Project:
Type:
Quantity:
8-XPX SERIES
EXTERIOR END POLE MOUNT - EXTRUDED ALUMINUM - T5 LUMINAIRE
2009
PROGRESS
R e p o r t
Se
lection
Housing: Extruded structural aluminum.
Mounting: Pole - square or round. Mounts at fixture end.
Finish: Post powdercoat bronze housing & clear anodized lens
frame.
Distribution: Medium to wide. Replacement for low or highpressure sodium. *International Dark Sky Association Approved*.
Construction: Extruded aluminum housing & door frame.
Electrical: Electronic Standard or High output options; Program
Start Ballast is factory standard; <10% THD; Inherent thermal
protection.
Lens: ” thick tempered glass, polycarbonate or acrylic.
Lamping: Factory installation of lamps is strongly
recommended. Consult factory for pricing and specify CRI color.
Extruded structural aluminum housing - powdercoat
bronze is standard.
Specify other color on PO if required.
22
24
Nominal 13” x 24” long (not available with 5 or 6 lamps)
Nominal 13” x 48” long
Lamping
T5 = 54W, 24W or 28W, 14W per lamp.
Factory installed lamps are recommended.
LED = 5W or 25W per module. 1 lamp equates to 1 module.
Factory will install LED modules.
2
3
4
5
6
Ballast
S5
H5
LE
LH
(2) lamps(T5) / modules(LED) in cross section
(3) lamps in cross section
(4) lamps in cross section
(5) lamps in cross section
(6) lamps in cross section
All ballasts are 90°C
Standard Electronic T5 28W
High Output Electronic T5 54W
Standard LED 5W per module (up to 2 modules)
High Output LED 25W per module (up to 2 modules)
Lens
X
DESCRIPTION
G
P
A
Tempered Glass Lens ” thick
Clear Polycarbonate Lens ” thick
Clear Acrylic Lens ” thick
Voltage
SPEC. NOM.
U
H
Universal volt 120-277 (factory standard)
347-480 volt
Reflector
DESCRIPTION
E
W
Enhanced Aluminum 95% reflective
White Aluminum 90%+ reflective
Options
Dimension
Housing/
Finish
SPEC. NOM.
UL/CUL Listed. Wet Location. Sealed and Gasketed.
P
C
Photocell
Shunting Cap
See page 2 to order pole mounting kits.
Include the mounting kit part number on your purchase order
in addition to the fixture part number.
Include lamp CRI on purchase order for factory installed lamps.
ORDERING NOMENCLATURE GUIDE
Standard Fixture: 8-XPX244H5GUEP
Catalog # for a XPX Type Fixture – Extruded Aluminum Housing Powdercoated Bronze - Nominal 2 ft x 4 ft Long, 13” Wide Housing - 4 Lamps in cross section - High
Output T5 Electronic Ballast - Tempered Glass Lens - Universal Voltage - Enhanced Reflector - Photocell. Order mounting kits on page 2.
8A Product
Series
Housing
8-
XP
X
8A, an Alumen8 Brand
Dimension
Lamping
Ballast
Lens
2835 La Mirada Dr. Vista, CA 92081
PH: 760.727.7675
Page 1 of 1
Voltage
www.alumen8a.com
Reflector
Jan-10
Options
Project:
Type:
Quantity:
8-XPX SERIES
EXTERIOR END POLE MOUNT - EXTRUDED ALUMINUM - T5 LUMINAIRE
End Mount / Horizontal Round Pole Mount
End Mount / Factory Tilt Mount / Square Pole
Cobra Arm
Housing: Extruded structural aluminum.
Mounting: Pole - square or round. Mounts at fixture end.
Finish: Post powdercoat bronze housing & clear anodized lens
frame.
Distribution: Medium to wide. Replacement for low or highpressure sodium. *International Dark Sky Association Approved*.
Construction: Extruded aluminum housing & door frame.
Electrical: Electronic Standard or High output options; Program
Start Ballast is factory standard; <10% THD; Inherent thermal
protection.
Lens: ” thick tempered glass, polycarbonate or acrylic.
Lamping: Factory installation of lamps is strongly
recommended. Consult factory for pricing and specify CRI color.
UL/CUL Listed. Wet Location. Sealed and Gasketed.
