APPROVED 06/May/2015 14:05:39 GMT
8
ITEM
D
7
DESCRIPTION
6
5
3
AIR INLET (SUCTION) CONNECTION
10"-125LBS R.F. FLANGE
A2
AIR OUTLET (DISCHARGE) CONNECTION
10"-125LBS R.F. FLANGE
B
OIL FILTER
C
AIR BREATHER
D
OIL DRAIN (PLUGGED)
E
OIL LEVEL GAUGE
F1
WATER INLET
0.75" NPT
F2
WATER OUTLET
0.75" NPT
G1
CYLINDER DRAIN
0.75" NPT
G2
CYLINDER DRAIN
0.75" NPT
ZONE
-
7.38
LUBRICATOR
A1
OIL FILTER
7.69
F1
12.56
19.50
WATER INLET
BARE
2
MOTOR
330
3
BARE PLATE
650
4
CONTROL PANEL
225
5
MISC
100
6
COMPRESSOR SHEAVE
50
7
TOTAL
3895
ECN
A
982011
DESCRIPTION
ORIGINAL RELEASE
DATE
DRAWN
APP'D
02MAY2015
PRS
KDV
D
19.47
14.00
CYL. &
COMPR.
WATER OUTLET
F2
REV
MOTOR &
SLIDE BASE
B
-
WEIGHT
(KG)
2540
1
76.20
9.03
0.50" NPT
DESCRIPTION
2
REVISIONS
SIZE / LEGEND
A1
SR.
NO.
1
4
SLIDE &
BASE
2.00
11.00
16.00
32.00
37.50
18.00
4.33
0.75" NPT CONNS. IN BOTTOM
OF CYL.(DRAINS)
G1 G2
17.75
69.55
TO END OF COMPR.
CRANKSHAFT
24.75
SPACE REQ'D
TO REMOVE
PISTON & ROD
(MIN.)
C
A2
22.31
42.41
38.59
38.96
C
TWO(2) CYL. LUBRICATOR
CONNS. ON CENTERLINE
OF CYL. (TOP & BOTTOM)
ROTATION
BELT GUARD
MOTOR
SHEAVE
AIR BREATHER
PANEL
C
.75" NPT WATER INLET
(CYLINDER JACKET WATER
HEATER MOUNTED INLINE)
13.00
22.75
12.63
E
29.91
D
0.50
FOR SIMS
B
5.91
B
FLOOR LINE
1.25
GROUT
3.5575
A1
A2
AIR DISCH. CONN.(NEAR SIDE)
AIR INLET CONN. (FAR SIDE)
INLET & DISCH. CAN BE REVERSED BY
REVERSING THE LOCATION OF THE INLET
& DISCH. VALVES. (SEE NOTES)
30.00
BACK VIEW
4.25
29.50
144.00
38.00
SCALE 0.100
A
MOTOR POWER : 50 HP
MOTOR SPEED : 1770 RPM
FRAME SIZE
: HX + 225SMC4
STANDARD TOLERANCES
ALL DIMENSIONS ARE IN
MILLIMETERS
[INCHES (IF SHOWN)]
V BELT DETAILS
QTY.
OF BELT
SIZE
OF BELT
OD DIA OF
MOTOR PULLEY
OD DIA OF
COMP.SHEAVE
COMP. SPPED
4
5VX-140
7.5"
29.3"
450
CENTER
DISTANCE
38.59
UNSPECIFIED TOLERANCES:
WHOLE
ONE PLACE (.X)
TWO PLACE (.XX)
ANGLES (.X)
:
:
:
:
1
0.5
0.25
1
Ingersoll-Rand Industrial Technologies
WARNING: THE EXPORT OR REEXPORT OF THIS DRAWING OR A PRODUCT PRODUCED
BY THIS DRAWING IS SUBJECT TO U.S. EXPORT ADMINISTRATION REGULATIONS
AND OTHER APPLICABLE GOVERNMENT RESTRICTIONS OR REGULATIONS.
