कायग योजना
(1 जु ीाई २०१४
ववधुत तकनीकी ववभार्
तक)
PROGRAMME OF WORK
(AS ON 1 JULY, 2014)
(ईटवडी)
ELECTROTECHNICAL
DEPARTMENT
(ETD)
भारतीय मानक बयू रो,
मानक भवन, 9, बहादरु शाह जफर मार्ग
नई ददल्ीव –110 002
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN, 9, BAHADUR SHAH ZAFAR MARG, NEW DELHI – 110 002
PREFACE
The program of work is prepared by all divisions of Bureau of Indian Standards to
indicate the latest position of published standards and draft standards at different stages
of processing. This has been prepared Sectional Committee-wise as on 1 July, 2014 and
arranged in the sequential order of the committee number.
This document covers the programme of work of Electrotechnical Division Council
(ETDC) with its scope as under:
“Standardization in the field of electrical power generation, transmission, distribution and
utilization equipment, and insulating materials, winding wires, measuring and process
control instruments and primary and secondary batteries”.
For the convenience of the users, the content page includes the list of Sectional
Committees together with the corresponding Technical Committees of IEC/ISO. It may
be mentioned that the work under Electrotechnical Division Council closely follows the
international standardization work under the International Electrotechnical Commission
(IEC).
This document covers designation of the Sectional Committee, its scope, number and title
of the published/draft standards, date of reaffirmation, No. of amendments issued, etc.
An ‘*’ before IS No. has been used to indicate that the standards is under revision.
Wherever, below IS number, ‘ISO/IEC number is given, it indicates the ISC/IEC
Standards has been adopted under dual numbering system.
In addition to general series of Indian Standards designated by ‘IS’, this document also
covers special series of publications designated by ‘SP’.
This publication also contains the following Annexes:
a) Annex 1- List of standards withdrawn/superseded
b) Annex 2- List of Equivalent Standards
c) Annex 3- Bilingual Standards
d) Annex 4- Aspect wise Classification of Standards
We have tried our level best to provide this information. Any suggestions for
improvement are always welcomed.
For any information, please write to:
SCIENTIST ‘F’ and HEAD
ELECTROTECHNICAL DEPARTMENT (ETD)
BUREAU OF INDIAN STANDARDS
MANAK BHAWAN, 9 B.S. ZAFAR MARG
NEW DELHI-110002
Email – eetd@bis.org.in, Phone – 011 23231192
CONTENTS
Committee
No.
ETD 01
ETD 02
ETD 03
ETD 06
ETD 07
ETD 08
ETD 09
ETD 10
ETD 11
ETD 12
ETD 13
ETD 14
ETD 15
ETD 16
ETD 18
ETD 19
ETD 20
ETD 21
ETD 22
ETD 23
ETD 24
ETD 25
ETD 28
ETD 29
ETD 30
ETD 31
ETD 32
ETD 33
ETD 34
ETD 35
ETD 36
Committee Name
BASIC ELECTROTECHNICAL STANDARDS
SOLID ELECTRICAL INSULATING MATERIALS
AND INSULATING SYSTEMS
FLUIDS FOR ELECTROTECHNICAL
APPLICATIONS
ELECTRICAL INSULATORS AND ACCESSORIES
LOW VOLTAGE SWITCHGEAR &
CONTROLGEAR
HIGH VOLTAGE SWITCHGEAR AND
CONTROLGEAR
POWER CABLES
PRIMARY CELLS AND BATTERIES
SECONDARY CELLS AND BATTERIES
MEASURING EQUIPMENT FOR BASIC
ELECTRICAL QUANTITIES
EQUIPMENT FOR ELECTRICAL ENERGY
MEASUREMENT AND LOAD CONTROL
ELECTRICAL WIRING ACCESSORIES
ROTATING MACHINERY
TRANSFORMERS
INDUSTRIAL PROCESS MEASUREMENT AND
CONTROL
HIGH VOLTAGE ENGINEERING
ELECTRICAL INSTALLATIONS
ELECTRIC WELDING EQUIPMENT
ELECTRICAL APPARATUS FOR EXPLOSIVE
ATMOSPHERES
ELECTRIC LAMPS AND THEIR AUXILIARIES
ILLUMINATION ENGINEERING AND
LUMINAIRES
LIFTS AND ESCALLATORS
SOLAR PHOTOVOLTAIC ENERGY SYSTEMS
POWER CAPACITORS
SURGE ARRESTERS
POWER ELECTRONICS
ELECTRICAL APPLIANCES
WINDING WIRES
INSTRUMENT TRANSFORMERS
