MATERIALS AND FINISHES
for
Capital One
Tenant Finish Out
at
5444 Westheimer, Houston, Texas
GFF PROJECT NO. 14133.00
JULY 11, 2014
ISSUED FOR PRICING
Traci Webster IIDA
2808 Fairmount Street
Suite 300
Dallas, Texas 75201
214.303.1500/ Tel
214.303.1512/ Fax
www.gff.com
MEMORANDUM
Date:
Project No.:
Project Name:
Re:
07.11.14
14133.00
Capital One – Houston
th th
5444 Westheimer – 5 -7 Floors
Tenant Improvement Pricing Notes
Scope of Work
th
th
The preliminary pricing notes and plans provide an overview of the interior finish-out of the 5 to 7 5444
Westheimer, Houston TX. These notes and plans provide the general intent of the work. There may be
programming changes or unknown existing conditions which may cause these notes and plans to be
revised.
GENERAL NOTES:
1. Partition Types, UNO:
a. Typical Rooms: Provide 5/8” GWB on each side over 3-5/8” metal studs to 6” above ceiling
with sound attenuation batts and sealant.
b. Storage / File Rooms: Partitions shall be constructed to resist the passage of smoke, per IBC
508.2.2.1. Provide full height 5/8” GWB on both sides over 3-5/8” metal studs to deck with
sealant.
c. Mail Room / Commercial Ops Lock Box / Production Room: Provide 5/8” GWB on each side
over 3-5/8” metal studs extend to deck above with sound attenuation batts and sealant.
d. Conference Rooms 5402 / 5403 / 6402 / 7402: Provide 5/8” GWB on each side over 3-5/8”
metal studs extend to deck above with sound attenuation batts and sealant.
2. Door Types:
a. Typical Interior Doors: Wood veneer doors and interior aluminum storefront system (8’-6”
high), similar to Type II Flush Trim System Frame by Frameworks.
b. Storage Room: Wood veneer doors and metal frames with stainless steel armor plates on
each leaf. Provide hardware to comply with IBC 508.2.2.1.
c. Offices – All Glass System: All glass window system (8’-6” high), with 4” square bottom and
top rail at door and glass; ½” vision glass, clear tempered.
d. Conference Rooms - All Glass System: All glass window system, with 4” square bottom and
top rail at door and glass; ½” vision glass, clear tempered.
e. Conference Rooms – Gypsum Partition: Typical Interior Doors, no sidelights.
3. Finishes:
a. General: Refer to Finish Plans and Materials & Finishes 01900.
b. Typical Floor: Carpet tile, see Finish Plans and Materials & Finishes 01900.
c. Typical Wall: All partitions shall be painted with 2 coats of latex paint, satin finish. Assume
that there will be several field colors used, along with accent colors. Provide rubber base.
d. Typical Ceiling: Armstrong Dune ceiling tile (24x24x5/8 with beveled tegular edge) and 9/16”
ceiling grid (white) at 9’-0” AFF.
4. Electrical/Phone/Data:
a. General: Refer to Electrical Plans.
b. Reception Desk: Provide two electrical and two tele/data receptacles at each desk.
Coordinate installation of FA & security equipment at each desk. Provide additional empty
conduits as directed by owner.
P:\2014\14133 - CapOne Houston Westheimer\j-specs\01-pricing outline\PricingNotes_5444 Westheimer_140711.doc
Capital One – Houston
Tenant Improvement Pricing Notes
Scope of Work
July 11, 2014
Page 2 of 3
c.
Card Readers / Intercom System: Provide conduit and junction box at each location.
5. Lighting:
a. Refer to RCP and Light Fixture Schedule.
6. Sprinkler / Fire Alarm System:
a. Center and align sprinkler devices both ways in tiles.
b. Provide concealed escutcheon covers at all locations.
7. Blinds:
a. General: Reuse existing window blinds were possible. For locations with partial width blinds,
provide new full length blinds.
b. Conference Rooms 5402 / 5403 / 6402 / 7402: Provide recessed motorized black-out shades
at all exterior windows.
ROOM SPECIFIC NOTES:
8. Elevator Lobby:
a. Floor – Ceramic tile
b. Walls – Accent wall tile; stainless steel transoms above elevator door.
c. Ceiling – Gypsum ceiling, painted; height to be determined.
d. Doors - All-glass entry and doors
e. Note – Coordinate relocation / modification of existing elevator call button and hall lantern with
new finishes.
9. Conference Rooms – Small / Huddle:
a. Floor – Typical carpet.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Specialties – Provide wall mounted magnetic glass writing surface (72w X 48h) with pen rail &
tool kit by Clarus Glassboards
10. Conference Rooms - Medium:
a. Floor – Typical carpet.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Specialties – Provide wall mounted magnetic glass writing surface (96w X 48h) with pen rail &
tool kit by Clarus Glassboards.
11. Conference Rooms – Large VTC:
a. Floor – Typical carpet.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Millwork – Provide banquette seating between columns along exterior windows; plastic
laminate base and fabric wrapped seat and back cushions)
e. Specialties – Provide wall mounted magnetic glass writing surface (96w X 48h) with pen rail &
tool kit by Clarus Glassboards.
f. Specialties – Provide wall mounted acoustical wrapped fabric panel on the end walls (both
sides of room).
12. Coffee Niche – Small:
a. Floor – Refer to Finish Plan and Materials & Finishes 01900.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Millwork – Provide 3cm countertops with plastic laminate cabinet fronts.
e. Provide full-height tile backsplash above the millwork.
P:\2014\14133 - CapOne Houston Westheimer\j-specs\01-pricing outline\PricingNotes_5444 Westheimer_140711.doc
Capital One – Houston
Tenant Improvement Pricing Notes
Scope of Work
July 11, 2014
Page 3 of 3
f.
Appliances & Accessories - Provide appliances and accessories (ice water machine & trash
receptacles) Coffee maker provided and installed by Owner.
13. Coffee Niche – Large:
a. Floor – Refer to Finish Plan and Materials & Finishes 01900.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Millwork – Provide 3cm countertops with plastic laminate cabinet fronts.
e. Provide full-height tile backsplash above the millwork.
f. Appliances & Accessories - Provide appliances and accessories (ice water machine,
refrigerators, microwaves & trash receptacles) Coffee maker provided and installed by
Owner.
14. Break Room:
a. Floor – Refer to Finish Plan and Materials & Finishes 01900.
b. Walls – Typical wall.
c. Ceiling – Refer to RCP and Light Fixture Schedule.
d. Millwork – Provide 3cm countertops with plastic laminate cabinet fronts.
e. Millwork – Provide banquette seating; plastic laminate base and fabric wrapped seat and back
cushions)
f. Provide full-height tile backsplash above the millwork.
g. Appliances & Accessories - Provide appliances and accessories (ice water machine,
refrigerators, microwaves & trash receptacles) Coffee maker provided and installed by
Owner.
END OF NOTES
P:\2014\14133 - CapOne Houston Westheimer\j-specs\01-pricing outline\PricingNotes_5444 Westheimer_140711.doc
GFF PROJECT NO. 14133.00
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
SECTION 019000
MATERIALS and FINISHES
NOTE:
This list is an aid for understanding the intent of the materials and finishes used for the project.
