIEW
The Universal Voltage Power Pack is a self-contained transformer and relay (an ON/OFF switch controlled by a circuit) designed
for low-voltage 24 VDC occupancy sensors. The power pack supports and automatically detects the line-voltage input within the
100–277 VAC range. This eliminates the need for voltage-specific power packs. This power pack is capable of switching 20A loads
and features Zero Arc Point Switching, minimizing relay-contact wear from high inrush loads. A single power pack can power either 4 sensors or 3 sensors and the MPSA auxiliary relay for multiple circuits. The Universal Voltage Power Pack is plenum rated
and easily mounts either inside or outside a junction box or inside a fluorescent ballast cavity.
FEATURES and BENEFITS
Features
Universal voltage (100–277VAC; 50/60Hz)
Automatic voltage detection
Zero Arc Point Switching
Plenum rated
Optional Quick To Install (QTI) connector
Benefits
• Eliminates the need for specific power packs
• No “specialized wiring” required. It wires the same for all
applications and automatically detects the line voltage being
used
• Minimizes relay-contact wear from high inrush loads
• Complies with requirements for use in a plenum area
• Dramatically reduces installation costs by removing the timeconsuming process of manually wiring a sensor to a power
pack
• Easy to install; fast and efficient; no cutting, stripping,
or wire nuts required
Hubbell Building Automation, Inc. | 9601 Dessau Road | Building One | Austin, Texas 78754 | {512} 450-1100 | {512} 450-1215 fax
hubbell-automation.com
1.2009
TYPE .os clg pp - 120/277-24V
SPECIFICATIONS
Power requirements
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Output
Relay contact rating
Construction
Plenum rated
Operating environment
Size
Color
Certifications
Warranty
How To Order
Catalog Number
UVPP
100–277 VAC; 50/60Hz
Single phase only
24 VDC; 150mA nominal, isolated, and regulated
20A: 120 VAC Incandescent
20A: 120 or 277 VAC Ballast
1HP: 120 or 277 VAC Motor Load
High-impact UL 94-5V plastic
Complies with requirements for use in a plenum area
Plenum rated for external junction box mounting
Indoor use only
Operating temperature: 32o–104o F (0o–40o C)
Relative humidity (non-condensing): 0%–95%
3.69” x 2.33” x 1.36”
Black
UL and cUL listed
5 years
Description
Universal Voltage Power Pack, 100-277VAC, 50/60Hz
* Add QTI to end of catalog number for optional Quick To Install connector.
WIRING DIAGRAM
UVPP Power Pack
Hubbell Building Automation, Inc.
9601 Dessau Road | Building One | Austin, Texas 78754
{512} 450-1100 | {512} 450-1215 fax
hubbell-automation.com
(please select color)
TYPE .os wall - 120/277V
Wall Switch Occupancy Sensors
LightHawk™ Multi-Technology
Wall Switch Sensor featuring IntelliDAPT®
KEY FEATURES
• All-digital dual technology
(ultrasonic [US] and passive infrared [PIR]) sensor
• IntelliDAPT self-adaptive technology—no manual
adjustment required
• Auto-on and manual-on operating modes
(depending on model)
• 1,000 square-foot, 180° coverage area
• Built-in photocell with SuperSaver™ mode
• RhinoTuff™ lens
• Dual 120/277 VAC operation
• No minimum load requirement
• Zero Arc Point Switching
• ETL, UL, and cUL listed
• Five-year warranty
LHMTS1
LHMTS0
OVERVIEW
LHMTS sensors combine ultrasonic (US) and passive infrared (PIR) technologies for unequaled occupancy detection and false
trip immunity. These sensors feature Hubbell Building Automation’s patented IntelliDAPT technology, which makes all the
sensor adjustment decisions automatically. Throughout the product’s lifespan, smart software analyzes the controlled area and
makes digital adjustments to sensitivity and timer settings. Occupancy sensors with IntelliDAPT provide a maintenance-free
install-and-forget operation. With selectable operating modes—automatic ON/OFF or manual ON/automatic OFF—and a builtin photosensor for automatic daylight harvesting, LHMTS sensors are the most capable choice in today’s market place.
FEATURES and BENEFITS
Features
IntelliDAPT technology
All-digital dual technology
(ultrasonic [US] and passive infrared [PIR]) sensor)
Auto-on and manual-on operating modes
(depending on model)
Tamper-proof automatic-only version available
RhinoTuff lens
Built-in photocell with optional SuperSaver mode
Benefits
• Sensor automatically determines the ideal setting for an area
• No manual sensitivity or timer adjustments required
• Provides a maintenance-free install-and-forget operation
• Superior US minor-motion detection with excellent PIR longrange major-motion detection
• Provides auto-on/auto-off and manual-on/auto-off operations
• Automatically turns lighting on and off without requiring the
user to push a button
• Impact-resistant infrared (IR) lens
• Increases energy savings by preventing lights from turning on
when there is sufficient natural light
• Optional SuperSaver mode—turns lights off during periods
of occupancy if there is enough natural light to illuminate the
area
Hubbell Building Automation, Inc. | 9601 Dessau Road | Building One | Austin, Texas 78754 | {512} 450-1100 | {512} 450-1215 fax
hubbell-automation.com
9.2011
(please select color)
SPECIFICATIONS
IntelliDAPT technology
Timer timeout
Ultrasonic (US) output
Passive infrared (PIR)
Photocell
Coverage
Power requirements
Electrical ratings
Load requirements
Operating environment
Construction
Size and weight
Color
Mounting
Certifications
Warranty
TYPE .os wall - 120/277V
• Self-adjusting timer
• Self-adjusting ultrasonic (US) and passive infrared (PIR)
sensitivity
• Automatic false-on/false-off corrections
• No manual adjustments required
• Auto mode: 4–30 minutes; self-adjusts based on occupancy
• Fixed mode: 4, 8, 15, and 30 minutes
• Test mode: 5 seconds
• 40kHz output
• Dual-element pyrometer and 12-element cylindrical RhinoTuff
lens
• Natural light override range: 10–500 foot-candles
• 1,000 square-foot, 180° coverage area
• 120/277 VAC; 50/60Hz
• 120 VAC: 800W Incandescent; 1,000W Fluorescent; 1/6 HP
• 277 VAC: 1,800W Fluorescent; 1/6 HP
• None
• Indoor use only
• Operating temperature: 32°–104°F (0°–40°C)
• Relative humidity (non-condensing): 0–95%
• Casing—high-impact injection-molded plastic (UL-94-5V)
• Impact-resistant lens
• Color-coded leads are 6” long
• Size: 4.2” x 1.8” x 2.1”; .37” extension
• Weight: 2.9 oz
• White; Ivory; Light Almond; Gray; Black
• Single-gang NEMA-style switch box (average switch box)
• Decorator-style wall plate not included
• ETL, UL, and cUL listed
• Five years
ORDERING INFORMATION
Catalog Number Description
LHMTS1*
Ultrasonic and PIR Wall Switch Sensor with IntelliDAPT and Automatic/Manual Control, 120/277VAC
LHMTS0*
Ultrasonic and PIR Wall Switch Sensor with IntelliDAPT and Automatic Only Control, 120/277VAC
* = W – White, I – Ivory, A – Light Almond, G – Gray, B – Black
WIRING DIAGRAM
RANGE DIAGRAM
*Refer to Application Guide.
Hubbell Building Automation, Inc.
9601 Dessau Road | Building One | Austin, Texas 78754
{512} 450-1100 | {512} 450-1215 fax
hubbell-automation.com
TYPE .ebu - 12/24V
(please select color & mounting)
Moonlite LED™
Mullion Mount Emergency Light
Outdoor Egress
Series MUE
MUE.02.13.09
The Brightest
Idea
is Emergency Lighting with LEDs
GENERAL DESCRIPTION
Operating in either normal-on or emergency mode,
this fixture is designed to mount directly on structural
mullion beams used in typical glass-fronted entrances,
with vertical surface as small as 2”. This fixture has full
90° cut-off and will provide efficient emergency lighting
in front of egress doorways, or along extended
pathways.
series MUE
CONSTRUCTION
• Rugged extruded aluminum housing with stainless
hardware is corrosion proof.
• Wet location listed UL 924. Certified IP66.
• Uniform, high brightness lighting over the path of
egress.
• Full 90° cut- off.
ENERGY EFFICIENT OPERATION
• Dual function operation for normally on night or
security lighting as well as emergency lighting.
• Very low power consumption in night/ security
mode. The security lighting circuit is independent
of emergency lighting and may be switched
manually, by an exterior photocell, or other
automatic means.
• Three versions are available:
• Over 50,000 hour lamp life in normal use.
RE= Central Battery System Series CBS or other
qualified source 12V- 24 VDC.
BB= Battery backup from Remote Battery Supply
Series RPS.
AC= 120VAC supply: 277 VAC option.
• IES photometric data available for all models.
CODES
ELECTRONICS
• Manufactured and tested to UL Standard 924 and
NFPA Life Safety Code 101.
• Dual operation from either a battery or normally on
power source.
WARRANTY
• Lamps are connected in parallel-series strings, as
required to meet requirements of NEC and Life
Safety Codes. Lighting continues even after failure of
One lamp or circuit.
• 5 year total customer satisfaction warranty. For
Details see product catalog technical data section.
D E S I G N E D
& M A D E I N
E
INT
RTEK
CM
US
LISTED
FIXTURE SCHEDULE
MODEL
CATALOG NO
APPROVAL
JOB INFORMATION
T H E
U S A
2003529
Signtex Inc
LIGHTING
SPECIFIED EMERGENCY LIGHTING
TYPE .ebu - 12/24V
(please select color & mounting)
Moonlite LED™
Mullion Mount Emergency Light
Outdoor Egress
Series MUE
MUE.02.13.09
SPACING GUIDE
SUGGESTED SPECIFICATIONS:
Supply and install the MOONLITE LED Series MUE Mullion Mount emergency lighting
fixture manufactured by Signtex Lighting Inc. The MUE assembly shall be listed for
installation in wet locations in compliance with UL 924 and IP66 standards and shall be
capable of operating from Signtex remote power supply Series RPS, the Signtex central
battery system Series CBS, or from other remote power sources supplying 12-24 VDC or
VAC. Upon loss of AC building power, emergency models shall operate for a minimum of
90 minutes in compliance with UL Standard 924 and NFPA LSC 101.
2 5'
12'
MOUNTING DATA & DIMENSIONS:
MULLION MOUNT
L
Average Illuminance 1 Fc
Model Shown: MUE 10 Watts
NOTE: FOR REFERENCE ONLY. STANDARD REFLECTANCES
80/50/20. SIGNTEX IS NOT RESPONSIBLE FOR SPECIFIC
CONDITIONS THAT MAYALTER THE RESULTS.
5"
CONTACT SIGNTEX FOR LAYOUT ASSISTANCE
1 1/2"
2 1/2"
Code Compliant Emergency lighting layouts provided free of charge!
BATTERY & AC ONLY MODELS
2 1/4"
TOP MOUNT
2 3/4" MOUNT
SCREW LOCATIONS
INPUT
120/277 VAC
GLASS
PANEL
MUE
MULLION
RPS
See RPS
Data Sheet
OUTPUT 4.8V - 24V
MAX WIRING LENGTH
FROM RPS TO FIXTURE
LENGTH (FT)
WIRING
SIZE AWG
BB & AC
BB and AC Models: 4 Conductors
RE Models: 3 Conductors
Emergency Power Rating (EPR): 10 WATTS
Security Power Rating (SPR): 10 WATTS
#20
100
#18
170
RPS SELF- TEST DIAGNOSTIC FUNCTIONS
#16
225
BB MODELS WITH DG FUNCTION
STATUS
LENGTH TABLE
L
POWER
10 Watts
10"
20 Watts*
LED DISPLAY
NORMAL FULL CHARGE
NORMAL FAST CHARGE
FAILED BATTERY
FAILED LAMP
FAILED TRANSFER
FAILED CHARGER
21"
WIRING
Typical Specification:
UL AWM Style: Control Cable #20 AWG 300V 2 conductors.
GREEN ON
ORANGE ON
RED FLASH FAST
GREEN FLASH
ORANGE FLASH
RED FLASH SLOW
*RE and AC models only
SECURITY / NIGHT LIGHTING
BB Models with SW Option
RE Models (All)
EM Watts SEC Power- Watts
10
20
10
20
SW OPTION CONTROL WIRING
Standard BB =
Connect ORANGE & GREEN wires
together to turn ON
BB with DG Option= Connect BLUE wire to voltage source
from 10V to 300V AC or DC to turn ON
FIXTURE ORDERING INFORMATION: EXAMPLE: MUEBB10AW-DG
MUE
BB
BB
MODEL SERIES
OPERATION
RE= Central Battery or
other 12- 24 VDC
Remote Source
BB= Battery Backup
(Requires RPS)
AC= No Battery
(Requires RPS)
MUE
10
10
X
A
X
W
-DG
EMERGENCY
POWER RATING
HOUSING COLOR
MOUNT
OPTIONS
10= 10 Watts
20= 20 Watts*
*RE and AC
models only.
See Length
Table.
W= Satin White
A= Aluminum
X= Custom
T= Top
W= Wall
DG= Battery Diagnostics*
SW= Security Lighting with
Control Switch*
2HT= 2" Canopy Height
Signtex
Inc
LIGHTING
SUITABLE FOR WET LOCATIONS
*BB Models Only
AMBIENT TEMPERATURE LIMITS:
Standard "BB" models: -20º C to +40º C
Remote models: -40º C to +50º C
DISTRIBUTOR:
220 VFWAvenue, Grasonville,MD21638
TEL:(410)827-8300 Fax:(410)827- 8866
Specifications and Dimensions subject to change without notice.
sales@signtexinc.com www.signtexinc.com
TYPE .ebu - 120/277V
(please select color)
Remote Power Supply
For Moonlite Emergency Fixtures & Exit Signs
Series RPS
RPS.06.12.05
GENERAL DESCRIPTION
The Remote Power Supply is capable of powering
any MOONLITE LED or LED Exit sign manufactured
by Signtex Lighting, Inc. The RPS can be mounted
in any accessible wall or ceiling. A removable cover
allows easy access to the electronics for service.
Available with battery backup or AC supply only.
INPUT
120/277
VAC
REMOTE
EXIT
RPS
ELECTRONICS
• Isolated, all solid state power supply with
2- wire universal input from 120 VAC to 277 VAC
with precise current and voltage regulation.
• Power supply is surge and spike protected, with a
low voltage disconnect.
• The complete power supply module with optional
NICAD battery pack is sealed within a phenolic
plastic enclosure. AC and DC wiring is quickly
attached with plug connectors.
BB Models: 3 Conductors
AC Models: 2 Conductors
INPUT
120/277
VAC
MOONLITE LED
RPS
DIAGNOSTICS OPTION
• An advanced microprocessor monitors
all charger functions and battery condition
continuously and automatically performs all
tests and visual indications required by
UL Standard 924.
BB and AC Models: 2 Conductors
CODES
• Manufactured and tested to UL Standard 924.
Conforms to NFPA Life Safety Code 101, UBC
and NEC.
WARRANTY
• 5 year total customer satisfaction warranty. For
details see product catalog technical data section.
D E S I G N E D
&
M A N U F A C T U R E D
ERTEK
INT
CM
US
LISTED
I N
FIXTURE SCHEDULE
MODEL
APPROVAL
T H E
U S A
2003529
CATALOG NO
JOB INFORMATION
Signtex Inc
LIGHTING
SPECIFIED EMERGENCY LIGHTING
TYPE .ebu - 120/277V
(please select color)
Remote Power Supply
For Moonlite Emergency Fixtures & Exit Signs
Series RPS
RPS.06.12.05
SUGGESTED SPECIFICATIONS:
Supply and install the Remote Power Supply Series RPS manufactured by Signtex Lighting Inc. The RPS will be capable of
operating any exit sign or MOONLITE LED emergency fixture manufactured by Signtex Lighting Inc. and shall be available
with a NICAD battery and charger with universal 120/277 VAC input, to supply emergency lighting operation for a minimum
of 90 minutes in compliance with UL Standard 924 and NFPA LSC 101, or as a power supply without battery. The RPS shall
also be capable of operating MOONLITE LED fixtures manufactured by Signtex in normally- on or continuous mode, from
120/277VAC power input.
MOUNTING DATA & DIMENSIONS:
INPUT
120/ 277 VAC
MAX WIRING LENGTH
FROM RPS TO FIXTURE
LENGTH (FT)
WIRING
SIZE AWG
BB & AC
8 1/2”
STATUS INDICATOR
PUSH TO TEST
#20
100
#18
170
#16
225
5”
3 3/4”
0UTPUT
5 V - 24 V
7 3/8”
BACK BOX
ACCESS
COVER
SELF- TEST DIAGNOSTIC FUNCTIONS
STATUS
3 1/2"
STANDARD MASONRY BOX 3 3/4" X 3 1/2" X 7 3/8"
(SUPPLIED BY OTHERS)
TYPICAL STOCK MODELS:
CROUSE HINDS #TP693
RACO # 698
ORDERING INFORMATION: EXAMPLE: RPSBBMLW-DG
RPS
ML
BB
LED DISPLAY
NORMAL FULL CHARGE
NORMAL FAST CHARGE
FAILED BATTERY
FAILED LAMP
FAILED TRANSFER
FAILED CHARGER
X
W
GREEN ON
ORANGE ON
RED FLASH FAST
GREEN FLASH
ORANGE FLASH
RED FLASH SLOW
-DG
MODEL SERIES
OPERATION
FIXTURE
TRIM FINISH
OPTIONS
RPS=REMOTE
POWER
SUPPLY
BB= Battery Backup
NB=No Battery
ML= Moonlite LED
EX= Exit LED
W= White
A= Aluminum
X= Custom
DP = Damp Location
DG = Battery Diagnostics
DAC= Dual AC Input
(120 VAC)
SW = Security Lighting
Control Switch
HS = High Power Security
Lighting
Signtex
Inc
LIGHTING
DISTRIBUTOR:
220 VFWAvenue, Grasonville,MD21638
TEL:(410)827-8300 Fax:(410)827- 8866
Specifications and Dimensions subject to change without notice.
sales@signtexinc.com www.signtexinc.com
TYPE .exit1 - 120/277V
S900 Series
universal swivel mount led edge-lit exit sign
Model Number:
Accessories:
Job:Type:
Approvals:
Features
•Pivoting design for simple installation in any application, including
wall, ceiling, sloped ceiling or recessed mounting in single or double
face configurations
•Truly universal (“SR”) model includes surface mounting canopy as
well as back box for recessed mounting applications
•Die-cast aluminum housing with high-grade, optically true, acrylic
panel
•Compact, low profile design
Wall
•Low energy consumption
Ceiling
•Mirror panel supplied as a standard on all double-faced signs
•ETL listed 90 minute emergency run time, 24 hour recharge time
•Low voltage disconnect eliminates deep discharge
•Optional Guardian Self-Test/Self-Diagnostics (G2) available
•Constant, uniform illumination by long-life, high intensity, red or
green LEDs
•Fully-illuminated 6” characters with 3/4” stroke
End
•Field applicable chevrons provided
Sloped Ceiling
•120/277V dual primary, 60Hz input
•Standard finishes: White or brushed aluminum
•Suitable for damp location
Recessed
Warranty
Any component that fails due to manufacturers defect is guaranteed
for 5 years with a separate 3 year pro-rated warranty on the battery.
The warranty does not cover physical damage, abuse or acts of God.
Manufacturer reserves the right to charge for such repairs if deemed
necessary.
SPECIFICATIONS ARE SUBJECT
TO CHANGE WITHOUT NOTICE
ORDERING INFORMATIONExample: S902-WB-SR-RM-BA-G2
Series
Power Source
Mounting
Panel Color
Finish
Options (Factory Installed)
S902 = Single Face
LB = AC Only
S = Surface
Single Face
WH = White
G2 = Self-Test/Self-Diagnostics
S903 = Double Face
WB = With Battery
SR1 = Universal
RC = Red Letters/Clear Panel
BA = Brushed Alum.
GC = Green Letters/Clear Panel
Double Face
RM = Red Letters/Mirror Panel
GM = Green Letters/Mirror Panel
1
SR option includes kits for surface & recessed mounting
10800157 02/13
TYPE .exit1 - 120/277V
CONSTRUCTION
Housing
Available in either a powder coated or brushed aluminum finish.
INSTALLATION
Surface Mounting: Completely universal canopy provides for side,
ceiling or flush mounting. All hardware is included.
Surface Mounting
Engineering grade aluminum extrusion with mounting canopy
Recessed Mounting: Recessed ceiling mount, accessible above the
plenum. Electronics and battery contained in housing. Plug-in battery
connector supplied for easy installation. All hardware is included.
Recessed Mounting
Extruded aluminum housing supplied with galvanized steel adjustable
bar hanger assembly. Panels
Constructed of high quality, optically true, clear acrylic with beveled
lettering for maximum light output. Exit letters are 6" high with a 3/4"
stroke. Double face panels are supplied with a mirror insert. Units
are supplied with press-on directional arrows for placement in all
applications.
Stencil letters are 6” high with 3/4” stroke, with minimum of 100 ft
viewing distance rating as required by UL924 standard.
ILLUMINATION
High output red or green LEDs provide superior brightness. Energy
consumption of less than 3 watts for AC only or less than 5 watts for
battery back-up units. LEDs are a maintenance-free solution, providing
up to 100,000 hours of use without failure.
ELECTRICAL
Input
Dual-voltage input 120 or 277VAC @ 60Hz
OPTIONS
Guardian Self-Test/Self-Diagnostics (Option: G2)
The Guardian circuit continuously monitors the operating condition of
the AC power, battery supply voltage, emergency lamp continuity and
charging circuit.
The purpose of this option is to provide visual signaling in response
to a fault at the EXIT sign battery and/or battery charger. If a failure is
detected, visual status will occur immediately via the CHARGER LED
and/or the BATTERY FAULT LED. The LEDs will stay illuminated until
the fault is corrected.
The Guardian circuit also monitors the transfer circuit as well as
performing automatic code compliant testing. The Guardian circuit will
perform a 30 second discharge and self-test every 28-30 days. A 90
minute discharge and self-test is performed every 6 months.
CONFORMANCE TO CODES & STANDARDS
The S900 Series is ETL listed and meets or exceeds the following: UL
924, NEC requirements and NFPA 101.
DIMENSIONS
Sealed Nickel Cadmium Battery - NiCad (With Battery Only)
Exitronix sealed nickel cadmium batteries are maintenance-free with
a life expectancy of 15 years. Nickel cadmium batteries offer high
discharge rates and continue to perform in a vast temperature range
from 0-40 degrees C. NiCad technology provides long lasting, safe and
reliable performance by utilizing the jelly-roll design and allows a Ni-Cad
cell to deliver a much higher maximum current than an equivalent size
alternative battery. As a relatively larger area of the electrode is in
contact with the active material in each cell, the internal resistance for
an equivalent sized NiCad cell is lower which increases the maximum
current that can be delivered.
Brownout Circuit
The brownout circuit monitors the flow of AC current to the unit and
triggers the emergency lighting system once a set reduction of AC
power occurs. This dip in the voltage will cause many fixtures to
extinguish causing loss of normal lighting even though a total power
failure has not occurred.
Low Voltage Disconnect
When the battery’s terminal voltage falls below predetermined levels,
the low-voltage circuit disconnects the emergency lighting load. The
disconnect remains in effect until normal power is restored, preventing
deep battery discharge and improving the life of the battery. The
disconnect will also automatically reconnect the load circuit once the
battery voltage returns to a normal value after charging.
3.5”
13”
1.63”
9.63”
8.68”
3.13”
14.96”
2.81”
4”
Solid-State Transfer
The unit features a solid-state switching transistor which eliminates
damaged contacts or mechanical failures associated with relays.
The switching circuit is designed to detect a loss of AC power and
automatically energizes the lamps. Upon restoration of the AC voltage,
the emergency lamps will switch off and the charger will automatically
recharge the battery.
Overload and Short-Circuit Protection
The solid-state overload monitoring system in the DC circuit disconnects
the lamp load from the battery should excessive wattage demands be
made and automatically resets when the overload or short-circuit is
removed. This overload current protective characteristic eliminates the
need for fuses or circuit breakers for the DC load.
Test Button
Our easily located test button allows for manual verification of proper
operation of the transfer circuit and emergency lamps.
1911 W. Parkside Lane • Phoenix, AZ 85027
(800) 533-3948 • Fax: (623) 580-8948
www.exitronix.com • www.barronltg.com
7.5”
12.69”
TYPE .exit2 - 120/277V
S900 Series
universal swivel mount led edge-lit exit sign
Model Number:
Accessories:
Job:Type:
Approvals:
Features
•Pivoting design for simple installation in any application, including
wall, ceiling, sloped ceiling or recessed mounting in single or double
face configurations
•Truly universal (“SR”) model includes surface mounting canopy as
well as back box for recessed mounting applications
•Die-cast aluminum housing with high-grade, optically true, acrylic
panel
•Compact, low profile design
Wall
•Low energy consumption
Ceiling
•Mirror panel supplied as a standard on all double-faced signs
•ETL listed 90 minute emergency run time, 24 hour recharge time
•Low voltage disconnect eliminates deep discharge
•Optional Guardian Self-Test/Self-Diagnostics (G2) available
•Constant, uniform illumination by long-life, high intensity, red or
green LEDs
•Fully-illuminated 6” characters with 3/4” stroke
End
•Field applicable chevrons provided
Sloped Ceiling
•120/277V dual primary, 60Hz input
•Standard finishes: White or brushed aluminum
•Suitable for damp location
Recessed
Warranty
Any component that fails due to manufacturers defect is guaranteed
for 5 years with a separate 3 year pro-rated warranty on the battery.
The warranty does not cover physical damage, abuse or acts of God.
Manufacturer reserves the right to charge for such repairs if deemed
necessary.
SPECIFICATIONS ARE SUBJECT
TO CHANGE WITHOUT NOTICE
ORDERING INFORMATIONExample: S902-WB-SR-RM-BA-G2
Series
Power Source
Mounting
Panel Color
Finish
Options (Factory Installed)
S902 = Single Face
LB = AC Only
S = Surface
Single Face
WH = White
G2 = Self-Test/Self-Diagnostics
S903 = Double Face
WB = With Battery
SR1 = Universal
RC = Red Letters/Clear Panel
BA = Brushed Alum.
GC = Green Letters/Clear Panel
Double Face
RM = Red Letters/Mirror Panel
GM = Green Letters/Mirror Panel
1
SR option includes kits for surface & recessed mounting
10800157 02/13
TYPE .exit2 - 120/277V
CONSTRUCTION
Housing
Available in either a powder coated or brushed aluminum finish.
INSTALLATION
Surface Mounting: Completely universal canopy provides for side,
ceiling or flush mounting. All hardware is included.
Surface Mounting
Engineering grade aluminum extrusion with mounting canopy
Recessed Mounting: Recessed ceiling mount, accessible above the
plenum. Electronics and battery contained in housing. Plug-in battery
connector supplied for easy installation. All hardware is included.
Recessed Mounting
Extruded aluminum housing supplied with galvanized steel adjustable
bar hanger assembly. Panels
Constructed of high quality, optically true, clear acrylic with beveled
lettering for maximum light output. Exit letters are 6" high with a 3/4"
stroke. Double face panels are supplied with a mirror insert. Units
are supplied with press-on directional arrows for placement in all
applications.
Stencil letters are 6” high with 3/4” stroke, with minimum of 100 ft
viewing distance rating as required by UL924 standard.
ILLUMINATION
High output red or green LEDs provide superior brightness. Energy
consumption of less than 3 watts for AC only or less than 5 watts for
battery back-up units. LEDs are a maintenance-free solution, providing
up to 100,000 hours of use without failure.
ELECTRICAL
Input
Dual-voltage input 120 or 277VAC @ 60Hz
OPTIONS
Guardian Self-Test/Self-Diagnostics (Option: G2)
The Guardian circuit continuously monitors the operating condition of
the AC power, battery supply voltage, emergency lamp continuity and
charging circuit.
