Schedule of Rates for Vasco Retail Region
1. Quoted rate shall be applicable for any height, depth, level and thickness of wall etc unless
otherwise specified. Sales Building shall be generally ground floor and G+1 in some cases.
2. Samples of all materials will have to be approved by EIC before use. List of approved
make/brand is attached to technical/commercial bid. Decision of HPCL with regard to
selection of make/brand of material to be used shall be final.
3. All jobs to be carried out as per technical specification attached to technical/commercial
bid. All IS Codes referred to shall be of Latest Edition.
SR.
NO.
1
ITEM DESCRIPTION
SITE CLEARANCE
Surface dressing of the ground including removing small plants, bushes ,vegetation and making
surface levelled and disposal of rubbish outside HPCL's premises to an unobjectionable place,
as directed by the Engineer in Charge.
UNIT
SM
RATE
5.6
EXCAVATION IN EARTH UPTO 3 MET
Excavation for foundation upto required depth below existing ground level up to 3 m. depth in
any type of soil except hard rock . Rate to include dressing the sides and bottom, bailing out of
water if encountered, shoring, strutting, backfilling after the construction of foundation,
compacting by the side of the foundation and disposal of surplus excavated earth within/outside
HPCL's premises to an unobjectionable place, as directed by the Engineer in Charge including
spreading, watering and compaction, complete .
EXCAVATION IN EARTH 3 MTO 6M
Same as above but from 3 m. to reqr. Depth.
EXCAVATION IN HARD ROCK UPTO 3M
Description same as above item except the soil will be hard rock and excavation shall be done
by chiselling/ pneumatic drilling (Blasting is probhited)
EXCAVATION IN HARDRK 3M-6M
Same as above but from 3 m. to reqr. Depth.
SAND FILLING - LAYERS<150MM
Supply and filling with clean silver / river sand of approved quality in layers of 150 mm each
including spreading, compacting by hand ramming and watering etc, all complete as per
direction of Engg.-In-Charge. Measurement basis compacted thickness only.
EARTH FILLING- LAYERS<200MM
Supplying and filling imported earth of approved quality in layers not exceeding compacted
thickness of 200mm incl. Watering ,ramming, compacting, and if required, rolling and re-rolling
with power roller / manual roller / mechanical compactors to achieve maximum compaction, all
complete as per direction of Engg.-In-Charge. The earth should be free from weeds, grass and
other objectionable debris. Black Cotton soil shouldn't be used. Measurement basis compacted
thickness only. MDD and OMC tests shall be carried out and reports shall be submitted to EIC.
M3
115
M3
145
M3
530
M3
650
M3
700
M3
150
8
MURRUM FILLING- LAYERS<150MM
Supplying and filling imported murrum of approved quality in layers not exceeding compacted
thickness of 150 mm inclusive spreading, Watering ,ramming, compacting, and if required, rolling
and re-rolling with power roller / manual roller / mechanical compactors to achieve maximum
compaction, all complete as per direction of Engg.-In-Charge. The murrum should be excavated
from a quarry / mines, free from weeds, grass and other objectionable debris. Measurement
basis compacted thickness only. MDD and OMC tests shall be carried out and reports shall be
submitted to EIC.
M3
275
9
EARTH/MUR FILL AVAILABLE AT SITE
M3
62
2
3
4
5
6
7
10
11
12
13
14
15
16
17
18
19
20
21
22
Supplying and filling good quality earth/ murrum available at site in layers not exceeding
compacted thickness of 200mm incl. Watering ,ramming, compacting, and if required, rolling
and re-rolling with power roller / manual roller / mechanical compactors to achieve maximum
compaction, all complete as per direction of Engg.-In-Charge. The earth should be made free
from weeds, grass and other objectionable debris. Black Cotton soil shouldn't be used.
Measurement basis compacted thickness only. MDD and OMC tests shall be carried out and
reports shall be submitted to EIC.
PCC 1:4:8
Providing and laying PCC 1:4:8 using 40 mm and down size graded stone aggregates including
machine mixing, providing formwork if required, placing, compacting by hand ramming , curing
etc complete.
PCC 1:3:6
Providing and laying PCC 1:3:6 using 40 mm and down size graded stone aggregates including
machine mixing, providing formwork if required, placing, compacting by hand ramming, curing
etc complete.
PCC 1:2:4 FOR DPC
Providing and laying 50 mm thick DPC in PCC 1:2:4 mix with 6 to 12 mm size HBG aggregate in
two layers of 20 mm thick with two coats of hot bitumen (Grade A- 90/S-90 conforming to IS 73)
applied at rate 1.7 Kg per sq.mtr. over each layers as per specifications including cleaning,
watering ;the top surface of walls, centering, shuttering, placing, tamping, curing, sprinkling each
layer of dry and sharp sand over the hot bitumen etc. all complete as per drawing, Engineer-incharge direction.
RCC 1:2:4 FOR COPING
Providing and laying 60 mm average thickness coping in CC 1:2:4 mix using 6 to 12 mm stone
aggregate with 40 mm projection on either side of wall with drip mould. Rate to include 20 mm
thick plaster in cm 1:4 for fixing of glass pieces including mixing, providing necessary shuttering,
compaction and curing. Thickness of coping at the ends shall be 40 mm and 80 mm at centre .
M3
2240
M3
2605
SM
285
M3
3450
PCC 1:2:4 FOR GROUTING ANGLE
Providing and laying PCC 1:2:4 mix using 20mm to 12 mm stone aggregate including mixing,
providing necessary shuttering, compaction and curing etc complete.
RCC 1:1.5:3 FOR FOOTING
Providing , mixing and placing REINFORCEMENT CEMENT CONCRET 1:1.5:3 mix with
Ordinary Portland Cement using 20 mm and down size graded crushed aggregate including
providing and fixing necessary plywood /steel shuttering , scaffolding, machine mixing,
compacting by vibrators, curing, hacking the surface to receive plaster etc. complete. Rate shall
be exclusive of the cost of steel reinforcement, which will be paid under a separate item.
Concrete conforming to relevant specifications of IS 456 Latest Edn.
M3
3254
M3
4287
RCC 1:1.5:3 FOR COLUMNS/BEAMS
Same as above but for columns/beams
RCC 1:1.5:3 FOR CULVERT SLAB
Same as above but for culver slab
UR PILES 350MM DIA
UNDER REAMED PILES : Providing RCC 1:1.5:3 for under reamed piles up to required depth
with double bulbs as per IS 2911 etc. All complete. Pile cap and reinforcement steel shall be
paid separately. Size 350 mm diameter
UR PILES 300MM DIA
Same as above but size 300 mm diameter
UR PILES 230MM DIA
Same as above but size 230 mm diameter
REINFORCEMENT STEEL
Supply ,fabrication, hoisting and placing in position HYSD reinforcement bars conforming to
IS1786 -Latest Edition Grade FE 415 /TMT bars of same grade as per detailed drawing and
specifications including cutting, bending, cranking and tying with 18 SWG black annealed
binding wire complete. The rates shall be applicable for all heights and depths. Payment shall be
made as per reinforcement drawings and with theoretical weights only including all authorised
laps, chairs, spacers and hooks.
BRICK MASONRY SUBSTRUCTURE
M3
4688
M3
4800
MT
900
MT
798
MT
645
TM
46118
M3
2572
BRICK MASONRY WORKS :Providing and constructing following brick masonry in CM 1:5 using
first quality bricks of Class designation 35 (minimum) and conforming to IS-1077-1986 including
providing all openings and projections , raking the joints to 1 cm deep, scaffolding, soaking of
bricks in water prior to use and curing etc complete as per specifications . SUBSTRUCTURE:
Providing and laying brick masonry as above for foundation below DPC level.
23
24
BRICK MASONRY SUPERSTRUCTURE
Providing and laying brick Masonry as above but for superstructure above DPC level including
scaffolding.
PARTITION 115-BRICK MASONRY
Providing & laying brick masonry as above but for 115 mm thick in partition walls in CM 1:4. Rate
to include providing 75 mm thick RCC 1:1.5:3 bands using 2 nos 8 mm dia Torsteel
reinforcement at every 1 M height of wall including plywood/ MS shuttering. Steel reinforcement
shall be paid for separately.
M3
2706
SM
370
25
BRICK MASON WITH USED BRICKS
Providing and constructing brick masonry in CM 1:5 using used bricks. The bricks should be get
approved from the engineer in charge & should be cleaned from all dust & dirt prior to use. The
item includs providing all openings and projections , raking the joints to 1 cm deep, scaffolding,
soaking of bricks in water prior to use and curing etc complete as per specifications .
M3
1344
26
RRM SUBSTRUCTURE
Providing and constructing random rubble masonry with good quality stone in CM 1:5 for
substructure & superstructure as per IS 1597 part 1, latest edition. Rate to include soaking
stones, raking the joints to 1 cm deep and curing complete. One Through / Bond stone shall be
provided for every square meter of facing , evenly distributed in a staggered pattern. They shall
have about 0.03 sqm in face area and shall have a tailing for the full width of masonry upto
600mm.
If masonry wall is over 600mm thick, a line of headers (not less than 450mm length) overlapping
each other by 150mm shall be laid. Bond stones shall be distinctly marked on its face during
construction for verification. Quoin/key/corner stone shall not be less than 0.03 cum in volume.
M3
1719
27
RRM SUPER STRUCTURE
Same as above item but FOR SUPERSTRUCTURE including scaffolding
RUBBLE SOLLING 230 MM THK
Providing 230 mm thick rubble pitching including surface dressing, making required slope .
Rate to exclude flush pointing which will be paid for separately.
RUBBLE SOLLING – 150 MM THICK
Same as above item but for 150 mm thick
FLUSH POINTING
Providing flush pointing in rubble pitching with 1:3 cement mortar including curing etc. complete.
M3
1800
SM
156
SM
130
SM
63
RAISED POINTING
Providing raised pointing 12 mm with CM 1:3 along the joints of exposed stone masonry. The
joints shall be raked & cleaned, curing etc. all complete.
SUNKEN POINTING 12 MM
Providing sunken pointing 12 mm wide & 5 mm deep with CM 1:3 along the joints of exposed
stone masonry. The joints shall be raked & cleaned, curing etc. all complete.
CEILING PLASTERING 6 MM THK
SMOOTH CEMENT PLASTER FOR CEILING/CHHAJA Providing and applying 6 mm thick
plaster in CM 1:3 to ceiling and bottom surface of chajja using screened sand including finishing
smooth and providing drip moulds at chajja edges, scaffolding and curing etc. complete.
SM
73
SM
95
SM
105
34
SMOOTH PLASTERING 15MM THK FOR INT. WALL
Providing and laying 15mm thick smooth cement plastering in 1:4 CM in single coat to all the
interior walls including providing necessary scaffolding, chicken wire mesh at all joints of brick
and concrete surfaces, with a minimum overlap of 150 mm in all directions and additional
thickness if required to achieve perfect line and level without any extra cost.
SM
127
35
PLASTERING 20MM THK
SM
159
28
29
30
31
32
33
Providing and laying average 20 mm thick sand faced cement plaster as per following procedure
: Apply 12 mm thick coat of CM 1:4 mixed with CICO/ IMPERMO/ ACCOPROOF water proofing
compound mixed as per manufacturer's specifications as 1st coat and leaving the surface rough.
Apply 2nd coat of 8 mm thick of CM 1:4 and finishing the surface by rubbing with sponge till
uniform texture is obtained. Rate shall include providing necessary scaffolding, chicken wire
mesh.
36
37
38
39
40
41
42
43
44
45
46
47
48
49
WEEP HOLES
Providing, fabricating and installing in place, 75 mm dia PVC Pipes of various lengths & at
places as directed at site on the masonry wall for water drainage.
ST. STEEL - CLF/BWF
STRUCTURAL STEEL: ANGLE IRON POST : Supply, fabrication , erection and grouting of 65 x
65 x 6 ISA post and supporting angles of specified length in 1:2:4 concrete grout at every 2.4 m
C-C or as advised. Rate to include fabrication of the post as per the specification, erecting,
placing, grouting and painting of the posts with two coats of Synthetic Enamel over two coats of
Zinc Phosphate Primer Paints and primer shall be of SHALIMAR/ BERGER/ASIAN Make first
quality only.
MT
215
TM
57000
PIPE RAILING - CLF/BWF
PIPE RAILING : Supply and fixing of 40 NB medium quality MS pipes(IS 1239 latest edition) for
top and bottom railings to angle iron posts for fixing the edges of the chain link fencing. Rate
includes fabn, cutting, bending of the MS pipe, supply and fixing of MS clamps at every post,
with nuts and bolts(all proper sized) and painting the railing with two coats of Zinc Phosphate
Primer and two coats of Synthetic enamel paint after proper cleaning /scrapping .
SHALIMAR/BERGER/ASIAN make 1st quality only.
CHAIN LINK FENCING
CHAIN LINK FENCING : Supply and fixing of 50 x 50mm opening size 10 SWG GI chain link
fencing to the angle iron post with 8 SWG GI hooks and nuts and railing with 14 SWG GI
continuous wire (all details shall be as per enclosed drawing ) up to a height of 1.8 m from the
ground level. Rate to include unrolling the bundle, erecting, tightening and fixing at 300 mm C-C
on the vertical portion of the posts to every top and bottom railing with 14 gauge MS wire.
MT
370
SM
275
BARBED WIRE FENCING
BARBED WIRE FENCING Providing and fixing 13 rows horizontal and two diagonals with two
ply 12 SWG GI barbed wire fencing with barbes @ 100mm c/c . Angle iron post shall be paid
separately. For payment purpose measurement shall be taken for the lenth of plot boundary .
No measurement shall be taken for 13 rows individually.
HUME PIPES- 1000 MM DIA
HUME PIPE- Supplying, laying, joining and aligning 1000mm DIA NP3 class RCC Hume pipes
conforming to IS-458 Latest Edition below approach road as directed. Rate to include joining
with cement mortar, excavation up to required depth and providing and laying PCC 1:2:4
haunching @ 1m c/c , also including cutting, bending & supply and laying of 17 SWG annealed
binding wire inside the HUME Pipe for pulling cables in future.Test certificates from manufacture
shall be submitted and approved by EIC before use.1000 MM DIA
MT
215
MT
4760
HUME PIPES- 900 MM DIA
Same as above but size 900 mm dia
HUME PIPES- 600 MM DIA
Same as above but size 600 mm dia
HUME PIPES- 450 MM DIA
Same as above but size 450 mm dia
HUME PIPES- 300 MM DIA
Same as above but size 300 mm dia
HUME PIPES- 250 MM DIA
Same as above but size 250 mm dia
HUME PIPES- 200 MM DIA NP2 CLASS
Same as above but NP2 class & size 200 mm dia
HUME PIPES- 150 MM DIA NP2 CLASS
Same as above but NP2 class & size 150 mm dia
ANTI TERMITE TREATMENT
MT
4300
MT
3148
MT
2300
MT
750
MT
600
MT
500
MT
400
SM
77
ANTI TERMITE TREATMENT Providing anti-termite treatment including diluting and injecting
chemical solution/ Neem base solution and creating a continuous barrier under and alround the
column pits, wall trenches, basement excavation, top surface of plinth filing, junction of wall and
floor, along the external perimeter of building, expansion joints, over the top surface of
consolidated earth on which apron is to be laid, surroundings of pipes and conduits etc.
Complete as per specification using Clorpyriphous emulsified cocentrate (20%) in 1%
concentration ( or as recommended by the manufacturer) or using Neem based solution.
50
WHITE RECTIFIED TILES FOR COMP
Providing and fixing 1'x2' white color rectified tiles (approved shade and make ) of First quality ,
free from crack fissures & flakes with straight edge s & perfect corners fixed at right angles as
per the design and pattern, incldg. applying 8mm thick backing plaster in 1:4 CM and fixing the
tiles with neatcement paste, finishing the joints with white cement to match the colour of tiles
properly cured & finished in all respects etc. complete.
SM
900
51
CERAMIC TILE FLOORING 400mmX400mm
CERAMIC TILE FLOORING: Providing and laying (NITCO/KAJARIA/BELL/ H&R JOHNSON
MAKE)matt finish 1st quality Ceramic tiles of 6/8 mm thick of following size in flooring of
approved make and shade and free from cracks, warpage,fissures and flakes with straight
edges and perfect corner laid at right angle as per design and pattern over a bedding of cement
mortan of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching
colour pigment and finish in all respect and all material and labour complete. Size 400mm X
400 mm
CERAMIC TILE FLOORING 300mmX300mm
Same as above but size 300mmX300mm
VITRIFIED TILE FLRG. 400mmX400mm
POLISHED
VITRIFIED
TILE
FLOORING
:Providing
and
laying
1st
quality
(NITCO/KAJARIA/BELL/H&R JOHNSON MAKE)polished vitrified tiles of 8 mm thick of
followg.sizes on flooring (approved make&shade, free from cracks, warpage,fissures and
flakes, straight edges and perfect corner) laid at right angle as per design and pattern over a
30mm bedding of cement mortar(CM 1:5), finishing the joints neatly with white cement mixed
with matching colour pigment and finish in all respect and all material and labour complete.
SM
662
SM
605
SM
1300
VITRIFIED TILE FLRG. 300mmX300mm
Same as above but size 300mmX300mm
VITR.TILE 600X600SALT PAPER GRAY
Providing and laying 1st quality polished vitrified tiles of 8 mm thick 600X600 size in flooring of
approved make and shade and free from cracks, warpage,fissures and flakes with straight
edges and perfect corner laid at right angle as per design and pattern over a bedding of cement
mortan of 30 mm thick CM 1:5 finishing the joints neatly with white cement mixed with matching
colour pigment and finish in all respect H&R JOHNSON( Marbonite) make SALT PEPPER
GRAY FINISH , SIZE: 600 X 600 mm or approved equivalent from NITCO.and all material and
labour complete as per the direction of Engineer In Charge .
SM
1000
SM
1570
VITRIFIED TILE 600X600 SINTRA
Same as above but H&R JOHNSON( Marbonite) make SINTRA FINISH or approved equivalent
from NITCO
VITRFIED SNOW CARARA 3'X3' (900x900)
Same as above but size 900mmX900mm & H&R JOHNSON( Marbonite) make SNOW CARARA
FINISH or approved equivalent from NITCO
VITRIFIED OLYMPUS 600X600
Same as above but size 600mm X 600 mm &H&R JOHNSON( Marbonite) make OLYMPUS
finish or approved equivalent from NITCO.
VITRFIED SAVONA -600X600
Same as above but size 600mmX600mm & NITCO make SAVONA finish or approved equivalent
from H&R JOHNSON.
VITRIFIED OCEAN MIST-1000X1000
Same as above but size 1000mmX1000mm & NITCO make OCEAN MIST Finish or approved
equivalent from H&R JOHNSON
VITRIFIED NOVARA BIEGE-800X800
SM
1570
SM
1931
SM
1450
SM
1450
SM
1931
SM
1850
52
53
54
55
56
57
58
59
60
61
Same as above but size 800mmX800mm & NITCO make NOVARA BIEGE finish or approved
equivalent from H&R JOHNSON
CERAMIC TILE CREAMA ROYAL
Providing and fixing ceramic tiles of 300 x 600 mm size & 5 mm thick CREMA ROYAL From HR
JOHNSON Only) ) First quality , free from crack fissures & flakes with straight edge s & perfect
corners fixed at right angles as per the design and pattern, incldg. applying 12mm thick backing
plaster in 1:4 CM and fixing the tiles with neatcement paste, finishing the joints with white
cement mixed with colouring pigments to match the colour of tiles properly cured & finished in all
respects etc. complete.
SM
780
CERAMIC TILE RIVIERA
Same as above but Riviera finish from NITCO
TERRACOTTA TILES
Terracotta Tiles:Providing and fixing terracotta tiles minimum 3 mm thick and minimum 75x150
mm size of approved shade and make First quality , free from crack fissures & flakes with
straight edges & perfect corners fixed in true line & level as per the design and pattern advised
by Engg.-In-Charge. Rate includes applying 12 mm thick backing plaster in 1:3 CM in true line &
level, properly cured & rough finished. Fixing the tiles with neat cement paste and finishing the
joints with terracotta paint in a neat & aesthetic way complete in all respects. Approved Make of
Tiles: Dazzle Designer Tiles of Milan - Terracotta smooth finish
SM
780
SM
750
65
MANGLORE TILES ON ROOF/CHAJJA
Providing and fixing Mangalore tilesof 12 mm thick and minimum 230x150 mm size of approved
shade and make First quality , free from crack fissures & flakes with straight edges & perfect
corners fixed in true line & level as per the design and pattern advised by Engg.-In-Charge and
finishing the work in a neat & aesthetic way complete in all respects. Rate to include Teakwood
framing structure for holding the tiles in fixed condition.
