Page 1 of 2
GWWO, Inc./Architects | 800 Wyman Park Suite 300 Baltimore, MD 21211 US
Submittal Transmittal
Submittal ID:
062A-265100
Transmittal ID:
Date Sent:
00694
3/4/2013
Project:
Number:
Canaveral Cove
1124
To:
Scott Reekie
Skanska
677 Dave Nisbet Drive
Cape Canaveral, FL 32920
United States
(321) 783-0094 (Phone)
(866) 580-7875 (Fax)
From:
Bill Melluish
GWWO, Inc./Architects
800 Wyman Park
Suite 300
Baltimore, MD 21211
US
(410) 332-1009 x5044 (Phone)
(410) 332-0038 (Fax)
Subject:
Interior Lighting: PD
Via:
Spec Section:
Purpose:
Sharepoint
265100
Action Varies By Item
Remarks:
See "Contents" below and attached submittal sheets for review
action/comments/exceptions/resubmittal requirements on individual
items.
In addition to Engineer's comments included herein, note the
following:
z Luminaire Type K
{ As noted in Architect's review comments to package 062265100, approval subject to table-top evaluation; either
resubmit with specified fixture or provide product sample
for review.
z Luminaire Type S
{ As noted in Architect's review comments to package 062265100, approval subject to table-top evaluation; either
resubmit with specified fixture or provide product sample
for review.
z Luminaire Type T1
{ Color selection - white.
z Luminaire Type TA
{ Color selection - white.
z Luminaire Type TB
{ Color selection - white.
CC:
about:blank
Dave Perley(Canaveral Port Authority)
Christy Hartnett(Canaveral Port Authority)
3/4/2013
Page 2 of 2
John Gregg(GWWO, Inc./Architects)
Contents
Quantity:
1
Dated:
--
Number:
062A.01
Description:
Interior Lighting: PD
Action:
Action Varies By Item
Remarks:
See submittal comment review sheets and "Remarks" field above for action on individual items.
about:blank
3/4/2013
SUBMITTAL COMMENTS
Date: March 1, 2013
Project Title: Port Canaveral Welcome Center
Client Project No.: 1124
Henry Adams Project No.: 11-C004
Submittal Number:
062A-265100
Re: Interior Lighting - Product Data
Reviewed by: Josh Winemiller / Jeanne Tebera
265100 - Interior Lighting
Status: See below for comments.
General Comments:
G1. Comments for luminaires included under submittal 062A-265100 are indicated in bold
font below.
G2. Luminaires from submittal 062-265100 that were marked "No Exception Taken" are
included below and appear in light blue font.
G3. Comments have been repeated below in red font for luminaires included under submittal
062-265100 that were marked "Revise and Resubmit."
G4. Provide ballast and driver product data sheets for all luminaires per specification section
265100-1.3.A.3.
G5. Provide lamp data sheets for luminaires requiring separate lamping per specification section
265100-1.3.A.5.
Comments:
1. Luminaire Types A1/A2/A3/AW/TH/THW
a. Rejected - Provide specified luminaires.
b. Based on table-top evaluation of products, the substitute product is not equal to
the specified product.
• Specified luminaires have 4-5/16-inch diameter aperture . Substitute
luminaires have 4-1/2-inch diameter aperture.
• LED's are not visible on specified luminaires regardless of whether the
fixture is on or off. LED's in substitute luminaires consist of a cluster of
HENRY ADAMS, LLC | 600 Baltimore Avenue, Fourth Floor | Baltimore, MD 21204
(office) 410.296.6500 |(fax) 410.296.6501 | www.HENRYADAMS.com
March 1, 2013
SUBMITTAL COMMENTS
062A-265100
Port Canaveral Welcome Center
Page 2 of 4
•
yellow LED's in the center of the fixture. When the fixture is off, the
yellow LED's are visible in the center of the lens. This gives the lens an
aged, dirty appearance. See Photos 1a and 1b.
Specified luminaires have a self-flanged metal reflector (integral metal
trim ring). Substitute luminaires have a separate white plastic trim ring
that serves as the flange. See Photo 1c.
Photo 1a: Luminaire Types
A1/A2/A3/AW/TH/THW proposed substitute
Cooper Lighting
Photo 1b: Luminaire Types
A1/A2/A3/AW/TH/THW specified luminaire Gotham Lighting
Photo 1c: Cooper Lighting reflector
with white plastic trim ring
HENRY ADAMS, LLC | 600 Baltimore Avenue, Fourth Floor | Baltimore, MD 21204
(office) 410.296.6500 |(fax) 410.296.6501 | www.HENRYADAMS.com
March 1, 2013
SUBMITTAL COMMENTS
062A-265100
Port Canaveral Welcome Center
Page 3 of 4
2. Luminaire Type B
a. Rejected - Provide specified luminaire.
3. Luminaire Type C
a. No Exceptions Taken.
4. Luminaire Type D
a. Rejected - Provide specified luminaire.
i. Specified luminaire has an outside diameter of 9-1/4" and a depth of 91/16". Substitute luminaire has an outside diameter of 10.19" and a depth
of 10.1".
5. Luminaire Type E
a. Rejected - Provide specified luminaire.
6. Luminaire Type E1
a. No Exceptions Taken.
7. Luminaire Type F
a. Make Corrections Noted
i. Provide Light Level 1, 2100 lumens, 33 watt package.
8. Luminaire Type G2
a. No Exceptions Taken.
9. Luminaire Type G4
a. No Exceptions Taken.
10. Luminaire Type GS
a. Make Corrections Noted
i. Provide STS mounting - Stack Mount Single
11. Luminaire Type H
a. No Exceptions Taken.
12. Luminaire Type J
a. No Exceptions Taken.
13. Luminaire Type K
a. Subject to approval by architect.
HENRY ADAMS, LLC | 600 Baltimore Avenue, Fourth Floor | Baltimore, MD 21204
(office) 410.296.6500 |(fax) 410.296.6501 | www.HENRYADAMS.com
March 1, 2013
SUBMITTAL COMMENTS
062A-265100
Port Canaveral Welcome Center
Page 4 of 4
14. Luminaire Type L
a. No Exceptions Taken.
15. Luminaire Type LR1/LR2
a. Rejected based on performance. Substitute luminaires do not meet performance
features of specified luminaire. Photometric report for LR2 indicates luminaire
requires 208 watts. Specified luminaire requires 50W.
b. Provide specified luminaires.
16. Luminaire Type M
a. No Exceptions Taken.
17. Luminaire Type P
a. No Exceptions Taken.
18. Luminaire Type R
a. No Exceptions Taken.
19. Luminaire Type S
a. Subject to approval by architect.
20. Luminaire Track T1
a. Confirm finish color with architect.
21. Luminaire Type TA
a. Confirm finish color with architect.
22. Luminaire Type TB
a. Confirm finish color with architect.
23. Luminaire Type UC/UCD
a. Rejected - Provide specified luminaire.
24. Luminaire Type V
a. No Exceptions Taken.
25. Luminaire Type Y
a. No Exceptions Taken.
NO EXCEPTIONS TAKEN
REJECTED
MAKE CORRECTIONS NOTED
REVISE AND RESUBMIT
Checking only for general conformance with design
concept of the project and general compliance with the
information given in the contract documents. Any action
shown is subject to the requirements of the plans and
specifications. Contractor is responsible for: dimensions
which shall be confirmed and correlated at the job site;
fabrication processes and techniques of construction;
coordination of work with that of other trades and the
satisfactory performance of work.
HENRY ADAMS, LLC
Consulting Engineers
2013-03-01 By __________________________
JST/JLW
Date___________________
HENRY ADAMS, LLC | 600 Baltimore Avenue, Fourth Floor | Baltimore, MD 21204
(office) 410.296.6500 |(fax) 410.296.6501 | www.HENRYADAMS.com
SUBMITTAL TRANSMITTAL
Reference No: 0294
To: Bill Melluish
Date: 2/8/2013
GWWO, Inc./Architects
800 Wyman Park Drive, Suite 300
Project No.: 2312201
Project: Port Canaveral Welcome Center Building
Baltimore, MD 21211
P:410.332.1009
F: 410.332.0038
Submittal Package No: 0167 - - 0
We are sending you via: SharePoint
Interior Lighting - Product Data
Qty
1
Register/Rev
265100-00001
1
Spec/Sub Spec
265100
Type
Description
Product Data
Sheets
Interior Lighting - Product Data
Item Action
REVIEWED, NO EXCEPTIONS
X
REVIEWED, EXCEPTIONS NOTED
REVISE & RESUBMIT
REVIEWED, NO EXCEPTIONS
REVIEWED, EXCEPTIONS NOTED
REVISE & RESUBMIT
Subcontractor has determined and verified materials,
field measurements, and field construction criteria
related thereto, or will do so, and has checked and
coordinated information contained in this submittal with
the requirements of the Work and with the Contract
Documents. Checking is only for conformity to the
design concept of the project and compliance with the
information given in the contract documents.
Subcontractor is responsible for dimensions to be
confirmed and correlated at the job site, for information
that pertains solely to the fabrication process or the
techniques of construction and for coordination of the
work of all trades.
Project # _______________________________
Submittal # _____________________________
By: ____________________________________
Date: __________________________________
Subcontractor has determined and verified materials,
field measurements, and field construction criteria
related thereto, or will do so, and has checked and
coordinated information contained in this submittal with
the requirements of the Work and with the Contract
Documents. Checking is only for conformity to the
design concept of the project and compliance with the
information given in the contract documents.
Subcontractor is responsible for dimensions to be
confirmed and correlated at the job site, for information
that pertains solely to the fabrication process or the
techniques of construction and for coordination of the
work of all trades.
Project # _______________________________
2312201
Remarks
Submittal # _____________________________
265100-00001 R1
By: ____________________________________
SR
Date: __________________________________
2/8/2013
SEE ENGINEER'S "SUBMITTAL COMMENT"
SHEET AND GWWO SUBMITTAL TRANSMITTAL
FOR ACTION ON INDIVIDUAL ITEMS.
Additional Copies To:
-
Skanska USA Building Inc.
From: Scott Reekie
2/8/13 11:27 am
Page 1 of 1
Version 2
111 N. Magnolia Ave.
Suite 1150
Orlando, FL 32801
Tel: 407-839-2925
Professional • Passionate • Proficient
Port Canaveral
Interior Fixture-(Re-submittals)
Architect:GWWO
Engineer: Henry Adams
Contractor: Gerelco Electric
Lighting Dynamics Inc.
7835 West Commercial Blvd
Tamarac, FL, 33351
O:954-944-0286
C:772-285-7169
RHUFF@LIGHTINGDYNAMICS.COM
Date: Feb 4, 2013
Page 1/1
Transmittal
Project
Port Canaveral-Welcome Center-6006-REV
121812DS
Location PORT CANAVERAL FL
Contact:
Lighting Dynamics, Inc.
7835 West Commercial Blvd.
Tamarac FL 33351
Phone: (954) 944-0286
From: Debra Snow
ATTACHED WE ARE SENDING YOU 1 COPIES OF THE FOLLOWING ITEMS:
Drawings
Specifications
Other:
X Prints
Information
Plans
X Submittals
THESE ARE TRANSMITTED FOR:
Prior Approval
Approval
X Approval as Submitted
Approval as Noted
X
Type
FF00009
MFG
B
B
B
GS
L
LR1
LR1(FEET)
MISC4
MISC4
Corelite
MISC4
MISC4
MISC4
Boca Flasher
LR2
LR2(FEET)
MISC4
Boca Flasher
LR1/LR2
M
R
TA/TB
TA
UC
UC/UCD
UC/UCD
Resubmittal for Approval
Corrections
Your Use
Review and Comment
LDI - LIGHTING DYNAMICS, INC
Neo-Ray
LDI - LIGHTING DYNAMICS, INC
Record
Bids due on:
Other:
Part
INTERIOR
2VTL2-36L-ADP-D36-LP840-NX
SUBSTITUTION REQUEST
R3-WL-2L40-1D-UNV-22-T1
LIN-28-T5-STM-NB-T5-4'-1-W
FMG-NS-1T5-120-S-WH-4'
SUBSTITUTION FORM
HPCCS-TRGB-10X45-120-A-IP65-F-D(4) RUNS@24 FT EACH
SUBSTITUTION FORM
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
STICK DMX CONTROLLER
S22DR-L-L40-ETG-2-U-ED-S92HT
LEUCOS USA #106004-WALL SCONCE
SUBSTITUTION FORM
L805-MED-NF830MB/L1973-MB
RAZ24
SUBSTITUTION FORM
HU1024D830P/HU107P/HU106P
MISC4
Cooper Lighting
MISC4
MISC4
Cooper Lighting
Item Note: LENGTHS/FINISH & ACCESSORIES PER PLANS
Visit us on the web at www.lightingdynamics.com!
Page 1/1
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
INTERIOR
Type:
Notes:
LDI12-6006
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
2VTL2-36L-ADP-D36-LP840-NX
Type:
B
Notes:
LDI12-6006
Catalog
Number
Notes
FEATURES & SPECIFICATIONS
INTENDED USE — The VT Volumetric Troffer combines the aesthetics and high performance with intelligent
LED engines for applications - offices, schools, retail locations and hospitals. High-efficacy light engine
delivers long life and excellent color, ensuring a superior quality lighting installation that is highly efficient
and sustainable. Featured nLight controls system provides design flexibility and ease of installation and
optimum energy savings.
Type
CONSTRUCTION — Rugged, one-piece cold-rolled steel coated polyester, painted after fabrication with
embossed facets. Impact-modified, single clear acrylic diffuser provides excellent shielding and wide
distribution. End plates include integral T-bar clips. Fixture may be mounted and wired in continuous rows.
Total fixture height is only 4-3/8".
Volumetric Troffer
OPTICS — Volumetric illumination is achieved by creating an optimal mix of light to walls, partitions, vertical
and horizontal work surfaces — rendering the interior space, objects and occupants in a more balanced,
complementary luminous environment. Linear faceted reflector cavity softens and distributes light into
the space while minimizing luminous contrast between the fixture and ceiling. Sloped end plates provide
a smooth, luminous transition between fixture and ceiling while enhancing the perception of fixture depth.
2VTLED
Advanced optical film provides superior LED concealment and even illumination across the diffuser.
2' x 2'
LED
ELECTRICAL — Long-life LEDs, coupled with high-efficiency drivers, provide superior quantity and quality
of illumination for extended service life. VTLED is rated to deliver L80 performance for 50,000 hours.
Standard nLight™ embedded controls make each luminaire addressable - allowing it to digitally communicate
with other nLight enabled controls such as dimmers, switches, occupancy sensors and photocontrols. Simply
connect all the nLight enabled control devices and the VTLED luminaires using standard Cat-5 cabling. Unique
plug-and-play convenience as devices and luminaires automatically discover each other and self-commission.
Lumen Management: Unique lumen management system (option N80) provides onboard intelligence that
actively manages the LED light source so that constant lumen output is maintained over the system life,
preventing the energy waste created by the traditional practice of over-lighting.
INDUSTRY RECOGNITION/AWARDS
Bi-level dimming option allows system to be switched to 50% power for compliance with common energy
codes while maintaining fixture appearance.
LED AccuDrive ™ driver delivers full-range dimming from 0-10V control signal.
Driver disconnect provided where required to comply with US and Canadian codes.
2012 RECOGNIZED
PRODUCT
INSTALLATION — Unique grid interfacing arrangement provides mounting into standard 1" and 9/16"
tee bar or screw slot grids. 9/16" allows fixture trim to hang level with architectural ceiling tiles. Drywall
ceiling adaptors available. Suitable for damp location.
LISTINGS — CSA Certified to meet U.S. and Canadian standards.
2011 ARCHITECTURAL SSL PRODUCT
INNOVATION AWARD
Patents pending.
WARRANTY — 5-year limited warranty. Complete warranty terms located at
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
DLC certified test to LM80 standings.
Note: Specifications subject to change without notice.
ORDERING INFORMATION
2VTL2
ADP
Series
Air function
2VTL2 Volumetric
troffer 2X2
LED
(blank) Static
H
Heat
removal
Lumens
Diffuser
24L 2400
ADP Acrylic
lumens1
linear
prismatic
36L 3600
lumens1
Voltage
Wattage
(blank) MVOLT
347
3472
D24 24W3
D36 36W4
Color
temperature
WallPod stations
On/Off
On/Off & Raise/Lower
Graphic Touchscreen
Photocell controls
Continuous dimming
On/Off & Dimming
Model number
nPODM [color]
nPODM DX [color]
nPOD GFX
Model number
nCM ADC
nCM PC ADC
Occupancy sensors
Standard range 360°, ceiling (PIR / dual tech)
Extended range 360°, ceiling (PIR / dual tech)
Wide view (PIR / dual tech)
Cat-5 cable bundles (plenum rated)
10', CAT5 10FT
15', CAT5 15FT
Controls
LP835 82 CRI,
3500K
LP840 82 CRI,
4000K
LP850 82 CRI,
5000K
nLight™ Control Accessories:
Order as separate catalog number. Visit www.sensorswitch.com/nLight for complete listing of nLight controls.
LED
Example: 2VTL2 36L ADP D36 LP835 N100
Lead times will vary depending on options selected. Consult with your sales representative.
Model number
nCM 9 / nCM PDT 9
nCM 10 / nCM PDT 10
nWV 16 / nWV PDT 16
Model number
CAT5 10FT J1
CAT5 15FT J1
Options
NX
BLD
N80
N80EMG
Dimming, no nlight
Bi-level dimming
nlight with 80% lumen management.
nlight with 80% lumen management.
For use with generator supply EM
power.
N100
nlight without lumen management.
N100EMG nlight without lumen management.
For use with generator supply EM
power.
EL14L 1400
lumen
battery
pack
Accessories: Order as separate catalog number.