PROPRIETARY NOTICE
DO NOT SCALE DRAWING
DRAWING CONFORMS TO
ASME Y14.5M - 1994
CAD GENERATED DRAWING,
NO MANUAL REVISIONS ALLOWED
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET
INFORMATION, IS THE PROPERTY OF INGERSOLL-RAND CO., AND IS
GIVEN TO THE RECEIVER IN CONFIDENCE. THE RECEIVER BY RECEPTION
AND RETENTION OF THE DRAWING ACCEPTS THE DRAWING IN CONFIDENCE
UNLESS OTHERWISE SPECIFIED:
AND AGREES THAT, EXCEPT AS AUTHORIZED IN WRITING BY
- REMOVE ALL BURRS AND SHARP CORNERS
INGERSOLL-RAND CO. IT WILL (1) NOT USE THE DRAWING OR ANY COPY
- WELD SYMBOLS TO BE IN ACCORDANCE
THEREOF OR THE CONFIDENTIAL OR TRADE SECRET INFORMATION
WITH ANSI/AWS A2.4
THEREIN; (2) NOT COPY THE DRAWING; (3) NOT DISCLOSE TO OTHERS
EITHER THE DRAWING OR THE CONFIDENTIAL OR TRADE SECRET
COPYRIGHT @ 2015
INFORMATION THEREIN; AND (4) UPON COMPLETION OF THE NEED TO
RETAIN THE DRAWING, OR UPON DEMAND, RETURN THE DRAWING, ALL
Ingersoll Rand
COPIES THEREOF, AND ALL MATERIAL COPIED THEREFROM.
ALL RIGHTS RESERVED
A
THIRD ANGLE PROJECTION
DRAWN
PRS
DATE
CHECKED
KDV
DATE
NAME
02MAY2015
APPROVED
MKR
R
02MAY2015
DATE
02MAY2015
DRAWING TYPE
Detail Drawing
NOMENCLATURE
SIZE
A1
SCALE
ARRANGEMENT, 22
X 7 ESH-VP
47534468
0.0 pound
ESTIMATED WEIGHT
(KG UNLESS OTHERWISE SPECIFIED)
47534468
0.20
MODEL
DWG NO.
PART NO.
IN
SHEET
ARRANGEMENT, 22 X 7 ESH-VP
REVISION
A
1 OF 2
For Internal Use:Model=47534468|ASSEM|A.0|Pankaj Sorathiya|05-May-15 03:40:50 PM|Open<>Drawing=47534468|DRAW|A.0|Pankaj Sorathiya|05-May-15 03:35:20 PM|Open
8
7
6
5
4
UNLESS OTHERWISE SPECIFIED PRINTED DOCUMENT IS UNCONTROLLED
3
2
1
A.0
APPROVED 06/May/2015 14:05:39 GMT
8
7
6
5
4
3
2
1
PRIMARY FORCE OR MOMENT
VERTICAL FORCE
Y
HORIZONTAL
MOMENT
X
Z
VERTICAL
MOMENT
CENTER OF
SHAFT
D
CRANKSHAFT REVOLUTION
D
SECONDARY FORCE OR MOMENT
X
Z
AXIS OF
CRANCKSHAFT
Y
HORIZONTAL
FORCES
CRANKSHAFT REVOLUTION
UNBALANCED INERCIA FORCES ON FOUNDATION:
THE FOUNDATION MUST BE DESIGN TO RESIST THE FOLLOWING FORCES.
MAXIMUM HORIZONTAL PRIMARY FORCES
1688 LBS
MAXIMUM HORIZONTAL SECONDARY FORCES
760 LBS
MAXIMUM VERTICAL PRIMARY FORCES
1342 LBS
MAXIMUM VERTICAL SECONDARY FORCES
0 LBS
MAXIMUM HORIZONTAL PRIMARY MOMENT (ABOUT AXIS Y-Y)
1306 LBS. FT.
MAXIMUM HORIZONTAL SECONDARY MOMENT (ABOUT AXIS Y-Y)
1306 LBS. FT.
MAXIMUM VERTICAL PRIMARY MOMENT (ABOUT AXIS X-X)
0 LBS. FT.
MAXIMUM VERTICAL SECONDARY MOMENT (ABOUT AXIS X-X)
0 LBS. FT.
NOTES:
1) MOMENTS TAKEN ABOUT AXIS THROUGH CENTER OF SHAFT FORCES TAKEN AS ACTING AT
CENTER OF SHAFT.
C
C
2) PRIMARY FORCES AND MOMENT CHANGE FROM ZERO TO MAXIMUM GIVEN ABOVE TO ZERO
TO SAME MAXIMUM IN REVERSE DIRECTION AND BACK TO ZERO ONCE IN
A CRANKSHAFT REVOLUTION SECONDARY FORCES AND MOMENTS GO THROUGH
THIS CYCLE TWICE IN A REVOLUTION. THE SKETCH SHOWS THIS.
3) CUSTOMER TO SUPPORT ALL PIPING AS CLOSE AS POSIBLE BEYOND THE BATTERY LIMITS
SUCH THAT FORCES & MOMENTS DUE TO EXPANSION OR CONTRACTION OR WEIGHTS
INTRODUCED AT THE BATTERY LIMITS ARE MINIMUM.