This list is NOT comprehensive, with some materials and finishes listed in other sections of the
Project Manual and on the Drawings. Reference ALL Drawings and Project Manual for complete
information.
Reference locations are shown for informational purposes. Refer to the Drawings for the full
extent and exact locations of the finishes.
Basis-of-Design Product: Where a specific manufacturer's product is named, including make or
model number or other designation, it shall be used to establish the significant qualities related to
type, function, dimension, in-service performance, physical properties, appearance, and other
characteristics for purposes of evaluating comparable products of other named manufacturers.
DIV 01
GENERAL REQUIREMENTS
SEC 01810 Sustainable Design Requirements
A.
It is the intent of this Project to provide environmentally preferable products (EPP) to the
greatest extent possible. Provide products and materials that promote stewardship of the
earth's resources, promote good indoor environmental quality, and promote efficiencies in
operational performance. EPP's include products that have low VOC content; high recycled
content, and are manufactured, fabricated, or extracted within 500 miles of the construction
site.
B.
Urea-Formaldehyde Prohibition: Provide composite wood and agrifiber products having
no added urea-formaldehyde resins.
C.
Adhesives and Joint Sealants: Provide only products having lower volatile organic
compound (VOC) content than required by South Coast Air Quality Management District
Rule No.1168.
D.
Aerosol Adhesives: Provide only products having lower volatile organic compound (VOC)
content than required by GreenSeal GS-36.
E.
Paints and Coatings: Provide coatings that comply with the most stringent requirements
specified in the following:
1.
40 CFR 59, Subpart D--National Volatile Organic Compound Emission Standards
for Architectural Coatings.
2.
Ozone Transport Commission (OTC) Model Rule, Architectural, Industrial, and
Maintenance Coatings; www.otcair.org; specifically:
1) Opaque, Flat: 50 g/L, maximum.
2) Opaque, Nonflat: 150 g/L, maximum.
3) Opaque, High Gloss: 250 g/L, maximum.
4) Varnishes: 350 g/L, maximum.
DIV 05
METALS
SEC 055000 Metal Fabrications
A.
All metal fabrications that are exposed to view or to the exterior are to be constructed with
continuous welds, capped ends, etc. for a watertight, rust-preventing installation.
B.
Finish: Steel that is exposed to view is to have a surface preparation that provides a smooth
and continuous surface.
MATERIALS AND FINISHES 01900 - 1
GFF PROJECT NO. 14133.00
DIV 06
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
WOODS AND PLASTICS
SEC 064023 Interior Architectural Woodwork
A. WD-1 Type:
Qtr Cut Fumed Eucalyptus Wood Veneer
Manufacturer: Wood Gallery
Note:
Ref. Architects Sample
Reference:
Millwork & Wood Doors
B. B-2
Type:
Solid Stock
Finish:
Solid Stock wood painted PT-1
Size:
4” U.N.O. on Drawings
Reference:
Wood Base
C.
D.
E.
F.
Trash Grommet: Provide TM2C/SQ 8” square x 3” deep satin stainless steel, by Doug
Mockett & Company or approved equal.
Door/Drawer Pulls: Provide 6” DP3C-26D Tab Drawer Pull in Satin Chrome finish by Doug
Mockett & Company or approved equal.
Heavy Duty Standards & Brackets: Provide 82 Series Standard and Bracket system by
Knape & Vogt (or approved equal) in white. Provide bracket sized for shelf depth as
recommended by manufacturer.
Grommet: Provide two-part 3” metal grommet (GRN1) by Mockett & Company, in stain nickel
finish.
SEC 066400 Plastic Paneling
A. PL-1
Manufacturer: Abet Laminati
Style:
1086
Color:
Fiber
Finish:
Campione Gratutto
Reference:
Breakroom Coffee Niche & Copy Millwork
DIV 08
DOORS AND WINDOWS
SEC 081100 Standard Steel Doors and Frames
A. Finish: At interior, paint color to be selected by Architect.
SEC 081200 Interior Aluminum Door Frames
A. Non-rated aluminum door frames and sidelight frames at interior.
B. Style: Type II, Flush Trim System by Frameworks, Assa Abloy
C. Glazing: GL-1, see SEC 088000 Glass & Glazing
D. Finish: Clear Anodized Aluminum.
SEC 082110 Flush Wood Doors
A. All Doors: Custom Grade Heavy Duty performance, in accordance with WDMA I.S.1-A.
a. Wood Veneer Faced Doors: 5-ply unless otherwise indicated;
b. Non-Rated Solid Core and 20 Minute Rated Doors: Type particleboard core (PC),
c. Fire Rated Doors: Mineral core, Type FD, plies and faces as indicated above; with
core blocking as required to provide adequate anchorage of hardware without throughbolting
B. All wood doors shall be provided by the same manufacturer.
C. Refer to section 06400 Architectural Woodwork for wood species and finish.
SEC 08450 All Glass Entrances
A. Frame: Extruded 4” square full length top and bottom rails.
B. Door: Extruded 4” square full length door top and bottom rail.
C. Glazing: GL-1, see SEC 088000 Glass & Glazing
D. Finish: Satin Anodized.
MATERIALS AND FINISHES 01900 - 2
GFF PROJECT NO. 14133.00
E.
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
Accessories: Provide glazing gaskets, setting blocks, sealant, closure pieces as needed for
installation.
SEC 08710 Door Hardware
A. Set #1: Offices – All Glass System
a. Concelaed Overhead Closer w/Hold Open
b. Center Pivot – Top and Bottom
c. Lockset – Office Function
d. Floor Stop
B. Set #2: Conference Rooms – All Glass System
a. Concelaed Overhead Closer w/Hold Open
b. Center Pivot – Top and Bottom
c. Lockset – Passage Function
d. Floor Stop
C. Set #2A: Conference Rooms – Wood Door
a. Hinges
b. Lockset – Passage Function
c. Seals – Brush
d. Floor Stop
D. Set #3: Storage Rooms – Wood Door
a. Overhead Closer w/Hold Open
b. Hinges
c. Lockset – Store Room Function
d. Smoke Seals
e. Floor Stop
E. Set #4: Secure Corridors – Wood Doors
a. Overhead Closer
b. Hinges
c. Silencers
d. Lockset – Electrified – By Security Vendor; Coordinate with electrican & hardware
vendor
e. Transfer Hinge – By Security Vendor; Coordinate with electrican & hardware vendor
f. Power Supply – By Security Vendor; Coordinate with electrican & hardware vendor
g. Card Reader / Door Release – Coordinate with electrician, security vendor, & hardware
vendor
F. Set #4A: IDF / MDF Rooms – Metal Doors
a. Overhead Closer
b. Hinges
c. Silencers
d. Lockset – Electrified – By Security Vendor; Coordinate with electrican & hardware
vendor
e. Transfer Hinge – By Security Vendor; Coordinate with electrican & hardware vendor
f. Power Supply – By Security Vendor; Coordinate with electrican & hardware vendor
g. Card Reader / Door Release – Coordinate with electrician, security vendor, & hardware
vendor
G. Set #4B: Secure Rooms – Wood Doors
a. Overhead Closer
b. Hinges
c. Silencers
d. Lockset – Electrified – By Security Vendor; Coordinate with electrican & hardware
vendor
e. Transfer Hinge – By Security Vendor; Coordinate with electrican & hardware vendor
f. Power Supply – By Security Vendor; Coordinate with electrican & hardware vendor
g. Card Reader / Door Release – Coordinate with electrician, security vendor, & hardware
vendor
H. Set #5: Secure Entry / Lobby – All Glass System
MATERIALS AND FINISHES 01900 - 3
GFF PROJECT NO. 14133.00
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
a.
b.
c.
d.
e.
f.