POWER SYSTEMS RELAYS
TOOLS AND EQUIPMENT FOR LIVE WORKING
Page
1
5
14
17
20
23
25
31
32
35
38
40
43
49
52
57
59
63
65
69
73
76
78
81
84
85
87
93
98
100
104
ETD 37
ETD 45
CONDUCTORS AND ACCESSORIES FOR
OVERHEAD LINES
FUSES
HVDC POWER SYSTEMS
WIND TURBINES
STANDARDIZATION OF ENVIRONMENTAL
ASPECTS FOR ELECTRICAL & ELECTRONIC
PRODUCTS
SAFETY OF MACHINERY- ELECTROTECHNICAL
ASPECTS
POWER QUALITY
ETD 46
GRID INTEGRATION
ETD 39
ETD 40
ETD 42
ETD 43
ETD 44
ANNEX 1 LIST OF STANDARDS WITHDRAWN/SUPERSEDED
ANNEX 2 LIST OF EQUIVALENT STANDARDS
ANNEX 3 BILINGUAL STANDARDS
ANNEX 4 ASPECT WISE CLASSIFICATION OF STANDARDS
105
107
109
110
111
Newly
Started
Newly
Started
Newly
Started
ETD 1 BASIC ELECTROTECHNICAL STANDARDS
SCOPE - To prepare standards of general and common nature in the field of
electrotechnology, such as voltages, current ratings and frequency,
quantities and units, nomenclature,graphical symbols, basic marking and
general requirements for enclosures of equipment.
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1885(Part 1):1961
Electrotechnical vocabulary: Part 1 Fundamental
definitions
Jul 2012
2
IS 1885(Part 9):1992
/ IEC 60050(446):1983
Electrotechnical Vocabulary: Part 9 Electrical relays
(second revision)
Jul 2012
3
IS 1885(Part 10):2008
/ IEC 60050(448):1995
Electrotechnical Vocabulary: Part 10 Power system
protection (second revision)
Dec 2013
4
IS 1885(Part 11):1966
Electrotechnical vocabulary: Part 11 Electrical
measurements
Jul 2012
5
IS 1885(Part 14):1967
Electrotechnical vocabulary:Part 14 Nuclear power
plants
Jul 2012
6
IS 1885(Part 15):2008
/ IEC 60050(482):2004
Electrotechnical vocabulary: Part 15 Primary and
secondary cells and batteries (second revision)
[Amalgamating IS 1885(Part 8):1986]
Aug 2013
7
IS 1885(Part 16/Sec 1):1968
Electrotechnical vocabulary: Part 16 Lighting, Section
1 General aspects
Jul 2012
8
IS 1885(Part 16/Sec 2):1968
Electrotechnical vocabulary: Part 16 Lighting, Section
2 General illumination, lighting fittings and lighting for
traffic and signalling
Jul 2012
9
IS 1885(Part 16/Sec 3):1967
Electrotechnical vocabulary: Part 16 Lighting, Section
3 Lamps and auxiliary apparatus
Jul 2012
10
IS 1885(Part 17):1979
Electrotechnical vocabulary: Part 17 Switchgear and
controlgear (first revision)
Jul 2012
11
IS 1885(Part 27):2008
/ IEC 60050(551):1998
Electrotechnical Vocabulary: Part 27 Power electronics
(Third Revision)
Aug 2013
12
IS 1885(Part 28):1993
/ IEC 60050(321):1986
Electrotechnical vocabulary: Part 28 Instrument
transformers (first revision)
Mar 2014
13
IS 1885(Part 29):1971
Electrotechnical vocabulary: Part 29 Mining terms
Jul 2012
14
IS 1885(Part 30):1971
Electrotechnical vocabulary: Part 30 Overhead
transmission and distribution of electrical energy
Jul 2012
15
IS 1885(Part 32):1993
/ IEC 60050(461):1984
Electrotechnical Vocabulary: Part 32 Electric cables
(first revision)
Mar 2014
16
IS 1885(Part 34):1972
Electrotechnical vocabulary: Part 34 Cinematography
Jul 2012
17
IS 1885(Part 35):1993
/ IEC 60050(411):1996
Electrotechnical vocabulary: Part 35 Rotating
machinery (first revision)
Mar 2014
18
IS 1885(Part 37):1993
/ IEC 60050(691):1973
Electrotechnical vocabulary: Part 37 Tariffs for
electricity (first revision)
Mar 2014
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
1
2
19
IS 1885(Part 38):1993
/ IEC 60050(421):1990
Electrotechnical vocabulary: Part 38 Power
transformers and reactors
(second revision)
Mar 2014
20
IS 1885(Part 42):1993
/ IEC 60050(436) :1990
Electrotechnical Vocabulary: Part 42 Power capacitors
(second revision)
Mar 2014
21
IS 1885(Part 43):1977
Electrotechnical vocabulary: Part 43 Electrical