NOTES:
1. DO NOT SCALE THIS DRAWING, USE FIGURES GIVEN.
2. THE FOUNDATION SHOWN IS MIN., SUITABLE ONLY FOR FIRM SOIL BACKED UP BY BEDROCK. WE
RECOMMEND THAT YOU INVESTIGATE THE SOIL CONDITION IN THE PROSPECTIVE LOCATION AND IF
THERE IS ANY DOUBT ABOUT ITS SUITABILITY, WE URGE CONSULTATION WITH A FOUNDATION EXPERT.
3. SEE GENERAL FOUNDATION INSTRUCTION FORM AP 0250-C.
4. FOR GROYTING INSTRUCTIONS SEE 14002D1D.
5 BE SURE TO READ THE INSTRUCTION BOOK BEFORE CONSTRUCION.
B
4.25
12 X 1.00 HOLES
FOR .75 FOUNDATION
BOLTS
1.25
6. UNBALANCED INERTIA FORCES : TX - 5180
VACUUM PUMP RPM : 450
SUBBASE OUTLINE
PIPE 'AD'
'AB'
38.00 29.50
4.25
1.25 GROUT
AA AC
1.25
120.00
5 SPACES@ 24.00"
11. COMPANION FLANGES, BOLTS, NUTS AND GASKETS TO BE FURNISHED BY CUSTOMER.
12. INTAKE PIPE CONNECTION: THE INTAKE PIPE DIAMETER MUST BE AT THE SIZE GIVEN ON THE
PLAN. THE INTAKE PIPE SHOULD BE AS SHORT AND DIRECT AS POSIBLE. USE LONG RADIUS BENDS,
AVOIDING SHARP ELBOWS AND TURNS, ALSO PROVIDE FOR EXPANSION OF PIPE.
144.00
ANCHOR BOLT DETAILS
NO OF BOLTS : 12
A
2.00
SCALE 0.050
8
A
13. ATOMIZER ASSEMBLY : 8787-C1
1.00
BOLT
30.00
9. RECOMMENDED CLEARANCE ON THREE SIDES 36.00". 42.00" IN FRONT OF CONTROL PANEL (IF
MOUNTED ON SUBBASE) OR MIN. AS REQUIRED BY LATEST NATIONAL ELECTRICAL CODE OR
APPLICABLE LOCAL CODES.
10. AIR INLET & DISCH. CONNECTIONS: 10"-125LB STD. ASA FLANGE, 12 - .88" TAPPED HOLES. HOLES
TO STRADDLE CENTERLINE.
6.00
18.00
7. VACUUM PUMP HAS A COUNTERWEIGHT ON THE INSIDE OF THE SHEAVE RIM. THE SHEAVE SHOULD
BE INSTALLED WITH THE COUNTERWEIGHT LOCATED AT THE REAR OF THE COMPRESSOR FRAME
WHEN THE PISTON IS AS CLOSE TO THE OUTER HEAD AS POSSIBLE.
8. ASSEMBLE COMPRESSOR SHEAVE WITH BUSHING FLANGE TOWARD COMPRESSOR FRAME.
CRANKSHAFT TO BE FLUSH WITH END OF BUSHING.
Y
12.00
B
7
6
SLEEVE
PROJ.
AA
AB
AC
AD
Y
609.6
[24]
19.1
[0.75]
457.2
[18.00]
50.8
[2]
76.2
[3]
5
4
UNLESS OTHERWISE SPECIFIED PRINTED DOCUMENT IS UNCONTROLLED
PROPRIETARY NOTICE
THIS DRAWING CONTAINS CONFIDENTIAL AND TRADE SECRET
INFORMATION, IS THE PROPERTY OF INGERSOLL-RAND CO., AND
IS GIVEN TO THE RECEIVER IN CONFIDENCE. THE RECEIVER BY
RECEPTION AND RETENTION OF THE DRAWING ACCEPTS THE
DRAWING IN CONFIDENCE AND AGREES THAT, EXCEPT AS
AUTHORIZE D IN WRITING BY INGERSOLL-RAND CO. IT WILL (1)
NOT USE THE DRAWING OR ANY COPY THEREOF OR THE
CONFIDENTIAL OR TRADE SECRET INFORMATION THEREIN; (2) NOT
COPY THE DRAWING; (3) NOT DISCLOSE TO OTHERS EITHER THE
DRAWING OR THE CONFIDENTIAL OR TRADESECRET INFORMATION
THEREIN; AND (4) UPON COMPLETION OF THE NEED TO RETAIN
THE DRAWING, OR UPON DEMAND, RETURN THE DRAWING, ALL
COPIES THEREOF, AND ALL MATERIAL COPIED THEREFROM.
3
2
NAME
SIZE
ARRANGEMENT, 22
X 7 ESH-VP
A1
SCALE
DWG NO.
47534468
PART NO.
NOMENCLATURE
0.20
47534468
ARRANGEMENT, 22 X 7 ESH-VP
REVISION
SHEET
A
2 OF 2
1
A.0