Register your product and get support at
www.philips.com/dictation
DPM8500
Barcode scanner configuration guide
Table of contents
1Introduction
5
2 Set default parameter
7
3UPC/EAN
8
Operational Parameters
Parameter defaults
Enable/Disable UPC-A
Enable/Disable UPC-E
Enable/Disable UPC-E1
Enable/Disable EAN-8
Enable/Disable EAN-13
Enable/Disable Bookland EAN
Bookland ISBN Format
Decode UPC/EAN Supplementals
Decode UPC/EAN Supplemental Redundancy
UPC/EAN/JAN Supplemental AIM ID Format
Transmit UPC-A Check Digit
Transmit UPC-E Check Digit
Transmit UPC-E1 Check Digit
UPC-A Preamble
UPC-E Preamble
UPC-E1 Preamble
Convert UPC-E to UPC-A
Convert UPC-E1 to UPC-A
EAN Zero Extend
UPC/EAN Security Level
UCC Coupon Extended Code
Coupon Report
ISSN EAN
4 Code 128
Enable/Disable Code 128
Set Lengths for Code 128
Enable/Disable GS1-128 (formerly UCC/EAN-128)
Enable/Disable ISBT 128
ISBT Concatenation
Check ISBT Table
ISBT Concatenation Redundancy
5 Code 39
Enable/Disable Code 39
Enable/Disable Trioptic Code 39
Convert Code 39 to Code 32 (Italian Pharma Code)
Code 32 Prefix
Set Lengths for Code 39
Code 39 Check Digit Verification
Transmit Code 39 Check Digit
Enable/Disable Code 39 Full ASCII
6 Code 93
Enable/Disable Code 93
Set Lengths for Code 93
Barcode scanner configuration guide
5
5
8
8
9
9
10
10
11
11
13
13
14
15
15
16
17
18
18
19
19
20
21
22
23
24
24
25
26
26
27
27
28
29
29
29
30
30
31
32
32
33
34
7 Code 11
36
8 Interleaved 2 of 5
39
9 Discrete 2 of 5
42
10Chinese 2 of 5
44
11Matrix 2 of 5
45
12Inverse 1D
48
13Codabar
49
14MSI
51
15GS1-DataBar
54
16Numeric Bar Codes
56
Enable/Disable Code 11
Set Lengths for Code 11
Code 11 Check Digit Verification
Transmit Code 11 Check Digits
Enable/Disable Interleaved 2 of 5
Set Lengths for Interleaved 2 of 5
I 2 of 5 Check Digit Verification
Transmit I 2 of 5 Check Digit
Convert I 2 of 5 to EAN-13
Enable/Disable Discrete 2 of 5
Set Lengths for Discrete 2 of 5
Enable/Disable Chinese 2 of 5
Enable/Disable Matrix 2 of 5
Set Lengths for Matrix 2 of 5
Matrix 2 of 5 Redundancy
Matrix 2 of 5 Check Digit
Transmit Matrix 2 of 5 Check Digit
Enable/Disable Codabar
Set Lengths for Codabar
CLSI Editing
NOTIS Editing
Enable/Disable MSI
Set Lengths for MSI
MSI Check Digits
Transmit MSI Check Digit
MSI Check Digit Algorithm
Enable/Disable GS1 DataBar Omnidirectional
Enable/Disable GS1 DataBar Limited
Enable/Disable GS1 DataBar Expanded
Convert GS1 DataBar to UPC/EAN
36
37
38
38
39
39
40
41
41
42
42
44
45
46
47
47
47
49
49
50
50
51
51
52
52
53
54
54
55
55
Cancel57
34
35
3
4
Barcode scanner configuration guide
1 Introduction
This booklet describes the programmable parameters, and provides bar codes for programming the Pocket Memo dictation recorder with barcode
scanner.
Operational Parameters
The Pocket Memo dictation recorder with barcode scanner is shipped with the factory default settings shown in the table below. These factory default
values are stored in non-volatile memory and are preserved even when the scanner is powered down.
To change the parameter values:
aScan the appropriate bar codes included in this chapter.
XXThe new values replace the existing memory values.
bThe factory default values can be recalled by scanning the RESTORE DEFAULTS bar code on page 7.
Parameter defaults
The table lists the factory defaults for all parameters. To change any option, scan the appropriate bar code(s).
Parameter
Set Factory Default
UPC/EAN
UPC-A
UPC-E
UPC-E1
EAN-8
EAN-13
Bookland EAN
Bookland ISBN Format
Decode UPC/EAN Supplementals
Decode UPC/EAN Supplemental Redundancy
UPC/EAN/JAN Supplemental AIM ID Format
Transmit UPC-A Check Digit
Transmit UPC-E Check Digit
Transmit UPC-E1 Check Digit
UPC-A Preamble
UPC-E Preamble
UPC-E1 Preamble
Convert UPC-E to A
Convert UPC-E1 to A
EAN-8 Zero Extend
UPC/EAN Security Level
UCC Coupon Extended Code
Coupon Report
ISSN EAN
Code 128
Code 128
Set Length(s) for Code 128
GS1-128 (formerly UCC/EAN-128)
ISBT 128
ISBT Concatenation
Check ISBT Table
ISBT Concatenation Redundancy
Code 39
Code 39
Trioptic Code 39
Convert Code 39 to Code 32
Barcode scanner configuration guide
Parameter no (Hex)
Factory default
All Defaults
01h
02h
0Ch
04h
03h
53h
F1h 40h
10h
50h
F1h A0h
28h
29h
2Ah
22h
23h
24h
25h
26h
27h
4Dh
55h
F1h DAh
F1h 69h
Enable
Enable
Disable
Enable
Enable
Disable
ISBN-10
Ignore
7
Combined
Enable
Enable
Enable
System Character
System Character
System Character
Disable
Disable
Disable
1
Disable
Both Coupon Formats
Disable
08h
D1h
D2h
0Eh
54h
F1h 41h
F1h 42h
DFh
Enable
1-55
Enable
Enable
Disable
Enable
10
00h
0Dh
56h
Enable
Disable
Disable
5
Parameter
Parameter no (Hex)
Factory default
Code 32 Prefix
Set Length(s) for Code 39
E7h
12h
13h
30h
2Bh
11h
Disable
2-55
Code 39 Check Digit Verification
Transmit Code 39 Check Digit
Code 39 Full ASCII Conversion
Code 93
Code 93
Set Length(s) for Code 93
Code 11
Code 11
Set Lengths for Code 11
Code 11 Check Digit Verification
Transmit Code 11 Check Digit(s)
Interleaved 2 of 5
Interleaved 2 of 5
Set Length(s) for I 2 of 5
I 2 of 5 Check Digit Verification
Transmit I 2 of 5 Check Digit
Convert I 2 of 5 to EAN 13
Discrete 2 of 5
Discrete 2 of 5
Set Length(s) for D 2 of 5
Chinese 2 of 5
Chinese 2 of 5
Matrix 2 of 5
Matrix 2 of 5
Matrix 2 of 5 Lengths
Matrix 2 of 5 Redundancy
Matrix 2 of 5 Check Digit
Transmit Matrix 2 of 5 Check Digit
Inverse 1D
Inverse 1D
Codabar
Codabar
Set Lengths for Codabar
CLSI Editing
NOTIS Editing
MSI
MSI
Set Length(s) for MSI
MSI Check Digits
Transmit MSI Check Digit
MSI Check Digit Algorithm
GS1 DataBar
GS1 DataBar Omnidirectional
GS1 DataBar Limited
GS1 DataBar Expanded
Convert GS1 DataBar to UPC/EAN
6
Disable
Disable
Disable
09h
1Ah
1Bh
Disable
4-55
0Ah
1Ch
1Dh
34h
2Fh
Disable
4 to 55
06h
16h
17h
31h
2Ch
52h
Disable
Disable
Enable
14
Disable
Disable
Disable
05h
14h
15h
Disable
12
F0h 98h
Disable
F1h 6Ah
F1h 6Bh
F1h 6Ch
F1h 6Dh
F1h 6Eh
F1h 6Fh
Disable
14
Disable
Disable
Disable
F1h 4Ah
Regular
07h
18h
19h
36h
37h
Disable
5-55
0Bh
1Eh
1Fh
32h
2Eh
33h
F0h 52h
F0h 53h
F0h 54h
F0h
8Dh
Disable
Disable
Disable
6-55
One
Disable
Mod 10/Mod 10
Enable
Enable
Enable
Disable
Barcode scanner configuration guide
Set Default Parameter
2 Set default parameter
Scan Set Factory Defaults to restore the factory default values listed in Table 4-1 on page 4-2.
Scan Set Factory Defaults to restore the factory default values listed in the table on page 5.
Set Factory Defaults
LED On Time
Parameter # 88h
This parameter sets the maximum time decode processing continues during a scan attempt. It is programmable in 0.1
second increments from 0.50 to 25.5 seconds.
To set an LED On Time, scan the bar code below. Next scan two numeric bar codes beginning on page 4-73 that
correspond to the desired on time. Single digit numbers must have a leading zero. For example, to set an on time of 0.5
seconds, scan the bar code below, then scan the "0", "5" and "0" bar codes; to set an on time of 10.5 seconds, scan the bar
code below, then scan the "1", "0" and "5" bar codes. To change the selection or cancel an incorrect entry, scan Cancel on
page 4-74.
LED On Time
(Default: 3.0 sec.)
Barcode scanner configuration guide
7
UPC/EAN
UPC/EAN
Enable/Disable UPC-A
3Enable/Disable
UPC/EAN UPC-A
Parameter # 01h
Parameter
# 01h
ToEnable/Disable
enable
or disable
UPC-A UPC-A, scan the appropriate bar code below.
ToParameter
enable or
disable UPC-A, scan the appropriate bar code below.
# 01h
To enable or disable UPC-A, scan the appropriate bar code below.
*Enable UPC-A
(01h)
*Enable UPC-A
(01h)
Enable/Disable UPC-E
Disable UPC-A
(00h)
Disable UPC-A
(00h)
Enable/Disable
Parameter
# 02hUPC-E
Enable/Disable UPC-E
Parameter
# 02h
ToParameter
enable
or
disable
UPC-E, scan the appropriate bar code below.
# 02h
To enable or disable UPC-E, scan the appropriate bar code below.
To enable or disable UPC-E, scan the appropriate bar code below.
*Enable UPC-E
(01h)
*Enable UPC-E
(01h)
Disable UPC-E
(00h)
Disable UPC-E
(00h)
8
Barcode scanner configuration guide
Parameter # 0Ch
To enable or disable UPC-E1, scan the appropriate bar code below.
To enable or disable UPC-E1, scan the appropriate bar code below.
Enable/Disable UPC-E1
NOTE UPC-E1 is not a UCC (Uniform Code Council) approved symbology.
Parameter
# 0ChUPC-E1 is not a UCC (Uniform Code Council) approved symbology.
NOTE
To enable or disable UPC-E1, scan the appropriate bar code below.
NOTE: UPC-E1 is not a UCC (Uniform Code Council) approved symbology.
Enable UPC-E1
(01h)
Enable
UPC-E1
(01h)
*Disable UPC-E1
(00h)
*Disable
UPC-E1
(00h)
Enable/Disable EAN-8
Enable/Disable EAN-8
Parameter # 04h
Enable/Disable EAN-8
Parameter # 04h
ToParameter
enable or
disable EAN-8, scan the appropriate bar code below.
# 04h
ToToenable
ordisable
disable
EAN-8,
scan
the appropriate
bar code below.
enable or
EAN-8,
scan the
appropriate
bar code below.
*Enable EAN-8
(01h)
*Enable
EAN-8
(01h)
Disable EAN-8
(00h)
Disable
EAN-8
(00h)
Barcode scanner configuration guide
9
Enable/Disable
Parameter
# 03hEAN-13
ToEnable/Disable
enable
or disable
scan the appropriate bar code below.
Parameter
# EAN-13,
03h
EAN-13
Parameter
To
enable #
or03h
disable EAN-13, scan the appropriate bar code below.
To enable or disable EAN-13, scan the appropriate bar code below
*Enable EAN-13
(01h)
*Enable EAN-13
(01h)
Enable/Disable Bookland EAN
Disable EAN-13
(00h)
Disable EAN-13
(00h)
Enable/Disable Bookland EAN
Parameter
# h53h
Enable/Disable
Bookland
EAN
ToParameter
enable
or
disable
# h53h
Parameter
# EAN
h53hBookland, scan the appropriate bar code below.
To enable or disable EAN Bookland, scan the appropriate bar code below.
To enable or disable EAN Bookland, scan the appropriate bar code below.
Enable Bookland EAN
(01h)
Enable Bookland EAN
(01h)
*Disable Bookland EAN
(00h)
*Disable Bookland EAN
(00h)
NOTE: If you enable Bookland EAN, select a Bookland ISBN Format. Also select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/
EAN Supplementals,
or Enable
Supplemental
Mode
in Decode ISBN
UPC/EAN
Supplementals.
NOTE If you
enable978/979
Bookland
EAN, select
a Bookland
Format
on page 4-16. Also select either Decode
UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 Supplemental
Decode
UPC/EAN
Supplementals
on page
4-17.
NOTE Mode
If you in
enable
Bookland
EAN,
select a Bookland
ISBN
Format on page 4-16. Also select either Decode
UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 Supplemental
Mode in Decode UPC/EAN Supplementals on page 4-17.
10
Barcode scanner configuration guide
Parameter # F1h 40h
IfBookland
Bookland
EAN
is enabled, select one of the following formats for Bookland data:
ISBN
Format
Parameter
# F1h 40h
• Bookland
ISBN-10 - The digital scanner reports Bookland data starting with 978 in traditional 10-digit format with the
If Bookland
EAN
is enabled, check
select one
of the
formats for BooklandData
data: starting with 979 is not considered Bookland in this
special
Bookland
digit
for following
backward-compatibility.
mode.ISBN-10 - The digital scanner reports Bookland data starting with 978 in traditional 10-digit format with the special Bookland check digit
• Bookland
backward-compatibility. Data starting with 979 is not considered Bookland in this mode.
