Single Pole (One location) or 3-Way (Multi-location)
Magnetic Low-Voltage Slide Dimmer
120VAC, 60Hz
Cat. No. 6613-PL, 600VA
DI-00X-06613-02A
INSTALLATION INSTRUCTIONS
WARNINGS:
CAUTIONS:
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult a qualified electrician.
• To avoid overheating and possible damage to this device and other equipment, do not install to control a
receptacle, fluorescent lighting, a motor- or a transformer-operated appliance.
• Use with magnetic low-voltage transformers, incandescent, or 120V halogen fixtures only. Use a Leviton
electronic low-voltage dimmer to control electronic (solid state) low-voltage transformers.
• When magnetic low-voltage circuits are operated at a dim level, with all lamps inoperative, excess current may
flow through the transformer. To avoid possible transformer failure due to overcurrent, use a transformer that
incorporates thermal protection or a fuse at the primary windings.
• Use only one (1) dimmer in a 3- or 4-way circuit. The switch(es) will turn the light on at the brightness level
selected at the dimmer.
• Disconnect power at circuit breaker or fuse when servicing fixture.
• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.
Tools needed to install your Dimmer:
INSTALLING YOUR DIMMER
Slotted/Philips Screwdriver
Pliers
Cutters
NOTE: Use check boxes
Electrical Tape
Pencil
Ruler
√
Step 4 Disconnecting switch wires and preparing wires:
when Steps are completed.
Step 1 WARNING: To avoid fire, shock, or death; TURN OFF
Installing Dimmer by itself or with other devices:
• Disconnect wires from screw terminals or
Quickwire™ slots (shown).
POWER at circuit breaker or fuse and test that power is off
before wiring!
• Pull off pre-cut insulation from Dimmer
leads.
If installing Dimmer in a single device application, proceed with the
INSTALLING YOUR DIMMER section. If installing Dimmer in a multidevice application, proceed as follows:
MULTI-DEVICE APPLICATION:
In multi-dimmer installations, the reduction of the dimmer’s capacity is
required. Refer to the chart for maximum load per dimmer.
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
• Make sure that the ends of the wires from
the wall box are straight (cut if
necessary).
• Remove 5/8" (1.6 cm) of insulation from
each wire in the wall box (shown).
• For Single-Pole Application, go to Step
5A.
MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE
Cat. No.
Single
6613-PL
600VA
More than
Two Devices 2 Devices
500VA
400VA
Step 2 Removing existing switch: Remove existing wallplate
Press in slot and
pull out wire
• For 3-Way Application, go to Step 5B.
and switch mounting screws. Carefully pull switch from wall
box. DO NOT remove wires attached to the switch at this
time.
Step 3 Identifying your wiring application (most
Strip 5/8"
common):
5/8"
NOTE: If the wiring in the wall box does not resemble any of
these configurations, consult a qualified electrician.
MAXIMUM BULB WATTAGE:
Low-voltage dimmers are rated in Volt-Amps (VA). The maximum bulb
wattage is determined by the efficiency of the transformer in the lowvoltage lighting system. Transformer efficiencies will vary from different
manufacturers; consider 75% efficient as average. Use the chart to
determine maximum bulb wattage for typical transformer efficiency
ratings.
MAXIMUM BULB WATTAGE AT 75% EFFICIENCY
Rating
Single
Two
Gang
More than
2 Gang
600VA
450W
375W
300W
Tag Common
Screw Wire
Single-Pole:
Look at the back of your switch.
If there are 2 wires connected to
two screw terminals (not
including a green or bare copper
wire used for grounding), you
have a Single-Pole switch.
3-Way:
Look at the back of your switch. If there
are 3 wires connected to three screw
terminals (not including a green or bare
copper wire used for grounding), you
have a 3-Way switch. Note that one of
the screw terminals will usually be a
different color (black) or labeled
Common. Tag that wire with electrical
tape to identify.
Cut
(if necessary)
Strip Gage
Step 5a Single-Pole Wiring Application using 3-Way
Dimmer:
This wire is used in 3-way installations only.
For single pole installations, do not remove this insulating label.
Step 5b
con’t
Dimmer
Hot (Black)
Insert wires
straight then
twist
clockwise
Red
Black
3-Way Switch
Common
Terminal
(Black Screw)
Red
Black
}
Green
Ground
Green
Ground
Load
White
Neutral
Neutral (White)
Red
Ground
Electrical
Tape
Green
Black
Dimmer
Hot (Black)
Black
Red
(PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
Black
Red
}
Line 120VAC, 60 Hz
Green Ground
Load
White
fuse. Installation is complete.
(PRIMARY SIDE OF
MAGNETIC LOW-VOLTAGE
TRANSFORMER)
Red
Line
120VAC, 60Hz
Step 8 Restore Power: Restore power at circuit breaker or
Connect wires per WIRING DIAGRAM as follows:
Screw wire nuts on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
WARNING: CONNECT A MAGNETIC LOW-VOLTAGE
DIMMER ONLY TO THE PRIMARY (HIGH-VOLTAGE) SIDE
OF A MAGNETIC LOW-VOLTAGE TRANSFORMER.