I.
J.
K.
L.
M.
N.
O.
Concelaed Overhead Closer w/Hold Open
Center Pivot – Top and Bottom
Magnetic Lock – By Security Vendor; Coordinate with electrican & hardware vendor
Transfer Hinge – By Security Vendor; Coordinate with electrican & hardware vendor
Power Supply – By Security Vendor; Coordinate with electrican & hardware vendor
Card Reader / Door Release – Coordinate with electrician, security vendor, & hardware
vendor
Set #6: Mothers Room – Wood Door
a. Overhead Closer
b. Hinges
c. Lockset – Privacy Function w/Occupancy Indicator
d. Floor Stop
Set #7: Corridor – Double Egress Wood Door
a. Overhead Closer
b. Hinges
c. Panic Hardware w/Lever
d. Floor Stop
Set #8: Entry / Lobby – All Glass System
a. Concelaed Overhead Closer w/Hold Open
b. Center Pivot – Top and Bottom
c. Push / Pull Bar
d. Deadbolt at Bottom Rail
Lockset / Passage Set – Glass Door: Dorma Junior Office Classic
Lockset / Passage Set – Wood Door: Schlage Morties L Series
Finishes: To match 626 Satin Chromium Plated
Keyway: Coordinate all keying with owner’s master keying requirements.
SEC 088000 Glass & Glazing
A. GL-1: 1/2” vision glass, clear, tempered as required.
B. GL-2: 1/2” vision glass, clear, tempered as required.
C. GL-3: 1/4” vision glass, clear, tempered as required.
D. Glazing Channel: Provide glazing channels sized for thickness and height of glass of glass in
satin anodized finish; provide closure price at exposed ends.
DIV 09
FINISHES
SEC 092250 Interior Veneer Plaster
A. PL-1
Manufacturer: Southwest Progressive
Sample #:
41723.03
Reference:
Accent
B. Aged slaked-lime veneer plaster, two coat application over sheet gypsum or plaster base.
C. Verify substrate is flat smooth and surface is ready to receive work of this Section and has
received a Level 5 finish.
SEC 093000 Ceramic Tiling
A. T-1
Manufacturer:
Horizon Tile
Name:
Nr.21
Color:
Cemento Sand
Finish:
Natural
Size:
12” x 24”
Reference:
Floor Tile at Entry
B. WT-1 Manufacturer: Stone Source
Name:
Chiseled Limestone
Color:
Simena
Size:
6” x 24”
MATERIALS AND FINISHES 01900 - 4
GFF PROJECT NO. 14133.00
C.
D.
E.
F.
G.
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
Reference:
Wall Tile at Entry
Note:
Use factory edge at all exposed tile edges.
WT-2 Manufacturer: Stone Source
Name:
Raw Textured Limestone
Color:
Crème D’Orcia
Size:
8” x 24”
Reference:
Wall Tile at Entry
Note:
Use factory edge at all exposed tile edges.
WT-3 Manufacturer: Stone Source
Name:
Uon Uon - Ton Sur Ton
Color:
Bianco White Positive
Size:
8” x 48”
Reference:
Wall Tile at Breakroom & Coffee Niches
Note:
Use factory edge at all exposed tile edges.
Grout: General:
Sand/ Unsanded Latex-Modified Grout, sealed.
Restrooms:
Sand/ Unsanded Latex-Modified Grout, sealed
Showers:
Polymer-Modified Sanded Grout, sealed.
Galleys:
Sand/ Unsanded Latex-Modified Grout, sealed
Width:
1/16” for rectified tile; as recommended for unrectified tile.
Color:
TBD from manufacturer’s full range of colors
Trim: Provide prefabricated trim edge at all exposed edges of wall tile:
Manufacturer:
Schluter-QUADEC
Finish:
AT Satin Nickel Anodized Aluminum
Height:
Match thickness of tile
Note:
Reference drawings
Trim: Provide prefabricated trim edge at all exposed edges of floor tile:
Manufacturer:
Schluter-JOLLY
Finish:
AT Satin Nickel Anodized Aluminum
Height:
Match thickness of tile
Note:
Reference drawings
SEC 096513 Resilient Base and Accessories
A. B-1
Manufacturer: Johnsonite
Name:
Traditional Straight Toeless Base
Color:
50 White W
Size:
4” x 1/8” U.N.O. on Drawings
Reference:
General Rubber Base
B. Transition Strips: Homogeneous vinyl or rubber composition, in profile required to accept
flooring materials and compliant with ADA/TAS. Colors selected by Architect from
manufacturer’s full range of colors.
SEC 096519 Resilient Flooring
A. VCT-1 Manufacturer: Mannington
Name:
Touchstone
Color:
Flax 9143
Size:
12” X 12”
Reference:
Typical VCT
B. C-1
Manufacturer: Capri Cork
Name:
Mediterra Cork Planks
Color:
Jumble
Size:
4” X 24”
Reference:
Cork Plank Flooring at Breakroom & Coffee Niches
C. R-1
Manufacturer: Zandur
Name:
Smooth Surface
Color:
Shadow CR3061
Size:
12” X 24” X 2.5mm
MATERIALS AND FINISHES 01900 - 5
GFF PROJECT NO. 14133.00
CAPITAL ONE - HOUSTON
Reference:
SEC 096813 & 096816
A. CT-1
Manufacturer:
Name:
Color:
Type:
Size:
Installation:
Reference:
B. CT-2
Manufacturer:
Name:
Color:
Type:
Size:
Installation:
Reference:
C. CT-3
Manufacturer:
Name:
Color:
Type:
Size:
Installation:
Reference:
JULY 11 2014
ISSUED FOR PRICING
Rubber Tile Flooring in corridors
Tile and Sheet Carpeting
Interface
Reclaim
104147 Cottage Taupe
Carpet Tile
25cm x 1m
Ashlar
General Carpet Tile
Interface
Posh SH901
104120 Corfu
Carpet Tile
25cm x 1m
Ref. Finish Plans
Carpet at Offices & Conference Rooms
Interface
Posh PO801
104131 Amalfi
Carpet Tile
25cm x 1m
Ref. Finish Plans
Accent Carpet at Private Offices and Conference Rooms
SEC 097200 Wall Coverings
A. WC-1 Manufacturer: Knoll
Name:
Bollywood
Color:
Mandvi Beach WC1015
Width:
54”
Reference:
Typical Wallcovering & Wrapped Panels
B. Tackable Backer Board: Provide 1/2” tackable, impact resistant substrate.
SEC 099000 Painting
A. P-1
Manufacturer:
Name:
Color:
Finish:
B.