•for Bookland
ISBN-13 - The digital scanner reports Bookland data (starting with either 978 or 979) as EAN-13 in 13-digit
• Bookland
ISBN-13
- The
scanner
reports
Bookland data (starting with either 978 or 979) as EAN-13 in 13-digit format to meet the 2007
format
to meet
thedigital
2007
ISBN-13
protocol.
ISBN-13 protocol.
•
*Bookland ISBN-10
(00h)
Bookland ISBN-13
(01h)
NOTE: For
Bookland
to function
ensure
Bookland
EAN Bookland
is enabled (see
Bookland
EAN), then select
either Decode
NOTE
ForEAN
Bookland
EANproperly,
to function
properly,
ensure
EANEnable/Disable
is enabled (see
Enable/Disable
Bookland
UPC/EAN Supplementals,
Autodiscriminate
UPC/EAN
Supplementals,
or
Enable
978/979
Supplemental
Mode
in
Decode
UPC/EAN
EAN on page 4-15), then select either Decode UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals.
Supplementals, or Enable 978/979 Supplemental Mode in Decode UPC/EAN Supplementals on page
Decode UPC/EAN
Supplementals
4-17.
Parameter # 10h
Supplementals are bar codes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2).
The following options are available:
• If you select Ignore UPC/EAN with Supplementals, and the scanner is presented with a UPC/EAN plus supplemental symbol, the scanner decodes
UPC/EAN and ignores the supplemental characters.
• If you select Decode UPC/EAN with Supplementals, the scanner only decodes UPC/EAN symbols with supplemental characters, and ignores
symbols without supplementals.
• If you select Autodiscriminate UPC/EAN Supplementals, the scanner decodes UPC/EAN symbols with supplemental characters immediately. If
the symbol does not have a supplemental, the scanner must decode the bar code the number of times set via Decode UPC/EAN Supplemental
Redundancy before transmitting its data to confirm that there is no supplemental.
• If you select one of the following Supplemental Mode options, the scanner immediately transmits EAN-13 bar codes starting with that prefix that
have supplemental characters. If the symbol does not have a supplemental, the scanner must decode the bar code the number of times set via
Decode UPC/EAN Supplemental Redundancy before transmitting its data to confirm that there is no supplemental. The scanner transmits UPC/
EAN bar codes that do not have that prefix immediately.
• Enable 378/379 Supplemental Mode.
• Enable 978/979 Supplemental Mode.
»» NOTE: If you select 978/979 Supplemental Mode and are scanning Bookland EAN bar codes, see Enable/Disable Bookland EAN to enable
Bookland EAN, and select a format using Bookland ISBN Format.
• Enable 977 Supplemental Mode.
• Enable 414/419/434/439 Supplemental Mode.
• Enable 491 Supplemental Mode.
• Enable Smart Supplemental Mode - applies to EAN-13 bar codes starting with any prefix listed previously.
»» NOTE: To minimize the risk of invalid data transmission, select either to decode or ignore supplemental characters.
Barcode scanner configuration guide
11
Decode UPC/EAN Supplementals (continued)
Select
desired
option
by scanning
one
of thebar
following
Select the
the desired
option
by scanning
one of the
following
codes. bar codes.
Decode UPC/EAN With Supplementals
(01h)
*Ignore UPC/EAN With Supplementals
(00h)
Autodiscriminate UPC/EAN Supplementals
(02h)
Enable 378/379 Supplemental Mode
(04h)
Enable 978/979 Supplemental Mode
(05h)
12
Barcode scanner configuration guide
Decode UPC/EAN Supplementals (continued)
Decode UPC/EAN Supplementals (continued)
Enable 977 Supplemental Mode
(07h)
Enable 977 Supplemental
Mode
(07h)
Enable 414/419/434/439 Supplemental Mode
(06h)Supplemental Mode
Enable 414/419/434/439
(06h)
Enable 491 Supplemental Mode
(08h)
Enable 491 Supplemental
Mode
(08h)
Enable Smart Supplemental Mode
(03h)
Enable Smart Supplemental
Mode
(03h)
Decode UPC/EAN Supplemental Redundancy
Decode UPC/EAN Supplemental Redundancy
Parameter
# 50h
Decode
UPC/EAN Supplemental
Redundancy
Parameter
#
50h
Parameter # 50h
With Autodiscriminate UPC/EAN Supplementals selected, this option adjusts the number of times a symbol without
WithAutodiscriminate
Autodiscriminate
UPC/EAN
Supplementals
selected, this
option
adjusts
the number
of times.
times
symbol
supplementals
decoded
supplementals
are decoded
before
transmission.
The
range
is from
2 adjusts
to 20
Five orwithout
above
isarecommended
when
With
UPC/EAN
Supplementals
selected,
this
option
theanumber
of
times
symbolare
without
decoding
a
mix
of
UPC/EAN
symbols
with
and
without
supplementals,
and
the
autodiscriminate
option
is
selected.
before transmission.
range is from
2 totransmission.
20 times. Five orThe
aboverange
is recommended
mix of
with and without
supplementals
areThe
decoded
before
is from 2 when
to 20decoding
times. aFive
orUPC/EAN
above issymbols
recommended
when
decoding
a mix
UPC/EAN
symbols
with
and without
autodiscriminate
option
selected.
supplementals,
andofthe
autodiscriminate
option
is selected.
Scan thesupplementals,
bar code below to and
selectthe
a decode
redundancy value.
Nextis
scan
two numeric bar
Scan the bar code below to select a decode redundancy value. Next scan two numeric bar codes beginning on page 4-73.
codes beginning on page 56. Single digit numbers must have a leading zero. To change the selection or cancel an incorrect entry, scan Cancel on page
Single
digit
numbers
musttohave
a leading
zero.
To change
the selection
or two
cancel
an incorrect
entry,
scan Cancel
on page
Scan the
bar
code below
select
a decode
redundancy
value.
Next scan
numeric
bar codes
beginning
on page
4-73.
57.
4-74.
Single digit numbers must have a leading zero. To change the selection or cancel an incorrect entry, scan Cancel on page
4-74.
Decode UPC/EAN Supplemental Redundancy
7)
Decode UPC/EAN(Default:
Supplemental
Redundancy
(Default: 7)
Barcode scanner configuration guide
13
Parameter # F1h A0h
Select an output format when reporting UPC/EAN/JAN bar codes with Supplementals with Transmit Code ID Character on
AIM Code AIM
ID Character
page
4-67 set to
UPC/EAN/JAN
Supplemental
ID Format:
• Separate
UPC/EAN with supplementals with separate AIM IDs but one transmission, i.e.:
Parameter
# F1h- transmit
A0h
Select an]E<0
output
when reporting
UPC/EAN/JAN bar codes
orformat
4><data>]E<1
or 2>[supplemental
data]with Supplementals with Transmit Code ID Character set to AIM Code ID
Character:
• Combined – transmit UPC/EAN with supplementals with one AIM ID and one transmission, i.e.:
• Separate - transmit UPC/EAN with supplementals with separate AIM IDs but one transmission, i.e.:
data> data]
]E<0 ]E3<data+supplemental
or 4><data>]E<1 or 2>[supplemental
••Combined
– transmit
UPC/EAN -with
supplementals
with one
AIM
ID and one transmission,
i.e.:
Separate
Transmissions
transmit
UPC/EAN
with
supplementals
with separate
AIM IDs and separate transmissions,
]E3<data+supplemental
data>
i.e.:
• Separate
Transmissions
- transmit UPC/EAN with supplementals with separate AIM IDs and separate transmissions, i.e.:
]E<0
or 4><data>
]E<0 ]E<1
or 4><data>
or 2>[supplemental data]
]E<1 or 2>[supplemental data]
Separate
(00h)
*Combined
(01h)
Parameter Menus 4 - 21
Transmit UPC-A Check Digit
Separate Transmissions
NEW END
Parameter # 28h
Transmit UPC-A Check Digit
Scan
the appropriate bar code below to transmit the symbol with or without the UPC-A check digit.
Parameter # 28h
Scan the appropriate bar code below to transmit the symbol with or without the UPC-A check digit.
*Transmit UPC-A Check Digit
(01h)
Do Not Transmit UPC-A Check Digit
(00h)
14
Transmit UPC-E Check Digit
Parameter # 29h
Barcode scanner configuration guide
Transmit UPC-E Check Digit
Parameter # 29h
Transmit UPC-E Check Digit
Scan
the appropriate
bar code below to transmit the symbol with or without the UPC-E check digit.
Parameter
# 29h
Scan the appropriate bar code below to transmit the symbol with or without the UPC-E check digit.
*Transmit UPC-E Check Digit
(01h)
4 - 22 SE655 Decoded Linear Imaging Engine
Do Not Transmit UPC-E Check Digit
(00h)
Transmit UPC-E1 Check Digit
Transmit UPC-E1 Check Digit
Parameter # 2Ah
Parameter # 2Ah
Scan the
the appropriate
bar bar
codecode
belowbelow
to transmit
the symbolthe
with
or without
theorUPC-E1
check
Scan
appropriate
to transmit
symbol
with
without
thedigit.
UPC-E1 check digit.
*Transmit UPC-E1 Check Digit
(01h)
Do Not Transmit UPC-E1 Check Digit
(00h)
UPC-A Preamble
Parameter # 22h
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of
the following options for transmitting UPC-A preamble to the host device: transmit system character only, transmit system
character and country code (“0” for USA), or transmit no preamble.
No Preamble
(<DATA>)
(00h)
Barcode scanner configuration guide
15
(00h)
UPC-A Preamble
UPC-A Preamble
Parameter
Parameter
# 22h # 22h
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of the following options for
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A symbol. Select one of
transmitting UPC-A preamble to the host device: transmit system character only, transmit system character and country code (“0” for USA), or
the following options for transmitting UPC-A preamble to the host device: transmit system character only, transmit system
transmit no
preamble.
character
and
country code (“0” for USA), or transmit no preamble.
No Preamble
(<DATA>)
(00h)
*System Character
(<SYSTEM CHARACTER> <DATA>)
(01h)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)
(02h)
16
Barcode scanner configuration guide
UPC-E Preamble
Parameter # 23h
UPC-E Preamble
Preamble
(Country Code and System Character) can be transmitted as part of a UPC-E symbol. Select one of
Parametercharacters
# 23h
the
following
options
for
transmitting
UPC-E
preamble
totransmitted
the host device:
system
character
only,
transmit
system
Preamble characters (Country
Code and System
Character)
can be
as part of transmit
a UPC-E symbol.
Select
one of the
following
options
for
character and country code (“0” for USA), or transmit no preamble.
transmitting UPC-E preamble to the host device: transmit system character only, transmit system character and country code (“0” for USA), or
transmit no preamble.
No Preamble
(<DATA>)
(00h)
*System Character
(<SYSTEM CHARACTER> <DATA>)
(01h)
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)
(02h)
Barcode scanner configuration guide
17
UPC-E1 Preamble
Parameter # 24h
UPC-E1 Preamble
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E1 symbol. Select one of
Parameter # 24h
the following options for transmitting UPC-E1 preamble to the host device: transmit system character only, transmit system
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E1 symbol. Select one of the following options for
character and country code (“0” for USA), or transmit no preamble.
transmitting UPC-E1 preamble to the host device: transmit system character only, transmit system character and country code (“0” for USA), or
transmit no preamble.
No Preamble
(<DATA>)
(00h)
*System Character
(<SYSTEM CHARACTER> <DATA>)
(01h)
Parameter Menus 4 - 25
System Character & Country Code
(< COUNTRY CODE> <SYSTEM CHARACTER> <DATA>)
(02h)
Convert UPC-E to UPC-A
Parameter
# 25h
Convert
UPC-E to UPC-A
Enable
this#parameter
to convert UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After
Parameter
25h
conversion,
data follows
UPC-A
format
and is affected
bydata
UPC-A
programming
selections
Check
Digit).
Enable this parameter
to convert
UPC-E
(zero suppressed)
decoded
to UPC-A
format before
transmission.(e.g.,
AfterPreamble,
conversion, data
follows
UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit).
Scan
DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E (zero suppressed) decoded data.
Scan DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E (zero suppressed) decoded data.
Convert UPC-E to UPC-A (Enable)
(01h)
*Do Not Convert UPC-E to UPC-A (Disable)
(00h)
Convert UPC-E1 to UPC-A
Parameter # 26h
18
configuration
guide
Enable
this parameter to convert UPC-E1 (zero suppressed) decoded data to UPC-A formatBarcode
beforescanner
transmission.
After
conversion, data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit).
Convert UPC-E1 to UPC-A
Parameter
26h
Convert
UPC-E1 to#UPC-A
Enable
this#parameter
to convert UPC-E1 (zero suppressed) decoded data to UPC-A format before transmission. After
Parameter
26h
conversion,
data follows
UPC-A
format
is affected
by UPC-A
programming
selections
(e.g.,
Preamble,
Digit).
Enable this parameter
to convert
UPC-E1
(zeroand
suppressed)
decoded
data to UPC-A
format before
transmission.
After
conversion, Check
data follows
UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit).
Scan DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E1 (zero suppressed) decoded data.
Scan DO NOT CONVERT UPC-E TO UPC-A to transmit UPC-E1 (zero suppressed) decoded data.
Convert UPC-E1 to UPC-A (Enable)
(01h)
4 - 26 SE655 Decoded Linear Imaging Engine
EAN Zero Extend
*Do Not Convert UPC-E1 to UPC-A (Disable)
(00h)
Parameter # 27h
EAN Zero Extend
When enabled, this parameter adds five leading zeros to decoded EAN-8 symbols to make them compatible in format to
Parameter
# 27h
EAN-13
symbols.
When enabled, this parameter adds five leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols.
Disable this parameter to transmit EAN-8 symbols as is.
Disable this parameter to transmit EAN-8 symbols as is.