SM
750
66
MOSAIC TILES OF NITCO
MOSAIC TILES FROM NITCO: Supply and fixing mosaic tiles of NITCO make RY36S and GY
36S in pattern including providing 1:5 CM bed and floating coat of neat cement slurry finishing
the joints with white cement , mixed with matchinmg colour pigments, cleaning the surface with
dilute sulfuric acid etc complete.
MOSAIC TILES OF LOCAL MAKE
Supply and fixing mosaic tiles of local make similar to Nitco-RY36S and GY 36S in pattern
including providing 1:5 CM bed and floating coat of neat cement slurry finishing the joints with
white cement , mixed with matchinmg colour pigments, cleaning the surface with dilute sulfuric
acid etc complete.
SM
1017
SM
550
GRANITE TILE FLOORING
GRANITE TILE FLOORING Providing and laying 10 mm thick granite tile of size of 300 mm x
300 mm in flooring of approved shade and free from cracks, warpage,fissures and flakes with
straight edges and perfect corner laid at right angle as per design and pattern over a bedding of
30 mm thick 1:5 cement mortar and neat cement slurry, finishing the joints neatly with white
cement mixed with matching colour pigment and finish in all respect and al l material and labour
complete.
IPS FLOORING
IPS FLOORING Providing mixing and laying 50 mm thick Indian Patent Stone flooring in PCC
1:2:4 mix concrete with 12 mm and down size graded crushed aggregate including providing
and fixing 4 x 25 mm size glass strips in 1 metre x 1 metre panels, casting the concrete
compacting and finishing the surface smooth using cement slurry.
GRANITE SKIRTING
GRANITE SKIRTING Providing and fixing 10mm thick jet black granite skirting of 100 mm
hight free from crack fissures & flakes with straight edges & perfect corners fixed at right angles
with neat cement paste and finishing the joint with white cement mixed with matching colour
pigment .
CERMIC TILE DADO
SM
1550
SM
209
MT
180
SM
630
62
63
64
67
68
69
70
71
CERAMIC TILES DADO IN TOILET: Providing and fixing ceramic tiles of 300 x 200 mm size
(approved shade and make )First quality , free from crack fissures & flakes with straight edge s
& perfect corners fixed at right angles as per the design and pattern, incldg. applying 12mm
thick backing plaster in 1:4 CM and fixing the tiles with neatcement paste, finishing the joints
with white cement mixed with colouring pigments to match the colour of tiles properly cured &
finished in all respects etc. complete.
72
73
74
75
76
77
78
BORDER TILE
Same as above but laying and fixing designed border tile.
GRANITE SLAB 18 MM BLACK COLOUR
18MM THICK GRANITE CLADDING FOR CURTAIN WALL Providing and fixing machine cut
and polished black Granite slab of thickness of 18 mm selected & sorted for uniformity in
colour, free from cracks, fissures and flakes with straight edges and perfect cornors using
50mmx20mmx3mm SS T shaped cleats of 100mm long . The cleats are fixed over the wall with
M12x100mm long GI fasteners by providing 2 nos 12mmx25mm size slots and drilling the wall.
Rate to include making necessary grooves in granite slab.
SM
700
SM
2888
HP LOGO FIXING
Fixing of HPCL Logo Box in line and level on the Granite curtain wall with the help of necessary
fasteners.
KOTA STONE FLOORING
KOTA STONE FLOORING Providing and laying 20mm thick Kota Stone flooring using machine
cut and machine polished tiles of uniform colour and approved size and pattern including
bedding of 30mm thick CM1:3 close jointed and floated with matching cement slurry laid to level
as required, curing machine polishing with oxalic acid to achive mirror finish etc., complete.
EA
900
SM
775
MT
130
SM
800
SM
2617
KOTA STONE SKIRTING
KOTA STONE SKIRING Providing and laying 125mm high x 18mm thick Kota stone skiring on
the walls in uniform colour and approved size & pattern including bedding of 20mm thick CM1:3
close jointed & floated with matching cement slurry, curing, polishing to mirror finish with oxalic
acid etc., complete.
KOTA STONE STEPS
KOTA STONE STEPS Providing and fixing 20 mm thick one piece Kota stone slabs with 25mm
bedding CM 1:3, cement slurry and machine polishing on one side for risers of steps, treads
and shelf slab including nosing etc . complete
GRANITE SILL SLAB FOR WINDOWS
SILL SLAB Providing and laying 18 mm thick machine cut & machine polished jet black granite
strips over a bedding of 18 mm thick 1:5 CM for window sills. The strips shall be of single piece
only as per width of window wall and project 12 mm beyond the face of the wall.
79
EUROCON TILE-WALKWAY NLT 500
Supply and fixing concrete tile of EUROCON make of approved shade of 20mm thickness for
flooring including providing 20mm thick 1:5 cement mortar bed and a floating coat of neat
cement slurry, finishing the joints with white cement mixed with matching colour pigment,
cleaning the surface with dilute sulphuric acid etc. Complete. If necessary, surface unevenness
shall be filled up with brick ballast manually compacted with watering etc. complete as per
instructions of Engg.-In-Charge without extra cost. Basic rate : Not lower than Rs. 500/sqm.
SM
1050
80
EUROCON TILE-WALKWAY NLT 400
Same as above item but for treads and risers Basic rate: Not lower than Rs. 400/sqm
WATER PROOFING BY BITUMEN FELT
Water proofing with bitumen felts as per specifications (Bitumen of Shalimar or equivalent make
as approved by EIC)- Scrapping, removing old bituminised surface, if any, by chisel, etc,
cleaning the surface thoroughly with wire brush and duster and providing water proofing as per
specification. Applying one coat of bitumen primer, applying hot bitumen 30/40 @ 1.2kg/SQM.
Supplying and laying bitumen felt conforming to IS:1322 in lengths at right angles to the direction
of the run of the gradient, starting at the lowest level and overlap of 75mmfor adjacent layers,
overlap at end of strip of felt should be 100mm. Parapet joints to be suitably fillated and the feltto
to be taken upto a minimum heuight of 225mm on the parapet. Scope of job includes breaking of
parapet plaster upto min 225mm making chases before the felto and finally plastering the
surface upto the felto height.
SM
950
SM
363
BRICKBAT TERRACE WATER PROOF.
SM
370
81
82
BRICKBAT COBA ON TERRACE Providing and laying integral cement based water proofing of
average 100 mm thick as per specifications given. The job includes Cleaning of RCC slab and
applying neat cement slurry mixed with waterproofing compound, providing and laying brickbat
coba in CM 1:4 mixed with water proofing compound and curing for a period of 24 hours, laying
of 25 mm thick PCC 1:1.5:3 mix with 6 mm and down size coarse aggregate and water proofing
compound, finishing smooth, making half round vata at the junction of parapet wall and slab and
curing for 10 days. NOTE:- Contractor to submit a guarantee in respect of performance of
waterproofing ,for 10 years on a Stamp-paper. Further , @10% of job amount shall be retained
for 2 years as retention money , returnable after retention period without interest . Approved
brands of waterproofing compound are : CICO/ACCOPROOF/IMPERMO.
83
84
CHAJJA WATER PROOFING
Water proofing on top of chhaja with 25mm thick PCC 1:1.5:3 with 6mm and down size stone
aggregate mixed with water proofing compound, finishing smooth, making half round vata at the
junction of chhaja and wall , curing etc. complete.
WHITE WASH
All material required for execution of painting work shall be obtained direct from approved
manufacturers and shall be brought to the sites in their drums / cans / bags etc with seals
unbroken. No thinner shall be used unless approved by Engg.-In-Charge. The paint shall be
applied by using brush, roller or spraying as directed. The paint etc shall be applied only after
proper surface preparation by removing all dirt, dust, mortar droppings, another foreign matter,
loose scale by using brooms, wire brush, sand paper etc as per requirement and direction
complete. All holes, cracks, patches etc shall be made good with material similar to that of the
surface. The painting shall be applied in specified coats or more so as to obtain the desired
finish. If additional coats are required to obtain uniform and smooth finish, the same shall be
carried out at no extra cost. The job includes provision of scaffolding using safety precautions,
curing etc as required.
SM
240
SM
12
WHITEWASH Providing and applying 3 coats of white wash to plastered and concrete surfaces
including providing necessary scaffolding, surface preparation , mixing DDL binder, blue etc.
complete as per IS: 712- Latest Edition. If additional coats are required to obtain uniform and
smooth finish, the same shall be carried out at no extra cost.
85
OIL BOUND DISTEMBER
OIL BOUND DISTEMPER Providing and applying 2 coats ( first coat with brush and final coat
with Roller) of OBD of approved make and shade on all surfaces and heights to give an even
shade including primimg coat and full putty after thoroughly brushing the surface free from
mortar dropping and other foreign matter and also including preparing the surface even and
sand papered smooth etc., all material and labour complete. General specifications/guidelines
given under WHITEWASH item also to be followed, as applicable.
SM
49
86
ACRYLIC EMULSIONPAINT(INT/GRD)
ACRYLIC EMULSION PAINT (INTERIOR GRADE) Providing and applying 2 coats ( first coat
with brush and final coat with Roller) of Acrylic Emulsion paint of approved make and shade on
all surfaces and heights to give an even shade including primer and full putty after thoroughly
brushing the surface free from mortar dropping and other foreign matter and also including
preparing the surface even and sand papered smooth etc., all material and labour complete.
General specifications/guidelines given under WHITEWASH item also to be followed, as
applicable.
SM
88
87
ACRYLIC EMULSIONPAINT(EXT/GRD)
ACRYLIC EMULSION PAINT (EXTERIOR GRADE) Providing and applying 3 coats of acrylic
anti fungal cement paint including primer of BERGER (Weathercoat) or approved equivalent
make and shade to all the exterior surfaces as per manufacturer's specifications including
providing necessary scaffolding, curing , etc. complete. If additional coats are required to obtain
uniform finish, the same shall be carried out at no extra,cost as directed by Engineer In Charge.
General specifications/guidelines given under WHITEWASH item also to be followed, as
applicable.
APEX PAINTING
SM
95
SM
105
88
APEX PAINTING : Providing and applying 2 coats of Apex paint to all the exterior surfaces
including a coat of primer as per manufacturer's specification complete. General
specifications/guidelines given under WHITEWASH item also to be followed, as applicable.
PLASTIC EMULSION PAINT
PLASTIC EMULSION PAINT: Providing and applying 2 coats ( first coat with brush and final coat
with Roller) of Plastic Emulsion paint of approved make and shade on all surfaces and heights
to give an even shade including primer and compatible putty. Approved Make: Asian/Nitco /
Nerolac. General specifications/guidelines given under WHITEWASH item also to be followed,
as applicable.
WATER PROOF CEMENT PAINT
WATER PROOF CEMENT PAINT Providing and applying 2 coats of snowcem to plastered
and concrete surfaces including providing necessary scaffolding, surface preparation etc.
complete. If additional coats are required to obtain uniform and smooth finish, the same shall be
carried out at no extra cost. General specifications/guidelines given under WHITEWASH item
also to be followed, as applicable.
SANDTEX MATT
SANDTEX MATT Providing and applying 2 coats of Sandtex matt paint of SNOWCEM INDIA
make and of required shades on all surfaces and heights to give an even shade including
primer coat of snowcem plus. General specifications/guidelines given under WHITEWASH item
also to be followed, as applicable.
SY. ENML. PAINT OVER WALL
SYNTHETIC ENAMEL PAINT OVER WALL Providing and applying 2 coats of synthetic enamel
paint 1st quality of approved manufacturer and of required shades on wall to give an even
shade including a primer coat. General specifications/guidelines given under WHITEWASH item
also to be followed, as applicable.
SM
85
SM
46
SM
75
SM
65
SY.ENML.PAINT OVER STEEL/WOOD
SYNTHETIC ENAMEL PAINT OVER STEEL/WOOD SURFACE Providing and applying 2 coats
of synthetic enamel paint 1st quality of approved manufacturer and shades on steel surface
to give an even shade including two coats of red oxide primer. General specifications/guidelines
given under WHITEWASH item also to be followed, as applicable.
POP PUNNING
ON WALL & CEILING : Providing and applying Plaster of Paris(POP) punning on walls, ceilings,
beams and columns to bring the surface in plumb line and level including making the surface
smooth etc. complete. The rate shall include preparing the surface with POP and compatible
putty to give a smooth finish as per approval of the Engg.-In-Charge. Rate to include cost of
scrapping, neuro finish etc. complete if needed.
SM
70
SM
85
95
POP -MOULDING
Plaster of Paris (POP) Moulding : Providing and fixing moulding of size 3" x 3" in the edge of the
wall and the ceiling with necessary hardware, properly finished, all material and labour complete.
MR
146
96
MS GRILL
Supply, installation and fixing of Prefabricated MS grill (IS 2062 Latest Edition) using MS
flat/structurals / bars / hollow sections / strips / pipes etc as per design given by HPCL and
direction of Engg.-In-Charge. Rate to include erection, grouting of posts in PCC 1:1.5:3, painting
by two coats of red oxide primer and two coats of synthetic enamel of approved shade. Grouting
PCC to be paid separately as per relevant item.
KG
58
97
MS LADDER
Supply, installation and fixing of Prefabricated MS Ladder/ Stair case/ baluster/ MS Bars (IS
2062 Latest Edition) using MS flat/structurals / bars / hollow sections / strips / pipes etc as per
design given by HPCL and direction of Engg.-In-Charge. Rate to include erection, grouting of
posts in PCC 1:1.5:3, painting by two coats of red oxide primer and two coats of synthetic
enamel of approved shade. Grouting PCC to be paid separately as per relevant item.
KG
57
98
ANOD.AL.GLZ. DOOR-12MM GLASS
SM
3120
89
90
91
92
93
94
ALUMINIUM GLAZED DOOR/ FIXED GLAZING WITH 12MM GLASS: Providing and fixing
Aluminium glazed door/ fixed glazing with 25 micron coloured anodised aluminium section
minimum wall thickness of not less than 2 mm with extruded built up section of approved make
and weight ratio joints mitred ad joint with heavy duty aluminium pressure die cast cleats with fins
to match the section of frames conforming to approved section and shutter conforming to
approved sections and glazed with 12 mm thick glass fixed to shutter with AL snap beading and
neoprene /PVC gaskets/CP brass/Stainless steel screws and fixed to the wall with requisite rawl
plugs and screw or with fixing clips or with expansion hold fasteners incldg. required filling up of
gaps at junctions,top ,bottom ,sides with PVC/Neoprene felt/Polysulphide sealant/silicon sealant
all complete as per advise. Al-anodised shop front (Doors & fixed glazing) with frames at top &
bottom and at two ends of JINDAL or equivalent approved make with section no. 9205 of size
101.5X44.45X3 with weight of 2.342 Kg/M.
Round acrylic handle and locking arrangement to be provided for main door.
The glass should be single piece only. All glass edges shall be grinded and polished smooth as
per instructions. The floor spring strut shall be fixed and accommodated in Aluminium section
groove. In case of non-availability, approved equivalent make for Al sections is JINDAL.
Approval of Engg.-In-Charge shall be taken before using equivalent sections matching next
higher dimensions and weight per running metre without extra cost. Approved Make of Glass:
AIS, Modi, Saint Gobain, Triveni
99
100
101
102
103
AL. GLZ. DOOR/FIXED GALZING-12MM TOUGH.GLASS
Same as above but with 12 mm toughened glass.
PDR.COAT.AL GLZ. DOOR/FIXED GALZING-12mm…
With Powder Coated aluminum section of approved colour having coating thickness of minimum
50 micron with 12mm plain glass and all specification same as item above
PDR.COAT.AL GLZ. DOOR/FIXED GALZING-TOUGH….
Same as above but with 12 mm toughened glass.
HY. FLOOR SPRING
HYDRAULIC FLOOR SPRINGS Providing and fixing double action hydraulic floor springs of
approved brand ( HARDWYN / EVERITE/ SANDHU) conforming to IS 6315 : 1992 for
aluminium doors. Rate to include cutting of floors as required, embedding in floors and cover
plates etc complete as per specifications. Load Capacity = 61-80 kg
SM
4267
SM
3215
SM
4400
EA
2300
AL. PANELLED DOOR
ALUMINIUM PANELED DOOR : Providing and fixing 15 micron colored anodised single leaf
aluminium door with minimum wall thickness of not less than 2 mm , joints mitred and jointed
with heavy duty aluminium pressure die cast cleats with fins to match the outer frames and door
frames conforming JINDAL sections as specified fully paneled with 9 mm thick pre-laminated 3
layers medium density ( exterior grade) particle board Grade-1, type -II conforming to IS:12823
bonded with phenolformaldehyde synthetic resin of approved brand and manufacturer fixed to
shutter with aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel
screws fixed to the wall with requisite rawl plugs and screw or with fixing clips or with expansion
hold fasteners including necessary filling up of gaps at junctions, at top , bottom and sides with
requisite PVC/neoprene felt/polysulphide sealant/silicon sealant including hard ware such as
tower bolt of 150 mm length from inside and Aluminum handle and Aluminum aldrop of 200 mm
length
SM
3040
SM
2656
on both sides, 3 nos. Aluminium hinges of 100 mm length etc all complete as per architectural
drawing. Aluminium door section of JINDAL make or equivalent make with the following section :
Main frame on all sides - 4700 -101.6 x 44.45 x 2.5 of weight 1.977 kg/m Shutter vertical frame4537 - 53.7x44.45x2.3 of weight 1.238 kg/m. Shutter top frame - 4540 - 53.7x44.45x2.3 of weight
1.173 kg/m.
Shutter middle frame - 4621 - 49.91x44.45x3 of weight 1.495 kg/m Shutter bottom frame - 4524 83.5x44.45x3 of weight 2.107 kg/m, aluminium Cast Door handle and Clip - 4420 - 19x17.3x0.9
of weight 0.124 kg/m. In case of non-availability, approved equivalent make for Al sections is
HINDALCO. Approval of Engg.-In-Charge shall be taken before using equivalent sections
matching next higher dimensions and weight per running metre without extra cost.
104
AL. WINDOWS OPENABLE
ALUMINIUM WINDOWS (OPENABLE) : Providing and fixing 15 micron colour anodised/ powder
coated aluminium glazed windows with 5 mm glass & extruded built up section of wall thickness
not less than 1.4 mm and approved make with glass panel fixed to side -hung shutter with
aluminium snap beading and neoprene / PVC gasket / CP Brass /stainless steel screws fixed to
the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fasteners
including necessary filling up of gaps at junctions at top , bottom and sides with requisite PVC /
neoprene felt / polysulphide sealant/silicon sealant including heavy duty handle cum locking
arrangement etc all complete as per architectural drawing and the direction of Engg.In-charge.
105
AL. SLIDING WINDOWS 3 TRACK
Same as above but Aluminium sliding windows of Jindal make shutter sections: Top & Bottom 8820- 1.5 mm thick @ 0.547 kg/m; Handle Section 8822- 1.5 mm thick @ 0.547 kg/m; Shutter
Interlock 8821- 1.45 mm thick @ 0.607 kg/m. Rate includes wheels/bearings, interlocking
arrangements etc. complete. The track section shall be as follows:
Two Track Window: Top & Side - 8931-1.5 mm thick @ 0.784 kg/m; Bottom (Bulb) - 8932- 1.5
mm thick @ 0.909 kg/m
SM
2600
106
AL. SLIDING WINDOWS 2 TRACK
Same as above Item but Two Track Window: Top & Side - 8933-1.5 mm thick @ 1.06 kg/m;
Bottom (Bulb) - 8934- 1.5 mm thick @ 1.248 kg/m
AL. LOUVERED VENTILATOR
ALUMINIUM LOUVERED VENTILATOR : Providing and fixing 15 micron colour
anodised/powder coated aluminium ventilator with extruded built up section of wall thickness
not less than 1.5 mm and approved make glazed with 5 mm thick opaque glass louver 100mm
wide.
AL.GL.DOOR/FIXED GLZ 6mm THK
ALUMINIUM DOOR/FIXED GLAZING WITH 6 MM GLASS : Providing and fixing 15 micron
coloured anodised aluminium fixed glazing/aluminium door with 6 mm glass extruded built up
section of wall thickness not less than 1.5 mm and approve make with glass panel fixed with
Aluminium snap beading/ Neoprene / PVC gasket/CP Brass /stainless steel screws and fixed to
the wall with requisite rawl plugs and screw or with fixing clips or with expansion hold fasteners
including necessary filling up of gaps at junctions, at top , bottom and sides with requisite PVC /
neoprene felt/ polysulphide sealant/silicon sealant all complete as per architectural drawing and
the direction of Engg. In-charge. Aluminium section of JINDAL make or equivalent make with
the following sections : Outer frame sections - 4688- 63.5x38.1x1.65 of weight 0.942 kg/m.