P-2
C.
P-3
D.
P-4
Sherwin Williams
Moderne White
SW6168
Eggshell
Flat at Ceilings
Reference:
General Paint
Note:
Low VOC
Manufacturer: Sherwin Williams
Name:
Useful Gray
Color:
SW7050
Finish:
Eggshell
Reference:
Accent Paint
Note:
Low VOC
Manufacturer: Sherwin Williams
Name:
Downing Stone
Color:
SW2821
Finish:
Eggshell
Reference:
Accent Paint
Note:
Low VOC
Manufacturer: Sherwin Williams
Name:
Homburg Gray
MATERIALS AND FINISHES 01900 - 6
GFF PROJECT NO. 14133.00
CAPITAL ONE - HOUSTON
Color:
Finish:
Reference:
Note:
JULY 11 2014
ISSUED FOR PRICING
SW7622
Eggshell
Accent Paint
Low VOC
DIV 10 SPECIALTIES
SEC 105220 Fire Extinguisher Cabinets
A. Cabinet: Semi-Recessed, 2-1/2” Rolled edge Cabinet with Solid Door and Recessed Handle,
White Baked Enamel Steel with Black Vertical Die-Cut Letters
B. Fire Extinguisher: Multi-purpose dry chemical; 5-lbs.
C. Verify depth of partition where new cabinet is being installed in existing partition.
DIV 11 EQUIPMENT
SEC 113100 Residential Appliances
A. MW
Manufacturer: Sharp Electronics Corporation (Substitutions Not Allowed)
Model:
R-22GT
Note:
Refer to plan for location and quantity
B. REF-A Refrigerator / Freezer (25.0 CF Side-by-Side)
Manufacturer: Whirlpool Corporation
Model:
WRS322FNAM
Note:
Refer to plan for location and quantity
C. REF-B Undercounter Refrigerator (5.5 CF ADA Compliant)
Manufacturer: Summit Appliance
Model:
AL752BSSHV
Note:
Refer to plan for location and quantity
D. I/W
Countertop Water Dispenser/Icemaker
Manufacturer: Hoshizabki
Model:
DCM-270 BAH
Note:
Refer to plan for location and quantity
DIV 12 FURNISHINGS
SEC 123662 Solid Surfacing Fabrications
A. QS-1
Manufacturer: Caesarstone
Name:
2370
Color:
Mocha
Finish:
Polished
Thickness:
2cm
Reference:
Breakroom & Coffee Niche countertops
B. QS-2
Manufacturer: Caesarstone
Name:
5000
Color:
London Grey
Finish:
Polished
Thickness:
2cm
Reference:
Conference room countertops
SEC 124940 Roller Shades
A. Roller Shade: Manual operating, chain drive, roller shades, ceiling mounted above finished
ceiling with white 3” closure panel. Provide mounting bracket for drum and drive. Closure
MATERIALS AND FINISHES 01900 - 7
GFF PROJECT NO. 14133.00
B.
C.
CAPITAL ONE - HOUSTON
JULY 11 2014
ISSUED FOR PRICING
panel to be continuous along entire length of window, provide custom corner pieces as
needed.
Roller and Black-out Shade: Double manual operating, chain drive, roller shade and black out
shade, ceiling mounted above finished ceiling with white 3” closure panel. Provide mounting
bracket for drum and drive. Closure panel to be continuous along entire length of window,
provide custom corner pieces as needed.
Fabric:
a. Roller Shade: Thermoveil Basket Weave 1500 Series; Gray 1313 by Mechoshade.
b. Room Darkening Blackout – Thermoveil Equinox 0200 Series, Smoke 0216, by
Mechoshade.
SEC 126100 Fixed Seating
A. FB-1
Manufacturer:
Name:
Color:
Application:
Reference:
B. FB-2
Manufacturer:
Name:
Color:
Reference:
Momentum Textiles
Estrella
Stone
54” Directional
Banquette Backs at Café
Maharam
Lariat 440401
007 Oyster
Banquette Seats at Café
END OF SECTION 019000
MATERIALS AND FINISHES 01900 - 8
LIGHT FIXTURE SCHEDULE
Project
Location
Type
C
HOUSTON, TX
Manufacturer
Catalog Number
Description
Lamp
Volt
Finish
A
Finelite
HPR-A-DCO-1T5HO-VOLTAGE-SC-CXX TBAR-PS
FLUORESCENT RECESSED 2X4 FIXTURE WITH ANGLED
ACRYLIC LENS DIFFUSER, AND INTEGRAL ELECTRONIC
BALLAST
54W 3500K T5HO
PER EE
WHITE
B
Eureka Lighting
3132-LENGTH-SOURCE-VOLTAGE-FINISH-CHR3980
LED LINEAR WALL-MOUNTED FIXTURE WITH INTEGRAL LED
DRIVER
TBD
PER EE
C
Zumtobel
S5D6308H-U-6313HR-MC
COMPACT FLUORESCENT RECESSED DOWNLIGHT WITH 6
INCH. APERTURE, MATTE CLEAR ALZAK REFLECTOR, AND
INTEGRAL ELECTRONIC BALLAST
32W 3500K CFL
TRIPLE T GX24Q-3
PER EE
Finelite
HP-4D-12'-HO-3500K-VOLTAGE-FA-SC-CEILING
TYPE
LED SUSPENDED PENDANT WITH 4 INCH. APERTURE FROST
WHITE SNAP-IN LENS, EXTRUDED ALUMINUM HOUSING,
DIECAST ALUMINUM ENDCAP, AND INTEGRAL LED DRIVER
112W 3500K LED
INTEGRAL
PER EE
WHITE
D-12
Note
PER
ARCHITECT TO IDENTIFY FIXTURE HEIGHT AND FINISH.