Enable EAN Zero Extend
(01h)
*Disable EAN Zero Extend
(00h)
Barcode scanner configuration guide
19
UPC/EAN
UPC/EAN Security
Security Level
Level
UPC/EAN
Security Level
Parameter
# 4Dh
Parameter # 4Dh
Parameter # 4Dh
The SE655
SE655 offers four
four levels
levels of
of decode
decode security
security for
for UPC/EAN
UPC/EAN bar
bar codes.
codes. Increasing
Increasing levels
levels of
of security are
are provided
provided for
for
The
The scanner offers
offers four levels
of decode
security for UPC/EAN
bar codes. Increasing
levels of security are
providedsecurity
for decreasing levels
of bar code
decreasing levels
levels of
of bar
bar code
code quality.
quality. Select
Select higher
higher levels
levels of
of security
security for
for decreasing
decreasing levels
levels of
of bar
bar code
code quality.
quality. Increasing
Increasing
decreasing
quality. Select higher levels of security for decreasing levels of bar code quality. Increasing security decreases the scan engine’s aggressiveness, so choose
security decreases
decreases the
the scan
scan engine’s
engine’s aggressiveness,
aggressiveness, so
so choose
choose only
only that
that level
level of
of security
security necessary
necessary for
for the
the application.
application.
security
only that level of security necessary for the application.
UPC/EAN
Security
UPC/EAN
Security Level
Level 00
UPC/EAN Security Level 0
This
setting
allows
the
scan
engine
in
state,
while
providing
sufficient
security
in
Thisdefault
default setting
allows
the scan
operateto
its most aggressive
state,aggressive
while providing
sufficient
security
in decoding
most “in-spec”
This
default
setting
allows
theengine
scan to
engine
toinoperate
operate
in its
its most
most
aggressive
state,
while
providing
sufficient
securityUPC/
in
decoding
most
“in-spec”
UPC/EAN
bar
codes.
most “in-spec” UPC/EAN bar codes.
EAN bar codes.
decoding
UPC/EAN Security
Security Level
Level 0
0
UPC/EAN
(00h)
(00h)
UPC/EAN Security Level 1
UPC/EAN Security Level 1
As bar
bar code
code quality
quality levels
levels diminish,
diminish, certain
certain characters
characters become
become prone
prone to
to mis-decodes
mis-decodes before
before others
others (i.e.,
(i.e., 1,
1, 2,
2, 7,
7, 8).
8). If
If
As
As bar code quality levels diminish, certain characters become prone to mis-decodes before others (i.e., 1, 2, 7, 8). If mis-decodes of poorly printed
mis-decodes of
of poorly
poorly printed
printed bar
bar codes
codes occur,
occur, and
and the
the mis-decodes
mis-decodes are
are limited
limited to
to these
these characters,
characters, select
select this
this security
security
mis-decodes
bar codes occur, and the mis-decodes are limited to these characters, select this security level.
level.
level.
*UPC/EAN
*UPC/EAN Security
Security Level
Level 1
1
(01h)
(01h)
UPC/EAN
UPC/EAN Security
Security Level
Level 22
UPC/EAN Security Level 2
If mis-decodes
mis-decodes of
of poorly
poorly printed
printed bar
bar codes
codes occur,
occur, and
and the
the mis-decodes
mis-decodes are
are not
not limited
limited to
to characters
characters 1,
1, 2,
2, 7,
7, and
and 8,
8, select
select
If
If mis-decodes
of poorly printed bar codes occur, and the mis-decodes are not limited to characters 1, 2, 7, and 8, select this security level.
this
security level.
level.
this
security
UPC/EAN
UPC/EAN Security
Security Level
Level 2
2
(02h)
(02h)
UPC/EAN
UPC/EAN Security
Security Level
Level 33
UPC/EAN Security Level 3
If misdecodes
misdecodes still
still occur
occur after
after selecting
selecting Security
Security Level
Level 2,
2, select
select this
this security level.
level. Be advised,
advised, selecting this
this option
option is
is an
an
If
If misdecodes still occur
after selecting
Security Level 2, select
this security
level. Besecurity
advised, selecting Be
this option is anselecting
extreme measure
against misextreme measure
measure against
against mis-decoding
mis-decoding severely
severely out
out of
of spec
spec bar
bar codes.
codes. Selection
Selection of
of this
this level
level of
of security
security significantly
significantly
extreme
decoding severely out of spec bar codes. Selection of this level of security significantly impairs the decoding ability of the scan engine. If this level of
impairs
the decoding
decoding ability
ability of
of the
the scan
scan engine.
engine. If
If this
this level
level of
of security
security is
is necessary,
necessary, try
try to
to improve
improve the
the quality
quality of
of the
the bar
bar
impairs
the
security is necessary, try to improve the quality of the bar codes.
codes.
codes.
UPC/EAN Security
Security Level
Level 3
3
UPC/EAN
(03h)
(03h)
20
Barcode scanner configuration guide
UCC Coupon Extended Code
Parameter # 55h
UCC Coupon Extended Code
The
UCC Coupon
Parameter
# 55h Extended Code is an additional bar code adjacent to a UCC Coupon Code. To enable or disable UCC
Coupon
Extended
Code, scan
appropriate
bar adjacent
code below.
The UCC Coupon Extended
Code isthe
an additional
bar code
to a UCC Coupon Code. To enable or disable UCC Coupon Extended Code,
scan the appropriate bar code below.
Enable UCC Coupon Extended Code
(01h)
*Disable UCC Coupon Extended Code
(00h)
Barcode scanner configuration guide
21
Parameter # F1h DAh
Coupon Report
Traditional
coupon symbols (old coupon symbols) are composed of two bar codes: UPC/EAN and Code128. A new coupon
symbol
is
composed
Parameter # F1h DAh of a single Databar Expanded bar code. The new coupon format offers more options for purchase
values (up to $999.99) and supports complex discount offers such as a second purchase requirement.
Traditional coupon symbols (old coupon symbols) are composed of two bar codes: UPC/EAN and Code128. A new coupon symbol is composed of a
Databar
Expanded
bar code.
new that
coupon
format offers
options
forcodes:
purchaseUPC/EAN
values (up toand
$999.99)
and supports
complex
Ansingle
interim
coupon
symbol
alsoThe
exists
contains
bothmore
types
of bar
Databar
Expanded.
Thisdiscount
format
accommodates
both purchase
retailersrequirement.
that do not recognize or use the additional information included in the new coupon symbol, as
offers such as a second
well as those who can process new coupon symbols.
An interim coupon symbol also exists that contains both types of bar codes: UPC/EAN and Databar Expanded. This format accommodates both
Scan
a bar
to select
one
of the information
following included
optionsinfor
symbols:
retailers
thatcode
do notbelow
recognize
or use the
additional
thedecoding
new couponcoupon
symbol, as
well as those who can process new coupon
symbols.
• Old Coupon Symbols - Scanning an old coupon symbol reports both UPC and Code 128, scanning an interim coupon
symbol reports UPC, and scanning a new coupon symbol reports nothing (no decode).
Scan a bar code below to select one of the following options for decoding coupon symbols:
New
Coupon
Symbols
- Scanning
ansymbol
old coupon
either
UPC oranCode
and
scanning
interim
••Old
Coupon
Symbols
- Scanning
an old coupon
reports symbol
both UPCreports
and Code
128, scanning
interim128,
coupon
symbol
reportsan
UPC,
and
coupon
symbol
a new
coupon
symbol
reports Databar Expanded.
scanning
a new
couponorsymbol
reports
nothing
(no decode).
••New
Coupon
Symbols
- Scanning
an old coupon
symbol
reportssymbol
either UPC
or Code
128,
and scanning
an interim
symbol oran
a new
Both
Coupon
Formats
- Scanning
an old
coupon
reports
both
UPC
and Code
128, coupon
and scanning
interim
coupon
symbol
reportsorDatabar
coupon
symbol
a newExpanded.
coupon symbol reports Databar Expanded.
• Both Coupon Formats - Scanning an old coupon symbol reports both UPC and Code 128, and scanning an interim coupon symbol or a new coupon
•
symbol reports Databar Expanded.
Old Coupon Symbols
(00h)
New Coupon Symbols
(01h)
*Both Coupon Formats
(02h)
22
Barcode scanner configuration guide
ISSN EAN
Parameter # F1h 69h
ISSN EAN
ToParameter
enable or
disable
# F1h
69h ISSN EAN, scan the appropriate bar code below
To enable or disable ISSN EAN, scan the appropriate bar code below
Enable ISSN EAN
(01h)
*Disable ISSN EAN
(00h)
Barcode scanner configuration guide
23
Code 128
4Enable/Disable
Code 128 Code 128
Parameter # 08h
Enable/Disable Code 128
To enable or disable Code 128, scan the appropriate bar code below.
Parameter # 08h
To enable or disable Code 128, scan the appropriate bar code below.
*Enable Code 128
(01h)
Disable Code 128
(00h)
Set Lengths for Code 128
Parameter # L1 = D1h L2 = D2h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Set lengths for Code 128 to any length, one or two discrete lengths, or lengths within a specific range.
NOTE
When setting lengths for different bar code types, enter a leading zero for single digit numbers.
• One Discrete Length - Select this option to decode only Code 128 symbols containing a selected length. Select the
length using the numeric bar codes beginning on page 4-73. For example, to decode only Code 128 symbols with 14
characters, scan Code 128 - One Discrete Length, then scan 1 followed by 4. To correct an error or change the
selection, scan Cancel on page 4-74.
• Two Discrete Lengths - Select this option to decode only Code 128 symbols containing either of two selected
lengths. Select lengths using the numeric bar codes beginning on page 4-73. For example, to decode only Code 128
symbols containing either 2 or 14 characters, select Code 128 - Two Discrete Lengths, then scan 0, 2, 1, and
then 4. To correct an error or change the selection, scan Cancel on page 4-74.
• Length Within Range - Select this option to decode a Code 128 symbol with a specific length range. Select
lengths using numeric bar codes beginning on page 4-73. For example, to decode Code 128 symbols containing
between 4 and 12 characters, first scan Code 128 - Length Within Range. Then scan 0, 4, 1, and 2 (enter a leading
zero for single digit numbers). To correct an error or change the selection, scan Cancel on page 4-74.
• Any Length - Select this option to decode Code 128 symbols containing any number of characters within the digital
scanner’s capability.
24
Barcode scanner configuration guide
Set Lengths for Code 128
Parameter # L1 = D1h L2 = D2h
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for
Code 128 to any length, one or two discrete lengths, or lengths within a specific range.
NOTE: When setting lengths for different bar code types, enter a leading zero for single digit numbers.
• One Discrete Length - Select this option to decode only Code 128 symbols containing a selected length. Select the length using the numeric bar
codes beginning on page 56. For example, to decode only Code 128 symbols with 14 characters, scan Code 128 - One Discrete Length, then
scan 1 followed by 4. To correct an error or change the selection, scan Cancel on page 57.
• Two Discrete Lengths - Select this option to decode only Code 128 symbols containing either of two selected lengths. Select lengths using the
numeric bar codes beginning on page 56. For example, to decode only Code 128 symbols containing either 2 or 14 characters, select Code 128 Two Discrete
thenLinear
scan 0, 2,Imaging
1, and thenEngine
4. To correct an error or change the selection, scan Cancel on page 57.
4 - 32
SE655 Lengths,
Decoded
• Length Within Range - Select this option to decode a Code 128 symbol with a specific length range. Select lengths using numeric bar codes
beginning on page 56. For example, to decode Code 128 symbols containing between 4 and 12 characters, first scan Code 128 - Length Within
Range. Then scan 0, 4, 1, and 2 (enter a leading zero for single digit numbers). To correct an error or change the selection, scan Cancel on page
Set Lengths for Code 128 (continued)
57.
• Any Length - Select this option to decode Code 128 symbols containing any number of characters within the digital scanner’s capability.
Code 128 - One Discrete Length
Code 128 - Two Discrete Lengths
Code 128 - Length Within Range
*Code 128 - Any Length
Barcode scanner configuration guide
25
Parameter
# 0EhGS1-128 (formerly UCC/EAN-128)
Enable/Disable
To enable or disable GS1-128, scan the appropriate bar code below. (See Appendix A, Miscellaneous Code Information for
Parameter
#(formerly
0Eh
details
on GS1-128
Enable/Disable
GS1-128
(formerlyUCC/EAN-128).)
UCC/EAN-128)
ToParameter
enable or
GS1-128, scan the appropriate bar code below. (See Appendix A, Miscellaneous Code Information for
# disable
0Eh
details
on
GS1-128
(formerly
To enable or disable GS1-128, scanUCC/EAN-128).)
the appropriate bar code below. (See Appendix A, Miscellaneous Code Information for details on GS1-128
(formerly UCC/EAN-128).)
*Enable GS1-128
(01h)
*Enable GS1-128
(01h)
Disable GS1-128
(00h)
Enable/Disable ISBT 128
Disable GS1-128
(00h)
Parameter # 54hISBT 128
Enable/Disable
Enable/Disable
ISBT 128
ToParameter
enable or
disable ISBT 128, scan the appropriate bar code below.
# 54h
Parameter # 54h
To enable or disable ISBT 128, scan the appropriate bar code below.
To enable or disable ISBT 128, scan the appropriate bar code below.
*Enable ISBT 128
(01h)
*Enable ISBT 128
(01h)
Disable ISBT 128
(00h)
Disable ISBT 128
(00h)
26
Barcode scanner configuration guide
Select an option for concatenating pairs of ISBT code types:
• IfConcatenation
you select Disable ISBT Concatenation, the digital scanner does not concatenate pairs of ISBT codes it
ISBT
encounters.
Parameter # F1h 41h
• If an
you
select
Enable ISBT
Select
option
for concatenating
pairsConcatenation,
of ISBT code types: there must be two ISBT codes in order for the digital scanner to decode
and
perform
concatenation.
The
scanner
does
not decode
single
ISBT
• If you select Disable ISBT Concatenation,
thedigital
digital scanner
does
not concatenate
pairs
of ISBT
codessymbols.
it encounters.
••If you
select
EnableAutodiscriminate
ISBT Concatenation, there
must
be two ISBT codes inthe
order
for the
digital scanner
to decode
and perform concatenation.
The
If you
select
ISBT
Concatenation,
digital
scanner
decodes
and concatenates
pairs of ISBT
digital
scanner
does not decode
single
ISBT symbols.
codes
immediately.