2VT2 F916
DGA22
Trim to adjust fixture mounting flush with 9/16" T-bar;
for 2x2 fixture
Drywall ceiling adaptor , unit installation
Notes
1 Approximate lumen output.
2 Consult factory for availability. Not available with EL14 battery pack or BLD controls.
3 For use with 2400 lumen system. Approximate input power (watts) +/-5%.
4 For use with 3600 lumen system. Approximate input power (watts) +/-5%.
2VTLED-2X2
Catalog Number:
2VTL2-36L-ADP-D36-LP840-NX
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
B
Notes:
LDI12-6006
2VTLED Volumetric Recessed Lighting 2'x2'
PHOTOMETRICS
2VTL2 24L ADP LP835, 2425 delivered lumens, test no. LTL20369, tested in accordance to IESNA LM-79
Coefficients of Utilization
pf
20%
pc
80%
70%
50%
pw 70%50%30% 50%30%10% 50%30%10%
0 119 119 119 116 116 116 111 111 111
1 109 104 100 102 98 94
97 94 91
2 99 91 84
89 82 77
85 80 75
3 90 80 71
78 70 64
75 69 63
4 83 71 62
69 61 55
67 60 54
5 76 63 54
62 54 47
60 53 47
6 70 57 48
56 48 42
54 47 41
7 65 52 43
51 43 37
50 42 37
8 61 47 39
47 39 33
45 38 33
9 57 44 35
43 35 30
42 35 30
10 53 40 32
40 32 27
39 32 27
180°
80°
100
200
300
60°
400
500
600
700
40°
800
900
0°
20°
0°
CP Summary
0° 90
0° 943 943
5° 931 941
15° 870 902
25° 755 829
35° 607 731
45° 461 616
55° 329 494
65° 210 373
75° 104 235
85° 23 53
90 1
1
Zonal Lumen Summary
Zone
Lumens % Lamp % Fixture
0° - 30°
703
29.0
29.0
0° - 40°
1123
46.3
46.3
0° - 60°
1906
78.6
78.6
0° - 90°
2425
100.0
100.0
90° - 180°
0
0.0
0.0
0° - 180°
2425
100.0
100.0
RCR
90°
Efficiency: 100.0%
90°
2VTL2 36L ADP L835, 3617 delivered lumens, test no. LTL20407, tested in accordance to IESNA LM-79
90°
80°
200
400
60°
600
800
1000
40°
1200
0°
20°
0°
CP Summary
0°
90
0° 1274 1274
5° 1262 1273
15° 1200 1230
25° 1081 1149
35° 918 1038
900
45° 726
743
55° 524
576
65° 332
366
75° 164
87
85° 37
2
2
90
Coefficients of Utilization
pf
20%
pc
80%
70%
50%
pw 70%50%30% 50%30%10% 50%30%10%
0 119 119 119 116 116 116 111 111 111
1 108 103 99 101 97 93
97 94 90
2 98 90 83
88 81 76
84 79 74
3 90 79 70
77 69 63
74 67 62
4 82 70 61
68 60 53
66 58 53
5 75 62 53
61 52 46
59 51 46
6 69 56 47
55 46 40
53 46 40
7 64 51 42
50 42 36
48 41 35
8 60 46 38
46 37 32
44 37 32
9 56 43 34
42 34 29
41 33 28
10 53 39 31
39 31 26
38 31 26
Zonal Lumen Summary
Zone
Lumens % Lamp % Fixture
0° - 30°
977
27.0
27.0
0° - 40°
1590
44.0
44.0
0° - 60°
2793
77.2
77.2
0° - 90°
3617
100.0
100.0
90° - 180°
0
0.0
0.0
0° - 180°
3617
100.0
100.0
RCR
180°
Efficiency: 100.0%
90°
Contact factory for 4000K.
Dimensions
Mounting Data
9/16
All dimensions are inches (centimeters) unless otherwise specified.
15/16
Specifications
4-3/8
(11.1)
Length: 24 (61.0)
Width: 24 (61.0)
9/16
with accessory 2VT2 F916
8-3/4
(22.2)
24
(61.0)
Depth: 4-3/8 (11.1)
SS
Constant Lumen Management
LED Energy Comparison to T5/T8
Enabled by the embedded nLight control, the VTLED actively tracks its run-time and manages its light source such that constant
lumen output is maintained over the system life. Referred to as lumen management, this feature eliminates the energy waste
created by the traditional practice of over-lighting.
Without Lumen Management
With Lumen Management
Energy is wasted and light level is inconsistent.
Energy is saved and light level remains consistent.
100%
36W
100%
VTLED N100 (3600L)
VTLED N80 (3600L)
2-lamp T8
2-lamp T5
36W
POWER
INPUT
POWER INPUT
LIGHT
OUTPUT
LIGHT OUTPUT
Saved Energy
POWER INPUT
LIGHT OUTPUT
POWER INPUT
1
LIGHT OUTPUT
80%
30
40
29W
50
80%
0
10
20
THOUSAND OPERATING HOURS
30
40
Lamp
type
LED
LED
F32T8U
F24T5HO
Ballast
factor
1.0
1.0
0.88
1.0
Input
watts
36
29
58
54
Watts saved
by using LED
22
18
Notes
Wasted Energy
0
10
20
THOUSAND OPERATING HOURS
System
29W
50
With nlight 80% lumen management input watts start at 29 and gradually increasing
to 36 at 50,000 hrs when using 36L system.
2VTLED-2X2
LED: One Lithonia Way Conyers, GA 30012
Phone: 800-858-7763
Fax: 770-929-8789
www.lithonia.com
© 2011-2012 Acuity Brands Lighting, Inc. All rights reserved.
Rev. 09/10/12
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION REQUEST
Type:
B
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase)
Project: Port Canaveral Welcome Center
Substitution Request Number:
From:
To:
Lighting
Incorporated
Date:
GWWO Architects/ Henry Adams Cons. Engineers
11/30/12
A/E: Project Number:
Re:
Dynamics
Contract For:
Lighting Dynamics Inc.
1124
Port Canaveral Welcome Center
Specification Title: Substitution Procedures
Description: Substitutions
Section: 012500
Article/Paragraph:
Page: 18
1.1-1.4
Proposed/Substitution:
Manufacturer:
Corelite (Cooper Industries)
Address:
Available upon request
Model #: R3-WL-L40-1D-UNV-22-T1
2L40
Installer:
History:
Gerelco Electrical Contractors
New product
Address: 560 NW Enterprise Drive, Port Saint Lucie,FL,34986 Phone: 772-340-7474
1-4 years old
5-10 years old
Differences between proposed substitution and specified product:
More than 10 years old
Product is comparable in performance, design & aesthetics
Point-by-point comparative data attached — REQUIRED BY A/E
Reason for not providing specified item: We don’t represent the specified manufacturer, we are providing a comparable product
In design, performance & aesthetics
Similar Installation: This product has been used on numerous projects in size and scope comparable to this project. Additional information is
available upon further request from Architect & Engineer.
Project:
Available upon request
Architect: Available upon request
Address:
Owner:
N/A
Date Installed: N/A
Proposed substitution affects other parts of Work:
No
Yes; explain
Savings to Owner for accepting substitution: Alternate Equal
Proposed substitution changes Contract Time:
Supporting Data Attached:
Drawings
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
No
Yes [Add]
Product Data
Samples
Page
of
($ 0
).
[Deduct]
days.
Tests
Reports
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION REQUEST
Type:
B
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase
— Continued)
The Undersigned certifies:
• Proposed substitution has been fully investigated and determined to be equal or superior in all respects to specified product.
• Same warranty will be furnished for proposed substitution as for specified product.
• Same maintenance service and source of replacement parts, as applicable, is available.
• Proposed substitution will have no adverse effect on other trades and will not affect or delay progress schedule.
• Cost data as stated above is complete. Claims for additional costs related to accepted substitution which may subsequently become
apparent are to be waived.
• Proposed substitution does not affect dimensions and functional clearances.
• Payment will be made for changes to building design, including A/E design, detailing, and construction costs caused by the substitution.
• Coordination, installation, and changes in the Work as necessary for accepted substitution will be complete in all respects.
Submitted by: Lighting Dynamics Inc.
Signed by:
Ryan Huff
Firm:
Lighting Dynamics Inc.
Address:
7835 W Commercial Blvd, Tamarac, FL, 33351
Telephone:
954-944-0286
Attachments:
A/E’s REVIEW AND RECOMMENDATION
Approve Substitution - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Approve Substitution as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Reject Substitution - Use specified materials.
Substitution Request received too late - Use specified materials.
Signed by:
Date:
OWNER'S REVIEW AND ACTION
Substitution approved - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare Change
Order.
Substitution approved as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare
Change Order.
Substitution rejected - Use specified materials.
Signed by:
Additional Comments:
Other:
Date:
Contractor
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
Subcontractor
Page
Supplier
of
Manufacturer
A/E
Form Version: November 2010
CSI Form 13.1A
Catalog Number:
R3-WL-2L40-1D-UNV-22-T1
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
B
Notes:
LDI12-6006
CORELITE
DESCRIPTION
The Corelite R3 LED combines the internally developed Linear LED platform
from Cooper Lighting with the high sense of style and superior brightness
management that characterizes the CoreLite Class R family. The proprietary
LED platform delivers a soft, diffuse volume of pure white light that carries
the general character of a fluorescent source while simultaneously
eliminating unsightly socket shadows and the hassle of luminaire
maintenance. A guaranteed system life of 50,000 hrs combined with
exceptional efficacy make the R3 LED the ultimate solution to satisfy the
most stringent energy requirements with an ultra-light carbon footprint.
Type
Catalog #
Project
Date
Comments
Prepared by
SPECIFICATION FEATURES
A ... Construction
Low profile housing constructed of
die formed 20 gauge cold rolled
steel with integral 20 gauge gear
tray.
B ... Reflector
Precision tooled, high reflectance
sheet metal which allows for easy
access to driver compartment from
below ceiling plenum.
C ... Shielding
High light transmission frosted
prismatic acrylic lens with UV
inhibitors minimizes lamp image
and ensures efficient light
distribution. Lenses secured to
housing via injection molded
inserts for easy lamp access.
D ... Electrical
Fixture equipped with proprietary
Cooper LED modules available in
3000, 3500 or 4000k with a CRI plus
or minus 85. Removable module
features aluminum extrusion
providing exceptional thermal
management. Modules are driven
using universal voltage switch
mode LED drivers. Fixture and
modules certified to UL and CUL
standards. A 0 to 10V dimming
control is available (standard).
Mounting
Standard flange design works with
most lay in ceiling types. Integral
pryout tabs secure luminaire to
ceiling grid from above. Fixture
offers tie in locations for tie wire
on all corners, consult local code
for appropriate tie wire
recommendations.
NOTE: Concealed Ceiling
Class R may be installed into
inaccessible ceilings (sheet rock,
wood panel, etc.). This is achieved
with the Metalux DFW series
drywall frame-in kit, ordered
separately from Metalux. Specify
CC for the Corelite Ceiling Type.
Specify the following part numbers
separately, from Metalux: For 2x2,
order Metalux part DF-22W-U.
E ... Finish
Fixture housings are high
reflectance white using
electrostatically applied polyester
powder coat paint.
Alternate Dimensions - 2x2
T5
T5HO
CFL
T8
LED
A
B
C
23 3/4" [603MM]
24 3/8" [619MM]
D
CLASS R3
Linear Prismatic
Lens
E
LED
2'x2' Recessed
3-3/4”
[95mm]
3-3/4" Depth
23-3/4” [603mm]
24” [610mm]
ORDERING INFORMATION
Sample Number: R3-WL-1L30-1C-UNV-22-T1
Series
R3=Class R3
Shielding
L=Linear Prismatic Lens
Reflector
W=White
Light Level
1=Light Level 1
2=Light Level 2
Notes: 1
Color Temperature
L30=LED 3000K
Wiring 1
C=Standard Circuit
Voltage 1
120=120V
L35=LED 3500K
L40=LED 4000K
D=Dimming
E=Emergency
277=277V
347=347V
T=Nightlight
Y=Daylight
UNV=Universal
(120V-277V)
Number of Circuits
1=1 Circuit
Ceiling Type
T1=1" Grid, Slot-Grid,
9/16" Tegular
T9=9/16" Grid
CC=Concealed Ceiling
Size
22=2' x 2'
Options 1
AR=Air Return
CP=Chicago Plenum
NY=New York City
Construction
W6=6' Whip Flex
W12=12' Whip Flex
Not all options available. Please consult your Cooper Lighting Representative for
availability. Specifications and dimensions subject to change without notice.
DesignLights™ Consortium Qualified. Refer to www.designlights.org Qualified Products List under Family Models for details.
Specifications and Dimensions subject to change without notice.
Consult your representative for additional options and finishes.
ADE110534
12/07/2012 2:27:18 PM
Catalog Number:
R3-WL-2L40-1D-UNV-22-T1
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
B
Notes:
LDI12-6006
Corelite
PHOTOMETRICS
Candela
Coefficients of Utilization
90°
Effective floor cavity reflectance
75°
60°
400
45°
800
1200
0°
15°
30°
R3-WL-2L35-2x2
3188 Lumens
37.3 Watts
85.5 LPW
LED ALM 2.0
80%
rc
rw
20%
70%
70 50 30 10
70 50 30 10
30%
10%
50 30 10
50 30 10
0%
50 30 10
0
RCR
0
1
2
3
4
5
6
7
8
9
10
119
108
98
89
81
75
69
64
60
56
52
119
103
89
78
69
62
55
50
46
42
39
119
98
82
70
60
52
46
41
37
34
31
119
94
76
63
53
46
40
35
31
28
25
116
105
95
87
79
73
67
62
58
54
51
116
101
87
77
68
61
55
49
45
41
38
116
97
81
69
59
52
46
41
37
33
31
116
93
75
62
53
45
40
35
31
28
25
111
96
84
74
65
58
53
48
44
40
37
Zonal Lumen Summary
Test Report: #P22318
50%
Zone
0-30
0-40
0-60
0-90
40-90
60-90
90-180
0-180
Lumens
% Lamp
841
1371
2431
3188
1816
757
0
3188
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
111
93
78
67
58
51
45
40
36
33
30
111
90
74
61
52
45
39
35
31
28
25
106
93
81
71
63
56
51
46
43
39
36
106
90
76
65
56
50
44
40
36
33
30
106
87
72
60
51
44
39
34
31
28
25
102
89
77
68
61
54
49
45
41
38
35
102
87
74
63
55
49
43
39
35
32
29
102
85
70
59
51
44
39
34
31
28
25
100
82
68
57
48
42
36
32
29
26
23
Luminance Data
% Fixture
Angle
in Deg
26.4
43
76.3
100
57
23.7
0
100
0-Deg
cd/sm
45
55
65
75
85
2626
2343
2061
1782
1578
45-Deg
cd/sm
90-Deg
cd/sm
2897
2852
2800
2823
2728
3193
3287
3451
3686
3419
Coefficients of Utilization
Effective floor cavity reflectance
300
rc
rw
60°
RCR
45°
600
900
0°
15°
30°
R3-WL-1L35-2x2
2496 Lumens
28.1 Watts
88.8 LPW
LED ALM 2.0
Test Report: #P22357
0
1
2
3
4
5
6
7
8
9
10
80%
119
108
98
89
81
75
69
64
60
56
52
119
103
89
78
69
62
55
50
46
42
39
119
98
82
70
60
52
46
41
37
34
31
20%
70%
70 50 30 10
70 50 30 10
119
94
76
63
53
46
40
35
31
28
25
116
105
95
87
79
73
67
62
58
54
51
116
101
87
77
68
61
55
49
45
41
38
116
97
81
69
59
52
46
41
37
34
31
Zonal Lumen Summary
Zone
Lumens
0-30
0-40
0-60
0-90
40-90
60-90
90-180
0-180
659
1074
1904
2496
1421
592
0
2496
0-Deg
23-Deg
45-Deg
68-Deg
90-Deg
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
1088
1086
1069
1040
999
943
878
807
732
648
557
469
384
304
229
161
100
48
0
1088
1084
1068
1041
1003
949
887
818
743
664
580
499
414
336
261
189
122
60
0
1088
1083
1069
1044
1008
963
907
848
783
715
646
571
492
413
334
255
176
83
0
1088
1082
1068
1049
1017
975
928
877
825
769
705
635
561
483
400
313
210
99
0
1088
1082
1068
1052
1020
981
937
889
842
788
726
658
587
509
425
333
209
104
0
Candela
90°
75°
Angle
116
93
75
62
53
45
40
35
31
28
25
50%
30%
50 30 10
50 30 10
111
96
84
74
65
58
53
48
44
40
37
111
93
78
67
58
51
45
40
36
33
30
111
90
74
61
52
45
39
35
31
28
25
106
93
81
71
63
56
51
46
43
39
36
106
90
76
65
56
50
44
40
36
33
30
10%
106
87
72
60
51
44
39
34
31
28
25
0%
50 30 10
102
89
77
68
61
55
49
45
41
38
35
102
87
74
63
55
49
43
39
35
32
29
102
85
70
59
51
44
39
34
31
28
25
Luminance Data
% Lamp
% Fixture
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
N.A.
26.4
43
76.3
100
57
23.7
0
100
Angle
in Deg
45
55
65
75
85
0-Deg
cd/sm
2046
1833
1620
1384
1183
45-Deg
cd/sm
90-Deg
cd/sm
2269
2233
2190
2214
2137
2500
2572
2698
2878
2696
0
100
82
68
57
48
42
36
32
29
26
23
Angle
0-Deg
23-Deg
45-Deg
68-Deg
90-Deg
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
853
850
838
815
783
740
689
632
570
505
436
367
301
239
178
125
79
36
0
853
850
837
815
785
743
694
641
582
520
455
390
325
263
203
148
96
47
0
853
849
838
818
790
754
710
664
613
560
506
447
385
323
261
200
137
65
0
853
848
837
821
796
764
727
687
647
603
553
498
439
379
313
244
164
77
0
853
848
837
824
799
768
734
698
659
617
568
515
458
398
331
260
163
82
0
Specifications and Dimensions subject to change without notice.