The purpose of this option is to provide visual signaling in response
to a fault at the EXIT sign battery and/or battery charger. If a failure is
detected, visual status will occur immediately via the CHARGER LED
and/or the BATTERY FAULT LED. The LEDs will stay illuminated until
the fault is corrected.
The Guardian circuit also monitors the transfer circuit as well as
performing automatic code compliant testing. The Guardian circuit will
perform a 30 second discharge and self-test every 28-30 days. A 90
minute discharge and self-test is performed every 6 months.
CONFORMANCE TO CODES & STANDARDS
The S900 Series is ETL listed and meets or exceeds the following: UL
924, NEC requirements and NFPA 101.
DIMENSIONS
Sealed Nickel Cadmium Battery - NiCad (With Battery Only)
Exitronix sealed nickel cadmium batteries are maintenance-free with
a life expectancy of 15 years. Nickel cadmium batteries offer high
discharge rates and continue to perform in a vast temperature range
from 0-40 degrees C. NiCad technology provides long lasting, safe and
reliable performance by utilizing the jelly-roll design and allows a Ni-Cad
cell to deliver a much higher maximum current than an equivalent size
alternative battery. As a relatively larger area of the electrode is in
contact with the active material in each cell, the internal resistance for
an equivalent sized NiCad cell is lower which increases the maximum
current that can be delivered.
Brownout Circuit
The brownout circuit monitors the flow of AC current to the unit and
triggers the emergency lighting system once a set reduction of AC
power occurs. This dip in the voltage will cause many fixtures to
extinguish causing loss of normal lighting even though a total power
failure has not occurred.
Low Voltage Disconnect
When the battery’s terminal voltage falls below predetermined levels,
the low-voltage circuit disconnects the emergency lighting load. The
disconnect remains in effect until normal power is restored, preventing
deep battery discharge and improving the life of the battery. The
disconnect will also automatically reconnect the load circuit once the
battery voltage returns to a normal value after charging.
3.5”
13”
1.63”
9.63”
8.68”
3.13”
14.96”
2.81”
4”
Solid-State Transfer
The unit features a solid-state switching transistor which eliminates
damaged contacts or mechanical failures associated with relays.
The switching circuit is designed to detect a loss of AC power and
automatically energizes the lamps. Upon restoration of the AC voltage,
the emergency lamps will switch off and the charger will automatically
recharge the battery.
Overload and Short-Circuit Protection
The solid-state overload monitoring system in the DC circuit disconnects
the lamp load from the battery should excessive wattage demands be
made and automatically resets when the overload or short-circuit is
removed. This overload current protective characteristic eliminates the
need for fuses or circuit breakers for the DC load.
Test Button
Our easily located test button allows for manual verification of proper
operation of the transfer circuit and emergency lamps.
1911 W. Parkside Lane • Phoenix, AZ 85027
(800) 533-3948 • Fax: (623) 580-8948
www.exitronix.com • www.barronltg.com
7.5”
12.69”
TYPE .control panel - 120/277V
CX Lighting Control Panels - 4 and 8 Relays
TITLE
24
COMPLIANT
CALIFORNIA
CX COMMERCIAL LIGHTING CONTROL PANELS
120
277
VAC
PROJECT INFORMATION
Project Name
Catalog No.Date
The Hubbell Building Automation CX Commercial Lighting Control Panels
provide feature-rich and cost-effective lighting control for maximum energy
savings. The LCD User interface is located in the door and utilized simple and
intuitive scrolling menus to program, check status or update the panel. The
easy-to-use Pre-Programmed Scenarios Menu makes project commissioning
simple and fast.
The CX Panels can save up to 50% in labor and materials when used in place
of conventional time clock and contactor combinations. The use of the
astronomical clock instead of roof-mounted photocells increases cost savings,
lowers maintenance, and improves reliability.
PRODUCT FEATURES
• Two Relay panel sizes – 4 and 8 relay spaces
• Four types of relays – 20A/1P, N/O, 20A/2P, N/O, N/C (14K SSCR) 14.5”
and 30A/1P latching (18K SCCR)
• LCD user interface with keypad
• 365 day programming with 64 schedules
• Astronomical and real time clock
• 12 Programmable dry contact inputs for 8 relay panel;
• 6 programmable dry contact inputs for 4 relay panel
17”
• Selectable pre-programmed scenarios
• Programmable inputs accept low voltage switches, photocells, or motion sensors
•
Two low voltage dry contact output relays on 8 relay panel
• Program uploads via removable SD memory card
• Listed to UL916, UL924 and cUL
• Five -year limited warranty
4”
TYPE .control panel - 120/277V
General Specifications
Programming and configuration Programmable via user interface mounted on door
Fully programmable by users with door closed and locked
Physical NEMA 1 surface enclosure
Pre-drilled mounting holes for mounting to wall, KOs provided on top and bottom
4 and 8 relay enclosures with hinged locking door
Electrical input 120-277VAC Standard, 347/480 Optional
Relays
120 and 277VAC 20 Amp Single Pole Relays (14K SCCR)
120 and 277VAC 30 Amp Single Pole Relays (18K SCCR)
347 VAC, 20A, IP Relay (14K SCCR)
208, 240, and 480VAC 20 Amp Double Pole Relays (14K SCCR)
Operating environment Location: interior space
Operating temperature: 0° to 50°C (32° to 112°F)
Relative humidity (non-condensing): 10% to 90%
Certifications Listed to UL916, UL924 and cUL
Warranty
Five-years limited
Ordering Information
CX
MODEL
CX CX Lighting
Control
Panel
08
SPACES
04 4 Relay
Spaces
08 8 Relay
Spaces
2
S
INPUT VOLTAGE
2 120/277V
ENCLOSURE
S NEMA 1
Universal
Surface
3 347/480V
08
M
RELAY QUANTITY
00 No Relays Spaces Only
04 4 Relays
Installed
08 8 Relays
Installed
NOTES:
1.
2-Pole relays take the same amount of space as 1-Pole relays.
2.
Installed relays must be all of the same type. Relay Type TC not available in fully
populate panels and must be ordered separately to be installed in the field.
3.
“00” option has no relays, all must be installed in the field.
4.
Secondary panel includes (2) master/secondary panel interface cards.
5.
Master/Secondary available in 8 relay only.
9601 Dessau Road | Building One | Austin, Texas 78754 | 512-450-1100 | 512-450-1215 fax | www.hubbell-automation.com
RELAY TYPE
SP Space Only
2N 20A
Electrically
Held N/O
120-277V
3L Latching
120-277-347V
TN 20A
Electrically
Held
N/O 208480V
OPTIONS
N Stand Alone
Panel
M Master Panel
S Secondary
Panel
(Note 4 & 5)
3300A 1.2.2014
TYPE .light sensor - 24V
Luxstat Light Sensor
TITLE
24
LOW
COMPLIANT
CALIFORNIA
DAYLIGHTING CONTROLS
24
PROJECT INFORMATION
Project Name
VDC
VOLTAGE
Catalog No.Date
The Luxstat Light Sensor by Servodan provides the necessary daylight-level
information to the Luxstat daylight harvesting control modules. Using a
photodiode element, this sensor continuously measures daylight levels and
sends the information to the selected Luxstat daylight harvesting control
module. In order to operate as a true Open Loop controller, the sensor
must be positioned to see only daylight (no artificial light). You select the
applicable foot-candle range by using a jumper beneath the front cover.
LUXSTATLS
PRODUCT FEATURES
DAYLIGHT
HARVESTING
• Daylight sensor for Luxstat Daylight Harvesting System
• Architecturally attractive design
• Indoor and outdoor versions
• Open loop operation
• Foot-candle range: 3-6,000 fc
• Mounts vertically or horizontally
• Color coded, plug-and-play installation
• UL and cUL listed
• California Title 24 Compliant
• Five-year limited warranty
1.2”
2”
TYPE .light sensor - 24V
Lux
Light sensor
0-10V
1
2
3
45º
Luxstat Control
A
B
17 23
45
68
91
01
11
2
30º
A
17 23
78-050
45
68
91
01 11 2
B
30º
Luxstat Control DIM
General Specifications
Electrical
Four jumper-selectable foot-candle ranges: .03-30FC; 3-300FC;
30-3,000FC; 60-6,000FC
24VDC Low Votage Class 2 Device
3-conductor 22 AWG twisted cable—equal to Belden 8443
Construction
Protective hard plastic cover and housing
Dimension
2” diameter x 1.2” height (50.8 diameter x 30.5mm height)
Certifications
UL and cUL listed
Warranty
Five years
Ordering Information
LUXSTATLSO
LUXSTATLS
LUXSTATLSO
MODEL
Luxstat Light Sensor - Indoor
Luxstat Light Sensor - Outdoor
9601 Dessau Road | Building One | Austin, Texas 78754 | 512-450-1100 | 512-450-1215 fax | www.hubbell-automation.com
5601A 12.23.2013
TYPE A2 em - 120/277V
(please advise shielding & reflector)
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
PROJECT INFORMATION
FEATURES
•
•
•
•
•
•
•
•
•
•
Architecturally enhanced triple lens design
Full distribution provides controlled high angle light for visual comfort and
more inviting spaces
Advanced optics produce high efficiencies
Hinged optical system allows easy access to lamps and electrical from below
the ceiling
Lenses interlock for structural integrity
Two optional lens aesthetics
Exclusive optional T8 EnergyMax® tuned 1.04 ballast factor ballast
Step and full dimming options for both T5 and T8 expand energy savings
opportunities
Most configurations produce low W/ft2 to meet the most restrictive lighting
power density codes
Available with exclusive wiHUBB technology preinstalled
Made with 90% recycled steel
Made of 80% recyclable materials by weight
Job pack available for minimizing amount of packaging material at job site
Individual cartons made of 100% recycled corrugated
Please go to http://www.hsi/productsustain.com for Hubbell Sustainable
Design Solutions Feature Criteria.
*
ORDERING INFORMATION
SER
22 – 2
17
MODEL
G
CEILING TYPE
G Grid
SM Surface Mount
For hard ceilings use
flange kit.
SIZE
ACCESSORIES
(ORDER
SEPARATELY)
FK22 2' × 2' Single
Flange Kit
FKCR Flange Kit Row
Adaptor
ELECTRICAL
Standard class “P”, thermally protected, autoresetting
HPF ballast, sound rated A. CEE NEMA Premium compliant.
All ballast leads extend a minimum of 6" through access
location. NEC/CEC-compliant ballast disconnect is standard.
FINISH
All visible parts are custom formulated soft, non-glare
high-reflectance white powder coat finish, painted after
fabrication.
EMERGENCY
Field installation of battery packs requires use of remote
test switch.
INSTALLATION
An access plate is furnished with each recessed fixture for
fast wiring connections without the necessity to open the
fixture or wireway.
BALLASTS
Energy efficient, thermally protected, automatic
resetting, Class P, high power factor, sound rated A,
magnetic or electronic ballasts. CEE NEMA Premium
compliant.
X
SHIELDING
C Contour
R Rail
LAMP TYPE
14
17
24
40TT
2', T5: 14 Watt
2', T8: 17 Watt
2', T5HO: 24 Watt
Twin Tube Compact, 2G11
Base: 40 Watt
CEILING COMPATIBILITY
Luminaire is available to fit exposed grid ceilings, or hard
ceilings when a flange kit is ordered. Some options may
increase fixture depth. For information on compatibility
with specific ceilings, or where plenum depth is a problem,
contact your Columbia Lighting representative. Four integral
T-bar clips are standard.
CERTIFICATION
All luminaires are built to UL 1598 standards and bear
appropriate UL and cUL or CSA labels. IC Rating optional for
some configurations. Damp location labeling is standard.
Emergency-equipped fixtures labeled UL 924.
–
X
E
REFLECTOR
P Performance
F Full
–
U
EP95
EP115
ESD115
ETT
EPTT
Electronic T8, 0.88 Ballast Factor, Instant Start
Electronic T8, T5, T5HO Dimming, Programmed Start 1
Electronic T8, 0.88 Ballast Factor, Step Dimming, Programmed Start
Electronic T8, 0.77 Ballast Factor, Low Wattage, Instant Start
Electronic T8, 1.18 Ballast Factor, High Wattage, Instant Start
Electronic T8, 1.04 Ballast Factor, Instant Start (N/A 1-Lamp)
Electronic T8, 1.04 Ballast Factor, Step Dimming, Programmed Start
Electronic T8, 1.04 Ballast Factor, Programmed Start
Electronic T5, T5HO, 1.0 Ballast Factor or T8,
0.88 Ballast Factor, Programmed Start
Electronic T5, 0.95 Ballast Factor , Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 0.95 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO, 1-Lamp)
Electronic T5, 1.15 Ballast Factor, Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 1.15 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO)
Electronic Twin Tube, Instant Start
Electronic Twin Tube, Programmed Start
Page 1/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
–
VOLTAGE
EL141ST
OPTIONS
C388 3-Wire Flex
C488 4-Wire Flex
C588 5-Wire Flex
EL141 Emergency Battery Pack (self test)
GLR Fast Blow Fuse
GMF Slow Blow Fuse
NYC NYC Compliant
WIH wiHUBB Enabled 2
IC IC Rating
U 120V-277V
347 347V2
BALLAST
E
ED
ESD
ELW
EHL
E104
ESD104
EP104
EP
ESD95
Damp Label - standard
1
Where available.
2
Not available with surface mount.
Date
CONSTRUCTION
Luminaire housing, end caps, and reflectors are die-formed
code-gauge cold-rolled steel. Optical system hinges for easy
access to lamps and electrical components. Mechanical light
trap prevents light leaks. Latches are spring loaded.
–
1 One
(N/A 17, 14, 24)
2 Two
3 Three
(N/A TT)
22 2' × 2'
Catalog No.
EXAMPLE SER22-314G-CP-EPU
NO. OF LAMPS
SER Serrano®
Recessed
Architectural
Luminaire
Type
SHIELDING
Lenses are high transmission extruded acrylic.
HUBBELL SUSTAINABLE DESIGN SOLUTION FEATURES*
•
•
•
•
Project Name
LAMPS
FO730
FO735
FO741
FO830
FO835
FO841
F5830
F5835
F5841
FTT830
FTT835
FTT841
30K 75CRI T8 Lamps Installed
35K 75CRI T8 Lamps Installed
41K 75CRI T8 Lamps Installed
30K 82CRI T8 Lamps Installed
35K 82CRI T8 Lamps Installed
41K 82CRI T8 Lamps Installed
30K 85CRI T5 or T5HO Lamps Installed
35K 85CRI T5 or T5HO Lamps Installed
41K 85CRI T5 or T5HO Lamps Installed
30K Twin Tube Lamps Installed
35K Twin Tube Lamps Installed
41K Twin Tube Lamps Installed
RECESSED ARCHITECTURAL / SER22
TYPE A2 em - 120/277V
(please advise shielding & reflector)
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
PHOTOMETRIC DATA
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER22-217G-CP-EU
SER Serrano,
Recessed
Architectural
2 x 2 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2P32-SC
0.88
F17T8
1325
31
Recessed
0° = 90 90° = 90
0° = 1.21 90° = 1.54
Length:1.79
Width:1.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.)
COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2238
2098
2003
1938
1840
1684
1505
1322
1163
1003
814
641
2238
2265
2226
2114
1953
1776
1604
1446
1287
1143
984
754
2238
2595
2544
2389
2214
2040
1880
1734
1604
1473
1325
943
2238
2838
2720
2556
2382
2217
2064
1921
1787
1651
1438
754
2238
2925
2775
2602
2428
2269
2116
1983
1854
1714
1457
679
Total Luminaire Efficiency
76.8%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
58
Yes-VDT Normal Use
$4.14 based on 3000
hrs. and $0.08 per
KWH
ZONAL LUMEN SUMMARY
0-30
0-40
0-60
0-90
0-180
RC
RW
1
2
3
4
5
6
7
8
9
10
70
84
77
70
64
59
55
51
47
44
41
80
50 30
80 77
70 65
62 56
55 49
49 43
44 38
40 34
37 30
34 27
31 25
10
74
61
51
43
38
33
29
26
23
21
70
82
75
68
62
57
53
49
46
43
40
70
50 30
79 76
69 64
61 55
54 48
48 42
44 37
40 33
36 30
33 27
31 25
10
73
60
51
43
37
33
29
26
23
21
50
75
66
59
52
47
42
38
35
32
30
50
30
73
62
54
47
41
37
33
30
27
25
0
0
65
55
46
40
34
30
27
24
21
19
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
75
400
Lumens % Lamp % Fixt.
575
971
1671
2033
2035
10
71
59
50
43
37
32
29
26
23
21
INDOOR CANDELA PLOT
ENERGY DATA
Zone
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
Test 4431 Test Date 9/9/2011
21.7
36.6
63.1
76.7
76.8
60
28.3
47.7
82.1
99.9
100.0
800
0
15
0.0
Page 2/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
30
Horiz 0-180
45.0
45
90.0
RECESSED ARCHITECTURAL / SER22
(please advise shielding & reflector)
TYPE A2 em - 120/277V
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
DIMENSIONAL DATA - GRID
CEILING COMPATIBILITY
Type G
FKCR
45/16"
24"
Side
End
For lay-in installation in exposed grid
ceilings. Maximum tee widths of 1" and
maximum tee heights of 2" allowed.
24"
For flanged fixtures in row configurations, the FKCR adapter bracket
kit is required in addition to the FK22 kit. Order one less FKCR than
the total number of fixtures in row. (Example: Row of two, order (2)
FK22 & (1) FKCR)
FK22 Flange Kit
24"
DIMENSIONAL DATA - SURFACE MOUNT
Side
25"
81⁄2"
O
End
For hard ceiling applications, order FK22
flange kit. Flange kit wires directly into
concealed ceiling opening for a clean,
finished appearance.
1⁄2"
Row cut out dimensions using FK22s & FKCR adapters:
Width 243/8", Length [24" × (# in row)] + 3/8".
Example: (24" × 2) + 3/8" = 483/8"
Flange kit cut out dimension for single unit only: 243/8" × 243/8"
25"
81⁄2"
4"
1113⁄32"
23⁄4"
7"
O
11⁄2"
25"
45⁄8"
NOTE: All dimensions are in inches; dimensions and
specifications are subject to change without
notice. Please consult factory or check sample for
verification.
Page 3/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER22
Electrical Options
TYPE A2 em - 120/277V
Emergency Battery Packs Installed
Technical
Luminaires with factory installed battery packs will bear the UL Emergency equipment label. Dry location labeling standard. Standard inverter
options below are not suitable for cold temperature starting, damp or wet location labeling. Optional inverters available for these applications.
Consult factory or specify vendor’s catalog number.
EL
EL61
EL71
EL72
350-450 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
500-600 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
600-700 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
600-700 total lumens for two 2'-8' lamps (T8, T12, U-Bent)
EL141
EL142
EL5*
EL5H*
1100-1400 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
1100-1400 total lumens for two 2'-4' lamps
390-700 lumens for one 2'-4' T5/T5HO
725-1250 lumens for one 2'-4' T5/T5HO
*These inverters not available in some 2' fixtures due to space constraints. Remote mounting using accessory enclosure (by others) recommended.
Fusing
Fusing is available on all fixtures to prevent over current from being transmitted upstream through the fixture as may be possible due to a dead
short fault in a ballast. Specify GLR (fast blow) or GMF (slow blow) fusing options. Fuses are not UL listed to break under load and therefore are
not a substitute for the in-fixture ballast disconnects supplied standard where required by the National Electric Code.
Fixture Flex and Leads
Fixture flex (also called pre-wire or whip) is a UL listed lighting component for recessed fixtures to provide the electrical wiring between the
junction box and recessed fixture. Flex may be no longer than 6'. Typical cables use ⅜" flexible conduit and three or four 18 gauge leads. Three
wires provides one line voltage hot lead. Add a wire for each separate hot lead required including separately switched ballasts, switch dim
ballast or battery pack to be powered through the flex cable. Flex cables are shipped pre-wired to the recessed fixture. Add option designation
to catalog number after ballast options. Eg. C388. Wire colors will be coded black/white/red/yellow plus a ground for line voltages. 588DIMM is
available with black/white violet, grey and ground for use with low voltage dimming leads.
Cable
No. of Wires
C Cable
Cable Diameter
3 3
4 4
5 5
8 ⅜"
2 ½"
Wire gauge
8 18 gauge
4 14 gauge
2 12 gauge
Miscellaneous Fixtures and Electrical Options (add As Suffix on end of Catalog string)
Fixture/Option
Cat. No.
PSW
PSWD
4PSW
Description
Pull switch, one circuit, 120V only
Pull switch, wired to the downlight circuit on a two circuit unit, 120V only
Four-way pull switch for two circuit, two lamp unit, 120V only
For Use With
Selected strips, surface units
and industrials. Contact factory
for applications
NL
Medium base lampholder for 15W, 25W, 40W, or 60W T10 lamp. Lamp not
included. 120V only
AWN, SM units
Fluorescent Night Light for 7W, T-4, G23 lamp
Fluorescent Night Light for 9W, T-4, G23 lamp
Fluorescent Night Light for 13W, T-4, GX23 lamp
Lamp not included. PL ballast will default to fixture voltage unless specified
Grounded convenience outlet (120V only)
4PS, SM, and WAL series
PL7
PL9
PL13
GCO
C6P15_ 6' Cord and Straight Blade, NEMA 5-15P, 15A (Add Voltage: 1 = 120)
C6TL15_ 6' Cord and Twist-Lock Plug, NEMA L5-15P (120V) NEMA L7-15P (277V), 15A
(Add Voltage: 1 = 120, 2 =277)
C6TL20_ 6' Cord and Twist-Lock Plug, NEMA L5-20P (120V) NEMA L7-20P (277V), 20A
(Add Voltage: 1 = 120, 2 =277)
F3C_
3-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
F4C_
4-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
GLR
Fast blow fuse, fuse amps based on fixture ordered
112
WPM, WM, WAL, UCS and UC
Standard on SA, W
All industrial fixtures
All industrial fixtures
All fixtures
TYPE A2 - 120/277V
(please advise shielding & reflector)
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
PROJECT INFORMATION
FEATURES
•
•
•
•
•
•
•
•
•
•
Architecturally enhanced triple lens design
Full distribution provides controlled high angle light for visual comfort and
more inviting spaces
Advanced optics produce high efficiencies
Hinged optical system allows easy access to lamps and electrical from below
the ceiling
Lenses interlock for structural integrity
Two optional lens aesthetics
Exclusive optional T8 EnergyMax® tuned 1.04 ballast factor ballast
Step and full dimming options for both T5 and T8 expand energy savings
opportunities
Most configurations produce low W/ft2 to meet the most restrictive lighting
power density codes
Available with exclusive wiHUBB technology preinstalled
Made with 90% recycled steel
Made of 80% recyclable materials by weight
Job pack available for minimizing amount of packaging material at job site
Individual cartons made of 100% recycled corrugated
Please go to http://www.hsi/productsustain.com for Hubbell Sustainable
Design Solutions Feature Criteria.
*
ORDERING INFORMATION
SER
22 – 2
17
MODEL
G
CEILING TYPE
G Grid
SM Surface Mount
For hard ceilings use
flange kit.
SIZE
ACCESSORIES
(ORDER
SEPARATELY)
FK22 2' × 2' Single
Flange Kit
FKCR Flange Kit Row
Adaptor
ELECTRICAL
Standard class “P”, thermally protected, autoresetting
HPF ballast, sound rated A. CEE NEMA Premium compliant.
All ballast leads extend a minimum of 6" through access
location. NEC/CEC-compliant ballast disconnect is standard.
FINISH
All visible parts are custom formulated soft, non-glare
high-reflectance white powder coat finish, painted after
fabrication.
EMERGENCY
Field installation of battery packs requires use of remote
test switch.
INSTALLATION
An access plate is furnished with each recessed fixture for
fast wiring connections without the necessity to open the
fixture or wireway.
BALLASTS
Energy efficient, thermally protected, automatic
resetting, Class P, high power factor, sound rated A,
magnetic or electronic ballasts. CEE NEMA Premium
compliant.
X
SHIELDING
C Contour
R Rail
LAMP TYPE
14
17
24
40TT
2', T5: 14 Watt
2', T8: 17 Watt
2', T5HO: 24 Watt
Twin Tube Compact, 2G11
Base: 40 Watt
CEILING COMPATIBILITY
Luminaire is available to fit exposed grid ceilings, or hard
ceilings when a flange kit is ordered. Some options may
increase fixture depth. For information on compatibility
with specific ceilings, or where plenum depth is a problem,
contact your Columbia Lighting representative. Four integral
T-bar clips are standard.
CERTIFICATION
All luminaires are built to UL 1598 standards and bear
appropriate UL and cUL or CSA labels. IC Rating optional for
some configurations. Damp location labeling is standard.
Emergency-equipped fixtures labeled UL 924.
–
X
E
REFLECTOR
P Performance
F Full
–
U
EP95
EP115
ESD115
ETT
EPTT
Electronic T8, 0.88 Ballast Factor, Instant Start
Electronic T8, T5, T5HO Dimming, Programmed Start 1
Electronic T8, 0.88 Ballast Factor, Step Dimming, Programmed Start
Electronic T8, 0.77 Ballast Factor, Low Wattage, Instant Start
Electronic T8, 1.18 Ballast Factor, High Wattage, Instant Start
Electronic T8, 1.04 Ballast Factor, Instant Start (N/A 1-Lamp)
Electronic T8, 1.04 Ballast Factor, Step Dimming, Programmed Start
Electronic T8, 1.04 Ballast Factor, Programmed Start
Electronic T5, T5HO, 1.0 Ballast Factor or T8,
0.88 Ballast Factor, Programmed Start
Electronic T5, 0.95 Ballast Factor , Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 0.95 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO, 1-Lamp)
Electronic T5, 1.15 Ballast Factor, Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 1.15 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO)
Electronic Twin Tube, Instant Start
Electronic Twin Tube, Programmed Start
Page 1/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
–
VOLTAGE
EL141ST
OPTIONS
C388
C488
C588
EL
GLR
GMF
NYC
WIH
IC
U 120V-277V
347 347V2
BALLAST
E
ED
ESD
ELW
EHL
E104
ESD104
EP104
EP
ESD95
Damp Label - standard
1
Where available.
2
Not available with surface mount.
Date
CONSTRUCTION
Luminaire housing, end caps, and reflectors are die-formed
code-gauge cold-rolled steel. Optical system hinges for easy
access to lamps and electrical components. Mechanical light
trap prevents light leaks. Latches are spring loaded.
–
1 One
(N/A 17, 14, 24)
2 Two
3 Three
(N/A TT)
22 2' × 2'
Catalog No.
EXAMPLE SER22-314G-CP-EPU
NO. OF LAMPS
SER Serrano®
Recessed
Architectural
Luminaire
Type
SHIELDING
Lenses are high transmission extruded acrylic.
HUBBELL SUSTAINABLE DESIGN SOLUTION FEATURES*
•
•
•
•
Project Name
3-Wire Flex
4-Wire Flex
5-Wire Flex
Emergency Battery Pack
Fast Blow Fuse
Slow Blow Fuse
NYC Compliant
wiHUBB Enabled 2
IC Rating
LAMPS
FO730
FO735
FO741
FO830
FO835
FO841
F5830
F5835
F5841
FTT830
FTT835
FTT841
30K 75CRI T8 Lamps Installed
35K 75CRI T8 Lamps Installed
41K 75CRI T8 Lamps Installed
30K 82CRI T8 Lamps Installed
35K 82CRI T8 Lamps Installed
41K 82CRI T8 Lamps Installed
30K 85CRI T5 or T5HO Lamps Installed
35K 85CRI T5 or T5HO Lamps Installed
41K 85CRI T5 or T5HO Lamps Installed
30K Twin Tube Lamps Installed
35K Twin Tube Lamps Installed
41K Twin Tube Lamps Installed
RECESSED ARCHITECTURAL / SER22
TYPE A2 - 120/277V
(please advise shielding & reflector)
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
PHOTOMETRIC DATA
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER22-217G-CP-EU
SER Serrano,
Recessed
Architectural
2 x 2 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2P32-SC
0.88
F17T8
1325
31
Recessed
0° = 90 90° = 90
0° = 1.21 90° = 1.54
Length:1.79
Width:1.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.)
COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2238
2098
2003
1938
1840
1684
1505
1322
1163
1003
814
641
2238
2265
2226
2114
1953
1776
1604
1446
1287
1143
984
754
2238
2595
2544
2389
2214
2040
1880
1734
1604
1473
1325
943
2238
2838
2720
2556
2382
2217
2064
1921
1787
1651
1438
754
2238
2925
2775
2602
2428
2269
2116
1983
1854
1714
1457
679
Total Luminaire Efficiency
76.8%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
58
Yes-VDT Normal Use
$4.14 based on 3000
hrs. and $0.08 per
KWH
ZONAL LUMEN SUMMARY
0-30
0-40
0-60
0-90
0-180
RC
RW
1
2
3
4
5
6
7
8
9
10
70
84
77
70
64
59
55
51
47
44
41
80
50 30
80 77
70 65
62 56
55 49
49 43
44 38
40 34
37 30
34 27
31 25
10
74
61
51
43
38
33
29
26
23
21
70
82
75
68
62
57
53
49
46
43
40
70
50 30
79 76
69 64
61 55
54 48
48 42
44 37
40 33
36 30
33 27
31 25
10
73
60
51
43
37
33
29
26
23
21
50
75
66
59
52
47
42
38
35
32
30
50
30
73
62
54
47
41
37
33
30
27
25
0
0
65
55
46
40
34
30
27
24
21
19
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
75
400
Lumens % Lamp % Fixt.
575
971
1671
2033
2035
10
71
59
50
43
37
32
29
26
23
21
INDOOR CANDELA PLOT
ENERGY DATA
Zone
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
Test 4431 Test Date 9/9/2011
21.7
36.6
63.1
76.7
76.8
60
28.3
47.7
82.1
99.9
100.0
800
0
15
0.0
Page 2/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
30
Horiz 0-180
45.0
45
90.0
RECESSED ARCHITECTURAL / SER22
(please advise shielding & reflector)
TYPE A2 - 120/277V
SER22
2' × 2' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8, TT
DIMENSIONAL DATA - GRID
CEILING COMPATIBILITY
Type G
FKCR
45/16"
24"
Side
End
For lay-in installation in exposed grid
ceilings. Maximum tee widths of 1" and
maximum tee heights of 2" allowed.
24"
For flanged fixtures in row configurations, the FKCR adapter bracket
kit is required in addition to the FK22 kit. Order one less FKCR than
the total number of fixtures in row. (Example: Row of two, order (2)
FK22 & (1) FKCR)
FK22 Flange Kit
24"
DIMENSIONAL DATA - SURFACE MOUNT
Side
25"
81⁄2"
O
End
For hard ceiling applications, order FK22
flange kit. Flange kit wires directly into
concealed ceiling opening for a clean,
finished appearance.
1⁄2"
Row cut out dimensions using FK22s & FKCR adapters:
Width 243/8", Length [24" × (# in row)] + 3/8".
Example: (24" × 2) + 3/8" = 483/8"
Flange kit cut out dimension for single unit only: 243/8" × 243/8"
25"
81⁄2"
4"
1113⁄32"
23⁄4"
7"
O
11⁄2"
25"
45⁄8"
NOTE: All dimensions are in inches; dimensions and
specifications are subject to change without
notice. Please consult factory or check sample for
verification.
Page 3/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER22
TYPE A4 em - 120/277V
(please advise shielding & reflector)
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
PROJECT INFORMATION
FEATURES
•
•
•
•
•
•
•
•
•
•
Architecturally enhanced triple lens design
Full distribution provides controlled high angle light for visual comfort and
more inviting spaces
Advanced optics produce high efficiencies
Hinged optical system allows easy access to lamps and electrical from below
the ceiling
Lenses interlock for structural integrity
Two optional lens aesthetics
Exclusive optional T8 EnergyMax® tuned 1.04 ballast factor ballast
Step and full dimming options for both T5 and T8 expand energy savings
opportunities
Most configurations produce low W/ft2 to meet the most restrictive lighting
power density codes
Available with exclusive wiHUBB technology preinstalled
HUBBELL SUSTAINABLE DESIGN SOLUTION FEATURES*
•
•
•
•
Project Name
Type
Catalog No.
Date
CONSTRUCTION
Luminaire housing, end caps, and reflectors are die-formed
code-gauge cold-rolled steel. Optical system hinges for easy
access to lamps and electrical components. Mechanical light
trap prevents light leaks. Latches are spring loaded.
ELECTRICAL
Standard class “P”, thermally protected, autoresetting
HPF ballast, sound rated A. CEE NEMA Premium compliant.
All ballast leads extend a minimum of 6" through access
location. NEC/CEC-compliant ballast disconnect is standard.
FINISH
All visible parts are custom formulated soft, non-glare
high-reflectance white powder coat finish, painted after
fabrication.
EMERGENCY
Field installation of battery packs requires use of remote
test switch.
SHIELDING
Lenses are high transmission extruded acrylic.
INSTALLATION
An access plate is furnished with each recessed fixture for
fast wiring connections without the necessity to open the
fixture or wireway.
Made with 90% recycled steel
Made of 80% recyclable materials by weight
BALLASTS
Job pack available for minimizing amount of packaging material at job site Energy efficient, thermally protected, automatic
Individual cartons made of 100% recycled corrugated
resetting, Class P, high power factor, sound rated A,
Please go to http://www.hsi/productsustain.com for Hubbell Sustainable
Design Solutions Feature Criteria.
*
ORDERING INFORMATION
SER
24 – 2
17
MODEL
NO. OF
LAMPS
SER Serrano®
Recessed
Architectural
Luminaire
SIZE
24 2' × 4'
1 One
2 Two
3 Three
28 4', T5: 28 Watt
32 4', T8: 32, 30, 28, or
25 Watt
54 4', T5HO: 54 or 51
Watt
ACCESSORIES
(ORDER
SEPARATELY)
FK24 2' × 4' Single
Flange Kit
FKCR Flange Kit Row
Adaptor
EP95
EP115
Not compatible with T8 25, 28, or 30 watt energy
savings lamps.
2
Where available.
3
Not recommended for use with step or full dimming.
4
Not available with surface mount.
–
X
SHIELDING
C Contour
R Rail
X
–
E
REFLECTOR
ESD115
1
ESD80
Electronic T8, 0.88 Ballast Factor, Instant Start
Electronic T8, T5, T5HO Dimming, Programmed Start1, 2
Electronic T8, 0.88 Ballast Factor, Step Dimming, Programmed Start 1
Electronic T8, 0.77 Ballast Factor, Low Wattage, Instant Start
Electronic T8, 1.18 Ballast Factor, High Wattage, Instant Start
Electronic T8, 1.04 Ballast Factor, Instant Start (N/A 1-Lamp)
Electronic T8, 1.04 Ballast Factor, Step Dimming, Programmed Start1
Electronic T8, 1.04 Ballast Factor, Programmed Start
Electronic T5, T5HO, 1.0 Ballast Factor or T8,
0.88 Ballast Factor, Programmed Start
Electronic T5, 0.95 Ballast Factor , Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 0.95 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO, 1-Lamp)
Electronic T5, 1.15 Ballast Factor, Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 1.15 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO)
Electronic T5HO, 0.80 Ballast Factor, Step Dimming, Programmed
Start (2-Lamp 54W only)
Page 1/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
U
–
–
VOLTAGE
P Performance
F Full
LAMPS
FO730
FO735
FO741
FO830
FO835
FO841
F028830
F028835
F028841
FOH830
FOH835
FOH841
F5830
F5835
F5841
F5H830
F5H835
F5H841
EL141ST
OPTIONS
C388
C488
C588
EL141
U 120V-277V
347 347V2
BALLAST
ESD95
Damp Label - standard
G
G Grid
SM Surface Mount
For hard ceilings use
flange kit.
E
ED
ESD
ELW
EHL
E104
ESD104
EP104
EP
CERTIFICATION
All luminaires are built to UL 1598 standards and bear
appropriate UL and cUL or CSA labels. IC Rating optional for
some configurations. Damp location labeling is standard.
Emergency-equipped fixtures labeled UL 924.
EXAMPLE SER24-232G-RF-E104U-F0835
CEILING TYPE
LAMP TYPE
magnetic or electronic ballasts. CEE NEMA Premium
compliant.
CEILING COMPATIBILITY
Luminaire is available to fit exposed grid ceilings, or hard
ceilings when a flange kit is ordered. Some options may
increase fixture depth. For information on compatibility
with specific ceilings, or where plenum depth is a problem,
contact your Columbia Lighting representative. Four integral
T-bar clips are standard.
30K 75CRI T8 Lamps Installed
35K 75CRI T8 Lamps Installed
41K 75CRI T8 Lamps Installed
30K 82CRI T8 Lamps Installed
35K 82CRI T8 Lamps Installed
41K 82CRI T8 Lamps Installed
30K 82CRI 28W T8 Lamps Installed 3
35K 82CRI 28W T8 Lamps Installed 3
41K 82CRI 28W T8 Lamps Installed 3
30K High Lumen T8 Lamps Installed
35K High Lumen T8 Lamps Installed
41K High Lumen T8 Lamps Installed
30K 85CRI T5 or T5HO Lamps Installed
35K 85CRI T5 or T5HO Lamps Installed
41K 85CRI T5 or T5HO Lamps Installed
30K High Lumen T5 Lamps Installed
35K High Lumen T5 Lamps Installed
41K High Lumen T5 Lamps Installed
GLR
GMF
NYC
WIH
IC
3-Wire Flex
4-Wire Flex
5-Wire Flex
Emergency (self test)
Battery Pack
Fast Blow Fuse
Slow Blow Fuse
NYC Compliant
wiHUBB Enabled 4
IC Rating
RECESSED ARCHITECTURAL / SER24
TYPE A4 em - 120/277V
(please advise shielding & reflector)
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
PHOTOMETRIC DATA
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER24-232G-CP-EU
SER Serrano,
Recessed
Architectural
2 x 4 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2P32-SC
0.88
F28T8
2725
50
Recessed
0° = 90 90° = 90
0° = 1.23 90° = 1.55
Length:1.83
Width:3.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.) COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2417
2309
2229
2183
2119
2005
1843
1653
1464
1276
1061
811
2417
2451
2476
2415
2289
2126
1963
1802
1639
1478
1318
1145
2417
2761
2821
2711
2559
2396
2239
2093
1949
1816
1707
1198
2417
3022
3007
2867
2700
2533
2374
2228
2079
1940
1689
811
2417
3105
3047
2891
2717
2544
2383
2224
2070
1923
1574
634
ZONAL LUMEN SUMMARY
Zone
0-30
0-40
0-60
0-90
0-180
24.1
41.0
72.5
89.5
89.5
RC
RW
1
2
3
4
5
6
7
8
9
10
70
98
89
81
74
68
63
58
54
51
47
80
50 30
93 90
82 76
72 64
64 56
57 49
51 43
46 38
42 34
39 31
36 28
10
86
71
59
50
43
37
33
29
26
24
70
95
87
79
72
66
61
57
53
49
46
70
50 30
91 88
80 74
70 64
62 55
56 48
50 43
45 38
41 34
38 31
35 28
10
85
70
58
49
43
37
33
29
26
24
50
88
77
68
60
54
49
44
40
37
34
50
30
85
72
62
54
47
42
37
34
31
28
INDOOR CANDELA PLOT
10
82
68
57
49
42
37
32
29
26
24
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
0
0
75
63
53
45
39
34
30
27
24
22
90
75
900
60
1800
0
15
0.0
ENERGY DATA
Lumens % Lamp % Fixt.
1314
2237
3951
4879
4879
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
Test 4460 Test Date 9/19/2011
26.9
45.8
81.0
100.0
100.0
Total Luminaire Efficiency
89.5%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
86
Noncompliant
$2.79 based on
3000 hrs. and
$0.08 per KWH
30
Horiz 0-180
45.0
45
90.0
Test 4540 Test Date 10/25/2011
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER24-228G-CP-EPU
SER Serrano,
Recessed
Architectural
2 x 4 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2S28-N
1.00
F28T5
2625
62
Recessed
0° = 90 90° = 90
0° = 1.22 90° = 1.51
Length:3.83
Width:1.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.) COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2459
2321
2215
2146
2069
1944
1769
1599
1423
1234
1017
775
2459
2451
2442
2370
2236
2072
1898
1737
1581
1424
1247
1093
2459
2727
2757
2648
2506
2348
2184
2039
1899
1774
1636
1093
2459
2961
2949
2808
2645
2471
2297
2148
2003
1869
1592
740
2459
3043
2977
2819
2645
2466
2294
2144
2003
1845
1486
564
ZONAL LUMEN SUMMARY
Zone
0-30
0-40
0-60
0-90
0-180
Lumens % Lamp % Fixt.
1316
2224
3899
4796
4796
25.1
42.4
74.3
91.4
91.4
27.4
46.4
81.3
100.0
100.0
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
RC
RW 70
1 100
2
91
3 83
4
76
5 70
6 64
7 60
8 56
9 52
10 49
80
50 30
95 92
83 77
73 66
65 57
58 50
52 44
47 39
43 35
40 32
37 29
10
88
72
60
51
44
38
34
30
27
24
70
97
88
81
74
68
63
58
54
51
47
70
50 30
93 90
82 76
72 65
64 56
57 49
51 44
47 39
43 35
39 32
36 29
10
87
71
60
51
44
38
34
30
27
24
50
90
78
69
62
55
50
45
41
38
35
50
30
87
74
63
55
48
43
38
35
31
29
INDOOR CANDELA PLOT
10
84
70
59
50
43
38
33
30
27
24
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
0
0
77
65
55
47
40
35
31
28
25
22
90
75
900
60
1800
15
0
0.0
30
Horiz 0-180
45.0
45
90.0
ENERGY DATA
Total Luminaire Efficiency
91.4%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
77
Noncompliant
$3.12 based on
3000 hrs. and
$0.08 per KWH
Page 2/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER24
(please advise shielding & reflector)
TYPE A4 em - 120/277V
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
DIMENSIONAL DATA
CEILING COMPATIBILITY
Type G
FKCR
45/16"
24"
Side
End
For lay-in installation in exposed grid
ceilings. Maximum tee widths of 1" and
maximum tee heights of 2" allowed.
24" 24"
For flanged fixtures in row configurations, the FKCR adapter bracket
kit is required in addition to the FK24 kit. Order one less FKCR than
the total number of fixtures in row. (Example: Row of two, order (2)
FK24 & (1) FKCR)
FK24 Flange Kit
48"
48"
DIMENSIONAL DATA - SURFACE MOUNT
81⁄2"
25"
Side
End
For hard ceiling applications, order FK24
flange kit. Flange kit wires directly into
concealed ceiling opening for a clean,
finished appearance.
O 1⁄2"
Row cut out dimensions using FK24s & FKCR adapters:
Width 243/8", Length [48" × (# in row)] + 3/8".
Example: (48" × 2) + 3/8" = 963/8"
Flange kit cut out dimension for single unit only: 243/8" × 483/8"
49"
193⁄4"
221⁄2"
23⁄4"
4"
71⁄2"
O 11⁄2"
25"
45⁄8"
NOTE: All dimensions are in inches; dimensions and
specifications are subject to change without
notice. Please consult factory or check sample for
verification.
Page 3/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER24
Electrical Options
TYPE A4 em - 120/277V
Emergency Battery Packs Installed
Technical
Luminaires with factory installed battery packs will bear the UL Emergency equipment label. Dry location labeling standard. Standard inverter
options below are not suitable for cold temperature starting, damp or wet location labeling. Optional inverters available for these applications.
Consult factory or specify vendor’s catalog number.
EL
EL61
EL71
EL72
350-450 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
500-600 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
600-700 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
600-700 total lumens for two 2'-8' lamps (T8, T12, U-Bent)
EL141
EL142
EL5*
EL5H*
1100-1400 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
1100-1400 total lumens for two 2'-4' lamps
390-700 lumens for one 2'-4' T5/T5HO
725-1250 lumens for one 2'-4' T5/T5HO
*These inverters not available in some 2' fixtures due to space constraints. Remote mounting using accessory enclosure (by others) recommended.
Fusing
Fusing is available on all fixtures to prevent over current from being transmitted upstream through the fixture as may be possible due to a dead
short fault in a ballast. Specify GLR (fast blow) or GMF (slow blow) fusing options. Fuses are not UL listed to break under load and therefore are
not a substitute for the in-fixture ballast disconnects supplied standard where required by the National Electric Code.
Fixture Flex and Leads
Fixture flex (also called pre-wire or whip) is a UL listed lighting component for recessed fixtures to provide the electrical wiring between the
junction box and recessed fixture. Flex may be no longer than 6'. Typical cables use ⅜" flexible conduit and three or four 18 gauge leads. Three
wires provides one line voltage hot lead. Add a wire for each separate hot lead required including separately switched ballasts, switch dim
ballast or battery pack to be powered through the flex cable. Flex cables are shipped pre-wired to the recessed fixture. Add option designation
to catalog number after ballast options. Eg. C388. Wire colors will be coded black/white/red/yellow plus a ground for line voltages. 588DIMM is
available with black/white violet, grey and ground for use with low voltage dimming leads.
Cable
No. of Wires
C Cable
Cable Diameter
3 3
4 4
5 5
8 ⅜"
2 ½"
Wire gauge
8 18 gauge
4 14 gauge
2 12 gauge
Miscellaneous Fixtures and Electrical Options (add As Suffix on end of Catalog string)
Fixture/Option
Cat. No.
PSW
PSWD
4PSW
Description
Pull switch, one circuit, 120V only
Pull switch, wired to the downlight circuit on a two circuit unit, 120V only
Four-way pull switch for two circuit, two lamp unit, 120V only
For Use With
Selected strips, surface units
and industrials. Contact factory
for applications
NL
Medium base lampholder for 15W, 25W, 40W, or 60W T10 lamp. Lamp not
included. 120V only
AWN, SM units
Fluorescent Night Light for 7W, T-4, G23 lamp
Fluorescent Night Light for 9W, T-4, G23 lamp
Fluorescent Night Light for 13W, T-4, GX23 lamp
Lamp not included. PL ballast will default to fixture voltage unless specified
Grounded convenience outlet (120V only)
4PS, SM, and WAL series
PL7
PL9
PL13
GCO
C6P15_ 6' Cord and Straight Blade, NEMA 5-15P, 15A (Add Voltage: 1 = 120)
C6TL15_ 6' Cord and Twist-Lock Plug, NEMA L5-15P (120V) NEMA L7-15P (277V), 15A
(Add Voltage: 1 = 120, 2 =277)
C6TL20_ 6' Cord and Twist-Lock Plug, NEMA L5-20P (120V) NEMA L7-20P (277V), 20A
(Add Voltage: 1 = 120, 2 =277)
F3C_
3-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
F4C_
4-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
GLR
Fast blow fuse, fuse amps based on fixture ordered
112
WPM, WM, WAL, UCS and UC
Standard on SA, W
All industrial fixtures
All industrial fixtures
All fixtures
TYPE A4 - 120/277V
(please advise shielding & reflector)
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
PROJECT INFORMATION
FEATURES
•
•
•
•
•
•
•
•
•
•
Architecturally enhanced triple lens design
Full distribution provides controlled high angle light for visual comfort and
more inviting spaces
Advanced optics produce high efficiencies
Hinged optical system allows easy access to lamps and electrical from below
the ceiling
Lenses interlock for structural integrity
Two optional lens aesthetics
Exclusive optional T8 EnergyMax® tuned 1.04 ballast factor ballast
Step and full dimming options for both T5 and T8 expand energy savings
opportunities
Most configurations produce low W/ft2 to meet the most restrictive lighting
power density codes
Available with exclusive wiHUBB technology preinstalled
HUBBELL SUSTAINABLE DESIGN SOLUTION FEATURES*
•
•
•
•
Project Name
Type
Catalog No.
Date
CONSTRUCTION
Luminaire housing, end caps, and reflectors are die-formed
code-gauge cold-rolled steel. Optical system hinges for easy
access to lamps and electrical components. Mechanical light
trap prevents light leaks. Latches are spring loaded.
ELECTRICAL
Standard class “P”, thermally protected, autoresetting
HPF ballast, sound rated A. CEE NEMA Premium compliant.
All ballast leads extend a minimum of 6" through access
location. NEC/CEC-compliant ballast disconnect is standard.
FINISH
All visible parts are custom formulated soft, non-glare
high-reflectance white powder coat finish, painted after
fabrication.
EMERGENCY
Field installation of battery packs requires use of remote
test switch.
SHIELDING
Lenses are high transmission extruded acrylic.
INSTALLATION
An access plate is furnished with each recessed fixture for
fast wiring connections without the necessity to open the
fixture or wireway.
Made with 90% recycled steel
Made of 80% recyclable materials by weight
BALLASTS
Job pack available for minimizing amount of packaging material at job site Energy efficient, thermally protected, automatic
Individual cartons made of 100% recycled corrugated
resetting, Class P, high power factor, sound rated A,
Please go to http://www.hsi/productsustain.com for Hubbell Sustainable
Design Solutions Feature Criteria.
*
ORDERING INFORMATION
SER
24 – 2
17
MODEL
NO. OF
LAMPS
SER Serrano®
Recessed
Architectural
Luminaire
SIZE
24 2' × 4'
1 One
2 Two
3 Three
28 4', T5: 28 Watt
32 4', T8: 32, 30, 28, or
25 Watt
54 4', T5HO: 54 or 51
Watt
ACCESSORIES
(ORDER
SEPARATELY)
FK24 2' × 4' Single
Flange Kit
FKCR Flange Kit Row
Adaptor
EP95
EP115
Not compatible with T8 25, 28, or 30 watt energy
savings lamps.
2
Where available.
3
Not recommended for use with step or full dimming.
4
Not available with surface mount.
–
X
SHIELDING
C Contour
R Rail
X
–
E
REFLECTOR
ESD115
1
ESD80
Electronic T8, 0.88 Ballast Factor, Instant Start
Electronic T8, T5, T5HO Dimming, Programmed Start1, 2
Electronic T8, 0.88 Ballast Factor, Step Dimming, Programmed Start 1
Electronic T8, 0.77 Ballast Factor, Low Wattage, Instant Start
Electronic T8, 1.18 Ballast Factor, High Wattage, Instant Start
Electronic T8, 1.04 Ballast Factor, Instant Start (N/A 1-Lamp)
Electronic T8, 1.04 Ballast Factor, Step Dimming, Programmed Start1
Electronic T8, 1.04 Ballast Factor, Programmed Start
Electronic T5, T5HO, 1.0 Ballast Factor or T8,
0.88 Ballast Factor, Programmed Start
Electronic T5, 0.95 Ballast Factor , Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 0.95 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO, 1-Lamp)
Electronic T5, 1.15 Ballast Factor, Programmed Start (N/A T5HO,
1-Lamp)
Electronic T5, 1.15 Ballast Factor,
Step Dimming, Programmed Start (N/A T5HO)
Electronic T5HO, 0.80 Ballast Factor, Step Dimming, Programmed
Start (2-Lamp 54W only)
Page 1/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
U
–
–
VOLTAGE
P Performance
F Full
LAMPS
FO730
FO735
FO741
FO830
FO835
FO841
F028830
F028835
F028841
FOH830
FOH835
FOH841
F5830
F5835
F5841
F5H830
F5H835
F5H841
EL141ST
OPTIONS
C388
C488
C588
EL
U 120V-277V
347 347V2
BALLAST
ESD95
Damp Label - standard
G
G Grid
SM Surface Mount
For hard ceilings use
flange kit.
E
ED
ESD
ELW
EHL
E104
ESD104
EP104
EP
CERTIFICATION
All luminaires are built to UL 1598 standards and bear
appropriate UL and cUL or CSA labels. IC Rating optional for
some configurations. Damp location labeling is standard.
Emergency-equipped fixtures labeled UL 924.
EXAMPLE SER24-232G-RF-E104U-F0835
CEILING TYPE
LAMP TYPE
magnetic or electronic ballasts. CEE NEMA Premium
compliant.
CEILING COMPATIBILITY
Luminaire is available to fit exposed grid ceilings, or hard
ceilings when a flange kit is ordered. Some options may
increase fixture depth. For information on compatibility
with specific ceilings, or where plenum depth is a problem,
contact your Columbia Lighting representative. Four integral
T-bar clips are standard.
30K 75CRI T8 Lamps Installed
35K 75CRI T8 Lamps Installed
41K 75CRI T8 Lamps Installed
30K 82CRI T8 Lamps Installed
35K 82CRI T8 Lamps Installed
41K 82CRI T8 Lamps Installed
30K 82CRI 28W T8 Lamps Installed 3
35K 82CRI 28W T8 Lamps Installed 3
41K 82CRI 28W T8 Lamps Installed 3
30K High Lumen T8 Lamps Installed
35K High Lumen T8 Lamps Installed
41K High Lumen T8 Lamps Installed
30K 85CRI T5 or T5HO Lamps Installed
35K 85CRI T5 or T5HO Lamps Installed
41K 85CRI T5 or T5HO Lamps Installed
30K High Lumen T5 Lamps Installed
35K High Lumen T5 Lamps Installed
41K High Lumen T5 Lamps Installed
GLR
GMF
NYC
WIH
IC
3-Wire Flex
4-Wire Flex
5-Wire Flex
Emergency
Battery Pack
Fast Blow Fuse
Slow Blow Fuse
NYC Compliant
wiHUBB Enabled 4
IC Rating
RECESSED ARCHITECTURAL / SER24
TYPE A4 - 120/277V
(please advise shielding & reflector)
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
PHOTOMETRIC DATA
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER24-232G-CP-EU
SER Serrano,
Recessed
Architectural
2 x 4 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2P32-SC
0.88
F28T8
2725
50
Recessed
0° = 90 90° = 90
0° = 1.23 90° = 1.55
Length:1.83
Width:3.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.) COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2417
2309
2229
2183
2119
2005
1843
1653
1464
1276
1061
811
2417
2451
2476
2415
2289
2126
1963
1802
1639
1478
1318
1145
2417
2761
2821
2711
2559
2396
2239
2093
1949
1816
1707
1198
2417
3022
3007
2867
2700
2533
2374
2228
2079
1940
1689
811
2417
3105
3047
2891
2717
2544
2383
2224
2070
1923
1574
634
ZONAL LUMEN SUMMARY
Zone
0-30
0-40
0-60
0-90
0-180
24.1
41.0
72.5
89.5
89.5
RC
RW
1
2
3
4
5
6
7
8
9
10
70
98
89
81
74
68
63
58
54
51
47
80
50 30
93 90
82 76
72 64
64 56
57 49
51 43
46 38
42 34
39 31
36 28
10
86
71
59
50
43
37
33
29
26
24
70
95
87
79
72
66
61
57
53
49
46
70
50 30
91 88
80 74
70 64
62 55
56 48
50 43
45 38
41 34
38 31
35 28
10
85
70
58
49
43
37
33
29
26
24
50
88
77
68
60
54
49
44
40
37
34
50
30
85
72
62
54
47
42
37
34
31
28
INDOOR CANDELA PLOT
10
82
68
57
49
42
37
32
29
26
24
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
0
0
75
63
53
45
39
34
30
27
24
22
90
75
900
60
1800
0
15
0.0
ENERGY DATA
Lumens % Lamp % Fixt.