If only
a single
ISBT symbol is present, the digital scanner must decode the symbol the number of
times
setAutodiscriminate
via ISBT Concatenation
Redundancy
on page
4-35and
before
transmitting
data
toimmediately.
confirm that
there
is no
• If you
select
ISBT Concatenation,
the digital scanner
decodes
concatenates
pairs ofits
ISBT
codes
If only
a single
additional
ISBT
symbol
ISBT symbol is present, the digital scanner must decode the symbol the number of times set via ISBT Concatenation Redundancy before transmitting
its data to confirm that there is no additional ISBT symbol
*Disable ISBT Concatenation
(00h)
Enable ISBT Concatenation
(01h)
Parameter Menus 4 - 35
Check ISBT Table
Autodiscriminate ISBT Concatenation
(00h)
Parameter # F1h 42h
Check ISBT Table
The ISBT specification includes a table that lists several types of ISBT bar codes that are commonly used in pairs. If you
setParameter
ISBT Concatenation
to Enable, enable Check ISBT Table to concatenate only those pairs found in this table. Other
# F1h 42h
types
of
ISBT
codes
are
not
concatenated.
The ISBT specification includes a table
that lists several types of ISBT bar codes that are commonly used in pairs. If you set ISBT Concatenation to
Enable, enable Check ISBT Table to concatenate only those pairs found in this table. Other types of ISBT codes are not concatenated.
*Enable Check ISBT Table
(01h)
Disable Check ISBT Table
(00h)
ISBT Concatenation Redundancy
Parameter # DFh
Barcode
configuration guideto Autodiscriminate, use this parameter to set the number of times the digital scanner 27
If you
set scanner
ISBT Concatenation
must decode an ISBT symbol before determining that there is no additional symbol.
Parameter # DFh
If you set ISBT Concatenation to Autodiscriminate, use this parameter to set the number of times the digital scanner
ISBTdecode
Concatenation
Redundancy
must
an ISBT
symbol before determining that there is no additional symbol.
Parameter # DFh
Scan the bar code below, then scan two numeric bar codes in Numeric Bar Codes on page 4-73 to set a value between 2
If you
ISBT Concatenation
to Autodiscriminate,
this parameter
to set the
of change
times the a
digital
scanner must
an ISBT
symbol4-74.
and
20.setEnter
a leading zero
for single digituse
numbers.
To correct
annumber
error or
selection,
scandecode
Cancel
on page
before
determining
that
there
is
no
additional
symbol.
The default is 10.
Scan the bar code below, then scan two numeric bar codes in Numeric Bar Codes on page 56 to set a value between 2 and 20. Enter a leading zero
for single digit numbers. To correct an error or change a selection, scan Cancel on page 57. The default is 10.
ISBT Concatenation Redundancy
28
Barcode scanner configuration guide
Code 39
Code
39
5 Code
39
Enable/Disable Code 39
Enable/Disable
Parameter # 00hCode 39
Enable/Disable Code 39
Parameter
# 00h
ToParameter
enable
or
disable
Code 39, scan the appropriate bar code below.
# 00h
enable or
Code
39, scan
appropriate
bar code below.
ToToenable
or disable
disable
Code
39, the
scan
the appropriate
bar code below.
*Enable Code 39
(01h)
*Enable Code 39
(01h)
Enable/Disable Trioptic Code 39
Enable/Disable
Trioptic
Code 39
Enable/Disable
Trioptic
Code
39
Parameter
# 0Dh
Disable Code 39
(00h)
Disable Code 39
(00h)
Parameter
Trioptic
Code 39 is#a0Dh
variant of Code 39 used in marking computer tape cartridges. Trioptic Code 39 symbols always
Trioptic
Code
39 is a variant of Code 39 used in marking computer tape cartridges. Trioptic Code 39 symbols always contain six characters.
contain six
characters.
Trioptic Code 39 is a variant of Code 39 used in marking computer tape cartridges. Trioptic Code 39 symbols always
Toenable
enable
disable
Trioptic
CodeCode
39, scan
thescan
appropriate
bar code below.
contain
sixor
characters.
To
or
disable
Trioptic
39,
the appropriate
bar code below.
Parameter # 0Dh
To enable or disable Trioptic Code 39, scan the appropriate bar code below.
Enable Trioptic Code 39
(01h)
Enable Trioptic Code 39
(01h)
*Disable Trioptic Code 39
(00h)
*Disable Trioptic
Code 39
NOTE Trioptic Code 39 and Code 39 Full ASCII cannot(00h)
be enabledIf simultaneously.
the Enable
Trioptic
NOTE: Trioptic
Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.
the Enable TriopticIf Code
39 setting
is not Code
accepted*, disable
39 setting is not accepted*, disable Code 39 Full ASCII and try again.
Code 39NOTE
Full ASCII
and tryCode
again.39 and Code 39 Full ASCII cannot be enabled simultaneously. If the Enable Trioptic Code
Trioptic
39
setting
is not accepted*,
disable
Code
39 Full
ASCII
andhost
try again.
* An SSI parameter
entry error,
event
ID 07h,
is sent
to the
if packeted data communication is
* An SSI parameter
entry error,
eventthe
ID 07h,
sentthe
to the
host if packeted
communication
is enabled to inform the user that the parameter
enabled
to inform
useristhat
parameter
changedata
was
not accepted.
*
An
SSI
parameter
entry
error,
event
ID
07h,
is
sent
to
the
host
if
packeted
data communication is
change was not accepted.
enabled to inform the user that the parameter change was not accepted.
Barcode scanner configuration guide
29
Convert Code 39 to Code 32 (Italian Pharma Code)
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable
Parameter
# 56h
or disable
converting
Code 39 to Code 32.
Convert Code 39 to Code 32 (Italian Pharma Code)
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable
NOTE
must be enabled in order for this parameter to function.
# 56hCode 39
orParameter
disable converting
Code 39 to Code 32.
Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable or disable converting
Code 39NOTE
to CodeCode
32. 39 must be enabled in order for this parameter to function.
NOTE: Code 39 must be enabled in order for this parameter to function.
Enable Convert Code 39 to Code 32
(01h)
Enable Convert Code 39 to Code 32
(01h)
*Disable Convert Code 39 to Code 32
(00h)
Code 32 Prefix
*Disable Convert Code 39 to Code 32
(00h)
Parameter # E7h
Code
32 Prefix
Code
32 Prefix
Enable this parameter to add the prefix character “A” to all Code 32 bar codes. Convert Code 39 to Code 32 (Italian
Parameter
# E7hmust
Parameter
# E7h
Pharma
Code)
be enabled for this parameter to function.
Enable this parameter to add the prefix character “A” to all Code 32 bar codes. Convert Code 39 to Code 32 (Italian Pharma Code) must be enabled
Enable
parameter
to add the prefix character “A” to all Code 32 bar codes. Convert Code 39 to Code 32 (Italian
for this this
parameter
to function.
Pharma Code) must be enabled for this parameter to function.
Enable Code 32 Prefix
(01h)
Enable Code 32 Prefix
(01h)
*Disable Code 32 Prefix
(00h)
*Disable Code 32 Prefix
(00h)
30
Barcode scanner configuration guide
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains.
for
Code
39the
may
setof
forcharacters
any length,
onehuman
or tworeadable
discrete characters),
lengths, or lengths
within
a specific
If
The Parameter
lengthLengths
of a code
refers
to
(i.e.,
including
check
digit(s) range.
the code
# L1
= 12h
L2number
=be13h
Code
39
Full
ASCII
is
enabled,
Length
Within
a
Range
or
Any
Length
are
the
preferred
options.
To
set
lengths
via
serial
contains. Lengths for Code 39 may be set for any length, one or two discrete lengths, or lengths within a specific range. If
commands,
see
Setting
Code
Lengths
Via
Commands
on Length
page
A-7.
Setlength
Lengths
39
The
offor
a Code
code
refers
to the
number
ofSerial
characters
(i.e.,
human
readable
characters),
includingTo
check
digit(s) via
theserial
code
Code
39 Full
ASCII
is
enabled,
Length
Within
a Range
or Any
are the
preferred options.
set lengths
contains.
Lengths
for
Code
39
may
be
set
for
any
length,
one
or
two
discrete
lengths,
or
lengths
within
a
specific
range.
If
commands,
Parameter #see
L1 =Setting
12h L2 =Code
13h Lengths Via Serial Commands on page A-7.
Code 39NOTE
Full ASCII
is
enabled,
Length
Within
a
Range
or
Any
Length
are
the
preferred
options.
To
set
lengths
via
serial
When
setting
digit numbers
must
always
be preceded
by acheck
leading
zero.
The length of a code
refers
to thelengths,
numbersingle
of characters
(i.e., human
readable
characters),
including
digit(s)
the code contains. Lengths for Code
commands,
see
Setting
Code
Lengths
Via
Serial
Commands
on
page
A-7.
NOTE When setting lengths, single digit numbers must always be preceded by a leading zero.
39 may be set for any length, one or two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled, Length Within a Range or
One
- This
option limits decodes to only those Code 39 symbols containing a selected length. Lengths
AnyDiscrete
Length are Length
the preferred
options.
NOTE from
When
setting
lengths,
single beginning
numbers
must
always
be
byto
a leading
are
selected
the
numeric
bar codes
page
4-73.
Forpreceded
example,
decodezero.
only
Code 39 length.
symbols
with 14
One Discrete Length - This option
limits digit
decodes
toononly
those
Code
39 symbols
containing
a selected
Lengths
characters,
scan
Code
39
One
Discrete
Length,
then
scan
1
followed
by
4.
To
change
the
selection
or
cancel
an 14
NOTE:
When
setting
lengths,
single
digit
numbers
must
always
be
preceded
by
a
leading
zero.
are selected from the numeric bar codes beginning on page 4-73. For example, to decode only Code 39 symbols with
incorrect
entry,
scan
Cancel
on
page
4-74.
One Discrete
Length
This
option
limits decodes
onlyscan
those
Code 39by
symbols
containing
selected or
length.
Lengths
characters,
scan
Code-39
- One
Discrete
Length,to
then
1 followed
4. To change
the aselection
cancel
an
One
Discrete
Length
- This
option on
limits
decodes
to only thoseon
Code
39 symbols
containing
a selected
length. Lengths
are selected
from the with
numeric
are
selected
from
the
numeric
bar
codes
beginning
page
4-73. For
example,
to decode
only Code
39 symbols
14
incorrect
entry,
scan
Cancel
page
4-74.
bar codes beginning
on page3956.- For
example,
to decode
only Code
symbols
with 14 characters,
Code the
39 - selection
One DiscreteorLength,
thenan
scan
characters,
scan Code
One
Discrete
Length,
then 39
scan
1 followed
by 4. To scan
change
cancel
incorrect
Cancel
on page
4-74.
1 followedentry,
by 4. Toscan
change
the selection
or cancel
an incorrect entry, scan Cancel.
Code 39 - One Discrete Length
Code 39 - One Discrete Length
Two Discrete Lengths - This option limits decodes to only those Code 39 symbols containing either of two selected
lengths.
Lengths
are selected
thelimits
numeric
bar codes
beginning
on page
4-73. For containing
example, toeither
decode
onlyselected
those
Two Discrete
Lengths
- Thisfrom
option
decodes
only
those Code
39 symbols
of two
Code
39 -to
One
Discrete
Length
Code
39
symbols
containing
either
2
or
14
characters,
select
Code
39
Two
Discrete
Lengths,
then
scan
0,
2,
1, and
lengths. Lengths are selected from the numeric bar codes beginning on page 4-73. For example, to decode only those
then
4.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page
4-74.
Two Discrete
Lengths
- This
option
decodes to
onlyCode
those39
Code
39 Discrete
symbols containing
eitherscan
of two
selected
Code
39 symbols
containing
either
2 orlimits
14 characters,
select
- Two
Lengths, then
0, 2,
1, and
Two Discrete Lengths - This option limits decodes to only those Code 39 symbols containing either of two selected lengths. Lengths are selected from
lengths.
Lengths
arethe
selected
fromorthe
numeric
bar codesentry,
beginning
page on
4-73.
For4-74.
example, to decode only those
then
4. To
change
selection
cancel
an incorrect
scanon
Cancel
page
the numeric
bar codes
beginning on
page 56.
to decode
only Code
those Code
symbols
containingLengths,
either 2 or 14
characters,
select
Code
39 symbols
containing
either
2 orFor14example,
characters,
select
39 -39Two
Discrete
then
scan 0,
2, Code
1, and
39
Two
Discrete
Lengths,
then
scan
0,
2,
1,
and
then
4.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page
57.
then 4. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 39 - Two Discrete Lengths
Code 39 - Two Discrete Lengths
Length Within Range - This option limits decodes to only those Code 39 symbols within a specified range. For
example,
to decode
Code
39 option
symbols
containing
between
4 and 12
characters,
first within
scan Code
39 - Length
Within
Length Within
Range
- This
limits
decodes
onlyDiscrete
those
Code
39 symbols
a specified
range.
For
Code
39 -toTwo
Lengths
Range. Then
scan 0, Code
4, 1, and
Numeric
bar codes
begin on
page
To change
selection
or-cancel
anWithin
incorrect
example,
to decode
39 2.
symbols
containing
between
4 and
124-73.
characters,
first the
scan
Code 39
Length
entry,
scan
Cancel
on
page
4-74.
Length
Within
Range
- This
option
limitsbar
decodes
only on
those
Code
within
a specified
range.
For
Range.
Then
scan
0, 4,
1,
and
2.
Numeric
codes to
begin
page
4-73.39Tosymbols
change the
selection
or cancel
an incorrect
Length Within Range - This option limits decodes to only those Code 39 symbols within a specified range. For example, to decode Code 39 symbols
example,
decode
39 symbols containing between 4 and 12 characters, first scan Code 39 - Length Within
entry,
scantoCancel
onCode
page 4-74.
containing between 4 and 12 characters, first scan Code 39 - Length Within Range. Then scan 0, 4, 1, and 2. Numeric bar codes begin on page 56.
Range. Then scan 0, 4, 1, and 2. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect
To change
selection
cancel4-74.
an incorrect entry, scan Cancel on page 57.
entry,
scanthe
Cancel
onorpage
Code 39 - Length Within Range
Code 39 - Length Within Range
Any Length - Scan this option to decode Code 39 symbols containing any number of characters.
Any Length - Scan this option to decode Code
39 39
symbols
containing
number of characters.
