SEMI AUTOMATIC POLYPROPYLENE
STRAPPING MACHINE
TP-201
TP-202
TP-203
TP-202L
TP-201CE
TP-202CE
TP-203CE
TP-202LCE
TP-201Y
TP-201YS
OPERATION MANUAL
&
SPARE PARTS LIST
Original Instruction
READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT
PART I
CONTENTS
1. Safety Instructions................................................................................. 1
2. Construction and Units.......................................................................... 2
3. General Safety Remarks........................................................................ 3
4. Machine Information............................................................................. 5
5. Machine and Operating Element......................................................... 10
6. Operating the Machine.........................................................................11
7. Adjustments ........................................................................................ 12
8. Maintenance & Lubrication ................................................................ 14
9. Troubleshooting Guide........................................................................ 16
10. Wiring Diagram .................................................................................. 19
1. Safety Instructions
THIS MANUAL GIVES YOU INFORMATION ON SAFETY INSTRUCTIONS,
SPECIFICATIONS, OPERATION AND MAINTENANCE OF STRAPPING
MACHINES.
BEFORE OPERATING OR SERVICING THE MACHINE, PLEASE REVIEW THE
ENTIRE MANUAL AND FOLLOW THE SAFETY INSTRUCTIONS CAREFULLY.
(1) Before Operating
a. Verify that the power line voltage is correct.
b. The machine must be properly grounded to avoid a shock hazard. All wiring must be
in accordance with local wiring standards.
c. The strapping machine can only be operated with polypropylene (P.P.) strapping; do
not use polyester (PET) strapping or polyethylene (PE) cord strap.
(2) During Operation
a. The weight of the package cannot exceed 100 kg (220 lbs).
b. The size of the package should not be less than 80mm (width) × 20mm (high) (3.16＂
×0.79＂).
c. Check if the machine emits any smokes or unusual sound when it is running.
(3) After operating
a. Remove dust and dirt from the unit; pay particular attention to the interior of the arch.
b. Turn off the power when the machine is not in use.
(4) Signs
Caution!
Electric Shock Hazard
(5) Maintenance
a. Turn off the power before removing either of the top covers.
b. Use the correct tools and parts to repair the machine.
c. The heater tongue is very hot; do not touch it.
-1-
Caution!
Hot!
Do not touch!
(6) Storage
a. The store room must be dry.
b. Do not expose the machine to extreme cold or heat environment.
c. Place the machine on an even floor in order to avoid any distortion.
(7) Other Reminders
a.
b.
c.
d.
e.
f.
Do not alter or bypass protective interlocks.
An operation manual must remain attached to the machine at all times.
Do not alter the equipment or circuitry unless authorized to do so by the manufacturer.
Do not operate the machine with the table tops or covers removed.
Never put any part of your body near, under or into a moving machine.
Do not overload the machine by exceeding the performance limitations specified in
this manual.
2. Construction and Units
Strapping head unit
Control Panel
Reel unit
Body frame unit
-2-
3. General Safety Remarks
(1) Basic Operation
The manual and the safety remarks are to be read before use. The operator manual should
be kept with the machine at all times. Intervals for maintenance and inspections are to be
adhered to.
This machine was built with state of the art technology and rigid adherence to safety
standards.
Unless used properly, it can cause injury to operators or persons in close proximity to the
machine. In addition, improper use can cause damage to the machine or property around
the machine.
(2) Basic Safety Precautions
The user is to be instructed in all other generally applicable legal and other mandatory
regulations relevant to accident prevention and environmental protection in addition to the
operating instructions.
For safety reasons, long hair must be tied back or otherwise secured, garments must be
close fitting and no jewelry may be worn.
Use protective equipment whenever required by circumstances or by law.
Carefully observe all safety instructions and warnings attached to the machine and make
sure that they are always complete and perfectly legible.
Always make certain that persons being trained and instructed in working on or with the
machine are permanently supervised by an experienced person.
Work on the electrical system and equipment of the machine is only to be carried out by a
skilled electrician or by persons under the supervision and guidance of a skilled electrician
and in accordance with the rules and regulations of electrical engineering.
(3) Safety Instructions Governing Specific Operational Phases
Avoid any operation mode that might be unsafe.
All necessary precautions to ensure that the machine is only used being in a safe and
reliable state are to be taken. The machine is only to be operated if all protective and
safety devices, including removable safety devices, emergency shut-off equipment,
noise-protection elements and exhaust systems are in right place and fully functional.
The machine is to be checked for damage and defects at least once per work shift. Any
changes including the working behavior of the machine are to be reported to competent
-3-
persons immediately. If necessary, the machine is to be stopped and locked immediately.
In case of any malfunction the machine must be stopped and locked until the defect has
been eliminated.
Generally make sure that nobody is at risk before starting up the machine.
All personnel that will be operating this machine should be thoroughly trained in all
phases of operation and safety.
Always tighten unscrewed connections after maintenance and repair.
After completing maintenance and repair, all safety devices removed for setting up or
repairing the machine must be reinstalled and checked for functionality prior to putting the
machine back into service.
To minimize the environmental impact all consumables and replaced parts must be
disposed of safely.
Before starting the machine, check that the accessories have been stowed away safely.
Do not attempt any operation that may be a risk to the stability of the machine.
(4) Warning of Electrical Dangers
Immediately remove power to the machine in case of trouble in the electrical system.
Replace a fuse with one with the same style and ratings; pay particular attention to
matching the specified current.
Any electrical work performed on the equipment must be conducted by a skilled
electrician or under the supervision of a skilled electrician. All work must be observed
good electrical engineering practice and follow safety rules and local wiring standards.
Inspect the electrical equipment of the machine at regular intervals. Tighten any loose
connections. Check wiring for scorch marks; replace scorched wiring and determine and
correct the reason for the overheating.
When working on live equipment, ensure that a second person is available to cut power in
case of an emergency. When appropriate, secure the working area with safety tape and a
warning sign. Use insulated tools for electrical work.
Before working on high-voltage assemblies, turn off the power supply. Carefully discharge
the supply cable and short-circuit any energy-storage components such as capacitors.
If the equipment was moved, carefully refit and refasten all parts removed for transport
before reapplying power.
Before moving the machine, remember to disconnect the power cable.
-4-
(5) Grounding Instructions Shall Include the Following
This product must be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock. This product is equipped with a cord that has a
grounding wire and an appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
If repair or replacement of the cord or plug is necessary, connect the ground wire to the
ground terminal of the plug. The wire with green insulation (with or without yellow stripes)
is the grounding wire.
Check with a qualified electrician or service person if the grounding instructions are not
clear or if in doubt about the proper grounding of the machine. Do not modify the plug
provided; if it will not fit the power outlet, have the proper outlet installed by a qualified
electrician.
This product is designed for use on a nominal 120 (230) volt AC circuit and has a
grounding plug.