Corelite • 18001 E. Colfax Ave. • Aurora, CO 80011 • 303.393.1522 • FAX 303.393.1477
ADE110534
12/07/2012 2:27:18 PM
Catalog Number:
LIN-28-T5-STM-NB-T5-4'-1-W
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
GS
Notes:
LDI12-6006
INTERIOR
ARCHITECTURAL
FLUORESCENT
LUMINAIRES
STACK MOUNT, WALL MOUNT,
PENDANT AND AIRCRAFT CABLE MOUNT
LINEA
T5/T5HO FLUORESCENT
SINGLE AND MULTIPLE LUMINAIRE RUN
SYMMETRIC
BEAM ANGLES
60°
100°
ORDERING
PRODUCT
FAMILY
WATTAGE
LIN
14, 21, 28
24, 39, 54
LIGHT
SOURCE
T5
T5HO
OPTICS
MOUNTING
LENGTH
VOLTAGE
2
3
4
6
8
12
1. 120V
FINISH
OPTIONS/ACCESSORIES
(12’ Maximum on all single mount)
X SPECIFIES ARM/CABLE LENGTH
60 Narrow
Beam (60°)
100 Wide
Beam
(100°)
STS Stack Mount Single
STM Stack Mount Multiple
WMS-X Wall Mount Single
WMM-X Wall Mount Multiple
X = Length 6” min, 18” max
2’
3’
4’
6’
8’
12’
PNS-X Pendant Mount Single
PNM-X Pendant Mount Multiple
X= Length 6” min.
ACS-X Aircraft Cable Single
ACM-X Aircraft Cable Multiple
X = Length 6”min, 10’ max
SPECIFICATIONS
Housing: The housing is manufactured from extruded aluminum with
tooled aluminum couplings and end caps ranging from 2 to 12 feet.
Mounting: Formed steel pipe attach to the fixture housing with a rotatable coupler, and have a welded interface with stack mount brackets
that provide for easy installation. Continuous runs allow for independent
adjustment.
Electrical: Integral, electronic, high power factor ballast. Available in
120V through 347V. Optional dimming ballasts and emergency battery
packs are available.
2. 277V
3. 347V
W Semi-Gloss White
BL Semi-Gloss Black
BR Semi-Gloss Bronze
N
Semi-Gloss Natural
S
Semi-Gloss Satin
G Semi-Gloss Graphite
SF
Specify Finish
(Contact factory)
CC
Custom Color
(Contact Factory)
DM
Dimming Ballast
(Contact factory)
EMP Emergency Battery Pack
(Contact factory)
Reflector: CAD designed, highly efficient reflector is constructed of
95% reflective, peened, anodized aluminum providing clean, even
distribution with no streaks or striations. Two distinct symmetrical
distributions are available; narrow beam (60°) and wide beam (100°)
Lens: An extruded linear prismatic acrylic snap-in tool-less lens is
provided. Lens are based on beam distribution.
Finish: Consult factory for additional choices of custom colors. All
painted surfaces are pretreated and TGIC powder coated to a minimum 3-mil thickness.
Labels: UL/CUL approved for damp locations.
Insight Lighting reserves the right to change specifications
ORDERING EXAMPLE: LIN/14/T5/100/STS/6/120/BR/DM
PRODUCT
FAMILY
WATTAGE
LIGHT
SOURCE
OPTICS
MOUNTING
FIXTURE LENGTH
VOLTS
FINISH
OPTIONS
TYPE:
JOB NAME:
Rio Rancho, NM 87144
TEL: 505 345-0888
www.insightlighting.com
APPROVED:
05/11
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
LIN-28-T5-STM-NB-T5-4'-1-W
Type:
GS
Notes:
LDI12-6006
INTERIOR
ARCHITECTURAL
FLUORESCENT
LUMINAIRES
LINEA
STACK MOUNTING (STS)
MOUNTING DIMENSIONS
103
8
Nominal Length
2'
4'
6'
'A'
25-5/8"
37-3/8"
49-1/4"
71-5/8"
'B'
22-3/8"
34-1/8"
46"
68-3/8"
3'
8'
12'
95-1/4" 141-1/4"
92"
138"
8'
12'
3
Ø24
1
62
148°
47
8
WALL MOUNTING (WMS)
MOUNTING DIMENSIONS
Ø23
4"
SPECIFY*
Nominal Length
2'
4'
6'
'A'
25-5/8"
37-3/8"
49-1/4"
71-5/8"
'B'
22-3/8"
34-1/8"
46"
68-3/8"
3'
'A'
47
8"
*MIN 6"
MAX 18"
148°
'B'
95-1/4" 141-1/4"
92"
138"
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
FMG-NS-1T5-120-S-WH-4'
Type:
L
Notes:
LDI12-6006
m in i- g r a ze r
™
features
High performance, T5 or T5HO Fluorescent
Wall Grazer.
Nautilus optic designed to highlight textured
walls and ceilings evenly from ceiling to floor.
Swing down lamp tray allows for easy lamp
accessibility.
Housing creates 6" architectural slot.
Great energy solution that replaces multiple
MR16 or PAR lamps commonly used for
grazing applications.
Housing designed for drywall or grid ceilings.
shielding options
dimensional data
open optic
baffle
april 2009
dimensional data
mounting surface must be
flush with textured wall
12.56"
319mm
height of mounting rail
will automatically set
height of outer shell
5.57"
142mm
suspended ceiling line
performance
1-lamp T5HO
37% Efficiency
3734 cd @ 5°
6.00"
152mm
sheet rock ceiling line
textured wall must be flush
with mounting surface
Visit focalpointlights.com for
complete photometric data.
406 | www.focalpointlights.com | 1.773.247.9494
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
FMG-NS-1T5-120-S-WH-4'
Type:
L
Notes:
LDI12-6006
fixture:
project:
ordering
mounting information
Grid
Drywall
FMG
luminaire series
Mini-Grazer
FMG
shielding
No Shielding, Open Optic
Baffle, White
NS
BB
lamping
One Lamp T5
One Lamp T5HO
Mount drywall under luminaire and support to
ceiling structure.
NOTE: Add drywall thickness to overall height
of luminaire.
typical run layout
Overall Length
“xx”
sliding sleeves
90 Degree
Inside Corner
Sliding Sleeve
12" Max
Sliding Sleeve
Sliding Sleeve
Overall
Length
Fractional Dimensions up to 12" are
taken up by the use of a sliding sleeve.
“xx”
Overall
Length
90 Degree
Outside Corner
Sliding
Sleeve
“xx”
Luminaires must be installed prior to ceiling.
Start run from corner with any standard luminaire.
Corner to corner runs end with a sliding sleeve.
1C
voltage
120 Volt
277 Volt
347 Volt
NOTE: Luminaire must be installed prior to ceiling.
1C
circuits
Single Circuit
120
277
347
ballast
Electronic Dimming Ballast* D
Electronic Program Start <10% THD S
factory options
Air Return
AR
Chicago Plenum
CP
Emergency Circuit* EC
Emergency Battery Pack* EM
HLR/GLR Fuse FU
Include 3000K Lamp
Include 3500K Lamp
Include 4100K Lamp
12" Sliding Sleeve
L830
L835
L841
SS
WH
finish
Matte White Housing
WH
luminaire length
Designate overall run length dimension
(light modules provided in 3' & 4' lengths)
4'
corner options
specifications
90–degree Inside Corner
90–degree Outside Corner
construction
20 Ga. steel housing.
20 Ga. internal bulkheads.
20 Ga. steel rough–in housings are provided to create wall to wall slot.
20 Ga. steel sliding sleeve.
Optional baffle (.650"H x .800" frequency) provides 50° cutoff to lamp and held
captive with torsion springs.
Luminaires are available in 3' and 4' lengths.
3' unit weight:
4' unit weight:
XX'
FMG-IC90
FMG-OC90
NOTE: Not intended for drywall surfaces
unless a Level 5 finish is specified.
24 lbs
26 lbs
optic
CNC roll-formed specular .016" thick aluminum.
electrical
Electronic ballasts are thermally protected and have a Class “P” rating.
Consult factory for dimming specifications and availability.
UL and cUL listed.
finish
Polyester powder coat applied over a 5-stage pre–treatment.
Focal Point LLC | 4141 S. Pulaski Rd, Chicago, IL 60632 | T: 773.247.9494 | F: 773.247.8484 | info@focalpointlights.com | www.focalpointlights.com.
Focal Point LLC reserves the right to change specifications for product improvement without notification.
Acoustical tile may rest on flange of luminaire.
1T5
1T5HO
* for more information see Reference section.
perimeter | 407
363
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000066-00
Type:
LR1
Notes:
LDI12-6006
Specifications
Due to continuous improvements and innovations, specifications may change without notice.
Item
Output
Electrical
Control
Specification
1 ft (305 mm)
4 ft (1.2 m)
Lumens*
384 (10° x 60° beam angle)
380 (30° x 60° beam angle)
1407 (10° x 60° beam angle)
1391 (30° x 60° beam angle)
Lumen Maintenance†
50,000 hours L70 @ 25° C 37,000 hours L70 @ 50° C
90,000 hours L50 @ 25° C 80,000 hours L50 @ 50° C
LED Channels
Red / Green / Blue
Input Voltage
100 – 240 VAC, auto-switching, 50 / 60 Hz
Power Consumption
12.5 W maximum at full
output, steady state
Interface
Data Enabler Pro (DMX or Ethernet)
Control System
Philips full range of controllers, including Light System
Manager, iPlayer 3, and ColorDial Pro, or third-party
controllers
(Height x Width x Depth)
2.1 x 12 x 1.5 in
(53 x 305 x 39 mm)
2.1 x 48 x 1.5 in
(53 x 1219 x 39 mm)
Weight
0.98 lbs (.45 kg)
4.37 lbs (1.98 kg)
Housing
Die-cast aluminium, white powder-coated finish.
Lens
Polycarbonate
Fixture Connections
Integral male / female connectors
Temperature Ranges
-4° – 122° F (-20° – 50° C) Operating
-4° – 122° F (-20° – 50° C) Startup
-40° – 176° F (-40° – 80° C) Storage
Humidity
0 – 95%, non-condensing
Fixture Run Lengths
To calculate fixture run lengths and total power consumption
for your specific installation, download the Configuration
Calculator from www.philipscolorkinetics.com/support/
install_tool/
Certification
UL / cUL, FCC Class B, CE, PSE, CCC, C-Tick, SAA
Environment
Dry / Damp Location, IP20
Physical
Certification
and Safety
180º
10º
50 W maximum at full output,
steady state
Dimensions
10º
10° x 60°
* Lumen measurement complies with IES LM-79-08 testing
procedures.
† L70 = 70% lumen maintenance (when light output drops
below 70% of initial output). L50 = 50% lumen maintenance (when light output drops below 50% of
initial output). Ambient luminaire temperatures specified. Lumen maintenance calculations are based
on lifetime prediction graphs supplied by LED source manufacturers. Calculations for white-light LED
fixtures are based on measurements that comply with IES LM-80-08 testing procedures. Refer to www.
philipscolorkinetics.com/support/appnotes/lm-80-08.pdf for more information.
10° x 60°
30° x 60°
180º
1.5 in
39 mm
12 in
(305 mm)
2.1 in
53 mm
9.1 in
(231 mm)
1.1 in
(28 mm)
9.5 in
(241 mm)
1.6 in
41 mm
48 in
1219 mm
2.1 in
53 mm
46.9 in
1192 mm
46.38 in
1178 mm
.63 in
16 mm
.47 in
12 mm
6
ColorFuse Powercore Product Guide
Ø .16 in
4 mm
0.63 in
(16 mm)
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000066-00
Type:
LR1
Notes:
LDI12-6006
Fixtures and Accessories
ColorFuse Powercore fixtures are part of a complete system which includes fixtures
and:
• One or more Data Enabler Pro devices.
• One Leader Cable to connect each Data Enabler Pro output to a series of fixtures,
or one Wiring Compartment with a sufficient length of 4-conductor copper wire.
Standard 12 AWG stranded wire is recommended.
Included in the box
ColorFuse Powercore fixture
Installation Instructions
• Any Philips controller, including Light System Manager, iPlayer 3, and ColorDial Pro, or
a third-party controller.
Item
ColorFuse Powercore
1 ft (305 mm)
ColorFuse Powercore
4 ft (1.2 m)
Optional mounting track ensures straight runs of fixtures.
Mounting Track, White
Leader Cable
with Terminator
Depending on the installation’s design,
you may need jumper cables to add space between fixtures.
Type
10° x 60°
30° x 60°
10° x 60°
30° x 60°
UL / cUL / CE
1 ft (305 mm)
CCC
123-000066-02
910503701993
123-000066-01
910503701784
CCC
123-000066-03
910503701994
UL / cUL / CE
123-000066-04
910503702589
CCC
123-000066-06
910503703167
UL / cUL / CE
123-000066-05
910503702590
CCC
123-000066-07
910503703168
120-000124-00
910503701787
UL / cUL
108-000050-00
910503701686
CE / CCC
108-000050-01
910503701687
UL / cUL
108-000049-01
910503701683
CE / CCC
108-000049-03
910503701685
UL / cUL
108-000049-00
910503701682
CE / CCC
108-000049-02
910503701684
UL / cUL
120-000077-02
910503701740
120-000058-00
910503700146
3/4 in / 1/2 in NPT
(U.S. trade size conduit)
106-000004-00
910503701210
PG21 / PG13
(metric size conduit)
106-000004-01
910503701211
Jumper Cable
5 ft (1.5 m)
Wiring Compartment with Terminator
Terminator, Quantity 10
Data Enabler Pro
Philips 12NC
910503701783
UL / cUL / CE
1 @ 4 ft (1219 mm)
10 ft (3.1 m)
Item Number
123-000066-00
Use Item Number when ordering in North America.
Wiring Compartment dimensions
1.65 in
(42 mm)
.875 in
(22.2 mm)
1.65 in
(42 mm)
1.2 in
(29 mm)
4.3 in
(110 mm)
ColorFuse Powercore Product Guide 7
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000066-00
Type:
LR1
Notes:
LDI12-6006
Installation
ColorFuse Powercore offers high-intensity, full-color surface grazing and wall washing
with Powercore technology. Powercore, which integrates LED power and data
management within the fixture, eases installation by eliminating the need for external
power supplies.
Owner / User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to install,
maintain, and operate ColorFuse Powercore fixtures in such a manner as to comply
with all applicable codes, state and local laws, ordinances, and regulations. Consult with
the appropriate electrical inspector to ensure compliance.
E Refer to the ColorFuse Powercore
Installation Instructions for specific warning
and caution statements.
Prepare for the Installation
Determine the appropriate location of each Data Enabler Pro in relation to the fixtures,
and of the fixtures in relation to each other. The Data Enabler Pro and first fixture must
be separated by no more than the 10 ft (3.1 m) length of the Leader Cable.
ColorFuse Powercore fixtures are installed in series. The in-line connectors allow
end-to-end fixture connections for the best visual effects. Joined directly together,
the connectors on the 1 ft (305 mm) fixtures allow for spacing of .4 in (10 mm) to .9
in (23 mm) without a jumper cable, while the connectors on the 4 ft (1.2 m) fixtures
allow for spacing of .9 in (23mm) to 2 in (51 mm) without a jumper cable. When you
need to separate fixtures by more than these minimums, use the 1 ft (305 mm) or 5
ft (1.5 m) jumper cables.
The maximum number of fixtures each Data Enabler Pro can support depends on specific
configuration details such as fixture length, fixture spacing, circuit size, line voltage, and
Leader Cable length. For help calculating the number of fixtures your specific installation
can support, download the Configuration Calculator from www.philipscolorkinetics.
com/support/install_tool/, or consult Application Engineering Services at support@
colorkinetics.com.
E Refer to the Data Enabler Pro
Installation Instructions or Product Guide for
guidelines on configuring and positioning the
Data Enabler Pro in relation to the controller.
Distance between fixtures
joined end-to-end
.4 in minimum
(10 mm minimum)
.9 in maximum
(23 mm maximum)
1 ft (305 mm) fixtures
.9 in minimum
(23 mm minimum)
2 in maximum
(51 mm maximum)
In addition to maximum fixture run lengths determined by the electrical configuration,
each Data Enabler Pro imposes maximum run lengths based on data integrity. To ensure
data integrity, maximum individual run lengths should not exceed 175 ft (53.3 m), and
the total cable length per Data Enabler Pro should not exceed 400 ft (122Data
m).
Enabler Pro
Fixtures
4 ft (1.2 m) fixtures
Data
Enabler Pro
Easy turns
Fixtures
End-to-end locking power connectors can make
turns of up to 180º without jumper cables.
Data Integrity — maximum individual length 175 ft (53.3 m)
Data
Enabler Pro
Fixtures
Fixtures
8
Data
Enabler Pro
Data Integrity — total length 400 ft (122 m)
ColorFuse Powercore Product Guide
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000066-00
Type:
LR1
Notes:
LDI12-6006
3. Position the next fixture in the series, matching the male connector end to the
female connector of the previously mounted fixture. Attach the fixture to the
surface or snap it into the track.
4. Continue mounting the fixtures, making power / data connections as you go, until
all lights in the series are mounted.
5. Insert the provided terminator into the last fixture in the series.
CLICK!
Make Power Connections
1. If using a Leader Cable, connect the Leader Cable to the first fixture in the series.
Run the Leader Cable to the Data Enabler Pro.
Leader Cable connector dimensions
.375 in
(10 mm)
.53 in
(13.5 mm)
.375 in
(10 mm)
.53 in
(13.5 mm)
.94 in
(24 mm)
.94 in
(24 mm)
2.2 in
(55.6 mm)
Leader Cable
2.2 in
(55.6 mm)
Data Enabler Pro
ColorFuse Powercore Product Guide 11
Catalog Number:
SUBSTITUTION FORM
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
LR1
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase)
Project: Port Canaveral Welcome Center
Substitution Request Number:
From:
To:
Lighting
Incorporated
Date:
GWWO Architects/ Henry Adams Cons. Engineers
11/30/12
A/E: Project Number:
Re:
Dynamics
Contract For:
Lighting Dynamics Inc.