Code
- Length
Within any
Range
Any Length - Scan this option to decode Code 39 symbols containing any number of characters.
Any Length - Scan this option to decode Code 39 symbols containing any number of characters.
Code 39 - Any Length
Code 39 - Any Length
Code 39 - Any Length
Barcode scanner configuration guide
31
withParameter
specified check
digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded. Only
# 30h
Code 39 Check
Digit Verification
enable this feature if your Code 39 symbols contain a module 43 check digit.
When this feature is enabled, the scan engine checks the integrity of all Code 39 symbols to verify that the data complies
Parameter
# Verification
30h
Code
39 Checkcheck
Digit
with
specified
digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded. Only
enable
this
feature
if
your Code
symbols
contain
a module
43 check
Parameter
# 30h is enabled,
When
this feature
the39scan
engine
checks
the integrity
of all digit.
Code 39 symbols to verify that the data complies
with
specified
check
digit algorithm.
Only
those
Code 39
modulo
checkwith
digitspecified
are decoded.
When
this feature
is enabled,
the scan engine
checks
the integrity
of symbols
all Code 39which
symbolsinclude
to verifyathat
the data43
complies
check digitOnly
enable
thisOnly
feature
your39Code
39which
symbols
module
43 are
check
digit.Only enable this feature if your Code 39 symbols contain
algorithm.
those ifCode
symbols
includecontain
a moduloa43
check digit
decoded.
a module 43 check digit.
Verify Code 39 Check Digit
(01h)
Verify Code 39 Check Digit
(01h)
Verify Code 39 Check Digit
(01h)
*Do Not Verify Code 39 Check Digit
(00h)
39 Check Digit
Transmit Code 39 Check Digit*Do Not Verify Code
(00h)
*Do Not Verify Code 39 Check Digit
Parameter # 2Bh
(00h)
Transmit Code 39 Check Digit
Scan this symbol to transmit the check digit with the data.
Parameter # 2Bh
Transmit
39 Check
Transmit
Code 39Code
Check Digit
Digit
Scan
this symbol to transmit the check digit with the data.
Parameter # 2Bh
Parameter # 2Bh
Scan this symbol to transmit the check digit with the data.
Scan this symbol to transmit the check digit with the data.
Transmit Code 39 Check Digit (Enable)
(01h)
Transmit Code 39 Check Digit (Enable)
Scan this symbol to transmit data without the check digit. (01h)
Transmit Code 39 Check Digit (Enable)
(01h)
Scan this symbol to transmit data without the check digit.
Scan this symbol to transmit data without the check digit.
Scan this symbol to transmit data without the check digit.
*Do Not Transmit Code 39 Check Digit (Disable)
(00h)
*Do Not Transmit Code 39 Check Digit (Disable)
(00h)
*Do Not Transmit Code 39 Check Digit (Disable)
(00h)
32
Barcode scanner configuration guide
Enable/Disable Code 39 Full ASCII
Parameter
11h
Enable/Disable
Code#39
Full ASCII
Parameter
# 11h
Code
39 Full
ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or
disable
Code
39 Full
ASCII,
thewhich
appropriate
bar code
below.
Code 39
Full ASCII
is a variant
of scan
Code 39
pairs characters
to encode
the full ASCII character set. To enable or disable Code 39 Full ASCII, scan
the appropriate bar code below.
Enable Code 39 Full ASCII
(00h)
*Disable Code 39 Full ASCII
(00h)
NOTE: Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If the Enable Trioptic Code 39 setting is not accepted*, disable
Code 39 Full ASCII and try again.
NOTE Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If the Enable Trioptic Code
39 setting is not accepted*, disable Code 39 Full ASCII and try again.
*An SSI parameter entry error, event ID 07h, is sent to the host if packeted data communication is enabled to inform the user that the parameter
change was not accepted.
*An SSI parameter entry error, event ID 07h, is sent to the host if packeted data communication is
enabled to inform the user that the parameter change was not accepted.
Barcode scanner configuration guide
33
Code 93
6Enable/Disable
Code 93 Code 93
Parameter # 09h
Enable/Disable Code 93
ToParameter
enable or
disable Code 93, scan the appropriate bar code below.
# 09h
To enable or disable Code 93, scan the appropriate bar code below.
Enable Code 93
(01h)
*Disable Code 93
(00h)
Set Lengths for Code 93
Parameter # L1 = 1Ah L2 = 1Bh
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
Code 93 One Discrete Length, then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - One Discrete Length
34
Barcode scanner configuration guide
Set Lengths for Code 93
Parameter # L1 = 1Ah L2 = 1Bh
Set Lengths for Code 93
The
length #
ofL1
a code
to the number of characters (i.e., human readable characters), including check digit(s) the code
Parameter
= 1Ah refers
L2 = 1Bh
contains.
Lengths
for
Code
93number
may be
set for any
one or characters),
two discrete
lengths,
lengths
within
a specific
To
The length of a code refers to the
of characters
(i.e.,length,
human readable
including
checkor
digit(s)
the code
contains.
Lengthsrange.
for Code
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page A-7.
93 may be set for any length, one or two discrete lengths, or lengths within a specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
One Discrete
- Select
this option
to decode
codesthe
containing
a selected
length.
For 93
example,
selectcontaining
Code 93 One
Length,
Code
93 OneLength
Discrete
Length,
then
scan only
1, 4,those
to limit
decoding
to only
Code
symbols
14Discrete
characters.
4Numeric
-then
42 scanSE655
Decoded
Linear
Imaging
Engine
1,
4,
to
limit
the
decoding
to
only
Code
93
symbols
containing
14
characters.
Numeric
bar
codes
begin
on
page
56.
To
change
the
bar codes
begin Linear
on pageImaging
4-73. ToEngine
change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
4 - 42 SE655
Decoded
selection or cancel an incorrect entry, scan Cancel on page 57.
4 - 42 SE655 Decoded Linear Imaging Engine
Set Lengths for Code 93 (continued)
Set Lengths for Code 93 (continued)
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
Lengths
for Code
(continued)
TwoSet
Discrete
Lengths
- Select93
this
option to decode only those codes containing two selected lengths. For example,
select Code 93 Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
select
Code
93 Two Discrete
Lengths,
then
scan
2,
1, Discrete
4,
limitLength
the
decoding
tooronly
Code
93
symbols
containing
2 or 14
characters.
Numeric
bar
codes
begin
on
page
4-73.
Toto
change
the
selection
cancel
an
incorrect
scan
Code
930,-only
One
Two
Discrete
Lengths
- Select
this
option
to
decode
those
codes
containing
two
selected
lengths.
Forentry,
example,
2
or
14
characters.
Numeric
bar
codes
begin
on
page
4-73.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
CancelCode
on page
4-74.Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing
select
93 Two
Cancel
on page
4-74.
Two
Discrete
Lengths
Select
this
option
to
decode
only
those
codes
containing
two
selected
lengths.
For
example,
select
Code
93
Two
Discrete
2 or 14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan
Lengths,on
then
scan4-74.
0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing 2 or 14 characters. Numeric bar codes begin on page 56. To
Cancel
page
change the selection or cancel an incorrect entry, scan Cancel on page 57.
Code 93 - Two Discrete Lengths
Code 93 - Two Discrete Lengths
Length Within Range - This option sets the unit to decode a code type within a specified range. For example, to
Code
93to- 12
Two
Discrete
Lengths
Length Code
Within93Range
- This
option sets
the
unit
decode
a code
type
within
specified
example,
to
decode
symbols
containing
between
4 and
characters,
first
scan
Codea 93
Length range.
Within For
Range,
then scan
decode
Code
93 symbols
containing
between
4 and
12 characters,
firstzero).
scan Code
93 Length
Within
Range,
then
scan
0,
4,
1
and
2
(single
digit
numbers
must
always
be
preceded
by
a
leading
Numeric
bar
codes
begin
on
page
4-73.
Length
Within
Range
- Thissets
option
the unit
totype
decode
a code type
within
a specified
range.93For
example,
toTo
Within
Range
- digit
This option
the
unitsets
to decode
a code
within
range.
example,
to decode
containing
0, Length
4, 1 and
2selection
(single
numbers
must
always
be
preceded
by on
aa specified
leading
zero).For
Numeric
bar
codesCode
begin symbols
on page
4-73. To
change
the
or
cancel
an
incorrect
entry,
scan
Cancel
page
4-74.
decode
Code
93 symbolsfirst
containing
betweenWithin
4 andRange,
12 characters,
firstand
scan
Code 93 Length Within Range, then scan
betweenthe
4 and
12 characters,
93 Length
then scan
0, 4, 1 4-74.
2 (single digit numbers must always be preceded by a
change
selection
or cancelscan
anCode
incorrect
entry, scan
Cancel
on page
0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To
leading zero). Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57:
change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Code 93 - Length Within Range
Code 93 - Length Within Range
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Code 93
- Length
Within any
Range
Any
- Scan
this option
to decode
symbols
number of characters.
AnyLength
Length - Scan
this option
to decode
Code 93 Code
symbols93
containing
anycontaining
number of characters.
Any Length - Scan this option to decode Code 93 symbols containing any number of characters.
Code 93 - Any Length
Code 93 - Any Length
Code 93 - Any Length
Barcode scanner configuration guide
35
Code 11
7Enable/Disable
Code 11 Code 11
Parameter # 0Ah
Enable/Disable Code 11
ToParameter
enable or
disable Code 11, scan the appropriate bar code below.
# 0Ah
To enable or disable Code 11, scan the appropriate bar code below.
Enable Code 11
(01h)
*Disable Code 11
(00h)
Set Lengths for Code 11
Parameter # L1 = 1Ch L2 = 1Dh
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within a specific range.
• One Discrete Length - Select this option to decode only Code 11 symbols containing a selected length. Select the
length using the numeric bar codes beginning on page 4-73. For example, to decode only Code 11 symbols with 14
characters, scan Code 11 - One Discrete Length, then scan 1 followed by 4. To correct an error or to change the
selection, scan Cancel on page 4-74.
• Two Discrete Lengths - Select this option to decode only Code 11 symbols containing either of two selected
lengths. Select lengths using the numeric bar codes beginning on page 4-73. For example, to decode only those
Code 11 symbols containing either 2 or 14 characters, select Code 11 - Two Discrete Lengths, then scan 0, 2, 1,
and then 4. To correct an error or to change the selection, scan Cancel on page 4-74.
• Length Within Range - Select this option to decode a Code 11 symbol with a specific length range. Select
lengths using numeric bar codes beginning on page 4-73. For example, to decode Code 11 symbols containing
between 4 and 12 characters, first scan Code 11 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit
numbers must always be preceded by a leading zero). To correct an error or change the selection, scan Cancel
on page 4-74.
• Any Length - Scan this option to decode Code 11 symbols containing any number of characters within the scan
engine capability.
36
Barcode scanner configuration guide
Set Lengths for Code 11
Parameter # L1 = 1Ch L2 = 1Dh
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for
Code 11 to any length, one or two discrete lengths, or lengths within a specific range.
• One Discrete Length - Select this option to decode only Code 11 symbols containing a selected length. Select the length using the numeric bar
codes beginning on page 56. For example, to decode only Code 11 symbols with 14 characters, scan Code 11 - One Discrete Length, then scan 1
followed by 4. To correct an error or to change the selection, scan Cancel on page 57.
• Two Discrete Lengths - Select this option to decode only Code 11 symbols containing either of two selected lengths. Select lengths using the
numeric bar codes beginning on page 56. For example, to decode only those Code 11 symbols containing either 2 or 14 characters, select Code
11 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To correct an error or to change the selection, scan Cancel on page 57.
4 - 44
SE655 Decoded Linear Imaging Engine
• Length Within Range - Select this option to decode a Code 11 symbol with a specific length range. Select lengths using numeric bar codes beginning
on page 56. For example, to decode Code 11 symbols containing between 4 and 12 characters, first scan Code 11 - Length Within Range. Then
scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). To correct an error or change the selection, scan Cancel on
Set57.Lengths for Code 11 (continued)
page
• Any Length - Scan this option to decode Code 11 symbols containing any number of characters within the scan engine capability.
Code 11 - One Discrete Length
Code 11 - Two Discrete Lengths
Code 11 - Length Within Range
Code 11 - Any Length
Barcode scanner configuration guide
37
Code 11 Check Digit Verification
Code 11 Check Digit Verification
Parameter # 34h
Parameter # 34h
This
allows
check
the
all Code
11 symbols
to verify
that
complies
with the
Thisfeature
feature allows
thethe
scanscan
engineengine
to checktothe
integrity
of integrity
all Code 11ofsymbols
to verify
that the data
complies
withthe
the data
specified
check digit
specified
check
digit
algorithm.
This
selects
the
check
digit
mechanism
for
the
decoded
Code
11
bar
code.
The
options
algorithm. This selects the check digit mechanism for the decoded Code 11 bar code. The options are to check for one check digit, check for two are
to check
check
for one check digit, check for two check digits, or disable the feature.
digits, or disable the feature.
To enable this feature, scan the bar code below corresponding to the number of check digits encoded in your Code 11
To enable this feature, scan the bar code below corresponding to the number of check digits encoded in your Code 11 symbols.
symbols.
*Disable
(00h)
One Check Digit
(01h)
4 - 46 SE655 Decoded Linear Imaging Engine
Transmit Code 11 Check Digits
Two Check Digits
(02h)
Parameter # 2Fh
Transmit Code 11 Check Digits
This
feature# selects
whether or not to transmit the Code 11 check digit(s).
Parameter
2Fh
This feature selects whether or not to transmit the Code 11 check digit(s).
Transmit Code 11 Check Digit(s) (Enable)
(01h)
*Do Not Transmit Code 11 Check Digit(s) (Disable)
(00h)
NOTE: Code 11 Check Digit Verification must be enabled for this parameter to function.
NOTE
38
Code 11 Check Digit Verification must be enabled for this parameter to function.
Barcode scanner configuration guide
Parameter # 06h
Interleaved 2 of 5
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
8Enable/Disable
InterleavedInterleaved
2 of 5 2 of 5
Parameter # 06h
Enable/Disable Interleaved 2 of 5
ToParameter
enable or
disable Interleaved 2 of 5, scan the appropriate bar code below.
# 06h
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.