equipment used in medical practice
Jul 2012
22
IS 1885(Part 49):1978
Electrotechnical vocabulary: Part 49 Industrial process
measurement and control
Jul 2012
23
IS 1885(Part 51):2012
/ IEC 60050-841:2004
Electrotechnical vocabulary: Part 51 Industrial electroheating (Second Revision)
24
IS 1885(Part 53):1980
Electrotechnical vocabulary: Part 53 Mica (superseding
IS:1174)
25
IS 1885(Part 54):1993
/ IEC 60050(471):1984
26
IS 1885(Part 55):1981
27
IS 1885(Part 57):2008
/ IEC 60050(131):2002
Electrotechnical vocabulary: Part 57 Circuit Theory
(Second Rrevision)
Aug 2013
28
IS 1885(Part 60):1993
/ IEC 60050(426):1990
Electrotechnical Vocabulary: Part 60 Electrical
apparatus for explosive atmospheres (first revision)
Mar 2014
29
IS 1885(Part 61):1985
Electrotechnical vocabulary: Part 61 Nuclear medical
instruments
Jul 2012
30
IS 1885(Part 62):1993
/ IEC 60050(212):1990
Electrotechnical vocabulary: Part 62 Solid insulating
materials (first revision)
Mar 2014
31
IS 1885(Part 69):1993
/ IEC 60050(602):1983
Electrotechnical Vocabulary: Part 69 Generation,
transmission and distribution of electricity - Generation
Mar 2014
32
IS 1885(Part 70):1993
/ IEC 60050(604):1987
Electrotechnical Vocabulary: Part 70 Generation,
transmission and distribution of electricity - operation
Mar 2014
33
IS 1885(Part 71):1993
/ IEC 60050(605):1983
Electrotechnical Vocabulary: Part 71 Generation,
transmission and distribution of electricity - Substations
Mar 2014
34
IS 1885(Part 72):2008
/ IEC 60050 (101):1998
Electrotechnical Vocabulary : Part 72 Mathematics
(First Revision)
May 2013
35
IS 1885(Part 73):2012
/ IEC 60050-111:1996
Electrotechnical Vocabulary : Part 73 Physics and
Chemistry [First Revision]
36
IS 1885(Part 74):2012
/ IEC 60050(151): 2001
Electroechnical Vocabulary: Part 74 Electrical and
magnetic devices(First Revision)
37
IS 1885(Part 75):2012
/ IEC 60050-351 2006
Electrotechnical Vocabulary: Part 75 Automatic control
(First Revision)
38
IS 1885(Part 76):1993
/ IEC 60050(431):1980
Electrotechnical vocabulary: Part 76 Transducers
Mar 2014
39
IS 1885(Part 77):1993
/ IEC 60050(466): 1990
Electrotechnical Vocabulary: Part 77 Overhead lines
Mar 2014
40
IS 1885(Part 78):1993
/ IEC 60050(601):1985
Electrotechnical Vocabulary: Part 78 Genereation,
transmission and distribution of electricity - General
Mar 2014
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
Electrotechnical Vocabulary: Part 54 Insulators (First
revision)
Electrotechnical vocabulary: Part 55 Electric fans
2
Jul 2012
Mar 2014
Jul 2012
41
IS 1885(Part 79):1993
/ IEC 60050(603):1986
Electrotechnical Vocabulary: Part 79 Generation,
transmission and distribution of electiricity - Power
system planning and management
Mar 2014
42
IS 1885(Part 80):1994
/ IEC 60050(301):1983
Electrotechnical vocabulary: Part 80 General terms on
measurements in electricity
Mar 2014
43
IS 1885(Part 81):1993
/ IEC 60050(302):1983
Electrotechnical vocabulary: Part 81 Electrical
measuring instruments
Mar 2014
44
IS 2032(Part 15):1976
Graphical symbols used in electrotechnology:
Part 15 Aircraft electrical symbols
Jul 2012
45
IS 2032(Part 19):1977
Graphical symbols used in electrotechnology:
Part 19 Electrical equipment used in medical practice
Jul 2012
46
IS 2032(Part 25):1980
Graphical symbols used in electrotechnology:
Part 25 Electrical installations in ships
Mar 2014
47
IS 3599:1966
Methods of measurement of cooling medium
temperature for electrical apparatus
Mar 2014
48
IS 3722(Part 1):1983
| IEC 60027-1(1992)
Letter symbols and signs used in electrical technology:
Part 1 General guidance on symbols and subscripts