1124
Port Canaveral Welcome Center
Specification Title: Substitution Procedures
Description: Substitutions
Section: 012500
Article/Paragraph:
Page: 18
1.1-1.4
Proposed/Substitution:
Manufacturer:
Model #:
Installer:
History:
BOCA FLASHER
Address:
Available upon request
HPCCS-TRGB-10X45-120-A-IP65-F-D
Gerelco Electrical Contractors
New product
Address: 560 NW Enterprise Drive, Port Saint Lucie,FL,34986 Phone: 772-340-7474
1-4 years old
5-10 years old
Differences between proposed substitution and specified product:
More than 10 years old
Product is comparable in performance, design & aesthetics
Point-by-point comparative data attached — REQUIRED BY A/E
Reason for not providing specified item: We don’t represent the specified manufacturer, we are providing a comparable product
In design, performance & aesthetics
Similar Installation: This product has been used on numerous projects in size and scope comparable to this project. Additional information is
available upon further request from Architect & Engineer.
Project:
Available upon request
Architect: Available upon request
Address:
Owner:
N/A
Date Installed: N/A
Proposed substitution affects other parts of Work:
No
Yes; explain
Savings to Owner for accepting substitution: Alternate Equal
Proposed substitution changes Contract Time:
Supporting Data Attached:
Drawings
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
No
Yes [Add]
Product Data
Samples
Page
of
($ 0
).
[Deduct]
days.
Tests
Reports
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
LR1
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase
— Continued)
The Undersigned certifies:
• Proposed substitution has been fully investigated and determined to be equal or superior in all respects to specified product.
• Same warranty will be furnished for proposed substitution as for specified product.
• Same maintenance service and source of replacement parts, as applicable, is available.
• Proposed substitution will have no adverse effect on other trades and will not affect or delay progress schedule.
• Cost data as stated above is complete. Claims for additional costs related to accepted substitution which may subsequently become
apparent are to be waived.
• Proposed substitution does not affect dimensions and functional clearances.
• Payment will be made for changes to building design, including A/E design, detailing, and construction costs caused by the substitution.
• Coordination, installation, and changes in the Work as necessary for accepted substitution will be complete in all respects.
Submitted by: Lighting Dynamics Inc.
Signed by:
Ryan Huff
Firm:
Lighting Dynamics Inc.
Address:
7835 W Commercial Blvd, Tamarac, FL, 33351
Telephone:
954-944-0286
Attachments:
A/E’s REVIEW AND RECOMMENDATION
Approve Substitution - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Approve Substitution as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Reject Substitution - Use specified materials.
Substitution Request received too late - Use specified materials.
Signed by:
Date:
OWNER'S REVIEW AND ACTION
Substitution approved - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare Change
Order.
Substitution approved as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare
Change Order.
Substitution rejected - Use specified materials.
Signed by:
Additional Comments:
Other:
Date:
Contractor
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
Subcontractor
Page
Supplier
of
Manufacturer
A/E
Form Version: November 2010
CSI Form 13.1A
February 4, 2013
PRELIMINARY SHOP DRAWING PACKAGE
TH
552 NW 77 Street
Boca Raton FL, 33487
Fax: (561) 982.8323
Phone: (561) 989.5338
To: Ryan Huff @ Lighting Dynamics
RE: Port Canaveral Welcome Center
Urgent
For Review
Please Comment
Please Reply
X For Approval
Notes:
•
•
•
•
•
•
•
Initial approval is needed for the production to proceed.
• Sign off on all pages of the submittal is critical for the smooth transition from the
approval stage to the production stage
If the order is canceled after receipt of the shop drawings, payment equal to 10% or
$2500 (whichever is less) will be charged.
Check box for confirmation of input voltage or write in correction.
120 VAC
Cable Lengths will be provided as:
• Each power feed will be 6.5ft per UL requirements.
• DMX male/female cables to be 5ft. Extra cable provided by others.
• First DMX In cable (from Opto-Iso to 1st fixture) length: ________
Please indicate what number to start the DMX address.
• ________________________
HPCCS clips will be provided for this job.
• Each fixture utilizing clips will be supplied with 2 clips per.
• If more clips are needed/requested this may or may not require a change in PO
Per the Design Specification
Type LR1- Check boxes for confirmation or write in correction.
Fixture Type: HPCCS-RGB
Color Type: RGB
Optic Type: 10°x45° Beam Spread
Voltage: 120V
Finish Color: Clear Anodized
Interior Listed
Fixed Mounting Clips
Type LR2- Check boxes for confirmation or write in correction.
Fixture Type: SBL-Mix
Color Type: RGB
Optic Type: 24° Beam Spread
Voltage: 120V
Finish Color: Clear Anodized
Interior Listed
Hinge Mounting Clips
The information transmitted is intended only for the person or entity to which it is addressed and may contain confidential and/or
privileged material. Any review, retransmission, dissemination or other use of or taking of any action in reliance upon, this
information by persons or entities other than the intended recipient is prohibited. If you received this in error, please contact the
sender and delete the material from any computer.
*Please feel free to contribute any additional information to facilitate a smooth transition from the factory to the site, to
installation
th
552 NW 77 Street, Boca Raton, Florida 33487 (561) 989-5338 Fax (561) 982-8323
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
Type:
HPCCS-TRGB-10X45-120-A-IP65-FD-(4) RUNS@24 FT EACH
LR1(FEET)
Notes:
LDI12-6006
B CA FLASHER
HPCCS
PROJECT:_________________________________
Small Profile Color Changing LED Fixture
TYPE:____________________
Small Profile DMX controlled RGB fixture
The Boca HPCCS is a small profile fixture well suited for many lighting situations where both space and locating transformers are concerns, but color
changing is required. This line voltage version eliminates the need for secondary transformers, making installation contractor friendly. The HPCCS uses
Boca’s patented technology* for RGB additive color mixing. The housing is
anodized aluminum with a durable finish making it weather and abrasion resistant. It is UL Listed for dry or damp/wet location (model dependent).
* Patent Pending
Technical Specifications
Wattage ................... Per linear ft: Triple Diode= 12watts, White Mixing= 16watts, RGB= 24watts
Input Voltage ........................................................................................... 90-120VAC or 230-277VAC
Input Current .......................................................................................................... Model dependent
Control.................................................................................................................... Standard DMX 512
Power Cable Length .................................................................................................... UL Standard 6ft
DMX Cable Length .............................................................................................. Standard 5ft In/Out
LED Spacing, per strip ................................................................................................ 1.0”, on center
Fixture Length ...................................................................................................... 12.41”, 24.31”, 48.11”
Fixture Width ..................................................................................................................................... 2.70”
Total Height (not including clip) ................................................................................................ 2.11”
Mounting ............................................................................................................................................ Fixed
Color Options .................................. Alternating RGB, Triple Die RGB, Optics, White Mixing
Optics available ................................................. 10°, 24°, 36°, 10°x45°, 13°x38 ° (white only), 120 °
Exterior Wet Listing Options ....................................................................... IP65, IP68
Key Features
• Compact, rugged, linear fixture easily integrates into many applications
• Now available with triple die RGB boards and Satin Ice diffuser for direct
view application
• Many options in optics, color temperature, and accessories to suit a range
of projects - call factory for additional options
• Simple installation using conventional wiring
• Clear or soft diffused lens
• EMI Filter integral
• Uses standard DMX 512 controls
• Contact Boca Flasher for tips on custom installations
Mounting
Fixed Spring Clip Bracket
Hinge Bracket
White Mixing Options
• If specifying WM indicate white options here:
• White options are: 2700°K, 3000°K, 3500°K, 4000°K, 5000°K, amber
• Up to three different options can be specified.
Project Specification
A
HPCCS
Color Option:
Optic:
Voltage:
Finish:
Location:
RGB
Triple diode RGB =
TRGB* (*Pending),
White mixing = WM*
(*See above right)
90-120VAC = 120V
230-277VAC = 277V
Clear Anodized
Aluminum= A
(Check other options with Factory)
Mounting:
10°, 24°, 36°,
10°x45°, 13°x38°
(white only)°, 120°
Interior = I
Exterior (IP65) = E
Wet (IP68) = W
Fixed = F
Hinge = H
(Check Factory
for availability)
Options:
Soft Diffused Lens= D
Satin Ice Lens = SI
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.bocaflasher.com.
For specific requirements, contact your Boca sales representative.
Boca Flasher, Inc. 552 NW 77th Street Boca Raton, Florida 33487 USA Phone: 561.989.5338 Fax: 561.982.8323
© 2012 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners REV 091912
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
Type:
HPCCS-TRGB-10X45-120-A-IP65-FD-(4) RUNS@24 FT EACH
LR1(FEET)
Notes:
LDI12-6006
B CA FLASHER
HPCCS
PROJECT:_________________________________
TYPE:____________________
Additional Options
Satin Ice Lens
Diffused
White
Key Features:
Key Features:
• For use when more diffusion than our Satin
Ice Frost lens is needed
• Best for direct view use.
• Lens is 1/4” (.24) thick and adds 1/8” to overall height of fixture. Thinner lens available. Call
factory for more information
• 42% transmission
• Additional charges apply - consult your local
rep for more information.
• To specify add “SI” in options box
• For use when more diffusion than our clear
lens is needed
• Lens is 1/8” (.09) thick and adds 1/16” to overall height of fixture. Thicker lens available. Call
factory for more information
• 87% transmission
• Additional charges apply - consult your local rep
for more information.
• To specify add “D” in options box
Luminaire Information
FIXTURE TYPE: RGB, 10° X45° optic, 120V, 24 inch
Candela Distribution
Center Beam Candle Power & Illumination information
Polar Plot (Candela)
105
120
135
150 165
165 150
135
120
105
90
90
75
75
1500
60
60
3000
45
45
4500
15
180 Deg. Plane
Beam Width
10°
45°
4.5"
1'-8'
6.5"
2'-6"
8.5"
3'-4'
10"
4'-2"
1' -.5"
5'-0"
1'-3"
5'-9.5"
1'-5"
6'-7.5"
1'-7"
7'-5.5"
1'-9"
8'-3.5"
2'-1.5"
9'-11.5"
• Total Lumen Output:
1249 Lumens for 2 ft.
6000
30
Footcandles
Distance FtCandles
2 ft
1580.0
3 ft
702.2
4 ft
395.0
5 ft
252.8
6 ft
175.5
7 ft
129.0
8 ft
98.8
9 ft
69.5
10 ft
63.2
12 ft
43.9
0
15
270 Deg. Plane
0 Deg. Plane
30
90 Deg. Plane
• Luminaire Efficacy:
26.5 Lumens per watt
*For lux multiply footcandles by 10.76
*Foot candle reading taken at 100% capacity (no
dimming)
*Photometric information obtained 8-5-11 from LTL.
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.bocaflasher.com.
For specific requirements, contact your Boca sales representative.
Boca Flasher, Inc. 552 NW 77th Street Boca Raton, Florida 33487 USA Phone: 561.989.5338 Fax: 561.982.8323
© 2012 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
Type:
HPCCS-TRGB-10X45-120-A-IP65-FD-(4) RUNS@24 FT EACH
LR1(FEET)
Notes:
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
HPCCS
Installation Instructions
Indoor/Outdoor Line Voltage
IP65 IP68
Max temp: 55C
Min. temp: -40C
Model Dependent
Introduction:
Boca Flasher’s HPCCS is perfect for color washing long runs and large areas. LEDs
are spaced 1.00” apart in a two rows to create an even wide wash of light. The housing is anodized aluminum and is weather and abrasion resistant. This light fixture
can use any standard DMX 512 controller or can incorporate Boca Flasher’s Digital
Mainframe controller (Demo Version Only). The Digital Mainframe can run independently, creating many stand-alone color washing and solid color effects, as
well as responding to DMX commands for total control of your lighting experience.
Fixtures must be installed by a qualified and licensed electrican in accordance
with all national, state and local electrical codes and regulations. If any part of
this manual does not meet the necessary codes and regulations, contact the factory for more information before attempting to install.
MAINTAINENCE:
Cleaning: Use a soft cloth, clean surface with mild soap and water.
Storage: Store in a dry, well-ventilated area when product is not in use. Keep the electrical cord away from heated surfaces when in use or not in use. If cord shows signs of
damage do not use, return product to manufacturer.
1.
2.
3.
4.
ELECTRICAL SPECIFICATIONS
Input Voltage: 90-120VAC OR 230-277VAC (See layout drawings for spec.)
Total linear ft per 20A breaker: 50’
Total linear ft per 15A breaker: 38’
Input Current: 320mA RMS per linear ft for RGB, 220mA RMS per lin ft for WWA
INCLUDED IN THIS PACKAGE:
1
HPCCS Fixtures
(In lengths shown on job
specifc drawings)
2
Mounting Brackets
(1 bracket per fixture)
3
or
Turn off power before beginning installation.
1. Install Clips into Substrate
*For installation of
hinge see attachment.
Screw Information:
1. Screws not provided by Boca
Flasher.
2. Boca Flasher recommends wide
washer flat head Philips #8 screw
(not to exceed .418” diameter).
3. Length of screw will vary depending on mounting surface.
4. For outdoor installations,
installer should use a screw with
weatherproof coating.
2. Install Fixture Into Clips
Page 1 of 3
Job Specific Drawings
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
Type:
HPCCS-TRGB-10X45-120-A-IP65-FD-(4) RUNS@24 FT EACH
LR1(FEET)
Notes:
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
HPCCS
Installation Instructions
3. Connect Fixtures Together (as Shown on Job Specific Drawings)
3a.
Rotate fixture to
see bottom and
note each label.
3b.
Cross-reference
with job specific
drawing.
3c.
Connect DMX IN
on a fixture with
DMX out separate fixture.
3d.
Push together until
you hear a “Click”.
DMX Out
DMX In
DMX Out
Labels on fixtures
correspond with
nomenclatures on
drawings.
DMX In
DMX Out
Click!
Power Feed
DMX In
Note: Outdoor version will
screw together, not click.
4a. Connect Fixtures to Power- Single Run Installation
Note: Contractor cannot install more
than 32 fixtures per data stream.
Black (Line)
White (Neutral)
Note: More than one
connection can be made
in each connection box.
Black (Line)
White (Neutral)
Green (Ground)
Green (Ground)
Power Cable is 6.5ft
per UL standard
*Note: XLR 5 pin DMX connection standard. Cable
is typically 5 ft in length.
Call Factory for more
information.
RJ45 (ethernet) to an XLR
connection is available
upon request.
(5 ft)
(5 ft)
Page 2 of 3
(5 ft)
(5 ft)
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
Type:
HPCCS-TRGB-10X45-120-A-IP65-FD-(4) RUNS@24 FT EACH
LR1(FEET)
Notes:
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
HPCCS
Installation Instructions
4b. Connect Fixtures to Power- Multi Run Installation
Note: Contractor cannot install more
than 32 fixtures per data stream.
Note: More than one
connection can be made
in each connection box.
Power Cable is 6.5ft
per UL standard
Black (Line)
White (Neutral)
(XLR 5-pin)
White (Neutral)
Green (Ground)
(XLR 5-pin)
*Note: XLR 5 pin DMX connection standard. Cable
is typically 5 ft in length.
Call Factory for more
information.
RJ45 (ethernet) to an XLR
connection is available
upon request.
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
(5 ft)
Green (Ground)
5. Program DMX Addresses (Optional)
If using Boca Flasher PDMXC or Boca Flasher Digital Mainframe and require additional addressing or fixtures were not addressed at the factory see their respective manuals
Important Safety Reminders
1. DANGER: To reduce the risk electric shock, always unplug the HPCCS from electrical
outlet before cleaning. Cut breaker if outlet is not available.
2. To reduce the risk of burns, fire, electric shock, or injury to persons
• Use the HPCCS only for its intended use as described in these instructions. Do not
use attachments not recommended by Boca Flasher.
• Never operate the HPCCS if it has a damaged cord, cable or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. If the
seal appears to be damaged/broken/torn return the fixture to a service center for
examination or repair.
• Keep cables away from heated surfaces
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen is
being administered.
3. WARNING: Do not attempt to install or use the HPCCS without reading the installation instructions and safety labels. Failure to adhere to these instructions could
result in serious injury or property damage.
4. Do not modify, alter, or attempt to service the HPFCCS Doing so will void the warranty.
5. Do not use sharp tools near or on the fixture lens. Doing so will result in property
damage and void the warranty.
Page 3 of 3
Boca Flasher, Inc. 552 NW 77th Street Boca Raton, Florida 33487 USA Phone: 561.989.5338 Fax: 561.982.8323
© 2011 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners REV 090311
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000021-02
Type:
LR2
Notes:
LDI12-6006
Specifications
Due to continuous improvements and innovations, specifications may change without notice.
Item
Output
Electrical
Control
Specification
Details
Beam Angle
10° / 23° / 36° / 86°
Lumens*
1418 (10° clear lens) 1222 (23° frosted lens) 1217 (36° frosted lens) 1471 (86° no optic)
LED Channels
Red / Green / Blue
Mixing Distance
6 in (152 mm) to uniform light
Lumen Maintenance†
50,000+ hours L50 @ 50° C (full output)
Input Voltage
100 – 240 VAC, auto-switching, 50 / 60 Hz via Data Enabler Pro
Power Consumption
50 W maximum at full output, steady state
Power Factor
.98 @ 120 VAC
Interface
Data Enabler Pro (DMX / Ethernet)
Control System
Philips full range of controllers, including Light System Manager, iPlayer 3, and ColorDial Pro, or third-party controllers
Dimensions
(Height x Width x Depth)
Physical
Certification
and Safety
110º
110º
10º Beam Angle
23º Beam Angle
110º Rotation
110º
110º
36º Beam Angle
86º Beam Angle
7.1 x 12.5 x 4.9 in (172 x 317 x 125 mm)
Weight
6.4 lb (2.9 kg)
Effective Projected Area
(EPA)
0.05211 m2
Housing
Die-cast aluminium, powder-coated finish
Lens
Clear tempered glass (10° and 86° beam angles)
Frosted tempered glass (23° and 36° beam angles)
Fixture Connections
6 ft (1.8 m) unified power / data cable
Temperature Ranges
-40° – 122° F (-40° – 50° C) Operating
-4° – 122° F (-20° – 50° C) Startup
-40° – 176° F ( -40° – 80° C) Storage
Humidity
0 – 95%, non-condensing
Fixture Run Lengths
To calculate fixture run lengths and total power consumption
for your specific installation, download the Configuration
Calculator from www.philipscolorkinetics.com/support/
install_tool/
Certification
UL / cUL, FCC Class A, CE, PSE
Environment
Dry / Damp / Wet Location, IP66
12.5 in
318 mm
* Lumen measurement complies with IES LM-79-08.