DANGER!
Improper installation of the grounding can result in electrocution.
4. Machine Information
(1) Areas of Application and Machine Description
This plastic strapping machine can be used for a wide range of applications where the
minimum package width is at least 80mm, and the minimum height is 20mm.
This machine is particularly suitable for heavy packaged goods as well as printed products,
boxes, etc.
Machine Description
Semi-automatic plastic strapping machine for use with polypropylene strapping.
Heavy duty construction.
Simple, safe and user-friendly operation.
Moveable, with large table area high capacity strap reel and stainless steel table.
Two locking castors, to ensure safe operation.
-5-
Environment Information
The strapping machine shall be installed in the following conditions:
z
Supply voltage: 0.9 - 1.1 nominal supply voltage
z
Source frequency: 0.99 - 1.01 nominal frequency
z
Ambient temperature: 5°C - 40°C (41℉-104℉).
z
z
Relative humidity: not exceed 50% at 40°C.
Please provide a suitable illumination around the machine for safety operation.
(2) The Safety Devices
1
2
Caution!
The heating unit operates at a very high temperature in order to melt the P.P. strapping.
To prevent burns, avoid contact with this area. (1)
To move the machine, the two lockable casters (2) must be unlocked. Relock the two
casters when the machine is in its new position.
Description of the Safety Devices
The machine is turned on when it is connected to AC power and the main power switch
(QS1), located on the front operating panel, is placed in the ON position. After
approximately 3 minutes, the heating element will reach its operating temperature and the
machine will be ready for use.
If it is necessary to make adjustments inside the machine during operation, after a strap
jam for example, the table top can be unscrewed. Observe caution as the machine is still
fully functional with the covers removed. If machine with safety switch, when table top is
opened, safety switch is activated.
-6-
(3) Electrical Specifications
System configuration：
Nominal power：
Rated current：
Rated voltage：
Rated frequency：
Type of current：
1L+N+PE (Ground)
0.5 KW
7A
220V/230V/240V
50Hz
AC - single phase
1L+N+PE (Ground)
0.5 KW
10A
110V
60Hz
AC - single phase
Minimum Requirements
The electrical supply line for the machine must have a minimum cross-section of at least
3C × 1.0mm2.
(4) Technical Data
a. TP-201 / TP-201CE
MODEL
TP-201 / TP-201CE
Sealing method
Heat
Net Weight
100kg (220 lbs)
Max. Tension
45kg (99 lbs)
Strap Width
6mm to 15.5mm (1/4" to 5/8")
Noise emission
78 dB (A)
Ambient temp
5 o C ~ 40 o C (41 o F ~ 104 o F )
b. TP-202 / TP-202CE
MODEL
TP-202 / TP-202CE
Sealing method
Heat
Net Weight
85kg (187 lbs)
Max. Tension
45kg (99 lbs)
Strap Width
6mm to 15.5mm (1/4" to 5/8")
Noise emission
78 dB (A)
Ambient temp
5 o C ~ 40 o C (41 o F ~ 104 o F )
-7-
c. TP-202L / TP-202LCE
MODEL
TP-202L / TP-202LCE
Sealing method
Heat
Net Weight
80kg (176 lbs)
Max. Tension
45kg (99 lbs)
Strap Width
6mm to 15.5mm (1/4" to 5/8")
Noise emission
78 dB (A)
Ambient temp
5 o C ~ 40 o C (41 o F ~ 104 o F )
d. TP-203 / TP-203CE
MODEL
TP-203 / TP-203CE
Sealing method
Heat
Net Weight
80kg (176 lbs)
Max. Tension
9kg ~ 30kg (19.8 lbs ~ 66.1 lbs)
Strap Width
6mm to 15.5mm (1/4" to 5/8")
Noise emission
78 dB (A)
Ambient temp
5 o C ~ 40 o C (41 o F ~ 104 o F )
e. TP-201Y / TP-201YS
MODEL
TP-201Y / TP-201YS
Sealing method
Heat
Net Weight
125kg (275 lbs)
Max. Tension
45kg (99 lbs)
Strap Width
6mm to 15.5mm (1/4" to 5/8")
Noise emission
78
Ambient temp
dB (A)
o
5 C ~ 40 o C (41 o F ~ 104 o F )
-8-
(5) How to Remove/Handle the Machine from the Pallet
Two people stand on each side of the machine and remove the machine from the pallet to
the floor.
-9-
5. Machine and Operating Element
11
(1)
Power Switch
The motor starts running when this switch is turned ON.
(2)
Feeding Length Knob
Strap is automatically fed during the time preset by the knob.
(3)
Reset Button
To pull strap back into machine and / or to cut off strap.
(4)
Strap Feed Button
To feed strap out of machine freely.
(5)
Power Plug
To be connected to a 110V or 220V/230V/240V source.
(6)
Strap Reel
Slide on strap coil here. (If strap core is 280mm, you can
take off the center drum to have core size 200mm.)
(7)
Brake
Stops the over-rotation of the Strap reel.
(8)
Strap Guide for Brake
The strap is threaded through this guide.
(9)
Strap Bypass Guide
The strap is passed through this guide.
(10) Strap Insertion Inlet
This is the strap inlet at which the leading strap end is
detected.
(11) Tension control
Turn clockwise to increase tension and counter clockwise to
decrease tension
-10-
6. Operating the Machine
(1) Operation Space
Keep the area (A) and (B) free for the operator.
The area (A) is necessary for operation strapping machine or changing the strap coil
(TP-202).
For TP-201/TP-203, the area (B) is necessary for changing the strap coil.
B
B
A
A
TP-202
TP-201 / TP-203
(2) How to Load and Thread P.P. Strap
a.
b.
c.
d.
e.
f.
g.
h.
Turn reel nut handle (A) left and remove it.
Remove the outer flange (B) and install the strap reel.
Make sure that the direction of rotation is counterclockwise (E) when unrolling.
Put the outer flange back on and tighten reel nut handle (A) to the right.
Remove all adhesive strips or other adhesive material.
Unroll about 1.5 m of strap and make sure that it is not twisted.
Thread the strap over (C) to roller (D) in direction of the arrow.
Turn left button (strap feed) to the left until obtaining the length you need.
D
C
E
A
B
-11-
(3) How to Operate
a. Turn the power switch ON. The heating element reaches the working temperature at
approximately 3 minute.
b. Place a package on the table top (The package must cover the Slide Table).
c. Properly adjust the strap tension according to various package.
d. Place the strap around the package to be strapped and insert the strap into the strapping
head until it stops.
e. The strapping and welding sequence should complete.
f. At end of strapping sequence the strap end is fed automatically, and Feeding Length
Knob is to adjust the strap length.
7. Adjustments
(1) Strap Width
Adjustment for strap in different width can be done with only one Philips recess
screw driver and a hex spanner. The adjustment must be made in two places, A (Strap
Outlet), B (Strap Inlet) as shown below.