ARCHITECT
E
Studio Italia Design SOAP-SO-SP
DECORATIVE SUSPENDED PENDANT
60W T4 G9BASE
PER EE
TBD
F
Eureka Lighting
4800-36-LED-40-30-VOLTAGE-DIMMING OPTIONAC-CABLE LENGTH-RC-WHM-WHM
LED SUSPENDED PENDANT WITH 36 INCH. DIAMETER RING, 4
INCH. TALL, ROUND CANOPY WITH INTEGRATED DRIVER, AND
MATTE WHITE FINISH
40W 3000K LED
INTEGRAL
PER EE
WHITE
G8
Finelite
HP-4R-8'-SO-3500K-VOLTAGE-SC-MOUNTING
LED LINEAR RECESSED WITH 4 INCH. APERTURE FROST
WHITE SNAP-IN LENS, EXTRUDED ALUMINUM HOUSING,
DIECAST ALUMINUM ENDCAP, AND INTEGRAL LED DRIVER
37W 3500K LED
INTEGRAL
PER EE
WHITE
G8-D
Finelite
HP-4R-8'-SO-3500K-VOLTAGE-SC-MOUNTINGDIMMING
LED LINEAR RECESSED WITH 4 INCH. APERTURE FROST
WHITE SNAP-IN LENS, EXTRUDED ALUMINUM HOUSING,
DIECAST ALUMINUM ENDCAP, AND INTEGRAL LED DRIVER
37W 3500K LED
INTEGRAL
PER EE
WHITE
H1
Luceplan
1D710P000002-1D71/2000502
FLUORESCENT SUSPENDED FIXTURE WITH SOUND
ABSORBENT PANEL UPHOLSTERED IN WHITE FABRIC, AND
INTEGRAL LED DRIVER
22WFC9T5 2GX13 +
40W FC12T52GX13
PER EE
WHITE
H2
Luceplan
1D710P1L0002-1D71/20L0502
FLUORESCENT SUSPENDED FIXTURE WITH SOUND
ABSORBENT PANEL UPHOLSTERED IN WHITE FABRIC, AND
INTEGRAL LED DRIVER
22WFC9T5 2GX13 +
40W FC12T52GX13
PER EE
WHITE
J4
Engineered
444W1IW-TB-DMXX-W-3500K
Lighting Productes
LED RECESSED VIDEO CONFERENCE FIXTURE WITH
ASYMMETRIC DISTRIBUTION, AND INTEGRAL DIMMABLE LED
DRIVER
43W 3500K LED
INTEGRAL
PER EE
WHITE
K
Zumtobel
BS6WHCFL-32W-U
COMPACT FLUORESCENT RECESSED WALLWASHER WITH 6
INCH. APERTURE, MATTE CLEAR ALZAK REFLECTOR, AND
INTEGRAL ELECTRONIC BALLAST
32W 3500K CFL
TRIPLE T GX24Q-3
PER EE
Zumtobel
BS6WHCFL-32W-GX24Q3-CM-N
TRIM
Zumtobel
BS6WHCFL-32W-LUTRON
COMPACT FLUORESCENT RECESSED WALLWASHER WITH 6
INCH. APERTURE, MATTE CLEAR ALZAK REFLECTOR, AND
INTEGRAL DIMMING ELECTRONIC BALLAST
32W 3500K CFL
TRIPLE T GX24Q-3
PER EE
AV CONSULTANT TO IDENTIFY DIMMING PROTOCOL FOR LUTRON
DIMMING BALLAST.
Zumtobel
BS6WHCFL-32W-GX24Q3-CM-N
TRIM
LF Illumination
MF32BN-T-11L-9030-M-GD-DXX-U-FINISH
LED RECESSED MULTIPLES FIIXTURE WITH INTEGRAL
DIMMABLE DRIVER
(2)11W 3000K LED
INTEGRAL
PER EE
AV CONSULTANT TO IDENTIFY DIMMING PROTOCOL FOR LUTRON
DIMMING BALLAST.
M8
Finelite
HPW-LED-8'-FR-LED-3500K-VOLTAGE-SCMOUNTING
LED LINEAR RECESSED WALLWASHER WITH ASYMMETRICAL
DISTRIBUTION, 6 INCH. APERTURE, 8 FT. LENGTH, AND
INTEGRAL DRIVER
75W 3500K LED
INTEGRAL
PER EE
M8-D
Finelite
HPW-LED-8'-FR-LED-3500K-VOLTAGE-SCMOUNTING-LUTRON DRIVER
LED LINEAR RECESSED WALLWASHER WITH ASYMMETRICAL
DISTRIBUTION, 6 INCH. APERTURE, 8 FT. LENGTH, AND
INTEGRAL DRIVER
75W 3500K LED
INTEGRAL
PER EE
N
Neidhardt
FLEX COLLECTION-PENDANT A19
LED SUSPENDED DECORATIVE PENDANT WITH 285 LUMENS
OUTPUT, AND INTEGRAL LED DRIVER
3300K LED INTEGRAL
PER EE
PER
ARCHITECT TO IDENTIFY SHADE COLOR AND METAL FINISH.
ARCHITECT
O
Neidhardt
FLEX G40
LED SUSPENDED DECORATIVE PENDANT WITH 243 LUMENS
OUTPUT, AND INTEGRAL LED DRIVER
3100K LED INTEGRAL
PER EE
PER
ARCHITECT TO IDENTIFY SHADE COLOR AND METAL FINISH.
ARCHITECT
P
Luceplan
1D7909S005-FINISH
COMPACT FLUORESCENT SUSPENDED DECORATIVE PENDANT (3)SYLVANIACF23EL/
WITH 35 INCH. DIAMETER, 17.7 INCH. HEIGHT, FABRIC SHADE
MICRO/830/ECO
WITH SOUND ABSORPTION
PER EE
PER
ARCHITECT TO IDENTIFY SHADE COLOR.
ARCHITECT
Q
Targetti
NUDA-17.8-2/32W/CF GX24Q3-120-277V-COLORSHADE
COMPACT FLUORESCENT SUSPENDED DECORATIVE PENDANT (2)32W 3500K CFL
WITH 18 INCH. DIAMETER, 7 INCH. HEIGHT, POLYURETHANE
TRIPLE GX24Q-3
MATTE FINISH OUTER SHADE, BLOWN GLASS OPAL DIFFUSER,
SPUN ALUMINUM MATTE FINISH INNER SHADE
PER EE
PER
ARCHITECT TO IDENTIFY INNER AND OUTER SHADE COLORS.
ARCHITECT
K-D
L
LOCATION: RECEPTION DESK, PHONE BOOTHS
IDENTIFY DIMMING PROTOCAL/DIMMING DRIVER
AV CONSULTANT TO IDENTIFY DIMMING PROTOCOL FOR LUTRON
DIMMING DRIVER.
AV CONSULTANT TO IDENTIFY DIMMING PROTOCOL FOR LUTRON
DIMMING BALLAST.
BUY AMERICAN ACT OF 2009 COMPLIANT
High Performance Recessed (HPR-LED) 2x4
FIXTURE
TYPE A
Date
try B
us
st
e
In
d
FINELITE
10
Year
Warranty
®
HPR-LED Collection
2011 IES Progress
Report Selection
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
Qualified Luminaire
Project
HPR-LED
Type
Comments
HPR-A (Angled)
HPR-F (Flat)
HPR-LED uses patent pending technology
DESCRIPTION
HPR-LED is a highly effective recessed luminaire delivering excellent visual comfort and
outstanding performance for offices, schools, healthcare, and retail applications. Advanced
optical designs make HPR-LED a powerful solution for low-ceiling applications and eliminate
the shadows common to other LED recessed products. HPR-LED RoHS compliant.
GLARE-FREE ILLUMINATION:
100% SERVICEABLE FROM BELOW:
THERMAL MANAGEMENT:
A glare-free experience is attained with midpowered LEDs properly distributed and paired
with a precise diffuser to eliminate pixilation.
The light engine and driver can be easily
changed from below ceiling – and it’s simple
to install.
Mid-powered LEDs allow heat to be fully
dissipated without the need for additional
heat sinks.
ORDERING GUIDE
Sample Number: HPR - A - 2x4- DCO - LED-SO - 4000K - 277V - SC - C1 - OBO
HPR
HO = High Output 4880 lumens (3000K), 5585 lumens (3500K), 5928 lumens (4000K)
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data.