*Enable Interleaved 2 of 5
(01h)
*Enable Interleaved 2 of 5
(01h)
Disable Interleaved 2 of 5
(00h)
Set Lengths for Interleaved 2 of 5
Disable Interleaved 2 of 5
(00h)
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
Set Lengths for Interleaved 2 of 5
contains.
Lengths forfor
I 2 Interleaved
of 5 may be set2for
Set Lengths
ofany
5 length, one or two discrete lengths, or lengths within a specific range. To
setParameter
lengths #via
commands,
see Setting Code Lengths Via Serial Commands on page B-8.
L1serial
= 16h L2
= 17h
Parameter # L1 = 16h L2 = 17h
The
length of a code#refers
number
characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for I 2 of
Parameter
L1 to
= the
16h
L2 =of17h
5 may be
set for any
length,
one or
two discrete
or lengthsmust
withinalways
a specific
NOTE
When
setting
lengths,
singlelengths,
digit numbers
berange.
preceded by a leading zero.
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
NOTE: When
settingfor
lengths,
digit be
numbers
must
always
be preceded
a leading
zero.lengths, or lengths within a specific range. To
contains.
Lengths
I 2 ofsingle
5 may
set for
any
length,
one or by
two
discrete
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select I 2
set lengths via serial commands, see Setting Code Lengths Via Serial Commands on page B-8.
ofOne
5 One
Discrete
1, 4, only
to decode
only
I 2 of 5a symbols
containing
14 characters.
barLength,
codes
Discrete
Length -Length,
Select thisthen
optionscan
to decode
those codes
containing
selected length.
For example,
select I 2 of 5Numeric
One Discrete
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an
NOTE When setting lengths, single digit numbers must always be preceded by a leading zero.
incorrect entry, scan Cancel on page 57.
4One
- 48Discrete
SE655Length
Decoded
Linear Imaging Engine
- Select this option to decode only those codes containing a selected length. For example, select I 2
of 5 One Discrete Length, then scan 1, 4, to decode only I 2 of 5 symbols containing 14 characters. Numeric bar codes
begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Set Lengths for Interleaved 2 of 5 (continued)
I 2 of 5 - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
select
I 2 of 5Lengths
Two Discrete
then scan
0, 6,codes
1, 4,containing
to decode
I 2lengths.
of 5 symbols
containing
6 5orTwo
14 Discrete
characters.
Two Discrete
- Select thisLengths,
option to decode
only those
two only
selected
For example,
select I 2 of
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters. Numeric bar codes begin on page 56. To change the
selection or cancel an incorrect entry, scan Cancel on page 57.
I 2 of 5 - One Discrete Length
I 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
selection or cancel an incorrect entry, scan Cancel on page 4-74.
Barcode scanner configuration guide
I 2 of 5 - Length Within Range
39
digit numbers must always be preceded by a leading zero). Numeric bar codes begin on page 4-73. To change the
Length Within Range - Select this option to decode only codes within a specified range. For example, to decode I 2 of 5
selection or cancel an incorrect entry, scan Cancel on page 4-74.
symbols containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit
numbers
must -always
beoption
preceded
by only
a leading
zero).
Numeric
barFor
codes
begin
on page
To change
Length
Within Range
Select this
to decode
codes within
a specified
range.
example,
to decode
I 2 of4-73.
5 symbols
containingthe
between
selection or cancel an incorrect entry, scan Cancel on page 4-74.
4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero).
Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
I 2 of 5 - Length Within Range
Any Length - Scan this option to decode I 2 of 5 symbols containing any number of characters.
I 2 of 5 - Length Within Range
NOTE - Scan
Selecting
option
may leadI 2
to of
misdecodes
for I 2 of 5 codes.
Any
this this
option
to decode
5 symbols
any number of characters.
AnyLength
Length - Scan
this option
to decode
I 2 of 5 symbols
containing
anycontaining
number of characters.
NOTE: Selecting
this option this
may option
lead to misdecodes
I 2 of 5 codes.
NOTE Selecting
may lead toformisdecodes
for I 2 of 5 codes.
Parameter Menus 4 - 49
I 2 of 5 Check Digit Verification
Parameter # 31h
I 2 of 5 Check Digit Verification
I 2 of 5 - Any Length
I 2 of 5 - Any Length
When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm,
Parameter # 31h
either USS (Uniform Symbology Specification), or OPCC (Optical Product Code Council).
When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm, either USS (Uniform
Symbology Specification), or OPCC (Optical Product Code Council).
*Disable
(00h)
USS Check Digit
(01h)
OPCC Check Digit
(02h)
Transmit I 2 of 5 Check Digit
Parameter # 2Ch
Scan this symbol to transmit the check digit with the data.
40
Transmit I 2 of 5 Check Digit (Enable)
(01h)
Barcode scanner configuration guide
Transmit I 2 of 5 Check Digit
Transmit I 2 of 5 Check Digit
Parameter # 2Ch
Transmit I 2 of 5 Check Digit
Parameter # 2Ch
Scan this symbol to transmit the check digit with the data.
Parameter # 2Ch
Scan this
this symbol
to transmit
the check
digit withdigit
the data.
Scan
symbol
to transmit
the check
with the data.
Transmit I 2 of 5 Check Digit (Enable)
Transmit I 2 of 5(01h)
Check Digit (Enable)
Scan this symbol to transmit data without the check digit. (01h)
Scan
symbol
to transmit
data without
the
check digit.
Scan this
this symbol
to transmit
data without
the check
digit.
4 - 50 SE655 Decoded Linear Imaging Engine
Convert I 2 of 5 to EAN-13*Do Not Transmit I 2 of 5 Check Digit (Disable)
Parameter # 52h
*Do Not Transmit I 2 (00h)
of 5 Check Digit (Disable)
(00h)
Convert
I 2 of 5 converts
to EAN-13a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. To accomplish this,
This
parameter
I 2Parameter
of 5 must
be enabled, one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check
# 52h
digit.
This parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. To accomplish this, I 2 of 5 must be enabled,
one length must be set to 14, and the code must have a leading zero and a valid EAN-13 check digit.
Convert I 2 of 5 to EAN-13 (Enable)
(01h)
*Do Not Convert I 2 of 5 to EAN-13 (Disable)
(00h)
Barcode scanner configuration guide
41
Discrete 2 of 5
Enable/Disable Discrete 2 of 5
Discrete 2 of 5
Enable/Disable
Parameter # 05hDiscrete 2 of 5
9Enable/Disable
Discrete
2 Discrete
of 5 2 of 5
Parameter
# 05h
To enable
or disable
Discrete 2 of 5, scan the appropriate bar code below.
Parameter
# 05h
To enable
or disable
Discrete 2 of 5, scan the appropriate bar code below.
Enable/Disable Discrete 2 of 5
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Parameter # 05h
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.
Enable Discrete 2 of 5
(01h)
Enable Discrete 2 of 5
(01h)
Enable Discrete 2 of 5
(01h)
Set Lengths for Discrete 2 of 5
*Disable Discrete 2 of 5
(00h)
*Disable Discrete 2 of 5
(00h)
*Disable Discrete 2 of 5
(00h)
Set
Lengths# for
of 5
Parameter
L1 =Discrete
14h L2 =215h
Lengths
Discrete
of 5
SetSet
Lengths
2=
of
514h L2 =215h
Parameter
# for
L1
The
length
offora Discrete
code
refers
to the number of characters (i.e., human readable characters), including check digit(s) the code
contains.
forL2
D =2 15h
5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
ParameterLengths
# L1 = 14h
Parameter
# L1
=of14h
L2see
= 15h
Thelengths
length of
a serial
code
refers
to the
number
of characters
(i.e., Via
human
readable
characters),
including check digit(s) the code
set
via
commands,
Code
Lengths
Serial
Commands
on page
The length of a code refers to the number
ofSetting
characters
(i.e., human
readable characters),
including check
digit(s)A-7.
the code contains. Lengths for D 2
contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. To
The
length
of
a
code
refers
to
the
number
of
characters
(i.e.,
human
readable
characters),
including
digit(s) the
code
of
5
may
be
set
for
any
length,
one
or
two
discrete
lengths,
or
lengths
within
a
specific
range.
One
Discrete
- Select thissee
option
to decode
only those
selected
length. check
For example,
select
D
set lengths
via Length
serial commands,
Setting
Code Lengths
Via codes
Serial containing
Commandsa on
page A-7.
contains.
Lengths
for
D
2
of
5
may
be
set
for
any
length,
one
or
two
discrete
lengths,
or
lengths
within
a
specific
range.
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar To
One
Discrete
Length
- Select
this option
tooption
decode
only
those Lengths
codes
containing
a selected
length. For
example,
select
D 2 of
5 One
Discreteselect
Length,D
set
lengths
serial
see
Setting
Code
Viaan
Serial
Commands
on
page
A-7.
One
Discrete
Length
- Select
decode
only
those
codes
containing
selected
length.
For
example,
codes
beginviaon
pagecommands,
4-73.
To this
change
thetoselection
or cancel
incorrect
entry, a
scan
Cancel
on page
4-74.
then
scan
1,
4,
to
decode
only
D
2
of
5
symbols
containing
14
characters.
Numeric
bar
codes
begin
on
page
56.
To
change
the
selection
or
cancel
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select D
codes
beginentry,
on page
4-73.onTopage
change
the selection or cancel an incorrect entry, scan Cancel on page 4-74.
an incorrect
scan Cancel
57.
2 of 5 One Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric bar
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
D 2 of 5 - One Discrete Length
Two Discrete Lengths - Select this option toDdecode
codesLength
containing two selected lengths. For example,
2 of 5 -only
Onethose
Discrete
select D 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14
Ddecode
2those
of 5codes
-only
One
Discrete
Length
Two
Lengths
this
to
those
codes
containing
two
selected
lengths.
example,
TwoDiscrete
DiscreteNumeric
Lengths
- Select
this option
tooption
decode
only
containing
two
selected
lengths.
For example,
select
Dentry,
2 ofFor
5scan
Two
Discrete
characters.
bar- Select
codes
begin
on page
4-73.
To
change
the
selection
or cancel
an incorrect
Cancel on
select
D 2then
of scan
5 Two
Discrete
Lengths,
then
scancontaining
0, 2, 1, 24,orto14decode
only
D 2 bar
of 5codes
symbols
containing
2 or 14
page
4-74.
Lengths,
0,
2,
1,
4,
to
decode
only
D
2
of
5
symbols
characters.
Numeric
begin
on
page
56.
To
change
the
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
characters.
Numeric
bar
codes
begin
on
page
4-73.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
selection
an incorrect
entry,
scan Cancelthen
on page
57. 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14
select
D 2orofcancel
5 Two
Discrete
Lengths,
scan
page 4-74.
4 - 52 SE655
Decoded
Linear begin
Imaging
Engine
characters.
Numeric
bar codes
on page
4-73. To change the selection or cancel an incorrect entry, scan Cancel on
page 4-74.
Set Lengths for Discrete 2 of 5 (continued)
D 2 of 5 - Two Discrete Lengths
Length Within Range - Select this option to decode codes within a specified range. For example, to decode D 2 of 5
Length Within
Range -between
Select this 4
option
codes
specified
example,
to decode
D 2 ofthen
5 symbols
between
4
D 2 within
offirst
5 -ascan
Two
Discrete
Lengths
symbols
containing
and to
12decode
characters,
D
2range.
of 5 For
Length
Within
Range,
scancontaining
0, 4, 1 and
2 (single
andnumbers
12 characters,
firstbe
scan
D 2 of 5 Length
Range,
then scan 0, 4, 1bar
andcodes
2 (singlebegin
digit numbers must be preceded by a leading zero). Numeric
digit
must
preceded
by a Within
leading
Dzero).
2 of 5Numeric
- Two Discrete
Lengths on page 4-73. To change the selection or
bar codes
on page
56. Toscan
change
the selection
or cancel
an incorrect entry, scan Cancel on page 57.
cancel
an begin
incorrect
entry,
Cancel
on page
4-74.
D 2 of 5 - Length Within Range
Any
Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.
Any Length - Scan this option to decode D 2 of 5 symbols containing any number of characters.
42
NOTE
Selecting this option may lead to misdecodes for D 2 of 5 codes.
Barcode scanner configuration guide
NOTE
Selecting this option may lead to misdecodes for D 2 of 5 codes.
NOTE: Selecting this option may lead to misdecodes for D 2 of 5 codes.
D 2 of 5 - Any Length
Barcode scanner configuration guide
43
Chinese 2 of 5
10
Chinese 2 of
5 2 of 5
Enable/Disable
Chinese
Parameter # F0h 98h
Enable/Disable Chinese 2 of 5
ToParameter
enable or
disable
# F0h
98h Chinese 2 of 5, scan the appropriate bar code below.
To enable or disable Chinese 2 of 5, scan the appropriate bar code below.
Enable Chinese 2 of 5
(01h)
*Disable Chinese 2 of 5
(00h)
44
Barcode scanner configuration guide
Matrix 2 of 5
11
Matrix 2 ofMatrix
5
Enable/Disable
2 of 5
Parameter # F1h 6Ah
Enable/Disable Matrix 2 of 5
To enable or disable Matrix 2 of 5, scan the appropriate bar code below.
Parameter # F1h 6Ah
To enable or disable Matrix 2 of 5, scan the appropriate bar code below.
Enable Matrix 2 of 5
(01h)
*Disable Matrix 2 of 5
(00h)
Set Lengths for Matrix 2 of 5
Parameter # L1 = F1h 6Bh L2 = F1h 6Ch
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
contains. Set lengths for Matrix 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range.
• One Discrete Length - Select this option to decode only Matrix 2 of 5 symbols containing a selected length. Select
the length using the numeric bar codes beginning on page 4-73. For example, to decode only Matrix 2 of 5 symbols
with 14 characters, scan Matrix 2 of 5 - One Discrete Length, then scan 1 followed by 4. To correct an error or to
change the selection, scan Cancel on page 4-74.
• Two Discrete Lengths - Select this option to decode only Matrix 2 of 5 symbols containing either of two selected
lengths. Select lengths using the numeric bar codes beginning on page 4-73. For example, to decode only Matrix 2
of 5 symbols containing either 2 or 14 characters, select Matrix 2 of 5 - Two Discrete Lengths, then scan 0, 2, 1,
and then 4. To correct an error or to change the selection, scan Cancel on page 4-74.