For A, the width of band guide should be at 12.5mm to 13.0mm when using 9mm and
12mm strap and the width of band guide should be at 15.5mm to 16mm when using 15mm
strap.
For B, The width of band guide should be wider by 0.5mm to 1.0mm than the actual
strap width.
Fig. B
Fig. A
Strap Inlet
The adjustment is made with the
guide located on the top of the
table. Make both adjustments
by loosening two screws and
applying the strap which is to be
used.
Strap Outlet
-12-
(2) Inside Tension Adjustment (For TP-201Y)
Tensioning strength should be adjusted properly by observing the tension of the strap
applied around the package.
The adjustment is made by tensioning adjustment nut A. Tensioning adjustment nut A is
turned clockwise to increase the strength and counterclockwise to decrease strength.
After adjustment, nut A should be fixed by a set screw.
(3) Outside Tension Adjustment (For TP-201/TP-202/TP-203/TP-202L)
The adjustment is made by tensioning adjustment nut A which is located at the back of the
machine.
Tensioning adjustment nut A is turned clockwise to increase the strength and
counterclockwise to decrease strength.
-13-
(4) Heater temperature
Set the knob to position 3 or 4. Adjust the heater temperature by selecting a position
between l and 6. Choose the suitable temperature, bearing in mind the environmental
conditions of the machine. If the heater temperature is too high or too low, a proper seal
will not be obtained.
Gradually increase or reduce the position until obtaining an optimum seal.
8. Maintenance & Lubrication
Warning:
Before any maintenance or repairs on the machine, set the Power Switch to
"O" (OFF). Wait about 5 minutes for cooling down the heater to avoid burns
with this area.
(1) Cleaning and Lubrication
The high reliability and long service life of the strapping machine will depend on regular
cleaning and maintenance.
ATTENTION!
All the important strap transport components, such as the tension rollers and the
strap guides, must be kept free from oil and grease. (lubricant)
The lubricant has to be non-resinous.
The lubricant is SAE 30
-14-
(2) Maintenance
Only use original spare parts supplied by manufacturer.
Daily:
Use air gun to clean the circled positions (nearby the cutters, strap guide daily
Remove plastic residue in the machine.
Air
Air
Weekly:
Lubricate front bar, press bar and rear bar weekly.
Please refer to the above mesh areas for instruction.
Before lubricating, be sure to clean the parts first to avoid mixing oil and debris which
might have a bad effect on machine’s function.
Monthly :( or 3,000 strapping cycles)
Clean both sides of heater plate and polish with fine sandpaper if necessary
ATTENTION: Make sure the welding plate is cool first!!
Check cam rollers of seal head for easy movement. Slide table back to home position
automatically by the spring tension.
Be sure to clean any debris in the tension roller
6 Months:（or 18,000 strapping cycles）
Check heater plate, replace and readjust it if necessary.
Check strap cutter in seal head, replace it if necessary.
Check that connector at wiring loom to printed circuit board is firmly fixed.
Make machine ready for operation. Strap one bundle manually several times, paying
attention to mal-functions, repeat procedure.
-15-
1 year :( or 36,000 strapping)
Replace deflection roller if it shows visible changes.
In case of loud noise at bearings: locate them, replace the bearings.
Get machine ready for operation again, strap one bundle manually several times, paying
attention to malfunctions.
9. Troubleshooting Guide
(1) Strap Jams in the Groove
Step1. Turn the power switch off and pull out the strap strongly in tensioning direction.
-16-
Step2. In case this remedy does not work due to strap jam, follow the instructions listed
below.
a. Loosen M5 Set screw (Part No. 5)
b. Remove Pin (Part No. 6) then lift Holder (Part No. 7) and repeat step 1. If this is
not successful, continue
c. Remove Strap Inlet Guides (Page 12 (B))
d. Remove M6 Hexagon Bolts (Part No. 3)
e. Remove Holder Arm (Part No. 4) from Holder (Part No. 7)
f. Lift out Holder (Part No. 7) and eliminate jam.
g. Reassemble from (f.) back to (a.)
-17-
(2) The Strap Does Not Feed Past the Infeed Guide
This failure is caused if the front bar is in the raised position (previous cycle has not been
completed). Turn the Power switch "off ", then "on" again.
If this does not eliminate the failure, adjust the lever for LS1 to allow LS1 to be activated
and de-activated correctly.
*More troubleshooting guide is on request.
-18-
10. Wiring Diagram
-19-
PART ҈
CONTENTS
1. Spare Parts List …………………………………1
REF.
PART NO.
NO.
1
TA-900
TA-901
TA-901S
DESCRIPTION
Q'TY
TA-903
T5-1-10110
TA-003
KYA050530
KYA0505101
KYA050515
ER12
TA-008-2
HBS0620
HBS0645H
BR6003ZZ
TA-012A
TA-012B
HSS0608G
TA-014
TA-015A
TA-015B
TA-016
TA-017-2
TA-018
Strapping Head Unit (For TP-202)
Strapping Head Unit (For TP-201)
Strapping Head Unit (Stainless Steel
Model)(For TP-201CES)
Strapping Head Unit (For TP-201Y)
Strapping Head Unit (Stainless Steel
Model)(For TP-201YS)
Strapping Head Unit (For TP-203)
Main Body Block
Cam Shaft
Key, 5×5×30
Key, 5×5×101
Key, 5×5×15
Snap Ring, E-12
Bearing Support (L)
HBS, M6×20
HBS, M6×45 (H)
Bearing, 6003ZZ
Grip Cam
Grip Cam
HSS, M6×8 (G)
Separator Cam
Rear Bar Cam
Heater Cam
Sprocket
Bearing Support (R)
Pulley
1
1
1
1
1
2
3
1
6
1
4
1
1
13
1
1
1
1
1
1
20
TA-020
Pulley
1
22
23
24
25
TA-022
TF-002
TA-024
TA-025
Chain
Micro Switch Bracket
Back Cam
Collar
1
1
1
1
27
28
TA-027
TA-028
Sprocket
Housing
1
1
TA-902
TA-902S
2
3
4
5
6
7
8
9
10
11
12A
12B
13
14
15A
15B
16
17
18
-2-
1
1
1
1
1
REMARKS
REF.
NO.
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PART NO.