Form CTK0054. 03/14
* SO = Standard Output 3403 lumens (3000K), 3786 lumens (3500K), 3721 lumens (4000K)
VHO = Very High Output 6398 lumens (3000K), 6869 lumens (3500K), 7291 lumens (4000K)
© 2014 FINELITE, INC. ALL RIGHTS RESERVED.
Finelite Series HPR
Luminaire Styles (A-Angled, F-Flat)
Size (2x4)
Center Optic (DCO-Diffuse, SCO-Slotted, RCO-Round)
Light Engine* (LED-SO, LED-HO, LED-VHO)
LED Color Temperature (3000K, 3500K, 4000K)
Voltage (120V, 277V)
Circuiting (SC-Single Circuit)
Mounting (C1-1" T-Bar, C2-9/16" T-Bar, C3-Screw Slot, DW-Drywall Kit, SM-Surface Mount)
Integrated Sensors (OBD-Daylight, OBO-Occupancy, OBB-Both)
FIXTURE TYPE B
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
SPEC-5
Open Recessed
Downlight and Wallwasher
Vertical Compact Fluorescent
(1) 26W or (1) 32W Triple Tube
6"
45° cutoff
Applications: A vertical CFL fixture
online
Find it Fast
is the ideal choice for use in offices and
lobbies which demand a low brightness
aperture with high lumen output. The
6" aperture fixture is designed with
45° cutoff for excellent glare control.
Available in two wattages with a standard
electronic ballast.
118
Type:________________________________________
FIXTURE TYPE C
ARCHITECTURAL LIGHTING ASSOCIATES
Project:______________________________________
PROJECT: PROJECT C - HOUSTON, TX
__________________________________________
ORDERING NOTE: Complete unit consists of rough-in and trim section. Indicate ballast/voltage and desired options.
6313_____
S5D_____
BALLAST/VOLTAGE
ROUGH-IN
S5D6313H
(1) 26W Triple Tube
S5D6308H
(1) 32W Triple Tube
U
S3
LH1
LH2
LE1
LE2
LT1
AM1
AM2
AX1
AX2
TRIM
Universal 120V/277V
Dedicated 347V
LUTRON HiLume® (1%) 120V
LUTRON HiLume (1%) 277V
LUTRON EcoSystem® (5%) 120V
LUTRON EcoSystem® (5%) 277V
LUTRON TuWire® (5%) 120V
ADVANCE® MARK VII® (5%) 120V
ADVANCE MARK VII (5%) 277V
ADVANCE® MARK X® (5%) 120V
ADVANCE MARK X (5%) 277V
TRIM FINISH
6313HR Downlight
Reflector
6313HW Wallwasher
Reflector
6313HK Corner
Wallwasher
OPTICS
C
Clear Specular
Reflector
MC Matte Clear
Alzak® Reflector
F*
W
9930
9952
9956
NOTE: Add “E” to end
of reflector description
for standby fixture.
E4
___
Fusing
White painted reflector flange
Set of two 27" C-channel mounting bars
Set of two 52" C-channel mounting bars
Set of two 28" 10 ga. one piece
universal mounting bars
Standby Battery Pack 120/277v
Deco Trims (See p. S5-20)
(for downlight only)
E4 is not available with 347V.
*Fusing not available with 347V.
11 1/2"
11 3/16"
11 3/16"
9 3/16"
6 1/4"
6 3/4"
6 1/4"
6 3/4"
Downlight
C
Wallwasher
7 1/4"
UL
®
7 1/4"
(Ceiling Opening = 6 3/4")
3. Mounting Bracket - Adjustable
butterfly mounting brackets allow
for a vertical adjustment of 2 7/8"
and accept one piece universal or
C-channel mounting bars (ordered
as an optional accessory).
US
LISTED
Suitable for damp locations
Fixtures with standby battery packs
are rated for dry locations only
Approved for thru-wiring
Above ceiling access not required
Thermally protected
IBEW Union Made
Alzak®is a registered trademark of the
Aluminum Company of America.
1. Yoke Assembly - 18 gauge steel
yoke assembly is corrosion protected
and fixed to mounting pan.
2. Plaster Frame - 20 gauge
galvanized, die-formed plaster frame
has a fixed throat depth of 1".
4. Splice Compartment - 18 gauge
galvanized splice compartment is
U.L. listed for thru-wiring (4 in and
4 out at 90˚C) and has 7/8" and
1 1/8" knockouts. Ground wire is
supplied. Splice compartment is
accessible from below ceiling. Splice
compartment cover is attached to the
yoke assembly by contractor.
5. Standby Battery Pack - IOTA
I-42, mounted on splice compartment
cover. An integral test light/switch,
supplied, is accessible and visible
through reflector aperture. Operates
on 120v or 277v, 60Hz only.
Zumtobel Lighting, Inc. ©2014
3300 Route 9W
Highland, NY 12528-2630
845-691-6262
800-448-4131
zli.us@zumtobel.com
03/28/14
www.zumtobel.us
6. Reflector - One piece spun
aluminum reflector with 1/2" flat
flange with low iridescence, specular
clad finish. Clear specular and matte
clear Alzak® finishes are available.
A white painted reflector flange is
also available. The reflector is secured
to the yoke assembly by 2 captive
screws. This reflector has been
designed for 45° cutoff to lamp and
lamp image.
accommodate multiple lamp wattages
and is preset at factory.
7. Wallwasher Reflector - A
hydroformed aluminum kicker plate
is mounted to the main reflector and
available in three specific configurations for wall illumination. Reflector
assembly fully rotatable from below
ceiling ensuring proper reflector
alignment.
NOTE: National or municipal codes
must be followed regarding set back
of thermal insulating material from
fixture. As a guideline, any insulation
materials must be held away from the
fixture by a minimum of 3". Fixtures
are not designed for direct contact
with thermal insulation.
8. Lamp/Socket - One 26W or 32W
triple tube compact fluorescent lamp
with a GX24q-3 socket. Lamp supplied
by others. Socket is adjustable to
In a continuing effort to offer the best product possible, we
reserve the right to change, without notice, specifications or
materials. Technical specification sheets that appear on
www.zumtobel.us are the most recent version and supersede all
other versions that exist in any other printed or electronic form.
9. Ballast - One (1) lamp, thermally
protected Class P electronic ballast is
supplied.
EcoSystem ballast is wired to E1 & E2
(not dim hot) unless otherwise specified.
10. Weight - Housing: 4.5 lbs.
Trim: Downlight - 0.6 lbs.;
Wallwasher - 0.8 lbs.
BUY AMERICAN ACT OF 2009 COMPLIANT
try B
us
High Performance 4” Aperture (HP-4) - Direct
FIXTURE
TYPE D12
Date
20I2
st
e
In
d
FINELITE
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
10
Year
Project
Warranty
HP-4-LED
Type
Comments
DESCRIPTION
High Performance 4” aperture direct pendant (HP-4 D) is a patent pending, linear LED luminaire for
offices, schools, retail and healthcare facilities. Advanced optical designs and mid-powered LEDs
deliver an efficient, long-lasting luminaire free of glare and socket shadows for single and continuous
lighting applications. HP-4 D is RoHS compliant.