1314
2237
3951
4879
4879
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
Test 4460 Test Date 9/19/2011
26.9
45.8
81.0
100.0
100.0
Total Luminaire Efficiency
89.5%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
86
Noncompliant
$2.79 based on
3000 hrs. and
$0.08 per KWH
30
Horiz 0-180
45.0
45
90.0
Test 4540 Test Date 10/25/2011
Ballast
Ballast Factor
Lamp
Lumens per
Lamp
Watts
Mounting
Shielding Angle
Spacing
Criterion
Luminous
Opening in Feet
SER24-228G-CP-EPU
SER Serrano,
Recessed
Architectural
2 x 4 2-lamp with
Contour center
lens, linear prismed
side lenses, and
performance
reflector
ICN-2S28-N
1.00
F28T5
2625
62
Recessed
0° = 90 90° = 90
0° = 1.22 90° = 1.51
Length:3.83
Width:1.83
Height:0.00
AVG. LUMINANCE (Candela/Sq. M.) COEFFICIENTS OF UTILIZATION (%)
0.0 22.5 45.0 67.5 90.0
0
30
40
45
50
55
60
65
70
75
80
85
2459
2321
2215
2146
2069
1944
1769
1599
1423
1234
1017
775
2459
2451
2442
2370
2236
2072
1898
1737
1581
1424
1247
1093
2459
2727
2757
2648
2506
2348
2184
2039
1899
1774
1636
1093
2459
2961
2949
2808
2645
2471
2297
2148
2003
1869
1592
740
2459
3043
2977
2819
2645
2466
2294
2144
2003
1845
1486
564
ZONAL LUMEN SUMMARY
Zone
0-30
0-40
0-60
0-90
0-180
Lumens % Lamp % Fixt.
1316
2224
3899
4796
4796
25.1
42.4
74.3
91.4
91.4
27.4
46.4
81.3
100.0
100.0
RCR
Luminaire
Average Luminance Angle
LUMINAIRE DATA
RC
RW 70
1 100
2
91
3 83
4
76
5 70
6 64
7 60
8 56
9 52
10 49
80
50 30
95 92
83 77
73 66
65 57
58 50
52 44
47 39
43 35
40 32
37 29
10
88
72
60
51
44
38
34
30
27
24
70
97
88
81
74
68
63
58
54
51
47
70
50 30
93 90
82 76
72 65
64 56
57 49
51 44
47 39
43 35
39 32
36 29
10
87
71
60
51
44
38
34
30
27
24
50
90
78
69
62
55
50
45
41
38
35
50
30
87
74
63
55
48
43
38
35
31
29
INDOOR CANDELA PLOT
10
84
70
59
50
43
38
33
30
27
24
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
0
0
77
65
55
47
40
35
31
28
25
22
90
75
900
60
1800
15
0
0.0
30
Horiz 0-180
45.0
45
90.0
ENERGY DATA
Total Luminaire Efficiency
91.4%
Luminaire Efficacy Rating (LER)
ANSI/IESNA RP-1-2004 Compliance
Comparative Yearly Lighting Energy
Cost per 1000 Lumens
77
Noncompliant
$3.12 based on
3000 hrs. and
$0.08 per KWH
Page 2/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER24
(please advise shielding & reflector)
TYPE A4 - 120/277V
SER24
2' × 4' High Efficiency, Serrano® Architectural Luminaire / 1, 2, 3-Lamp T5, T5HO, T8
DIMENSIONAL DATA
CEILING COMPATIBILITY
Type G
FKCR
45/16"
24"
Side
End
For lay-in installation in exposed grid
ceilings. Maximum tee widths of 1" and
maximum tee heights of 2" allowed.
24" 24"
For flanged fixtures in row configurations, the FKCR adapter bracket
kit is required in addition to the FK24 kit. Order one less FKCR than
the total number of fixtures in row. (Example: Row of two, order (2)
FK24 & (1) FKCR)
FK24 Flange Kit
48"
48"
DIMENSIONAL DATA - SURFACE MOUNT
81⁄2"
25"
Side
End
For hard ceiling applications, order FK24
flange kit. Flange kit wires directly into
concealed ceiling opening for a clean,
finished appearance.
O 1⁄2"
Row cut out dimensions using FK24s & FKCR adapters:
Width 243/8", Length [48" × (# in row)] + 3/8".
Example: (48" × 2) + 3/8" = 963/8"
Flange kit cut out dimension for single unit only: 243/8" × 483/8"
49"
193⁄4"
221⁄2"
23⁄4"
4"
71⁄2"
O 11⁄2"
25"
45⁄8"
NOTE: All dimensions are in inches; dimensions and
specifications are subject to change without
notice. Please consult factory or check sample for
verification.
Page 3/3 Rev. 01/02/14
© 2014 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
RECESSED ARCHITECTURAL / SER24
TYPE B - 120/277V
8" High Lumen LED
Downlight
Date:type:
firm name:
MD8LED
PROJECT:
120 - 277V, 347V
0-10V Dimming
APPLICATIONS:
Architektur MD8LED Series is a 8” specification
grade high output LED downlight capable
of delivering 12,000+ lumens designed for
ceiling heights from 20 to 60 feet. Combining
energy savings, long life, low maintenance cost
& controllability, it is an excellent alternative
to metal halide (up to 250 watts) and quartz
(up to 500 watts) fixtures. ENERGY STAR®
qualified. Rated for a minimum of 50,000
hours life with 70% Lumen maintenance up
to 40C (104F) when free airflow is available
around the fixture. Rated for a minimum of
60,000 hours life with 85% lumen maintenance
up to 30C (86F) when free airflow is available
around the fixture and no lens is present
HOUSING:
18 gauge corrosion protected steel platform
designed for accessibility. Pre-wired J-box
with snap-on covers. Separate power supply
module serviceable and removable from above
or below the ceiling. Power supply module
is connected to the LED light engine using a
locking plug-in connector. Approved for 8 (4
in/4 out) No. 12 AWG conductors rated for 90
C through wiring. Variable light engine mounts
allow reflectors to be interchanged in the field.
Reflector:
High purity spun aluminum self-flanged reflector
with iridescence suppressed Alzak anodized
finish. Available in specular, semi-specular,
and Prescolite’s American Matte finish in a
variety of anodized colors as well as painted
trim options. Offered in 25º, 35º, 45º, and 55º
optical distributions as well as lens options for
wet location applications. Easy to install yoke
mounting system with safety tether included.
LED Light Engine:
The MD8LED uses up to 480 individual Nichia
LEDs specifically mixed to provide a minimum
of 80 CRI with 3 SCDM color consistency.
The LED light engine is available in multiple
lumen packages and color temperatures to
Ceiling Cutout: 81/4"
Maximum Ceiling Thickness 11/4"
Consult factory for ceiling thickness to 2"
For conversion to millimeters,
multiply inches by 25.4
Not to Scale
accommodate any design requirement. The use of
individual LEDs to achieve these lumen packages
enables optimal thermal management while creating
a visually pleasing diffuse appearance in the ceiling.
The LED light engine is coupled to a passive heat
sink utilizing innovative heat pipe technology, and is
protected with a self resetting thermal protector.
20-3/4"
LED DRIVER:
Each string of 120 LEDs is powered by a single 40 watt,
constant current Thomas Research Products LED driver
(up for 4 drivers per fixture). The driver is UL8750 and
Class 2 compliant. Lutron Series A drivers also available
11-3/4"
DIMMING:
Standard 0-10v dimming provides flicker-free
dimming to 10%. For sizing of the circuit control,
the dimming circuit may require up to 1.2mA of sink
current. See list of compatible dimmers on page 4.
15-3/8"
Lutron 2-wire, 3-wire, and EcoSystem dimming
available to 1%.
Installation:
Universal adjustable mounting brackets accommodate
1.5” or ¾” lathing channel or ½” EMT (by others) or
Prescolite B24 or B6 bar hangers.
certificationS:
CSA certified to US and Canadian safety standards.
Suitable for damp locations, or wet locations with a
lens. ENERGY STAR® qualified. Product is marked
spacing and must be installed with the following
minimum spacings:
"A"** 12" 13-1/4"**
7-3/4"
9"
REFLECTOR*
25°
35°
45°
55°
Center to Center of adjacent luminaires : 36”
Minimum Overhead Clearance: 19”
(To bottom of metal pan)
HEIGHT (A)
18"
15"
11"
10"
*WITH LENS ASSEMBLY
**Dimension “A” may or may not be
limiting vertical dimension depending
upon chosen reflector.
Center of Luminaire to Side of Building Member : 18”
Warranty:
5 Year Warranty. See www.prescolite.com for details.
Order housing, reflector, and accessories separately
Catalog Number: MD8LED3L35K8-8MD3LMD25SLB24
Housing
OUTPUT
LED COLOR TEMP
CRI
VOLTAGE
OPTIONS
TRIM AperturE
❑27K ❑8 ❑Blank ❑Blank
❑8MD
❑MD8LED ❑3L2
3000
Standard
2700 80+ 120 thru
8" Alzak
8" High 277
CRI
Delivered
0-10V
Kelvin
Reflector
output
Volt
Lumens
dimming
❑30K
LED
2
3
❑6L
❑347
3000
❑HDM
housing
6000
347 Volt
Kelvin
Lutron
Delivered ❑35K
3-wire/
Lumens 3500
EcoSystem
2
❑9L
Kelvin
to 1%
9000
❑40K
❑2DM
Delivered 4000
Lutron 2-wire
Lumens
Kelvin
Leading
❑12L2
❑50K
Edge to 1%
12000 5000
(120v only)
Delivered
Kelvin
❑WIH
Lumens
WiHUBB
enabled
Must specify either WT or BT for painted cone
Housing and reflector output must be consistent
3
Available in standard 0-10V dimming only.
1
2
A Division of Hubbell Lighting, Inc.
output
❑3L2
Suitable
for 3000
Lumen
Housings
❑6L2
Suitable
for 6000
Lumen
Housings
❑9L2
Suitable
for 9000
Lumen
Housings
❑12L2
Suitable
for
12000
Lumen
Housings
Example: MD8LED12L35K8-8MD12LWFL45
BEAM ANgle
REFLECTOR FINISH
Reflector COLORS
❑MD25 ❑Blank ❑Blank
Specular
Nominal
Clear Alzak
25
❑SS
❑CG
Degree
SemiChampagne
Cutoff
Specular
Gold Alzak
❑FL35
❑MFC
❑BL
Nominal
American
Black Alzak
35
Matte
❑WE
Degree
Wheat Alzak
Cutoff
❑LW
❑WFL45
Light Wheat
Nominal
Alzak
45
❑PW
Degree
Pewter Alzak
Cutoff
❑BC1
❑XFL55
Painted Black
Nominal
Cone
55
❑WC1
Degree
Painted
Cutoff
White Cone
Reflector OPTIONS
In a continuing effort to offer the best product possible we reserve the right to change, without
notice, specifications or materials that in our opinion will not alter the function of the product.
Web: www.prescolite.com
•
Tech Support: (888) 777-4832
ACCESSORIES
❑B24
❑CL
Set of two(2) 24"
Clear
bar
Lens over
hangers for T-bar
LED's
ceilings
(wet
location) ❑B6
Set of two (2) bar
❑SL
hangers for ceiling
Solite
joist up to 24"
Softening
centers
Lens over
LED's
❑SCA8D_
(wet
Sloped ceiling
location)
adapter (see
❑WT
note on page 4)
Painted
White
Flange
❑BT
Painted
Black
Flange
ARCH-LED-013
TYPE B - 120/277V
PHOTOMETRIC DATA
DRIVER DATA
Architektur- 8" High Lumen MD8LED
MD8LED3L
MD8LED6L
MD8LED9L
MD8LED12L
Lumen Multiplier Table
Input Voltage
120-277V
120-277V 120-277V
120-277V
Input Frequency
50/60 Hz
50/60 Hz
50/60 Hz
50/60 Hz
Input Current
0.35 (120v) 0.70 (120v)
1.05 (120v)
1.40 (120v)
0.15 (277v)
0.30 (277v)
0.45 (277v)
0.61 (277v)
Input Power 42W
84W
126W
168W
Constant Current Output 1100mA
1100mA
1100mA
1100mA
Power Factor
≥0.90
≥0.90
≥0.90
≥0.90
THD
<25%
<20%
<20%
<20%
EMI Filtering
FCC 47CFR
FCC 47CFR
FCC 47CFR
FCC 47CFR
Photometrics for the MD8LED are published
below at a nominal 3500 Kelvin temperature.
This table may be used to approximate the lumen
values at different Kelvin temperatures. Power
consumption would stay the same.
5000 Kelvin
4000 Kelvin
3500 Kelvin
3000 Kelvin
2700 Kelvin
Solite Lens
OF 15,
4 Class APart 15, Class APart 15, Class APart 15, Class A
Part
Operating Temperature -20ºC to 40ºC
-20ºC to 40ºC
-20ºC to 40ºC
-20ºC to 40ºC
Dimming
0-10V
0-10V
0-10V
t
0-10V
1.14
1.03
1.00
1.00
0.91
0.87
Over-voltage, over-current, short-circuit protected
**347V:
t L D Utilizes
Driver step-down transformer with 7% power loss for all 347V models
*See application notes on page 1 for details
MD8LED12L35K8-8MD12LXFL55
LED Light Engine: 3500K, 80+ CRI
System Wattage: 168.2W
Fixture Delivered Lumens: 12789
Fixture Efficacy: 76.0
Spacing Criteria: 1.4
2050
60˚
4100
45˚
6150
0˚
15˚
30˚
8345
0-60
12545
3000
60˚
6000
45˚
9000
0˚
15˚
30˚
65.3
98.1
0-90
12789
100.0
0-180
12789
100.0
CANDELA DISTRIBUTION
DEG
CANDELA
0
5
15
25
35
45
55
65
75
85
90
6016
5998
5596
6011
5526
4057
1269
105
31
6
0
MD8LED12L35K8-8MD12LWFL45
LED Light Engine: 3500K, 80+ CRI
System Wattage: 167.8W
Fixture Delivered Lumens: 12240
Fixture Efficacy: 72.9
Spacing Criteria: 1.2
75˚
%FIXT
0-40
80%
70%
50%
30%
7401
7616
8276
7997
6025
1888
155
48
18
4
0
Test No. 6231
Tested at 25ºC Ambient in accordance to IESNA LM-79-2008
10%
20% Effective Floor Cavity Reflectance
% Wall Reflectance
30
10
50
30
112 109 105 103 109 106 104 101 102 100 98
104 98 93 89 102 96 92 88 93 89 86
70 50 30 10 70
98
90
97
87
95
84
95
87
94
84
92
82
3
97
82
78
74
80
76
73
90
89
80
82
73
77
68
95
88
50
87
79
30
10 50 30 10 50
81
77
73
67
85
80
77
71
75
67
75
70
66
73
68
10
65
5
84
73
66
60
82
72
65
60
70
64
59
68
63
59
67
62
58
6
78
67
59
53
76
66
58
53
64
58
53
62
57
52
61
56
52
7
73
61
53
48
71
60
53
48
59
52
47
57
51
47
56
51
47
8
68
56
48
43
66
55
48
43
54
47
43
53
47
43
52
46
42
9
10
63
60
51
48
44
40
39
36
62
58
51
47
44
40
39
35
50
46
43
40
39
35
49
45
43
39
39
35
48
44
42
39
38
MD8LED12L35K8 8MD12LXFL55
LUMENS
35
Test No. 6234
Luminance Data in Candela/m2
Angle in Vertical
Average - 0º
45°
87700
55°
8876
%FIXT
0-40
10452
0-60
12166
85.4
99.4
0-90
12240
100.0
65°
3731
0-180
12240
100.0
75°
85°
2284
1507
CANDELA DISTRIBUTION
CANDELA
3934
2261
1
2
4
ZONE
0
5
15
25
35
45
55
65
75
85
90
8161
75°
85°
% Effective Ceiling Cavity Reflectance
ZONAL LUMEN SUMMARY
DEG
65°
Zonal Cavity Method
COEFFICIENTS OF UTILIZATION
Test No. 6234
Tested at 25ºC Ambient in accordance to IESNA LM-79-2008
90˚
LUMENS
Room Cavity
Ratio
75˚
ZONE
Zonal Cavity Method
COEFFICIENTS OF UTILIZATION
Room Cavity
Ratio
90˚
Luminance Data in Candela/
Sq. Meter
Average - 0º
Angle in Vertical
45°
188452
55°
72670
ZONAL LUMEN SUMMARY
% Effective Ceiling Cavity Reflectance
80%
70%
50%
30%
10%
20% Effective Floor Cavity Reflectance
% Wall Reflectance
30
10
50
30
1
2
113 110 107 105 110 108 105 103 104 102 100 100 98
107 101 97 93 104 99 95 92 96 93 90 93 90
97
88
96
90
95
88
94
86
3
100 93
80
84
81
79
4
70 50 30 10 70
94
86
88
80
83
75
98
93
50
92
85
30
87
79
10 50 30 10 50
83
75
89
83
85
78
81
74
87
81
83
76
73
79
75
10
72
5
89
79
73
68
87
79
72
68
77
71
67
75
70
67
73
69
66
6
84
74
67
62
82
73
66
62
71
66
61
70
65
61
68
64
61
7
79
68
62
57
77
68
61
57
66
61
56
65
60
56
64
59
56
8
74
64
57
52
73
63
57
52
62
56
52
61
55
52
60
55
51
9
10
70
66
59
55
53
49
48
45
69
65
59
55
52
49
48
44
58
54
52
48
48
44
57
53
51
48
48
44
56
52
51
48
48
MD8LED12L35K8 8MD12LWFL45
Web: www.prescolite.com • Tech Support: (888) 777-4832
701 Millennium Boulevard • Greenville, SC 29607 U.S.A. • Phone (864) 678-1000
Copyright ©2014 Prescolite, Inc., a division of Hubbell Lighting, Inc. All Rights Reserved
Specifications subject to change without notice. • Printed in U.S.A. • LFR-LED-013 • 2/14/14
44
Test No. 6231
TYPE B - 120/277V
PHOTOMETRIC DATA
ct r
MD8LED12L35K8-8MD12LFL35
LED Light Engine: 3500K, 80+ CRI
System Wattage: 167.4W
Fixture Delivered Lumens: 11657
Fixture Efficacy: 69.6
Spacing Criteria: 1.0
ZONE
75˚
3500
60˚
7000
45˚
10500
15˚
Luminance Data in Candela/m2
Angle in Vertical
Average - 0º
45°
15375
55°
4524
ZONAL LUMEN SUMMARY
90˚
0˚
Architektur- 8" High Lumen MD8LED
ff manual chuc
LUMENS
0-40
11273
96.7
0-60
11682
100.2
0-90
11657
100.0
65°
2098
0-180
11657
100.0
75°
85°
1269
754
CANDELA DISTRIBUTION
DEG
CANDELA
0
5
15
25
35
45
55
65
75
85
90
9792
10086
10492
8868
5821
331
79
27
10
2
0
Zonal Cavity Method
COEFFICIENTS OF UTILIZATION
Room Cavity
Ratio
irst re
% Effective Ceiling Cavity Reflectance
80%
70%
50%
30%
10%
20% Effective Floor Cavity Reflectance
% Wall Reflectance
30
10
50
30
1
2
113 111 108 106 111 108 106 104 104 103 101 101 99
108 103 99 95 106 101 97 94 98 95 92 95 92
98
90
97
92
96
90
95
88
3
102 96
83
87
84
82
4
70 50 30 10 70
97
89
91
84
50
87 100 94
79
95
88
30
90
83
10 50 30 10 50
86
79
92
86
88
81
85
89
78
84
86
80
77
82
79
10
76
5
92
83
77
73
90
82
77
73
81
76
72
79
75
71
77
74
71
6
87
78
72
68
86
77
71
67
76
71
67
74
70
66
73
69
66
7
83
73
67
63
81
72
67
62
71
66
62
70
65
62
69
65
61
8
78
69
62
58
77
68
62
58
67
62
58
66
61
58
65
61
57
9
10
74
71
65
61
58
55
54
51
73
70
64
60
58
55
54
51
63
60
58
54
54
51
62
59
57
54
54
51
61
58
57
54
54
MD8LED12L35K8 8MD12LFL35
50
Test No. 6233
30˚
Test No. 6233
Tested at 25ºC Ambient in accordance to IESNA LM-79-2008
ZONE
75˚
5000
60˚
10000
45˚
0˚
15˚
LUMENS
%FIXT
0-40
6539
0-60
6602
99.8
0-90
6616
100.0
65°
699
0-180
6616
100.0
75°
85°
508
377
98.8
CANDELA DISTRIBUTION
DEG
CANDELA
0
5
15
25
35
45
55
65
75
85
90
13273
13813
12329
3491
201
54
20
9
4
1
0
Zonal Cavity Method
COEFFICIENTS OF UTILIZATION
Room Cavity
Ratio
90˚
15000
Luminance Data in Candela/m2
Angle in Vertical
Average - 0º
45°
2508
55°
1145
ZONAL LUMEN SUMMARY
MD8LED12L35K8-8MD12LMD25
LED Light Engine: 3500K, 80+ CRI
System Wattage: 167.4W
Fixture Delivered Lumens: 6616
Fixture Efficacy: 39.5
Spacing Criteria: 0.6
% Effective Ceiling Cavity Reflectance
80%
70%
50%
30%
10%
20% Effective Floor Cavity Reflectance
% Wall Reflectance
10
50
30
1
2
115 112 110 108 112 110 108 107 106 105 103 102 101 100
110 106 103 100 108 105 102 99 102 99 97 99 97 95
70 50 30 10 70
99
96
98
94
97
93
3
106 101 97
93
91
89
4
102 97
92
50
30
94 104 100 96
89 101 95
91
10 50 30 10 50
93
88
97
93
94
90
92
87
95
92
30
93
89
90
86
90
87
10
85
5
99
92
88
84
97
91
87
84
90
86
83
88
85
83
87
84
82
6
95
88
84
80
94
88
83
80
86
82
80
85
82
79
84
81
79
7
92
85
80
77
91
84
80
76
83
79
76
82
79
76
81
78
76
8
89
82
77
74
88
81
77
73
80
76
73
79
76
73
78
75
73
9
10
86
83
78
76
74
71
71
68
85
82
78
75
74
71
70
68
77
75
73
71
70
68
76
74
73
70
70
68
76
73
72
70
70
MD8LED12L35K8 8MD12LMD25
30˚
Test No. 6232
Tested at 25ºC Ambient in accordance to IESNA LM-79-2008
Web: www.prescolite.com • Tech Support: (888) 777-4832
701 Millennium Boulevard • Greenville, SC 29607 U.S.A. • Phone (864) 678-1000
Copyright ©2014 Prescolite, Inc., a division of Hubbell Lighting, Inc. All Rights Reserved
Specifications subject to change without notice. • Printed in U.S.A. • LFR-LED-013 • 2/14/14
67
Test No. 6232
TYPE B - 120/277V
PHOTOMETRIC DATA
Dimming compatibility table
*0-10V Only. See www.lutron.com for HDM & 2DM Compatibility
Control Manufacturer
Wallbox Dimmer
Douglas Lighting Controls
WPC 5721
Entertainment Technology
Tap Glide TG600FAM120 (120V)
Tap Glide Heatsink TGH1500fam120 (120V)
Oasis DA200OFAMU (120/277V)
Honeywell, Inc.
EL731A1019 and EL7315A1009
HUNT Dimming
Preset Slide: PS-010-IV-120V and PS-010-WH-120V
Preset Slide: PS-010-3W-IV-120V and PS-010-3W-WH-120V
Preset Slide: PS-010-IV-277V and PS-010-WH-277V
Preset Slide: PS-010-3W-IV-277V and PS-010-3W-WH-277V
Preset Slide, controls FD-010: PS-1FC-010-IV- and PS-IFC-010-32-WH-120/277V
Preset Slide, controls FD-010: PS-IFC-010-32-IV- and PS-IFC-010-3W-WH-120/277V
Remoted mounted unit: FD-010120V and FD-010-277V
Lehigh Electric Products Co.
Leviton Lighting Controls
Div.
Lutron Electronics Co., Inc.
PDM Electrical products
Starfield Controls
The Watt Stopper, Inc.
Power Booster Available
EL7305A1010
Solitaire
PBX
Leviton Centura Fluorescent Control System
IllumaTechTM IP7 Series
CN100
PE300
Visit www.lutron.com/advance for the latest control information and selection
WPC-5721
TR61 with DALI Interface port
RT03 DALInet Router
LS-4 used with LCD-101 and LCD-103
wiHUBB®
Fixture comes with a pre-installed In-Fixture Module (1 relay, 0-10V) compatible with the HBA wiHUBB system. Actual dimming requires the selection of
0-10V dimming ballast as well. Consult factory for compatibility with EM fixtures.
SCA8D_
When ordering a sloped ceiling adapter, specify the degree of slope in 5º increments, maximum of 35º. For a more precise degree or wet ceiling
applications, please contact factory. Sloped ceiling adapter and housing must be installed at the same time.
Web: www.prescolite.com • Tech Support: (888) 777-4832
701 Millennium Boulevard • Greenville, SC 29607 U.S.A. • Phone (864) 678-1000
Copyright ©2014 Prescolite, Inc., a division of Hubbell Lighting, Inc. All Rights Reserved
Specifications subject to change without notice. • Printed in U.S.A. • LFR-LED-013 • 2/14/14
TYPE
C em - 120/277V
Type:
Project Name:
8HF
D I M E N S I O N S
R E F L E C T O R
K I T
L E N S E D
8˝ Aperture
8611
Tempered Clear
Tempered Prismatic
8614
8616Fresnel
6 7/8˝
6 7/8˝
Reflector standard Clear “Alzak”.
Other options consult factory.
7 1/4˝
Splay/Lens Holder Finish Options
7 1/4
8 1/2˝
8 1/2˝
Specular Clear “Alzak”
SCL
SGC
Soft Glow Clear
Etch Clear
ECL
WHTWhite
Options
14 1/2˝
Polished Flange
PF
Ceiling Cut Out 7 7/8˝
14 7/8˝
L E N S E D
B A F F L E D
F E A T U R E S
8˝ Aperture
8˝ COMMER CI AL H O R I ZO N TAL FL UO R ESCENT
Electrogalvanized steel frame components with spring steel reflector
clips for fast assembly of reflector. Innovative, rigid bar hangers
incorporate formed cross sections, joist positioning tabs, integral nails,
auxiliary nailholes, T-Bar slots and holes for locking bars to T-Bar using
#8 self-tapping screws (supplied by others). Bars extend 14˝-24˝. Frame
will also accept Caddy Bar #517B for fast installation in drop-in ceilings,
bars extend 27˝.
8621
Tempered Clear
Tempered Prismatic
8624
8626Fresnel
Electronic ballast, Class P, 50/60 HZ-120-277, Programmed Start,
thermally protected, 98% Power Factor, 1.00 Ballast Factor, <10% THD,
Class A sound rated. Minimum starting temperature -18°C/0°F. UL Listed component.
BL
WH
Heavy gauge electrogalvanized steel junction box, prewired and
grounded with easy access from below. Listed for through branch circuit
wiring.
Aluminum socket housing with quick a­ ssembly hardware for fast
assembly. UL Listed socket and electrical connectors.
Heavy gauge spun aluminum low iridescent reflector with self trimming
white painted flange. Polished Flange available.
6 7/8˝
Reflector standard Clear “Alzak”.
Other options consult factory.
7 1/4˝
Baffled Finish Options
8 1/2˝
Black Baffle
White Baffle
T U R B O
L O U V E R
8˝ Aperture
Turbo Louver
8676
Finish Options
6 7/8˝
Specular Clear “Alzak”
Soft Glow Clear
Etch Clear
White Reflector
SCL
SGC
ECL
WHT
7 1/2˝
8 3/4˝
Options
Polished Flange
PF
Features
Manufactured and Listed to UL 1598, ETL and CSA standards.
Suitable for Damp Locations.
Wet location under covered ceiling.
ORDERING INFORMATION
Lamps and Wattage
Quad and Triple Tube
1x13
1x18 DTT
2x13
2x18 DTT
2x26 DTT
TRT 1 Lamp Only
1x18 TRT
1x26, 1x32, 1x42 TRT
EXAMPLE: 8HF113E1-2-8611-SCL
Housing
Ballast
Reflector
Finish
Options
8HF113
8HF118
8HF213
8HF218
8HF226
E1-2
E3
DL
DAX1
DAX2
DA7
8611
8614
8616
SCL
SGC
ECL
WHT
F
EM
PF
TR
DGSK
8HF118
8HF132
Baffled
8621
8624
8626
Baffle
BL
WH
Turbo Louver
8676
Ballast Options
Electronic 120-277 volt is standard
E1-2 -Electronic
(120-277V)
E3 -Electronic
(347V)
Dimming Ballast Options
DL - Lutron Eco System (120-277V)
DAX1 - Advance Mark X (120V)
DAX2 - Advance Mark X (277V)
DA7 - Advance Mark VII (120-277V)
Vantage reserves the right to change components, finishes or design details in any manner
which does not alter the installed appearance or reduce performance and intended function.