DESCRIPTION
Q'TY
TA-029
TA-030
PMS0408
TA-032
TA-033
TA-034
TA-035
KYA050520
TA-037
HBS0616
TF-009
TA-040
PMS0420
TA-042
HBS0820
TF-022
KYA050525
Pin
Holder
PMS, M4×8
Spring
Stop Arm
Clutch Arm
Shaft
Key, 5×5×20
Clutch Support
HBS, M6×16
Switch Trigger
Guide
PMS, M4×20
Gear Box
HBS, M8×20
Washer
Key, 5×5×25
1
1
6
1
1
1
1
1
1
14
1
1
1
1
4
1
2
58
59
60
61
62
63
TA-058
SW06
TA-060
SP0414
TF-028
HBS0510
Pull Shaft
SW, M6
Solenoid Shaft
Spring Pin, 4×14
Fan
HBS, M5×10
1
19
1
1
1
4
67
TA-067
Bar Guide Lid
1
69
TA-069
TA-069S
SP0318
TA-071
TA-072
TA-073
TA-074
TA-074S
Press Bar
Press Bar (Stainless Steel Model)
Spring Pin, 3×18
Return Spring
Spring Hook
Spring Hook
Rear Bar
Rear Bar (Stainless Steel Model)
1
1
3
3
1
3
1
1
70
71
72
73
74
-3-
REMARKS
REF.
NO.
75
76
77
78
79
80
81
82
84
85
86
87
88
89
90
91
92
94
95
96
99
PART NO.
DESCRIPTION
Q'TY
TA-075
BR635ZZ
SP0514
TA-078
TA-079
TA-079S
TA-080
TA-080S
HBS0505.2
HBS0505.2S
SP0314
Plunger
Bearing, 635ZZ
Spring Pin, 5×14
Spring
Front Bar
Front Bar (Stainless Steel Model)
Slide
Slide (Stainless Steel Model)
HBS, M5×5.2
HBS, M5×5.2 (Stainless Steel Model)
Spring Pin, 3×14
3
4
3
3
1
1
1
1
1
1
1
PMS0315
HN08
TA-086
TA-087
TA-088
TA-089
TA-090
SP0620
HBS0525
TA-094
TA-095
TA-095S
HBS0512
HBS0512S
PMS, M3×15
HN, M8
Seal
Switch Lever
Seal (Small)
Spring Hook
Arm
Spring Pin, 6×20
HBS, M5×25
Shaft
Guide (L)
Guide (L)(Stainless Steel Model)
HBS, M5×12
HBS, M5×12 (Stainless Steel Model)
6
2
1
1
1
1
1
1
1
1
1
1
4
4
TF-001
TF-001-1D
TF-001-1B
TF-001-2
TF-001-B
Motor (For 110V/60HZ)
Motor (For 220V/50HZ)
Motor (For 220V/60HZ)
Motor (For 240V/50HZ)
Motor (For 100V, 50/60HZ)
1
1
1
1
1
-4-
REMARKS
REF.
NO.
114
115
116
117
118
PART NO.
DESCRIPTION
Q'TY
TA-114
TA-003A
TA-035A
TA-058A
TA-080A
TA-080AS
TA-083A
TA-083AS
TF-002A
TF-003A
TF-003A-1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
122
123
124
T5-1-13000
T5-1-14000
T5-1-15000
Spring
Cam Ass'y
Stop Arm Ass'y
Pull Shaft Ass'y
Slide Ass'y
Slide Ass'y (Stainless Steel Model)
Separator Ass'y
Separator Ass'y (Stainless Steel Model)
Micro Switch Bracket Ass'y
D.C.Solenoid Ass'y (For 110V)
D.C.Solenoid Ass'y
(For 220V/230V/240V)
Rear Bar Ass'y
Press Bar Ass'y
Front Bar Ass'y
226
227
228
229
TA-226
TA-226S
TB-114
TA-228
TA-229
Guide (R)
Guide (R)(Stainless Steel Model)
Return Spring
Belt
Collar
1
1
1
1
2
236
TA-236
Rubber Buffer
1
238
239
240
241
ER03
TA-239
HBS0516
TA-241
Snap Ring, E-3
Cutter Holder
HBS, M5×16
Spacer
1
1
4
3
244
245
246
247
248
249
HSS0506G
HSS0606G
PW06C
HN06
HN04
SW04
HSS, M5×6 (G)
HSS, M6×6 (G)
PW, M6 (C)
HN, M6
HN, M4
SW, M4
2
2
16
6
1
4
119
120
121
-5-
REMARKS
REF.
NO.
250
251
252
253
254
255
256
258
PART NO.
SW05
PW05
HBS0525H
HN05
SW08
HN03
PW06A
TF-044
TF-045
TF-046
TF-047
259
260
261
262
263
264
265
TF-006
LA-50082
LA-50080
SW03
LA-50084
TF-071
PW08C
DESCRIPTION
SW, M5
PW, M5
HBS, M5×25 (H)
HN, M5
SW, M8
HN, M3
PW, M6 (A)
Start Capacitor (220V/50HZ)
Start Capacitor (220V/60HZ,
240V/50HZ)
Start Capacitor (110V/60HZ)
Start Capacitor (100V/50HZ,
100V/60HZ)
Micro Switch (LS-1, LS-3)
Label (LS-3)
Label (LS-1)
SW, M3
Label (SOL-2)
Varistor
PW, M8 (C)
-6-
Q'TY
5
2
1
2
5
3
2
1
1
1
1
2
1
1
8
1
1
4
REMARKS
REF.
NO.
101
102
103
104
105
106
107
PART NO.
DESCRIPTION
Q'TY
PW04
TB-102
TB-103
HN08
ER06
HBS0440H
TB-107
PW, M4
Heater Arm
Pin
HN, M8
Snap Ring, E-6
HBS, M4×40 (H)
Side Plate
2
1
1
1
1
2
1
113
114
115
117
118
TB-113
TB-114
TB-115
TB-117
TB-118
TB-118A
1
1
1
4
1
1
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
SR15
KYA050515
HSS0506G
TB-122
TB-123
TB-124
HSS0606G
HSS0508G
TB-127
TB-128
TB-129
TB-130
HB06100
HN06
TB-133
TB-134
TB-135
HBS0616
TB-137
KYA050520
TB-139
RR22
Heater Ass'y
Return Spring
Spring
Roller
Shaft (For Inside Tension Adjustment)
Shaft (For Outside Tension
Adjustment)
Stop Ring, S-15
Key, 5×5×15
HSS, M5×6 (G)
Shaft
Holder
Pin
HSS, M6×6 (G)
HSS, M5×8 (G)
Gear
Collar
Feed Gear
Spring
HB, M6×100
HN, M6
Nut
Gear
Holder Arm
HBS, M6×16
Shaft
Key, 5×5×20
Pulley
Snap Ring, H-22
-8-
10
9
2
1
1
1
1
3
3
7
1
1
1
12
1
1
1
4
1
2
1
1
REMARKS
REF.
NO.
141
142
143
144
145
146
147
148
149
150
151
152
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
173
174
175
175A
176
PART NO.