• Length Within Range - Select this option to decode a Matrix 2 of 5 symbol with a specific length range. Select
lengths using the numeric bar codes beginning on page 4-73. For example, to decode Matrix 2 of 5 symbols
containing between 4 and 12 characters, first scan Matrix 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2
(enter a leading zero for single digit numbers). To correct an error or change the selection, scan Cancel on page
4-74.
• Any Length - Scan this option to decode Matrix 2 of 5 symbols containing any number of characters within the digital
scanner’s capability.
Barcode scanner configuration guide
45
Set Lengths for Matrix 2 of 5
Parameter # L1 = F1h 6Bh L2 = F1h 6Ch
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Set lengths for
Matrix 2 of 5 to any length, one or two discrete lengths, or lengths within a specific range.
• One Discrete Length - Select this option to decode only Matrix 2 of 5 symbols containing a selected length. Select the length using the numeric bar
codes beginning on page 56. For example, to decode only Matrix 2 of 5 symbols with 14 characters, scan Matrix 2 of 5 - One Discrete Length,
then scan 1 followed by 4. To correct an error or to change the selection, scan Cancel on page 57.
• Two Discrete Lengths - Select this option to decode only Matrix 2 of 5 symbols containing either of two selected lengths. Select lengths using the
numeric bar codes beginning on page 56. For example, to decode only Matrix 2 of 5 symbols containing either 2 or 14 characters, select Matrix 2
of 5 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To correct an error or to change the selection, scan Cancel
on page 57.Menus 4 - 55
Parameter
• Length Within Range - Select this option to decode a Matrix 2 of 5 symbol with a specific length range. Select lengths using the numeric bar codes
beginning on page 56. For example, to decode Matrix 2 of 5 symbols containing between 4 and 12 characters, first scan Matrix 2 of 5 - Length
Within Range. Then scan 0, 4, 1, and 2 (enter a leading zero for single digit numbers). To correct an error or change the selection, scan Cancel on
Set57.Lengths for Matrix 2 of 5 (continued)
page
• Any Length - Scan this option to decode Matrix 2 of 5 symbols containing any number of characters within the digital scanner’s capability.
*Matrix 2 of 5 - One Discrete Length
Matrix 2 of 5 - Two Discrete Lengths
Matrix 2 of 5 - Length Within Range
Matrix 2 of 5 - Any Length
Matrix 2 of 5 Redundancy
Parameter # F1h 6Dh
To enable or disable Matrix 2 of 5 redundancy, scan the appropriate bar code below.
Enable Matrix 2 of 5 Redundancy
(01h)
46
Barcode scanner configuration guide
edundancy
1h 6Dh
Matrix 2 of 5 Redundancy
Matrix 2 of 5 Redundancy
Parameter # F1h 6Dh
atrix 2 of 5 redundancy, scan the appropriate
below.
To enablebar
or code
disable
Matrix 2 of 5 redundancy, scan the appropriate bar code below.
Parameter # F1h 6Dh
To enable or disable Matrix 2 of 5 redundancy, scan the appropriate bar code below.
Matrix 2 of 5 Redundancy
(01h)
Enable Matrix 2 of 5 Redundancy
(01h)
4 - 56 SE655 Decoded Linear Imaging Engine
4 - 56 SE655 Decoded Linear Imaging Engine
Matrix 2 of 5 Check Digit
Parameter
6EhDigit
Matrix 2 of #5 F1h
Check
*Disable Matrix 2 of 5 Redundancy
(00h)
*Disable Matrix 2 of 5 Red
(00h)
The Parameter
check digit is the
last 6Eh
character of the symbol used to verify the integrity of the data. Scan the appropriate bar code
# F1h
Matrixto2transmit
of 5 Checkthe
Digit
below
bar code data with or without the Matrix 2 of 5 check digit.
The
check digit
the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code
Parameter
# F1his6Eh
below
to
transmit
the
codeofdata
with orused
without
the
ofthe
5 check
digit.
The check digit is the lastbar
character
the symbol
to verify
theMatrix
integrity2 of
data. Scan
the appropriate bar code below to transmit the bar
code data with or without the Matrix 2 of 5 check digit.
Enable Matrix 2 of 5 Check Digit
(01h)
Enable Matrix 2 of 5 Check Digit
(01h)
*Disable Matrix 2 of 5 Check Digit
(00h)
*Disable Matrix 2 of 5 Check Digit
Transmit Matrix 2 of 5 Check Digit
(00h)
Parameter # F1h 6Fh Check Digit
Transmit
of 5
Transmit
Matrix 2Matrix
of 5 Check2Digit
Scan
a bar #code
below
transmit Matrix 2 of 5 data with or without the check digit.
Parameter
F1h 6Fh
Parameter
# F1hto 6Fh
Scan a bar code below to transmit Matrix 2 of 5 data with or without the check digit.
Scan a bar code below to transmit Matrix 2 of 5 data with or without the check digit.
Transmit Matrix 2 of 5 Check Digit
(01h)
Transmit Matrix 2 of 5 Check Digit
(01h)
*Do Not Transmit Matrix 2 of 5 Check Digit
(00h)
*Do Not Transmit Matrix 2 of 5 Check Digit
(00h)
Barcode scanner configuration guide
47
Inverse 1D
Parameter # F1h 4Ah
12 Inverse 1D
This parameter sets the 1D inverse decoder setting. Options are:
• Regular
Only
Parameter
# F1h
4Ah- the digital scanner decodes regular 1D bar codes only.
This
sets the
1D digital
inverse decoder
Options
are: 1D bar codes only.
• parameter
Inverse Only
- the
scannersetting.
decodes
inverse
• Regular Only - the digital scanner decodes regular 1D bar codes only.
• Inverse Autodetect - the digital scanner decodes both regular and inverse 1D bar codes.
• Inverse Only - the digital scanner decodes inverse 1D bar codes only.
• Inverse Autodetect - the digital scanner decodes both regular and inverse 1D bar codes.
*Regular
(00h
Inverse Only
(01h)
Inverse Autodetect
(02h)
48
Barcode scanner configuration guide
Enable/Disable Codabar
Codabar
Parameter
# 07h
13
Codabar
Enable/Disable Codabar
To enable or disable Codabar, scan the appropriate bar code below.
Parameter # 07h
Enable/Disable Codabar
ToParameter
enable or
disable Codabar, scan the appropriate bar code below.
# 07h
To enable or disable Codabar, scan the appropriate bar code below.
Enable Codabar
(01h)
Enable Codabar
(01h)
*Disable Codabar
(00h)
Set Lengths for Codabar
*Disable Codabar
(00h)
Parameter # L1 = 18h L2 = 19h
Lengths
for Codabar
SetSet
Lengths
for Codabar
The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code
Parameter
# L1 = 18h
L2
==19h
contains.
Lengths
for
Codabar
set for any length, one or two discrete lengths, or lengths within a specific range. To
Parameter
# L1
18hmay
L2 =be19h
setThe
lengths
via
serial
commands,
seeofSetting
Code
Lengths
Via characters),
Serial Commands
on page
length of
a code
refers
to the number
characters
(i.e., human
readable
including check
digit(s)A-7.
the code contains. Lengths for
The
length
of be
a code
to the
of characters
(i.e., human
characters), including check digit(s) the code
Codabar
may
set for refers
any length,
one number
or two discrete
lengths, or lengths
within a readable
specific range.
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. To
Codabar
OneLength
Discrete
Length,
then
scan only
1, 4,those
to decode
only Codabar
symbols
containing
14 characters. Numeric bar
Discrete
- Select
this optionsee
to decode
codes containing
a selected
length. For on
example,
setOne
lengths
via serial
commands,
Setting
Code Lengths
Via Serial
Commands
pageselect
A-7.Codabar One Discrete Length,
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel
One Discrete Length - Select this option to decode only those codes containing a selected length. For example, select
an incorrect entry, scan Cancel on page 57.
Codabar One Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14
characters.Menus
Numeric4bar
Parameter
- 59
codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel on page 4-74.
Parameter Menus 4 - 59
Codabar (continued)
Codabar - One Discrete Length
Two
Lengths
This option
setstothe
unitonly
to decode
only
those codes
containing
twoexample,
selected
lengths.
TwoDiscrete
Discrete (continued)
Lengths
- This-option
sets the unit
decode
those codes
containing
two selected
lengths. For
select
CodabarFor
Two
Codabar
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar
symbols
containing
6 orLength
14 characters. Numeric bar codes begin on page 56. To
Codabar
- One
Discrete
14change
characters.
Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel
the selection or cancel an incorrect entry, scan Cancel on page 57.
on
page
4-74. Lengths - This option sets the unit to decode only those codes containing two selected lengths. For
Two
Discrete
example, select Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or
14 characters. Numeric bar codes begin on page 4-73. To change the selection or cancel an incorrect entry, scan Cancel
Codabar - Two Discrete Lengths
on page 4-74.
Length Within Range - Select this option to decode a code within a specified range. For example, to decode Codabar
Codabar - Two Discrete Lengths
symbols containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
(single
digit
numbers
mustSelect
always
be
preceded
by
a leading
zero).
Numeric
bartocodes
begin
on symbols
page 4-73.
To change
the
Length
Within
Range
option
to decode
a code
within
specified
range.
For example,
to decode
Codabar
Length Within
Range
- Select- this
optionthis
to decode
a code
within a specified
range.
Foraexample,
decode
Codabar
containing
between
4
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page
4-74.
symbols
containing
4 and
12Within
characters,
firstscan
scan
Length
Withinmust
Range,
scan 0,by4,a leading
1 andzero).
2
and 12 characters,
firstbetween
scan Codabar
Length
Range, then
0, 4,Codabar
1 and 2 (single
digit numbers
alwaysthen
be preceded
(single
digit
numbers
must
always
be
preceded
by
a
leading
zero).
Numeric
bar
codes
begin
on
page
4-73.
To
change
the
Numeric bar codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
selection or cancel an incorrect entry, scan Cancel on page 4-74.
Codabar - Length Within Range
Any
- Scan
this option
to decode
symbols
any number of characters.
AnyLength
Length - Scan
this option
to decode
Codabar Codabar
symbols containing
any containing
number of characters.
Codabar - Length Within Range
Any
Length
- Scan
this option
to decode Codabar symbols containing any number of characters.
Barcode
scanner
configuration
guide
49
Any
- Scan
this option
decode Codabar
4 - 60Length
SE655
Decoded
LineartoImaging
Engine symbols containing any number of characters.
4 - 60 SE655 Decoded Linear Imaging Engine
CLSI Editing
Parameter
CLSI Editing# 36h
Codabar - Any Length
When
enabled, this# parameter
strips the start and stop characters and inserts a space after the first, fifth, and tenth
Parameter
36h
characters of a 14-character Codabar symbol.
CLSI Editing
When
enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth
characters
of36h
a Symbol
14-character
Codabar
symbol.
NOTE
length does
not include
start and stop characters.
Parameter
#
When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character
CodabarNOTE
symbol.Symbol length does not include start and stop characters.
NOTE: Symbol length does not include start and stop characters.
Enable CLSI Editing
(01h)
Enable CLSI Editing
(01h)
NOTIS Editing
*Disable CLSI Editing
(00h)
*Disable CLSI Editing
(00h)
Parameter
# 37h
NOTIS Editing
NOTIS Editing
When
enabled,
strips the start and stop characters from decoded Codabar symbol.
Parameter
# 37hthis# parameter
Parameter
37h
When enabled, this parameter strips the start and stop characters from decoded Codabar symbol.
When enabled, this parameter strips the start and stop characters from decoded Codabar symbol.
Enable NOTIS Editing
(01h)
Enable NOTIS Editing
(01h)
*Disable NOTIS Editing
(00h)
*Disable NOTIS Editing
(00h)
50
Barcode scanner configuration guide
MSI
14
MSI
Enable/Disable
MSI
Parameter # 0Bh
Enable/Disable MSI
To enable or disable MSI, scan the appropriate bar code below.
Parameter # 0Bh
To enable or disable MSI, scan the appropriate bar code below.
Enable MSI
(01h)
4 - 62 SE655 Decoded Linear Imaging Engine
4 - 62 SE655 Decoded Linear Imaging Engine
Set Lengths for MSI
Set Lengths for MSI
Parameter # L1 = 1Eh L2 = 1Fh
SetParameter
Lengths for MSI # L1 = 1Eh L2 = 1Fh
*Disable MSI
(00h)
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
Parameter
#
1Eh L2
= 1Fh
The
length
ofL1
a =code
refers
to can
the number
ofany
characters
(i.e.,or
human
readable
characters)
the code
includes
check
digits.
Lengths
for
MSI
be set for
length, one
two discrete
lengths,
or lengths
withincontains,
a specificand
range.
See
check
digits.
Lengths
canequivalents.
beofset
for
any
length,
one
or
discrete
or Setting
lengths
within
a specific
range.
of apage
code
refers
toMSI
the
number
characters
readable
characters)
thelengths,
code contains,
and includes
check
digits. Lengths
for See
MSI
B-5
on
B-9for
for
ASCII
To(i.e.,
sethuman
lengths
viatwo
serial
commands,
see
Code
Lengths
Via
Serial
4Table
-The
62length
SE655
Decoded
Linear
Imaging
Engine
Table
B-5
page
B-9
foror
ASCII
equivalents.
Tolengths
set lengths
via serial
commands, see Setting Code Lengths Via Serial
Commands
page
A-7.
can be
set on
foron
any
length,
one
two discrete
lengths, or
within a specific
range.
Commands on page A-7.
One
Length
- Select
thistooption
decode
only containing
those codes
containing
a example,
selectedselect
length.
select
OneDiscrete
Discrete Length
- Select
this option
decodetoonly
those codes
a selected
length. For
MSI -For
Oneexample,
Discrete Length,
then
OneSet
Discrete
Length
Select
this
option
to
decode
only
those
codes
containing
a
selected
length.
For
example,
select
MSI
One
Discrete
Length,
then
scan
1,
4,
to
decode
only
MSI
symbols
containing
14
characters.