Intermediate frame - 4687- 63.5x38.1x1.53 of weight 0.942 kg/m. Glass panels used shall not be
less than 2.4 m (height) x 1.2 m (width). All the joints shall be provided with Aluminium sections
as specified.
SM
2550
SM
1955
SM
2522
SM
2095
SM
2095
107
108
Door:
Outer side frame - 4550 - 47.62x44.45x1.52 of weight 0.881 kg/m.
Bottom frame - 4553 - 95.25x44.45x1.70 of weight 1.301 kg/m
Intermediate frame - 4621- 49.91x44.45x1.60 of weight 0.882 kg/m.
Clip- 4420- 19x17.3x0.9 of wt. 0.124 Kg/m.
The floor spring strut shall be fixed and accommodated in Aluminium section groove. The door
shall be provided with die cast aluminium handle, towerbolt, locking arrangement etc. complete.
The joints and gaps shall be treated with silicon sealant to stop water ingress and glass surfaces
shall be cleaned neat of left over sealant. Approved Make of Glass: AIS, Modi, Saint Gobain,
Triveni. In case of non-availability, approved equivalent make for Al sections is JINDAL.
Approval of Engg.-In-Charge shall be taken before using equivalents matching next higher
dimensions and weight per running metre without extra cost.
109
110
STEEL WINDOWS
STEEL WINDOWS : Supply, fabrication and fixing of MS glazed windows using approved Z
sections with 5mm plain glass including providing grill with 12mm square bar @100mm c/c ,
painting with two coats of red oxide primer and two coats of synthetic enamel paint, handle , stay
arrangement etc. complete.
STEEL DOORS
111
112
113
114
STEEL DOORS : Supply, fabrication and fixing of MS Door using 35x35x5 angle frame and
25x25x3 angle members including bracings with 16 gauge MS sheet stitch welded to Door
shutter frame complete as per direction of Engg.-In-Charge painting with two coats of red oxide
primer and two coats of synthetic enamel paint, handle , stay arrangement ,tower bolt etc.
complete.
FLUSH DOOR Providing and fixing solid core flush door in single leaf 35mm thick commertial
plywook of seasoned wood without ventilator. Door frame to be made of 60mm x 100mm teak
wood with wrough iron hold fasts. Door to be fitted with brass fitting-hinges, handles on both
sides, tower bolts, etc., complete. Frame to be painted in three coats of synethic enamel paint
over a coat of wood primer including scrapping, surface preparation etc., complete.Door(leaf) to
be laminated on both sides with laminations 1.5 mm thk and grey in color of approved
make/brand.Approved Make: Kitply/ Anchor Board/ Wonder wood/ Duro/ National or approved
equivalent.
FLUSH DOOR 900x2100mm:
Providing and fixing solid core flush door in single leaf 35mm thick commertial plywook of
seasoned wood without ventilator. Door frame to be made of 60mm x 100mm teak wood with
wrough iron hold fasts. Door to be fitted with brass fitting-hinges, handles on both sides, tower
bolts, etc., complete. Frame to be painted in three coats of synethic enamel paint over a coat of
wood primer including scrapping, surface preparation etc., complete.Door(leaf) to be laminated
on both sides with laminations 1.5 mm thk and grey in color of approved make/brand.Approved
Make: Kitply/ Anchor Board/ Wonder wood/ Duro/ National or approved equivalent. Size
900X2100mm
FLUSH DOOR 750x2100mm
Same as above but size 750X2100mm
ROLLING SHUTTER
ROLLING SHUTTER Supply, fabrication and fixing of MS rolling shutter of the following
specifications including grill window of 300 mm height at eye level for visibility even in closed
position. Code: Conforming to IS 6248 – 1979 Type: Self Coiling type (manual) Curtains:
Interlocking cold rolled lath section of 0.8 mm thickness. Lock plate : MS sheet of 3.15 mm thick
reinforced with MS angles of 35 x 35 mm. Guide channel : MS sheets of 3.5 mm thick Bracket
Plate : MS Sheet of 0.9 mm thick. Hood Covers : MS sheet of 0.9 mm thick Locking handle : To
be provided suitably. Rate shall include providing and fixing holdfasts and painting two coats of
enamel paint of approved make and shade over two coats of zinc phosphate primer. Shutter up
to 10 SQM -push pull type hand operated with ball bearings , For 10 SQM upto 30 SQMMechanical operated gear type with ball bearing, a pulling hook shall be provided for each of the
rolling shutter.
GRILL IN ROLLING SHUTTER
GRILL IN ROLLING SHUTTER : Supply, fabrication and fixing of manually operated steel rolling
net shutter as per the specification. Nets to be in hexagonal pattern, The round MS bars used for
jali should be 8mm in dia . All other specification as that of item for rolling shutter above.
EA
7605
EA
7400
SM
2200
SM
2400
115
DISPLAY SHELF
DISPLAY SHELF: Providing & fixing in position 12 mm thick plain glass of Modi/AIS/Saint
Gobain/Triveni make with polished edges in the grooves between the 25 mm thick exterior grade
MDF board planks at 325 mm c/c & 350 mm wide. The MDF board shall be fixed on teak wood
frame fixed to the wall using plugs, screws and holdtights. Cross section of teak wood shall be
50x75 mm. The teak wood shall be seasoned and brushed with anti-termite chemical before use.
Teak wood framing shall be fixed over wall in such a way that it forms grids of size 450x325 mm
so as not to obstruct the grooves. The exposed surface of the MDF board shall be finished with
1.5 mm thick lamination of approved colour & combination of colours with teak wood beadings
on edges. The approved brand for the lamination shall be Formica/Greenlam / Sundek.
SM
3090
116
STORAGE & SHELVES
Specifications as above item but with storage at bottom, as per the standard drawing.
MS FAN HOOKS
FAN HOOKS : Providing & fixing MS fan hooks with 16 mm dia MS bar bent to shape with
hooked ends in RCC Slab during laying including painting the exposed portion.
MORTICE LOCK
SM
3320
EA
73
EA
900
117
118
119
120
121
122
123
124
MORTICE LOCK Providing & fixing GODREJ make only six lever lock ( Cylindrical/ Round Head
) including all necessary hardware etc.
DOOR CLOSER
DOOR CLOSER Providing and fixing door closer of Hardwyn / Everite make size no. 2.
STRUCT STEEL FOR SERVICE BAY
Supplying , erecting and fixing in position Pre- fabricated structures at all elevations for service
bay using structural steel sections conforming to IS:2062 , including cutting, welding or bolting,
supply of bolts/nuts/washers etc., complete as per drawings including surface preparation and
applying one coat of Zinc Phosphate Primer before erection and two coats of synthetic enamel
paint as per specification after erection and all materials and labour complete. ( No welding is
permitted at site). The rate quoted shall include cost of bolts, nuts, washers, welding and
electrodes and any other consumables required for completing the work. The bolts , nuts ,
washers, welds etc shall not be separately measured and paid for.
AC SHEET FOR ROOF
Supply , erection and fixing of corrugated asbestos cement sheet of Everest make or approved
equivalent for service bay including supply and fixing of bitumen/GI washer, J bolt etc. For
Roof
AC SHEET FOR SIDE
Same as above Item but for side sheet including gable end.
BARRICADING
Providing & Fixing in position 8' HT GI sheet ( 22 swg) with angle support (50x50x5 mm ) at
every 2.4 m c/c and horizontal support of 40x40x5 angle at equal distance for 8' ht &. The Job
includes grouting vertical angle supports in RCC 1:2:4, fixing the sheets with necessaru J hooks,
painting with synthetic enamel paint in Yellow and Black strip combination, and dismantling &
disposing off the entire material after completion of work.
GY. BOARD FALSE CEILING
Providing and fixing Gyp board false ceiling with required accessories INDIA GYPSUM make
including painting with two coats of plastic emulsion paint. 12.5 mm thick 'Gypboard' shall be
screw-fixed to the underside of suspended GI grid. GI grid shall be installed as per
manufacturer's specifications. GI grid shall consist of ceiling sections (India Gypsum Code no.
MF5) at maximum c/c distance 450 mm, Perimeter channel (India Gypsum code no. MF6A),
intermediate channels (India Gypsum code no. MF7) at maximum c/c distance 1200 mm.
EA
850
TM
57000
SM
304
SM
320
SM
306
SM
755
The ceiling sections should be fixed to intermediate channels with connecting clips (India
Gypsum code no. ME9). GI grid shall be fixed to RCC slab above with the help of 25x0.5 mm
strap hanger (India Gypsum code no. MF 8) and soffit cleat (India Gypsum code no. P534). The
joints between soffit cleat and strap hanger and GI grid & strap hanger shall be with 6.4x12.7
mm nut and bolt (India Gypsum code no. P526). Soffit cleat shall be fixed to RCC ceiling with
W.E. type 12 mm dia, 17/16" long steel rawl plug. Maximum c/c distance (both ways) of strap
hangers shall be 1200 m. The Gypboard shall be fixed fixed to GI grid with 25 mm long Drawall
screws. The Gypboard to be used shall be 12.5 mm thick tapered edge boards. The boards shall
be taped & filled from underside to ceiling.
The rate shall be inclusive of additional ceiling sections and intermediate channels shall be
provided at openings for light fixtures, AC ducts, vertical drops, offsets etc Additional
intermediate channels shall be fixed to strap hangers at every 1200 mm for additional support to
prevent strap hangers from buckling/swaying. Item to be completed in all respect including
necessary sleeves for ducts , finishing of joint cut outs, supports for AC grills, light fixtures,
speakers etc. complete as per directions of Engg.-In-Charge.
125
MINARAL FIBRE FALSE CEILLING ( ARMSTRONG)
Providing and fixing Mineral Fibre board false ceiling ( Armstrong Make) with required
accessories including fixing of the GI channels (18 guage), fixing of the sheets in pattern , in
proper line & level, filling the joint with sealent etc. complete as per the satisfaction of EIC.
SM
1041
126
ACOUSTIC. SUSP. CEILING BUTT..
SM
920
Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles
having butt edges . The tiles should have Humidity Resistance of 90% RH, Average NRC .50,
Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White, Fire
Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on
24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main
Runner, 1200 mm & 600 mm Cross Tees.
INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the
structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end
of each main runner should not be greater than 450mm from the adjacent wall.
Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre
to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent
support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees
centrally between the 1200 mm cross tees.
Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/c
For fissured RH 90 Butt Edge.
127
ACOUSTIC. SUSP. CEILING TEGULAR
Providing & Fixing of Armstrong Acoustical Suspended Ceiling System with Fissured Tiles
having Tegular edges . The tiles should have Humidity Resistance of 90% RH, Average NRC
.50, Light Reflectance >80%, Thermal Conductivity k = 0.052 – 0.057 w/m°c, Colour White, Fire
Performance Class 0/Class 1 (BS - 476) in module size of 600mm x 600mm x 15mm laid on
24XL - Hot Dipped Galvanised steel suspension System having rotary stitching on the Main
Runner, 1200 mm & 600 mm Cross Tees.
INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the
structural socket by approved hanger at 1200mm maximum centre. The last hanger at the end
of each main runner should not be greater than 450mm from the adjacent wall.
Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre
to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent
support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees
centrally between the 1200 mm cross tees.
Perimeter trim to be Armstrong wall angles or channel, secured to walls at 450 mm max. C/c
For fissured RH 90 Tegular Edge.
SM
1200
128
EUROPEAN TYPE W/C- WHITE
EUROPEAN TYPE Supplying and fixing white wall mounted vitreous china European type water
closet comprising of the following accessories including cutting and making good the walls &
floors wherever required complete as directed by Engg.-In-Charge, having following (A) White
vitreous china European water closet with P or S trap of Parryware make Cascade series No.
0219 having integral matching colour vitreous china cistern supplied as part of the closet with all
mechanisms, with necessary fittings, brackets, screws, etc all complete as per the direction of
Engg.-In-Charge.
EA
3320
EA
4325
EA
2830
(B) 15mm NB CP brass angle valve of approved brand as per the direction of Engg.-In-Charge
(C) 15 mm NB CP brss inlet connection with Brass unions at the ends. (D)
Parryware/Commander make or equivalent matching colour polypropylene seat cover with
necessary brass hinges and rubber bushes etc (E) WC connector with neoprene rubber etc.
Approved Equivalent - Hindware 20028 with matching colour Vitreous China cistern with all
mechanisms, fittings etc. complete.
129
130
EUROPEAN TYPE W/C- OFF WHITE
Same as above but OFF WHITE
INDIAN TYPE W/C- WHITE
INDIAN WATER CLOSET Supplying and fixing white coloured vitreous china Orissa Pan type
water closet comprising of the the following accessories including cutting and making good the
walls & floors wherever required complete as directed by Engineer In Charge. A)Coloured
(pastel colour) viterous china 580 mm orissa pan water closet of Hinduatn sanitaryware or any
equivalent make with P or S trap. B) 10 litres capacity hi-grade engineering plastic low level
flushing cistern of matching colour Parry Slimline make model 8068 or approved equivalent
make with necessary fittings , brackets , screws etc. all complete . C) 32 mm PVC flush pipe 10
Kg/Sqcm quality of approved lengt with necessary fittings ,clamps etc. D) 15 mm NB CP inlet
connections with brass union at the ends E) 15 mm NB brass angle valve as per ISI of
approved brand as per the direction of Engineer In Charge F) WC connector with neoprene
rubber\. Approved Equiv. - Hindware Cat. 20004 with equivalent low level cistern
131
132
133
134
135
136
137
138
INDIAN TYPE W/C- OFF WHITE
Same as above but OFF WHITE
URINALS
URINALS : Supplying and fixing colored ( pastel coloures) vitreous china flat back urinal of size
300 mm x 400 mm with integrated overflow of Hindustan Sanitory or equivalent approved make
with CP flush valve , CP pipe connection , CP waste coupling , CP Brass bottle trap of Jaquar
mak, 32 mm PVC waste line of required length etc all complete as per the direction of engineer
in charge.
LARGE URINALS - MAGNUM
Supplying and fixing coloured (pastel colours) viterous china flat back urinal of large size with
integrated overflow system of Hindware Sanitary make,MODEL NO: 60002 or approved
equivalent from Parryware-MAGNUM ,with Spreaders,CP flush valve, CP pipe connection, CP
waste coupling , CP Brass bottle trap of Jaquar make, 32 mm PVC waste line of required
length etc. all complete as per the direction of Engineer In Charge
EA
3715
EA
1920
EA
3665
URINALS WITH BUILT IN SENSORS
Supplying and fixing coloured (pastel colours) viterous china flat back urinal of large size with
integrated auto flush system of 0575 New Magnum Parryware Sanitary make with CP flush
valve of Jaqaur make, cp pipe connection, CP waste coupling , CP Brass bottle trap of Jaquar
make, 32 mm PVC waste line of required length etc. all complete as per the direction of
Engineer In Charge
URINAL DIVISIONAL PLATE
URINAL DIVISION PLATE Providing and fixing 1200 x 450 x 18 mm size granite partition plate
between urinals including cutting masonary/concrete surface to required size, fixing the division
plate on the ceramic tiles by means of SS clamps, nuts & bolts, polishing all exposed surface etc
all complete as directed by Engineer In Charge.
URINALS SENSORS
Supply, installation and commissioning all complete Jaquar make Sensotronic Concealed type
Flushing system (Model 51087 - Chrome) including all accessories, all connections, electricals
etc. all complete as per the direction of Engg.-In-Charge.
HAND WASH BASIN
HAND WASH BASIN Providing and fixing coloured (pastel colours) wash basins of size 550 x
400 without pedestal Including the following accessories: -15mm brass CP Jaquar make
(Cat.no.093) stop cock -1 No . -15mm CP connections from the above stop cock to pillar cock - 1
No. -32mm dia waste coupling, CP brass chain and rubber stopper. -30mm Dia. bottle trap
Jaquar make with cleaning eye, extension piece and wall flange. -Providing and fixing brass CP
Jaquar make 13mm half turn pillar cock.(Cat. no.011)Rate to include supply , painting and fixing
of necessary CI brackets with nuts and bolts and fixing the wash basin with all necessary
connections in walls .
EA
13375
EA
2345
EA
8650
EA
2350
COUNTERTOP WASHBASIN OVAL TYPE
Providing &fixing colored COUNTER TOP washbasin :OVAL below Counter Basin 550 0418 of
Parryware/10016 HINDWARE Or appoved equivalent including all the required accessories like:
-15mm brass CP Jaquar make (Cat.no.093) stop cock -1 No . -15mm CP connections from the
above stop cock to pillar cock - 1 No. -32mm dia waste coupling, CP brass chain and rubber
stopper. -30mm bottle trap Jaquar make with cleaning eye, extension piece and wall flange. Providing and fixing brass CP Jaquar make 13mm half turn pillar cock.(Cat. no.011)
EA
5450
139
EWC EUR.WALLMOUNT (CAS. OFF WT.)
Providing &fixing WC Europeun WALL MOUNTED WC CASCADE 0219 PARRYWARE OR
20028 -HINDWARE (offwhite) with P or approved equivalent of Hindware with P or S trap
INCLUDING ALL THE ASSOCAITED ACCESSORIES AND FITTINGS like WC cover of
approved make ,15mm NB brass angle valve as per BIS of approved brand ,15 mm NB CP inlet
connection with brass unions at the ends,WC connector with neoprene rubber with necessary
fittings ,brackets, screws etc. all complet as per the satisfaction of Engineer-in-charge.
EA
12000
140
SENSOR TAPS FAUCET
Providing and fixing in position CP sensor Faucet of 51071 Jaquar make as per the drawing.
The item includes all necessary fittings, accessessories etc. complete as per the direction of
Engineer In Charge .
CP TOWEL RING CLARION JAQUAR
Providing and fixing in position CP TOWEL RING CP mounted on wall of make 1121
CONTINENTEL JAQUAR
AUTOMATIC HAND DRYER
Providing, fixing and commissioning fully automatic hand dryer i.e. autostart on positioning the
hand and autostop. Care shall be taken so that tiling is not damaged while installation. Rate
includes PVC insulated power chord having copper conductor and Anchor ROMA make 3 pin
power plug matching ampere load of instrument. Make - Technocrats (Model Alpha AP-800) or
Euronics (Model CYC 30)
AUTO FRESHENER
Providing, fixing and commissioning fully automatic aerosol dispenser (Auto Freshener). The
price includes spray fragrance cam with approved aroma etc. complete. Rate includes PVC
insulated power chord having copper conductor and Anchor ROMA make 3 pin power plug
matching ampere load of instrument. Care shall be taken so that tiling is not damaged while
installation. Make - Technocrats (Model Deluxe)
AUTOMATIC SHOE POLISH MACHINE
Providing, fixing and commissioning fully automatic shoe polish machine with electronic eye
(infra red sensor) having both separate black and brown rollers. The machine shall start
automatically when shoe is placed and automatically stop. Rate includes PVC insulated power
chord having copper conductor and Anchor ROMA make 3 pin power plug matching ampere
load of instrument. Care shall be taken so that finishing is not damaged while installation. Make Technocrats (Model Executive Deluxe)
STOPCOCK CONCEALED-PARKO 1516
Providing and fixing in position CP brass stop cock Parko make classic line series No. 1516
including all necessary fixtures etc. complete.
SWAN NECK TAP-PARKO 1536
Providing and fixing in position CP brass swan neck tap Parko make classic line series No. 1536
on wash basins including all necessary fixtures etc. complete.
PILLAR COCK-PARKO 1501
Providing and fixing in position CP pillar cock of Parko make classic line series No. 1501
including all necessary fixtures etc. complete.
BIB COCK LONG BODY-PARKO 1511
Providing and fixing in position CP long body bib cock of Parko make classic line series No.
1511 including all necessary fixtures etc. complete.
BIB COCK LONG NOSE-PARKO 1506A
Providing and fixing in position CP long nose bib cock of Parko make classic line series No.
1506 A including all necessary fixtures etc. complete.
BIB COCK -PARKO 1506
Providing and fixing in position CP bib cock of Parko make classic line series No. 1506 including
all necessary fixtures etc. complete.
PILLAR COCK-JAQUAR 23011
Providing and fixing in position CP brass pillar cock with Aerator of Jaquar Clarion Range No.
23011. Rate to include all related civil repairs, fitments, joineries etc. complete.
PILLAR COCK-JAQUAR 23021
Providing and fixing in position CP brass long neck pillar cock with Aerator of Jaquar Clarion
Range No. 23021. Rate to include all related civil repairs, fitments, joineries etc. complete.