DESCRIPTION
Q'TY
TB-141
BR608ZZ
TB-143
TB-144
ER07
TB-146
RR32
TB-148
TB-123B
TB-210A
PMS0315
TB-152
TB-154
TB-155
BR6002ZZ
TB-157
TB-158
HBS0620
TB-160
TB-158A
TB-162
KYA050538
TB-164
TB-165
SP0520
BR635ZZ
TB-168
SW04
TB-170
TB-160B
Pulley
Bearing, 608ZZ
Round Belt
Shaft
Snap Ring, E-7
Arm
Snap Ring, H-32
Bracket
Roller Holder Ass'y
Roller Bracket Ass'y
PMS, M3×15
Shaft
Spring
Nut
Bearing, 6002ZZ
V-Belt
Bracket
HBS, M6×20
Bracket
Bracket Ass'y
Shaft
Key, 5×5×38
Shaft
Feed Arm
Spring Pin, 5×20
Bearing, 635ZZ
Arm Pin
SW, M4
Pulley
Bracket Ass'y
2
1
1
1
1
1
2
1
1
1
2
1
1
1
12
1
1
6
1
1
1
1
1
1
1
3
1
6
1
1
TB-173
TB-165A
TB-175
TB-175A
TB-176
TJ-025
V-Belt
Feed Arm Ass'y
Plate
Plate
Friction Disc
Friction Disc (Only TP-203)
1
1
1
1
2
2
-9-
REMARKS
REF.
NO.
177
178
179
180
181
TB-177
TB-170A
TB-177A
PW06A
SP0414
Pull Shaft
Pulley Ass'y
Pull Shaft Ass'y
PW, M6 (A)
Spring Pin, 4×14
1
1
1
19
1
183
184
185
186
187
189
TB-183
TB-184
HBS0510
TB-186
TB-187
TB-189
Spring
Stop Bracket
HBS, M5×10
Spring
Spring
Retainer
1
1
6
1
1
1
192
193
195
196
197
199
200
201
203
TB-192
TB-193
TB-195
PMS0410
TB-197
TB-199
SR10
TB-201
TB-203
TB-203L
FMS0408
TB-205
TB-206
TB-207
TB-208
TB-209
TB-210
RR19
HBS0525H
TB-215
HB0680
PMS0412
HN05
Roller
Cover
Outlet Cover
PMS, M4×10
Guide Front
Pin
Stop Ring, S-10
Outlet Guide
Guide
Guide (Longer)(Option)
FMS, M4×8
Guide
Cover
Cover-Side
Front Plate
Band Plate
Pulley
Snap Ring, H-19
HBS, M5×25 (H)
Collar
HB, M6×80
PMS, M4×12
HN, M5
1
1
1
7
1
1
2
1
1
1
10
1
1
2
1
1
1
1
1
1
1
3
3
204
205
206
207
208
209
210
212
213
215
216
220
221
PART NO.
DESCRIPTION
-10-
Q'TY
REMARKS
REF.
NO.
223
224
225
TB-223
TB-224
TB-225
Washer
Spring Retainer
Bushing
2
2
1
231
232
234
TB-231
TB-232
HBS0665H
Pin
Bracket
HBS, M6×65 (H)
1
1
1
246
247
248
249
250
251
SR40
HBS0506
TB-248
BR6005ZZ
TB-250
TB-251
TJ-251
HBS0512
TB-255
TB-256
TB-257
TB-258
T7-3-40480
TB-262
HBS0516
HSS0606G
SW08
HN04
PW04
SW05
SW06
PW05
SW03
TF-007
LA-50081
LA-50083
TF-071
Stop Ring, S-40
HBS, M5×6
Spring Retainer
Bearing, 6005ZZ
Tube A
Tube B
Tube B (Only TP-203)
HBS, M5×12
Fix Arm (Only TP-201)
Corrector
Fix Arm (For TP-202/TP-202L)
Bolt (For TP-202/TP-202L)
Spring (Only TP-201Y)
Tube
HBS, M5×16
HSS, M6×6 (G)
SW, M8
HN, M4
PW, M4
SW, M5
SW, M6
PW, M5
SW, M3
Micro Switch (LS-2)
Label (LS-2)
Label (SOL-1)
Varistor
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
7
3
6
15
1
2
1
1
1
1
254
255
256
257
258
260
262
263
264
265
266
267
268
269
270
271
272
273
274
275
PART NO.
DESCRIPTION
-11-
Q'TY
REMARKS
REF.
PART NO.
NO.
276 FLG06
277 TF-003A
TF-003A-1
278
279
280
281
282
283
TB-263
FMS0406
TA-060
TA-086
ER12
TB-264
TJ-252
DESCRIPTION
Q'TY
FLG, M6
D.C. Solenoid Ass'y (For 110V)
D.C. Solenoid Ass'y
(For 220V/230V/240V)
Tube
FMS, M4×6
Solenoid Shaft
Seal
Snap Ring, E-12
Tension Adjusting Ass'y
Tension Adjusting Ass'y (Only TP-203)
6
1
1
-12-
1
2
1
1
1
1
1
REMARKS
REF.
NO.
1
2
3
4
5
PART NO.
DESCRIPTION
Q'TY
TE-001
TC-014
TE-003
TC-015
TB-255-1
Inner Flange
Outer Flange
Shaft
Protector
Rubber
1
1
1
1
1
7
8
TC-016
TC-004
Reel Nut Handle
Package Guide
1
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
TE-010
TE-011
TE-012
TE-013
TE-013S
TE-014
TC-002
TC-008
TE-017
TE-018
TC-020
TC-021
TE-021
TE-022
TE-023
TE-024
TE-025
ER04
TE-027
TE-028
TE-029
TE-030
TC-049
TC-048
Grommet
Caster (Free)
Caster (Brake)
Lock Pin
Lock Pin (Stainless Steel Model)
Brake Holder (R)
Bracket
Grommet
Bushing (L)
Bushing (R)
Pin
Split Pin
Brake Set
Pin
Rubber Stop
Brake Holder (L)
Spring
Snap Ring, E-4
Roller Holder
Roller
Pin
Band Guide Bracket
Roller
Shaft
2
2
2
4
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
38
40
TMS0508
TE-033
TMS, M5×8 (Only CE)
Right Side Plate (Only CE)
6
1
-14-
REMARKS
REF.
PART NO.
NO.