Options Descriptions
F - Fused
EM - Emergency Battery
PF - Polished Flange
TR - Tamper Resistant
DGSK - Silicone-Sealed Lens & Gasketing
s See Options pages for other options and finishes.
Vantage recommends the use of Philips or Sylvania lamps.
Rev 01/14
16
V A N T A G E
L I G H T I N G
I N C
V A N T A G E L T G . C O M
TYPE C - 120/277V
Project Name:
8HF
Type:
D I M E N S I O N S
R E F L E C T O R
K I T
L E N S E D
8˝ Aperture
8611
Tempered Clear
Tempered Prismatic
8614
8616Fresnel
6 7/8˝
6 7/8˝
Reflector standard Clear “Alzak”.
Other options consult factory.
7 1/4˝
Splay/Lens Holder Finish Options
7 1/4
8 1/2˝
8 1/2˝
Specular Clear “Alzak”
SCL
SGC
Soft Glow Clear
Etch Clear
ECL
WHTWhite
Options
14 1/2˝
Polished Flange
PF
Ceiling Cut Out 7 7/8˝
14 7/8˝
L E N S E D
B A F F L E D
F E A T U R E S
8˝ Aperture
8˝ COMMER CI AL H O R I ZO N TAL FL UO R ESCENT
Electrogalvanized steel frame components with spring steel reflector
clips for fast assembly of reflector. Innovative, rigid bar hangers
incorporate formed cross sections, joist positioning tabs, integral nails,
auxiliary nailholes, T-Bar slots and holes for locking bars to T-Bar using
#8 self-tapping screws (supplied by others). Bars extend 14˝-24˝. Frame
will also accept Caddy Bar #517B for fast installation in drop-in ceilings,
bars extend 27˝.
8621
Tempered Clear
Tempered Prismatic
8624
8626Fresnel
Electronic ballast, Class P, 50/60 HZ-120-277, Programmed Start,
thermally protected, 98% Power Factor, 1.00 Ballast Factor, <10% THD,
Class A sound rated. Minimum starting temperature -18°C/0°F. UL Listed component.
BL
WH
Heavy gauge electrogalvanized steel junction box, prewired and
grounded with easy access from below. Listed for through branch circuit
wiring.
Aluminum socket housing with quick a­ ssembly hardware for fast
assembly. UL Listed socket and electrical connectors.
Heavy gauge spun aluminum low iridescent reflector with self trimming
white painted flange. Polished Flange available.
6 7/8˝
Reflector standard Clear “Alzak”.
Other options consult factory.
7 1/4˝
Baffled Finish Options
8 1/2˝
Black Baffle
White Baffle
T U R B O
L O U V E R
8˝ Aperture
Turbo Louver
8676
Finish Options
6 7/8˝
Specular Clear “Alzak”
Soft Glow Clear
Etch Clear
White Reflector
SCL
SGC
ECL
WHT
7 1/2˝
8 3/4˝
Options
Polished Flange
PF
Features
Manufactured and Listed to UL 1598, ETL and CSA standards.
Suitable for Damp Locations.
Wet location under covered ceiling.
ORDERING INFORMATION
Lamps and Wattage
Quad and Triple Tube
1x13
1x18 DTT
2x13
2x18 DTT
2x26 DTT
TRT 1 Lamp Only
1x18 TRT
1x26, 1x32, 1x42 TRT
EXAMPLE: 8HF113E1-2-8611-SCL
Housing
Ballast
Reflector
Finish
Options
8HF113
8HF118
8HF213
8HF218
8HF226
E1-2
E3
DL
DAX1
DAX2
DA7
8611
8614
8616
SCL
SGC
ECL
WHT
F
EM
PF
TR
DGSK
8HF118
8HF132
Baffled
8621
8624
8626
Baffle
BL
WH
Turbo Louver
8676
Ballast Options
Electronic 120-277 volt is standard
E1-2 -Electronic
(120-277V)
E3 -Electronic
(347V)
Dimming Ballast Options
DL - Lutron Eco System (120-277V)
DAX1 - Advance Mark X (120V)
DAX2 - Advance Mark X (277V)
DA7 - Advance Mark VII (120-277V)
Vantage reserves the right to change components, finishes or design details in any manner
which does not alter the installed appearance or reduce performance and intended function.
Options Descriptions
F - Fused
EM - Emergency Battery
PF - Polished Flange
TR - Tamper Resistant
DGSK - Silicone-Sealed Lens & Gasketing
s See Options pages for other options and finishes.
Vantage recommends the use of Philips or Sylvania lamps.
Rev 01/14
16
V A N T A G E
L I G H T I N G
I N C
V A N T A G E L T G . C O M
TYPE D - 120/277V
PROJECT INFORMATION
ROUGH-HOUSE™
Job Name
Fixture Type
RHL7 SERIES
Catalog Number
PRODUCT FEATURES:
Approved by
»»Surface mount – ceiling or wall;
7"×24", 7"×36" or 7"×48"
»»18-gauge cold rolled steel housing
»»UV-Stabilized high impact acrylic lens
»»ADA Compliant
»»One year guarantee
SPECIFICATIONS:
HOUSING: 18-gauge CRS. TGIC polyester powder coat finished – 5-step pre-treatment.
REFLECTOR: Full reflector/wire cover – 92% reflectivity.
LENS: UV-stabilized, high impact pearlescent acrylic. Smooth exterior, linear prismatic interior. Nominal thickness .156". Lens locked in place with tamper-resistant stainless steel Torx® with center
pin fasteners.
END CAPS: High impact resistant, injection molded black or white polycarbonate.
HARDWARE: Stainless steel, tamper-resistant Torx fasteners.
ELECTRICAL: Class P ballasts. Fluorescent electronic 120/277/347 and dual voltage ballasts high power factor.
INSTALLATION: Standard four-point (24" and 36" housing) or six-point (48" housing) mounting required for One Year Guarantee. For surface conduit installation, end cap interior is provided with
drill points for field drilling.
LISTINGS: UL and CUL listed for Damp Location. ADA Compliant.
ADA
ORDERING INFORMATION (Ex: RHL7-48-MW-PIA-2-32-IS-1-347)
Model
RHL7
Length
24
Finish
Lens Type
MW
Lamp Qty
PP
2
Length
242'
363'
484'
Lens Type
PIA Pearlescent High Impact Acrylic
CP Clear Polycarbonate
PP Pearlescent Polycarbonate
Finish
MW Matte White
MB Matte Black
Lamp Quantity (Cross Section)
1One
2Two
Lamp Type
17
Ballast Type
Ballast Qty
IS
Voltage
1
Options
DV
EL* 500 Minimum Lumen Battery Pack
(90 Minutes; 32°F Starting Temperature)
FS Single Fuse & Holder
●
PEL* 1100 Minimum Lumen Battery Pack
(90 Minutes; 32°F Starting Temperature)
PH Phillips Head Lens Retention Screw
■
Ballast Type
IS
Instant Start Electronic <10% THD (T8)
RS Rapid Start Electronic <10% THD (T8,T5)
SB Specified Ballast
Ballast Quantity
1One
2Two
Lamp Type
2' Lengths
14F14T5
17F17T8
* Dry Location only (EL option). One lamp maximum in
emergency mode
■
2' and 3' fixtures available in one lamp cross section only;
have minimum 350-450 lumen battery pack
●
4' fixtures only
Voltage
120 120 Volts
277 277 Volts
347 347 Volts (T8 only)
DV 120-277 Volts
3' Lengths
21F21T5
25F25T8
Options
4' Lengths
28F28T5
32F32T8
DIMENSIONAL DATA
CROSS SECTION
MOUNTING HOLES
B
7.04"
C
0.312" Dia.
Mounting Holes
4.50"
2.87"
A
DIMENSIONAL DATA (IN INCHES)
A
B
4' – T8
4' – T5
3' – T8
3' – T5
2' – T8
2' – T5
48.8044.00
46.8442.00
36.8032.00
35.0330.00
24.8020.00
23.2218.00
C
22.00
21.00
n/a
n/a
n/a
n/a
www.kenall.com
P: 800-4-Kenall
F: 847-360-1781
1020 Lakeside Drive Gurnee, Illinois 60031
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers,
and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof.
Content of specification sheets is subject to change; please consult www.kenall.com for current product details. © 2013 Kenall Mfg. Co. All rights reserved.
RHL7-120313
TYPE E em - 120/277V
KL Bi-pin
Premium Industrial / 2, 3, or 4-Lamp T5, T5HO, T8
Project Information
Project Name
Type
Catalog No.
Date
Construction
Features
•
•
•
•
•
•
•
Available in 4' and 8' lengths
Apertured reflectors have 15% uplight
Spring loaded turret lampholders
6' lamp spacing
For individual or continuous row mounting
Channel ends double as joiners
Full depth end closures available
Heavy steel housing with longitudinal reinforcing
ribs for extra strength. Reflector die-embossed
with transverse ribs for maximum rigidity. Solid top
or 15% uplight versions with extruded openings
available.
Finish
White painted parts are treated with a five stage
phosphate bonding process and finished with
a high reflectance baked enamel. LSR and M4R
reflectors specular room side, Mill finish aluminum
top surface.
Ballasts
Energy efficient, thermally protected, automatic
resetting, Class P, high power factor, sound rated
Ordering Information
KL
4
Model
Size
KL Premium
Industrial
4 4'
8 8'
–
2
No. of Lamps in
cross section
2 Two
3 Three
4 Four
Accessories
(Order Separately)
KZT Zip Tee Hanger - 1½" spacer on
T-bar ceiling
KTH Slide Clamp Tong Hanger
S18 18" Stem, canopy and 8° aligner
SS18 18", 45° Swivel Stem & Canopy
KHC 24" Chain Hanging Assembly
KLEC Full Depth End Closure
KLWG4 Wire Guard 4' lg. - 2 required per
8' fixture
KLEGG White Straight Blade Egg Crate
Louver 4' - 2 required per 8' fixture
OS1K Occupancy Sensor Kit,
120/277/347V, One Relay1
A, unless otherwise specified. CEE NEMA Premium
compliant.
Electrical
Standard class “P”, thermally protected, autoresetting HPF ballast, sound rated A. CEE NEMA
Premium compliant. All ballast leads extend a
minimum of 6" through access location. NEC/CECcompliant ballast disconnect is standard.
Certification
All luminaires are built to UL 1598 standards and
bear appropriate UL and cUL or CSA labels. Damp
location labeling is standard. Emergency-equipped
fixtures labeled UL 924.
Example KL4-232-U-EU-GLR-PAF
17
–
E
–
U
U
Lamp Type
Reflector Type
Voltage
28 4', T5: 28 Watt
32 4', T8: 32, 30, 28 or
25 Watt
54 4', T5HO: 54 or 51
Watt
U Apertured Reflector for
Uplight
ST Solid Top (No Uplight)
M4RST Solid Top Reflector
with 95% Reflective
Specular Silver Finish
M4RU Apertured Reflector
with 95% Reflective
Silver Finish
U 120V-277V
347 347V
EL141ST
–
Options
GLR
GMF
El141
BC
Fast Blow Fuse
Slow Blow Fuse
Emergency Battery Pack (self test)
Branch Circuit Plug-on Wiring
System (See options section
for details.)
PAF Paint After Fabrication
NYC NYC Compliant
NYCU NYC Compliant, Union Label
Ballast
E Electronic T8, Instant Start
4E 4-Lamp Electronic T8, Instant Start
EP Electronic, Program Start
4EP 4-Lamp Electronic, Program Start
For others available, see Ballast Options.
Use programmed start ballast. Not recommended for use with instant start. For more occupancy/daylight harvesting sensor accessories see Technical section.
1
Page 1/2 Rev. 07/15/13
© 2013 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
Industrials / KL bi-pin
TYPE E em - 120/277V
KL Bi-pin
Premium Industrial / 2, 3, or 4-Lamp T5, T5HO, T8
Photometric Data
Zonal Lumen Summary
Zone
Luminaire Data
0-30
0-40
0-60
0-90
90-120
90-130
90-150
90-180
0-180
KL4-232-U
KL Industrial
1' × 4' 2-Lamp Industrial with
Apertured White Reflector
R2P32
0.95
FO32/41K
2900
74
N/A
0º = 1.27 90º = 1.30
Length: 4.00
Width: 1.02
Height: 0.00
Ballast
Ballast Factor
Lamp
Lumens per Lamp
Watts
Shielding Angle
Spacing Criterion
Luminous Opening
in Feet
1090
1807
3314
4396
179
263
518
817
5212
18.8
31.1
57.1
75.8
3.1
4.5
8.9
14.1
89.9
Energy Data
20.9
34.7
63.6
84.3
3.4
5.0
9.9
15.7
100.0
Indoor Candela Plot
RCR
70
94
85
77
71
65
60
55
51
48
45
80
50 30
90 86
78 71
68 60
60 52
53 45
48 39
43 35
39 31
36 28
33 26
10
82
66
54
46
39
34
30
26
23
21
70
90
81
74
67
62
57
53
49
46
43
70
50 30
86 83
75 69
65 58
58 50
51 44
46 38
42 34
38 31
35 28
32 25
10
79
64
53
45
38
33
29
26
23
21
50
80
69
60
53
48
43
39
35
33
30
50
30
77
64
55
47
41
36
32
29
26
24
10
74
61
50
42
36
32
28
25
22
20
89.9%
Luminaire Efficacy Rating (LER)
IESNA RP-1-1993 Compliance
Comparative Yearly Lighting
Energy Cost per 1000 Lumens
67
Non-Compliant
$3.58 based on
3000 hrs. and
$0.08 per KWH
AVG. LUMINANCE (Candela/Sq. M.)
Coefficients of Utilization (%)
RC
RW
1
2
3
4
5
6
7
8
9
10
Total Luminaire Efficiency
Average Luminance Angle
Luminaire
Test 10183 Test Date 1/8/03
Lumens % Lamp % Fixt.
0
0
62
51
42
36
31
27
24
21
19
17
0
30
40
45
50
55
60
65
70
75
80
85
0.0
22.5
45.0
67.5
90.0
3654
3616
3578
3544
3509
3459
3387
3296
3155
2956
2674
2149
3654
3622
3595
3582
3579
3569
3493
3477
3595
3374
3464
2967
3654
3671
3706
3712
3776
3923
3894
3652
3718
4210
3342
2876
3654
3726
3788
3921
4104
3905
3704
3839
4327
4353
2370
2785
3654
3717
3833
4000
4059
3827
3667
3964
4536
3955
2355
2815
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
Dimensional Data
Mounting Accessories
9813/16"
887/8"
2"
2"
11/8"
15/16"
431/32"
4913/32"
NOTE: Fixtures with T5/T5HO
lamping are 48" and
98" in length.
2"
497/16"
39½"
2"
15/16" 11/8"
39½"
431/32"
KHC
S18
43/16"
61/8"
35/8"
6"
133/8"
KZT
KTH
A: 7/8" Diameter knockout
B: .570" × .656" Strain Relief knockout
E: 11/8" Diameter knockout
NOTE: All dimensions are in inches; dimensions and specifications are subject to change without notice. Please consult factory or check sample for verification.
Page 2/2 Rev. 07/15/13
© 2013 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
Industrials / KL bi-pin
Electrical Options
TYPE E em - 120/277V
Emergency Battery Packs Installed
Technical
Luminaires with factory installed battery packs will bear the UL Emergency equipment label. Dry location labeling standard. Standard inverter
options below are not suitable for cold temperature starting, damp or wet location labeling. Optional inverters available for these applications.
Consult factory or specify vendor’s catalog number.
EL
EL61
EL71
EL72
350-450 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
500-600 lumens for one 2'-4' lamp (T8, T12, U-Bent, TT)
600-700 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
600-700 total lumens for two 2'-8' lamps (T8, T12, U-Bent)
EL141
EL142
EL5*
EL5H*
1100-1400 lumens for one 2'-8' lamp (T8, T12, U-Bent, TT)
1100-1400 total lumens for two 2'-4' lamps
390-700 lumens for one 2'-4' T5/T5HO
725-1250 lumens for one 2'-4' T5/T5HO
*These inverters not available in some 2' fixtures due to space constraints. Remote mounting using accessory enclosure (by others) recommended.
Fusing
Fusing is available on all fixtures to prevent over current from being transmitted upstream through the fixture as may be possible due to a dead
short fault in a ballast. Specify GLR (fast blow) or GMF (slow blow) fusing options. Fuses are not UL listed to break under load and therefore are
not a substitute for the in-fixture ballast disconnects supplied standard where required by the National Electric Code.
Fixture Flex and Leads
Fixture flex (also called pre-wire or whip) is a UL listed lighting component for recessed fixtures to provide the electrical wiring between the
junction box and recessed fixture. Flex may be no longer than 6'. Typical cables use ⅜" flexible conduit and three or four 18 gauge leads. Three
wires provides one line voltage hot lead. Add a wire for each separate hot lead required including separately switched ballasts, switch dim
ballast or battery pack to be powered through the flex cable. Flex cables are shipped pre-wired to the recessed fixture. Add option designation
to catalog number after ballast options. Eg. C388. Wire colors will be coded black/white/red/yellow plus a ground for line voltages. 588DIMM is
available with black/white violet, grey and ground for use with low voltage dimming leads.
Cable
No. of Wires
C Cable
Cable Diameter
3 3
4 4
5 5
8 ⅜"
2 ½"
Wire gauge
8 18 gauge
4 14 gauge
2 12 gauge
Miscellaneous Fixtures and Electrical Options (add As Suffix on end of Catalog string)
Fixture/Option
Cat. No.
PSW
PSWD
4PSW
Description
Pull switch, one circuit, 120V only
Pull switch, wired to the downlight circuit on a two circuit unit, 120V only
Four-way pull switch for two circuit, two lamp unit, 120V only
For Use With
Selected strips, surface units
and industrials. Contact factory
for applications
NL
Medium base lampholder for 15W, 25W, 40W, or 60W T10 lamp. Lamp not
included. 120V only
AWN, SM units
Fluorescent Night Light for 7W, T-4, G23 lamp
Fluorescent Night Light for 9W, T-4, G23 lamp
Fluorescent Night Light for 13W, T-4, GX23 lamp
Lamp not included. PL ballast will default to fixture voltage unless specified
Grounded convenience outlet (120V only)
4PS, SM, and WAL series
PL7
PL9
PL13
GCO
C6P15_ 6' Cord and Straight Blade, NEMA 5-15P, 15A (Add Voltage: 1 = 120)
C6TL15_ 6' Cord and Twist-Lock Plug, NEMA L5-15P (120V) NEMA L7-15P (277V), 15A
(Add Voltage: 1 = 120, 2 =277)
C6TL20_ 6' Cord and Twist-Lock Plug, NEMA L5-20P (120V) NEMA L7-20P (277V), 20A
(Add Voltage: 1 = 120, 2 =277)
F3C_
3-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
F4C_
4-Conductor feed cord, 18ga stranded wire
(Add length needed: 5 = 5', 10 = 10', or 15 = 15')
GLR
Fast blow fuse, fuse amps based on fixture ordered
112
WPM, WM, WAL, UCS and UC
Standard on SA, W
All industrial fixtures
All industrial fixtures
All fixtures
TYPE E - 120/277V
KL Bi-pin
Premium Industrial / 2, 3, or 4-Lamp T5, T5HO, T8
Project Information
Project Name
Type
Catalog No.
Date
Construction
Features
•
•
•
•
•
•
•
Available in 4' and 8' lengths
Apertured reflectors have 15% uplight
Spring loaded turret lampholders
6' lamp spacing
For individual or continuous row mounting
Channel ends double as joiners
Full depth end closures available
Heavy steel housing with longitudinal reinforcing
ribs for extra strength. Reflector die-embossed
with transverse ribs for maximum rigidity. Solid top
or 15% uplight versions with extruded openings
available.
Finish
White painted parts are treated with a five stage
phosphate bonding process and finished with
a high reflectance baked enamel. LSR and M4R
reflectors specular room side, Mill finish aluminum
top surface.
Ballasts
Energy efficient, thermally protected, automatic
resetting, Class P, high power factor, sound rated
Ordering Information
KL
4
Model
Size
KL Premium
Industrial
4 4'
8 8'
–
2
No. of Lamps in
cross section
2 Two
3 Three
4 Four
Accessories
(Order Separately)
KZT Zip Tee Hanger - 1½" spacer on
T-bar ceiling
KTH Slide Clamp Tong Hanger
S18 18" Stem, canopy and 8° aligner
SS18 18", 45° Swivel Stem & Canopy
KHC 24" Chain Hanging Assembly
KLEC Full Depth End Closure
KLWG4 Wire Guard 4' lg. - 2 required per
8' fixture
KLEGG White Straight Blade Egg Crate
Louver 4' - 2 required per 8' fixture
OS1K Occupancy Sensor Kit,
120/277/347V, One Relay1
A, unless otherwise specified. CEE NEMA Premium
compliant.
Electrical
Standard class “P”, thermally protected, autoresetting HPF ballast, sound rated A. CEE NEMA
Premium compliant. All ballast leads extend a
minimum of 6" through access location. NEC/CECcompliant ballast disconnect is standard.
Certification
All luminaires are built to UL 1598 standards and
bear appropriate UL and cUL or CSA labels. Damp
location labeling is standard. Emergency-equipped
fixtures labeled UL 924.
Example KL4-232-U-EU-GLR-PAF
17
–
E
–
U
U
Lamp Type
Reflector Type
Voltage
28 4', T5: 28 Watt
32 4', T8: 32, 30, 28 or
25 Watt
54 4', T5HO: 54 or 51
Watt
U Apertured Reflector for
Uplight
ST Solid Top (No Uplight)
M4RST Solid Top Reflector
with 95% Reflective
Specular Silver Finish
M4RU Apertured Reflector
with 95% Reflective
Silver Finish
U 120V-277V
347 347V
EL141ST
–
Options
GLR
GMF
EL
BC
Fast Blow Fuse
Slow Blow Fuse
Emergency Battery Pack
Branch Circuit Plug-on Wiring
System (See options section
for details.)
PAF Paint After Fabrication
NYC NYC Compliant
NYCU NYC Compliant, Union Label
Ballast
E Electronic T8, Instant Start
4E 4-Lamp Electronic T8, Instant Start
EP Electronic, Program Start
4EP 4-Lamp Electronic, Program Start
For others available, see Ballast Options.
Use programmed start ballast. Not recommended for use with instant start. For more occupancy/daylight harvesting sensor accessories see Technical section.
1
Page 1/2 Rev. 07/15/13
© 2013 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
Industrials / KL bi-pin
TYPE E - 120/277V
KL Bi-pin
Premium Industrial / 2, 3, or 4-Lamp T5, T5HO, T8
Photometric Data
Zonal Lumen Summary
Zone
Luminaire Data
0-30
0-40
0-60
0-90
90-120
90-130
90-150
90-180
0-180
KL4-232-U
KL Industrial
1' × 4' 2-Lamp Industrial with
Apertured White Reflector
R2P32
0.95
FO32/41K
2900
74
N/A
0º = 1.27 90º = 1.30
Length: 4.00
Width: 1.02
Height: 0.00
Ballast
Ballast Factor
Lamp
Lumens per Lamp
Watts
Shielding Angle
Spacing Criterion
Luminous Opening
in Feet
1090
1807
3314
4396
179
263
518
817
5212
18.8
31.1
57.1
75.8
3.1
4.5
8.9
14.1
89.9
Energy Data
20.9
34.7
63.6
84.3
3.4
5.0
9.9
15.7
100.0
Indoor Candela Plot
RCR
70
94
85
77
71
65
60
55
51
48
45
80
50 30
90 86
78 71
68 60
60 52
53 45
48 39
43 35
39 31
36 28
33 26
10
82
66
54
46
39
34
30
26
23
21
70
90
81
74
67
62
57
53
49
46
43
70
50 30
86 83
75 69
65 58
58 50
51 44
46 38
42 34
38 31
35 28
32 25
10
79
64
53
45
38
33
29
26
23
21
50
80
69
60
53
48
43
39
35
33
30
50
30
77
64
55
47
41
36
32
29
26
24
10
74
61
50
42
36
32
28
25
22
20
89.9%
Luminaire Efficacy Rating (LER)
IESNA RP-1-1993 Compliance
Comparative Yearly Lighting
Energy Cost per 1000 Lumens
67
Non-Compliant
$3.58 based on
3000 hrs. and
$0.08 per KWH
AVG. LUMINANCE (Candela/Sq. M.)
Coefficients of Utilization (%)
RC
RW
1
2
3
4
5
6
7
8
9
10
Total Luminaire Efficiency
Average Luminance Angle
Luminaire
Test 10183 Test Date 1/8/03
Lumens % Lamp % Fixt.
0
0
62
51
42
36
31
27
24
21
19
17
0
30
40
45
50
55
60
65
70
75
80
85
0.0
22.5
45.0
67.5
90.0
3654
3616
3578
3544
3509
3459
3387
3296
3155
2956
2674
2149
3654
3622
3595
3582
3579
3569
3493
3477
3595
3374
3464
2967
3654
3671
3706
3712
3776
3923
3894
3652
3718
4210
3342
2876
3654
3726
3788
3921
4104
3905
3704
3839
4327
4353
2370
2785
3654
3717
3833
4000
4059
3827
3667
3964
4536
3955
2355
2815
RCR = Room Cavity Ratio
RC = Effective Ceiling Cavity Reflectance RW = Wall Reflectance
Dimensional Data
Mounting Accessories
9813/16"
887/8"
2"
2"
11/8"
15/16"
431/32"
4913/32"
NOTE: Fixtures with T5/T5HO
lamping are 48" and
98" in length.
2"
497/16"
39½"
2"
15/16" 11/8"
39½"
431/32"
KHC
S18
43/16"
61/8"
35/8"
6"
133/8"
KZT
KTH
A: 7/8" Diameter knockout
B: .570" × .656" Strain Relief knockout
E: 11/8" Diameter knockout
NOTE: All dimensions are in inches; dimensions and specifications are subject to change without notice. Please consult factory or check sample for verification.
Page 2/2 Rev. 07/15/13
© 2013 Columbia Lighting, a division of Hubbell Lighting, Inc. Specifications subject to change without notice.