EA
11520
EA
755
EA
7980
EA
2850
EA
17100
EA
535
EA
808
EA
525
EA
539
EA
622
EA
423
EA
552
EA
690
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
BIB COCK-JAQUAR 23037
Providing and fixing in position CP brass bib cock of Jaquar Clarion Range No. 23037. Rate to
include all related civil repairs, fitments, joineries etc. complete.
BIB COCK-JAQUAR 23039
Providing and fixing in position CP brass bib cock with long thread of Jaquar Clarion Range No.
23039. Rate to include all related civil repairs, fitments, joineries etc. complete.
BIBCOCK LONG BODY-JAQUAR 23107
Providing and fixing in position CP brass long body bib cock with wall flange of Jaquar Clarion
Range No. 23107. Rate to include all related civil repairs, fitments, joineries etc. complete.
EA
530
EA
550
EA
735
BIB COCK-2 WAY-JAQUAR 23041
Providing and fixing in position CP brass bib cock of Jaquar make Clarion Range No.23041.
Approved equivalent Parko make.
ANGULAR STOP COCK-JAQUAR 23053
Providing and fixing in position CP brass angular stop cock (regulating valve) of Jaquar Clarion
Range No. 23053. Rate to include all related civil repairs, fitments, joineries etc. complete.
EA
795
EA
524
ANGULAR STOP COCK-JAQUAR 23055
Providing and fixing in position CP brass long thread angular stop cock (regulating valve) of
Jaquar Clarion Range No. 23055. Rate to include all related civil repairs, fitments, joineries etc.
complete.
CONCEAL. STOPCOCK-JAQUAR 23069
Providing and fixing in position CP brass concealed stop cock (reduced body) of Jaquar Clarion
Range No. 23069. Rate to include all related civil repairs, fitments, joineries etc. complete.
EA
552
EA
705
CONCEAL. STOPCOCK-JAQUAR 23083
Providing and fixing in position CP brass Extra Heavy Body concealed stop cock with adjustable
wall flange of Jaquar Clarion Range No. 23083. Rate to include all related civil repairs, fitments,
joineries etc. complete.
SS GRAB BAR DESIGN A/B
SS GRAB BAR (A) and (B):Fabricating and fixing S. S. Railing with 40 mm dia MS Piperail &
using 10X10 MS bar welded to Balaster ( diagonal pieces) and 20 x 20 MS Baluster as per the
drawing. (GRAB BAR A &B).The item includes fabrication, buffing of the railing upto req. finish,
fixing the railing at position with m20 grade concrete, finising the SURFACE properly etc.
complete
SS STAIRCASE RAILING
SS STAIRCASE RAILING ::Fabricating and fixing S. S. Railing with 40 mm dia MS Piperail &
using 10X10 MS bar welded to Balaster ( diagonal pieces) and 20 x 20 MS Baluster as per the
drawing. (STAIRCASE DETAIL -HPCL-A-J100-DD-65.The item includes fabrication, buffing of
the railing upto req. finish, fixing the railing at position with m20 grade concrete, finising the
SURFACE properly etc. complete
MIRROR 600X600X5.5
MIRROR Providing and fixing bevelled edge mirror of superior glass of 5.5 mm thick & 600 x 600
mm size of BELGIUM GLASS or any other equivalent make, 3mm thick felt backing or 6 mm
asbestos sheet or with wooden beads allround of specified size and fixed with wooden plugs
with CP brass screws and cup washers etc all complete as directed by Engineer In Charge
EA
840
EA
6000
MR
2300
EA
675
164
MIRROR 5.5 MM THK
Providing and fixing beveled edge mirror of superior glass of 5.5 mm thick of BELGIUM GLASS
or any other equivalent make, craft paper, 3mm thick felt backing or 6 mm asbestos sheet. Teak
Wood beads 25x40 mm as per approved shape/drawing allround and fixed with wooden plugs
with CP brass screws and cup washers etc all complete as directed by Engg.-In-Charge.
SM
1865
165
SOAP TRAY
SOAP TRAY Providing and fixing readymade CP brass soap tray near wash basin with CP brass
screws of approved make.
LIQUID SOAP DISPENSERS
LIQUID SOAP DISPENSERS Providing and fixing readymade CP brass liquid soap dispenser
near wash basin with CP brass screws of approved make.
EA
245
EA
572
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
TOILET PAPER HOLDER
TOILET PAPER HOLDER Supplying and fixing of 150 x 150 mm pastel coloured toilet paper
holder of Hindustan Sanitary ware or equivalen approved make at required position and
elevation as directed. Rate to include making good the chases in walls after fixing the above.
TOWEL RAIL
TOWEL RAIL Providing and fixing CP brass towel rail of 20 mm dia and 600 mm long including
all accessories such as brackets (coloured), fixed and anchoring etc. complete as directed.
EA
403
EA
515
15MM DIA STOP COCKS
Providing and fixing in position CP brass stop cock of heavy type ISI marked of approved make.
Size 15mm diameter
15MM DIA BIB COCKS
Providing and fixing in position CP brass bib cock of heavy type ISI marked of approved make.
Size 15mm diameter
15MM DIA PILLAR COCKS
Providing and fixing in position CP brass pillar cock of heavy type ISI marked of approved make.
Size 15mm diameter
15MM DIA HALF TURN COCKS
Providing and fixing in position CP brass half turn cock of heavy type ISI marked of approved
make. Size 15mm diameter
HYGI SPRAY
Providing and fixing in position CP brass Hygi Spray of Parryware make Model T9929G1
inclusive of all fixtures, fittings and fasteners making operational complete. Approved Equivalent
Make - Hindware
15mm DIA CONCEALED GI PIPE
Providing & fixing followg. size medium duty GI pipes of TATA/ JINDAL/ZENITH/GST make
conforming to IS-1239 concealed in the walls/under the concrete floors including making chases
in the walls/concrete floors,fixing with clamps at every 1m c-c, necessary
tees,bends,elbows,plugs,nipples,unions,testing of pipelines for leaks upto a pressure of 6 Kg/sq
cm , painting the pipes with hot bitumen, wrapping the pipes with hessian cloth and making
chases of the walls good after piping complete.
EA
484
EA
555
EA
725
EA
865
EA
595
MT
168
MT
189
MT
154
MT
174
MT
236
MT
275
MT
325
MR
165
MR
221
MR
247
MR
275
MR
325
20MM DIA CONCEALED GI PIPE
Same as above but size 20 mm dia
15MM DIA EXPOSED GI PIPE
Same as above but laying in open on brick or RCC surface with the help of MS 'U' clamps at
every 1 m and at every turn.
20MM DIA EXPOSED GI PIPE
Same as above but size 20mm dia
25MM DIA EXPOSED GI PIPE
Same as above but size 25mm dia
32 MM DIA EXPOSED GI PIPE
Same as above but size 32mm dia
40 MM DIA EXPOSED GI PIPE
Same as above but size 40mm dia
UPVC PIPE 40 MM DIA 4KG/SQCM
Providing and laying unplasticised polyvinyl chloride (UPVC) pipes of class IV or as applicable
conforming to IS 4985:2000/ IS 15328 : 2003/ IS 13592 : 1992 Type B/ BS 4514/ BS EN 1329,
latest edition including all necessary fittings conforming to IS 14735 : 1999/ BS 4514/ BS EN
1329, latest edition and other accessories including connections etc., complete as per drawings
or as directed at site. Size 40 mm diameter.
UPVC PIPE 63 MM DIA 4KG/SQCM
Same as above but size 63 mm dia
UPVC PIPE 90 MM DIA 4KG/SQCM
Same as above but size 90 mm dia
UPVC PIPE 110 MM DIA 4KG/SQCM
Same as above but size 110 mm dia
UPVC PIPE 160 MM DIA 4KG/SQCM
Same as above but size 160 mm dia
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
40MM DIA GATE VALVE
Providing & fixing brass full way gate valve ISI marked & of Leader/GG make or approved
equivalent as directed by Enginner In Charge. Size 40 mm diameter
32MMDIA GATE VALVE
Same as above but size 32mm dia
25MM DIA GATE VALVE
Same as above but size 25mm dia
15MM DIA GATE VALVE
Same as above but size 15mm dia
WATER TANK-1000 LTRS
WATER TANK Supplying and installation of HDPE water tanks Sintex / Fusion / Polycon make
of 1000 litre capacity including 300 mm high brick masonry pedestal of 230mm thick in CM 1:5,
providing 75mm thick RCC 1:2:4 slab with reinforcement 8mm tor @150mm c/c, lifting the tank ,
making all necessary GI connections to inlet, outlet, and overflow nozzles and cleaning the tank
before commissioning.
WATER TANK-5000 LTRS
WATER TANK Supplying and installation of HDPE water tanks Sintex / Fusion / Polycon make
of 5000 litre capacity including 300 mm high brick masonry pedestal of 230mm thick in CM 1:5,
providing 75mm thick RCC 1:2:4 slab with reinforcement 8mm tor @150mm c/c, lifting the tank ,
making all necessary GI connections to inlet, outlet, and overflow nozzles and cleaning the tank
before commissioning.
110MM DIA PVC PIPE
PVC SOIL / WASTE /RAIN WATER PIPE: Supplying and laying the PVC pipe of 6KG/sqcm
pressure rating including plain or door type bends, shoes, offsets, clamps junctions, tees, etc,
complete. Also including cutting, bending & supply and laying of 17 SWG annealed binding wire
inside the Pipe for pulling cables in future. Size 110 mm diameter
80MM DIA PVC PIPE
Same as above but size 80mm diameter
NAHANI TRAP
NAHANI (FLOOR) TRAP Providing and fixing PVC floor trap of self cleansing design conforming
to IS specs with 100mm inlet, 75mm outlet and 150mm CP hinged grating of 6mm thick with rim.
Rate shall include making all necessary leak proof connections etc .
STONE WARE PIPES ( 150 MM DIA)
STONE WARE PIPES Providing and laying 150mm dia. salt glazed stoneware pipes conforming
to IS 651 Grade-A including bends, tees etc, excavation of trenches, 100 mm thick PCC 1:4:8
bedding, providing PCC 1:2:4 haunches @ 0.5mc/c , filing the joints with tarred gasket,
plastering with 1:3 cement mortar smoke testing of joints,backfilling the trenches with excavated
earth, watering, ramming etc., complete.
CI PIPES Providing and laying ISI marked centrifugally cast (spun) Iron pipes conforming to IS
3989 :1984 latest edition incuding all bends, joints, Ts, cowls etc. with painted MS clampings of
appropriate strength @ 1 m c/c. The pipe will be painted with two coats of red oxide and smoke
tested after making joints and before joining to the system. The joints will be socket spigot
caulked joints with juite and molten lead/Drip Seal as per relevant BIS specifications and
procedures. Make - NECO/ HEPCO/ ACL or approved Equivalent
100MM DIA CI PIPE
CI PIPES 100MM DIA Providing and laying CI pipes of 100mm dia of standard quality and make
including fittings, bends, tees, etc.,complete.
75MM DIA CI PIPE
CI PIPES 75MM DIA Providing and laying CI pipes of 75mm dia of standard quality and make
including fittings, bends, tees, etc., complete.
GULLY TRAP WITH CHAMBER
GULLY TRAP WITH CHAMBER Providing and fixing square mouth gully trap including
constructing 300 X 300 MM internal size brick masonary chamber with 230mm thick brick
masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with neat
cement finish, Medium duty CI cover with frame etc. complete.
25MM DIA NON RETURN VALVE:
Providing and fixing brass Non-Return Valve GG/LEADER make ISI marked or approved
equivalant
15MM DIA NON RETURN VALVE
EA
1345
EA
1159
EA
765
EA
482
EA
7200
EA
26980
MT
292
MT
225
EA
653
MT
250
MT
765
MT
615
EA
1700
EA
1051
EA
905
210
202
203
204
205
206
207
208
209
210
211
212
Same as above but size 15mm diameter
FLOAT VALVE
FLOAT VALVE Providing and fixing Float Valve (Ball cock) of polypropylene or synthetic metal
(Symet) float and rod of approved make of 25mm dia. nominal bore.
600X600X600MM INSPN. CHAMBERS
Providing and constructing inspection chambers of size 600X600X600 mm\ with 230mm thick
brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed, plastering with
neat cement finish etc. complete. ( Chamber cover & angle Frames will be paid separately)
450X450X600MM INSPN. CHAMBERS
Same as above but size 450X450X600 mm
600X450X600 MM INSPN. CHAMBERS
Same as above but size 6000X450X600 mm
SEWER TRAP CHAMBER
SEWER TRAP CHAMBER Providing and constructing sewer trap with conical frame work in 9"
thick BM chamber with CM1:4 conical chamber of size 3.5"dia at top and 4.5" dia at bottom and
depth as per required slope including cement plater inside and outsite with CM1:4 including
necessary foundation and excavation. The job includes providing CI cover of weight not less
than 100KGs, etc., complete. The job is to be carried out as per local municipal rules and
regulations by licensed plumber.
SEPTIC TANK (25 PERSON)
SEPTIC TANK Prpoviding & constructing septic tank of size 1200x2000x1800mm depth with
excavation ,PCC1:4:8 100mm thick bed , 345/230mm thick brick masonary wall in CM 1:5
,RCC1:2:4 100mm thick slab with 8mm tor steel @150c/c both way , 115mm thick baffle wall with
RCC beam at bottom ,12mm thick smooth cement plaster with water proofing compound inside
and exposed outside portion, providing 600mmx600mm size medium duty CI cover, providing
75mm dia PVC vent pipe etc. Complete.
SOAK PIT 2.5 M DIA X 3.0 M. DEPTH
SOAK PIT Providing and constructing soak pit of 2.5m dia X 3m depth (internal) in brick masonry
of class 75 design. Internal size of shaft shall be minimum clear 1m with minimum 230thk. walls
in cement mortar 1:6 at top 500mm in height and in bottom 230mm wall in height with
450mmx450mm dry brick honey comb shaft and surrounded by broken brick bats. The outer
walls of the shaft should be 230 mm followed by 150 mm thick layer of 50-80 mm nominal size
brick aggregates thereafter followed by 150 mm thick layer.
CI COVER 450X450MM - 16 KG
CI covers for Chambers / Inspection chambers etc : Supply and fixing of CI cover and frame of
450X450 mm nominal size(total weight not less than 16 kg) with seal, all materials and labour
complete.
CI COVER 600X600MM - 34 KG
Same as above Item but of size 600x600 mm and total weight not less than 34 kg.
PT.WIRING MOD. PLT SWITCH LT/FAN
POINT WIRING FOR LIGHT/FAN WITH MODULAR PLATE SWITCHES ANCHOR/MK
Providing and laying point wiring in concealed conduits for the following points using specified
1100V grade PVC insulated,FRLS multistranded 3 x 1.5 sqmm copper conductor wires. Rate to
include supplying, laying and securing in position in roof slabs and brick walls or concrete
columns 25 mm dia rigid PVC conduits of approved make with necessary accessories and
junction boxes/pull boxes. Providing and fixing in the brick wall flush type metal switch boxes of
approved make shade and sufficient size to accomodate all 6A Modular switches/3 pin
socket,screws,holders .ceiling roses and fan regulator wherever required. Rate to include wall
chasing and rough plastering . Providing and fixing single pole 5A modular plate switches of MK
or ANCHOR make of approved colour.One switch shall be provided for each light and fan point.
Rate to also include providing main circuit wiring from DB to switch boards with 2.5 sqmm
copper wire .
5A SOCKET SWITCH
Same as above but for 5A socket controlled by one 5A switch on the same lighting board
5A SOCKET SWITCH INDEPENENTLY
Same as above but for 5A socket controlled by one 5A switch independently mounted including
providing wiring with 3 runs of 1.5 sqmm pvc insulated copper wire through PVC conduit
EA
463
EA
2350
EA
2100
EA
2200
EA
3955
EA
23400
EA
11750
EA
660
EA
1550
EA
650
EA
450
EA
550
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
5/15A SOCKET SWITCH
Same as above but for 5/15A socket controlled by 15A switch independently mounted including
providing wiring with 2 runs of 2.5 sqmm and 1 run of 1.5 sqmm PVC insulated copper wire
through PVC conduit
AC POINT
Same as above but for for AC point with 2 runs of 4 sqmm (P&N)and 1 run of 2.5 sqmm
(earthing) PVC insulated , FRLS multistrand copper cable in 25 mm dia PVC conduict from
MCBDB to 20 A powersocket. The conduit shall be partly/fully concealed in all types of wall,
ceiling etc complete with all accessories, wiring, termination, connected civil works, rough
plastering etc including supply and fixing of 20A industrial socket controlled by 20A SPMCB of
MDS/HAVELS make.
4X10+1X6 SQMM MULTIST.FRLS CU
Supply, laying, and commissioning of wiring using 4 runs of 10 sqmm and 1 run of 6 sqmm
PVC insulated , FRLS, unsheathed, multistranded copper wires conforming to IS 694:1990 in
40 mm dia medium duty PVC conduit (Conforming to IS 9537:Part 3:1983) from panel to
Distribution boards. Rate to include supply of 16 GI fish wire, conduits & accessories, wiring,
terminations etc complete.
4X6+1X4 SQMM MULTIST. FRLS CU
Same as above item but supply, laying, and commissioning of wiring using 4 runs of 6 sqmm
and 1 run of 4 sqmm FRLS multistranded copper wire in 32 mm dia PVC conduit from panel to
Distribution boards.
4X6+2X4 SQMM MULTIST. FRLS CU
Same as above item but supply, laying, and commissioning of wiring using 4x6 sqmm and 2x4
sqmm FRLS multistranded copper wire in 40mm PVC conduit
3X10 SQMM MULTIST. FRLS CU
Same as as above item but supply, laying, and commissioning of wiring 3x10 sqmm FRLS
multistranded copper wire in 40mm PVC conduit
3X6 SQMM MULTIST. FRLS CU
Same as above item but supply, laying, and commissioning of wiring 3x6 sqmm FRLS
multistranded copper wire in 40mm PVC conduit
FRLS MULTISTR. 1.5 SQMM COPPER
Supply and laying through conduit FRLS multistranded PVC insulated (1100V) copper wire
conforming to IS 694:1990 and of size 1.5 sqmm including termination etc. all complete. PVC
Conduits to be paid for separately as per relevant items.
FRLS MULTISTR. 2.5 SQMM COPPER
Same as above item but size 2.5 sqmm
FRLS MULTISTR. 4.0 SQMM COPPER
Same as above item but size 4.0 sqmm
FRLS MULTISTR. 6.0 SQMM COPPER
Same as above item but size 6.0 sqmm
18 SWG PVC INSUL. COPPER WIRE
Same as above item but for single core PVC insulated copper wire 18 SWG.
PVC CONDUIT MED. IS:9537-25MM
Supply and laying rigid non-flame propagating medium duty PVC conduit 25 mm dia. conforming
IS 9537(Part III) including all bends, clamps, joineries, fixing on the wall etc. all complete
PVC CONDUIT MED. IS:9537-32MM
Same as above item but 32 mm dia
PVC CONDUIT MED. IS:9537-40MM
Same as above item but 40 mm dia
CEILING FANS 1400 MM SWEEP
CEILING FANS Supplying and fixing of the ceiling fans of Crompton/GE/Polar with detail as
below : Sweep
:1400 mm, Colour
:White, Bearing type :Double ball bearing, Down Rod
: Clear 300 mm long, Regulator : Electronic type ANCHOR/MK make, Accessories : Screws,
wall nuts etc.
Supply, fixing and commissioning of Exhaust fans of following dia including bird louvers, frame
works and other civil works like chipping and making the surface good etc
EXHAUST FANS 305MM DIA
EXHAUST FANS 230MM DIA
EA
585
EA
1910
MR
315
MR
225
MR
252
MR
216
MR
154
MR
14
MR
22
MR
34
MR
60
MR
10
MR
16
MR
25
MR
34
EA
2065
EA
EA
1720
1540
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
1x36W TUBE LIGHT FITTING
Supply, fixing and commissioning of box type light fitting Philips make cat no. TMC501/136 HPF
(High Power Factor) 1 x 36 W tube light fitting with lamp or equivalent of Crompton make Cat.
DJB 14. Rate to include all accessories, interconnection of wires from ceiling rose to the fittings
and fluorescent tube lamps , copper ballast etc.
1x60W SPOT LIGHT FITTING
1 x 60W spot light luminaire with 1 meter track including lamp Philips make cat no. DGN 451 or
equivalent for display shelving
1x60W BULK HEAD FITTING
1 x 60 W Bulk head luminaire including lamp Phillps cat no. NXC 101 or equivalent Crompton
make:CBHE 29 ( Outside building).
ANGLE HOLDER WITH 60W LAMP
Providing & fixing in position Angle holder Anchor make including lamp 60W (Toilets).