41 TE-041
TE-041S
TK-033
TK-033S
DESCRIPTION
Q'TY
1
1
1
1
47
48
49
TE-042
TE-043
TE-043S
TE-044
TE-044S
TE-045
TE-045S
TC-043
TC-043S
TE-001A
TE-021A
TE-030A
Body Frame
Body Frame (Stainless Steel Model)
Body Frame (Only CE)
Body Frame (Stainless Steel Model)
(Only CE)
Magnet Catch
Side Door (L)
Side Door (L)(Stainless Steel Model)
Side Door (R)
Side Door (R)(Stainless Steel Model)
Support
Support (Stainless Steel Model)
Top Plate
Top Plate (Stainless Steel Model)
Reel Unit
Brake Arm Ass'y
Band Guide Bracket Ass'y
51
HB0612
HB, M6×12
20
53
TMS0305
TMS, M3×5
8
55
56
57
58
59
60
61
HBS0620
HB0620
SW06
SR10
PW06C
PW06A
PW06B
HBS, M6×20
HB, M6×20
SW, M6
Stop Ring, S-10
PW, M6 (C)
PW, M6 (A)
PW, M6 (B)
7
2
27
3
30
2
2
63
64
WN06
HN06
WN, M6
HN, M6
2
11
67
68
69
70
TMS0612
TC-068
NTE06
TC-070
TMS, M6×12
Collar
NTE, M6
Shaft
1
1
2
2
42
43
44
45
46
-15-
4
1
1
1
1
1
1
1
1
1
1
1
REMARKS
REF.
PART NO.
NO.
71 FMS0612
DESCRIPTION
Q'TY
FMS, M6×12
1
73
T5-2-10170
Hinge
1
75
76
77
78
TC-075
TC-076
ER19
TB-205
Center Drum 280mm
Washer
Snap Ring, E-19
Guide
1
1
1
1
84
85
86
87
HBS0612
TMS0408
SW04
HN04
HBS, M6×12
TMS, M4×8
SW, M4
HN, M4
2
2
2
2
89
90
91
PW05
SW05
HN05
PW, M5
SW, M5
HN, M5
4
4
4
94
95
96
HB0610
PMS0408
LA-31010
HB, M6×10
PMS, M4×8
Label
1
2
1
-16-
REMARKS
REF.
NO.
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
PART NO.
DESCRIPTION
Q'TY
TC-001
TC-002
TC-003
TC-004
TC-005
TC-006
TC-007
TC-008
TC-009
BR6003ZZ
TC-011
TC-013
TC-014
TC-015
TC-016
Protection Cover
Bracket
Reel Shaft
Package Guide
Lid
Caster (Free)
Caster (Brake)
Grommet
Brake Shaft
Bearing, 6003ZZ
Washer
Inner Flange
Outer Flange
Protector
Reel Nut Handle
1
1
1
1
5
2
2
1
1
2
1
1
1
1
1
18
19
20
21
22
24
25
30
31
32
33
TC-018
TC-019
TC-020
TC-021
TC-022
TC-024
TC-025
T7-5-10160
TC-031
T5-3-11000
TC-047A
Brake Lining
Roller
Pin
Split Pin
Roller Holder
Brake Adjuster
Spring
Adjustment Leg (Option)
Fix Plate (Option)
Reel Control Group
Roller Bracket Ass'y
1
1
1
1
1
1
1
4
4
1
1
38
39
41
TMS0508
SW16
TC-041
TK-031
TC-042
TC-043
TC-044
TMS, M5×8
SW, M16
Body Frame
Body Frame (Only CE)
Support
Top Plate
Reel Support
6
4
1
1
1
1
1
42
43
44
-18-
REMARKS
REF.
NO.
45
46
47
48
49
50
51
52
53
54
55
56
PART NO.
DESCRIPTION
Q'TY
TC-045-1
TC-046-1
TC-047
TC-048
TC-049
TC-050
HB0612
PW06C
FMS0512
HBS0620
SW05
PW06A
Fixing Brake Lining Bracket
Arm
Roller Bracket
Shaft
Roller
Lining Holder
HB, M6×12
PW, M6 (C)
FMS, M5×12
HBS, M6×20
SW, M5
PW, M6 (A)(Option)
1
1
1
1
1
1
4
14
2
7
2
8
61
62
63
64
65
66
67
68
69
70
71
PW05
SW06
SW06
SW08
HBS0616
HBS0616
WN06
HN06
HBS0816
HB0816
SR20
SR10
TMS0612
TC-068
NTE06
TC-070
FMS0612
PW, M5
SW, M6
SW, M6 (Option)
SW, M8
HBS, M6×16
HBS, M6×16 (Option)
WN, M6
HN, M6
HBS, M8×16
HB, M8×16
Stop Ring, S-20
Stop Ring, S-10
TMS, M6×12
Collar
NTE, M6
Shaft
FMS, M6×12
2
10
18
4
2
10
2
9
4
1
2
2
1
1
2
2
1
73
74
75
76
77
78
T5-2-10170
PW06B
TC-075
TC-100
TC-110
TB-205
Hinge
PW, M6 (B)
Center Drum 280mm
Adjustment Leg Ass'y (Brake)(Option)
Adjustment Leg Ass'y (Free)(Option)
Guide
1
2
1
2
2
1
57
58
59
60
-19-
REMARKS
REF.
NO.
79
80
81
82
83
84
85
91
92
93
94
95
96
97
PART NO.
TC-076
ER19
HBS0525H
HN05
PMS0416
PW04
TMS0408
SR15
TC-092
LA-50094
HN05
HB0610
TC-094
LA-31010
DESCRIPTION
Washer
Snap Ring, E-19
HBS, M5×25 (H)
HN, M5
PMS, M4×16
PW, M4
TMS, M4×8
Stop Ring, S-15
Holder
Label (Option)
HN, M5
HB, M6×10
Spacer
Label
-20-
Q'TY
1
1
1
4
4
4
2
1
1
4
2
1
1
1
REMARKS
REF.
NO.
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
PART NO.
DESCRIPTION
Q'TY
TD-001
TC-002
TD-003
TC-004
TC-005
TC-006
TC-007
TC-008
TC-009
BR6003ZZ
TC-011
TC-013
TC-014
TC-015
TD-016
Protection Cover
Bracket
Reel Shaft
Package Guide
Lid
Caster (Free)
Caster (Brake)
Grommet
Brake Shaft
Bearing, 6003ZZ
Washer
Inner Flange
Outer Flange
Protector
Reel Nut Handle (LH)
1
1
1
1
5
2
2
1
1
2
1
1
1
1
1
18
19
20
21
22
24
25
TD-018
TC-019
TC-020
TC-021
TC-022
TD-024
TC-025
Brake Lining
Roller
Pin
Split Pin
Roller Holder
Spring Hook
Spring
1
2
1
1
1
1
1
38
39
41
TMS0508
SW16
TD-041
TK-041
TC-042
TC-043
TD-044
TC-045-1
TD-046-1
TD-047
TD-048
TD-044A
TMS, M5×x8
SW, M16
Body Frame
Body Frame (Only CE)
Support
Top Plate
Reel Support
Fixing Brake Lining Bracket
Arm
Roller Bracket
Shaft
Reel Support Ass'y
6
4
1
1
1
1
1
1
1
1
1
1
42
43
44
45
46
47
48
49
-22-
REMARKS
REF.
NO.
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
PART NO.