701 Millennium Blvd. Greenville, SC 29607 / Tel 864.678.1000 / Website www.columbialighting.com
Industrials / KL bi-pin
TYPE G LF - 120/24V
www.ilight-tech.com
Plexineon White 1X Series
PRODUCT SUMMARY
PRODUCT FEATURES
• Three Kelvin temperatures
• Energy efficient
• Long lifetime
• Stable and consistent color temperature
• Low voltage
• Easy to install
• Cool to the touch
• For use as exterior or interior accent
lighting, direct view or indirect view
applications, coves, signage & more
Color Temperatures (+/- 10%)
Power Supply
• 3500°K
• 4500°K
• 6500°K
•
•
•
•
Diffuser Color
Class 2 24 VDC, 100 Watts - must be supplied by iLight
Primary voltage: 120 or 120-277 depending on model
Secondary voltage: 24VDC 4.1 A Max
Maximum illumination length of a single LED power supply:
32 feet (9.75m)
• Light amber hue (when not illuminated)
Power Supply Tips
Lengths Available
• 2’, 4’, 6’, 8’ (610 mm, 1219 mm, 1830 mm,
2438 mm)
• 2’ (610mm) field cuttable pieces
• Illuminated outside corner pieces
• Factory custom lengths available to the
1
nearest 1/2” (13mm) +/- 0.25’’ (6mm)
• Factory convex or concave bends to minimum
1
inside radius of 5’’ (127mm)
1
• Factory “easy bends” to 3/16” (5mm) radius
2
• Gentle field bends to a 48”(1219mm) radius
• 20% maximum overage for breaker for primary current draw
• Do not plug multiple power supplies into one run of
Plexineon
• All iLight power supplies should be on an independent circuit
• Recommend surge protection upstream from power supply
• Verify correct voltage prior to wiring to non-switching
power supplies
Low Voltage Cable
Maximum distance of low voltage cable in any given run:
• 14 AWG: 40 feet (12.19m)
• 12 AWG: 60 feet (18.29m)
• 10 AWG: 100 feet (30.48m)
1. Drawing required for production
2. Field bending allowed only on fixtures without C-channel
ORDERING INFORMATION
CLASS
VOLTAGE
COLOR
HOUSING
LENGTH
CHANNEL
T
24
W35
S
CL 27'
NC
T = Trim
24 = 24V
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
00
2F = 2 Feet
00
SC = Stainless
4F = 4 Feet
Steel Channel
6F = 6 Feet
NC = No Channel
8F = 8 Feet
CL = Custom Length
TT = 2 Foot Cuttable
PC = Outside Corner
BE = Bend - Easy
BN = Bend - Convex
BV = Bend - Concave
W35 = White 1X S = Silver
3500°K
W45 = White 1X
4500°K
W65 = White 1X
6500°K
Specification sheets are subject to change
without notice. For the most recent version,
please refer to www.ilight-tech.com.
iLight Technologies
VERSION
•
T 312.876.8630
•
F 312.876.8631
•
MK-0110
www.ilight-tech.com
TYPE G LF - 120/24V
www.ilight-tech.com
Plexineon White 1X Series
MECHANICAL
TECHNICAL INFORMATION
Width & Height Housing
Mounting
•
•
•
•
• Stainless steel spring mounted clips
• Clips to be 2” (51mm) in from end of piece and no
more than 2’ (610mm) maximum between clips
0.55”(14mm)w x 1.35’’(34mm)h with C-channel
UV and impact resistant acrylic diffuser
UV resistant plastic channel
Stainless steel C-channel for mechanical
support
• Electronic (Advance) Power Supply is 2 lbs. (0.9kg)
• Outdoor Magnetic Hybrid Power Supply is 9 lbs.
(4 kg)
Minimum Piece Spacing
• Linear (end to end) = 3/8” (10mm)
• Parallel (edge to edge) = 1” (25mm)
*The minimum space for ventilation surrounding the
Plexineon product is 1.0”. This distance should be maintained
on the three sides, left and right of the product as well as in
front of product. Other configurations subject to specific
application testing.
ELECTRICAL
• Electronic (Advance) = 9.50’’ x 1.18” x 1.70”
(242mm X 30mm X 43mm)
• Outdoor Magnetic Hybrid= 11.25” x 3.25” x 3.36”
(286mm x 83mm X 85mm)
108 mA/foot at 24VDC (354 mA/meter)
2.59 watts/foot (8.50 watts/meter)
• 14 AWG, PVC/Nylon Type TC 600 Volt power and
control cable or equivalent
• FT-4 fire rating
• Class 2 wiring system
• Connectors: Molex Splashproof - JIS D0203 S2
Maximum Run Length
Electrical Tips
24 V DC
ENVIRONMENTAL
Power Supply Dimensions
DC Cable
Load Voltage
2
Power Supply Weight
Load Current
32 feet (9.75m) with an iLight approved power
supply
• Only use iLight approved power supplies
• Do not cut non-cuttable pieces
Operating Temperature Range
Certification
-25°C to 50°C (-13°F to 122°F)
• Plexineon is MetLabs listed. MetLabs is a
Nationally Recognized Testing Laboratory
(NRTL). Complies with UL 1598 and CSA
c22.2 No. 250 in Luminaire,Wet location listed.
• Power Supplies are RU listed. RU stands for
Recognized Components by Underwriters
Laboratory.
Storage Temperature Range
-25°C to 75°C (-13°F to 167°F)
iLight Technologies
MK-0110
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
•
T 312.876.8630
•
F 312.876.8631
•
www.ilight-tech.com
TYPE G LF - 120/24V
Plexineon White 1X Series
www.ilight-tech.com
MOUNTING CLIPS
PLEXINEON CROSS SECTIONS
PLEXINEON PROFILE
TECHNICAL INFORMATION
iLight Technologies
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
•
T 312.876.8630
•
F 312.876.8631
•
www.ilight-tech.com
MK-0110
3
TYPE G LF - 120/24V
Plexineon White 1X Series
www.ilight-tech.com
TECHNICAL INFORMATION
ELECTRONIC (ADVANCE)
POWER SUPPLY
Plexineon Power Supplies
MAGNETIC HYBRID
POWER SUPPLY
IN 3R ENCLOSURE
DRY
MAGNETIC HYBRID 3-OUTLET
POWER SUPPLY IN 3R ENCLOSURE
DRY
DAMP
4
iLight Technologies
MK-0110
DRY
DAMP
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
•
T 312.876.8630
•
F 312.876.8631
•
www.ilight-tech.com
TYPE G LF - 120/24V
Plexineon White 1X Series
www.ilight-tech.com
INSIDE CORNER
OUTSIDE CORNER
TECHNICAL INFORMATION
iLight Technologies
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
•
T 312.876.8630
•
F 312.876.8631
•
www.ilight-tech.com
MK-0110
5
TYPE G LF - 120/24V
Plexineon White 1X Series
www.ilight-tech.com
PLEXINEON FIELD BENDING1-3
TECHNICAL INFORMATION
PLEXINEON FACTORY BENDING
Note 1: Field bending shown in easy direction. Cannot field bend into convex or concave bends.
Note 2: Easy direction refers to bend axis parallel to light direction.
Note 3: Field bending allowed only on fixtures without C-channel.
Convex
Concave
Easy Bend2
6
iLight Technologies
MK-0110
• 118 South Clinton, Suite 370 •
Chicago, IL 60661
•
T 312.876.8630
•
F 312.876.8631
•
www.ilight-tech.com
(please confirm finish)
TYPE S1 ve - 120/277V
Cat.#
ARF2 LED
Type
Job
DECORATIVE FLOOD
Approvals
PRODUCT IMAGE(S)
SPECIFICATIONS
Intended Use:
Compact flood with a variety of NEMA distributions
for lighting applications such as safety/security,
accent, flag pole, columns, facade, area, or signs;
Operating temperature of -35˚C to 40˚C
Construction:
• Rugged die-cast aluminum housing with
powder coat finish
• High impact UV stabilized acrylic outer lens
protects LEDs and allows for cleaning and debris removal
• Vented housing isolates LED module from driver, maximizing product life and performance
• Visor and vandal lens available
LED:
• 20 high powered LEDs deliver up to 4,692 lumens
• 5100K CCT 67 CRI, 4200K 70 CRI,
3000K 80 CRI
• Driver RoHS compliant and IP66
• 0-10V dimming driver
• 20KA surge protector (over current device)
option available
Installation:
• Traditional ½” x 14 NPS threaded adjustable knuckle mounting
• Easy maintenance access to electrical
components with removal of 4 screws from back of fixture housing
Listings:
• IP65
Knuckle aiming detail
• Listed to UL1598 for use in wet locations
• DLC Qualified (4200K and 5100K models only); Consult DLC website for more details:
http://www.designlights.org/QPL
Warranty:
5 year limited warranty, for more information visit:
http://www.hubbelloutdoor.com/resources/warranty/
Optical/Electrical
• Variety of NEMA distributions - N (3x3), M (4x4), RM (5x4) and W (6x6) - for wide range of
lighting applications
• 120-277V operation, 50/60Hz, 52w, 700mA, 81 LPW
DIMENSIONS
B
C
A
A
B
C
Weight
6.68”9.63”4.53” 8.5 lbs.
169 mm 244 mm 115 mm
3.8 kg
SHIPPING INFORMATION
CERTIFICATIONS/LISTINGS
Catalog
Number
IP65
Carton Dimensions
G.W(kg)/
CTN
ARF2 (Single carton 1 pc.)
3.81
Length
Inch (cm)
Width
Inch (cm)
Height
Inch (cm)
11.81"
9.45"
7.48"
Carton dimensions for shipping purposes only
LED Product Partner
ORDERING INFORMATION
ARF2
K
FAMILY
ARF2 Arceos
Flood
Medium
MOUNTING
K
Knuckle
1 DLC qualification 4K and 5K models only
2 Custom colors available, contact factory
20L
4K
# LEDS
LED CCT
20L 20 LEDS
3K1 3000K
4K 4200K
5K 5100K
070
DRIVE
CURRENT
070 700mA
W
PS
U
BEAM
VOLTAGE
3x3
U 120V-277V
DB
Bronze
M
4x4
1 120V
BL
Black
RM 5x4
2 208V
WH
White
W
3 240V
GR
Gray
4 277V
PS
Platinum
FG
Forest Green
RD
Red
CC2
Custom
Color
6x6
CONTROL
OPTION
MOUNTING
N
OPTIONS
F
PC Photocontrol
(voltage
specified and
determined
by voltage
field)
Fusing, 120
or 277V only
(voltage
specified and
determined
by voltage
field)
SP 20KA/
KV Surge
Protector
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2014 SPAULDING LIGHTING, All Rights Reserved • For more information visit our website: www.spauldinglighting.com • Printed in USA
SPA14-SPEC 2/14
TYPE S1 ve - 120/277V
(please confirm finish)
ACCESSORIES/REPLACEMENT PARTS - Order Separately
Catalog Number
FML-SPC
FML-VISOR-XX1
93047961AC
93043808
20750110264
Description
Polycarbonate lens (Replaces existing acrylic outer frame)
Top/Bottom visor (Tap holes in lens frame for field installation)
Acrylic lens w/ gasket
25w, 120-277V Dimming driver
Knuckle mount Dark Bronze finish. Contact factory for additional finishes
Top or Bottom
Visor Mount
Detail
1 Specify finish color to match fixture, e.g. DB - Bronze.
FRAME & LENS
FML-SPC
FML-VISOR – 3/4 View
Front View
PERFORMANCE DATA
# OF
DRIVE SYSTEM
LEDS CURRENT WATTS
20
700mA
52w
DIST.
TYPE
N
M
RM
W
NEMA
3x3
4x4
5x4
6x6
FIELD ANGLE
H˚ X V˚
32 x 32
54 x 54
83 x 66
107 x 107
5K
4K
3K
(5100K nominal, 67 CRI)
(4200K nominal, 70 CRI)
(3000K nominal, 80 CRI)
MAX BEAM
MAX BEAM
MAX BEAM
LUMENS LPW1 CANDLEPOWER LUMENS LPW1 CANDLEPOWER LUMENS LPW1 CANDLEPOWER
4692
91.5
37,587
4231
87
35,025
3274
67
28,248
4600
89
13,625
4265
88
12,313
3274
67
9,411
3926
76
6,582
3636
75
5,921
2835
58
5,002
4486
87
2,978
4119
85
2,851
3234
66
2,306
1 - Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the
configurations shown. Actual performance may differ as a result of end-user environment and application.
PROJECTED LUMEN MAINTENANCE
LUMINAIRE AMBIENT TEMPERATURE FACTOR (LATF)
OPERATING HOURS
1TM-21-11
AMBIENT
TEMP.
0 25,000 50,000
60,000
100,000
25°C / 77°F 1.00 0.98
0.96
0.96
0.94
40°C / 104°F 0.99
0.96
0.95
0.94
AMBIENT TEMPERATURE
0°C
32°F
10°C
50°F
68°F
20°C
25°C
77°F
30°C
86°F
40°C
104°F
50°C
122°F
Calculated L70
(HOURS)
>696,000
0.92
>565,000
ELECTRICAL DATA
NUMBER OF DRIVE CURRENT INPUT VOLTAGE CURRENT
DRIVERS
(mA)
(V)
(Amps)
120
0.56
2
700mA
277
0.26
# OF LEDS
20
SYSTEM POWER
(W)
50
50
LUMEN MULTIPLIER
1.02
1.01
1.00
1.00
1.00
0.99
0.98
Use these factors to determine relative lumen output for average ambient
temperatures from 0-50°C (32-122°F).
PHOTOMETRICS For additional photometric information and IES downloads, visit our web site at www.spauldinglighting.com
30'
15'
20'
15'
30'
10'
10'
20'
5'
5'
10'
10'
fc
10
10'
2fc
1fc
.5fc
30'
20'
10'
10'
10'
20'
5'
15'
3x3 Narrow
fc
20 fc
10
5fc
15'
10'
10'
20'
2fc
1fc fc
.5
1fc
.5fc
30'
20'
5'
5'
15'
20fc
10fc
5fc
2fc
10'
fc
50
10'
5'
30'
6x6 Wide
5'
.5fc
15'
10'
15'
100fc
fc
50 fc
20 c
f
10 c
5f
2fc
1fc
5'
5fc
20'
15'
10'
10'
10'
15'
4x4 Medium
15'
5 x 4 Rectangular Medium
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2014 SPAULDING LIGHTING, All Rights Reserved • For more information visit our website: www.spauldinglighting.com • Printed in USA
SPA14-SPEC 2/14
20'
30'
E
TYPE S1 - 120/277V
Lightscoop Ceiling washlights
(please confirm finish)
with mounting plate and LED
13 3/8"
18 1/8"
13 3/8"
464mm
340mm
155mm
6 1/8"
d240mm
9 1/2"
340mm
LED
Nä ö ü
Dry Damp Wet
ÖOutdoor
33237.023 Graphit m
LED 48W 6000lm 4000K neutral white
Version 2
Spherolit lens, wide beam
Product description
Housing: corrosion-resistant, cast aluminum, No-rinse surface treatment.
Double powder-coated. Optimized
surface for reduced accumulation of
dirt. Luminaire rotatable throught 240°.
Mounting plate: corrosion-resistant
aluminum.
Electronic control gear 120V/277V,
60Hz. 2 cable entries. Through-wiring
possible. 3-pole terminal block.
LED module: high-power LEDs on
metal-core PCB. SDCM<2. CRI>80.
L80/B10 50000h. Collimating lens made
of optical polymer.
Screw-mounted cover frame with
safety glass: corrosion-resistant cast
aluminum, double powder-coated.
Suitable for wet location (IP65): dustproof and water jet-proof.
Weight 20.50lbs / 9.30kg
Maximum wind load area 1.40ft2
ERCO Lighting Inc.
160 Raritan Center Parkway
Suite 10
Edison, NJ 08837
USA
Tel.: +1 732 225 8856
Fax: +1 732 225 8857
info.us@erco.com
135°
3000 cd
105°
C0-C180
C90 -C270
h=4ft
MF=1.00
ft
12
0.1
2
6
0.5
20
0
10
ft 24
18
12
6
6
Technical region: 120V/277V, 60Hz
We reserve the right to make technical
and design changes.
Edition: 04.03.2014
Current version under
www.erco.com/33237.023
1/2
E
TYPE S1 - 120/277V
Lightscoop Ceiling washlights
(please confirm finish)
Accessories
34991.000
Spacer
for surface-mounted cables.
Corrosion-resistant cast aluminum,
No-Rinse surface treatment. Graphit m,
double powder-coated.
Weight 0.51lbs / 0.23kg
33974.000
Ground socket
Metal, hot-dip galvanised.
Cable entry.
Weight 5.07lbs / 2.30kg
4 1/2"
666666
36664
153 mm
6"
4666663
600 mm
23 5/8"
4666666663
∅ 115 mm
13/16"
2 3/8"
6666364
20 mm
666663664
∅ 60 mm
200 mm
7 7/8"
46666
3
33981.000
Concrete anchor
Mounting plate with threaded bar and
fixing nuts M10. Individual parts to be
assembled on-site.
Weight 1.68lbs / 0.76kg
4 7/8"
366664
∅ 124 mm
Lightscoop Ceiling washlights
33237.023
2/2
TYPE S2 ve pole
(please confirm finish)
International
Round Straight Steel Light Poles
POLE SHAFT:
Fabricated from hot rolled welded steel tubing with minimum
yield strength of 42,000 PSI.
ANCHOR BASE:
Structural quality ASTM A-36. The base is provided with bolt
slots to accommodate a 7" – 9" bolt circle.
ANCHOR BOLTS:
Carbon steel conforming to AASHTO M314 grade-55 or ASTM
F1554 grade-55. Bolts are "L" shaped and are galvanized a
minimum of 12" on the threaded end. Each pole includes four
bolts each with two nuts and two flat washers.
FULL BASE COVER (optional):
Two piece cover fabricated from ABS plastic.
MOUNTING
HEIGHT
HANDHOLE:
Covered 2 1/2" x 5" reinforced handhole. A nut holder is provided near the handhole and includes a 1/2"-13 UNC hex
head bolt and nut.
HARDWARE:
All structural fasteners are galvanized high strength carbon
steel. All other fasteners are galvanized or zinc plated or stainless steel.
REINFORCED
HANDHOLE
W/COVER
AND
GROUNDING
STANDARD FINISH:
Galvanized or powder coated. Consult factory for standard or
custom colors.
MOUNTINGS OPTIONS:
Tenons- standard 2 3/8" x 4" or 4" x 6" or removable pole cap
used in conjunction with side mounted fixtures.
4 - ANCHOR
BOLTS WITH
THREADED END
GALVANIZED 12”
MIN. EACH BOLT
FURNISHED
WITH 2 HEX
NUTS AND 2
FLATWASHERS
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
Serving our customers and
the industry with quality
products since 1973.
www.nafcointernational.com
8.5
(please confirm finish)
TYPE S2 ve pole
Round Straight Steel Light Poles
POLE
CATALOG
NUMBER
RSS10-303C
NOMINAL
MOUNTING
HEIGHT (ft)
10
Max EPA AT: (Allows for 1.3 Gust Factor)
POLE
O.D.
INCHES
WALL
THICKNESS
INCHES
80
MPH
90
MPH
100
MPH
3.0
120
10.0
7.7
6.0
RSS10-404C
10
4.0
.120
19.1
15.0
12.2
RSS10-4545C
10
4.5
.120
24.5
19.5
15.8
RSS12-303C
12
3.0
.120
7.7
5.8
4.4
RSS12-404C
12
4.0
.120
15.0
11.8
9.5
RSS12-4545C
12
4.5
.120
19.8
15.7
12.7
RSS14-303C
14
3.0
.120
6.0
4.4
3.3
RSS14-404C
14
4.0
.120
12.2
9.4
7.6
RSS14-4545C
14
4.5
.120
16.2
12.8
10.3
RSS16-303C
16
3.0
.120
4.6
3.2
2.3
RSS16-404C
16
4.0
.120
9.6
7.4
5.9
RSS16-4545C
16
4.5
.120
13.1
10.2
8.2
RSS18-303C
18
3.0
.120
3.4
2.3
1.4
RSS18-404C
18
4.0
.120
7.6
5.7
4.5
RSS18-4545C
18
4.5
.120
10.5
8.2
6.5
RSS20-303C
20
3.0
.120
2.4
1.4
-
RSS20-404C
20
4.0
.120
6.0
4.4
3.4
RSS20-4545C
20
4.5
.120
8.5
6.6
5.2
RSS20-505C
20
5.0
.120
11.7
9.1
7.2
RSS25-404C
25
4.0
.120
2.8
1.9
1.3
RSS25-4545C
25
4.5
.120
4.8
3.6
2.7
RSS25-505C
25
5.0
.120
7.2
5.5
4.2
RSS25-505D
25
5.0
.180
12.1
9.4
7.4
RSS30-4545C
30
4.5
.120
2.3
1.5
1.0
RSS30-505C
30
5.0
.120
4.2
3.0
2.2
RSS30-505D
30
5.0
.180
8.0
6.5
4.7
1. All designs utilize .75" x 17" x 3" anchor bolts.
2. Pole base plate dimensions are the same for all
designs. See pole base detail drawing for dimensions.
3. Wind load includes 1.3 gust factor.
Variations in mounting heights listed are available.
POLE BASE AND HANDHOLE DETAIL
Dimensions and Specifications subject to change without notice.
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
www.nafcointernational.com
8.6
(please confirm finish)
CIMARRON
LED CL1S
TYPE S2 ve - 120/277V
Cat.#
Approvals
Type
Job
4.000
SPECIFICATIONS
Construction:
•Stylish vertically finned die-cast solid top
housing for maximum heat dissipation;
Stops collection of unsightly debris
•Rugged lower die-cast aluminum heat sink accelerates thermal management
and optimizes PCB and optical performance
• One piece die-cut silicone gasket with mechani-
cally compressed stainless steel bezel ensures weather proof seal around each individual LED for IP65 rating
•Backlight Control (BC) option available for 85%
spill light reduction, doesn’t change fixture
appearance or EPA, recommended for Type III and Type IV distributions
• Complements the Cimarron LED CL1 in the Hubbell Southwest series of outdoor fixtures
•Weight - 19 pounds, EPA - .45 ft2
• Features exclusive wiHUBB technology
-Wireless system for On/Off and 0-10VDC dimming protocol with functional range of
10-100%
-Programmable autonomous operation
Optics:
• Choice of 54 high brightness LED configurations with individual acrylic lenses specially designed for IES Type II, III, IV and V distributions
• 3000K, 80 CRI; 4200K, 70 CRI; 5100K, 67 CRI
Electrical:
• Universal input voltage 120-277 VAC, 50/60 Hz
•Ambient operating temperature -30˚ C to 40˚ C
•Automatic thermal self-protection
•Drivers have greater than 90% power factor and less than 10% THD
•Optional 0-10VDC continuous dimming to 10%
4.500
• LED drivers have output power over-voltage, over-current protection and short circuit
protection with auto recovery
• LED electrical assembly, including PR devices, consumes no power in the ‘off’ state
• Surge protection of 10KA 8/20 µSec wave; clamping voltage of 320V & surge rating of 273J
2014
3.000
16.312
48 LED 3/4 VIEW
3.000
12.000
32 LED
48 LED
DIMENSIONS
A
D
A
VOLTAGE
CL1S Cimarron LED
16L 16 High brightness LEDs
32L 32 High brightness LEDs
48L 48 High brightness LEDs
U Universal 120V-277V,
3
50/60 Hz
11
21
31
41
5
F
E4
120V
208V
C
C
D
G
E
B
C
D
E
F
G
12"
305mm
16.312"
414mm
4"
102mm
4.5"
114mm
3"
76mm
20.312"
515mm
4.13"
105mm
5W
3K 3000K, 80 CRI
4K 4200K, 70 CRI
5K 5100K, 67 CRI
PS
Leave blank for
700mA (standard)
2 Type II
3 Type III
Type IV
Type V Medium
Type V Short
Type V Wide
Type II rotated left
Type III rotated left
OPTIONS
BC
CD2,7 Continuous dimming
F(X)3,4 Fusing (replace X with voltage:
5
Backlight control
1-120V, 2-208V, 3-240V,
4-277V, 5-480V, 6-347V)
White
RPA3
RPA4
TB
WB
WHB6
Gray
WIH2,8 In-fixture wireless control module
Platinum Silver
PR(X)2 NEMA Photo cell receptacle
COLOR
DISTRIBUTION
H
5.625"
143mm
RPA4
DRIVE CURRENT
480V, 60 Hz
4
5M
5S
5W
2L
3L
4L
2R
3R
4R
E
A
CCT
347V, 60 Hz
G
H
277V
Notes: 1 - Select only when using voltage specific options F, WIH
2 - WIH cannot be combined with CD or PR(X)
3 - Fuse option not available with U voltage
4 - Select F3 fusing option for 220V
5 - Not recommended for Type 5S, 5M or 5W
6 - Order to match larger Cimarron CL1 with white bezels
7 - Dimming leads accessible for connection to third party dimming systems
8 - Only available with 120V or 277V input
9 - 0-10V fully adjustable dimming with automatic daylight calibration and different time delay settings, must order minimum of one remote control to program dimming settings, consult factory for details
B
Weight
240V
220V, 50 Hz
B
E
F
• IES Progress Award Winner - 2013
NO. OF LEDS
3.000
4.500
ORDERING INFORMATION ORDERING EXAMPLE: CL1S-A-48LU-5K-3-DB-RPA3
CL1S
A
32L
U
4K
complete with quick-mount plate
16 LED
16.312
4.000
Listings:
• Listed to UL1598 and CSA C22.2#250.0-24 for wet locations
•DesignLights Consortium (DLC) qualified
• IDA approved
• IP66
LED Product Partner
A 4” straight arm attached to housing
5.625
Warranty:
Five year limited warranty, for more information
visit: http://www.hubbelloutdoor.com/resources/
warranty/
SERIES
4.130
5.625
19 lbs.
8.62 kgs.
MOUNTING
12.000
4.130
CERTIFICATIONS/LISTINGS
Pedestrian
Scale
12.000
20.312
Installation:
• Quick-mount plate included for easy installation
• The decorative integral arm houses two stage hinge mechanism •Safety latch holds luminaire door to prevent “free swing”
• Quick-connect wiring for simplified, hassle-free
installation
• Suitable for applications requiring 3G testing prescribed by ANSI @136.31
Finish:
• TGIC thermoset polyester powder paint finish applied at nominal 2.5 mil thickness 16.312
PRODUCT IMAGE(S)
DB
BL
WH
GR
PS
RD
Dark Bronze
Black
Red
(premium color)
FG Forest Green
(premium color)
CC Custom Color
Type IV rotated left
Type II rotated right
Type III rotated right
3” Round pole adapter
4” Round pole adapter
Terminal block
Wall bracket
White LED bezel
(replace X with voltage:
U=120-277, 5=480, 6 =347)
MOTION CONTROL OPTIONS
SC09 Motion sensor On/Off control,
No light output when no motion detected
SCP9 Programmable motion control,
factory default is 50%
Type IV rotated right
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2014 SPAULDING LIGHTING, All Rights Reserved • For more information visit our website: www.spauldinglighting.com • Printed in USA
CL1SLED-SPEC 3/14
(please confirm finish)
PERFORMANCE DATA
NUMBER OF
LEDS
5K
(5100K NOMINAL, 67 CRI)
DRIVE
CURRENT
(MILLIAMPS)
16
32
TYPE S2 ve - 120/277V
SYSTEM
WATTS
38w
700mA
76w
48
110w
DISTRIBUTION
TYPE
2
3
4
5S
5M
5W
2
3
4
5S
5M
5W
2
3
4
5S
5M
5W
LUMENS
3053
3075
3113
3457
3731
3166
6527
6574
6654
7391
7327
6704
9864
9935
10056
11169
11073
10132
LPW*
80
81
82
91
98
83
86
86
88
97
96
88
87
90
92
101
101
92
4K
(4200K NOMINAL, 70 CRI)
B
U
G
2
0
0
3
0
1
2
2
2
3
3
4
2
1
1
0
1
1
2
2
2
0
2
2
LUMENS
3077
3099
3136
3484
3454
3160
6042
6085
6159
6841
6782
6206
9131
9593
9309
10339
10250
9379
LPW*
81
82
83
92
91
83
79
80
81
90
89
82
87
90
85
94
91
85
B
U
3K
(3000K NOMINAL, 80 CRI)
G
2
0
2
3
0
2
LUMENS
2438
2456
2486
2761
2737
2725
4788
4823
4881
5422
5375
4918
7236
7288
7377
8193
8123
9662
LPW*
64
65
65
73
72
72
63
63
64
71
71
84
66
66
67
74
74
85
B
U
G
2
0
1
3
4
1
0
1
2
Lumen values are from photometric tests performed in accordance with IESNA LM-79-08. Data is considered to be representative of the configurations shown. Actual
performance may differ as a result of end-user environment, application and inherent performance tolerances of the electrical components.
PROJECTED LUMEN MAINTENANCE
LUMINAIRE AMBIENT TEMPERATURE FACTOR (LATF)
AMBIENT TEMP.
0
25,000
50,000
25°C / 77°F
40°C / 104°F
1.00
0.98
0.98
0.96
0.96
0.95
*TM-21-11
60,000
0.96
0.94
100,000
0.94
0.92
CALCULATED
L70 (hours)
>675,000
>556,000
* Nichia 219B, 700mA, 85°C Ts, 10,000hrs
ELECTRICAL DATA
NUMBER OF
LED’s
16
32
48
NUMBER
INPUT
Drive Current
OF
VOLTAGE
[milliamps]
DRIVERS
(VOLTS)
120
277
1
347
480
120
277
std.