1x36W TUBE LT. FIT. TMS 21/136
1 x 36 W tube light fitting including lamp Phillps cat no TMS 21/136 HPF or equivalent ( stores,
service area)
2x36W TUBE LIGHT FITTING
2 x 36 W tube light fitting including lamp Phillps cat no TBS 50/236 HPF or equivalent (for false
ceiling area)
2x36W INDOOR DECORATIVE LIGHT
2 x 36 W INDOOR DECORATIVE 'Flatlite' luminarie including holding down rod, lamp, etc.,
complete of Philips make Cat. No. TCx20/236 HPF or equivalent.
MIRROR OPTIC FTG.-TCS605/236M1
Same as above item but 2 x 36 W indoor decorative surface mounted tube light fitting including
lamp Philips cat no TCS 605/236 M1 HPF (High Power Factor) or equivalent of Crompton make
Cat. CBSW 1124 HSB.
MIRROR OPTIC FTG.-TBS300/418M1
Same as above item but 4 x 18 W indoor decorative mirror optics luminaire suitable for
recessed mounting including 4 nos. TL D lamps Philips cat no TBS 300/418 M1 HPF (High
Power Factor) or equivalent of Crompton make Cat. CRFN 42 HSB.
CORNER LUMINAIRE-ACW/N- 1X18W
Same as above item but Corner/wall slim (corner luminaire with lamp, reflector clear receded
acrylic cover Arcade make). 1X18W
CORNER LUMINAIRE-ACW/N- 1X36W
Same as above item but Corner/wall slim (corner luminaire with lamp, reflector clear receded
acrylic cover Arcade make). 1X36W
DECORATIVE LUMINAIRE-AMA-1X18W
Same as above item but Decorative luminaire with lamp reflector, opal/clear receded acrylic
cover Arcade make. 1X18W
DECORATIVE LUMINAIRE-AMA-1X36W
Same as above item but Decorative luminaire with lamp reflector, opal/clear receded acrylic
cover Arcade make. 1X36W
ENERGY ESSENTIALS- 11 W
Same as above item but supply and fixing energy essential CFLs 11 W of PHILIPS make.
Approved equivalent - Havell/ Osram
ENERGY ESSENTIALS- 14 W
Same as above item but supply and fixing energy essential CFLs 14 W of PHILIPS make.
Approved equivalent - Havell/ Osram
ENERGY ESSENTIALS- 18 W
Same as above item but supply and fixing energy essential CFLs 18 W of PHILIPS make.
Approved equivalent - Havell/ Osram
SURFACE MOUNTED LUMINARE TCS 30
Providing and fixing light fixtures Surface Mounted Lumonaire Philips TCS 306 or approved
equivalent from GE/BAJAJ/CROMPTON including lamp and other allied accessories.
SURFACE MOUNTED LUMINARE CFL FC
Providing and fixing light fixtures Surface Mounted Lumonaire Philips CFL FCS 518 LOTUS or
approved equivalent from GE/BAJAJ/CROMPTON including lamp and other allied accessories.
EA
1800
EA
1185
EA
620
EA
62
EA
820
EA
2795
EA
1995
EA
1900
EA
2650
EA
950
EA
1040
EA
939
EA
875
EA
145
EA
160
EA
189
EA
1990
EA
1850
FBS 300
EA
600
P5 RECESS MOUNTED
providing and fixing light fixtures Recess Mounted Lumonaire Philips FBS 300 P5 or approved
equivalent from GE/BAJAJ/CROMPTON including lamp and other allied accessories.
TEL. SOCKET POINT 2 PAIR
TELEPHONE SOCKET POINT Supply and laying 2 pairs of 0.5 mm dia screened and shilded
telephone wire in 20 mm dia PVC conduit partly/fully concealed in types of walls , floor etc
complete with all accessories , wiring terminations, connected civil works, rough plastering etc
including supply of 16 GI fish wire conduit & accessories etc.
TEL. TAG BLOCK 5 PAIRS
Supply, fixing and commissioning of ffive pairs of telephone tag block of Krone type enclosed in
suitable MS box. Rate shall include all accessories, connected civil works for fixing the same as
per specifications.
TEL. SOCKET
Supply and installation of modular type telephone socket MK make in a suitable size box
concealed to wall including all civil works
METER BRD (PART-C EX. ELECT.)
Supply and fixing of wall mounting type meter board made out of 16 SWG CRCA sheet steel
and single iron with 3 nos 200A Fuse cutouts N.L ,1 no. earth link , 1 no neutral link and space
for accommodating 1 no. 3 ph, 4 wire KWH meter complete with adequate size of copper wire
interconnections, powder coating etc. complete.
PNL BRD-300ATPN 2X125/3X63/6X32A
Supply and erection, testing commissioning of floor mounting type cubical panel board made out
of 16 SWG CRCA sheet steel with 300 A TPN copper bus bars, interconnections, earthing,
powder coating and comprising of the followings as required. Incomer : 2 nos 125A TP switch
fuse unit with HRC fuses for DG and EB with interlocking 1 no.125A TP bus coupler/2 nos.volt
meter with volt meter selector switch/2 no ammeter with CT & Ammeter selector switch/2 sets of
Phase indicating lamp (RYB)//Outgoings : 3 nos 63A and 6 nos 32A TP fuse switch unit with
HRC fuse/5KVAR capacitor : 2 nos.
MT
45
EA
720
EA
450
EA
6150
EA
78000
255
FLR.MNT.PANELBOARD-2X125 2X63A
Supply and erection, testing commissioning of floor mounting type cubical panel board made out
of 16 SWG CRCA sheet steel with 200 A TPN copper bus bars, interconnections, earthing,
powder coating and comprising of the followings as required. Incomer : 2 nos 125A TP switch
fuse unit with HRC fuses for DG and EB 1 no 125A 4 pole change over switch 2 no volt meter
with volt meter selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of
Phase indicating lamp (RYB) Outgoing : 2 nos 63A and 3 nos 32A TP fuse switch unit with
HRC fuse/5 KVAR capacitor: 1 no.
EA
69386
256
FLR.MNT.PANELBOARD-2X63/4X32A
Same as above item but with following details Incomer : 2 nos 63A TP switch fuse unit with HRC
fuses for DG and EB 1 no 63A 4 pole change over switch 2 no volt meter with volt meter
selector switch, 2 no ammeter with C T & ammeter selector switch, 2 sets of Phase indicating
lamp (RYB) Outgoing : 4 nos 32A TP fuse switch unit with HRC fuse with HRC fuse 5 KVAR
capacitor : 1 no .
PNL BRD-Inc.2X63,Outgo1X63/3X32A
Same as above but with following details:- Incomer :2 nos 63A TP switch fuse unit with HRC
fuses for DG and EB/1no. 63A 4 pole change over switch (on line)/2 no volt meter with volt meter
selector switch/2 no ammeter with CT & ammeter selector switch/2 sets of Phase indicating
lamp (RYB)//Outgoings : 1 no 63A and 3 nos 32A TP fuse switch unit with HRC fuse 5 KVAR
capacitor : 1 no
HENSEL -LT PANEL 25 KVA
Design, fabrication, supply, installation, testing and commissioning of factory made LT switch
board/ panel of Make - HENSEL made out of polycarbonate, polyestrene thermoplastic
modules/enclosure with IP 65 degree of protection. Please refer to attched specifications, list of
items, bill of materials and drawing nos. HENMIPDB31705 for details. Approved Equivalent Fybox, Rittal
EA
55000
EA
39500
EA
96936
250
251
252
253
254
257
258
Bus Bar Rating: 250 A (12x10, 12x5 mm Cu), System Voltage: 415 V, 50 Hz
Incomer: 125A FP COS - 1No.; 100A TPN SFU - 1No.; 70A Contactor - 1No.
Outgoings: 32A FP ISOLATOR - 1 No.; 32A FP MCB - 2 Nos.; 20A DP MCB - 2 Nos.; 32A DP
MCB - 14 Nos.; 10A DP MCB - 17 Nos.; 40A FP ISO - 1 No.
Metering: Voltmeter with selector switch (0-500V) - 1 No.; Ammeter with selector switch (0-63A) 1 No.; Frequency Meter - 1 No.; Current Transformer(63/5A) - 3 Nos.; R/Y/B LED Indication each 1 No.; On/Off PB - each - 1 no.; Control Fuse with Base - 6 Nos.
Terminals: 50 Sqmm Feed in Terminals - 10 Nos.; 6 Sqmm - 85 Nos.; 4 Sqmm Earth Terminals 35 Nos. Rate to include approved front cable cover, pedestal frame with FRP lining and canopy
as per manufacturer's specifications.
Note: For any outlet having requirement of more than 25 KVA load, the panel has to be
separately designed using the above basic material of approved manufacturers. The payment
shall be made separately basis the original quotation received from manufacturer and approved
by HPCL Engg.-in-Charge.
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
63A TPN MCB DB
Supply, installation and commissioning of 63A TPN MCB DB Incomer : 1 no 63 A , 4 Pole MCB
Outgoings : 18 nos, 10A/16A/20A SP MCBs
32A TPN MCB DB
Supply, installation and commissioning of 32A TPN MCB DB Incomer : 1 no 32 A , 4 Pole MCB
Outgoings : 12 nos, 10A/16A/20A SP MCBs
Supply and laying following size PVC insulated, sheathed, armoured cable of approved make
EA
6320
EA
4230
3.5CX 120 SQMM AL CABLE
Supply and laying 3.5 core X 120 sq mm size PVC insulated, sheathed, armoured aluminium
cable of approved make
3.5 C X 95 SQMM AL CABLE
Same as above but size 3.5 core X 95 sqmm
3.5CX 70 SQMM AL CABLE
Same as above but size 3.5 core X 70 sqmm
3.5CX35SQMM AL CABLE
Same as above but size 3.5 core X 35 sqmm
4CX16SQMM AL CABLE
Same as above but size 4 core X 16 sqmm
4CX6SQMM AL CABLE
Same as above but size 4 core X 6 sqmm
4CX2.5SQMM COPPER CABLE
Supply and laying 4 core X 2.5 sq mm size PVC insulated, sheathed, armoured copper cable of
approved make
3CX2.5SQMM COPPER CABLE
Same as above but size 3 core X 2.5 sq mm
2CX2.5SQMM COPPER CABLE
Same as above but size 2 core X 2.5 sq mm
4CX1.5SQMM COPPER CABLE
Same as above but size 4 core X 1.5 sq mm
END TERMINATION End termination of following cable with double compression NFLP gland
and crimping sockets
3.5CX120SQMM AL CABLE END TER
End termination of cable. Approved make Broco/Dowells/Commet/Cosmos
3.5CX95 SQMM AL CABLE END TER
Same as above but for size 3.5 core X 95 sqmm
3.5CX70 SQMM AL CABLE END TER
Same as above but for size 3.5 core X 70 sqmm
3.5CX35SQMM END TERMINATION
Same as above but for size 3.5 core X 35 sqmm
4CX16SQMM END TERMINATION
Same as above but for size 4 core X 16 sqmm
4CX6SQMM END TERMINATION
Same as above but for size 4 core X 6 sqmm
4CX2.5SQMM END TERMINATION
Same as above but for size 4 core X 2.5 sqmm
3CX2.5SQMM END TERMINATION
Same as above but for size 3 core X 2.5 sqmm
MR
705
MR
560
MR
410
MR
300
MR
230
MR
130
MR
145
MR
132
MT
110
MT
130
EA
140
EA
120
EA
110
EA
75
EA
65
EA
58
EA
55
EA
46
279
280
281
282
283
284
285
286
287
288
2CX2.5SQMM END TERMINATION
Same as above but for size 2 core X 2.5 sqmm
4CX1.5SQMM END TERMINATION
Same as above but for size 4 core X 1.5 sqmm
3CX2.5SQMM END TER. DOB. COMP.
End termination of cable for size 3 Core X 2.5 sq mm with double compression NFLP gland and
crimping sockets. Approved make Broco/Dowells/Commet/Cosmos
2CX2.5SQMM END TER. DOB. COMP.
End termination of cable for size 2 Core X 2.5 sq mm with double compression NFLP gland and
crimping sockets. Approved make Broco/Dowells/Commet/Cosmos
4CX1.5SQMM END TER. DOB. COMP.
End termination of cable for size 4 Core X 1.5 sq mm with double compression NFLP gland and
crimping sockets. Approved make Broco/Dowells/Commet/Cosmos
CABLE TRENCH EXCAVATION
Excavation in any type of soil including WBM/asphalt up to 600mm depth and 300mm wide
including supply and laying 150mm thick sand on top and bottom of cable, supply and laying
bricks laid flat on top, back filling trench etc. complete.
JUNCTION BOX
Supplying and fixing flame proof and weather proof junction box of Sudhir / Baliga make out
door junction box of IP 54 category of protection with rubber gasket and having locking
arrangement including all required connectors, 10A SPMCB.
SINGLE ARM MS POLES
MS POLES Supply, Fabrication Erection of 7 mtrs high MS Pole having a base plate of size
300x300x16 with 1000 mm long 40mm MS pipe suitable for mounting 1 no. fixture as per
attached detail specificaton. Job also includes foundation for the same. Pole to be made up of
100mm dia MS pipe of 3.0 m length, 80mm dia MS pipe of 3.0m length and 50mm dia pipe of
1.0m length with 65mm dia cap, gusset plats, etc.,complete. Rates to include excavation, PCC,
RCC and reinforcement, etc. complete
DOUBLE ARM MS POLES
Same as above but with double arm
OCTAGONAL GALVANIZED POLE 6.0 M. HT-SIN
Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height 6.0 meter having
wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12 mm, 500
mm long weatherproof reinforced door opening with junction box mounting arrangement but
exclusive of junction box, single arm bracket 1 m, 20mm dia. threaded made to J shape and
having 600 mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templates and all
complete as per approved drawing. Approved Equivalent Make - PHILIPS
EA
55
EA
68
EA
165
EA
140
EA
108
MT
95
EA
1030
EA
9962
EA
10250
EA
12350
EA
13200
Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8 nos. 12mm dia.
tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mm c/c as per approved drawing.
This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above
sorrounding ground/driveway level for 200 mm and have slant 63mm dia. PVC sleeve cast insitu
foundation for cable entry as per the drawing. Rates to include excavation, PCC, RCC and
reinforcement, etc. complete
289
OCTAGONAL GALVANIZED POLE6.0 M. HT-DOUB
Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height 6.0 meter having
wall thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12 mm, 500
mm long weatherproof reinforced door opening with junction box mounting arrangement but
exclusive of junction box, double arm brackets 1 m each, 20mm dia. threaded made to J shape
and having 600 mm total length steel grade EN8 foundation bolts - 4 nos with nuts, templates
and all complete as per approved drawing. Approved Equivalent Make - PHILIPS
Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1200 mm with 8 nos. 12mm dia.
tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mm c/c as per approved drawing.
This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above
sorrounding ground/driveway level for 200 mm and have slant 63mm dia. PVC sleeve cast insitu
foundation for cable entry as per the drawing. Rates to include excavation, PCC, RCC and
reinforcement, etc. complete
290
GI OCT POLE-SNGL ARM 7M
Supply and installation of BAJAJ make Hot dip galavanised iron poleof Height 7.0 meter wall
thickness 3 mm. C/s A/F - top = 70mm, bottom =130 mm, base plate 220x220x12 mm, 500 mm
long weatherproof reinforced door opening with junction box mounting arrangement but
exclusive of junction box, double arm brackets 1 m each, 20mm dia. threaded made to J shape
700 mm long steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as
per approved drawing. Approved Equivalent Make - PHILIPS.
EA
13400
EA
14500
EA
15500
EA
16000
EA
7500
EA
3950
Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1400 mm with 8 nos. 12mm dia.
tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mm c/c as per approved drawing.
This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above
sorrounding ground/driveway level for 200 mm and have slant 63mm dia. PVC sleeve cast insitu
foundation for cable entry as per the drawing. Rates to include excavation, PCC, RCC and
reinforcement, etc. complete.
291
292
293
294
295
GI OCT POLE-DBLE ARM 7M
Same as above but for Double Arm
GI OCT POLE-SNGL ARM 8M
Supply and installation of BAJAJ make Hot dip galavanised iron pole of Height 8.0 meter wall
thickness 3 mm. C/s A/F - top = 70mm, bottom =135 mm, base plate 225x225x16 mm, 500 mm
long weatherproof reinforced door opening with junction box mounting arrangement but
exclusive of junction box, singler arm bracket 1 m, 20 dia threaded made to J shape 750 mm
long steel grade EN8 foundation bolts - 4 nos with nuts, templates and all complete as per
approved drawing. Approved Equivalent Make - PHILIPS.
Foundation RCC 1:1.5:3 shall be of size 550x550mm and depth 1500 mm with 8 nos. 12mm dia.
tor bars as main bars and 8mm dia. tor bars stirrups @ 190 mm c/c as per approved drawing.
This reinforcement shall conform to IS:1786 latest edition. The foundation shall extend above
sorrounding ground/driveway level for 200 mm and have slant 63mm dia. PVC sleeve cast insitu
foundation for cable entry as per the drawing. Rates to include excavation, PCC, RCC and
reinforcement, etc. complete.
GI OCT POLE-DBLE ARM 8M
Same as above but for Double Arm
STREETLIGHT FITTING CRP330/250
Supply and fixing Philips make Cat. CRP 330 street light fixture (IP65) with Ceramic Discharge
CDMTT 250W lamp (Make Philips/ Osram) and single piece die cast aluminium housing with all
accessories energy efficient copper ballast, heat resistant toughened flat glass cover, electronic
ignitor, reflector' power factor improvement capacitor etc. complete. Approved equivalent of Bajaj
make Aqua Wave Series Cat. BGWRL 250 MH SE FFG with 250 W Ceramic Discharge CDMTT
lamp and approved equivalent of Crompton make MHSGT1215IH/G with Lamp 250WCDM-TT .
Approved equivalent of WIPRO make cat no: WST 25250 1X250 W. The job includes fixing the
street light fixtures, providing flexible wire of 7/20 copper wire of approved make, from junction
box to top of the pole.
HOARDING LIGHT QVF 135/70
Supply and fixing Philips make Cat. QVF 135 hoarding light fixture (IP54) with Metal Halide
MHN-TD 70W lamp, control gear box, light weight corrosion-resistant pressure die cast housing
with universal mounting bracket, all accessories energy efficient copper ballast, heat resistant
toughened glass cover, electronic ignitor, reflector, power factor improvement capacitor etc.
complete. Approved equivalent Crompton make Cat. TH 6 MH(DE). The job includes fixing the
street light fixtures and wiring as approved.
296
FIXING OF STREET LIGHT FITTING
Fixing of street light fixture including providing flexible wire from junction box to top of the pole
EA
459
297
EARTHING PIT-PLATE ELECTRODE
Providing plate electrode earthing as per IS 3043 and attached drawing including excavation of
depth 3.2 m, supplying and fixing plate electrode of size 600x600 mm and thickness 6.3 mm (GI)
or 3.15 mm (Copper), 50mm dia GI pipe of heavy duty (wall thickness 4.5 mm) with funnel for
watering, wire mesh, GI flat (2 nos. 50x6 mm ) collars, two connecting GI strips (50x6 mm) from
plate electrode to collar, fixing & using using GI nut bolts with bitumen coating and welding as
per drawing, filling the pit with alternate layers of charcoal and salt, back filling, constructing 230
mm thick Brick Masonry chamber 1000(length)x500(width)x600 (depth) mm internal size with
plastering 10 mm thick and embedded 50 mm dia PVC conduit openings at two places packed
with jute soaked in bitumen at the entrances, 100mm thick PCC 1:3:6 at the bottom of chamber,
providing 3 mm thick MS sheet cover with diagonal bracings of 25x3 mm flats, frame and hinge
arrangement covering full opening, grouting the cover frame in PCC 1:2:4 bed 230x75 mm,
painting two coats of approved colour synthetic enamel paint over a coat of red oxide primer etc.
complete.
Rate includes carrying out earth resistance testing of the earth pit provided, submitting report
and painting resistance, test date and pit identification no. on cover top.
PLT ERTH W/O CHAMBER&COVER
Earthing Pit-Pipe Electrode without chamber:Same as ABOVE item but without chamber and
covers. The item is for providing earthing pit under driveway. The chamber and cover shall be
provided with same specifications as of driveway chambers and as per instructions of Engg.-InCharge. The driveway chambers shall be paid as per respective item rate.