DESCRIPTION
Q'TY
TC-050
HB0612
HB0610
FMS0512
HBS0620
SW05
PW06C
PW05
SW06
TD-047A
PW06B
WN06
HN06
HBS0616
HB0816
SR20
SR10
TMS0612
TC-068
NTE06
TC-070
FMS0612
PW06A
T5-2-10170
Lining Holder
HB, M6×12
HB, M6×10
FMS, M5×12
HBS, M6×20
SW, M5
PW, M6 (C)
PW, M5
SW, M6
Roller Bracket Ass'y
PW, M6 (B)
WN, M6
HN, M6
HBS, M6×16
HB, M8×16
Stop Ring, S-20
Stop Ring, S-10
TMS, M6×12
Collar
NTE, M6
Shaft
FMS, M6×12
PW, M6 (A)
Hinge
1
2
2
2
7
2
14
2
14
1
2
2
9
5
1
2
3
1
1
2
2
1
2
1
75
76
77
78
TC-075
TC-076
ER19
TB-205
Center Drum 280mm
Washer
Snap Ring, E-19
Guide
1
1
1
1
81
82
83
84
HBS0525H
HN05
PMS0416
PW04
HBS, M5×25 (H)
HN, M5
PMS, M4×16
PW, M4
1
4
4
6
-23-
REMARKS
REF.
PART NO.
NO.
91 SR15
92 TMS0408
94
95
96
97
98
HN05
HB0610
TC-094
LA-30200
LA-30210
DESCRIPTION
Q'TY
Stop Ring, S-15
TMS, M4×8
1
2
HN, M5
HB, M6×10
Spacer
Label
Label
2
1
1
1
1
-24-
REMARKS
REF.
NO.
1
2
3
4
7
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PART NO.
DESCRIPTION
Q'TY
TE-001
TC-014
TE-003
TC-015
TC-016
TC-004
TE-010
TC-006
TC-007
TE-013
TE-014
TC-002
TC-008
TE-017
TE-018
TC-020
TC-021
TJ-021
TE-022
TE-023
TE-024
TE-025
ER04
TE-027
TE-028
TE-029
TE-030
TC-049
TC-048
Inner Flange
Outer Flange
Shaft
Protector
Reel Nut Handle
Package Guide
Grommet
Caster (Free)
Caster (Brake)
Lock Pin
Brake Holder (R)
Bracket
Grommet
Bushing (L)
Bushing (R)
Pin
Split Pin
Brake Set
Pin
Rubber Stop
Brake Holder (L)
Spring
Snap Ring, E-4
Roller Holder
Roller
Pin
Band Guide Bracket
Roller
Shaft
1
1
1
1
1
1
2
2
2
4
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
38
39
TMS0508
SW16
TMS, M5×8 (Only CE)
SW, M16
6
4
41
TJ-001
TJ-010
TE-042
TJ-043
Body Frame
Body Frame (Only CE)
Magnet Catch
Side Door (L)
1
1
4
1
42
43
-26-
REMARKS
REF.
NO.
44
46
47
48
49
TJ-044
TJ-002
TE-001A
TE-030A
TJ-021A
Side Door (R)
Top Plate
Reel Unit
Band Guide Bracket Ass'y
Brake Arm Ass'y
1
1
1
1
1
51
53
54
55
56
57
58
59
60
63
64
HBS0612
TMS0305
PW06A
HBS0620
HB0612
SW06
SR10
PW06C
PW06B
WN06
HN06
HBS, M6×12
TMS, M3×5
PW, M6 (A)
HBS, M6×20
HB, M6×12
SW, M6
Stop Ring, S-10
PW, M6 (C)
PW, M6 (B)
WN, M6
HN, M6
2
8
2
7
4
9
4
14
2
2
9
71
72
74
75
TJ-023
TJ-024
TJ-092
TC-075
Bracket of Smoke-Exhaus Pipe
Smoke-Exhaus Pipe
Reel Assist Bracket
Center Drum 280mm
1
1
1
1
77
78
79
TC-076
ER19
TB-205
Washer
Snap Ring, E-19
Guide
1
1
1
81
83
84
85
SW04
PW05
SW05
HN05
SW, M4
PW, M5
SW, M5
HN, M5
4
2
2
2
87
88
89
90
91
PW04
HN04
PMS0408
TMS0408
LA-31010
PW, M4
HN, M4
PMS, M4×8
TMS, M4×8
Label
2
2
4
2
1
PART NO.
DESCRIPTION
-27-
Q'TY
REMARKS
REF.
PART NO.
NO.
1
TL-001
TL-001S
2
TL-002
TL-002S
3
TD-003
TD-003S
4
TL-004
TL-004S
5
TL-005
TL-005S
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
TL-007
TL-007S
TC-006
TC-006S
TC-007
TC-007S
TC-019
TL-011
TL-011S
TL-012
TL-012S
TC-013
TC-014
TL-015
TL-015S
TD-016
TL-017
TL-017S
ER07S
T6-5-11120
T6-5-11121
T6-5-11130
T6-5-11131
TL-021
TL-021S
DESCRIPTION
Q'TY
Body Frame
Body Frame (Stainless Steel Model)
Table (L)
Table (L)(Stainless Steel Model)
Reel Shaft
Reel Shaft (Stainless Steel Model)
Table (R)
Table (R)(Stainless Steel Model)
Top Plate
Top Plate (Stainless Steel Model)
1
1
1
1
1
1
1
1
1
1
Front Plate
Front Plate (Stainless Steel Model)
Caster (Free)
Caster (Free)(Stainless Steel Model)
Caster (Brake)
Caster (Brake)(Stainless Steel Model)
Roller
Table Support
Table Support (Stainless Steel Model)
Reel Support
Reel Support (Stainless Steel Model)
Inner Flange
Outer Flange
Guide
Guide (Stainless Steel Model)
Reel Nut Handle (LH)
Back Door
Back Door (Stainless Steel Model)
Snap Ring, E-7 (SUS)
Table Roller
Table Roller (Plastic)
Table Roller Shaft
Table Roller Shaft (Stainless Steel
Model)
Brake Arm
Brake Arm (Stainless Steel Model)
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
16
8
8
8
8
-29-
1
1
REMARKS
REF.
PART NO.
NO.
22 TE-027
TE-027S
23 TL-023
24 TL-024
25 HN08
HN08S
27 FMS0410
FMS0410S
DESCRIPTION
Roller Holder
Roller Holder (Stainless Steel Model)
Stopper
Bolt
HN, M8
HN, M8 (Stainless Steel Model)
FMS, M4×10
FMS, M4×10 (Stainless Steel Model)
1
1
1
1
2
2
4
4
1
1
1
1
1
4
4
2
1
2
2
2
2
2
2
1
1
30
31
32
33
TL-030
TD-047A
TL-007A
T6-4-30000
T6-4-30000S
34
SW16
SW16S
Brake lining
Roller Bracket Ass'y
Front Plate Ass'y
Reel Control Group
Reel Control Group (Stainless Steel
Model)
SW, M16
SW, M16 (Stainless Steel Model)
41
42
43
TL-041
TL-042
TD-047
TD-047S
TD-048
TD-048S
T6-2-11140
T6-2-11150
TL-047
TL-047S
Door Lock
Bracket
Roller Bracket
Roller Bracket (Stainless Steel Model)
Shaft
Shaft (Stainless Steel Model)
RH Strap Guide Flap Pin (Rear)
RH Strap Guide Flap Spring
Flap
Flap (Stainless Steel Model)
44
45
46
47
Q'TY
-30-
REMARKS
REF.