2
(700mA)
347
480
120
277
3
347
480
OPER.
CURRENT
[AMPS]
0.32
0.15
37.8
37.5
0.63
0.29
75.5
74.8
0.95
0.44
110.5
110.9
ACCESSORIES
PHOTOCONTROL EQUIPMENT
CATALOG NUMBER
PTL-1
PTL-8
PTL-5
PTL-6
PSC
SYSTEM POWER
IN-RUSH
[WATTS]
CURRENT (AMPS)
DESCRIPTION
Photocontrol - twist-lock cell (120V)
Photocontrol - twist-lock cell (120-277V)
Photocontrol - twist-lock cell (480V)
Photocontrol - twist-lock cell (347V)
Shorting cap - twist-lock
0°C
10°C
20°C
25°C
30°C
40°C
50°C
AMBIENT DATA
TEMP
LUMEN MULT.
32°F
1.02
50°F
1.01
68°F
1.00
77°F
1.00
86°F
1.00
104°F
0.98
122°F
0.98
MOUNTING ACCESSORIES
CATALOG NUMBER
CL1S-RPA3-XX1
CL1S-RPA4-XX1
WB-CR-XX
DESCRIPTION
Round pole adapter for straight arm (31⁄4 - 33⁄4”)
Round pole adapter for straight arm (37⁄8 - 41⁄ 2”)
Wall bracket
1 Replace XX with color choice, eg.: DB for Dark Bronze
TENON TOP POLE BRACKET ACCESSORIES
(2 3/8” OD tenon, RSS version requires 4” round pole adapter)
Catalog Number
SETA-XX1
RETA-XX1
TETA-XX1
Description
Square pole tenon adapter (4 at 90 degrees)
Round pole tenon adapter (4 at 90 degrees)
Triangular pole tenon adapter (3 at 120 degrees)
1 Replace XX with color choice, eg.: DB for Dark Bronze
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2014 SPAULDING LIGHTING, All Rights Reserved • For more information visit our website: www.spauldinglighting.com • Printed in USA
CL1SLED-SPEC 3/14
#2 DRILL PATTERN F
(please confirm finish)
TYPE S2 ve - 120/277V
FIXTURE MOUNTING
POLE COVER
FIXTURE
CAST ARM
FIXTURE
POLE TOP
POLE COVER
POLE COVER
POLE COVER
MOUNTING
CASTBOLTS
ARM
MOUNTING
BOLTS
2.25
NUT PLATE
NUT PLATE
CAST
ADAPTER
CAST
ADAPTER
NUT PLATE
NUT PLATE
SET SCREW
SQUARE POLE
3.5
Ø .875
Ø .875
HOLE
HOLE
QUICK-MOUNT
SQUARE POLE
PLATE
QUICK-MOUNT
2.25
.875
.875.875
ROUND
POLE
ROUND POLE
SET SCREW
.579
POLE TOP
3.5
3.5
Ø .563
2 HOLESØ .563
2 HOLES
#2 DRILL PATTERN FOR POLES
PLATE
4.962
4.962
2.625
#2 DRILL PATTERN FOR POLES
QUICK-MOUNT PLATE
.579
FIXTURE MOUNTING – FACTORY ROTATED OPTICS
For proper light distribution.875
and performance, rotated
.579
optics must be mounted as referenced in illustration.
Consult instruction sheet included when mounting.
.875
3.5
2L Type II rotated 90˚ left
3L Type III rotated 90˚ left
4L Type IV rotated 90˚ left
2R
3R
4R
Type II rotated 90˚ right
Type III rotated 90˚ right
Type IV rotated 90˚ right
4.962
4.962
3.5
4.962
4.962
QUICK MOUNT INSTALLATION
1
2.625
The Cimarron CL1S installation features:
1
2
QUICK-MOUNT PLATE
1 Quick-mount plate attaches to pole with two 3/4” bolts
2 4 - slot hex 1/4” captured screws secure luminaire door to top
2.625
3 Safety-latch holds luminaire door to prevent “free swing” door
QUICK-MOUNT
PLATE
4 Two stage hinge mechanism built into integral
arm
5 Quick-connect wiring for a simplified, hassle-free installation
For installation video
scan this code or
visit link below:
3
4
5
http://www.youtube.com/user/hubbelloutdoorbrands
LIGHTING FACTS
Spaulding Lighting • 701 Millennium Boulevard • Greenville, SC 29607 • Phone: 864-678-1000
Due to our continued efforts to improve our products, product specifications are subject to change without notice.
© 2014 SPAULDING LIGHTING, All Rights Reserved • For more information visit our website: www.spauldinglighting.com • Printed in USA
CL1SLED-SPEC 3/14
(please select finish)
CANTO G 450 LED
TYPE S2 - 120/277V
Specification
The smoothly engineered shape of the CANTO combined with
its gracefully arching pole creates a unique appearance. The
gentle curvature allows the pole to spatially define paths
or roadways. Two luminaire sizes and three pole heights
are available to meet proportional requirements of large or
small scale applications. The heavy cast aluminum housing
is fitted with a flat tempered glass lens with a quarter-turn
fastener for easy relamping. Hinged reflector assembly allows
access to the ballast tray. Mounting bracket and steel pole
with flush handhole are hot-dip galvanized prior to being
finished in high quality, finely textured paint. Base cover is
spun aluminum. All hardware is stainless steel. Standard
colors; matte silver grey metallic or graphite grey. Special
colors available.
Color
Model LED Module Temperature
2LV - 2 LEVO
CC450GModules
WW -3000K
3LV - 3 LEVO
Modules
NW - 4000K
Distribution
ME - Type III
Volt
Mounting Pole
Finish
UNV A - Single 17RC - 17'
SG - Silver
120-277V Mount
Round Curved Grey
GG Graphite
Grey
S - Type II
DIM - 0-10vDC Dimming
CC - Custom
Color
N - None
CW - 5600K
Ordering Information
CC450G
Option
0DEG - 0 degree tilt for full
cutoff classification
UNV
A
17RC
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > CANTO G
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/CANTO_G/
Page 1
(please select finish)
CANTO G 450 LED
TYPE S2 - 120/277V
Specification
HOUSING
One-piece domed housing is heavy cast aluminum. Hinged frameless tempered glass lens opens with single quarter-turn
fastener for easy relamping. Lens is sealed to the housing with one-piece closed cell silicone gasketing. Hinged reflector plate,
painted with high reflectance white paint, swings down allowing access to ballast components. Housing is fitted with stainless
steel weather-tight strain relief bushing for the power cable exiting the rear of the housing. Luminaire installs onto bracket
mounting plate with four socket head cap screws. All hardware is stainless steel.
OPTICS
Optics may be specified with 2 or 3 individual LED modules. Each module consists of a field replaceable aluminum core PCB
with fourteen high-power LEDs and a single piece prismatic lens molded from optical quality acrylic. The prismatic lens
redirects light output from the individual LEDs and is available in two distributions as a Type II Full Cutoff distribution (S optics)
or Type III Full Cutoff distribution (ME optics) when selecting the zero degree tilt option (0DEG) . Luminaire is suitable for use in
all LEED lighting zones. Available color temperatures are 3000K, 4000K, or 5600K.
ELECTRICAL
Electronic LED driver supplies 500mA drive current to LED modules with input voltage range from 120v to 277v at 50/60Hz.
LED DELIVERED LUMEN OUTPUT / POWER CONSUMPTION
2 Modules: 46 watts
3000K - Type II = 2698 lumens / Type III = 2652 lumens
4000K - Type II = 3076 lumens / Type III = 3023 lumens
5600K - Type II = 3277 lumens / Type III = 3221 lumens
3 Modules: 71 watts
3000K - Type II = 3909 lumens / Type III = 3865 lumens
4000K - Type II = 4457 lumens / Type III = 4407 lumens
5600K - Type II = 4750 lumens / Type III = 4696 lumens
NOTE : Due to rapid and continuous advances in LED technology, LED luminaire data is subject to change without notice and at
the discretion of HessAmerica. Consult factory for current technical data.
POLE
Fabricated aluminum bracket arm bolts to the pole 2.5' from the top with two stainless steel fasteners. Square tubing welded to
the underside of the bracket arm acts as a wire way for the luminaire power cable. Round and curved steel pole is manufactured
from cold drawn over mandrel, electric-weld, mechanical round steel tubing with nominal wall thickness of 0.157''. Pole
curvature projects centerline of pole top 1.7' from the base. Flush mounted handhole cover is plasma cut with kerf not to exceed
1/8'' and includes triangular tamper-resistant locking device. Pole is hot-dip galvanized with coating inside and out, then
lightly sanded prior to painting. Two-piece base cover with tamper-proof fasteners is fabricated from 0.080'' spun aluminum
and finished to match the pole. Nominal pole height is 17'.
FINISH
Housing is ultrasonically cleaned prior to painting. Standard finish is finely textured matte silver grey metallic or graphite grey.
Special colors available on request.
CERTIFICATION
UL Listed for Wet Locations
WARRANTY
Limited product warranty period including LEDs is three years. Driver shall carry the manufacturer's limited warranty.
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > CANTO G
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/CANTO_G/
Page 2
(please select finish)
TYPE S2 - 120/277V
Additional information
Dimensions
Mounting Detail
Specifications are subject to change without notification
HessAmerica > Products > Lighting Products > Pole Mounted Luminaire > CANTO G
http://www.hessamerica.com/Products/Lighting/Pole_Mounted_Luminaire/CANTO_G/
Page 3
TYPE S3 pole
(please advise finish)
International
Round Straight Steel Light Poles
POLE SHAFT:
Fabricated from hot rolled welded steel tubing with minimum
yield strength of 42,000 PSI.
ANCHOR BASE:
Structural quality ASTM A-36. The base is provided with bolt
slots to accommodate a 7" – 9" bolt circle.
ANCHOR BOLTS:
Carbon steel conforming to AASHTO M314 grade-55 or ASTM
F1554 grade-55. Bolts are "L" shaped and are galvanized a
minimum of 12" on the threaded end. Each pole includes four
bolts each with two nuts and two flat washers.
FULL BASE COVER (optional):
Two piece cover fabricated from ABS plastic.
MOUNTING
HEIGHT
HANDHOLE:
Covered 2 1/2" x 5" reinforced handhole. A nut holder is provided near the handhole and includes a 1/2"-13 UNC hex
head bolt and nut.
HARDWARE:
All structural fasteners are galvanized high strength carbon
steel. All other fasteners are galvanized or zinc plated or stainless steel.
REINFORCED
HANDHOLE
W/COVER
AND
GROUNDING
STANDARD FINISH:
Galvanized or powder coated. Consult factory for standard or
custom colors.
MOUNTINGS OPTIONS:
Tenons- standard 2 3/8" x 4" or 4" x 6" or removable pole cap
used in conjunction with side mounted fixtures.
4 - ANCHOR
BOLTS WITH
THREADED END
GALVANIZED 12”
MIN. EACH BOLT
FURNISHED
WITH 2 HEX
NUTS AND 2
FLATWASHERS
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
Serving our customers and
the industry with quality
products since 1973.
www.nafcointernational.com
8.5
(please advise finish)
TYPE S3 pole
Round Straight Steel Light Poles
POLE
CATALOG
NUMBER
RSS10-303C
NOMINAL
MOUNTING
HEIGHT (ft)
10
Max EPA AT: (Allows for 1.3 Gust Factor)
POLE
O.D.
INCHES
WALL
THICKNESS
INCHES
80
MPH
90
MPH
100
MPH
3.0
120
10.0
7.7
6.0
RSS10-404C
10
4.0
.120
19.1
15.0
12.2
RSS10-4545C
10
4.5
.120
24.5
19.5
15.8
RSS12-303C
12
3.0
.120
7.7
5.8
4.4
RSS12-404C
12
4.0
.120
15.0
11.8
9.5
RSS12-4545C
12
4.5
.120
19.8
15.7
12.7
RSS14-303C
14
3.0
.120
6.0
4.4
3.3
RSS14-404C
14
4.0
.120
12.2
9.4
7.6
RSS14-4545C
14
4.5
.120
16.2
12.8
10.3
RSS16-303C
16
3.0
.120
4.6
3.2
2.3
RSS16-404C
16
4.0
.120
9.6
7.4
5.9
RSS16-4545C
16
4.5
.120
13.1
10.2
8.2
RSS18-303C
18
3.0
.120
3.4
2.3
1.4
RSS18-404C
18
4.0
.120
7.6
5.7
4.5
RSS18-4545C
18
4.5
.120
10.5
8.2
6.5
RSS20-303C
20
3.0
.120
2.4
1.4
-
RSS20-404C
20
4.0
.120
6.0
4.4
3.4
RSS20-4545C
20
4.5
.120
8.5
6.6
5.2
RSS20-505C
20
5.0
.120
11.7
9.1
7.2
RSS25-404C
25
4.0
.120
2.8
1.9
1.3
RSS25-4545C
25
4.5
.120
4.8
3.6
2.7
RSS25-505C
25
5.0
.120
7.2
5.5
4.2
RSS25-505D
25
5.0
.180
12.1
9.4
7.4
RSS30-4545C
30
4.5
.120
2.3
1.5
1.0
RSS30-505C
30
5.0
.120
4.2
3.0
2.2
RSS30-505D
30
5.0
.180
8.0
6.5
4.7
1. All designs utilize .75" x 17" x 3" anchor bolts.
2. Pole base plate dimensions are the same for all
designs. See pole base detail drawing for dimensions.
3. Wind load includes 1.3 gust factor.
Variations in mounting heights listed are available.
POLE BASE AND HANDHOLE DETAIL
Dimensions and Specifications subject to change without notice.
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
www.nafcointernational.com
8.6
(please select finish)
TYPE S3 - 120/277V
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Catalog number:
Approvals:
2SB
ALT3P35 96L4K120/277
MW
Mtg.
Fixture
Finish
Electrical Module
See page 2
Options
See pages 3-4
Ordering Example: 1SA / ALT3P35/ 96L5K277/ WH/ A26
Select pole from Kim’s Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting.
Specifications
ALT96
Approx. Wt. = 30 lbs.
7L"
(197 mm)
26L"
(680 mm)
2"
(51 mm)
17"
(432 mm)
Speed
Mount
Adapter
TOP
SIDE
BOTTOM
4B"
(105 mm)
FRONT
3E"
(98 mm)
US Patent Numbers D674,950 S and D674,965 S.
Other Patents Pending.
Date:
Page: 1 of 5
Housing: One piece, low copper, aluminum extrusion is mechanically
secured with stainless steel fasteners to low copper aluminum die-cast
electrical compartment and end cap. The electrical compartment includes
an integral support arm for mounting directly to a surface mount pole
adaptor or a horizontal slipfitter. A solid barrier wall separates the optical
and electrical compartment for thermal control. Electrical compartment and
end cap covers are securely fastened with with two hinges and a single latch
at each cover. One piece silicone gaskets seal the compartments at the
barrier surface.
Optical Module: The high performance optic utilizes the IP66 rated
PicoPrism™ technology securely attached to internal heat sink modules
producing incredible uniformity and visual comfort. This PicoPrism optic
utilizes a canted prism lens aimed toward the task and spreads horizontally
to produce high lumen output as well as great uniformity. All the optical
modules are fastened to the body of the luminaire across the center as well
as around the perimeter.
Electrical Compartment: Available in voltages from 120V through 480V
@ 50/60Hz.Class 2 output with power factor >0.9 at full load in
accordance with the National Electrical Code, ANSI/NFPA 70. Integral
10kV surge suppression protection standard. To address inrush current,
slow blow fuse or type C/D breaker should be used. All electronic
components are UL and CSA recognized and mounted directly to a driver
tray for maximum heat dissipation and modularity. Module includes a
driver, LifeShield® temperature control device and surge protector. Driver is
rated for -40°C starting and has a 0-10V dimming interface for multi-level
illumination options. All electronic components are IP66 rated. 347V and
480V currents may have a step-down transformer.
Support Arm: Die-cast, low copper aluminum with splice access cover
and tool-less entry. A die-cast pole adaptor and an internal reinforcing plate
are provided with wire strain relief. The arm adaptor is square or circular
cut for specified pole size and shape. For field wire connections, a terminal
block is mounted in the arm cavity and accessible behind the splice access
cover. The block accepts #14 to #8 wire sizes and is factory prewired to the
electrical module quick-disconnect plug inside the electrical compartment.
Optional Horizontal Slip-fitter: Cast low copper aluminum with
stamped, splice access cover. A die-cast adaptor plate is provided to secure
the luminaire to 1-1/4” to 2” IPS pipe size arms. For field wire connections,
a terminal block is mounted in the arm cavity and accessible behind the
splice access cover. Accepts #14 to #8 wire sizes and is factory prewired to
electrical module quick-disconnect plug inside the electrical compartment.
Optional Wall Mount: The Altitude easily mounts to the wall. A cast
aluminum mounting plate is attached to the wall over the junction box. Bolt
the Speed Mount to the cover plate. Then install the assembly over the
mounting plate. Slide the luminaire into place for hands free wiring
and finishing.
Finish: Each luminaire receives a fade and abrasion resistant, electrostatically
applied, thermally cured, triglycidal isocyanurate (TGIC) polyester
powdercoat finish. Standard colors include (BL) Black, (DB) Dark Bronze,
(WH) White, (PS) Platinum Silver, (SG) Stealth Gray, (LG) Light Gray, and
(CC) Custom Color (Include RAL#).
Listed to: UL 1598 Standard for Luminaires - UL 8750 Standard for Safety
for Light Emitting Diode (LED) Equipment for use in Lighting Products and
CSA C22.2#250.0 Luminaires. RoHS compliant. Meets Buy American
provisions within ARRA. Suitable for wet locations.
CAUTION: Fixtures must be grounded in accordance with national,
state and/or local electrical codes, Failure to do so may result in serious
personal injury.
Kim Lighting reserves the right to change specifications without notice.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE S3 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 2 of 5
Standard Features
Mounting
3SY configuration is available
for round poles only.
Cat. No.:  1SA
 2SB
 2SL
 3ST
 3SY
 4SC
 1SW
0.97
1.61 1.61 1.78
n/a
EPA (Effective Projected Area)
ALT96
Fixture
Cat. No. designates fixture
and light distribution.
0.64
1.28
ALT
3x
P
Housing:
Optic:
P = PicoPrism™
ALT= Altitude
Distribution:
 1= Type I
 2= Type II
 3= Type III
 4= Type IV
 5 = Type V
x
35
 R = Type R Right
 L = Type L Left
Current:
 35 = 350 mA
 70 = 700 mA
Light Distribution:
TYPE I
Electrical Module
TYPE
TYPE III
TYPEIIIII
I
TYPE
TYPE
TYPE
RNFO
TYPE
TYPE
II TYPE
TYPE
TYPE
TYPE
IV
- NFO
TYPE
TYPE
IV-IV
NFO
IV-V
TYPE
V TYPE
TYPE
TYPE
TYPE
III -III
NFO
TYPE
III -NFO
IIIIV TYPE
IIIIV
-NFO
TYPE
L RV TYPETYPE
L R
Right
Right
Forward
Forward
Forward
Square
Square
Square LeftRight
Left
Throw
Throw
Throw
96L
x
Source:
96L =17"W x 26K"L
1 For
4K
x
Color Temperature:1
 2K = 580nm Amber2
 3K=3000K
 4K=4000K
 5K=5000K
120/277
x
Voltage:
120=120V
208=208V
240=240V
277=277V
347=347V
480=480V
custom optics and color temperature configurations, contact factory.
Friendly.
2 Turtle
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE L
Left
TYPE S3 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 3 of 5
Optional Features
Finish
TGIC powder coat.
Black
Color:
Cat. No.:  BL
Dark Bronze
 DB
Stealth Gray
 SG
Platinum Silver
White
 PS
 WH
Custom Color1
 CC
Custom colors subject to additional charges, minimum quantities and extended lead times.
Consult representative. Custom color description:
1
Wall Mounting
Cat. No. 1SW
Select from Mounting
on page 2.
The Altitude™ easily mounts to the wall. A cast
aluminum wall bracket is attached to the wall
over the junction box. Bolt the Speed Mount to
the cover plate. Then install the assembly over
the wall mount bracket. Side the luminaire into
place for hands free wiring and finishing.
Cover Plate
6J" x 11K"
Splice
Access
Cover
Speed
Mount
Adapter
5K"
(140 mm)
4J"
(108 mm)
10D"
(270 mm)
8L"
(222 mm)
11K"
(292 mm)
N"
(14 mm)
Mounting Plate
2L"
(70 mm)
Fusing (internal only):
Cat. No. (see chart
at right)
 No Option
High temperature fuse holders factory installed inside the fixture
housing. Fuse is included.
Cat. No.:  SF for 120, 277 and 347 Line Volts
 DF for 208, 240 and 480 Line Volts
Photocell Receptacle
Cat. No.  A26
 No Option
Rotatable photocell receptacle provided for NEMA base
photocell (by others).
Receptacle
Lenses
Cat. No.  FGL
(Glass)
 FPL
(Polycarbonate)
 No Option
One-piece flat glass or polycarbonate lens slips into reveal.
Extra silicone gasketing will be provided to retain a clear
optical compartment. (Only available for 350mA systems).
CAUTION: Use only when vandalism is anticipated to
be high.
Neighbor Friendly Optic:
Cat. No.  NFO
 No Option
Integrated Neighbor Friendly Optic on each PicoPrism™ module
to completely control unwanted backlight. Most effective with
Type III and IV distibutions.
Polycarbonate Lens
TYPE I
TYPE
I II
TYPE
TYPE
II III
TYPE
TYPE
IV
TYPE III -NFO
TYPE III
-NFO
Forward
Throw
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE
TYPE IV
IV- NFO
TYPE IV
- NFO
TYPE
V
Forward
Square
Throw
TYPE S3 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 4 of 5
Optional Features
Horizontal Slipfitter Mount
Cat. No.  HSF
 No Option
Replaces standard mounting arm with a cast aluminum
fitter to adapt to a horizontal 1J" to 2" pipe-size
mounting end (1D" to 2C" OD). The casting has a
+/- 5° adjustment to accommodate davit arms that are
not horizontal.
Vertical Slipfitter Mounts
Cat. No. includes Mounting
Cat. No. (See right)
 No Option
Allows fixture or fixtures with standard mounting arm to mount to a pole with a 2" pipe-size
tenon (2C" OD). Minimum 4" tenon length required.
Horizontal Slipfitter for
1J" to 2" Pipe-Size Mount
Specify configuration (1SA, 2SB, 2SL, 3ST, 3SY, 4SC) 4" round or square aluminum with flush
cap. Finish to match fixture and arm.
NOTE: 3Y only available on round slipfitter.
Cat. No.
 VSF-1SA
 VSF-2SB
 VSF-2SL
 VSF-3ST
 VSF-3SY
 VSF-4SC
Round
Cat. No.
 SVSF-1SA
 SVSF-2SB
 SVSF-2SL
 SVSF-3ST
 SVSF-4SC
Mounting Configuration
1SA-single arm mount
2SB-2 at 180°
2SL -2 at 90°
3ST -3 at 90°
3SY-3 at 120°
4SC-4 at 90°
Square
Wireless Control
Cat. No.  WIH-M
 No Option
In fixture WiHubb® wireless control module features on/off/variable and step dimming, SNAP
protocol mesh network, AES-128 encryption detection, occupancy sensor interface and intuitive,
user-friendly software. The most comprehensive and up to date information can be found at
http://www.hubbell-automation.com/products/wihubb_infixture_module/.
0-10V Dimming Interface
Driver has a 0-10V dimming interface with a dimming
range of 10-100%. Is compatible with most control
systems including Hubbell Building Automation
wiHUBB™. Approved dimmers include Lutron Diva
AVTV, Lutron Nova NFTV and NTFTV. Note: Not
compatible with current sourcing dimmers. Controls
compatible via Gray and Purple dimming lead.
Warranty
Standard Input Black (+)
White (-)
Green (GND)
Gray Dimming Lead (-)
Fixture
Housing
Purple Dimming Lead (+)
30 mA Max
Kim Lighting warrants Altitude™ products (“Product(s)”) sold by Kim Lighting to be free from
defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period
of ten (10) years for exterior housing paint finish(s), (iii) a period of six (6) years for LED Light
Engines (PicoPrisms™) and, (iv) a period of five (5) years for LED power components (LED
Driver, LifeShield® device), from the date of sale of such goods to the buyer as specified in Kim
Lighting shipment documents for each product. Occupancy sensors, Surge Protector, dimmers
and relay wiring components are covered by the manufacturer’s warranty.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE S3 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 5 of 5
Performance Data
Projected Lumen Maintenance
Spectroradiometric
3000K Average
Correlated Color Temp. CCT (K)
4200K Average
5100K Average
mA
50,000 hrs
100,000 hrs
350
N/A
N/A
700
93.52%
89.80%
2800K-3175K
3800K-4600K
4600K-5600K
Color Rendering Index (CRI)
≥75
≥70
≥65
Power Factor
>.90
>.90
>.90
Electrical - Drive Current @350mA
Volts - AC
Electrical - Drive Current @700mA
Amps - AC
System Watts
Volts - AC
Amps - AC
System Watts
120
0.87
104
120
1.87
224
208
0.50
104
208
1.08
224
240
0.43
104
240
0.93
224
277
0.38
104
277
0.81
224
347
0.30
104
347
0.65
224
480
0.22
104
480
0.47
224
Current - 350mA
B.U.G. Rating (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
B2 U0 G3
B2 U0 G3
B2 U0 G3
B1 U0 G3
B0 U0 G3
B3 U0 G2
B3 U0 G3
4200K
N/A
B3 U0 G3
B3 U0 G3
B2 U0 G3
B1 U0 G3
B0 U0 G3
B4 U0 G2
B3 U0 G3
5100K
N/A
B3 U0 G3
B3 U0 G3
B3 U0 G3
B1 U0 G3
B0 U0 G3
B4 U0 G2
B3 U0 G3
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
8113
8191
7006
7669
6723
7906
7980
4200K
N/A
10367
10467
8951
9800
8591
10103
10196
5100K
N/A
11268
11377
9730
10652
9338
10981
11083
Absolute Lumens
Current - 700mA
B.U.G. Rating (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
B3 U0 G3
B3 U0 G3
B3 U0 G3
B1 U0 G3
B1 U0 G4
B4 U0 G2
B4 U0 G4
4200K
N/A
B3 U0 G3
B3 U0 G4
B3 U0 G3
B1 U0 G4
B1 U0 G4
B4 U0 G3
B4 U0 G4
5100K
N/A
B3 U0 G3
B3 U0 G4
B3 U0 G3
B1 U0 G4
B1 U0 G4
B4 U0 G3
B4 U0 G4
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
Absolute Lumens
Temperature
3000K
N/A
13902
13884
11874
13296
11395
13401
13524
4200K
N/A
17763
17740
15172
16631
14561
17123
17282
5100K
N/A
19308
19283
16491
18467
15827
18612
18784
LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library.
For custom optics and color temperature configurations, contact factory.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE S4 pole
(please advise finish)
International
Round Straight Steel Light Poles
POLE SHAFT:
Fabricated from hot rolled welded steel tubing with minimum
yield strength of 42,000 PSI.
ANCHOR BASE:
Structural quality ASTM A-36. The base is provided with bolt
slots to accommodate a 7" – 9" bolt circle.
ANCHOR BOLTS:
Carbon steel conforming to AASHTO M314 grade-55 or ASTM
F1554 grade-55. Bolts are "L" shaped and are galvanized a
minimum of 12" on the threaded end. Each pole includes four
bolts each with two nuts and two flat washers.
FULL BASE COVER (optional):
Two piece cover fabricated from ABS plastic.
MOUNTING
HEIGHT
HANDHOLE:
Covered 2 1/2" x 5" reinforced handhole. A nut holder is provided near the handhole and includes a 1/2"-13 UNC hex
head bolt and nut.
HARDWARE:
All structural fasteners are galvanized high strength carbon
steel. All other fasteners are galvanized or zinc plated or stainless steel.
REINFORCED
HANDHOLE
W/COVER
AND
GROUNDING
STANDARD FINISH:
Galvanized or powder coated. Consult factory for standard or
custom colors.