NOTE: Dimmer can be installed on either the Load or Line side.
• Green dimmer Ground lead to Green or bare copper
wire in wall box.
• Black dimmer lead to tagged (common) wall box wire
identified when removing old switch.
• Remove Red insulating label from Red lead.
• Any Red dimmer lead to any of the remaining wall box wires.
• Remaining Red dimmer lead to remaining wall box wire.
OPERATION
NOTE: If using the indicator light option, the light will illuminate
when the Load is OFF to facilitate access in the dark.
NOTE: If using the dimmer in a 3-way application, the lights will
turn ON at the level the slider is set for both single pole and 3-way
applications. The lighting can be controlled from either the dimmer
or the switch location.
TOP
ON: Push rocker switch ON.
OFF: Push rocker switch OFF.
BRIGHTEN: Raise slider control lever to
desired level of light.
DIM: Lower slider control lever to desired
level of light.
Neutral (White)
Connect wires per WIRING DIAGRAM as follows:
Screw wire nuts on clockwise making sure no bare
conductors show below the wire connectors. Secure each
connector with electrical tape.
WARNING: CONNECT A MAGNETIC LOW-VOLTAGE
DIMMER ONLY TO THE PRIMARY (HIGH-VOLTAGE) SIDE
OF A MAGNETIC LOW-VOLTAGE TRANSFORMER.
• Green dimmer Ground lead to Green or bare copper
wire in wall box.
• Black dimmer lead to any wall box wire removed
from old switch.
• Red dimmer lead without insulating label to remaining
wall box wire.
• Remaining Red dimmer lead should have Red insulation
label affixed. Proceed to Step 6.
NOTE: If insulating label is not affixed to Red lead, use
a small wire nut or electrical tape to cap off. Proceed to
Step 6.
Step 6 Testing your Dimmer prior to mounting in wall
box:
NOTE: This device is shipped with the indicator light enabled
(On). If you do not want the light option (Off), with an insulated
screwdriver slide the switch at the TOP of the frame to the right
while facing the device before mounting wallplate.
Indicator
Slide Switch
Step 5b 3-Way Wiring Application:
• Restore power at circuit
breaker or fuse.
• Carefully holding Dimmer as
shown, slide control lever to
highest postion. If lights are
not ON, press rocker. Lights
should turn ON to brightest
level.
If lights do not turn ON,
refer to the
TROUBLESHOOTING
section.
Step 7 Dimmer Mounting:
Neutral
Red
Insert wires
straight then
twist
clockwise
Red
Ground
Green
Black
Tag
Electrical
Tape
TROUBLESHOOTING
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly with wire connectors.
• Light does not turn ON and ON/OFF LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp Neutral connection is not wired.
NOTE: If further information is needed in identifying the HOT wire in a
3-Way application, go to Leviton's website at www.leviton.com.
For non-standard wiring applications, refer to
Wire Nut and Connector Size Chart
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
1212-
#12
#12
#14
#14
w/
w/
w/
w/
1
1
1
1
to 3 #14, #16 or #18
or 2 #16 or #18
to 4 #16 or #18
to 3 #16 or #18
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
TOP
Installation may now be
completed by carefully
positioning all wires to
provide room in wall box for
dimmer. Mount dimmer
into box with mounting
screws supplied. Attach
Decora® wallplate.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s
only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance
Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper
environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and
fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this
warranty, whether based on contract, tort or otherwise.
DI-00X-06613-02A
Product
Specifications
SureSlide
SureSlide™ Decora Slide Dimmers
1.73 (43.9 mm)
1.34
(34.0 mm)
2.63 (66.8 mm)
4.13 (104.9 mm)
SureSlide
1.30
(33.0 mm)
1.53 (38.9 mm)
Cat. No. 6621-P
APPLICATION
Leviton SureSlide™ Decora-style dimmers provide smooth, slide-action full-range dimming for incandescent, magnetic low-voltage, magnetic
fluorescent and electronic fluorescent lighting. Preset versions feature a separate Preset ON/OFF switch to allow ON/OFF switching without
disturbing the selected brightness level. SureSlide also offers full-range fan speed controls and quiet fan speed controls. The SureSlide line
includes single-pole (one location), Preset 3-way (multi-location), and illuminated versions. Suitable for a wide range of residential and
commercial applications, SureSlide is compatible with Leviton’s entire line of Decora designer-style devices.
FEATURES
• UL Listed (File # E-31373)
• CSA Certified (File # LR-3413)
• All SureSlide devices have a permanently mounted smoothaction integrated linear slide control for easy, precise operation.
• SureSlide Slide Dimmers and Fan Speed Controls offer full range
slide control. Preset versions feature a separate ON/OFF Preset
switch that does not disturb the selected brightness or fan speed
settings.
• SureSlide dimmers and fan speed controls feature elegant
Decora styling that coordinates perfectly with Leviton’s extensive
line of Decora wiring devices.