† L 50 = 50% lumen maintenance (when light output drops below 50%
of initial output). Ambient luminaire temperatures specified. Lumen
maintenance calculations are based on lifetime prediction graphs supplied by LED source manufacturers.
Calculations for white-light LED fixtures are based on measurements that comply with IES LM-80-08
testing procedures. Refer to www.philipscolorkinetics.com/support/appnotes/ for more information.
6.5 in
165 mm
0.65 in
17 mm
4.75 in
121 mm
1.35 in
34 mm
7.1 in
180 mm
4.9 in
124 mm
6.5 in
165 mm
3.9 in
99 mm
7.25 in
184 mm
6
ColorBlast Powercore Product Guide
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000021-02
Type:
LR2
Notes:
LDI12-6006
Fixtures and Data Enabler Pro
ColorBlast Powercore fixtures are part of a complete system which includes:
• One or more Data Enabler Pro devices
Included in the box
ColorBlast Powercore fixture
(2) 8-32 screws for indoor installation
(4) 10-24 stainless steel screws for outdoor installation
1/8 in hex key wrench for fixture positioning
and locking
Junction box gasket
• Any Philips controller, including Light System Manager, iPlayer 3, and ColorDial
Pro, or a third-party controller
• 4-conductor copper wire to connect ColorBlast Powercore fixtures in series or in
parallel. Standard 12 AWG (2.05 mm) stranded wire is recommended.
Item
Installation Instructions
Type
10° (clear lens)
23° (frosted lens)
ColorBlast Powercore
UL / cUL / CE / PSE
36° (frosted lens)
86° (no optic)
10° clear lens
ColorBlast Powercore
CQC
23° frosted lens
36° frosted lens
86° no optic
Data Enabler Pro
Housing Color
Item Number
Philips 12NC
White
123-000021-00
910503702321
Black
123-000021-01
910503702350
White
123-000021-02
910503702334
Black
123-000021-03
910503702351
White
123-000021-04
910503702352
Black
123-000021-05
910503702353
White
123-000021-06
910503702354
Black
123-000021-07
910503702355
White
123-000021-08
910503702434
Black
123-000021-09
910503702435
White
123-000021-10
910503702436
Black
123-000021-11
910503702437
White
123-000021-12
910503702827
Black
123-000021-13
910503702828
White
123-000021-14
910503702829
Black
123-000021-15
910503702830
3/4 in / 1/2 in NPT (U.S. trade size conduit)
106-000004-00
910503701210
PG21 / PG13 (metric size conduit)
106-000004-01
910503701211
Use Item Number when ordering in North America.
Typical ColorBlast Powercore system installation
For detailed wiring diagrams visit www.philipscolorkinetics.com/support/wiring/ls_prod.html
Controller Keypad
iPlayer 3
Controller
OFF
AuxBox
iPLAYER
OX
AUXB
STATUS
2
3
4
5
6
7
2
SERIAL
3
PRESET
3
S
8
INPUTS
4
5
PORT
ColorBlast Powercore fixtures
X
24 VDC
+/ -
ColorPlay 3
Software
USB
PO
WER
DMX Control 2
to fixtures
DMX Control 1
to fixtures
Line voltage
Fixture
Cable
Data Enabler Pro
ColorBlast Powercore Product Guide
7
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000021-02
Type:
LR2
Notes:
LDI12-6006
Installation
ColorBlast Powercore offers rich, saturated wall-washing color and color-changing
effects with Powercore technology. Powercore, which integrates LED power and
data management within the fixture, eases installation by eliminating the need for
external power supplies.
Owner / User Responsibilities
It is the responsibility of the contractor, installer, purchaser, owner, and user to
install, maintain, and operate ColorBlast Powercore fixtures in such a manner as to
comply with all applicable codes, state and local laws, ordinances, and regulations.
Consult with the appropriate electrical inspector to ensure compliance.
E Refer to the ColorBlast Powercore
Installation Instructions for specific warning
and caution statements.
Installing in Damp or Wet Locations
When installing in damp or wet locations, it is good practice to seal all fixtures and
junction boxes with electronics-grade RTV silicone sealant to ensure that moisture
cannot enter or accumulate in wiring compartments, cables, or other electrical parts.
You must use suitable outdoor-rated junction boxes when installing in damp or wet
locations. Additionally, you must use gaskets, clamps, and other parts required for
installation to comply with all applicable local and national codes
Create a Lighting Design Plan
and Layout Grid
1. Determine the appropriate location of each Data Enabler Pro in relation to the
light fixtures, and of the light fixtures in relation to each other.
E To streamline the configuration of
complex installations, record the serial
number (DMX) or IP address (Ethernet)
and location of each Data Enabler Pro.
ColorBlast Powercore fixtures can be installed in series or in parallel (wired to
a common junction box). The maximum number of fixtures each Data Enabler
Pro can support depends on specific configuration details such as fixture spacing,
circuit size, line voltage, and method of connection (in series or in parallel). For
more information, and for help calculating the number of fixtures your specific
installation can support, download the Configuration Calculator from www.
colorkinetics.com/support/install_tool/, or consult Application Engineering
Services at support@colorkinetics.com.
In addition to maximum fixture run lengths determined by the electrical
configuration, each Data Enabler Pro imposes maximum run lengths based on
data integrity. To ensure data integrity, maximum individual run length should not
exceed 175 feet (53.3 m), and the total cable length per Data Enabler Pro should
not exceed 400 feet (122 m).
Fixtures
Fixtures
DataData
Enabler
Enabler
Pro Pro
Fixtures
Fixtures
DataData
Enabler
Enabler
Pro Pro
Data Integrity —Data
maximum
individual
length
175
ft 175
(53.3
m)
—
total
400
ft 400
(122
m)
Data
Integrity
– maximum
individual
length
175
ft (53.3
Integrity
– total
length
ft (122
Integrity
– maximum
individual
length
ft (53.3
m) m)Data Integrity
DataData
Integrity
–length
total
length
400
ft (122
m) m)
Leader Cable connector dimensions
.375 in
(9.5 mm)
2. On an architectural diagram or other diagram that shows the physical layout of
the installation, identify the locations of all switches, controllers, Data Enabler Pro
devices, fixtures, and cables.
18 AWG
.04 in (1 mm)
ColorBlast Powercore Product Guide
9
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000021-02
Type:
LR2
Notes:
LDI12-6006
3. Each ColorBlast Powercore fixture comes pre-programmed with a unique serial
number. As you unpack the fixtures, record the serial numbers in a layout grid
(typically a spreadsheet or list) for easy reference and light addressing.
COLORBLAST® 12 POWERCORE
Designed and developed in the USA. Made in Mexico.
Item: 123-000009-08
12NC: 910503700162
AGRD eeer DVSR DDwe 25erf
5RDE wpoc 10943
DC:
0852 SCD 1324
1324
22
4. Assign each fixture to a position in the lighting design plan.
5. To streamline installation and aid in light show programming, you can affix a
weatherproof label identifying the order or placement in the installation to an
inconspicuous location on each light fixture’s housing.
Start the Installation
1. Install all Data Enabler Pro devices, including any interfaces with controllers. Data
Enabler Pro devices and external controllers send power and control signals to
the fixtures over the single fixture cable. Additional cabling is required to connect
fixtures together in series.
E For complete instructions on how to wire
the Data Enabler Pro, refer to the Data
Enabler Pro Product Guide or Installation
Instructions.
2. Verify that all additional supporting equipment (switches, controllers) is in place.
3. Ensure that all additional parts and tools are available, including:
• The included 8-32 screws for indoor installations, or the 10-24 stainless steel
screws for outdoor installations
• The included 1/8 hex key wrench
Included in the box
• The included junction box gasket
ColorBlast Powercore fixture
• In the US, one 4 in (102 mm) round US electrical junction box per fixture,
rated for your application, with 3.5 in (89 mm) center-to-center screw holes
for attaching the fixture’s base. (Refer to the junction box manufacturer’s
literature for additional items required for mounting or sealing.)
(2) 8-32 screws for indoor installation
• A sufficient length of 12 AWG (2.05 mm), 4-conductor stranded copper wire
Installation Instructions
(4) 10-24 stainless steel screws for outdoor installation
1/8 in hex key wrench for fixture positioning
and locking
Junction box gasket
• Conduit as required
• Electronics-grade room temperature vulcanizing (RTV) silicone sealant
E When installing ColorBlast Powercore
fixtures, the input earth ground, canopy
earth ground, and fixture cable earth ground
must all be connected together.
10
ColorBlast Powercore Product Guide
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
123-000021-02
Notes:
Type:
LR2
LDI12-6006
8. Run the wiring from the first junction box in the series to the Data Enabler Pro,
or, if installing in parallel, run the wiring from the common junction box to the
Data Enabler Pro. Secure connections within the Data Enabler Pro housing.
Data Enabler Pro
9. Secure the Data Enabler Pro cover. If installing in a wet or damp location, seal the Data Enabler Pro with electronics-grade RTV silicone sealant.
Power / data output to fixtures
L
N
L
N
DMX
L N
DMX
L N
12
ColorBlast Powercore Product Guide
L N
L
Line Voltage
Tension de secteur
Netzspannung E Refer to the Data Enabler Pro
Tensión de líneaProduct Guide for comprehensive
installation and configuration instructions.
Tensione di linea
Netspanning You can view or download the guide
from www.philipscolorkinetics.com/ls/
ᒵၴሽ䝟
pds/dataenablerpro
优ሁ䶣㣉
Neutral
Neutral
Mains voltage output Neutro
Neutro
N
Neutraal
中性線
零线
Ground
Terre
Masse
Toma de tierra
Terra
Aarde
アース
接地
Catalog Number:
SUBSTITUTION FORM
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
LR2
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase)
Project: Port Canaveral Welcome Center
Substitution Request Number:
From:
To:
Lighting
Incorporated
Date:
GWWO Architects/ Henry Adams Cons. Engineers
11/30/12
A/E: Project Number:
Re:
Dynamics
Contract For:
Lighting Dynamics Inc.
1124
Port Canaveral Welcome Center
Specification Title: Substitution Procedures
Description: Substitutions
Section: 012500
Article/Paragraph:
Page: 18
1.1-1.4
Proposed/Substitution:
Manufacturer:
Model #:
Installer:
History:
BOCA FLASHER
Address:
Available upon request
SBL-MIX-RGB-24DEGREES-120V-WHITE-1FT-50W-FROSTED LENS
Gerelco Electrical Contractors
New product
Address: 560 NW Enterprise Drive, Port Saint Lucie,FL,34986 Phone: 772-340-7474
1-4 years old
5-10 years old
Differences between proposed substitution and specified product:
More than 10 years old
Product is comparable in performance, design & aesthetics
Point-by-point comparative data attached — REQUIRED BY A/E
Reason for not providing specified item: We don’t represent the specified manufacturer, we are providing a comparable product
In design, performance & aesthetics
Similar Installation: This product has been used on numerous projects in size and scope comparable to this project. Additional information is
available upon further request from Architect & Engineer.
Project:
Available upon request
Architect: Available upon request
Address:
Owner:
N/A
Date Installed: N/A
Proposed substitution affects other parts of Work:
No
Yes; explain
Savings to Owner for accepting substitution: Alternate Equal
Proposed substitution changes Contract Time:
Supporting Data Attached:
Drawings
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
No
Yes [Add]
Product Data
Samples
Page
of
($ 0
).
[Deduct]
days.
Tests
Reports
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
LR2
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase
— Continued)
The Undersigned certifies:
• Proposed substitution has been fully investigated and determined to be equal or superior in all respects to specified product.
• Same warranty will be furnished for proposed substitution as for specified product.
• Same maintenance service and source of replacement parts, as applicable, is available.
• Proposed substitution will have no adverse effect on other trades and will not affect or delay progress schedule.
• Cost data as stated above is complete. Claims for additional costs related to accepted substitution which may subsequently become
apparent are to be waived.
• Proposed substitution does not affect dimensions and functional clearances.
• Payment will be made for changes to building design, including A/E design, detailing, and construction costs caused by the substitution.
• Coordination, installation, and changes in the Work as necessary for accepted substitution will be complete in all respects.
Submitted by: Lighting Dynamics Inc.
Signed by:
Ryan Huff
Firm:
Lighting Dynamics Inc.
Address:
7835 W Commercial Blvd, Tamarac, FL, 33351
Telephone:
954-944-0286
Attachments:
A/E’s REVIEW AND RECOMMENDATION
Approve Substitution - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Approve Substitution as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Reject Substitution - Use specified materials.
Substitution Request received too late - Use specified materials.
Signed by:
Date:
OWNER'S REVIEW AND ACTION
Substitution approved - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare Change
Order.
Substitution approved as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare
Change Order.
Substitution rejected - Use specified materials.
Signed by:
Additional Comments:
Other:
Date:
Contractor
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
Subcontractor
Page
Supplier
of
Manufacturer
A/E
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
B CA FLASHER
SBL-Mix
High Intensity Color or White Mixing LED Fixture
PROJECT:_________________________________
TYPE:____________________
Dimmable high intensity color changing line voltage fixture
fabricated with a variety of options.
The Boca SBL-Mix is a powerful instrument developed for large-coverage illumination. This line voltage fixture* eliminates the need for secondary transformers, making installation contractor friendly. SBL-Mix can be fabricated
with a range of optics and color temperature choices, affording a multitude
of distribution and effect options. The SBL-Mix uses Boca’s patented technology* for RGB additive color mixing. The housing is anodized aluminum with a
durable finish making it weather and abrasion resistant. It is UL Listed for dry,
damp, or wet location. (model dependent).
*Patent Pending
Technical Specifications
Sizes available .....................................................................................................................1 ft, 2 ft, 4 ft
Wattage ......................................................................... 48-96 watts per lin. ft (model dependent)
Input Voltage ............................................................................................. 90-120VAC, 230-277VAC
Control ...................................................................................................................... Standard DMX 512
Power Cable Length .................................................................................................... UL Standard 6ft
DMX Cable Length ............................................................................................................ Standard 5ft
Fixture Length ...................................................................................................... 12.85”, 24.70”, 48.41”
Fixture Width ....................................................................................................................................... 7.51”
Total Height (including base) ........................................................................................................ 6.00”
Mounting .......................................................................................................................... Hinge Bracket
Color Options ........................................................................................................... White mixing, RGB
Optics available ...............................................10°, 24°, 36°, 10°x45°, 13°x38° (white only), 120°
Exterior Wet Listing Options ....................................................................... IP65, IP68
Key Features
• Compact, variable light fixture for dry, damp, or wet location use
• Fixture comes in 1 foot, 2 foot and 4 foot options
• Many options in optics, color temperature, and accessories to suit a range
of projects - call factory for additional options
• Uses standard DMX 512 controls
• Clear or soft diffused lens
• Simple installation using conventional wiring
• Contact Boca Flasher for tips on custom installations
Mounting
White Mixing Options
• If specifying WM indicate white options here:
• White options are: 2700°K, 3000°K, 3500°K, 4000°K, 5000°K, amber
• Up to three different options can be specified
Project Specification
SBL
H
Mix
Color Option:
Optic:
Voltage:
Finish:
Location:
Mounting:
10°, 24°, 36°,
10°x45°, 13°x38
(white only)°, 120°
90-120VAC = 120V
230-277VAC = 277V
Anodized
Aluminum= A
Black= B
(Check Availability
with Factory)
Interior = I
Exterior (IP65) = E
Wet (IP68) = W
Options:
RGB,
White mixing= WM*
(*See Above)
Hinge Bracket
Soft Diffused
Glass Lens= D*
*Special order only
We are constantly improving our fixtures and reserve the right to change options and specifications. Additional information & details at www.bocaflasher.com.
For specific requirements, contact your Boca sales representative.
Boca Flasher, Inc. 552 NW 77th Street Boca Raton, Florida 33487 USA Phone: 561.989.5338 Fax: 561.982.8323
© 2012 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners REV 100412
Type LR2-Photometric Distribution Report
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
SBL-Mix
Installation Instructions
WARNING:
Do Not Lift
Fixtures By
Cables.
This could result in permanent damage to
both the fixture and the cables. Damage
resulting from grasping cables and/or
putting undue pressure on the cable
connections will not be covered under the
warranty.
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
SBL-Mix
Installation Instructions
High Power DMX Controlled Washer
IP65 IP68
Model Dependent
Max temp: 55C
Min. temp: -40C
Introduction:
The Boca SBL-Mix is a powerful instrument developed for large-coverage illumination.
This line voltage fixture eliminates the need for secondary transformers, making installation contractor friendly. The housing is anodized aluminum with a durable finish
making it weather and abrasion resistant. The SBL-Mix is UL Listed for dry, damp, or
wet location (model dependent).
Fixtures must be installed by a qualified and licensed electrican in accordance
with all national, state and local electrical codes and regulations. If any part of
this manual does not meet the necessary codes and regulations, contact the factory for more information before attempting to install.
MAINTAINENCE:
Cleaning: Use a soft cloth, clean surface with mild soap and water.
Storage: Store in a dry, well-ventilated area when product is not in use. Keep the electrical cord away from heated surfaces when in use or not in use. If cord shows signs of
damage do not use, return product to manufacturer.
1.
2.
3.
4.
ELECTRICAL SPECIFICATIONS
Input Voltage: 90-120VAC OR 230-277VAC (See layout drawings for spec.)
Total linear ft per 20A breaker: 20’
Total linear ft per 15A breaker: 15’
Input Current: 640mA RMS per linear ft
INCLUDED IN THIS PACKAGE:
SBL-Mix Fixtures
1
(In lengths shown on job
specifc drawings)
2
Mounting Brackets
(2 bracket per fixture)
3
Job Specific Drawings
Power cord
length is
6.5ft per UL
standard
Turn off power before beginning installation.
DO NOT LIFT FIXTURE BY CABLES!
Damage resulting from handling fixture by cables is not covered under the warranty.