(first revision)
Jul 2012
49
IS 3722(Part 2):1983
| IEC 60027-1(92)
Letter symbols and signs used in electrical technology:
Part 2 Reference tables for symbols and subscripts
(first revision)
Jul 2012
50
IS 5578:1984
| IEC 60391(1972)
Guide for marking of insulated conductors (first
revision)
Mar 2011
Recommendations for direction of movement for
control devices operating electrical apparatus
Mar 2013
51
IS 7118:1973
52
* IS 7691:1975
| IEC 60113-1(71)
Frequencies for special power applications
Mar 2014
53
IS 8270(Part 1):1976
| IEC 60113-1(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 1 Definitions and
classification
Mar 2014
54
IS 8270(Part 2):1976
| IEC 60113-2(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 2 Item designation
Mar 2014
55
IS 8270(Part 3):1977
| IEC 60113-2(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 3 General requirements for
diagrams
Mar 2009
56
IS 8270(Part 4):1977
| IEC 60113-2(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 4 Circuit diagrams
Mar 2009
57
IS 8270(Part 5):1976
| IEC 60113-2(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 5 Interconnection diagrams
and tables
Mar 2014
58
IS 8270(Part 6):1983
| IEC 60113-2(71)
Guide for preparation of diagrams, charts and tables
for electrotechnology: Part 6 Unit wiring diagrams and
tables
Jul 2012
59
IS 9409:1980
| IEC 61140 (2001)
Classification of electrical and electronic equipment
with regard to protection against electric shock
Jul 2012
60
IS 9499:1980
| IEC 60375(72)2003
Conventions concerning electric and magnetic circuits
Mar 2014
Reference ambient temperature for electrical
equipment
Mar 2009
61
IS 9676:1980
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
3
1
62
IS 9677:1980
Guide for limits of temperature-rise of the windings of
electrical equipment when tested by different methods
Mar 2014
63
IS 9678:1980
Methods of measuring temperature rise of electrical
equipment
Mar 2014
64
IS 10381:1982
Terms (and their Hindi equivalents) commonly used for
name plates and similar data of electrical power
equipment
Mar 2009
65
IS 10580:1983
Service conditions for electrical equipment
Jul 2012
66
IS 11353:1985
| IEC 60445(1973)
Guide for uniform system of marking and identification
of conductors and apparatus terminals
Jul 2012
67
IS 11354:1985
| IEC 60152(63)
Guide for identification by hour numbers of the phase
conductors of 3-phase electric systems
Jul 2012
68
IS 11954:1987
Guide for colour coding of electrical mimic diagrams
Mar 2014
69
IS 11955:1987
| IEC 60059(1999)
Preferred current ratings
Mar 2014
70
IS 12032(Part 1):1987
/ IEC 60617-1(1985)
Graphical symbols for diagrams in the field of
electrotechnology: Part 1 General information,general
index,cross reference table
Mar 2014
71
IS 12032(Part 2):1987
/ IEC 60617-2(1983)
Graphical symbols for diagrams in the field of
electrotechnology: Part 2 Symbols elements,
qualifying symbols and other symbols having general
application
Mar 2014
72
IS 12032(Part 3):1987
/ IEC 60617-3(1983)
Graphical symbols for diagrams in the field of
electrotechnology:Part 3 Conductors and connecting
devices
Mar 2014
73
IS 12032(Part 4):1987
/ IEC 60617-4(1984)
Graphical symbols for diagrams in the field of
electrotechnology: Part 4 Passive components
Mar 2014
74
IS 12032(Part 6):1987
/ IEC 60617-6(1983)
Graphical symbols for diagrams in the field of
electrotechnology: Part 6 Production and conversion of
electrical energy
Mar 2014
75
IS 12032(Part 7):1987
/ IEC 60617-7(1983)
Graphical symbols for diagrams in the field of
electrotechnology: Part 7 Switchgear, controlgear and