PART NO.
NO.
52 SR10
SR10S
53 HBS0816
HBS0816S
54 SW08
SW08S
55 TMS0612
TMS0612S
56 HB0610
HB0610S
57 SW06
SW06S
65
66
67
68
69
70
71
72
73
TE-028
TE-029
TE-029S
ER04
ER04S
LA-30200
LA-30210
TL-070
TL-070S
HB0616
HB0616S
SW06
SW06S
PW06C
PW06CS
DESCRIPTION
Q'TY
Stop Ring, S-10
Stop Ring, S-10 (Stainless Steel Model)
HBS, M8×16
HBS, M8×16 (Stainless Steel Model)
SW, M8
SW, M8 (Stainless Steel Model)
TMS, M6×12
TMS, M6×12 (Stainless Steel Model)
HB, M6×10
HB, M6×10 (Stainless Steel Model)
SW, M6
SW, M6 (Stainless Steel Model)
5
5
4
4
5
5
8
8
4
4
6
6
Roller
Pin
Pin (Stainless Steel Model)
Snap Ring, E-4
Snap Ring, E-4 (Stainless Steel Model)
Label
Label
Supporting Leg
Supporting Leg (Stainless Steel Model)
HB, M6×16
HB, M6×16 (Stainless Steel Model)
SW, M6
SW, M6 (Stainless Steel Model)
PW, M6 (C)
PW, M6 (C)(Stainless Steel Model)
1
1
1
2
2
1
1
4
4
16
16
16
16
16
16
-31-
REMARKS
REF.
PART NO.
NO.
5
TF-005
DESCRIPTION
Q'TY
Safety Switch Plate (Option)
1
Terminal Bracket
Cover (Only CE)
1
1
TF-018
TF-019
TF-020
TF-021
TF-021-1
22 T7-5-10210
23A TF-023A
TF-023A-1
Safety Limit Switch (For CE)(Option)
Adiabatic Plate
Fan Cover
Fan (For 110V)
Fan (For 220V/230V/240V)
Switch Actuator (Option)
Heater Transformer Ass'y (For 110V)
Heater Transformer Ass'y
(For 220V/230V/240V)
1
1
1
1
1
1
1
1
24
25
TF-024
TF-025
Transformer Cover
Knob
1
1
27
28
TF-027
TG-024
TG-025
TG-026
TG-027
TE-099
TF-029
TF-031
LA-40002
Selector Switch
Wire (For TP-201)(Option)
Wire (For TP-203)(Option)
Wire (For TP-201Y)(Option)
Wire (For Top Plate)(Option)
Safety Limit Switch Ass'y (Option)
Cover (Only TP-203)
Switch Cover (Option)
Label
1
1
1
1
1
1
1
1
1
15
16
TF-015
TF-016
18
19
20
21
29
30
31
32
-33-
REMARKS
REF.
NO.
41
42
43
TJ-022
T5-4-10310
TK-035
Fan Support
Earth Plate (5P)(For CE)(Option )
Interlock Safety Switch
1
1
1
45
T6-6-10980
Cable Gland (PG11)
(For TUV CE Version)(Option)
1
50
TE-097
2
4
1
2
4
4
4
4
8
2
4
4
2
4
PART NO.
DESCRIPTION
58
TMS0512
TMS0412
HB0620
TMS0408
PMS0425
PMS0520
PMS0410
PMS0410
FMS0508
59
60
PMS0412
SW04
61
63
SW06
SW05
Safety Limit Switch Ass'y
(For TP-201CE)
Safety Limit Switch Ass'y
(For TP-203CE)
Safety Limit Switch Ass'y
(For TP-201Y)
TMS, M5×12 (Option )
TMS, M4×12 (For CE)(Option )
HB, M6×20
TMS, M4×8 (Option )
PMS, M4×25 (Option )
PMS, M5×20
PMS, M4×10
PMS, M4×10 (For TP-201/TP-202)
FMS, M5×8 (For TUV CE Version)
(Option )
PMS, M4×12 (For TP-203)(Option)
SW, M4 (For TP-201/TP-202)
SW, M4 (For TP-203)(Option)
SW, M6
SW, M5
66
67
68
70
PW06C
PW05
HN06
HN04
PW, M6 (C)
PW, M5
HN, M6
HN, M4 (Option)
TE-100
TE-098
51
52
53
54
55
56
57
-34-
Q'TY
2
2
4
4
4
2
6
REMARKS
REF.
PART NO.
NO.
74 TMS0508
75 HN05
DESCRIPTION
76
PW04
TMS, M5×8
HN, M5
HN, M5 (For TUV CE Version)
(Option )
PW, M4 (Option)
80
81
82
PMS03.515
PMS0408
PW04
PMS, M3.5×15
PMS, M4×8
PW, M4
-35-
Q'TY
2
4
2
2
2
1
4
REMARKS
REF.
NO.
1
2
3
4
5
6
7
8
9
12
13
14
PART NO.
DESCRIPTION
Q'TY
16
19
20
21
22
23
24
TG-001
TG-002
TG-003
TG-004
TG-005
TG-006
T2-6-30250
TG-008
TG-009
TG-012
TG-013
T6-6-30133
T6-6-30034
TG-015
TG-015-1
TG-015-2
TG-016
TG-019
LA-10018
TG-021
TG-022
LA-40001
LA-40003
Power Switch
Variable Resistor (1MΩ)
Knob
Reset Push Button Switch
Feed Push Button Switch
Control Panel
PC Board
PC Board Receptacle
Base
Knob
Fuse Holder
Fuse (10A)(For 110V AC)
Fuse (7A)(For220V/230V/240V AC)
Transformer (For 110V)
Transformer (For 220V)
Transformer (For 240V)
Bolt
Power Cord
Label
Switch Cover
Grommet
Label
Label
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
30
34
LA-20170
TG-034
Label
Cover
1
1
51
52
53
61
62
63
64
TMS0408
HN04
TMS0312
TK-001
PW04
PMS0408
SW03
TMS, M4×8
HN, M4
TMS, M3×12
Main Power Switch (Only CE)
PW, M4
PMS, M4×8
SW, M3
8
2
2
1
2
2
2
15
REMARKS
02/2011
-37-