EA
7560
EA
3250
EARTHING PIT- PIPE ELECTRODE
Providing pipe electrode earthing as per IS 3043 and attached drawing including excavation of
depth 3.75 m, supplying and fixing pipe electrode of size 50 mm dia heavy duty (wall thickness
4.5 mm) GI pipe with funnel for wateing, wire mesh, GI flat (50x6 mm) collar joined to pipe using
50x6 mm strip and GI nut bolts with bitumen coating as per drawing, filling the pit with alternate
layers of charcoal and salt, back filling, constructing 230 mm thick Brick Masonry chamber
400(length)x400(width)x400 (depth) mm internal size with plastering 10 mm thick and
embedded 50 mm dia PVC conduit openings at two places packed with jute soaked in bitumen
at the entrances, 100mm thick PCC 1:3:6 at the bottom of chamber, providing CI cover with CI
frame in hinge arrangement covering full opening, grouting the cover frame in PCC 1:2:4 bed
230x75 mm, painting two coats of approved colour synthetic enamel paint over a coat of red
oxide primer etc. complete. Rate includes carrying out earth resistance testing of the earth pit
provided, submitting report and painting resistance, test date and pit identification no. on cover
top.
PIPE ERTH W/O CHAMBER&COVER
Earthing Pit-Pipe Electrode without chamber:Same as ABOVE item but without chamber and
covers. The item is for providing earthing pit under driveway. The chamber and cover shall be
provided with same specifications as of driveway chambers and as per instructions of Engg.-InCharge. The driveway chambers shall be paid as per respective item rate.
EA
6800
EA
3900
NAME PLATE FOR EARTH PIT
Proding/Fixing of MS name/ID plate for earthing pit including painting etc as per the prevailing
norms of IS/BIS / as per the direction of EIC. Size 300mmX200mm and 1.2 mm thick with MS
flat/square bar for grouting.
10 SWG COPPER WIRE
Supply and fixing 10 SWG copper wire for earthing connection to pumps, canopy columns etc.
EA
425
MT
66
MT
325
298
299
300
301
302
303
GI FLAT-50X6 MM
Supply and fixing 50x6 GI flat for earth connection of panel / interconnection of earth pits.
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
GI FLAT - 25X6 MM
Supply and fixing 25x6 GI flat for earth connection
GI FLAT-25X3MM
Supply and fixing 25x3 GI flat for earth connection
CU FLAT -25X3MM
Supply and fixing 25x3 GI flat for earth connection
MS CHEQURED PLATE
Providing and fixing 6mm thick MS chequered plate including making holding arrangements,
painting with two coats of red oxide primer and two coats of synthetic enamel paint etc.
MS CHANNEL/ANGLE EDGE PROTN.
Providing and fixing MS angle/channel supports and edge protection for trench etc. including
providing hold fast ,painting with two coats red oxide primer and two coats of synthetic enamel
etc.
3CX1.5SQMM COPPER WIRE
Supply, laying of PVC insulated, unsheathed multistranded, FLRs copper wire through PVC
conduits or on walls with saddling etc., complete.Size 3Core X 1.5 sqmm
2CX1.5SQMM COPPER WIRE
Same as above but size 2 Core X 1.5 sq mm
4CX2.5SQMM COPPER WIRE
Same as above but size 4 Core X 2.5 sq mm
5PAIR TEL WIRE
Supply and laying of 5 pair telephone wire of approved make
CO-AXIAL CABLE
Supply and laying of co-axial cable of approved make
PVC CONDUITS HEAVY DUTY Supply and fixing of heavy duty PVC conduits of following dia
approved make including all accessories like PVC sockets, bends, junction boxes, etc., joining
by using proper solution, saddling, clamping, etc, complete.
25MMDIA HEAVY DUTY PVC CONDUIT
PVC CONDUITS HEAVY DUTY Supply and fixing of heavy duty PVC conduits of size 25 mm
diameter approved make including all accessories like PVC sockets, bends, junction boxes, etc.,
joining by using proper solution, saddling, clamping, etc, complete.
32MMDIA HEAVY DUTY PVC CONDUIT
Same as above but size 32 mm diameter
40MMDIA HEAVY DUTY PVC CONDUIT
Same as above but size 40 mm diameter
SINGLE POLE MCB
MCB Supply and fixing of single pole MCB of approved make from 6 to 32 Amps including
providing and fixing metal boxes, termination, etc, complete.
DOUBLE POLE MCB
MCB Supply and fixing of double pole MCB of approved make from 6 to 32 Amps including
providing and fixing metal boxes, termination, etc, complete.
TRIPLE POLE MCB
MCB Supply and fixing of triple pole MCB of approved make from 6 to 32 Amps including
providing and fixing metal boxes, termination, etc, complete.
METAL HALIDE LIGHT
Supply and fixing of 150W metal halid canopy light fixtures with lamp and all accessories like
choke, gearbox, ignitor etc, and mounting the same on false ceiling etc., complete. Wipro Cat.
Code WCT15150 or equivalent.
ISI MARKED RUBBER MAT-12MM
Supply and fixing 12mm thick ISI marked rubber mat of approved make.
CVCF -15 KVA
MT
175
MT
95
MT
350
KG
59
KG
55
MT
53
MT
50
MT
68
MT
75
MT
82
MT
25
MT
35
MT
39
EA
174
EA
383
EA
717
EA
5428
SM
902
EA
164791
Supply , installation and commissioning of 3 phase AIR cooled balanced / unbalanced load
Constant Voltage Constant Frequency Volatge Stabilizers (Make - Logicstat / Blue bird / Bhurji /
Techno Vision / Numeric or HPCL approved make) including auto / manual control, overload trip
relay, low / high voltage cut-off, single phase protector, cost of oil. Rate includes making input
and output connection but excludes supply of necessary cables, lugs and clamping. Party to
furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a
period of one from the date of installation. Detailed specifications are as under:
Input freq range 45 Hz to 55 Hz
Accurate output voltage 240vac +/-3% line - neutral
Accurate output freq 50Hz+/-0.1% (crystal controlled)
Output power factor 0.8 lagging to Unity
DC Bus Voltages 360 VDC to 408 VDC
Unmatched transient response For 100% step load change output stays within +/-5% and
recovers within 5 msecs.
Latest technology Micro- controller based PWM, IGBT
Output waveform Pure sine wave
Output overloading : 100% continuous, 120% 15mins, 150% 30secs
Crest factor 5:1 suitable for inductive load like motors.
Inverter efficiency Greater than 90%
Transfer time Continuous inverter “on” no change overtime
Operating temp 0 TO 55 deg C
Humidity range 95% Rh (non condensing)
Total harmonic distortion Less than 2% at linear load less than 5% at non-linear load
Isolation Total isolation of output from input to protect from spicks and surges
Genset compatible : Yes
Alarms warning Mains fail, Batt low, DC over, DC under, o/p AC over, O/p over load, O/p AC
under
User friendly monitoring Indication: Mains on, Inverter On, Batt. Low, Inv trip, Bypass
Audible noise Less than 60 db at 1 meter
By pass Manual bypass provided
Battery charger Charger is designed on CVCC principle to keep batteries in long life condition
Cooling facility Forced air cooling
Safety protections: Output over/under voltage,Output overload, Output short circuit,
DC over/under voltage, Input phase fail
323
3 PHASE SERVO STABILISER-40 KVA
Supply , installation and commissioning of 3 phase AIR cooled balanced / unbalanced load
servo controlled voltage stabiliser of 40 KVA (Make - Logicstat / Blue bird / Bhurji / Techno
Vision or HPCL approved make) including auto / manual control, overload trip relay, low / high
voltage cut-off, single phase protector, cost of oil. Rate includes making input and output
connection but excludes supply of necessary cables, lugs and clamping. Party to furnish
manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a period of
one from the date of installation. Detailed specifications are as under:
EA
116323
Specifications 3 Phase
1. Input Voltage 300 - 460 VAC
2. Output Voltage 415 VAC
3. Operating frequency 50 HZ
4. Output Voltage Regulation +/- 1%
5. Response time < 3 msecs
6. Rate of Correction 12 to 60 V / Sec
7. Efficiency > 98%
8. Wave form Distortion Nil
9. Effect on Power Factor Nil
10. Operating Temperature 10 – 60 Degree C
11. Duty of operation Continuous at 100%
12. Cooling Forced Air Cooling
PROTECTIONS
UNDER / OVER VOLTAGE Contactor/MCCB
Short Ckt
Over Load Protection MCB/ MCCB
Single Phasing Preventer Not required
Neutral Lift Protection Optional
EMI/RFI filters Optional
By Pass Switch Required rotary bypass
INDICATION
Mains On Required
Under/Over Voltage Required
Voltmeter 0 – 500 VAC
AMP meter Required
Alarm Optional Optional
Output voltage setting It should be possible to set the output voltage from the front panel
324
325
326
327
328
329
3 PHASE SERVO STABILISER-30 KVA
Same as above but rating 30KVA
3 PHASE SERVO STABILISER-25 KVA
Same as above but rating 25KVA
3 PHASE SERVO STABILISER-20 KVA
Same as above but rating 20KVA
3 PHASE SERVO STABILISER-15 KVA
Same as above but rating 15KVA
3 PHASE SERVO STABILISER- 10 KVA
Same as above but rating 10KVA
1 PHASE SERVO STABILISER- 10 KVA
Supply , installation and commissioning of 1 phase AIR cooled balanced / unbalanced load
servo controlled voltage stabiliser of rating 10 KVA (Make - Logicstat / Blue bird / Bhurji /
Techno Vision /Numeric or HPCL approved make) including auto / manual control, overload trip
relay, low / high voltage cut-off, single phase protector, cost of oil. Rate includes making input
and output connection but excludes supply of necessary cables, lugs and clamping. Party to
furnish manufacturer's test certificate alongwith supply and provide warranty/gaurantte for a
period of one from the date of installation. Detailed specifications are as under:
EA
101783
EA
92089
EA
72702
EA
53315
EA
38774
EA
33928
Specifications 1 Phase
1. Input Voltage 170 – 270VAC
2. Output Voltage 230 VAC
3. Operating frequency 50 HZ
4. Output Voltage Regulation +/- 1%
5. Response time < 3 msecs
6. Rate of Correction 12 to 60 V / Sec
7. Efficiency > 98%
8. Wave form Distortion Nil
9. Effect on Power Factor Nil
10. Operating Temperature 10 – 60 Degree C
11. Duty of operation Continuous at 100%
12. Cooling Air Cooling
PROTECTIONS
UNDER / OVER VOLTAGE REQUIRED
Over Load Protection MCB
INDICATION
Mains On Required
Under/Over Voltage Required
Voltmeter 0 – 300 VAC
AMP meter Optional
Alarm Optional
330
331
332
333
334
1 PHASE SERVO STABILISER- 7.5 KVA
Same as above but rating 7.5 KVA
1 PHASE SERVO STABILISER-5 KVA
Same as above but rating 5 KVA
1 PHASE SERVO STABILISER-3 KVA
Same as above but rating 3KVA
1 PHASE SERVO STABILISER-2 KVA
Same as above but rating 2 KVA
250 VA CVT
CVT Supply and fixing of constant voltage transformer of aproved make - Logicstat, Blue bird,
Sukam, Bhurji , Numeric or equivalent. Party to furnish manufacturer's test certificate alongwith
supply and provide warranty/gaurantte for a period of one year from the date of installation.
Rating 250 VA rating
EA
24234
EA
17448
EA
12602
EA
9209
EA
3005
EA
4508
EA
7561
EA
9984
CVT Technical Specifications
Input Voltage 180 to 260V AC/1 Ph/50±2Hz
Output Voltage 220VAC/230VAC±1%
Frequency Effect Approx. 1.5% change in output voltage, for 1% change in input frequency
Efficiency 90%, Typical, at full load
Common-Mode-Noise Attenuation* 1:3000, Typical
Normal-Mode-Noise Attenuation* 1:2500, Typical
Output waveform Sinusoidal
Total Harmonic Distortion 5% (Typical) at 230VAC-Input & full-load change
Output Voltage Correction 2 cycle (max.) for no load to full load conditions
Over Load protection To be provided
Operating Temperature 0ºC to +50ºC
Operating Humidity 95% RH, non condensing
Metering 0-300v, M.I. meter; Accuracy ± 2% FSD (To monitor output voltage)
Environment 0-40°C, 95% RH (non condensing)
335
336
337
500 VA CVT
Same as above but rating 500 VA
750 VA CVT
Same as above but rating 750 VA
1000 VA CVT
338
339
340
Same as above but rating 1000 VA
1500 VA CVT
Same as above but rating 1500 VA
2000 VA CVT
Same as above but rating 2000 VA
GSB LAYER
Filling material with GSB (Granular Sub Base) of 30 cm thick:: The GSB shall consists of the
following material
40 to 53MM Size metal : 40%
20 to 40MM size metal 20%
10 to 20MM size metal 20%
0 to 10MM size metal 20%
Job shall include supply and filling GSB materials in two compacted layers of 150 MM each.
Payment shall be released on the compacted layer provided by the vendor at site. Compaction
shall be carriedout only with Vibro roller of required capacity . Contractor has to obtain
necessary clerance from HPCL or its autorised reprensatative for first layer. Only after obtaining
the second layer GSB shall be provided. Job includes all me material and transporation cost of
the required to be completed as per the directions of the HPCL
EA
14201
EA
19193
SM
263
341
WBM 1ST LAYER 100 mm thk.
WATER BOUND MACADUM Providing and laying WBM in 100mm thick compacted thickness
each using well graded stone aggregates of approved quality of 90 to 45 mm size with screening
of 13.2 mm & less. Rate includes spreading metals, hand packing, filling the interstices with
spalls, chips, and approved quality binder and rolling each layer with 10 MT power roller with
simultaneous watering till the metal is bound by the water binder paste to achieve maximum
compaction, finishing the surface to
proper grade and level .Rate also to include carrying out the following tests on aggregates and
test results to be submitted to EIC before use and shall meet following strength requirements.[LA
Abrasion value : 40 % , Flakiness Index :15 %]
SM
107
342
WBM 2ND LAYER 75 mm thk.
Second Layer 75 mm thick using 63 to 40mm size stone aggregate with screening of 13.2 mm &
less.
WBM 3RD LAYER 75 mm thk.
Third layer of 75mm thick using 53 to 22.2 mm size stone aggregate with screening of 13.2 mm
& less
SEMI DENSE BITU.CONC. 25MM THK
SEMI DENSE BITUMINOUS CONCRETE (25 mm Thick) : Providing and laying 25 mm thick
semi dense bituminous concrete on prepared surface with good quality graded stone aggregate
as per following requirement -Material 5euired per 100 Square meter Crushed stone aggregate
of 13.2 mm size = 1.0 CUM , 11.2 mm size -1.6 CUM , Fine aggregate 6 mm size - 1.1 CUM
Bitumen 60/70 grade including tack coat = 330 Kg .The job includes hot mixing of aggregate and
bitumen by using hot mix plant transportation mixed material and laying the same , rolling with 8
to 10 Ton power roller to uniform consolidated compacted thickness of 25 mm over a tack coat
of 2.0 Kg per 10 Square meter to achieve the required level and grade all material, labour etc
complete.
SEMI DENSE BITU.CONC. 40MM THK
SEMI DENSE BITUMINOUS CONCRETE (40 mm Thick) : Providing and laying 40 mm thick
semi dense bituminous concrete on prepared surface with good quality graded stone aggregate
as per following requirement: Material per 100 Square meter Area - Crushed stone aggregate of
13.2 mm size = 1.60 CUM; 11.2 mm size -2.56 CUM; Fine aggregate 6 mm size - 1.76 CUM;
Bitumen 60/70 grade including tack coat = 525 Kg .The job includes hot mixing of aggregate and
bitumen by using hot mix plant transportation mixed material and laying the same , rolling with 8
to 10 Ton power roller to uniform consolidated compacted thickness of 40 mm over a tack coat
of 2.0 Kg per 10 Square meter to achieve the required level and grade all material , labour etc
complete .
SEMI DENSE BITU.CONC.100MM THK
SEMI DENSE BITUMINOUS CONCRETE (100 mm Thick) : Same as above but with thickness
of 100 mm.
MASTIC WEARING COARSE 25MM
SM
80
SM
80
SM
263
SM
430
SM
870
SM
700
343
344
345
346
347
MASTIC WEARING COARSE (25 mm Thick): Providing and laying 25 mm thick mastic wearing
coarse using stone aggregates as per following specs- Coarse aggregated to be used 35% of
total mix , Balance shall be coarse sand and filler material, Lime stone powder and industrial
bitumen of grade85/25 confirming to IS 702 prepared by using Mastic cooker and laid to required
level and slope including providing anti skid surface with bitumen precoated fine grain chipping
of 9.5 mm to 13.2 mm size at the rate of 0.005 CUM per 10 square meter of approx. spacing of
10 cm center to center in both directions , pressed into surface protruding 1mm to 4 mm over
mastic surface including cleaning the surface removal of debris etc. material and labour
complete. NOTE : Lime stone powder shall have minimum calcium carbonate content of 80 %.
348
349
350
351
352
FIBRE REINFOR. CONCRETE COVER
Suppy and laying in posion of Precast slab shall be of FRC ( Fibre reinforced Cconcrete) of
20MT load bearing capacity, dimention 750X450x150 MM, with 12mm dia plain round bar for
lifting the cover fiited with plastic cups. The slab shalll be manufactured as per IS code: 12592
(part-1, 1988 & Part-2, 1991) and shall comply with following: requirements:
Mechanised production through vibration pressing techniques
Manufactured with concrete mix of minimum M 300 grade
Top surface of the cover shall be ebosed with checkered design for safety agains hazards of
slipping.
Cover shall be designed to prevent jamming of covers in frames
The slabs shall be provided with lifting bars for easy handling duly protected against currossion.
Necessary Manufacturer test certificate, copy of invoice tec etc shall be submitted by the vendor
conformimg the above requirements
THERMOPLASTIC ROAD MARKING
Supplying and applying Berger make Sigmark thermoplastic road marking paint( yellow in color)
as per MORTH specifications 803.4. The work shall be carried out strictly in line with
maufacturer's procedures and using specified materials, tools, heating device/apparatus and
machinery etc. all complete. The briefs of materials are as following:
(i) Hot Melt Thermoplatic Road Marking Compound: 5 kg/sqm
(ii) Glass Beads: 250 gm /sqm
The drying time should be within 5 minutes and dry coat thickness to be 2.5 mm.
Rate shall be inclusive of all material, labour, tools & tackles, power, heating apparatus etc. all
complete. Work shall be carried out ensuring safety at outlet and as per approved drawing and
plan.
RAISED PAVEMENT MARKERS
Providing and fixing 3M make adhesive type heavy duty high performance raised pavement
markers with shanks (Glow Stubs) made of Engineering Polymer in size 101x89mm with height
20mm having retroreflective element on both sides and to be fixed on cement concrete rigid
pavement with adhesive/shanks as recommended by manufacturer and interspacing as per
Engg.-in-Charge approval. Rate includes necessary before/after cleaning, tools and tackles etc.
all complete
LINEAR DELINEATION SHEETING
Providing and fixing 3M make Linear Delineation Sheeting (LDS) comprising of panels of size 4"
wide and 33" length in yellow colour. The panel is to be constructed of cube corner Retro
Reflective Material bonded to Aluminium substrate with memmed lateral edges. The panel
assembly shall have a repeating raised lateral ridge every 2.25 inch, 0.34 inch in height. The
typical retro reflective values at 88.5 degree entrance angle / 0.2 degree observation angle to be
270, 162, 11080 (candelas/ meter square / lux) of yellow colour.
The fitting will be done on brick masonry/concrete walls as per manufacturer specified
procedures and approved nails/fixtures in line and level as per advice of Engg.-in-Charge (EIC).
Powder coated MS angle edge protection shall be provided to make it theft resistant.
Measurement and payment shall for per no. of 33inch long and 4" wide LDS provided as per EIC
advice.
MASTERTOP 1332
SM
3900
SM
950
SM
475
SM
3790
SM
2900
Supplying, painting/laying Degussa make Polyurethane based multi – component decking
system for heavy abraison areas including material, machinery, tools and tackles, power etc. all
complete following manufacturer specified procedures. The brief of constituent layers/coats are
as following, the last being the topmost layer: Mastertop 1332
MTOP 1200 plus primer @ 0.3 kg / sqm; Mastertop SRA No. 3 sand scatter @ 0.6 kg/sqm;
Mastertop Membrane 23 @ 0.5 kg/sqm; Mastertop SRA No. 3 sand scatter @ 1 kg/sqm and
TWO COATS of Mastertop TC 458 of colour French/HP blue (Colour Code BS 166) @ 0.4 kg /
sqm each coat i.e. total 0.8kg/sqm. Each layer will be given generally one day set period as per
manufacturer's specifications. Traffic will not be allowed in the area from very first layer
application till setting of top coat. It shall be vendor's responsibility to ensure that proper
application for each layer is done with sufficient time. In case the vendor fails in ensuring proper
application and setting time, rectifications shall be done without extra cost as per manufacturer
specified procedures and as agreed by Engg.-in-Charge in writing.