protective devices
Mar 2014
76
IS 12032(Part 8):1987
/ IEC 60617-8(1983)
Graphical symbols for diagrams in the field of
electrotechnology: Part 8 Measuring instruments,
lamps
and signalling devices
Mar 2014
77
IS 12032(Part 11):1987
/ IEC 60617-11(1983)
Graphical symbols for diagrams in the field of
electrotechnology: Part 11 Architectural and
topographical installation plans and diagrams
Mar 2014
78
IS 12360:1988
| IEC 60038(1983)
Voltage bands for electrical installations including
preferred voltages and frequency (superseding IS:585)
Dec 2010
79
IS 60529:2001
/ IS/IEC 60529:2001
Classification of Degrees of protection provided by
enclosures (IP Code) (Superceding IS 12063:1987)
Jun 2009
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
4
4
ETD 2 SOLID ELECTRICAL INSULATING MATERIALS AND INSULATION
SYSTEMS
SCOPE - To prepare standards:
a) on solid electrical insulating materials.
b) on guiding principles and on the philosophy of evaluation of insulation
systems in general
c) for functional test programmes and methods intended for evaluation of
possible insulation systems and their suitability for use in electrical
equipment.
d) for classification of insulation systems based upon their capability to
withstand the complex of the most important service determined by the
conditions of the use of insulation in equipment.
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1175:1981
| ISO 67
Methods for grading and classification of muscovite
mica blocks, thins and films (first revision)
2
IS 1271:2012
/ IEC 60085 (2007)
Electrical Insulation - Thermal Evaluation and
designation (Second Revision)
3
4
IS 1576:1992
IS 2259:1963
| IEC 60167(1964)
Oct 2011
Solid pressboard for electrical purposes(first revision)
Apr 2013
1
Methods of test for determination of insulation
resistance of solid insulating materials
Oct 2010
1
5
IS 2260:1973
Preconditioning, conditioning and testing of solid
electrical insulating materials (first revision)
Apr 2013
6
IS 2448(Part 1):1963
Adhesive insulating tapes for electrical purposes:
Part 1 Tapes with cotton textile substrates
Oct 2010
5
7
IS 2464:1963
Built-up mica for electrical purposes
Apr 2013
1
8
IS 2584:1963
Method of test for electric strength of solid insulating
materials at power frequencies
Oct 2011
1
Method for the determination of the proof and the
comparative tracking indices of solid insulating
materials (second revision)
Nov 2012
9
IS 2824:2007
/ IEC 60112:2003
10
IS 3352:1965
Varnished cotton cloth and tape for electrical purposes
Oct 2011
11
IS 3396:1979
Methods of test for volume and surface resistivities of
solid electrical insulating materials (first revision)
Oct 2011
12
IS 4248:1967
Non-ignitable and self-extinguishing boards (with
mineral base) for electrical purposes
Apr 2013
13
IS 4249:1967
Classification and methods of tests for non-ignitable
and self-extinguishing properties of solid electrical
insulating materials
Apr 2013
14
IS 4486:1967
Recommended methods for the determination of the
permittivity and dielectric dissipation factor of
electrical insulating materials at power, audio and radio
frequencies including metre wavelengths
Apr 2013
15
IS 4819:1968
Thin vulcanized fibre sheet (including leatheroid) for
electrical purposes - Specification
Oct 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
5
1
1
16
IS 4820:1968
Vulcanized fibre sheets for electrical purposes Specification
Oct 2011
17
IS 5596:1970
Method of test for determining deleterious substances
in fibrous insulating materials
Oct 2010
18
IS 5711:1970
Vulcanized fibre rods and tubes for electrical purposes
Apr 2013