• SureSlide lighting controls are available in single-pole, 3-way and
illuminated versions
• SureSlide features models specifically designed for Advance Mark
XTM and Philips EcotronTM fluorescent dimming ballasts and the
Philips dimmable EarthlightTM.
• Built-in radio/TV interference filter.
• Preset versions provide a low-end trim adjustment feature allows
precise adjustment of lamp brightness or fan speed at low-end
setting.
• SureSlide Quiet Fan Speed Controls have special circuitry to
reduce fan motor noise at low speeds.
• Use with Leviton DPSPE-112 Power Extender to extend load
capacity to 2000W (2000VA) for incandescent, magnetic lowvoltage and Advance Mark X™ fluorescent dimming ballasts.
• Use with Leviton DPSPE-212 Power Extender to extend load
capacity to 2000VA for Advance Mark VII™ and Motorola Helios™
fluorescent ballasts.
• SureSlide features a slim, compact housing that fits easily into a
standard wallbox and is suitable for multi-gang installations.
• Most SureSlide devices are available in brown, ivory, white, gray
and black (illuminated versions available in ivory and white only).
Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362 • Phone: (800) 323-8920 • Fax: (800) 832-9538
L25
Product
Specifications
SureSlide
.........................
STANDARDS SPECIFICATIONS
Controls shall be UL Listed Leviton Multi-Location Decora Slide Dimmer with Limited Two-Year Warranty, permanently mounted
smooth-action integrated linear slide control mechanism for precise operation, Leviton Decora styling and compact housing that fits
easily into standard wallbox. Preset version shall be available. Quiet Fan Speed Controls shall have special circuitry to reduce fan motor
noise at low speeds and low-end trim adjustment for minimum fan speed. Available in ratings and colors as scheduled on plan.
Performance Specifications
Electrical
• Input 120 VAC @ 60Hz.
• Line voltage regulation.
• RFI noise suppression.
• Maximum load incandescent 600 watts stand alone.
Mechanical
• Dimmer control – slide bar.
• On/off rocker switch.
• 3-way versions work with a 3-way switch.
• Two wire device plus ground wire; three wire plus ground wire on 3-way
• The LED will be lighted when the device switches the load off.
• On/off switch provides air-gap switch for servicing.
Environmental
• Operating 0 degrees celsius to 55 degrees celsius.
• Non-operating –10 degrees celsius to 85 degrees celsius.
• Relative humidity, non-condensing 20% to 90%.
ORDERING INFORMATION
Cat. No.
6621
6621-P
Rating
600 Watts
600 Watts
6623-P
600 Watts
6631
6611-P
600 Watts
600VA
6613-P
600VA
6661-P1
480 Watts
6667-31
500 Watts 120V AC
6627
6629
5 Amps
1.5 Amps
Description
Single-Pole Incandescent Slide Dimmer
Single-Pole Incandescent Slide Dimmer
w/Preset ON/OFF Switch
3-Way Incandescent Slide Dimmer
w/Preset ON/OFF Switch
Illuminated Single-Pole Slide Dimmer
Single-Pole Magnetic Low-Voltage Slide Dimmer
w/Preset ON/OFF Switch
3-Way Magnetic Low-Voltage Slide Dimmer
w/Preset ON/OFF Switch
Single-Pole Magnetic Fluorescent Slide Dimmer
w/Preset ON/OFF Switch
Single-Pole and 3-Way Electronic Mark XTM/Philips EcotronTM
Fluorescent Slide Dimmer w/Preset ON/OFF Switch
Single-Pole Slide Fan Speed Control
Single-Pole Quiet Slide Fan Speed Control
Available in Brown (no dash), Ivory (-I), White (-W), Grey (-GY), and Black (-E). Illuminated versions available in Ivory and White only.
Leviton’s Limited Two-Year Warranty
This warranty gives you specific rights, and you may also have other rights, which vary in different states and countries. Leviton warrants to the original
consumer purchaser that this product is free of defects in materials and workmanship for 2 years from the purchase date. Leviton’s only obligation is
to correct such defects by repair or replacement, at its option, if within such 2 years the product is returned prepaid, with proof of purchase date, and
a description of the problem to the Leviton Manufacturing Co., Inc., ATTN: Quality Assurance Department, 59-25 Little Neck Pkwy., Little Neck, NY 113622591. This warranty does not cover labor for removal or reinstallation of the product and is void on any product installed improperly or in an improper
environment, overloaded, misused, opened, abused, or altered in any manner. There are no implied warranties of any kind, but if implied warranties
are required by the applicable jurisdiction, Leviton limits the duration of any implied warranty of fitness for use or merchantability to 2 years. Leviton
is not liable for incidental or consequential damages, including without limitation, loss of equipment use and lost sales or profits for breach of any
warranty on this product. Some jurisdictions may not allow exclusion of or limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the above exclusions or limitations may not even apply to you.
Leviton Mfg. Co., Inc. 59-25 Little Neck Pkwy • Little Neck, NY 11362 • Phone: (800) 323-8920 • Fax: (800) 832-9538
L26
Copyright © 1999 Leviton Manufacturing Co., Inc. All Rights Reserved
C-528K/C9-5M rp