1. Install Hinges on Fixtures
Hinge Clips
Use four screws (provided by Boca Flasher)
to secure the fixcture
to the brackety
Page 1 of 4
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
SBL-Mix
Installation Instructions
2. Install Hinges into Substrate
2a
2a
Use four screws
(not provided
by Boca Flasher) to secure
the brackets to
the substrate
Loosen center
hinge pin and
adjust angle of
fixture to focuse required.
Tighten pin to
hold the focus.
Screw Information:
1. Screws not provided by Boca Flasher.
2. Boca Flasher recommends wide washer flat head Philips screws not to exceed .418” diameter.
3. Length of screw will vary depending on mounting surface.
4. For outdoor installations, installer should use a screw with weatherproof coating.
3. Arrange Fixtures in Order Necessary
3a
Rotate fixture to
see bottom and
note each label.
3b
Labels on fixtures
correspond with
nomenclatures on
drawings.
Cross-reference
with job specific
drawing.
3C
Second label contains job name, fixture type
on architectural plans, entire specification, as
well as a QR bar code. Scan code fore more info
on the project.
Scan this with any QR reader on
your smartphone to download
more copies of the install manual
& see info about the product.
LT4-1
Fixtures come preaddressed. DMX
addresses must run
in correct order.
Page 2 of 4
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
SBL-Mix
Installation Instructions
4. Connect Fixtures Together (as Shown on Job Specific Drawings)
4a
Connect DMX IN
on a fixture with
DMX out separate fixture.
Push together until
you hear a “Click”.
4b
DMX Out
DMX In
DMX Out
DMX In
DMX Out
Click!
DMX In
Power Feed
5a. Connect Fixtures to Power- Single Run Installation
Note: Contractor cannot install more
than 32 fixtures per data stream.
Note: Outdoor version will
screw together, not click.
Black (Line)
White (Neutral)
Black (Line)
White (Neutral)
Green (Ground)
Green (Ground)
Page 3 of 4
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SBL-MIX-RGB-24DEGREES-120VWHITE-1FT-50W-FROSTED LENS
Notes:
Type:
LR2(FEET)
LDI12-6006
552 NW 77th Street
Boca Raton, FL 33487
561-989-5338
www.bocaflasher.com
B CA FLASHER
SBL-Mix
Installation Instructions
5b. Connect Fixtures to Power- Multi Run Installation
Note: Contractor cannot install more
than 32 fixtures per data stream.
Black (Line)
Black (Line)
White (Neutral)
White (Neutral)
Green (Ground)
Green (Ground)
5. Program DMX Addresses (Optional)
If using Boca Flasher PDMXC or Boca Flasher Digital Mainframe and require additional addressing or fixtures were not addressed at the factory see their respective manuals
Important Safety Reminders
1. DANGER: To reduce the risk electric shock, always unplug the SBL-Mix from electrical outlet before cleaning. Cut breaker if outlet is not available.
2. To reduce the risk of burns, fire, electric shock, or injury to persons
• Use the SBL-Mix only for its intended use as described in these instructions. Do
not use attachments not recommended by Boca Flasher.
• Never operate the SBL-Mix if it has a damaged cord, cable or plug, if it is not
working properly, if it has been dropped or damaged, or dropped into water.
If the seal appears to be damaged/broken/torn return the fixture to a service
center for examination or repair.
• Keep cables away from heated surfaces
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or where oxygen
is being administered.
3. WARNING: Do not attempt to install or use the SBL-Mix without reading the installation instructions and safety labels. Failure to adhere to these instructions
could result in serious injury or property damage.
4. Do not modify, alter, or attempt to service the SBL-Mix. Doing so will void the
warranty.
5. Do not use sharp tools near or on the fixture lens. Doing so will result in property damage and void the warranty.
Page 4 of 4
Boca Flasher, Inc. 552 NW 77th Street Boca Raton, Florida 33487 USA Phone: 561.989.5338 Fax: 561.982.8323
© 2012 Boca Flasher, Inc. All rights reserved. All names and trademarks are property of their respective owners REV 100412
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
STICK DMX CONTROLLER
Type:
LR1/LR2
Notes:
LDI12-6006
Sunlite Touch-sensitive Intelligent Control Keypad
Technical datasheet
Revision date 26 Sep. 2012
Ref. STICK-DE3
Page 1/4
www.nicolaudie.com
Version 1.0
Rechargeable
battery
106 mm
Touch-sensitive
user interface
Screw-terminal
rear connector
(5 pins)
Extension socket
rear connectors
(2x10 pins)
146
mm
Power+DMX
socket
(RJ45)
Ethernet socket
(RJ45)
Front access
connections
11 mm
Package
Interface, sdcard, datasheet, cdrom, usb cable
Software
ESA + ESA PRO on PC/Windows,
Mobile Apps
Available colors
Options
mini
usb
reset micro dmx
button SD
led
Black frame, various front panel design
See the OPTIONS table
Standards
data
led
EC, EMC, ROHS, ETL, UL (some are in process)
Temperature
-10ºC to 45ºC
Dimensions
146x106x11 mm
Weight
CONNECTION
SPECIFICATIONS
Built-in
features
Screw-terminal
rear connector
(5 pins)
Power Supply
6V DC 0.6A, optional
•
First universe, 512 channels DMX512 output
•
DMX Output #2
Second universe, 512 channels DMX512 output
Ethernet
Complete package 177x146x48 mm
247 g 8.71 oz
DMX Output #1
USB
ESA2 on PC + MAC
DMX Lightpad 3 + ARCOLIS on iPhone/iPad/Android
Complete package 492 g 17.4 oz
Extension
socket
rear connectors
(2x10 pins)
Power+DMX
socket
(RJ45)
Ethernet
socket
(RJ45)
•
•
•
•
•
USB
•
USB communication for PC/Mac software
•
Advanced networking features
Ports 1,2,...,8
8 Contact closure inputs, connect to ground for operating
User interface
10 buttons, 1 wheel, 1 color display, 5 leds
(Touch-sensitive keypad)
Micro sd card for stand alone memory use (supplied)
RESET
Push button for feet operation
RS232
RS232 serial communication for external synchronisation
Automatic standby 5V signal
Clock
Real-time clock and calendar
•
power/data
leds
•
SD card
Output relay
Front access
connections
•
•
•
•
•
OPTIONS / ACCESSORIES
RJ2BLOCK
RJ45 to connector block converter for POWER+DMX
POWER4M
Dedicated power adapter 110-220V to 6VDC
VERSIONS
WHITE OR BLACK front panel, choices of wheel design
© Nicolaudie-Sunlite 1989-2012. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
STICK DMX CONTROLLER
Type:
LR1/LR2
Notes:
LDI12-6006
Sunlite Touch-sensitive Intelligent Control Keypad
Technical datasheet
Revision date 26 Sep. 2012
Ref. STICK-DE3
Page 2/4
www.nicolaudie.com
Version 1.0
EASY INSTALLATION
1. Mount an electrical box
inside the wall
The S.T.I.C.K. controller can be installed in any standard
electrical backbox. If you use a double size box,
you can insert the power supply inside.
2. Connect the wires
POWER: Connect a 5.5V or 6V DC 0.6A.
Be sure to not invert the + and the ground.
DMX: Connect the DMX cable to the lighting
receivers (Leds, Dimmers, Fixtures..)
(for XLR: 1=ground 2=dmx- 3=dmx+)
3. Mount the interface on the wall
First, mount the back side of the interface on the wall with 2 or more screws
Secondly, plug the connectors :
- Ethernet cable
- DMX and power (connector block or RJ45)
POWER+DMX
with the
connector block
POWER
DC +
POWER
Ground
DMX
Ground
DMX DMX +
POWER+DMX
with the
RJ45 cable
1 DMX +
1.......8
POWER
2 DMX +DMX
3 DMX2 +
4 POWER
5 DC +
6 DMX2 7 POWER
8 GROUND
(
(
© Nicolaudie-Sunlite 1989-2012. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
STICK DMX CONTROLLER
Type:
LR1/LR2
Notes:
LDI12-6006
Sunlite Touch-sensitive Intelligent Control Keypad
Technical datasheet
Revision date 26 Sep. 2012
Ref. STICK-DE3
Page 3/4
www.nicolaudie.com
Version 1.0
2x10 pins EXTENSION connector
DMX CHIPS can be
replaced here
VIN
GND
IR_RX
3.3V
Relay
DMX2+
DMX2DMX1+
DMX1GND_DMX
DMX
universe #1
DMX
universe #2
Ref: SP485ECN-L
MAX485 CSA
BLACKOUT relay
(energy saving)
using the 2 pins : BK
and G (GND)
20
18
16
14
12
10
8
6
4
2
19
17
15
13
11
9
7
5
3
1
PORT1
PORT2
PORT3
PORT4
PORT5
PORT6
PORT7
PORT8
RS232 RX
RS232 TX
Compatible connectors:
WURTH ELEKTRONIK ref: 61301021121
MOLEX ref: 10-89-7202
TE Connectivity ref: 1-87227-0
FCI ref: 77313-101-20LF
HARWIN ref: M20-9981046
SAMTEC ref: TSW-110-xx-T-D
FARNELL ref: 1841232
RS ref: 763-6754 673-7534 251-8165
MOUSER ref: 538-10-89-7202
DIGIKEY ref: WM26820-ND
Example of relay : FINDER
Ref. 22.23.9.012.4000
http://www.findernet.com/fr/products/
profiles.php?serie=22&lang=en
RS232 triggering
Make a cable using the 3 pins : TX, RX and G (GND)
Set the RS232 parameters to : 9600bds 8 bits, no Parity, 2 Stop bits
- To play a scene, send 3 bytes : 1 x 255
(x = scene number)
- To stop a scene, send 3 bytes : 2 x 255
(x = scene number)
- To pause a scene, send 3 bytes :
3 x 255
(x = scene number)
- To release a pause, send 3 bytes :
4 x 255
(x = scene number)
- To reset a scene, send 3 bytes : 5 x 255
(x = scene number)
Note: the scene number (x) can be from 1 to 40. For instance, 11 means Page B Scene #3
PORTS triggering
It is possible to start scenes using the input ports (contact closure). To activate a port, a brief
contact must be established between the ports (1...8) and the ground (GND). This is a contact
closure so there is no need to hold the connection, it acts like a basic switch.
P1 P2 P3 P4 ...
GND
© Nicolaudie-Sunlite 1989-2012. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
STICK DMX CONTROLLER
Type:
LR1/LR2
Notes:
LDI12-6006
Sunlite Touch-sensitive Intelligent Control Keypad
Technical datasheet
Revision date 26 Sep. 2012
Ref. STICK-DE3
Page 4/4
www.nicolaudie.com
Version 1.0
INTERNAL MENU (hardware configuration)
Button >
Button <
ZONE+
ZONE-
Press and hold the ON/OFF button for 3 seconds to get into the settings menu. Here are the available parameters:
- Mode (M) : allows to enable/disable speed/dimmer/...buttons
- Arrows (A) : allows to change the function of < and > arrows
- Palet (P) : allows to enable/disable the palet functions (speed/dimmer/color)
- Scene (S) : allows to change various settings (fade time, pause/stop...)
- First Start (F) : allows to setup what to do at startup (play a scene, blackout, etc...)
- Trigger (T) : allows to enable/disable triggers (RS232, IR, ports...)
- Ethernet (E) : allows to setup Ethernet parameters (IP address...)
- Date/Time (T) : allows to change date and time of the device
- Graphics (G) : allows to change the display settings (sleep mode, brightness...)
- DMX output (X) : allows to change the DMX signal parameters (speed...)
- Diagnostic : shows the date/time, firmware version...
- Reset : allows to reset the unit to factory settings
The < and > arrows allows you to move the cursor in the menu or change a value, the ZONE+ buttons allows you to
edit/validate a value or enter a submenu, the ZONE- button allows you to return to the previous menu/submenu (read
the hardware manual for a complete description).
SOFTWARE and LINKS
ARCOLIS sofware (Touch Lighting Editor app for iPhone/iPad, Android)
DMX Lightpad 3 (Remote application for iPhone/iPad, Android, Windows)
=>download your application from Google Play, Apple App Store or Windows Mobile website
ESA, ESAPRO software (Windows)
www.nicolaudie.com (-> Support -> Downloads)
ESA2 software (Windows, Mac)
www.nicolaudie.com (-> Support -> Downloads)
ESA, ESAPRO manualswww.nicolaudie.com/manuals.php
Driver, Firmware, Toolswww.nicolaudie.com/hardware.php
© Nicolaudie-Sunlite 1989-2012. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
S22DR-L-L40-ETG-2-U-ED-S92HT
Type:
M
Notes:
LDI12-6006
NEO-RAY
DESCRIPTION
A return to simplicity, elegance and minimalism ... Slender lines of LED light
set in an architectural environment are the essence of Straight and Narrow.
This series accommodates most architectural lighting design applications.
Generation II enhancements and new features:
- Extruded housing offers precise in-line appearance and enhanced rigidity
- LED offers a continuous uninterrupted line of light with no shadows
- Flush lay in lens provides clean look and easy maintenance
Type
Catalog #
Project
Date
Comments
Prepared by
SPECIFICATION FEATURES
Construction
Extruded aluminum housing.
Nominal 2', 3', 4', 6' or 8'
illuminated sections. Used in run
configuration and/or individual
fixtures
Electrical
(120-277) Voltage electronic driver.
Fixtures and electrical components
certified to UL and CUL standards.
Damp location rated.
Shielding
Trimless, lay-in, high transmission
diffuser.
Finish
Durable, low gloss, white, powder
coated acrylic. Optional custom
finish.
Mounting
Recessed. Specify:
(ETG) 15/16" Exposed T-grid
(STG) 9/16" Screw Slot Grid
(SR) Sheet Rock (Flanged)
(FSR) Flangeless Sheet Rock
(FTG) 9/16" Exposed T-grid
22DR
Straight &
Narrow
LED
SUPPORT WIRE
(BY OTHERS)
2 83 "
Individual
Recessed
Direct
Light Distribution:
Indirect = 0%
Direct = 100%
4"
3"
S22DR LED (ETG)
ORDERING INFORMATION
SAMPLE
NUMBER:
22
S22DR-1-L35-ETG-6-U-DD-S92HT
D
Series
22 =Straight & Narrow
Light Distribution
D=Direct
R
Mounting
R =Recessed
Lamp Type
L30=LED, 3000K
L35=LED, 3500K
L40=LED, 4000K
Light Level
(Values Reflect 3500K, 4’ Fixture)
1= Level 1, 2100 Lumens, 33 Watts
2= Level 2, 2700 Lumens, 45 Watts
Ceiling Type
ETG =15/16”
exposed T-grid
STG = Slot T-grid
SR =Sheet Rock
(Flanged)
FSR=Sheet Rock
(Trimless)
FTG =9/16”
exposed T-grid
Voltage
1=120V
2=277V
U =Universal
Length
2 = 2’
3 = 3’
4 = 4’
6 = 6’
8 = 8’
Driver 1
ED =Electronic Driver
DD=Dimming Driver
Shielding Options
S92HT =High transmission lens
1 Required voltage information.
• For dimming, specify driver option
• EM Packs and J47V transformers must be remote mounted.
• Level 1 is not available in universal voltage for some fixture lengths. Please, consult factory.
• Acrylic lenses will be slightly shorter than housing length at ambient temperature in order to compensate for normal thermal expansion during operation
Specifications and Dimensions subject to change without notice.
Consult your representative for additional options and finishes.
ADN101862
09/19/2011 4:13:28 PM
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
S22DR-L-L40-ETG-2-U-ED-S92HT
Type:
M
Notes:
LDI12-6006
Straight & Narrow - Gen II 22DR LED Individual
PHOTOMETRICS
22DR LED
S22DR-1L35-4D-S92HT
Zonal Lumen Summary
LEGEND:
0-deg:
45-deg:
90-deg:
90˚
75˚
450
60˚
45˚
1350
0˚
15˚
%Lamp
%Fixt
0-30
0-40
0-60
0-90
0-180
703.55
1092.83
1741.51
2095.32
2095.32
N.A.
N.A.
N.A.
N.A.
N.A.
33.60
52.20
83.10
100.00
100.00
33
1.00
Direct
1.18
1.04
1.20
Rectangular
Zonal Lumen Summary
LEGEND:
0-deg:
45-deg:
90-deg:
90˚
75˚
450
60˚
Angle
0
5
10
15
25
35
45
55
65
75
85
90
0
977
984
966
935
836
696
535
377
238
122
35
0
45
977
970
947
907
781
625
463
321
203
107
32
0
90
977
961
934
880
729
559
405
278
177
97
30
0
45
1255
1247
1216
1165
1005
804
597
413
261
138
41
0
90
1255
1235
1199
1131
937
720
522
358
228
124
38
0
45˚
1350
Candela
Zone
Lumens
%Lamp
%Fixt
0-30
0-40
0-60
0-90
0-180
904.40
1405.32
2240.16
2695.4
2695.4
N.A.
N.A.
N.A.
N.A.
N.A.
33.60
52.10
83.10
100.00
100.00
Total Luminaire Watts
Ballast Factor
CIE Type
Spacing Criteria (0-180)
Spacing Criteria (90-270)
Spacing Criteria (Diagonal)
Basic Luminous Shape
900
15˚
Lumens
Report#: P21072
30˚
22DR LED
S22DR-2L35-4D-S92HT
0˚
Zone
Total Luminaire Watts
Ballast Factor
CIE Type
Spacing Criteria (0-180)
Spacing Criteria (90-270)
Spacing Criteria (Diagonal)
Basic Luminous Shape
900
Candela
45
1.00
Direct
1.18
1.04
1.20
Rectangular
Angle
0
5
10
15
25
35
45
55
65
75
85
90
0
1255
1265
1242
1202
1075
895
688
485
306
157
45
0
Report#: P21069
30˚
Mounting Information
5"
ACCESS PLATE
5"
23 38 "
71 38 "
6FT IND
3FT IND
5"
ACCESS PLATE
4FT IND
ETG (15/16" Exposed T-Grid)
Mounting Details
3¼” Grid center to center
ACCESS PLATE
35 38 "
2FT IND
5"
5"
ACCESS PLATE
47 38 "
ACCESS PLATE
8FT IND
FTG ( 9/16" Fine T-Grid)
Mounting Details
3” Grid center to center
STG (9/16" Slot T-Grid)
Mounting Details
3” Grid center to center
SR (Sheetrock)
Mounting Details
25⁄8” Rough in wide opening
95 38 "
FSR (Flangeless Sheetrock)
Mounting Details
27⁄8” Rough in wide opening
Specifications and Dimensions subject to change without notice.