19
IS 6230:1970
Woven asbestos tape for electrical insulating purposes
Apr 2013
20
IS 6659:1976
Electronic grade ceramic materials (first revision)
Oct 2011
21
IS 7084:1973
Bitumen based filling compounds for electrical
purposes
Mar 2013
22
IS 7571:1974
Methods of tests for ceramic for telecommunication
and allied purposes
Oct 2010
23
IS 7755:1975
High tension insulating cotton tape
impregnated with bitumen based compound
Apr 2013
1
24
IS 7809(Part 1):1975
| IEC 60454-1(1974)
Pressure sensitive adhesive tapes for electrical
purposes: Part 1 General requirements
Apr 2013
2
25
IS 7809(Part 2):1977
| IEC 60454-2(1974)
Pressure sensitive adhesive tapes for electrical
purposes: Part 2 Methods of test
Oct 2011
1
26
IS 7809(Part 3/Sec 1):1986
| IEC 60454-2
Pressure sensitive adhesive tapes for electrical
purposes: Part 3 Requirements for individual materials,
Section 1 Plasticized polyvinylchloride tapes with nonthermosetting adhesive (first revision)
Oct 2011
1
27
IS 7809(Part 3/Sec 2):1981
Pressure sensitive adhesive tapes for electrical
purposes: Part 3 Specifications for individual
materials, Section 2 Requirements for polyester film
tapes (PETP) with thermosetting adhesive
Oct 2011
28
IS 7809(Part 3/Sec 3):1981
Pressure sensitive adhesive tapes for electrical
purposes: Part 3 Specifications for individual materials,
Section 3 Polyester film tapes (PETP) with nonthermosetting adhesive
Oct 2011
29
IS 7809(Part 3/Sec 4):1977
Pressure sensitive adhesive tapes for electrical
purposes: Part 3 Specifications for individual materials,
Section 4 Cellulosic paper, creped with thermosetting
adhesive
Apr 2013
30
IS 7809(Part 3/Sec 5):1977
Pressure sensitive adhesive tapes for electrical
purposes: Part 3 Specifications for individual
materials, Section 5 Cellulosic paper with
thermosetting adhesive
Oct 2011
31
IS 8504(Part 1):2012
Electrical insulating materials properties of thermal
endurance Part 1: Ageing procedures and evaluation
of test results (Second Revision)
32
IS 8504(Part 2):2013
| IEC 60216-2(2005)
Electrical insulating materials - Thermal endurance
properties - Part 2: Determination of thermal
endurance properties of electrical insulating materials Choice of test criteria (First Revision)
33
IS 8504(Part 3):1994
| IEC 60216-3
Guide for determination of thermal endurance
properties of electrical insulating materials Part 3 :
Statistical methods
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
6
Feb 2014
34
IS 8504(Part 4):2013
| IEC 60216-3(2006)
Electrical insulating materials - Thermal endurance
properties - Part 4: Instructions for calculating thermal
endurance characteristics (First Revision)
35
IS 8504(Part 5/Sec 1):2012
| IEC 60216-4-1(2006)
Electrical insulating materials - Thermal endurance
properties - Part 5 Ageing ovens Sec 1 Singlechamber ovens
36
IS 8504(Part 5/Sec 2):2012
| IEC 60216-4-2(2000)
Electrical insulating materials - Thermal endurance
properties - Part 5: Ageing ovens Sec 2 Precision
ovens for use up to 300 °C
37
IS 8504(Part 5/Sec 3):2012
| IEC 60216-4-3(2000)
Electrical insulating materials - Thermal endurance
properties - Part 5 Ageing ovens Sec 3 Multi-chamber
ovens
38
IS 8504(Part 6):2012
| IEC 60216-5(2008)
Electrical insulating materials - Thermal endurance
properties - Part 6: Determination of relative thermal
endurance index (RTE) of an insulating material
39
IS 8504(Part 7):2012
| IEC 60216-6(2006)
Electrical insulating materials - Thermal endurance
properties - Part 7 : Determination of thermal
endurance indices (TI and RTE) of an insulating
material using the fixed time frame method
40
IS 8516:2011