353
354
355
356
357
358
359
The vendor shall furnish 5 years repalcement guarantee on Rs.100/- stamp paper against
defects, damage under vehicular traffic, wear and tear etc. from the completion date. HPCL
descrition shall be final and binding on the vendor.
PREMIX CARPET-50 MM
Providing and laying premix carpet 50 mm thick ( Consolidated) with coarse aggregate of
nominal size 12.5 mm ( two part ) and 10 mm ( one part) . Quantity of bitumen (80/100 grade)
used should be 36.5 Kg per 10 sqm for premix and 7.5 kg per 10 sqm for tack coat. Surface
preparation by cleaning with wire brush, removing the dust etc before applying tack coat. The job
includes compaction by 8 to 10 Ton roller to proper camber and slope all complete as per
direction of Engg.-In-Charge.
PREMIX CARPET-100 MM
100mm thick carpet : Specification same as above item but two layers of 50mm thick each.
SEAL COAT 12 MM
Providing and laying seal coat of 12 mm thick with 6.3 mm down coarse aggregate. Quantity of
bitumen used should be 19.6 Kg per 10 square meter of seal coat . The job includes compaction
by 8 to 10 Ton power roller to proper camber and slope all complete as per direction of Engg.-InCharge. Finishing should be done by applying a layer of sand in order to fill up the voids.
NOTE : All the asphalting jobs shall be started only after stacking bitumen at the site as per
theoretical calculation considering the area. The total job including seal coat to be carried out in
one go. In case of any delay in laying the seal coat after laying the premix carpet, additional tack
coat @ 5.0 Kg per 10 sqm to be laid without any extra payment.
BBM
Providing and laying bitumenous bound macadum surface 100 mm thick after compaction
including supplying all materials spreading 40 mm size trap metal layers and key aggreagates
heating and spraying bitumen of grade IS grade S-65 with penetration 60/70 at the rate of 400
kg/100 sqm and compacting after finishing by 6mm thick layer of grit to the satisfaction of the
engineer with a roller not less than 10 MT.
S/L DRIVEWAY GREY PAVER M-40
Supply and laying of 80mm thick grey pavers in line and level and approved pattern and shape,
as per attached specifications. The job includes supplying and laying sand bedding, compacting
using plate vibrator, all material and labour complete. Pavers will be laid in specified pattern.
Plan of laying will be developed by the contractor and prior approval of EIC will be taken before
commencement of laying. The pavers supplied should qualify min comp. strength of 47.2MPa
and should conform to IS:15658:2006. The party shall have to produce manufacturer's
certification on the paver qualifying criteria stated in IS-15658 and limits specified in the attached
specification before the pavers are sited. HPCL reserves the right to do random sampling and
testing as per IS-15658:2006 to assess manufacturer's certification on qualifying norms specified
in the attached specification. The testing charges, if samples qualify, shall be borne by HPCL,
else shall be borne by the party.
S/L DR.WAY COLOUR PAVER M-40
Same as above but coloured paver
S/L REFL. GREY D/W PAVER M40
SM
280
SM
433
SM
145
SM
245
SM
610
SM
640
SM
640
360
361
362
363
364
365
366
Same as above but reflective coloured paver. The top layer shall have 10to 15mm uniform
thickness made out of Granite/Quartz crushed aggregated of cubical sizes not more than 6 mm
& downsize (shall have good abrasion resistant properties) as wearing layer & reflective coating
& cement shall be mixed with UV resistant pigment & colour as per HPCL's selection & without
impairing the characteristic properties of cement. Top surface shall be made anti skid
(indentations) with lacquer coating finish.
S/L REFL. COLOURED D/W PAVER M40
Same as above but coloured paver
S/L GRASS PAVERS MIX M-40
Specifications same as item no. 434 but for grass pavers. Grass pavers shall be of 80 mm
thickness and shape corner-cut square made out of 500x500 mm size with all the four corners
cut in quarter size circles of 125 mm radius. Four nos. of such pieces laid in symmetrical square
pattern will give total opening area of 0.196 sqm. The circular openings so formed shall be
planted with grass. Supply and laying of grass is not included in the scope but filling of these
openings with same sand fully compacted and vibrated is included in the scope.
S/L PEDESTRIAN PAVERS MIX M-25
Specifications same as item no. 434 but for 40 mm thick wedge wood (flag) unipavers made
from M 25 grade concrete in 1 red and 2 grey combination for walkways and light load areas as
advised by EIC .
RELAYING OF PAVERS
Laying of HPCL supplied/existing old pavers in line and level , as per attached specifications.
The job includes supplying and laying sand bedding, compacting using plate vibrator, all material
and labour complete. Pavers will be laid at 45 degree to road line in 1 red and 2 grey
arrangement. Plan of laying will be developed by the contractor and prior approval of EIC will be
taken before commencement of laying..
PRECAST KERB 300X150X450
RCC PRECAST KARB 0.3X0.15X0.45: Providing and erecting kerb wall of concrete precast
kerb of required size & shape with M20 grade concrete using 20mm and down size crushed
stone aggregates including shuttering, mixing, compacting , pond curing for 14 days etc. as per
IS 456 with 100X100 size sunk of retro-reflective paint of approved shed as per the details,
transporting from the place of casting, errcting the wall with filling the joints with necessary
cement slury etc. complete .
PRECAST KERB 300X150X300
RCC PRECAST KARB 0.3X0.15X0.30 : Providing and erecting kerb wall of concrete precast
kerb of required size & shape with M20 grade concrete using 20mm and down size crushed
stone aggregates including shuttering, mixing, compacting , pond curing for 14 days etc. as per
IS 456, transporting from the place of casting errcting the wall with filling the joints with
necessary cement slury etc. complete .
TREMIX RCC 1:1.5:3 DRIVEWAY
Providing and laying 150mm/ 200 mm thick RCC driveway with 1:1.5:3 nominal mix using 20mm
and down size crushed stone aggregates in panels using slotted MS channel shuttering,
machine mixing, vibrating with screed board vibrator, pond curing for 14 days, vaccum
dewatering, finished with power trowelling. Concreting shall be carried out as per IS 456.
Rate shall also include providing approved quality polythene paper below the driveway,
constructing horizontal and longitudinal vatas with 1:10 CM for curing, levelling depressions if
any in the base with 20mm stone aggregates and stone dust.
Proper slope to be provided in driveway for easy draining of rain water.Reduced level of the
driveway area to be taken jointly with architect before commencement of concreting and after
concreting and the thickness of RCC to be checked.
Testing of cube, reinforcement steel, stone aggregates, sand, cement etc. to be carried out by
contractor at no extra cost.Tubing, ducting, trenching and other necessary embedded items in
concrete shall be checked with architect/HPCL representative before concreting.Grooves shall
be cut in the RCC driveway and same shall be filled with Bitumen at no extra cost.
The cement consumption for 1:1.5:3 mix shall be 8.5 bags/cum and compressive strength shall
be 170 kg/sqcm and 200 kg/sqcm after 7 days and 28 days respectively.
Rate shall be
excluding reinforcement steel which shall be paid separately .
SM
660
SM
480
SM
400
SM
50
M3
4300
M3
4300
M3
5054
367
368
369
370
371
372
373
374
375
376
377
378
379
TREMIX WITH M-20 READY MIX
Same as above item but using M-20 grade ready mix concrete.
RCC 1:1.5:3 WITHOUT DEWATERING
Same as above item but without vaccum dewatering and power trowelling with 1:1.5:3 nominal
mix
TREMIX RCC DR.WAY-RAP HARD CEM
Same as tremix drive way item but with using rapid hardening cement for the 1:1.5:3 mix
RCC PRECAST SLABS
Providing and laying RCC precast slabs of required size with 1:2:4 nominal mix using 20mm
and down size crushed stone aggregates including shuttering, mixing, compacting , pond curing
for 14 days etc. as per IS 456, transporting from the place of casting . Reinforcent steel shall be
paid separately.
RCC PRECAST COVER
Providing and laying factory made pre-cast RCC (Concrete Grade – MINIMUM M35) covers with
MS lifting lugs of Surabh / KK manhole make having thickness 90 mm and size to cover the
pipeline trench. The cover shall be suitable for AAA class load (Minimum 35 MT rolling axle load)
and shall have MS enclosure of minimum 2 mm thick allaround including reinforcement suitable
for load class. The clear opening span of trench shall not be more than 650 mm.
STEEL REINFORCEMENT
STEEL REINFORCEMENT Supply, fabrication and placing in position High yield strength
deformed bars conforming to IS 1786 - Latest edition grade FE 415 as required and directed at
site for driveway including cutting, bending, placing in position and tying with 20 SWG binding
wire, complete. Quantity shall be measured as per reinforcement drawing and with theoretical
weights including all authorized laps. Unauthorized chairs, spacers and laps will not be
measured and paid for.
600X450X700MM INS. CHAMBERS
INSPECTION CHAMBER Providing and constructing following size inspection chambers with
230mm thick brick masonary in 1:5 cement mortar, excavation, 75mm thick PCC 1:4:8 bed,
plastering with neat cement finish, providing 16 mm thick MS plate cover with 50 x 50 x 6 angle
frame etc. complete. Size 600X450X700 mm
600X600X700MM INS. CHAMBERS
Same as above but size 600X600X700
450X450X700MM INS CHAMBERS
Same as above but size 450X450X700
SURFACE DRAIN
SURFACE DRAIN Providing and constructing surface drain 12" wide and 24" depth (average)
with 9" BBM in CM1:4 with plastering on both sides including excavation, soling, PCC1:3:6,
including giving necessary slope, etc., completed.
DRESSING OF DRIVEWAY
DRESSING OF DRIVEWAY Dressing of existing driveway wherever required including
excavation to required depth and providing/laying metalling upto 3" or as per required thickness
compacted to level desired by ramming, filling up the interstices with stone chips, stone grit
powder as sub-base to fix the paver blocks later including all materials and labour, wherever
necessary as per instruction of HPCL Engineer/Architect.
BITUMINOUS MACADAM 75mm
BITUMINOUS MACADAM 75mm THICK USING 60/70 GRADE BITUMEN: Providing and laying
premix bituminous macadam base course with good quality stone aggregate mix as follow 20mm
= 30%, 12mm=35%,6mm=15% coarse sand 15 % and bitumen 60/70 grade 6% by weight .The
aggregate shall be of quality size and grading as specified and bitumen shall be straight run
bitumen of grade 60/70 @ 6 % by weight of total mix . The job includes hot mixing by using mini
hot mix plant , transporting mix material and laying the same to the required level & grade, rolling
with power roller of 8 to 10 Ton capacity to achieve required compaction and density all material
, labour etc. complete. The macadam course shall be laid in two layers of around equal
thickness, each layer shall be rolled and compacted. Tack coat shall be applied between the
two layers@ 9.8 kg per 10 sqm.
TRANSP. OF 70 KL WITHIN 30 KM
M3
5500
M3
4718
M3
5215
M3
5054
SM
2700
TM
46000
EA
4800
EA
5000
EA
4650
MT
1900
SM
30
SM
450
EA
14500
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
Transportation of 70KL horizontal tanks to site including loading, unloading etc. Complete
upto 30KM from the source
TRANS. 70 KL TANK
Same as above but beyond 30 km
TRANSP. OF 45 KL WITHIN 30 KM
Transportation of 45KL horizontal tanks to site including loading, unloading etc. Complete
upto 30KM from the source
TRANS. 45 KL TANK
Same as above but beyond 30 km
TRANSP. OF 22 KL WITHIN 30 KM
Transportation of 22KL horizontal tanks to site including loading, unloading etc. Complete
upto 30KM from the source
TRANS. 22 KL TANK
Same as above but beyond 30 km
TRANSP. OF 16 KL WITHIN 30 KM
Transportation of 16KL horizontal tanks to site including loading, unloading etc. Complete
upto 30KM from the source
TRANS. 16KL TANK
Same as above but beyond 30 km
TRANSP. OF 9 KL WITHIN 30 KM
Transportation of 9KL horizontal tanks to site including loading, unloading etc. Complete upto
30KM from the source
TRANS. 9KL TANK
Same as above but beyond 30 km
TR.MONODU<30KM IN LOT UPTO 5NO
The quantity will be calculated per trip upto maximum of carrying 5 pumps per trip
TR.MONODU BEY30KM UPTO 5NO LOT
The KM will be calculated per trip upto maximum of carrying 5 pumps per trip
TR.DUAL/2T DU<30KM-LOT UPTO 5 NO
The quantity will be calculated per trip upto maximum of carrying 5 pumps per trip
TR.DUAL/2T DU BEY30KM-TO 5NO LOT
The quantity will be calculated per trip upto maximum of carrying 5 pumps per trip
TR. MPD<30 KM IN LOT UPTO 5 NO
The quantity will be calculated per trip upto maximum of carrying 5 pumps per trip
TR.MPD BEY30 KM IN LOT UPTO 5 NO
The quantity will be calculated per trip upto maximum of carrying 5 pumps per trip
45 KL TANK INSTALLATION
Installaion of HPCL supplied Tanks of 45KL capacity in earth pit /under driveway including
lowering, providing holding down arrangement, Hydrostatic testing to pressure of 5psi, supplying
& filling with water with necessary 50 mm dia pipe & on successful completion emptying out the
water from tank , cleaning & drying the inner surfaces with cloth/ cotton waste etc., doping with
three coats of shalimastic HD over a coat of GETSET (Type-A) primer with minimum thickness of
1.5mm. 24Hrs drying time between each coat has to be maintained.
KM
45
EA
9500
SM
35
EA
3060
KM
29
EA
2959
KM
29
EA
2450
KM
27
LOT
1400
KM
25
LOT
1550
KM
25
LOT
1650
KM
37
EA
22000
22KL TANK INSTLN.
Same as above but size 22 KL
16KL TANK INSTLN.
Same as above but size 16 KL
9KL TANK INSTLN.
Same as above but size 9 KL
SS RAILING FOR PUMP ISLANDS
Fabricating and fixing S. S. Railing with 40 mm SS square tube & 25 mm dia SS pipe ( SS of 202
grade) as per the drawing. The item includes fabrication, buffing of the railing upto req. finish,
fixing the railing at position with m20 grade concrete, finising the driveway properly etc. complete
EA
14000
EA
11500
EA
10500
EA
8000
CHRO.PLATD MS PUMPISLAND GUARD
EA
7500
401
402
403
404
405
406
407
408
409
410
411
412
413
Fabricating and fixing cromium plated MS Railing with 50 mm DIA and 40 mm dia B CLASS MS
pipes of Swastik/Jindal/Zenith make as per the Standard HPCL drawing. The item includes
fabrication, buffing of the railing upto req. finish, fixing the railing at position with m20 grade
concrete, finising the driveway properly etc. complete
PUMP ISLAND
Construction of pump island 1m wide with 230mm thick brick masonry in CM 1:5, 12mm thick
plastering in Cm 1:4 roughened to receive granite tiles including excavation, 75mm thick PCC
1:4:8 , sand filling and constructing the wall 400mm above the finished driveway level and
600mm below the finished driveway level .
INSTLN. OF MONO PUMPS
Installation of MONO pumps on pedestal including providing & fixing foundation bolt of 12mm dia
& connecting suctionpipe, electrical, earthing connections to the pump.
INSTLN. OF DUAL/2T MIX PUMPS
Installation of DUAL pumps on pedestal including providing & fixing foundation bolt of 12mm dia
& connecting suctionpipe, electrical, earthing connections to the pump.
INSTLN. OF MPD PUMPS
Installation of MPD pumps on pedestal including providing & fixing foundation bolt of 12mm dia &
connecting suctionpipe, electrical, earthing connections to the pump.
Supplying & Laying 'C' Class MS ERW black steel screwed pipeline ( TATA/SWASTIK/JINDAL
make)Conforming to IS 1239 (part I) – latest edition to the required slope & alignment with
heavy duty MS fittings like elbows, tees including doping pipe line with 1.5mm thick layer of
shalimastic HD in 2 coats etc, complete. The joints are to be made leak proof by using jointing
materials like Litharge, Glycerin, Shellac, holdite . The pipeline to be tested with 5PSI as per
standard specification.
40MM DIA PIPELINE
Supplying & Laying 'C' Class MS ERW black steel screwed pipeline (TATA/SWASTIK/JINDAL
make) Conforming to IS 1239 (part I) – latest edition to the required slope & alignment with
heavy duty MS fittings like elbows, tees including doping pipe line with 1.5mm thick layer of
shalimastic HD in 2 coats etc, complete. The joints are to be made leak proof by using jointing
materials like Litharge, Glycerin, Shellac, holdite . The pipeline to be tested with 5PSI as per
standard specification. Size 40 mm Diameter.
MT
1400
EA
565
EA
750
EA
1000
MT
495
50MM DIA PIPEINE
Same as above but size 50 mm Diameter
80MM DIA PIPELINE
Same as above but size 80 mm Diameter
40MM DIA CHECK VALVE
Supply and fixing ISI marked angular check valve of Leader/GG make size 40mm diameter
MT
571
MT
765
EA
1890
50MM DIA CHECK VALVE
Same as above but size 50 mm Diameter
S/F/L MS C CL.WELDED PL2.5"DIA
Supplying & Laying 2.5" Dia Heavy-duty 'C' Class MS Steel ERW Welded P/L (
TATA/SWASTIK/JINDAL make) Conforming to IS 1239 (part I) – latest edition to the required
slope & alignment with heavy duty MS fittings like elbows, sockets,unions , tees etc. including
doping pipe line with 3 coats of 'Shalimastic HD THIXOTROPIC of STP cold applied anti
corrosive treatment after preparing the surface as per manufacturer specifications. The joints
are to be made leak proof. The P/L which would laid aboveground shall be painted with two
coats of synthetic enamel over two coats of Zinc Chromate primer of approved quality and
shade. The pipeline shall be tested at a pressure of 5Kg / sqcm.
EA
2700
MT
875
MT
765
EA
850
EA
775
S/F/L MS C CL.WELDED PL2.0"DIA
Same as above item but with Pipe dia as 2.00"
FLANGE JOINT 2.5" DIA
Supplying & fixing of 2.5 inches dia C Class MS Flanges for Petroleum products of approved
make and of Heavy duty usage.
FLANGE JOINT 2" DIA
Supplying & fixing of 2 inches dia C Class MS Flanges for Petroleum products of approved make
and of Heavy duty usage.
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
P/F BALL VALVES 2.5" DIA
Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.5 inches Dia
P/F BALL VALVES 2.0" DIA
Supply and fixing ISI marked Ball valve of Leader/ Sant/ Syall make. 2.0 inches Dia
INSTALLATION OF STP
Installation of STP pumps on Tank Manhole including connection with suction pipe, electrical,
earthing etc. complete.
4 WAY MANIFOLD
S/fixing of 4-way MS manifold on Tank manhole for providing connection to different dispensers.
EA
5700
EA
5300
EA
1900
EA
5800
MS FILL CAP
Supply and fixing MS fill cap of 80mm dia with locking arrangement including Godrej 6 lever
brass lock
MS DIP CAP
Supply and fixing MS dip cap of 50mm dia with locking arrangement including Godrej 6 lever
brass lock
GRANITE SLAB
Providing and fixing 18-20 mm thick pre polished water cut black granite slab for pump island
top including providing 25mm thk bed cement mortar 1:5 (1 cement : 5 coarse sand) , floating
cement slurry and finishing the joints with white cement mixed with matching colour pigment.
EA
407
EA
275
SM
2908
SM
1550
EA
2000
EA
435
EA
5314
EA
6376
EA
7439
EA
10627
EA
14492
MT
319
M3
556
SM
74
TM
3575
M3
603
GRANITE TILES
Providing and fixing 10 mm thick pre polished water cut black granite tiles for pump island dado
including providing 12mm thk bed cement mortar 1:4 (1 cement : 4 coarse sand) , fixing the tiles
with neat cement paste and finishing the joints with white cement mixed with matching colour
pigment.
SILICA GEL TRAP
Providing and fixing flanged end silica get trap for vent as per standard HPCL design including
filling of silica get crystals, cutting and reconnecting vent pipes, etc, complete.
TEE VENT HOOD
Providing and fixing MS Tee Vent Hood with brass wire guage of 25 mesh/sq.inch as per
standard specification.
EXUMING- 9 KL TANK
Exhuming under ground tanks with all fittings from earth pit including disconnecting suction, fill,
vert pipe , opening man hole cover, excavation, dewatering if encountered, degassing of tank,
stacking the tank as directed by EIC etc.Complete. Back filling with sand will be paid separately.
Size 9KL tank.