4”
4”
DIMENSIONS & LIGHT ENGINE:
FLEXIBLE MOUNTING:
SEAMLESS ILLUMINATION:
A glare-free experience is attained with midpowered LEDs properly distributed and paired
with a precise diffuser to eliminate pixilation.
The Flexible Mounting Bracket (FM) adjusts
the suspension point along the length of
the luminaire to accommodate existing
architecture.
The optical design features seamless lenses up to
12’ in length and eliminates socket shadows at
joints and corners.
ORDERING GUIDE
Sample Number: HP-4 D - 32’ - SO - 3500K - 120V - FA - SC - C1
© 2013 FINELITE, INC. ALL RIGHTS RESERVED.
HP-4 D
Finelite Series HP-4 D
Size (4’, 8’, 12’ multiples standard)
Light Engine (SO - Standard Output, HO - High Output)
LED Color Temperature (3000K, 3500K, 4000K)
Voltage (120, 277V)
Mounting (FA, FM-Flexible Mounting)
Circuiting (SC-Single Circuit, MC-Multi-Circuit)
Ceiling Type (C1-1" T-Bar, C2-9/16" T-Bar, C3-Screw Slot, C4-Hard Ceiling)
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data.
Form CTK0073. 10/13
Patent Pending
FIXTURE TYPE E
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
FIXTURE TYPE F
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
BUY AMERICAN ACT OF 2009 COMPLIANT
try B
us
st
e
In
d
FINELITE
High Performance 4” Aperture (HP-4) - Recessed
FIXTURE
TYPE G8
Date
20I2
10
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
Year
Project
Warranty
HP-4-LED
Type
Comments
DESCRIPTION
High Performance 4” aperture recessed (HP-4 R) is a patent pending linear LED luminaire for offices,
schools, retail and healthcare facilities. HP-4 R is the first recessed linear LED luminaire to feature
On-Grid™ mounting for standard lengths, making installation quick and easy. Advanced optical
designs and mid-powered LEDs deliver an efficient, long-lasting luminaire free of glare and socket
shadows for continuous lighting applications. HP-4 R accommodates grid and drywall ceilings. 90º
corners are available for ceiling and wall-to-ceiling applications. HP-4 R is RoHS compliant.
90° Wall to Ceiling
4”
4”
Flush Diffuser
DIMENSIONS & LIGHT ENGINE:
MITERED ANGLES:
SEAMLESS ILLUMINATION:
A glare-free experience is attained with mid-powered LEDs
properly distributed and paired with a precise diffuser to
eliminate pixilation.
Illuminated 90º corners and wall-to-ceiling
configuration are seamless without socket
shadows. Custom angles are available.
Contact factory.
The optical design features seamless lenses up
to 12’ in length and eliminates socket shadows
at joints and corners.
ORDERING GUIDE
Sample Number: HP-4 R - 32’ - S0 - 3500K - 120V - SC - C1
HP-4 R
Patent Pending
Due to continuing product improvements, Finelite reserves the right to change specifications without notice. Please visit www.finelite.com for most current data.
CTK0075. 2/14
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
© 2014 FINELITE, INC. ALL RIGHTS RESERVED. Form
Finelite Series HP-4 R
Size (4’, 8’, 12’ multiples standard)
Light Engine (SO - Standard Output, HO - High Output)
LED Color Temperature (3000K, 3500K, 4000K)
Voltage (120, 277V)
Circuiting (SC-Single Circuit, MC-Multi-Circuit)
Mounting (C1-1" T-Bar, C2-9/16" T-Bar, C3-Screw Slot, C3F-Flush Screw Slot, VF-Visible Flange, C2T-9/16" Tegular, C1T-1" Tegular, SF-Spackle Flange, TZ6-Tech Zone 6”)
FIXTURE TYPE H1
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
PÉTALE
design Odile Decq, 2011
Type:
Suspension
Lamps:
Dimmable 21W center LED or 2 x T5
with LED low power strip perimeter for accent
Product use:
Indoor
Materials:
Sound absorbing panel
Colors:
White elastic tissue
Description:
Light as a suspended petal, white as the subdued lighting
and with a softness that enhances it. A suspension lamp
with an organic form which conceals the magic of silence
within: the body consists of a sound-absorbent panel
upholstered in white fabric
D71P1L
47.2”
120 cm
Reference code: Structure
D71P1L 1D710P1L0002
2.3”
6 cm
Certification
white
60.8”
154,5 cm
+
Optic
D71/2L 1D71/20L0502
D71/4L 1D71/40L0502
Lamp
D71/2L (on/off)
+ low power LEDs
22W
FC9 T5
2GX13
(120-277V~)
+
40W
FC12 T5
2GX13
(120-277V~)
+
18W LED(*)
(*)with LED low
power strip
on inside for light accent
www.luceplan.com
D71/4L dimmable
DLP1.1 + low power LEDs
LED 21W
+
LED strip 18W
FIXTURE TYPE J4
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
IW & IWTB SERIES
th
Now wi ns!
tio
LED op
RECESSED Indirect for Vertical Illumination
For Drywall & T-Bar
T-Bar Fixture
LED Drywall Fixture
Ideal placement is 24˝ to 36˝
from the front edge of fixture
to the surface you are lighting,
for 8´ to 12´ ceilings.
System
Recessed indirect LED and fluorescent fixtures with asymmetric wash of light to provide vertical illumination in difficult
applications such as mirrored surfaces and video conference key speaker where a shielded lamp is critical. The formed
reflector provides even, unscalloped illumination with no glare.
BASYS™
Recessed
Square
Non-IC
Wallwasher
Horizontal
32W
GX24Q-3
FIXTURE TYPE K,K-D
Type:
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
Project:
Compact
Fluorescent
BASYS HOUSING
BS6WHCFL
32W
FIXTURE
WATTAGE
BASYS
Recessed Square
6" Aperture
Non-IC Wallwasher
BALLAST/VOLTAGE
32W
OPTIONS
U
Universal 120V/277V
EM*
Standby Battery Pack - Standard Lumen
S3
Dedicated 347V
EH
Standby Battery Pack - High Lumen
LH1 LUTRON HiLume (1%) 120V
F**
Fusing
LH2 LUTRON HiLume (1%) 277V
CP
Chicago Plenum
®
LE1 LUTRON EcoSystem (5%) 120V
LE2 LUTRON EcoSystem® (5%) 277V
LT1 LUTRON TuWire (5%) 120V
* EM is not available with 347V
AM1 ADVANCE® MARK VII® (5%) 120V
** Fusing not available with 347V
AM2 ADVANCE MARK VII (5%) 277V
AX1 ADVANCE® MARK X® (5%) 120V
AX2 ADVANCE MARK X (5%) 277V
BASYS TRIM
BS6WHCFL
32W
FIXTURE
WATTAGE
BASYS
Recessed Square
6" Aperture
Non-IC Wallwasher
32W
GX24Q3
BASE
GX24Q3
TRIM FINISH
FLANGE
CB Clear Brushed
N Natural
CM Clear Matte
W White
WH White Matte
C Custom
C
OPTIONS
E Standby Battery Pack
Custom
BASYS MOUNTING
ACCESSORIES
9930
2 – 27" C-Channel Mounting Bars
9952
2 – 52" C-Channel Mounting Bars
9956
2 – 28" 10-Gauge, One-Piece Universal Mounting Bars
Advance and Mark X are registered trademarks of Philips Electronics North America Corporation
Zumtobel Lighting, Inc. ©2014
3300 Route 9W
Highland, NY 12528-2630
845-691-6262
800-448-4131
zli.us@zumtobel.com
D00362TS
www.zumtobel.us
03/24/14
In a continuing effort to offer the best product possible
we reserve the right to change, without notice,
specifications or materials. Technical specification sheets
that appear on www.zumtobel.us are the most recent
version and supersede all other versions that exist in
any other printed or electronic form.