Numeric
bar
codes
for
scan 1, 4,Lengths
to decode only
MSIMSI
symbols containing 14 characters. Numeric bar codes begin on page 56. To change the selection or cancel an incorrect
MSI - One
Discrete
then
1, 4, to
only
MSI symbols
containing
14on
characters.
begin
on page
4-73. Length,
To change
thescan
selection
or decode
cancel an
incorrect
entry, scan
Cancel
page 4-74.Numeric bar codes
entry, scan Cancel on page 57.
begin
on
page
4-73.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page 4-74.
Parameter # L1 = 1Eh L2 = 1Fh
The length of a code refers to the number of characters (i.e., human readable characters) the code contains, and includes
check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths within a specific range. See
Table B-5 on page B-9 for ASCII equivalents. ToMSI
set -lengths
via serial
commands, see Setting Code Lengths Via Serial
One Discrete
Length
Commands on page A-7.
MSI - One Discrete Length
Two Discrete Lengths - Select this option to decode only those codes containing two selected lengths. For example,
One
Length
- -Select
this
option
to
decode
only
codes
containing
atwo
selected
length.
For14
select
Two
Lengths
Select
thisto
option
to
decode
codes
containing
selected
lengths.
For
example,
select
MSI - Two
Discrete
Lengths,
then
scan
0, 6, codes
1,only
4, those
tothose
decode
MSIlengths.
symbols
containing
6 MSI
or
characters.
TwoDiscrete
Discrete
Lengths
- Select
this
option
decode
only
those
containing
twoonly
selected
For example,
select
- example,
Two
Discrete
MSI
One
Discrete
Length,
then
scan
1,
4,
to
decode
only
MSI
symbols
containing
14
characters.
Numeric
bar
codes
select
MSI
Lengths,
then
0, 6,the
1, 4,
to 14
decode
only
MSI
or To
14change
characters.
Numeric
bar- Two
codes
pageonly
4-73.
Toscan
change
selection
or cancel
an symbols
incorrect
entry,
Cancel
on page
Lengths,
then
scan 0,Discrete
6,begin
1, 4, toon
decode
MSI
symbols
containing
6 or
characters.
Numeric
bar codescontaining
begin onscan
page656.
the 4-74.
begin on bar
page
4-73.begin
To change
the4-73.
selection
or cancel
an
incorrect
entry,
scan
Cancel on
page
4-74.
Numeric
codes
on
page
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page
4-74.
selection or cancel an incorrect entry, scan Cancel on page 57.
MSI - One Discrete Length
MSI - Two Discrete Lengths
Two Discrete Lengths - Select this option to decode
onlyDiscrete
those codes
containing two selected lengths. For example,
MSI - Two
Lengths
Length
Within
Range
- Select
thistooption
tocodes
decode
codes
a For
specified
For
example,
toordecode
MSI symbols
select
- Two
Discrete
Lengths,
then scan
0,
6, 1,
4, towithin
decode
only
MSI range.
symbols
containing
14 characters.
LengthMSI
Within
Range
- Select
this
option
decode
within
a specified
range.
example,
to decode
MSI
symbols 6
containing
between
4 and 12
Length
Within
Range
Select
this
option
to
decode
codes
within
a
specified
range.
For
example,
to
decode
MSI
symbols
containing
between
4
and
12
characters,
first
scan
MSI
Length
Within
Range,
then
scan
0,
4,
1
and
2
(single
digit
Numeric
bar
codes
begin
on
page
4-73.
To
change
the
selection
or
cancel
an
incorrect
entry,
scan
Cancel
on
page
4-74.
characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers must always be preceded by a leading zero). Numeric
bar
containingmust
between
4 and
12 characters,
first scan
MSINumeric
Length bar
Within
Range,
then
scan 4-73.
0, 4, 1Toand
2 (single
digit
numbers
always
be
preceded
by
a
leading
zero).
codes
begin
on
page
change
the
selection
or
codes begin on page 56. To change the selection or cancel an incorrect entry, scan Cancel on page 57.
numbers
always
be preceded
by aon
leading
cancel
anmust
incorrect
entry,
scan Cancel
page zero).
4-74. Numeric bar codes begin on page 4-73. To change the selection or
cancel an incorrect entry, scan Cancel on page 4-74.
MSI - Two Discrete Lengths
Length
Within
- Select
thisMSI
option
tosymbols
decode
codes any
within
a specified
range. For example, to decode MSI symbols
Any Length
- ScanRange
this option
to decode
Plessey
number
of characters.
MSIcontaining
- Length
Within
Range
containing between 4 and 12 characters, first scan
MSI
Length
Within
Range,
then scan 0, 4, 1 and 2 (single digit
MSI - Length Within Range
numbers
must
always
beoption
preceded
by a leading
zero). Numeric
codes begin
on page
To change the selection or
Any Length
- Scan
this
to decode
MSI Plessey
symbols bar
containing
any number
of 4-73.
characters.
Barcode
configuration
guide
51
Any
Length
- Scan
this option
to
decode
cancel
anscanner
incorrect
entry,
scan
Cancel
onMSI
pagePlessey
4-74. symbols containing any number of characters.
NOTE
Selecting this option may lead to misdecodes for MSI codes.
MSI Check Digits
NOTE: Selecting this option may lead to misdecodes for MSI codes.
MSI Check#Digits
Parameter
32h
Parameter Menus 4 - 63
Parameter Menus 4 - 63
These
check digits#at32h
the end of the bar code verify the integrity of the data. At least one check digit is always required.
Parameter
MSI
Check
Check
digits
are notDigits
automatically transmitted with the data.
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
MSI
Check
Check
digits
are not
automatically transmitted with the
data.
Parameter
#Digits
32h
MSI
- Any Length
Parameter
These
check digits#at32h
the end of the bar code verify the integrity of the data. At least one check digit is always required.
MSI Check
Check
digitsDigits
are not automatically transmitted with the data.
These check digits at the end of the bar code verify the integrity of the data. At least one check digit is always required.
Parameter
# are
32h not automatically transmitted with the data.
Check
digits
These check digits at the end of the bar code verify the integrity
of the
At least
one check digit is always required. Check digits are not
*One
MSIdata.
Check
Digit
(00h)
automatically transmitted with the data.
*One MSI Check Digit
If two check digits are selected, also select an MSI Check Digit
(00h)Algorithm on page 4-64.
If two check digits are selected, also select an MSI*One
Check
Digit
Algorithm
MSI
Check
Digit on page 4-64.
(00h)
*One MSI Check Digit
If two check digits are selected, also select an MSI Check Digit
(00h)Algorithm on page 4-64.
If two
digits
selected,
alsoanselect
an MSI
Digit Algorithm on page 4-64.
If twocheck
check digits
areare
selected,
also select
MSI Check
Digit Check
Algorithm.
Two MSI Check Digit
(01h)
Two MSI Check Digit
(01h)
Transmit MSI Check Digit
Two MSI Check Digit
(01h)
Two MSI Check Digit
ScanParameter
this symbol to
# transmit
2Eh the check digit with the data. (01h)
Transmit MSI
Check Digit
Parameter
# 2Eh
Transmit
MSI
Check
Transmit
MSI Check
Digit
Digit
Scan this symbol to transmit the check digit with the data.
Parameter
# 2EhMSI Check Digit
Transmit
Parameter
# 2Eh
Scan this symbol to transmit the check digit with the data.
# transmit
2Eh the check digit with the data.
ScanParameter
this symbol to
Scan this symbol to transmit the check digit with the data.
Transmit MSI Check Digit (Enable)
(01h)
Transmit MSI Check Digit (Enable)
Scan this symbol to transmit data without the check digit. (01h)
Scan
symbol
to transmit
data without
the
check digit.
Scan this
this symbol
to transmit
data without
the check
digit.
Transmit
MSI Check Digit (Enable)
(01h)
Transmit MSI Check Digit (Enable)
Scan this symbol to transmit data without the check digit. (01h)
Scan this symbol to transmit data without the check digit.
*Do Not Transmit MSI Check Digit (Disable)
(00h)
*Do Not Transmit MSI Check Digit (Disable)
(00h)
*Do Not Transmit MSI Check Digit (Disable)
(00h)
*Do Not Transmit MSI Check Digit (Disable)
(00h)
52
Barcode scanner configuration guide
Parameter # 33h
When
the Two
check digits option is selected, an additional verification is required to ensure integrity. Select one of the
MSI Check
DigitMSI
Algorithm
following algorithms.
Parameter # 33h
When the Two MSI check digits option is selected, an additional verification is required to ensure integrity. Select one of the following algorithms.
MOD 10/ MOD 11
(00h)
*MOD 10/ MOD 10
(01h)
Barcode scanner configuration guide
53
Enable/Disable GS1 DataBar Omnidirectional
GS1-DataBar
Parameter
# F0h 52h
15
GS1-DataBar
Enable/Disable
GS1 DataBar Omnidirectional
To enable or disable GS1 DataBar Omnidirectional, scan the appropriate bar code below.
Parameter # F0h 52h
Enable/Disable GS1 DataBar Omnidirectional
ToParameter
enable or
disable
# F0h
52h GS1 DataBar Omnidirectional, scan the appropriate bar code below.
To enable or disable GS1 DataBar Omnidirectional, scan the appropriate bar code below.
*Enable GS1 DataBar Omnidirectional
(01h)
*Enable GS1 DataBar Omnidirectional
(01h)
Disable GS1 DataBar Omnidirectional
(00h)
Disable GS1 DataBar Omnidirectional
(00h)
Enable/Disable GS1 DataBar Limited
Parameter # F0h 53h
Enable/Disable
DataBar
Enable/Disable
GS1 DataBarGS1
Limited
Limited
ToParameter
enable or
disable
# F0h
53h GS1 DataBar Limited, scan the appropriate bar code below.
Parameter # F0h 53h
To enable or disable GS1 DataBar Limited, scan the appropriate bar code below.
To enable or disable GS1 DataBar Limited, scan the appropriate bar code below.
*Enable GS1 DataBar Limited
(01h)
*Enable GS1 DataBar Limited
(01h)
Disable GS1 DataBar Limited
(00h)
Disable GS1 DataBar Limited
(00h)
54
Barcode scanner configuration guide
Enable/Disable
Parameter
# F0hGS1
54h DataBar Expanded
Parameter
# F0h
To enable
or disable
GS1 54h
DataBar Expanded, scan the appropriate bar code below.
Enable/Disable GS1 DataBar Expanded
To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below.
Parameter # F0h 54h
To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below.
*Enable GS1 DataBar Expanded
(01h)
*Enable GS1 DataBar Expanded
(01h)
Disable GS1 DataBar Expanded
(00h)
Disable GS1 DataBar Expanded
(00h)
Convert GS1 DataBar to UPC/EAN
Convert
GS1
DataBar
Convert
GS1 DataBar
to UPC/EAN
Parameter
# F0h
8Dh to
UPC/EAN
Parameter
# F0h 8Dh
Parameter
# F0h
8Dh
This
parameter
only
applies
to GS1 DataBar Omnidirectional and GS1 DataBar Limited symbols. When this conversion is
This parameter
only appliesOmnidirectional
to GS1 DataBar Omnidirectional
and GS1 Limited
DataBar Limited
symbols.
When a
thissingle
conversion
enabled,
GS1digit
DataBar
enabled,
GS1 DataBar
and GS1 DataBar
symbols
encoding
zeroisas
the first
have the
This
parameter
only
applies
GS1
DataBar
Omnidirectional
and
DataBar
symbols.
conversion
Omnidirectional
and
GS1
DataBar
symbols
encoding
single zero as
the GS1
first digit
have theLimited
leading ‘010’
strippedWhen
and thethis
bar code
reported is
as
leading
'010' stripped
and
thetoLimited
bar
code
reported
asa EAN-13.
enabled,
EAN-13. GS1 DataBar Omnidirectional and GS1 DataBar Limited symbols encoding a single zero as the first digit have the
Bar
codes
beginning
but not
zeros have the leading '0100' stripped and the bar code reported as
leading
'010'
strippedwith
andtwo
the or
barmore
codezeros
reported
as six
EAN-13.
UPC-A.
The
UPC-A
Preamble
parameter
to
transmit
the
system
and
codereported
appliesasto
converted
bar
Bar codes beginning with two or more zeros but not six zeros have the
leading character
‘0100’ stripped
andcountry
the bar code
UPC-A.
The UPC-A
Bar codes
beginning
withthe
twosystem
or more
zeros butnor
notthe
sixcheck
zeros digit
havecan
thebe
leading
'0100' stripped and the bar code reported as
codes.
Note
that
neither
character
stripped.
Preamble parameter to transmit the system character and country code applies to converted bar codes. Note that neither the system character nor
UPC-A.
The UPC-A Preamble parameter to transmit the system character and country code applies to converted bar
the check
digitthat
can neither
be stripped.
codes.
Note
the system character nor the check digit can be stripped.
Enable Convert GS1 DataBar to UPC/EAN
Enable Convert GS1 DataBar to UPC/EAN
*Disable Convert GS1 DataBar to UPC/EAN
*Disable Convert GS1 DataBar to UPC/EAN
Barcode scanner configuration guide
55
Numeric Bar Codes
16 Numeric Bar Codes
For parameters requiring specific numeric values, scan the appropriately numbered bar code(s).
For parameters requiring specific numeric values, scan the appropriately numbered bar code(s).
0
1
2
3
4
5
56
Barcode scanner configuration guide
Numeric Bar Codes (continued)
6
6
7
7
8
8
9
Cancel
9
Cancel
ToCancel
change
the selection or cancel an incorrect entry, scan the bar code below.
change the
selection
or cancel
an incorrect
entry, scanentry,
the barscan
code below.
ToTochange
the
selection
or cancel
an incorrect
the bar code below.
Cancel
Cancel
Barcode scanner configuration guide
57
Specifications are subject to change without notice.
© 2013 Speech Processing Solutions GmbH. All rights reserved. Philips and the Philips’ shield
emblem are registered trademarks of Koninklijke Philips Electronics N.V. and are used by
Speech Processing Solutions GmbH under license from Koninklijke Philips Electronics N.V.
All trademarks are the property of their respective owners.
Document version 1.0, 2013/04/10.