/ IEC 60426(2007)
Electrical Insulating materials – Determination of
electrolytic corrosion caused by insulating materials –
Test methods (First Revision)
41
IS 8570:1977
Press paper for electrical purposes
Oct 2011
42
IS 9043:1979
| ISO 444(1965)
Method for grading (by size) of phlogopite mica blocks,
thins and splittings
Oct 2011
43
IS 9044:1979
| ISO 5972(1978)
Method of measuring thickness of mica blocks, thins,
films and splittings
Oct 2011
44
IS 9045:1979
| ISO 5023(1977)
Thermal classification of phlogopite mica splittings
Oct 2011
45
IS 9335(Part 1):1979
| IEC 60554-1(1977)
Cellulosic papers for electrical purposes: Part 1
Definitions and general requirements
Oct 2011
46
IS 9335(Part 2):1998
/ IEC 60554-2(2001)
Cellulosic papers for electrical purposes: Part 2
Methods of test (superseding IS:2188)
Oct 2011
47
IS 9335(Part 3/Sec 1):1984
| IEC 60554-3-1
Cellulosic papers for electrical purposes: Part 3
Specifications for individual materials, Section 1
General purposes electrical paper
Oct 2011
48
IS 9335(Part 3/Sec 2):1985
| IEC 60554-3-2
Cellulosic papers for electrical purposes: Part 3
Specifications for individual materials, Section 2
Capacitor paper
Oct 2011
49
IS 9335(Part 3/Sec 3):1984
| IEC 60554-3-3(1980)
Cellulosic papers for electrical purposes: Part 3
Specifications for individual materials, Section 3 Crepe
paper
Oct 2011
50
IS 9335(Part 3/Sec 4):1984
| IEC 60554-3-4(1979)
Cellulosic papers for electrical purposes: Part 3
Specifications for individual materials, Section 4
Electrolytic capacitor paper
Oct 2011
51
IS 9335(Part 3/Sec 5):1985
| IEC 60554-3-5
Cellulosic papers for electrical purposes: Part 3
Specifications for individual materials, Section 5
Special papers
Oct 2011
1
Classification of muscovite mica blocks, thins and films
based on electrical properties
Oct 2011
1
52
IS 9455:1980
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
7
1
1
53
IS 9502:1980
| ISO 5816-1(1979)
Muscovite mica components for electronic equipment
54
IS 9947:2011
/ IEC 60587(2007)
Electrical Insulating materials used under severe
ambient conditions – Test methods for evaluating
resistance to tracking and erosion (First Revision)
55
* IS 10026(Part 1):1998
| IEC 60464-1(1976)
Insulating varnishes containing solvents: Part 1
Definitions and general requirements (first revision)
May 2013
56
* IS 10026(Part 2):1999
| IEC 60464-2(19860
Insulating varnishes containing solvents: Part 2
Methods of tests(first revision)
Aug 2009
57
* IS 10026(Part 3/Sec 1):1999
| IEC 60464-3-1(1986)
Insulating varnishes containing solvents: Part 3
Specifications for individual materials,
Section1Requirements for cold curing varnishes
(first revision)
Feb 2014
58
* IS 10026(Part 3/Sec 2):1999
| IEC 60464-3-2(1989)
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 2
Requirements for hot curing varnishes
(first revision)
Jan 2014
59
IS 10026(Part 3/Sec 3):1983
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 3 Air
drying varnishes with temperature index 130
Oct 2011
1
60
IS 10026(Part 3/Sec 4):1983
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 4
Baking varnishes with temperature index 120
Oct 2011
1
61
IS 10026(Part 3/Sec 5):1983
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 5
Baking varnishes with temperature index 130
Oct 2011
1
62
IS 10026(Part 3/Sec 6):1983
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 6
Baking varnishes with temperature index 155
Oct 2011
1
63
IS 10026(Part 3/Sec 7):1983
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 7
Baking varnishes with temperature index 180
Oct 2011
1
64
IS 10026(Part 3/Sec 8):1986