6"
online
Find it Fast
372
MULTIFORMS - MF300 Series
RECESSED ADJUSTABLE STRAIGHT APERTURE 2-LIGHT
TRIMMED
PROJECT
TYPE
SMALL
CATALOG NUMBER
FIXTURE TYPE L
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
13.40” (340)
1
5.42”
(138)
6.42”
(163)
2
LED
360º+
Rotation
Double
Gimbal
40º Tilt
40º Tilt
1
Accommodates 1/2” through 1.0”
Ceiling Thickness
40º 40º
4.00” (102)
2
Deep
Trim Sleeve
9.50” (241)
8.00” (203)
Conceals inner
components from view
5.50” 4.00”
(140) (102)
8.22”
(209)
Shown with regressed yoke lamp holder (GD)
to accommodate snoot accessory
10.92”
(277)
3
Optional
Trim Mounted
Double Gimbal
(TD) Outer gimbal ring may be mounted directly
to the trim sleeve wall eliminating the need for a yoke.
Integral Power Supplies
& Wiring Compartment
ELECTRICAL
• Field-replaceable integral LED driver
• Electrical wiring compartment integrated into housing construction
• Thermal protection
• Easy maintenance access through ceiling opening
• Rated for through-branch wiring
• Dimmable
DESCRIPTION
• Two light recessed accent / downlight - small size
• All steel 18GA construction with powder coat finish
• .75” Trim flange with 4” x 8” open aperture
• Trim flange removable for maintenance
• Vent holes for cooler operating temperature
• Trim features deep sleeve to conceal inner components
• Ceiling Cut-Out - 5.12” x 9.12”
MOUNTING
• Butterfly brackets for commercial installation in drywall, wood, stone,
acoustic tile, or other ceiling types
• Continuously variable plate adjusts for 1/2” through 1.0” ceilings
LAMPS
• Field-replaceable integral LED module
• Field-changeable optic
• 11W / 950lm, 80CRI / 3000K
• 16W / 1100lm, 80CRI / 3000K
• 23W / 1450lm, 80CRI / 3000K
• Accepts up to 2 or more optical accessories
• Double gimbal lamp holder with up to 40º x 40º tilt aiming
• Yoke with lockable 360º+ rotation
• Flush yoke, regressed yoke, adjusting retractable yoke, or trim
mounted double gimbal option
LABELS
• Suitable for damp location
10 YEAR
WARRANTY
Limited
ORDERING INFO
SERIES
WATTAGE
MF32BN-T
11L 11W LED 8027 80CRI / 2700K N Narrow
950 lm
8030 80CRI / 3000K M Medium
nom.
8035 80CRI / 3500K W Wide
8040 80CRI / 4000K
16L 16W LED 9027 90CRI / 2700K
1100 lm 9030 90CRI / 3000K
nom.
9727 97CRI / 2700K
9730 97CRI / 3000K
23L 23W LED
1450 lm
nom.
MULTIFORMS
MF300 Series
Recessed 2-Light
Straight Aperture
Adjustable Accent
Trimmed Fixture
New Construction
Housing
CRI / COLOR
BEAM
C
LAMP ASSEMBLY
DRIVER
VOLTAGE
TD Trim Mounted
Double Gimbal
YD Double Gimbal Flush
to Ceiling Line
GD Regressed Double
Gimbal*
RD Retractable Double
Gimbal
LD LED Driver
D1 Phase Dim.
120V
D2 0-10V Dim.
120-277V
D3 Lutron
Hi-Lume
120-277V
D4 Lutron
Eco-System
120-277V
1 120V
BB Black
CP Chicago
U 120-277V WW White
Plenum
3 347V*
WB White Trim / EM Emergency
Black Interior
Relay
SS Silver
SB Silver Trim /
Black Interior
XX Custom
* Required to enable flush
appearance with snoot
accessory.
FINISH
®
US
OPTIONS
* Consult
factory
MF32BN-T
Ordering Example: MF32BN-T-16L-8027-N-YD-D1-1-BB-CP
©2013 LF ILLUMINATION LLC
HEADQUARTERS
Telephone: 818-885-1335
We reserve the right to change or
9200 Deering Avenue
Toll Free: 855-885-1335
withdraw specifications without prior notice.
Chatsworth CA 91311
Fax: 818-576-1335
www.lfillumination.com
rev: 102513
BUY AMERICAN ACT OF 2009 COMPLIANT
High Performance Wall (HPW-LED)
FIXTURE
TYPE M8, M8D
Date
try B
us
st
e
In
d
FINELITE
HPR-LED Collection
2011 IES Progress
Report Selection
10
Year
Warranty
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
Project
HPR-LED
Type
Comments
DESCRIPTION
HPW-LED is a high performance recessed asymmetric LED wall wash that delivers excellent
visual comfort and uniform vertical illumination for school and office applications.
SHIELDING:
THERMAL MANAGEMENT:
100% SERVICEABLE FROM BELOW:
HPW-LED is standard with a frosted lens for
glare-free lighting and a smooth distribution on
the vertical surface. All lenses are UV-stabilized
and impact resistant virgin acrylic.
Mid-powered LEDs allow heat to be fully dissipated
without the need for additional heat sinks.
The light engine and driver can be easily
changed from below ceiling – and they are
simple to install.
ORDERING GUIDE
Sample Number: HPW-LED - 4’- FR - LED - 4000K - 277 - SC - C1
Finelite Series HPW-LED
Length (2', 4', or 8')
Lens Optic (FR-Frosted)
Light Engine (LED)
LED Color Temperature (3000K, 3500K, 4000K)
Driver (120, 277V)
Circuiting (SC-Single Circuit)
Mounting (C1-1" T-Bar, C2-9/16" T-Bar, C3-Screw Slot, DW-Drywall Kit)
Form CTK0072.03/13
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
© 2012 FINELITE, INC. ALL RIGHTS RESERVED.
HPW-LED
FIXTURE TYPE N
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
FIXTURE TYPE O
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
FIXTURE TYPE P
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX
FIXTURE TYPE Q
ARCHITECTURAL LIGHTING ASSOCIATES
PROJECT: PROJECT C - HOUSTON, TX