1. General Instructions Function Instructions: Rear View:

advertisement
1. General Instructions
— A profession remote controller with 4Ch. /8Ch. Switchable
— Can connect witch LED-CC or LED-PC300/100 to control passive LED fixtures
— 9 different hold-color buttons for instant colors
— 12 different color chases triggered by music
— 32 different mix colors, including color fade
— Speed and dimmer adjustable by fader
— Full on and blackout functions
— Used together with CA-32F foot dimmer.
— Power supply: DC 9V 300 mA
— Dimension: 180X 130 X 50 mm
— Weight: 1 kg
Function Instructions:
Mode select
Fixed color
/ chase
Use to select Fixed Color / Chase 1 / Chase 2 / Spectrum mix mode
1. In Fixed Color mode, use to select color on Red /Orange / Yellow / Green / cyan
/ Blue / Purple / Magenta /White
2. In Chase 2 mode (the LED blinking), use to select 8 chase or random chase.
Chase 1 fader
In Chase 1 (the LED on) mode, use the fader to select color chases on Standard
chase / Bright chase / Mood chase / spectrum random chase / Spectrum sequence
chase / Dynamic chase / Red-Green+ Blue / Green-Red + Blue / Blue-Red /
Yellow-Blue / Red-Green / Yellow-Green
Spectrum Mix
fader
Use to select 32 spectrum mix colors in Spectrum mix mode.
Speed fader
Use to adjust chase speed in the range of 0.1 to 2.5 seconds
Fade Time
fader
Master fader
Black out
Full on
Sound to
chase
Use to adjust fade time. Fade time is amount of one color to fade in or fade out
Use to dimmer / shutter the fixture
Blackout the fixture
All lighting effect at once
Use to receive audio signal for sound activated
Rear View:
Power Switch
Turn On/Off the power
Channel Mode Switch
Translate between 4 addresses mode and 8 addresses mode
DC Input
DC 9V 300mA min
DMX Output
Output DMX signal to the connected fixture
DMX Input
Input DMX signal to the connected fixture
2. Address setting
Each time you make a different connection, you have to reset the address. There are two ways that
you can set address for the LED lightings:
Manual address setting:
a. Set LED-RC8F to 4 Ch. (the address should be 1, 2, 3 or 4) or 8 Ch.
Button
address
Chase 1
1
b. Connecting all LED lightings to the LED-RC8F and power them on.
Chase 2
2
c. Hold the “black out” button for about 5 seconds until the red indicator
Chase 3
3
Chase 4
4
d. The first LED lighting will be on.
Chase 5
5
e. Set address for the first lighting by pressing the chase 1-8 buttons.
Chase 6
6
Chase 7
7
Chase 8
8
(the address should be 1, 2, 3, 4, 5, 6, 7, or 8) mode.
LED blinking.
f. Press the “sound to chase” or “full on” button to select other fixtures,
and addressing for them.
g. Press the “black out” button for about 5 seconds to exit address setting.
Automatic address setting:
a. Set LED-RC8F to 4 Ch. (the address should be 1, 2, 3 or 4) or 8 Ch. (the address should be 1, 2,
3, 4, 5, 6, 7, or 8) mode.
b. Connecting all LED lightings to the LED-RC8F and power them on.
c. Hold the “black out” button for about 5 seconds until the red indicator LED blinking.
d. The first LED lighting will be on.
e. Press the “sound to chase” or “full on” button until all LED lightings on.
f. Press “random” button to set address automatically.
g. Press the “black out” button for about 5 seconds to exit address setting.
h. The address of lightings in the chain will be 1234-1234-… (12345678-12345678-…)
3. How to Connect the unit
Please refer to the following diagram to connect the fixtures:
A. Connect with COLOR BALL/COLOR SPOT/CA-32F
B. Connect with COLOR PAR/ CA-32F
Attention: Before address setting, be sure DIP switches 0 to 9 of all lightings are in “OFF” position.
Download