Pole mounting kits must be ordered separately.
Please include quantity and part number on your purchase order along with your part number for the fixtures themselves.
Consult factory on all other mounting options.
SPEC. NOM.
DESCRIPTION
SPEC. NOM.
XPA-
Mount Style
MT-
End Mounting Kit
For an XPX or an XPA Fixture – End Mounted –
Aluminum Sheet Metal
Pole Type
Series
Kit Type
R
RT
F
FT
H
HT
DESCRIPTION
Horizontal Round Pole - parallel to ground - works w/ an
existing “cobra arm”.
Horizontal Round Pole - 15° tilt - works w/ an existing
“cobra arm”.
Horizontal Factory Mount - parallel to ground
Factory Tilt Mount - 15° tilt
Square Mount - choose when using sleeve
Square Tilt Mount - choose when using sleeve
---
Horizontal Round “Cobra Arm” - parallel to ground - no
designation needed. Choose “R” mount style.
VR
S
Vertical Round Pole - does not work w/ “R” mount
Square Pole
ORDERING NOMENCLATURE GUIDE
Standard End Mount Kit: MT-XPA-F-S
Catalog # for a XPX or XPA Type Fixture End Mount Kit, Constructed of Aluminum Sheet Metal – Horizontal Factory Mount - Square Pole
Quantity
8A, an Alumen8 Brand
Kit Type
Series
MT-
XPA-
2835 La Mirada Dr. Vista, CA 92081
PH: 760.727.7675
Page 2 of 2
Mount Style
www.alumen8a.com
Pole Type
Jan-10
Project:
Type:
Quantity:
8-XPX SERIES
EXTERIOR END POLE MOUNT - EXTRUDED ALUMINUM - T5 LUMINAIRE
12.5” housing
12.5”
3.315”
48”
13” with spring latch
PRODUCT NUMBER
= 8-XPX244H5GUE
FIXTURE EFFICIENCY
= 89.2%
S.M.H.
= 1.26
WATTAGE
= 212W
BASED ON 277V
RCR TABLE AVAILABLE
IES PHOTOMETRIC FILE AVAILABLE
SPECIFICATION CHARACTERISTICS
•
Medium to Wide Distribution Utilizing Energy Efficient Components Throughout
•
Highly Efficient Luminaire – Over 89% while Maintaining Wide Distribution with Uniform Illumination
•
Replaces Low Pressure Sodium, High Pressure Sodium and HID Pole Mounted Fixtures
•
The XPX is an IESNA Progress Report 2009 Award Winner, Recognized as “a Unique and Significant Advancement in the Art and
Science of Lighting”
•
T5 Application = 36,000 Hours (based on 12 hour starts), Lower Energy Consumption, 234W, No Color Shift, 85+ CRI Full Spectrum
Color, Instant-On, Programmed Rapid Start Ballasts are Standard
•
-20° Starting; Enhanced Cold Weather Performance Using the Amalgam Technology T5HO Lamp
•
LED Application = 60,000 Hours
•
*International Dark Sky Association Approved* with 90° Cut-Off
•
Photocell Sensor Option
•
Full Complement of Mounting Systems Available for All Manner of Pole Attachments
•
Finish: Rustproof Aluminum Extruded Structural Housing Post Powdercoated Bronze. Other Housing Finishes Available. Please
Contact Factory. Clear Anodized Extruded Aluminum Door Frame.
•
Multiple Lens Options: ” Thick Tempered Glass for Durability & Long Life; or Polycarbonate or Acrylic Lens
•
Innovatively Engineered Extruded Aluminum Door Frame with Ground-Breaking Integration of Door Hinge into the Extrusion
(patent pending)
•
Stainless Steel Over-Center Spring Latches for Tool-Less Entry: Meets DOT Requirements
•
Ultra-Thin Aerodynamic Profile to Minimize Wind Loading: 100 mph Rated for Fixed Pole Mount
•
Factory Installation of T5 Lamps is Highly Recommended
•
Short Lead Times
8A, an Alumen8 Brand
- Specify CRI on PO, lamps show separate on sales order but will be installed
2835 La Mirada Dr. Vista, CA 92081
PH: 760.727.7675
Page 3 of 3
www.alumen8a.com
Jan-10