Neo-Ray • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801
ADN101862
09/19/2011 4:13:28 PM
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
LEUCOS USA #106004-WALL
SCONCE
Type:
R
Notes:
LDI12-6006
Leucos USA, INc.
11 Mayfield Ave.
Edison, New Jersey, 08837
www.leucosusa.com
Product name
DECO 50
Designer
LEUCOS DESIGN TEAM
Designed to mimic an abstract painting, this wall/ceiling design is available in three shapes. The decorative glass diffuser is offered in swirls
of amber or white on white pattern and in a bamboo inspired white on white pattern. An angled white metal backing completely shields the
incandescent or fluorescent light source. Decorative elements that secure the glass are provided in both clear acrylic balls or brushed nickel
buttons. ADA compliant when wall mounted.
Type
Light source
Dimensions
wall
ceiling
halogen
fluorescent
lb 11.79
ft³ 5.65
Light source
Code
Color
Structure
106004
White with
White Swirl
White
(1* )halogen (2* )fluorescent
Page 1/1
G9(1*)
2GX13
FC12T5(2*)
1x55 W
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
LEUCOS USA #106004-WALL
SCONCE
Type:
R
Notes:
LDI12-6006
CERTIFICATION
MARKS
Certifies that a product conforms to EN standards and has been designed and
manufactured by companies with an approved UNI EN ISO 9000 quality control
system. The ENEC symbol is issued by authorised boards to guarantee the safety and
quality of our products for the final customer.
Guarantees that the product has passed all the tests established for electrical safety
standards by the European Community.
The fixture can be applied on surfaces normally inflammable.
Fixture class Il. A fixture where protection against electric shock does not rely only on
the main insulation but also on further safety measures involving double insulation or
reinforced insulation.
Fixture class III - A fixture where protection against electric shock depends on the very
low and safe voltage supply, guaranteeing no higher voltage levels are generated. N.B.
a Class III fixture does not necessarily require grounding protection.
lndex protection. A symbol that identifies the protection index against dust,
solid particles or damp entering the fixture.
These bulb does not need shield.
Low-energy consumption bulbs fit (fluorescent).
The Americans Disabilities Act.
Italian Quality Mark - The IMQ mark certifies the conformity of electrical products to
the CEI and EN standards. IMQ is the Italian testing and certification. Board for safety
and quality of products and enterprise.
99
Notes:
Port Canaveral-Welcome Center-6006-REV
121812DS
L
E
Enclosed
U
C
O
S
One installer
Decò 30 - Decò 50
Decò 70
®
INSTALLATION INSTRUCTIONS - LEUCOS SUA
A1
Decò 30
Decò 50
Save instructions
Decò 70
Revised
11 Nov. 08
DISCONNECT POWER BEFORE INSTALLATION. - FIXTURE TO BE INSTALLED BY
A CERTIFIED ELECTRICIAN.- INSTALL IN ACCORDANCE WITH THE NATIONAL
AND LOCAL ELECTRICAL CODES. - TAKE GREAT CARE TO AVOID SCRATCHING
OR CHIPPING THE GLASS WHEN CARRYING OUT THE OPERATIONS BELOW
DECO’ 30: max 2x18W 120V or 277V G24-q2 quad
or max 6x40W 120V G9
or max 2x60W 120V G9
A
Decò 30
B
K
Halogen version
Decò 50
Decò 70
K
Halogen version
K
A
H
1. Fig.1. Remove reflector “B”(only for the halogen equipment).
Run supply wires from standard 4" octagon recessed junction box through center of
fixture "A" and mount fixture "A" to the wall or to the ceiling through slots "H"
H
2. Fasten fixture "A" to wall or to the ceiling through (4) holes "K".
3. Make the wire connection and guide the excess wire inside the J/Box.
4. Replace reflector “B” (only for the halogen equipment).
A
5. Install the bulbs into the respective sockets and make a working test.
For Fluorescent: be carefull to snap the tube inside the plastic lamp holder clips “Z”.
6. Remove knobs “V or W” from structure “A”, then place the diffuser “E” in order to
match the four holes withe the corresponding four threaded sites of each corner.
Re/screw the four knobs “V or W” and lock moderately the glass.
K
DO NOT USE TOOLS, use only fingers.
Halogen version
NOTE: Fig.2. In case of the thumb screws “V” please take care to place the plastic
washers “P” on the glass holes as shown in Fig.2.
DECO’ 50: max 1x55W 120V or 277V 2GX13 - FC12T5
or max 6x40W 120V G9
CIRCUIT DIAGRAM:
WHITE NEUTRAL
BLACK PHASE
GREEN-YELLOW
BARE COPPER WIRE
Ground
DECO’ 70: max 2x36W 120V or 277V 2G11
FOR U.S.A. MARKET ONLY
MOUNTS TO STANDARD IUNCTION BOX
For additional information please contact your local dealer or LEUCOS U.S.A. At:
Tel. (732) 225-0010 Fax (732) 225-0250 www.leucos.com - e-mail: info@leucosusa.com
H
B
B
V/W
E
E
Fig. 1
V/W
E
V/W
Fig. 1
P
K
V
W
H
K
Z
Fluorescent version
Z
Fluorescent version
Z
Fluorescent version
H
Fig. 2
K
Fig. 1
2x36W
R
Job Name:
Type:
Catalog Number:
LEUCOS USA #106004-WALL
SCONCE
Submitted by Lighting Dynamics, Inc.
LDI12-6006
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
TA/TB
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase)
Project: Port Canaveral Welcome Center
Substitution Request Number:
From:
To:
Lighting
Incorporated
Date:
GWWO Architects/ Henry Adams Cons. Engineers
11/30/12
A/E: Project Number:
Re:
Dynamics
Contract For:
Lighting Dynamics Inc.
1124
Port Canaveral Welcome Center
Specification Title: Substitution Procedures
Description: Substitutions
Section: 012500
Article/Paragraph:
Page: 18
1.1-1.4
Proposed/Substitution:
Manufacturer: HALO LIGHTING
Address:
Model #:
L805SML/SP-FL/830-MB/L1973-MB
MED
Installer:
Gerelco Electrical Contractors
History:
New product
Available upon request
Address: 560 NW Enterprise Drive, Port Saint Lucie,FL,34986 Phone: 772-340-7474
1-4 years old
5-10 years old
Differences between proposed substitution and specified product:
More than 10 years old
Product is comparable in performance, design & aesthetics
Point-by-point comparative data attached — REQUIRED BY A/E
Reason for not providing specified item: We don’t represent the specified manufacturer, we are providing a comparable product
In design, performance & aesthetics
Similar Installation: This product has been used on numerous projects in size and scope comparable to this project. Additional information is
available upon further request from Architect & Engineer.
Project:
Available upon request
Architect: Available upon request
Address:
Owner:
N/A
Date Installed: N/A
Proposed substitution affects other parts of Work:
No
Yes; explain
Savings to Owner for accepting substitution: Alternate Equal
Proposed substitution changes Contract Time:
Supporting Data Attached:
Drawings
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
No
Yes [Add]
Product Data
Samples
Page
of
($ 0
).
[Deduct]
days.
Tests
Reports
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
TA/TB
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase
— Continued)
The Undersigned certifies:
• Proposed substitution has been fully investigated and determined to be equal or superior in all respects to specified product.
• Same warranty will be furnished for proposed substitution as for specified product.
• Same maintenance service and source of replacement parts, as applicable, is available.
• Proposed substitution will have no adverse effect on other trades and will not affect or delay progress schedule.
• Cost data as stated above is complete. Claims for additional costs related to accepted substitution which may subsequently become
apparent are to be waived.
• Proposed substitution does not affect dimensions and functional clearances.
• Payment will be made for changes to building design, including A/E design, detailing, and construction costs caused by the substitution.
• Coordination, installation, and changes in the Work as necessary for accepted substitution will be complete in all respects.
Submitted by: Lighting Dynamics Inc.
Signed by:
Ryan Huff
Firm:
Lighting Dynamics Inc.
Address:
7835 W Commercial Blvd, Tamarac, FL, 33351
Telephone:
954-944-0286
Attachments:
A/E’s REVIEW AND RECOMMENDATION
Approve Substitution - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Approve Substitution as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Reject Substitution - Use specified materials.
Substitution Request received too late - Use specified materials.
Signed by:
Date:
OWNER'S REVIEW AND ACTION
Substitution approved - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare Change
Order.
Substitution approved as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare
Change Order.
Substitution rejected - Use specified materials.
Signed by:
Additional Comments:
Other:
Date:
Contractor
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
Subcontractor
Page
Supplier
of
Manufacturer
A/E
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
L805-MED-NF830MB/L1973-MB
Type:
TA
Notes:
LDI12-6006
HALO
®
DESCRIPTION
A series of understated, balanced luminaires that come in a variety of lamp
types. The Stasis family features die-cast and extruded bodies with elegant
free-flowing lines. Ideal for accent and display lighting applications. This
Stasis LED is perfect for those applications where performance is required
from a discrete source.
Type
Catalog #
Project
Date
Comments
Prepared by
SPECIFICATION FEATURES
Quick-Lock Adapter
Attaches electrically and
mechanically anywhere along
track. Includes discrete locking tab
that locks luminaire on track and
allows for easy removal and
repositioning.
Lockable Aiming
Lampholder tilt and rotation can be
locked in place easily with a 0.5mm
allen wrench (included).
Switch
On/off switch allows power to be
turned off during lamp
replacement on individual
luminaires.
Luminaire Arm
Arm allows the lamp housing tilt to
adjust +/-90°. It also pivots +/-90°
around the ballast housing. This
enables the ballast housing to
remain static on the track creating
a clean look, while providing full
aiming capabilities. The arm
employs graduations every 15° for
precise and repeatable tilt aiming.
Indicator mark on the bottom
ensures perfect luminaire housing
alignment with track.
LED Light Engine
Equipped with (7) 3-Watt white
LEDs. Factory configurable optics
allow for 3 optical distributions.
High CRI of 85 with excellent color
consistency of +/-50°K color
temperature.
Driver Housing
Die-cast and extruded aluminum
housing incorporates the lamp
control circuit.
Heat Sink
Aluminum die-cast heat sink
provides exceptional thermal
management to yield 70% lumen
maintenance after 50,000 hours of
operation.
Dimming
The Stasis LED MED is dimmable
to 15% with electronic low voltage
equipment (ELV dimmers need a
neutral connection in the wall box).
Recommended ELV Dimmers:
LUTRON:
Diva: DVELV Series
Maestro: MAELV Series
Nova: NTELV Series
Skylark: SELV Series
LEVITRON:
Acenti: ACE Series
Illumatech: IPE Series
L805MED
Stasis
Labels
UL/cUL listed for use with Halo
Architectural Power-Trac and Lazer
Track. UL/cUL classified for Juno
[See Footnote #1 in Ordering
Information below], Lightolier [See
Footnote #2 below], and Global
[See Footnote #3 below] TEK/HTEK
Track.
18W
Medium
3000K
CBCP
Spot 8˚
36079
Narrow Flood 25˚
3044
Flood 40˚
1736
4000K Multiplier= 1.25
5-5/8"
[143mm]
6-1/4"
[159mm]
2-3/8"
[60mm]
4-3/16"
[106mm]
Lighting Data
3000K Spot
Lumens:
Lumens per watt:
Watts at 120VAC
Energy Data:
Input Power:
Power Factor:
Input Current:
774
41.7
18.6
18W
>0.92
0.16 Amps
ORDERING INFORMATION
805
Track
L=Halo Power Track
LA=Halo
Architectural Track
LF=Flexible Track
LJ=Juno Track 1
LL=Lightolier Track 2
3
L2G=Global TEK or HTEK
MED
Stasis LED
805
Beam
SP=Spot 8˚
NF=Narrow
Flood 25˚
FL=Flood 40˚
Size
MED=Medium 18W
CRI
8=85
CCT
30=3000K
40=4000K
Finish
AH =Aluminum Haze
P =White (L and LA only)
MB =Black (L and LA only)
Voltage
Blank=120V
277=277V
(only with LA
or HTEK)
Notes:
1 Juno® T single circuit and 2-circuit track contact. Juno is a registered trademark of Juno Lighting.
2 Lightolier ® Lyfespan 6000 single circuit and 2 circuit track contact. Lightolier is a registered trademark of Philips Lighting.
3 Global ® is a registered trademark of Nordic Aluminum.
Specifications and Dimensions subject to change without notice.
Consult your representative for additional options and finishes.
ADV091696
07/06/2011 10:23:50 AM
Catalog Number:
L805-MED-NF830MB/L1973-MB
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
TA
Notes:
LDI12-6006
.ACCESSORIES
L805MED
Media Holder – Accepts up to 2 pieces of media
LM10530=Media Holder
3 15/16”
[100mm]
3 1/2”
[89mm]
4 1/2”
[114mm]
1 1/4”
[32mm]
Media Holder
L411=Medium Pink Color Filter
L412=Warm Red Color Filter
L420=Daylight Blue Color Filter
L421=Medium Blue Color Filter
L431=Medium Amber Color Filter
L441=Medium Green Color Filter
L450=Solite
L400 Series Color Filters
Glass Filters 3-3/4" (96mm)
diameter. For use with L1830
and L252 Media Holder.
3 3/4"
[96mm]
1/4"
[6mm]
L400 Color
Filters
Color Temp.= 3000K
4000K Multiplier= 1.25
Spot: 8˚
CBCP: 36079
Lumens: 774
LPW: 42
Narrow Flood: 25˚
CBCP: 3044
Lumens: 726
LPW: 41
Flood: 40˚
CBCP: 1736
Lumens: 725
LPW: 38
0° Aiming Angle
Horizontal Footcandles
D
5.0
7.5
10.0
12.5
15.0
30° Aiming Angle
Horizontal Footcandles
30° Aiming Angle
Vertical Footcandles on Wall
60° Aiming Angle
Vertical Footcandles on Wall
FC
1443
641
361
231
160
L
0.6
0.9
1.2
1.5
1.8
W
0.6
0.9
1.2
1.5
1.8
D
5.0
7.5
10.0
12.5
15.0
FC
937
417
234
150
104
L
0.9
1.3
1.7
2.2
2.6
W
0.7
1.1
1.4
1.8
2.1
CB
2.9
4.3
5.8
7.2
8.7
D
3.0
4.0
5.0
6.0
FC
552
311
199
138
L
1.5
2.0
2.6
3.1
W
0.8
1.1
1.4
1.7
CB
5.2
6.9
8.7
10.4
D
FC
L
3.0 1417 0.9
4.0 797 1.2
5.0 510 1.5
6.0 354 1.8
W
0.6
0.8
0.9
1.1
CB
3.0
4.0
5.0
6.0
D
FC
5.0 122
7.5 54
10.0 30
12.5 19
15.0 14
L
2.3
3.4
4.6
5.7
6.8
W
2.3
3.4
4.6
5.7
6.8
D
FC
5.0 85
7.5 38
10.0 21
12.5 14
15.0 9
L
2.8
4.2
5.6
7.0
8.4
W
2.5
3.7
5.0
6.2
7.5
CB
2.9
4.3
5.8
7.2
8.7
D
3.0
4.0
5.0
6.0
FC
64
36
23
16
L
3.2
4.3
5.4
6.5
W
2.2
2.9
3.6
4.3
CB
5.2
6.9
8.7
10.4
D
3.0
4.0
5.0
6.0
FC
144
81
52
36
L
2.2
2.9
3.7
4.4
W
1.7
2.3
2.9
3.4
CB
3.0
4.0
5.0
6.0
D
5.0
7.5
10.0
12.5
15.0
L
3.5
5.2
6.9
8.7
10.4
W
3.5
5.2
6.9
8.7
10.4
D
FC
5.0 56
7.5 25
10.0 14
12.5 9
15.0 6
L
3.7
5.5
7.4
9.2
11.1
W
3.6
5.4
7.1
8.9
10.7
CB
2.9
4.3
5.8
7.2
8.7
D
3.0
4.0
5.0
6.0
FC
56
31
20
14
L
2.7
3.7
4.6
5.5
W
2.7
3.6
4.5
5.4
CB
5.2
6.9
8.7
10.4
D
3.0
4.0
5.0
6.0
FC
105
59
38
26
L
2.3
3.1
3.9
4.7
W
2.3
3.1
3.9
4.7
CB
3.0
4.0
5.0
6.0
FC
69
31
17
11
8
Notes and Definitions:
Beam spread is to 50% center beam candlepower (CBCP.)
D=Distance in feet to floor or wall.
FC=Footcandles on floor or wall at center beam aiming location.
L =Effective Visual Beam length in feet (50% of maximum footcandle level.)
W=Effective Visual Beam width in feet (50% of maximum footcandle level.)
CB=Distance in feet across or down to center beam location.
Note: Specifications and Dimensions subject to change without notice.
Visit our web site at www.cooperlighting.com
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770 486.4801
Cooper Lighting 5925 McLaughlin Rd. Mississauga, Ontario, Canada L5R 1B8 905.507.4000 FAX 905.568.7049
Specifications and Dimensions subject to change without notice.
HALO Track • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801
ADV091696
07/06/2011 10:23:50 AM
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
L805-MED-NF830MB/L1973-MB
Notes:
Type:
TA
LDI12-6006
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
RAZ24
Type:
UC
Notes:
LDI12-6006
Catalog Number
Notes
Type
Indoor General Purpose
FEATURES & SPECIFICATIONS
INTENDED USE
Provides task or accent lighting in commercial, retail, hospitality and residential
applications. Ideal for use under and over cabinets, display cases, task lighting,
office lighting, coves and utility/work areas.
Rayzer
TM
Modular LED
Lighting System
ATTRIBUTES
Durable aluminum construction in a low-profile design. Can be plugged in or
direct-wired (splice box and 24” connector cord required for direct-wiring).