MOUNTINGS OPTIONS:
Tenons- standard 2 3/8" x 4" or 4" x 6" or removable pole cap
used in conjunction with side mounted fixtures.
4 - ANCHOR
BOLTS WITH
THREADED END
GALVANIZED 12”
MIN. EACH BOLT
FURNISHED
WITH 2 HEX
NUTS AND 2
FLATWASHERS
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
Serving our customers and
the industry with quality
products since 1973.
www.nafcointernational.com
8.5
(please advise finish)
TYPE S4 pole
Round Straight Steel Light Poles
POLE
CATALOG
NUMBER
RSS10-303C
NOMINAL
MOUNTING
HEIGHT (ft)
10
Max EPA AT: (Allows for 1.3 Gust Factor)
POLE
O.D.
INCHES
WALL
THICKNESS
INCHES
80
MPH
90
MPH
100
MPH
3.0
120
10.0
7.7
6.0
RSS10-404C
10
4.0
.120
19.1
15.0
12.2
RSS10-4545C
10
4.5
.120
24.5
19.5
15.8
RSS12-303C
12
3.0
.120
7.7
5.8
4.4
RSS12-404C
12
4.0
.120
15.0
11.8
9.5
RSS12-4545C
12
4.5
.120
19.8
15.7
12.7
RSS14-303C
14
3.0
.120
6.0
4.4
3.3
RSS14-404C
14
4.0
.120
12.2
9.4
7.6
RSS14-4545C
14
4.5
.120
16.2
12.8
10.3
RSS16-303C
16
3.0
.120
4.6
3.2
2.3
RSS16-404C
16
4.0
.120
9.6
7.4
5.9
RSS16-4545C
16
4.5
.120
13.1
10.2
8.2
RSS18-303C
18
3.0
.120
3.4
2.3
1.4
RSS18-404C
18
4.0
.120
7.6
5.7
4.5
RSS18-4545C
18
4.5
.120
10.5
8.2
6.5
RSS20-303C
20
3.0
.120
2.4
1.4
-
RSS20-404C
20
4.0
.120
6.0
4.4
3.4
RSS20-4545C
20
4.5
.120
8.5
6.6
5.2
RSS20-505C
20
5.0
.120
11.7
9.1
7.2
RSS25-404C
25
4.0
.120
2.8
1.9
1.3
RSS25-4545C
25
4.5
.120
4.8
3.6
2.7
RSS25-505C
25
5.0
.120
7.2
5.5
4.2
RSS25-505D
25
5.0
.180
12.1
9.4
7.4
RSS30-4545C
30
4.5
.120
2.3
1.5
1.0
RSS30-505C
30
5.0
.120
4.2
3.0
2.2
RSS30-505D
30
5.0
.180
8.0
6.5
4.7
1. All designs utilize .75" x 17" x 3" anchor bolts.
2. Pole base plate dimensions are the same for all
designs. See pole base detail drawing for dimensions.
3. Wind load includes 1.3 gust factor.
Variations in mounting heights listed are available.
POLE BASE AND HANDHOLE DETAIL
Dimensions and Specifications subject to change without notice.
NAFCO International, Fond du Lac, WI 1-800-558-4810 Fax 1-920-921-0781
www.nafcointernational.com
8.6
(please select finish)
TYPE S4 - 120/277V
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Catalog number:
Approvals:
1SA
ALT3P35 96L4K120/277
MW
Mtg.
Fixture
Finish
Electrical Module
See page 2
Options
See pages 3-4
Ordering Example: 1SA / ALT3P35/ 96L5K277/ WH/ A26
Select pole from Kim’s Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting.
Specifications
ALT96
Approx. Wt. = 30 lbs.
7L"
(197 mm)
26L"
(680 mm)
2"
(51 mm)
17"
(432 mm)
Speed
Mount
Adapter
TOP
SIDE
BOTTOM
4B"
(105 mm)
FRONT
3E"
(98 mm)
US Patent Numbers D674,950 S and D674,965 S.
Other Patents Pending.
Date:
Page: 1 of 5
Housing: One piece, low copper, aluminum extrusion is mechanically
secured with stainless steel fasteners to low copper aluminum die-cast
electrical compartment and end cap. The electrical compartment includes
an integral support arm for mounting directly to a surface mount pole
adaptor or a horizontal slipfitter. A solid barrier wall separates the optical
and electrical compartment for thermal control. Electrical compartment and
end cap covers are securely fastened with with two hinges and a single latch
at each cover. One piece silicone gaskets seal the compartments at the
barrier surface.
Optical Module: The high performance optic utilizes the IP66 rated
PicoPrism™ technology securely attached to internal heat sink modules
producing incredible uniformity and visual comfort. This PicoPrism optic
utilizes a canted prism lens aimed toward the task and spreads horizontally
to produce high lumen output as well as great uniformity. All the optical
modules are fastened to the body of the luminaire across the center as well
as around the perimeter.
Electrical Compartment: Available in voltages from 120V through 480V
@ 50/60Hz.Class 2 output with power factor >0.9 at full load in
accordance with the National Electrical Code, ANSI/NFPA 70. Integral
10kV surge suppression protection standard. To address inrush current,
slow blow fuse or type C/D breaker should be used. All electronic
components are UL and CSA recognized and mounted directly to a driver
tray for maximum heat dissipation and modularity. Module includes a
driver, LifeShield® temperature control device and surge protector. Driver is
rated for -40°C starting and has a 0-10V dimming interface for multi-level
illumination options. All electronic components are IP66 rated. 347V and
480V currents may have a step-down transformer.
Support Arm: Die-cast, low copper aluminum with splice access cover
and tool-less entry. A die-cast pole adaptor and an internal reinforcing plate
are provided with wire strain relief. The arm adaptor is square or circular
cut for specified pole size and shape. For field wire connections, a terminal
block is mounted in the arm cavity and accessible behind the splice access
cover. The block accepts #14 to #8 wire sizes and is factory prewired to the
electrical module quick-disconnect plug inside the electrical compartment.
Optional Horizontal Slip-fitter: Cast low copper aluminum with
stamped, splice access cover. A die-cast adaptor plate is provided to secure
the luminaire to 1-1/4” to 2” IPS pipe size arms. For field wire connections,
a terminal block is mounted in the arm cavity and accessible behind the
splice access cover. Accepts #14 to #8 wire sizes and is factory prewired to
electrical module quick-disconnect plug inside the electrical compartment.
Optional Wall Mount: The Altitude easily mounts to the wall. A cast
aluminum mounting plate is attached to the wall over the junction box. Bolt
the Speed Mount to the cover plate. Then install the assembly over the
mounting plate. Slide the luminaire into place for hands free wiring
and finishing.
Finish: Each luminaire receives a fade and abrasion resistant, electrostatically
applied, thermally cured, triglycidal isocyanurate (TGIC) polyester
powdercoat finish. Standard colors include (BL) Black, (DB) Dark Bronze,
(WH) White, (PS) Platinum Silver, (SG) Stealth Gray, (LG) Light Gray, and
(CC) Custom Color (Include RAL#).
Listed to: UL 1598 Standard for Luminaires - UL 8750 Standard for Safety
for Light Emitting Diode (LED) Equipment for use in Lighting Products and
CSA C22.2#250.0 Luminaires. RoHS compliant. Meets Buy American
provisions within ARRA. Suitable for wet locations.
CAUTION: Fixtures must be grounded in accordance with national,
state and/or local electrical codes, Failure to do so may result in serious
personal injury.
Kim Lighting reserves the right to change specifications without notice.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE S4 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 2 of 5
Standard Features
Mounting
3SY configuration is available
for round poles only.
Cat. No.:  1SA
 2SB
 2SL
 3ST
 3SY
 4SC
 1SW
0.97
1.61 1.61 1.78
n/a
EPA (Effective Projected Area)
ALT96
Fixture
Cat. No. designates fixture
and light distribution.
0.64
1.28
ALT
3x
P
Housing:
Optic:
P = PicoPrism™
ALT= Altitude
Distribution:
 1= Type I
 2= Type II
 3= Type III
 4= Type IV
 5 = Type V
x
35
 R = Type R Right
 L = Type L Left
Current:
 35 = 350 mA
 70 = 700 mA
Light Distribution:
TYPE I
Electrical Module
TYPE
TYPE III
TYPEIIIII
I
TYPE
TYPE
TYPE
RNFO
TYPE
TYPE
II TYPE
TYPE
TYPE
TYPE
IV
- NFO
TYPE
TYPE
IV-IV
NFO
IV-V
TYPE
V TYPE
TYPE
TYPE
TYPE
III -III
NFO
TYPE
III -NFO
IIIIV TYPE
IIIIV
-NFO
TYPE
L RV TYPETYPE
L R
Right
Right
Forward
Forward
Forward
Square
Square
Square LeftRight
Left
Throw
Throw
Throw
96L
x
Source:
96L =17"W x 26K"L
1 For
4K
x
Color Temperature:1
 2K = 580nm Amber2
 3K=3000K
 4K=4000K
 5K=5000K
120/277
x
Voltage:
120=120V
208=208V
240=240V
277=277V
347=347V
480=480V
custom optics and color temperature configurations, contact factory.
Friendly.
2 Turtle
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE L
Left
TYPE S4 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 3 of 5
Optional Features
Finish
TGIC powder coat.
Black
Color:
Cat. No.:  BL
Dark Bronze
 DB
Stealth Gray
 SG
Platinum Silver
White
 PS
 WH
Custom Color1
 CC
Custom colors subject to additional charges, minimum quantities and extended lead times.
Consult representative. Custom color description:
1
Wall Mounting
Cat. No. 1SW
Select from Mounting
on page 2.
The Altitude™ easily mounts to the wall. A cast
aluminum wall bracket is attached to the wall
over the junction box. Bolt the Speed Mount to
the cover plate. Then install the assembly over
the wall mount bracket. Side the luminaire into
place for hands free wiring and finishing.
Cover Plate
6J" x 11K"
Splice
Access
Cover
Speed
Mount
Adapter
5K"
(140 mm)
4J"
(108 mm)
10D"
(270 mm)
8L"
(222 mm)
11K"
(292 mm)
N"
(14 mm)
Mounting Plate
2L"
(70 mm)
Fusing (internal only):
Cat. No. (see chart
at right)
 No Option
High temperature fuse holders factory installed inside the fixture
housing. Fuse is included.
Cat. No.:  SF for 120, 277 and 347 Line Volts
 DF for 208, 240 and 480 Line Volts
Photocell Receptacle
Cat. No.  A26
 No Option
Rotatable photocell receptacle provided for NEMA base
photocell (by others).
Receptacle
Lenses
Cat. No.  FGL
(Glass)
 FPL
(Polycarbonate)
 No Option
One-piece flat glass or polycarbonate lens slips into reveal.
Extra silicone gasketing will be provided to retain a clear
optical compartment. (Only available for 350mA systems).
CAUTION: Use only when vandalism is anticipated to
be high.
Neighbor Friendly Optic:
Cat. No.  NFO
 No Option
Integrated Neighbor Friendly Optic on each PicoPrism™ module
to completely control unwanted backlight. Most effective with
Type III and IV distibutions.
Polycarbonate Lens
TYPE I
TYPE
I II
TYPE
TYPE
II III
TYPE
TYPE
IV
TYPE III -NFO
TYPE III
-NFO
Forward
Throw
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE
TYPE IV
IV- NFO
TYPE IV
- NFO
TYPE
V
Forward
Square
Throw
TYPE S4 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 4 of 5
Optional Features
Horizontal Slipfitter Mount
Cat. No.  HSF
 No Option
Replaces standard mounting arm with a cast aluminum
fitter to adapt to a horizontal 1J" to 2" pipe-size
mounting end (1D" to 2C" OD). The casting has a
+/- 5° adjustment to accommodate davit arms that are
not horizontal.
Vertical Slipfitter Mounts
Cat. No. includes Mounting
Cat. No. (See right)
 No Option
Allows fixture or fixtures with standard mounting arm to mount to a pole with a 2" pipe-size
tenon (2C" OD). Minimum 4" tenon length required.
Horizontal Slipfitter for
1J" to 2" Pipe-Size Mount
Specify configuration (1SA, 2SB, 2SL, 3ST, 3SY, 4SC) 4" round or square aluminum with flush
cap. Finish to match fixture and arm.
NOTE: 3Y only available on round slipfitter.
Cat. No.
 VSF-1SA
 VSF-2SB
 VSF-2SL
 VSF-3ST
 VSF-3SY
 VSF-4SC
Round
Cat. No.
 SVSF-1SA
 SVSF-2SB
 SVSF-2SL
 SVSF-3ST
 SVSF-4SC
Mounting Configuration
1SA-single arm mount
2SB-2 at 180°
2SL -2 at 90°
3ST -3 at 90°
3SY-3 at 120°
4SC-4 at 90°
Square
Wireless Control
Cat. No.  WIH-M
 No Option
In fixture WiHubb® wireless control module features on/off/variable and step dimming, SNAP
protocol mesh network, AES-128 encryption detection, occupancy sensor interface and intuitive,
user-friendly software. The most comprehensive and up to date information can be found at
http://www.hubbell-automation.com/products/wihubb_infixture_module/.
0-10V Dimming Interface
Driver has a 0-10V dimming interface with a dimming
range of 10-100%. Is compatible with most control
systems including Hubbell Building Automation
wiHUBB™. Approved dimmers include Lutron Diva
AVTV, Lutron Nova NFTV and NTFTV. Note: Not
compatible with current sourcing dimmers. Controls
compatible via Gray and Purple dimming lead.
Warranty
Standard Input Black (+)
White (-)
Green (GND)
Gray Dimming Lead (-)
Fixture
Housing
Purple Dimming Lead (+)
30 mA Max
Kim Lighting warrants Altitude™ products (“Product(s)”) sold by Kim Lighting to be free from
defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period
of ten (10) years for exterior housing paint finish(s), (iii) a period of six (6) years for LED Light
Engines (PicoPrisms™) and, (iv) a period of five (5) years for LED power components (LED
Driver, LifeShield® device), from the date of sale of such goods to the buyer as specified in Kim
Lighting shipment documents for each product. Occupancy sensors, Surge Protector, dimmers
and relay wiring components are covered by the manufacturer’s warranty.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
TYPE S4 - 120/277V
(please select finish)
ALT96
ALTITUDE™ LED
3/13/14 • kl_alt96_spec.pdf
Type:
Job:
Page: 5 of 5
Performance Data
Projected Lumen Maintenance
Spectroradiometric
3000K Average
Correlated Color Temp. CCT (K)
4200K Average
5100K Average
mA
50,000 hrs
100,000 hrs
350
N/A
N/A
700
93.52%
89.80%
2800K-3175K
3800K-4600K
4600K-5600K
Color Rendering Index (CRI)
≥75
≥70
≥65
Power Factor
>.90
>.90
>.90
Electrical - Drive Current @350mA
Volts - AC
Electrical - Drive Current @700mA
Amps - AC
System Watts
Volts - AC
Amps - AC
System Watts
120
0.87
104
120
1.87
224
208
0.50
104
208
1.08
224
240
0.43
104
240
0.93
224
277
0.38
104
277
0.81
224
347
0.30
104
347
0.65
224
480
0.22
104
480
0.47
224
Current - 350mA
B.U.G. Rating (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
B2 U0 G3
B2 U0 G3
B2 U0 G3
B1 U0 G3
B0 U0 G3
B3 U0 G2
B3 U0 G3
4200K
N/A
B3 U0 G3
B3 U0 G3
B2 U0 G3
B1 U0 G3
B0 U0 G3
B4 U0 G2
B3 U0 G3
5100K
N/A
B3 U0 G3
B3 U0 G3
B3 U0 G3
B1 U0 G3
B0 U0 G3
B4 U0 G2
B3 U0 G3
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
8113
8191
7006
7669
6723
7906
7980
4200K
N/A
10367
10467
8951
9800
8591
10103
10196
5100K
N/A
11268
11377
9730
10652
9338
10981
11083
Absolute Lumens
Current - 700mA
B.U.G. Rating (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare
Temperature
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
3000K
N/A
B3 U0 G3
B3 U0 G3
B3 U0 G3
B1 U0 G3
B1 U0 G4
B4 U0 G2
B4 U0 G4
4200K
N/A
B3 U0 G3
B3 U0 G4
B3 U0 G3
B1 U0 G4
B1 U0 G4
B4 U0 G3
B4 U0 G4
5100K
N/A
B3 U0 G3
B3 U0 G4
B3 U0 G3
B1 U0 G4
B1 U0 G4
B4 U0 G3
B4 U0 G4
TYPE 1
TYPE 2
TYPE 3
TYPE 3 NFO
TYPE 4
TYPE 4 NFO
TYPE 5
TYPE L/R
Absolute Lumens
Temperature
3000K
N/A
13902
13884
11874
13296
11395
13401
13524
4200K
N/A
17763
17740
15172
16631
14561
17123
17282
5100K
N/A
19308
19283
16491
18467
15827
18612
18784
LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library.
For custom optics and color temperature configurations, contact factory.
© 2014 KIM LIGHTING • 16555 East Gale Avenue, City of Industry, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716
(please advise finish)
TYPE S5 ve - 120/277V
TLED-b
dome top led bollard
Model Number:
Accessories:
Job:Type:
Approvals:
DESCRIPTION
The TLED-B series bollard’s traditional design combined with a high
performance LED light source and superior thermal management makes
it an attractive, energy saving choice. Every aspect of the TLED-B series
design has been engineered to provide a LED bollard that delivers optimum
optical performance and longevity in an attractive, durable housing. The
TLED-B housing uses a UV resistant powder coated finish to protect
against the elements and is ETL listed for wet locations. Available 24 LED
light engine with 27.5w total system watts while delivering over 1000 initial
lumens output, the TLED-B bollard provides a wide spectrum of application
options for lighting pedestrian walkways, retail entryways, as well as lighting
sidewalks in schools, office buildings, and apartment complexes.
SPECIFICATIONS
Construction:
An extruded aluminum housing features clean architectural lines with ample,
integral mounting space for many optional accessories, the TLED-B’s most
important construction feature is its integrated thermal management, which
allows for optimum performance and durability of the LED light engine
without sacrificing design aesthetics. The TLED-B is completely sealed and
gasketed, is ETL listed for wet locations, and has tamper resistant hardware,
making it a perfect choice for tamper resistant applications. TLED-B also
incorporates a UV resistant, long lasting, polyester based powder coated
finish.
Optics:
Our TLED-B series bollard delivers exceptional light quality, efficiency and
light distribution with an optical design that provides even light distribution.
The TLED-B’s textured silver, internal reflector is specifically designed
to diffuse and distribute light where it is needed in the most efficient way
possible.
Electrical:
The 24 LED SSL light engine in the TLED-B draws 27.5 watts total, including
the driver. The TLED-B is powered by constant voltage control driver and
provides a 100,000 hour rated life with 70% lumen maintenance, a 4700K
CCT, and a CRI of ≥75. All drivers are Class 2 power supplies with input
voltage range of 120VAC to 277VAC, providing a Class A EMI rating and a
high power factor of ≥0.90. The TLED-B is suitable for operation in -40°C
(-40°F) to 40°C (104°F) ambient conditions.
Thermal Management:
LEDLITElogic heat sinking technology moves heat away from the LEDs by
utilizing a patent-pending “chimney” design that takes advantage of thermal
convection dynamics maximizing system performance and delivering a
100,000 hour life with 70% lumen maintenance.
SPECIFICATIONS ARE SUBJECT
TO CHANGE WITHOUT NOTICE
Environmentally Friendly Design:
TLED-B luminaires consume very little energy and provide long life in
comparison to traditional lamp technologies. Our manufacturing process
utilizes no hazardous substances such as mercury or lead . The TLED-B is
RoHS (Restriction of Hazardous Substances) compliant, 100% recyclable,
and provides a significant reduction in Kw load and carbon emissions.
Installation:
The TLED-B series features a sturdy base plate that is anchored with three
J-bolts. The bollard body easily attaches to the base plate by three tamperresistant fasteners and the bollard top is attached to the body using three
more tamper-resistant fasteners.
Transient Protection System (Option: TP):
The LEDLITElogic optional transient protection device is designed to be
used in conjunction with our LED drivers. The “-TP” option utilizes a 3-leaded
device that protects Line-Ground, Line-Neutral, and Neutral-Ground in
accordance with IEEE/ANSI C62.41.2 guidelines. The surge current rating
of the “-TP” option is 10,000 amps.
Testing & Compliance:
The reliability and performance of the TLED-B is evaluated in accordance
with the parameters outlined and reported by LM-79 and LM-80 documents.
Photometric data is tested to IESNA LM-79-08 standard by an independent
testing laboratory. Lumen maintenance, L70 a measure of long term
reliability, is determined for the light source, which consists of the LED and
PCB sub-assembly as installed in the luminaire, is determined using LM-80
in situ thermal and reliability data as provided by the LED manufacturer in
accordance with DOE/EPA standards.
108002340 06/13
Listing:
The TLED-B is ETL certified under UL1598 specifications and listed for wet
locations.
Warranty:
Any component that fails due to manufacturer’s defect is guaranteed for
5 years. The warranty does not cover physical damage, abuse or acts of
God. Manufacturer reserves the right to charge for such repairs if deemed
necessary.
(please advise finish)
Fixture Performance
TYPE S5 ve - 120/277V
Sample Photometrics
Part Number
Initial
Lumens
Lumens per
Watt (LPW)
Total
Watts
L70 Hours
@ 25°C
BUG
Ratings
TLED-B-24-DT
1012
37
27.5
100,000
B1-U2-G1
TLED-B-24 (Type V Short Non-Cutoff)
20’
15’
NOTE: Lumen maintenance and life (part of LM-80 data) are per published information from
primary LED suppliers and is based on design operation at their specified thermal management
and electrical design parameters.
.1fc
10’
.5fc
1fc
5’
Dimensions
5fc
0
5’
10’
39.5”
15’
20’
0
5’
10’
15’
20’
6.9”
Mounting Template
3/8" Diameter Bolt Hole
4.5" Diameter Circle
Ordering Information
Example: TLED-B-24-DT-SLV-TP
Series
TLED-B
# of LEDs
24 = 24 LEDs
Input Voltage
DT = 120/277VAC
Finish
Options (Factory Installed)
Accessories4 (Field Installed)
BL = Black
SZXXX1
TLED-347VST3 = 347VAC Step Down Transformer
SLV = Silver
TP = Transient Protection System
Notes
1
Specify voltage
2
Consult factory for specific part number and details
3
Step down transformer installed by others (may affect UL listing)
CC2
= Single Line Side Fuse (Specify 120 or 277V)
TLED-480VST3 = 480VAC Step Down Transformer
= Custom Color
1911 W. Parkside Lane • Phoenix, AZ 85027
(800) 533-3948 • Fax: (623) 580-8948
www.barronltg.com
(please advise finish)
TYPE S5 - 120/277V
LIGHTSCALE™ BOLLARD
PRODUCT DATA
With its smooth, organic lines and subtly curved profile, the LightScale Bollard is designed to settle harmoniously into any natural setting. Originally
conceived as a path light, its gentle arc allows mounting beside a walkway or street, providing light without taking up walk space.
MATERIAL & CONSTRUCTION DETAILS
INSTALLATION & MAINTENANCE
COLUMN
FINISH
LAMP
INSTALLATION
• Column is made from a formed
aluminum extrusion.
• Standard powdercoat colors are
Aluminum Texture and Slate Texture.
Optional colors from the F+S color chart
and custom RAL colors are available for
an upcharge.
• Linear fluorescent lamps are offered in
40W or 55W. See lamp information
on page 2.
• Standard 1/4" (6 mm) thick stainless
steel mounting plate bolted to main body
of extrusion in three places with 1/4-20
recessed security socket caps screws.
1/2-13 anchor bolts and template
included.
• Due to the inherent nature of metal
castings, gloss powdercoats are not
offered for cast components.
TOP CAP
WEIGHT
BALLAST
MAINTENANCE
• Cast aluminum cap is attached with
recessed security socket cap screws.
• 27 lbs (12 kg)
• Electronic, thermally protected, 120V or
277V ballast for 40W or 55W single twin
tube 4-pin fluorescent lamp, instant
start, -20 ºF starting temperature.
• Metal surfaces can be cleaned as
needed using a soft cloth or brush with
warm water and a mild detergent. Avoid
abrasive cleaners.
NOMINAL DIMENSIONS
BASE PLATE MOUNTING DETAIL
top cap
custom bent
aluminum extrusion
housing
42"
(1058 mm)
0.63" (16 mm) dia. thru
for 1/2-13 anchor bolts
typ (3) holes
2.0" (51 mm)
dia. thru for
conduit opening
2.5"
(63.5 mm)
5.0"
(127 mm)
UV-stabilized white
acrylic lens
5.75"
(146 mm)
lamp
8.24"
(209 mm)
socket for 2G11 base
ballast within waterproof
enclosure
conduit with wire
whip (not shown)
base plate with
anchor bolts and
cutout for conduit
18.0" (457 mm)
min. for cast-inplace J-bolts
cast-in-place J-bolt
anchors (drop-in type
anchors may also be
used)
poured concrete footer
T 800.451.0410 | www.forms-surfaces.com
© 2014 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 3 | Rev. 01-10-14
(please advise finish)
TYPE S5 - 120/277V
LIGHTSCALE™ BOLLARD
PRODUCT DATA
LAMP DESCRIPTIONS
LAMP
DESCRIPTION
BASE
INITIAL LUMENS
COLOR TEMPERATURE
FT55 BX
55W single twin tube 4-pin fluorescent
2G11
4,800
4,100
FT40 BX
40W single twin tube 4-pin fluorescent
2G11
3,150
4,100
POLAR CANDELA PLOT
0-180º
90-270º
ISOFOOTCANDLE PLOT
706
18.0'
529
12.0'
353
6.0'
176
0'
3
10
5
2
1
.5 .75
-6.0'
.25
-12.0'
-18.0'
-12.0'
18.0'
12.0'
6.0'
0'
-6.0'
-18.0'
Isofootcandle Plot shows light distribution pattern at ground level with 55W
fluorescent 2G11 base lamp. Readings have been taken assuming the
photometric center of the luminaire to be 2.40 feet above ground level. IES
files for standard lamps are available on our website.
Polar Candela Plot shows luminous intensity distribution (Cd/1000lm)
for vertical plane through specified horizontal angles (above) with 55W
fluorescent 2G11 base lamp. IES files for standard lamps are available on
our website.
CERTIFICATION
• UL and C-UL listed for wet locations.
ENVIRONMENTAL CONSIDERATIONS
• Please refer to the LightScale Bollard Environmental Data Sheet for detailed environmental impact information.
• Metal components have a long life cycle and are 100% recyclable.
• 68% recycled content.
• Powdercoat finishes are no- or low-VOC, depending on color.
• Low maintenance; easy to disassemble.
LAMP DESCRIPTIONS AND FOOTCANDLE MULTIPLIERS
LAMP
DESCRIPTION
BASE
INITIAL LUMENS
COLOR TEMPERATURE
FT55 BX
55W single twin tube 4-pin fluorescent
2G11
4700
4,100
FT40 BX
40W single twin tube 4-pin fluorescent
2G11
3150
4,100
T 800.451.0410 | www.forms-surfaces.com
© 2014 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 3 | Rev. 01-10-14
(please advise finish)
TYPE S5 - 120/277V
LIGHTSCALE™ BOLLARD
PRODUCT DATA
NET PRICING AND ORDERING INFORMATION (pricing does not include freight)
MODEL
LBLSC-CF
DESCRIPTION
LightScale Bollard
Optional Powdercoat color from Forms+Surfaces standard color chart
Custom RAL Powdercoat color
NET PRICE
please call for pricing
+ $200 per color/per order
+ minimum $500 per color/per order
TO ORDER SPECIFY: quantity, powdercoat color, lamp, voltage.
LEAD TIME: 6 to 8 weeks. Shorter lead times may be available upon request. Please contact us to discuss your specific timing requirements.
T 800.451.0410 | www.forms-surfaces.com
© 2014 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 3 | Rev. 01-10-14