EXUMING- 14/16KL TANK
Same as above but for 14/16KL tank
EXUMING- 22 KL TANK
Same as above but for 22KL tank
EXUMING- 45 KL TANK
Same as above but for 45KL tank
EXUMING- 70KL TANK
Same as above but for 70KL tank
DISMANTLING OF P/ISLAND
Dismantling of existing pump island 1m wide and carting away debris including removal of pump
and disconnecting pipeline etc. complete.
DISMANTLING RCC ROOF
Dismantling of RCC roof, beam, column including carting away debris
REMOVAL OF AC SHEET
Removal of AC sheet from roof and stacking as directed by EIC
REMOVAL OF ST. STEEL
Removal of structural steel and stacking as directed by EIC
EXCAVATION IN RCC
Excavation in RCC of any thickness by using pneumatic tools like Jack hammers, chisels or
manually using hammers , chisels etc cutting the reinforcement steel and stacking the same .The
job also includes disposing the dismantled RCC within/outside HPCL premises to any
unobjectionable place all complete as directed by Engg.-In-Charge.
434
435
DIS. OF BRICK MASONARY
Dismantling of brick masonary/PCC /RR masonary including carting away debris
REMOVAL OF FALSE CEILING
Dismantling of all types of ceilings except of bk work/CC, sheets like AC, TRAC, GYPSUM
BOARD etc. Scope of job includes handing over of all 'J', 'L' hooks, nuts and bolts, suspendors
or other joineries in proper bags. Party to ensure joint measurement of the job to be dismantled,
alongwith EIC, before start. Payment shall be made basis the joint measurement, in absence of
any joint measurement record HPCL EIC decision shall be final.
M3
338
SM
34
436
REMOVAL OF MS/AL DOORS
Removal of MS/ Aluminium doors/ windows/fixed glazing and stacking as directed by EIC.
SM
76
437
SHIFTING OF MSEB MAINS
Shifting of MSEB Main, laisoning with MSEB officials, including payment of all incidental charges
etc., all complete ( Payment made to MSEB shall be reimbursed to contractor by HPCL on
submission of original receipt).
REMOVING OF ID SIGN/MASTERPOLE
Removing of existing ID sign carefully without damage and shifting the same or refixing the same
at new place within the primises as per HPCL instructions. Job includes making necessary
electrical connecitons, etc., complete.
TRANSPORATATION OF Q&Q TOWER FROM REGIONAL OFFICE/DEPOT TO THE RETAIL
OUTLET
REMOVAL OF YARD LIGHT POLE
EA
6956
EA
2705
EA
483
EA
2029
LS
2898
REMOVAL OF FENCING
Removing existing chainlink/barbed wire fencing including removing the grouted angles, rods
etc., and stacking the same carefully as directed.
BREAKING OF RCC SLAB
Breaking of RCC slab over tank and driveway by manual means or by using pneumatic breaker
and carting away the debris to unobjectionable place outside RO premises.
REMOVING OF PAVER BLOCK
Removal of existing paver blocks carefully and without damage and refixing the same after the
job completion in proper line and level and compaction etc, complete.
Removing exiting dispensing pumps after disconnecting pipeline, electrical connection etc, and
stacking carefully as directed.
REMOVING OF SINGLE PUMPS
Removing exiting dispensing pumps after disconnecting pipeline, electrical connection etc, and
stacking carefully as directed.
REMOVING OF DUAL/2T MIX PUMPS
Removing exiting dispensing pumps after disconnecting pipeline, electrical connection etc, and
stacking carefully as directed.
REMOVING OF MPD PUMPS
RELAYING OF 40 MM DIA P/L
Relaying of MS threaded pipeline to the required slope of alignment and hydrotesting with the
pressure of 5 psi with providing and fixing necessary MS heavy duty fittings like elbows, tees,
including providing and applying doping the pipeline with shalimastic HD 2 coats. Size 40mm dia
MR
37
SM
164
SM
135
EA
280
EA
386
EA
MT
870
188
RELAYING OF 50 MM DIA P/L
Same as above but size 50 mm Diameter
RELAYING OF 80 MM DIA P/L
Same as above but size 80 mm Diameter
FILL PIPE BRASS COUPLING
MT
232
MT
348
EA
1256
438
439
440
441
442
443
444
445
446
447
448
449
450
451
Removing the existing yard light poles including removing of light fixtures carefully and refixing
the same at designated place within the premises. Job includes excavation, foundation in PCC
1:2:4 with foundation bolts, etc., complete in all respect.
TRIMMING OF TREES
Trimming the branches of trees above a minimum height of 4m from ground level and carting
away the same from the site when and whenever required as per instruction of HPCL
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
Supplying & fixing 75 mm dia Brass coupling for fill point
RUBBER HOSES FOR DECANTING
Tankar unloading Hoses : Supply of eletrically bonded petroleum product unloading hose with
uniform bore of 61mm and 3.3 mtr in length having neoperne rubber of premium quality in outer
cover and acrylic nitrile rubber in inner lining with high degree of flexibility, reinforced with fully
embeded helical wire and static copper wire for eletrically continuty, rubbrer hose should have
outside corrugated without external armouring suitable for handling petroleum products up to
working pressure of 3.5 kg/sqmm and confirming to IS 10733/1983 type 1B with plain ends and 2
nos heavy gun meatal hose nipples with nitrile rubber rings fitted inside and assembled by 2 GI
hose clips to each side of above mentioned hose, supplier to provoide test certificate of eletrical
continuty for each and 6 months Gaurantee againest any manufacturing defects.
EA
4637
INSTN. CLUB HP SIGN (PART-H)
Installing Club HP Signage Board with necessary CC 1:2:4 foundation upto required depth. Job
also supply 4 nos of 12mm dia x 750mm long MS foundation bolts etc, complete.
INSTALLATION - SIGNATURE PYLON
Installing SIGNATURE PYLON Board on the already constructed/existing RCC foundation with
the help of Crane and all the required tools and machinery in proper line and level etc complete.
EA
2367
EA
17390
DISMANTLING - SIGNATURE PYLON
Removal of SIGNATURE PYLON Board from the existing RCC foundation with the help of
Crane and all the required tools and machinery and keeping in safe custody of dealer at the
retail outlet or as directed by EIC.
INSTAL.-MASTERPOLE/CITY PYLON
Installing CITY PYLON/ REGULAR HP MASTERPOLE
Board on the already
constructed/existing RCC foundation with the help of Crane and all the required tools and
machinery in proper line and level etc complete.
INSTLN. OF AIR TOWER
Installing Air Tower facility with necessary CC 1:2:4 foundation of required size and also with
necessary electrical connection.
POSITIONING OF Q&Q TOWER
Positioning of Q & Q Tower Board to shown place with necessary foundation.
FIXING OF WATER COOLER
Fixing of water cooler with necessary electrical connections of 5/15 Amp switch board with
necessary wiring.
P/P OF QUICK CARE POINT
Providing and painting work for Quick Care Point as per standard design.
INST.-INGRESS& EGRESS SIGNAGE
Installing Ingress and Egress Signage Board with necessary CC 1:2:4 foundation and with
necessary electrical connection.
INSTAL OF CREDIT CARD COUNTER
Installing Credit Card Counter with providing and making electrical connections of 5 Amp Switch
socket and telephone socket connection with necessary wiring.
INST.-15 /25/35 KVA GENERATOR
Installation of 15/20/25/30/35 KVA Capacity DG set on AVM pads including shifting from
storage yard to DG room, all cable connection, installation of fuel tank, silenser pipe ,battery
connection, etc. complete.
REMOVAL OF WATER FROM U/G TANK
Removal of Rain water/ sludge etc from Underground tank with the help of manually operated
foot pump/hand pump etc and cleaning the tank from inside. Job includes handling
water/product mixture safely and following all the safety rules during the job.
CONILCAL PARKING STAND
Supply of Plastic Conical Parking stand /Guard of standard height and size or as approved by
the Engineer-In -Charge.
PIPELINE TESTING / REPAIR
EA
7246
EA
6280
EA
2319
EA
850
EA
1159
EA
1159
EA
531
EA
966
EA
4831
EA
3513
EA
1353
EA
2743
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
Testing of pipeline for any leakage with the help of Hydro pressure testing Pressure Gauge ,
identifying the location of the leakage and repairing the line either by replacing the leacky
pipeline or by cutting and reusing the existing line and testing the joint properly at the required
test pressure.Rate to include all the tools/machinery and pipeline material, unions,bends, elbows
etc except check valve.
FIRE EXTINGUISHER -10 KG DCP type
Supply of 10 KG capacity DCP type fire extingisher of approved make(MINMAX/ZENITH/LITEX)
and having ISI mark stamped on cylinder body.
FIRE EXTINGUISHER -7.5 KG DCP type
Supply of 7.5 KG capacity DCP type fire extingisher of approved make(MINMAX/ZENITH/LITEX)
and having ISI mark stamped on cylinder body.
FIRE EXTINGUISHER -4.5 KG CO2 type
Supply of 4.5 KG capacity CO2 type fire extingisher of approved make(MINMAX/ZENITH/LITEX)
and having ISI mark stamped on cylinder body.
FIRE EXT- 75 KG DCP(TROLLEY) TYPE
Supply of 75 KG capacity DCP type TROLLEY FITTED fire extingisher of approved
make(MINMAX/ZENITH/LITEX) and having ISI mark stamped on cylinder body.
FIRE EXT -15 KG CO2(TROLLEY) TYPE
Supply of 15 KG capacity CO2 type TROLLEY FITTED fire extingisher of approved
make(MINMAX/ZENITH/LITEX) and having ISI mark stamped on cylinder body.
CHANGE OVER SWITCH
S/Fixing of 63 A change over switch of L&T / HAVELL'S make
CABLE TRAY-300 MM WIDE
Supply, erection/installation/mounting of 16 SWG 300mm wide perforated GI cable tray inclusive
of cable binding with suitable GI clamps, GI hooks, GI nuts and bolts complete in the tray in a
neat way. The width specified shall be of cable mounting area. Bends at both the sides of cable
tray shall be in addition to it.
CABLE TRAY-150 MM WIDE
Supply, erection/installation/mounting of 16 SWG 150mm wide perforated GI cable tray inclusive
of cable binding with suitable GI clamps, GI hooks, GI nuts and bolts complete in the tray in a
neat way. The width specified shall be of cable mounting area. Bends at both the sides of cable
tray shall be in addition to it.
EARTH PIT MS BOX FOR BUS BAR
Supply and fixing of MS box for earthing pit busbar for keeping heavy duty crocodile clip and
multistranded copper wire used during decantation.
ELEC.SUBMETER-SINGLE PHASE
S/Fixing of MAXWELL / L&T /PIMCO make CT operated , MSEB certified ,Single Phase
electrical sub-meter including necessary electrical connections etc complete.
ELEC.SUBMETER- THREE PHASE
S/Fixing of MAXWELL / L&T /PIMCO make CT operated , MSEB certified ,Three Phase
electrical sub-meter including necessary electrical connections etc complete.
DIP ROD- 3.0 MTR- ALUMINUM
Supply of 3.0 Mtr long Aluminum Dip rod for taking product dip measurements at retail outlet.
DIP ROD- 3.0 MTR- Brass
Supply of 3.0 Mtr long Brass Dip rod for taking product dip measurements at retail outlet.
WATER FLOW SUB-METER- 25 MM DIA
Supply and installation of PCMC/PMC approved/Calibrated water flow meter of 25 mm dia
WATER FLOW SUB-METER- 12 MM DIA
Supply and installation of PCMC/PMC approved/Calibrated water flow meter of 12 mm dia
CLEANING OF VENT PIPE/VENT HOOD
Cleaning of vent pipe and removal of blockage in the form of dust/product. Rate to include
venting out the trapped product /material with the help of compressed air etc complete. Rate to
also include necessary excavation, removal/dismantling of vent pipes and refixing the same after
cleaning of vents.
REPAIRING OF EXISTING BM CHAMBER
Repairing of existing brick masonry chamber inclduing breaking of CC, necessary modification to
the chamber and replstering the inside surface , Making the chamber good to the satisfaction of
EIC.
EA
7608
EA
5024
EA
11159
EA
41543
EA
35747
EA
3381
MR
862
MR
609
EA
2802
EA
4251
EA
5700
EA
1256
EA
3092
EA
2657
EA
1449
EA
2415
EA
1932
TARFELT WATERPROOFING
Supplying and laying of Tarfelt waterproofing by using ISI mark Tarfelt with asphalt primer and
using 30/40 asphalt over the Asbestos Sheet Roofing, etc., complete (5 Course Treatment as
specified by Manufacturer)
GASKET ON TANK MANHOLE
The manhole cover to be fitted with providing and fixing 3mm thick RAF Gasket packing
(Champion make, Champion-59) of 750mm dia.
HEAVYDUTY BRASS CROCODILE CLIP
Supply and fixing of Heavy Duty HPCL approved Brass Crocodile clips at the end of each cable
termination for connecting to the tank lorry during unloading .
TANK MANHOLE MODIFICATION
Modification to the existing underground tank manhole , with the provision of 1 no 75 mm dia
and 1 no 100 mm dia riser pipe for the AUTOMATION purpose. Rate to include removing the
existing manhole from the tank after empting out the tank & complete degassing , covering the
existing tank opening with standby/stepney type manhole and fabricating/cutting/welding the
existing manhole to have above mentioned provisions. Rate to also inlude refixing of the
modified manhole onto the tank with new gasket of approved grade and thickness ( as approved
by HPCL) and supply/fixing of the 75 mm dia MS -C Class pipe ( 10" in length ) and 100 mm dia
MS -C Class pipe ( 8" in length ) on the modified manhole .
SM
362
EA
850
EA
121
EA
6763
488
100 MM DIA GI PIPE
Supplying & Laying 'B' Class Galvanised Iron pipeline of 100 mm dia. (makesTATA/Swastik/JINDAL/Zenith) Conforming to IS 1239 (part I) – latest edition to the required
slope & alignment with heavy duty MS fittings like elbows, tees including doping pipe line with
1.5mm thick layer of shalimastic HD in 2 coats etc, also including cutting, bending & supply and
laying of 17 SWG annealed binding wire inside the HUME Pipe for pulling cables in future etc
complete. The joints are to be made leak proof by using jointing materials like Litharge, Glycerin,
Shellac, holdite . The pipeline to be tested with 5PSI as per standard specification.
MT
725
489
200 MM DIA GI PIPE
Same as above but size 200mm diameter
ROOFING WITH TRACDEK Hi Rib 100
Providing and installing roofing with tracdek Hi Rib 100 or approved equivalent bare Galvalume
high tensile cold rolled steel as per AS 1397 coating class AZ 150 (minimum 150 gm / sqm Zinc Aluminium alloy coating mass total of both sides ) Yield strength 275 Mpa thickness of bare
metal : 0.42 mm ,total coated thickness : 0.47 mm Approximate mass of completed roofing shall
be 4.12 kg /sqm. Rate shall be including providing ridge piece, horizontal /vertical flashing near
illuminated banding.
ROOFING WITH TRACDEK CLIPPON
Providing and installing roofing with tracdek Klippon or approved equivalent bare Galvalume
high tensile cold rolled steel as per AS 1397 coating class AZ 150 (minimum 150 gm / sqm Zinc Aluminium alloy coating mass total of both sides ) Yield strength 275 Mpa thickness of bare
metal : 0.50 mm ,total coated thickness : 0.55 mm etc. Rate shall including providing ridge
piece, horizontal/vertical flashing near the illuminated banding.
18SWG CRCA SHEET WITH POW COAT
Supplying and fixing 18 SWG CRCA sheet with powder coating one side and coat red oxide
primer & two coats enamel paint side for facia to Canopy on the rear sides , ( The sides which
are visible to the road shall be providing with illuminated bands which is covered by a coat of red
oxide primer and two coats of 1st quality synthetic enamel paint one side and poder coating with
HP blue shade on other side. Necessary securely shall be paid separately.
MT
1304
SM
589
SM
744
SM
961
SM
932
EA
5314
484
485
486
487
490
491
492
493
494
18 SWG THICK G I SHEET GUTTER
Providing and fixing 18 SWG thick G.I. sheet Gutters wth 350 gms/sqm of Zinc coating
conforming to clause 7.0 of IS : 277 of any shape in slope with 40 mm x 3mm M.s. Brackets at
1000 mm maximum spacing and 8 mm dia G.I. J or L hooks , boltsand nuts, G,i. Limpet and
bitumen washers , sealing the joints with silicon sealant etc. complete.
CANOPY LIGHT 150 WATT
Supply of 1 x 150 W metal hallide canopy light fixtures with lump WIPRO cat no. WHH 94250 or
equivalent
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
CANOPY LIGHT CFL 85 WATT
Supply of 1 x 85 W Energy saving CFL canopy light fixtures with lamp WIPRO/Crompton/Bajaj or
equivalent
DRILLING 6" DIA BOREWELL
Drilling 5" dia borewell up to requied depth in all kinds of soil including rock using air compressor
rig .Rate to include washing with compressor after installation of casing pipe, providing bentonite
soil if required etc. completed.
6"DIA HDPE CASING PIPE6KG/SQCM
Supply and fixing 5" dia HDPE cashing pipe 6 KG/SQCM presure rating
6"DIA HDPE SLOTTED 6 KG/SQCM
Supply and fixing 5" dia HDPE slotted pipe 6 KG/SQCM presure rating
SINGLE PHASE SUBMER PUMP 1.0HP
Supply and installtion of single phase 1.0 HP submerible pump of kirloskar cat no. KU4- 0709S
discharge range 1.2-8 cum/hr head range 59 -10m along with dry run preventor and starter
SINGLE PHASE SUBMER PUMP 1.5HP
Same as above but size 1.5 HP
32MM NB HDPE PIPE WIPE GI NIPPLE
Supply and installation of 32mm NB HDPE pipe wipe GI nipple at both end
3C X 2.5 SQMM COPPER FLAT CABLE
Supply and laying 3C X 2.5 sqmm copper flat cable
GEOLOGICAL TESTING FOR BOREWELL
Carrying out Geological testing for finalisation of location of borewell
SINGLEPHASE 1HPJETPUMP WITH ST.
Supply and installation of single phase 1 HP jet pump with starter
32MM NB HDPE PIPE&25MM NB HDPE
Supply and installation of 32mm NB HDPE pipe and 25mm NB HDPE pipe with requied
accessories for jet pump.
WATER HARVESTING TYPE I
Providing rain water harvesting type I as per attached drawing internal size 1.5m x 1.5m x 3m
depth from GL.
WATER HARVESTING TYPE II
Providing rain water harvesting type II as per attached drawing internal size 1.5m x 1.5m x 2m
depth from GL. And bore well inside.
DUG CUM BORE/WATERHARV.TYPEIII
Providing dug cum borewell type rain water harvesting type III as per attached drawing with 1.2m
dia 65mm thick pre cast RCC rings, 150mm thick RCC slab on top, providing borewell of 10m
depth inside the well etc . Complete.
TESTING OF WATER
Collection of water sample from the borewell and getting it tested from approved laboratory for
the potability. The report to be submitted to the HPCL site-in-charge
LETTERING/ PAINTING FOR"FLUERS"
SPECIFICATION FOR LETTERING WORK FOR TOILET BLOCK- "Fleurs"
BOX LETTER MADE OUT OF 2 MM THK S S MATERIAL WITH SIDE 25 MM THK BOX TYPE
LETTER WITH BACKSIDE SCREW BRAZING FOR FITTING ARRANGEMENT. INCLUSIVE
P.U. COATING ( BLACK)
LETTER "F" 60" HEIGHT.BOX LETTER MADE OUT OF 2 MM THK S S MATERIAL WITH
SIDE 25 MM THK BOX TYPE LETTER WITH BACKSIDE SCREW BRAZING FOR FITTING
ARRANGEMENT. INCLUSIVE P.U. COATING ( BLACK)
LETTER "L" 36" HEIGHT.BOX LETTER MADE OUT OF 2 MM THK S S MATERIAL WITH SIDE
25 MM THK BOX TYPE LETTER WITH BACKSIDE SCREW BRAZING FOR FITTING
ARRANGEMENT. INCLUSIVE P.U. COATING ( BLACK)
LETTER "EURS" 48" HEIGHT.CLEAN TOILETS SIZE 4" HEIGHT X 1" THK 12 NOS. FLOWER
DESIGN WHITE/YELLOW P.U. COAT .
APPLYING 2 COAT TEXTURED
PAINT OF APPROVED MAKE AND SHADE ON TOILET BLOCK FASCIA WALL (APPROX
QTY- 12 SQM ) INCLUSIVE OF ALL MATERIAL AND LABOR, TOOLS ETC COMPLETE.
EA
2415
MR
135
MR
242
MR
275
EA
17659
EA
21000
EA
58
MR
121
EA
2415
EA
7729
MR
116
EA
6570
EA
7246
EA
10627
EA
1930
EA
43400