Link up to 10’ of modular system to one transformer (sold separately). Fixtures
can be linked end-to-end with the end row connector (sold separately). All
fixtures include a 18” linking cord. 3”, 24” and 121” connector cords may also be
purchased separately.
LEDs have a 50,000 hour L70 rated life. Provides warm color temperature, 3,000K
with CRI 85, and even illumination.
Dimmable when used with the optional step dimmer.
All mounting hardware included. Mounting clips allow for quick & easy installation
flush or at 30º. All configurations tested to IES LM79 standards.
LISTING
CUL listed to US and Canadian safety standards. ENERGY STAR® qualified.
WARRANTY
Guaranteed for three years against mechanical defects in manufacture.
DIMENSIONS
All dimensions are in inches (centimeters)
Nominal
Size
Model
No.
Number
of Lamps
(A) Length
Inches (cm)
(B) Width
Inches (cm)
(C) Height
Inches (cm)
9”
RAZ9
3
9-1/4” (23.49)
1-1/4” (3.18)
1/2” (1.27)
12”
RAZ12
4
12-1/4” (31.11)
1-1/4” (3.18)
1/2” (1.27)
18”
RAZ18
6
18-1/4” (46.35)
1-1/4” (3.18)
1/2” (1.27)
24”
RAZ24
8
24-1/4” (46.35)
1-1/4” (3.18)
1/2” (1.27)
ORDERING INFORMATION
B
A
C
Example: RAZ18
Choose the boldface catalog nomenclature that best suits your needs and write it on the appropriate line.
Order accessories as separate catalog numbers.
Accessories/Replacement Parts
Model Number
RAZ9 9” length - 3 LEDs
RAZ12 12” length - 4 LEDs
RAZ18 18” length - 6 LEDs
RAZ24 24” length - 8 LEDs
Options
(Consult factory)
Indoor General Purpose - LED Modular Lighting System
RAZTRANS24 120
RAZTRANS24 MVOLT
RAZDIM
RAZ CC121
RAZ CC24
RAZ CC3
RAZLVCC
RAZ ERC
RAZ PHD
RAZ INLS26
UCD JB
UCD JB BL
UC ERC24 R12
UC ERC24 BL
24v transformer - 120v power source
24v transformer - Multi-Volt power source
Step dimmer with remote touch pad
121” Linking cord (fixture to fixture)
24” linking cord (fixture to fixture)
3” linking cord (fixture to fixture)
Low voltage linking cord (cord to cord)
End row connector
Power hub distributor
In-line power switch
Splice box - white (required for direct wire)
Splice box - black (required for direct wire)
24” connector cord - white (required for direct wire)
24” connector cord - black (required for direct wire)
Sheet #: RAZC
DEC-624
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
RAZ24
Type:
UC
Notes:
LDI12-6006
Rayzer™ LED Modular Lighting System
PHOTOMETRICS
Full photometric data report available within 2 weeks from request. Consult factory.
9”
12”
18”
24”
INSTALLATION DIAGRAM
Note: Fixture includes 18” linking cord, mounting clips
for flush or 30º mounting, and screws.
Lithonia Lighting
Sheet #: RAZC
©2010 Acuity Brands Lighting, Inc. All rights reserved. Rev. 4/10
Consumer Products Group
One Lithonia Way, Conyers, GA 30012
Phone: 800-748-5070 Fax: 770-860-3903
In Canada: 160 Avenue Labrosse, Point-Claire, P.Q., H9R 1A1
www.lightahome.com
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
UC/UCD
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase)
Project: Port Canaveral Welcome Center
Substitution Request Number:
From:
To:
Lighting
Incorporated
Date:
GWWO Architects/ Henry Adams Cons. Engineers
11/30/12
A/E: Project Number:
Re:
Dynamics
Contract For:
Lighting Dynamics Inc.
1124
Port Canaveral Welcome Center
Specification Title: Substitution Procedures
Description: Substitutions
Section: 012500
Article/Paragraph:
Page: 18
1.1-1.4
Proposed/Substitution:
Manufacturer:
COOPER
LIGHTING
TERON
LIGHTING
Model #:
12313-NI
Installer:
Gerelco Electrical Contractors
History:
New product
Address:
Available upon request
Address: 560 NW Enterprise Drive, Port Saint Lucie,FL,34986 Phone: 772-340-7474
1-4 years old
5-10 years old
Differences between proposed substitution and specified product:
More than 10 years old
Product is comparable in performance, design & aesthetics
Point-by-point comparative data attached — REQUIRED BY A/E
Reason for not providing specified item: We don’t represent the specified manufacturer, we are providing a comparable product
In design, performance & aesthetics
Similar Installation: This product has been used on numerous projects in size and scope comparable to this project. Additional information is
available upon further request from Architect & Engineer.
Project:
Available upon request
Architect: Available upon request
Address:
Owner:
N/A
Date Installed: N/A
Proposed substitution affects other parts of Work:
No
Yes; explain
Savings to Owner for accepting substitution: Alternate Equal
Proposed substitution changes Contract Time:
Supporting Data Attached:
Drawings
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
No
Yes [Add]
Product Data
Samples
Page
of
($ 0
).
[Deduct]
days.
Tests
Reports
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
SUBSTITUTION FORM
Type:
UC/UCD
Notes:
LDI12-6006
SUBSTITUTION
REQUEST
(After the Bidding/Negotiating Phase
— Continued)
The Undersigned certifies:
• Proposed substitution has been fully investigated and determined to be equal or superior in all respects to specified product.
• Same warranty will be furnished for proposed substitution as for specified product.
• Same maintenance service and source of replacement parts, as applicable, is available.
• Proposed substitution will have no adverse effect on other trades and will not affect or delay progress schedule.
• Cost data as stated above is complete. Claims for additional costs related to accepted substitution which may subsequently become
apparent are to be waived.
• Proposed substitution does not affect dimensions and functional clearances.
• Payment will be made for changes to building design, including A/E design, detailing, and construction costs caused by the substitution.
• Coordination, installation, and changes in the Work as necessary for accepted substitution will be complete in all respects.
Submitted by: Lighting Dynamics Inc.
Signed by:
Ryan Huff
Firm:
Lighting Dynamics Inc.
Address:
7835 W Commercial Blvd, Tamarac, FL, 33351
Telephone:
954-944-0286
Attachments:
A/E’s REVIEW AND RECOMMENDATION
Approve Substitution - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Approve Substitution as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures.
Reject Substitution - Use specified materials.
Substitution Request received too late - Use specified materials.
Signed by:
Date:
OWNER'S REVIEW AND ACTION
Substitution approved - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare Change
Order.
Substitution approved as noted - Make submittals in accordance with Specification Section 01 25 00 Substitution Procedures. Prepare
Change Order.
Substitution rejected - Use specified materials.
Signed by:
Additional Comments:
Other:
Date:
Contractor
© Copyright 2010, Construction Specifications Institute,
110 South Union St., Suite 100, Alexandria, VA 22314
Subcontractor
Page
Supplier
of
Manufacturer
A/E
Form Version: November 2010
CSI Form 13.1A
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Catalog Number:
HU1024D830P/HU107P/HU106P
Notes: LENGTHS/FINISH & ACCESSORIES
PER PLANS
Type:
UC/UCD
LDI12-6006
HALO
®
DES C R I P T I ON
Ideal for task, accent, office, cove, utility, under and above cabinet lighting
display, the Halo Undercabinet low-profile design delivers maximum
energy savings and life with easy installation. The integrated driver
allowing 120V direct to the fixture for easy installation. Fixtures are
available in 12”, 18” or 24” lengths, the Halo system can be configured
to fit almost anywhere. Smooth dimming down to 15% using a standard
dimmer*. Connector cables in a variety of different lengths make it easy
to link one unit to another. Each unit has an integrated on-off switch.
Type
Catalog #
Project
Date
Comments
Prepared by
SPECI FI C A T I ON FE AT UR E S
Even Light Distribution
Finish Options
Direct Wire Accessory
Utilizing tightly clustered
proximity phosphor LEDs, results
in consistent illumination with
very high efficiency. Mounting the
LEDs very close to the lens surface
creates a very wide distribution
and limits shadows for high cutoff
angles.
Fixtures and accessories are
available in both White (P) and
Matte Black (MB) finishes.
Available direct wire splice box
has a connection port on each
side to allow for runs in either or
both directions. Various connector
cable options provide flexibility
of mounting location. Includes
Romex/ 1/2 conduit connector.
Low Profile Housing
Heavy gauge aluminum housing
and color matched end caps with
less than 3/4” overall height.
Two Fastener Mounting
Each unit is secured directly to the
mounting surface with just two
fasteners keeping installation costs
low. Can be mounted in horizontal
and vertical orientations.
Electronic Ballast
Electronic driver provides
full light output and rated ife.
Provides flicker free and noise free
operation.
HU10P
Continuous Runs
Link any combination of fixtures
up to 800 W total load using
available connectors.
Labels
- cULus listed
- Can be used to meet IECC, ASHRAE commercial and residential standards
- ENERGY STAR® qualified
-FCC
HU10MB
“L”
See Size Table
HU10
Integrated Driver
LED Undercabinet
E NE RGY D A TA
Size Description
12 in. Nominal
18 in. Nominal
24 in. Nominal
Length “L”
12.38” [314.5mm]
18.38” [466.9mm]
24.38” [619.3mm]
Power Factor: >0.99
THD: <10%
Color Temperature: 3000 K
Color Rendering Index: 80
Nominal Lumens/Ft: 350
12” Fixture
Lumens: 341
120V Input Watts: 4.95
Line Amps: 0.044
LPW: 70
.68”
[17.296mm]
.38”
[9.525mm]
when installed
3.24”
[82.35mm]
18” Fixture
Lumens: 563
120V Input Watts: 8.17
Line Amps: 0.072
LPW: 69
24” Fixture
Lumens: 707
120V Input Watts: 9.61
Line Amps: 0.084
LPW: 74
OR D E R I NG I NFOR MAT I ON
SAMPLE NUMBER: HU1012D830P (12” Dimmable Fixture, 80 CRI, 3000 K, White Finish)
Family
Length
Dimming
Lens
CRI
Color Temperature
Finish
Accessories
HU10 =Halo Integrated Driver
Undercabinet
12=12”
18=18”
24=24”
D=Dimmable*
[Blank]=Clear
8=80 CRI
30=3000K
P=White
MB=Matte
Black
HU101=3” Daisy Chain Connector
HU102=6” Daisy Chain Connector
HU103=24” Daisy Chain Connector
HU104=120” Daisy Chain Connector
HU105=48” Power Cord
HU106=Splice Box
HU107=1-1/2” Male-to-Male Connector
*See our website for dimmer compatibility guide - www.cooperlighting.com
ADV121541
www.cooperlighting.com
October 31, 2012 4:16 PM
Catalog Number:
HU1024D830P/HU107P/HU106P
Submitted by Lighting Dynamics, Inc.
Job Name:
Port Canaveral-Welcome Center-6006-REV
121812DS
Type:
UC/UCD
Notes: LENGTHS/FINISH & ACCESSORIES
PER PLANS
LDI12-6006
H U 10
C ONNEC TO R S
HU101
HU102
HU103
HU104
HU105
3” Daisy Chain Connector
6” Daisy Chain Connector
24” Daisy Chain Connector
120” Daisy Chain Connector
48” Power Cord
Finish: P = White; MB = Matte Black Example: HU101P = 3” Daisy Chain Connector, White
PHOTOM ET R Y
Optional Mounting Heights
Fixture Application Illustration
MOUNTING HEIGHT 15"
MOUNTING HEIGHT 18"
Top Number
Report: HU1012D830.IES
Middle Number
Report: HU1018D830.IES
Bottom Number
Report: HU1024D830.IES
Countertop 16" x 30"
Top Number Report - HU1012D830.IES
Middle Number Report - HU1018D830.IES
Bottom Number Report - HU1024D830.IES
3.6 6.4
11.9 19.5 26.9 29.4 26.9 19.5 11.7
6.3
3.6
2.5 4.3
1.5 2.6
7.9
4.9
7.9
4.9
4.3
2.6
2.5
1.5
4.8 9.1
18.8 37.2 55.4 60.2 55.4 36.6 18.6
9.0
4.7
3.2 5.8
1.9 3.5
11.5 23.8 46.7 63.2 46.7 23.7 11.5
7.0 14.5 28.6 38.6 28.6 14.5 7.0
5.8
3.5
3.2
1.9
128 73.3 29.4 12.1
5.7
5.7 12.1 29.6 73.7 128
3.7 7.0
2.2 4.3
2 in.
16 in.
18 in.
1-1/2 in.
6 in.
4.6
12 in.
3.2
4.6
18 in.
1.9
4
7.3
8.1
14.3
24 in.
2.5
4.6
7.3
7.3
10 14.3
14.4
30 in.
2.9
22.7
4.5
6.1 13.9
4.7
8.9
6.2
16.9
30.4
14.9
2.9
30.9
5.5
4.1
8.4
10.4 22.7
0.3
25.9
9.1
18.5
33.1
26.7
2.5
12
0.2
30.4
5.6
16
62.4
32.7
30.8
11.3
16.2
0.1
7.6
30.4
45.8
40.9
0.3
19.3 24.1
18.9 33.1
4.6
30 in.
25.9
96
28.1
0.2
24.8 68.3
22.7
11.7 15.4
57.5
16 30.4
81.6
43.7
0.1
16.9
35.1
14.3
0.3
9.2
104
49.6
106
26.3
45.4
45.8
24 in.
10.4 22.7
10
0.2
111
8.1
90.5
31.7
28.1
96
0.1
6.1
26.7
67.1 116
5.5
54.8
19.1 0.3
81.6
66.5
14.3
16.3 62.9
18in.
3.4
0.2
49.6
124
57.8
13.9
106
8.1
0.1
73.2
40.9
0.3
75
35
8.4
90.5
7.3
31
24.8
74.7
0.2
12 in.
6
68
54.8
4.5
18.5
66.5
45
0.1
0.3
4
14.5
43.7
11.3
57.8
0.2
2.5
8.9
26.3
6 in.
32.6
35 0.3
7.3
0.1
45.4
5.5
19.3
4.6
31.7
14.9
0.2
11.7
2.9
23.9
19.1 0.3
0 in.
9.1
0.2
15.4
5.6
7.3
0.2
CL
9.3
4.7
11.9
0.1
6 in.
0.3
2.9
7.6
0.3
4.6
6.2
0.2
0.2
12 in.
4.1
0.2
2.5
0.1
0.3
Point By Point Illumination Scale is
18 in.
0.2
Exaggerated on Fixture Application
0.1
24 in.
and Mounting.
8.1
5.5
3.4
4.6
3.2
1.9
30 in.
14.2 23.2 28.4 23.2 14.2
8.7 14.4 17.8 14.4 8.7
132
15.7 40.3 102 162 102 40.3 15.7
9.6 24.6 62.1 97.3 62.1 24.6 9.6
7.0
4.3
3.7
2.2
149 83.8 31.6 12.4
5.7
5.7 12.4 31.6 83.5 149
154
3.6 7.1
2.2 4.4
16.4 44.3 120
10.0 26.7 72.0
193 120 44.3 16.4
116 72.0 26.7 10.0
7.1
4.4
3.6
2.2
4.6 9.4
21.3 46.4 75.2 81.1 75.2 47.0 21.5
9.5
4.6
3.0 5.8
1.8 3.5
12.4 29.3 64.0 90.9 64.0 29.3 12.4
7.5 17.7 38.7 54.9 38.7 17.7 7.5
5.8
3.5
3.0
1.8
0.3 0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.2 0.2
0.1 0.1
0.2
0.2
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
30" 24" 18" 12" 6"
0
1 -1 /2 "
6"
12"
18"
24"
30"
6" 12" 18" 24" 30"
CL
MOUNTING HEIGHT 24"
Top Number: Report - HU1012D830.IES
Middle Number: Report - HU1018D830.IES
Bottom Number: Report - HU1024D830.IES
6.6 10.6 16.9 24.0 29.9 32.2 29.9 24.0 16.9 10.6
6.6
4.7 7.6
2.8 4.6
7.6
4.6
4.7
2.8
8.3 13.8 22.7 33.5 43.3 46.8 43.3 33.5 22.6 13.8
8.2
5.8 9.8
3.5 5.9
9.7
5.9
5.8
3.5
9.7 16.7 28.5 44.8 59.5 65.1 59.5 44.8 28.5 16.7
9.6
6.6 11.4 20.1 34.2 51.5 60.2 51.5 34.2 20.1 11.4
4.0 6.9 12.1 20.7 31.3 36.6 31.3 20.7 12.1 6.9
6.6
4.0
9.8 17.0 29.4 46.9 62.4 68.7 62.4 46.9 29.4 17.0
9.8
6.7 11.6 20.5 35.7 54.5 63.6 54.5 35.7 20.5 11.6
4.1 7.0 12.4 21.5 33.0 38.1 33.0 21.5 12.4 7.0
6.7
4.1
8.7 14.5 24.1 37.0 48.4 52.8 48.4 37.0 24.1 14.5
8.6
6.0 10.2 17.3 28.6 41.7 48.3 41.7 28.6 17.3 10.2
3.7 6.1 10.5 17.3 25.3 29.2 25.3 17.3 10.5 6.1
6.0
3.7
0.3 0.2
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.3
0.2 0.2
0.1 0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
0.2
0.1
12.6 18.7 25.3 28.3 25.3 18.7 12.6
7.7 11.5 15.5 17.3 15.5 11.5 7.7
16.3 26.2 36.8 42.0 36.8 26.2 16.3
9.9 15.8 22.3 25.5 22.3 15.8 9.9
30" 24" 18" 12" 6"
0
1 -1 /2 "
6"
12"
18"
24"
30"
6" 12" 18" 24" 30"
CL
www.cooperlighting.com
Note: Specifications and Dimensions subject to change without notice.
Visit our web site at www.cooperlighting.com
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770 486.4801
Cooper Lighting 5925 McLaughlin Rd. Mississauga, Ontario, Canada L5R 1B8 905.507.4000 FAX 905.568.7049