Insulating varnishes containing solvents:
Part 3 Specifications for individual materials,
Section 8 Baking varnishes with temperature index 200
Apr 2013
65
IS 10026(Part 3/Sec 9):1986
Insulating varnishes containing solvents: Part 3
Specifications for individual materials, Section 9
Baking varnishes with temperature index 130 for
magnetic core sheets
Apr 2013
Recommended methods of tests for the determination
of dielectric properties of insulating materials at
frequencies above 300 MHz: Part 1 General
Apr 2013
66
IS 10163(Part 1):1982
| IEC 60377-1(1973)
Oct 2011
67
IS 10192:1982
Synthetic resin bonded glass fibre (SRBGF) sheets for
electrical purposes
Oct 2010
68
IS 10333:1982
Epoxy resin systems for cast resin insulated power
and control cable joints and terminations upto and
including 11 kV
Apr 2013
69
IS 10581:1983
| IEC 60589(1977)
Methods of test for determination of ionic impurities in
electrical insulating materials by extraction with liquids
Oct 2010
70
IS 11182(Part 1):1984
| IEC 60505(1975)
Guide for evaluation of insulation systems of electrical
equipment: Part 1 Identification, evaluation and ageing
mechanisms
Oct 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
8
1
71
IS 11182(Part 2):1984
| IEC 60611(1978)
Guide for evaluation of insulation systems of electrical
equipment: Part 2 Thermal endurance test procedure
Oct 2011
72
IS 11182(Part 3/Sec 1):1986
| IEC 60727-1(1982)
Guide for evaluation of insulation systems of electrical
equipment: Part 3 Electrical endurance test
procedures, Section 1 General considerations and
evaluation procedures based on normal distributions
Oct 2011
73
IS 11182(Part 3/Sec 2):1996
| IEC 60727-2(1993)
Guide for evaluation of insulation systems of electrical
equipments: Part 3 Electrical endurance test
procedures Section 2 evaluation procedure based on
extreme value distribution
Oct 2011
74
IS 11182(Part 5):1993
/ IEC 60941(1988)
Guide for evaluation of insulation system of electrical
equipment: Part 5 Mechanical endurance functional
tests
Dec 2013
75
IS 11182(Part 6):1986
Guide for evaluation of insulation systems of electrical
equipment: Part 6 Performance evaluation based on
service experience and functional tests
Oct 2011
76
IS 11182(Part 7/Sec 1):1986
Guide for evaluation of insulation systems of electrical
equipment: Part 7 Multifactor functional testing,
Section 1 Test procedures
Oct 2011
77
IS 11221:1984
| IEC 60343(1970)
Recommended test methods for determining the
relative resistance of insulating materials to breakdown
by surface discharges
Oct 2011
78
IS 11256(Part 1):1985
| IEC 60370(1971)
Method of test for determination of thermal endurance
of insulating varnishes: Part 1 Electric strength method
Oct 2011
79
IS 11256(Part 2):1985
Method of test for determination of thermal endurance
of insulating varnishes: Part 2 Measurement of loss of
mass
Oct 2011
80
IS 11256(Part 3):1985
| IEC 60290(1969)
Methods of test for determination of thermal
endurance of insulating varnishes: Part 3 Bond
strength by helical coil method
Oct 2011
81
IS 11297(Part 1):1985
Varnished fabrics for electrical purposes: Part 1
Definitions and general requirements
Oct 2011
82
IS 11297(Part 2):1988
Varnished fabrics for electrical purposes: Part 2
Methods of tests
Oct 2010
83
IS 11297(Part 3/Sec 1):1988
Varnished fabrics for electrical purposes: Part 3
Specifications for individual materials, Section 1 Glass
fabric backed varnished fabrics
Oct 2010
84
IS 11298(Part 1):1985
| IEC 60674-1(1980)
Plastic films for electrical purposes: Part 1 Definitions
and general requirements
Oct 2011
85
IS 11298(Part 2):1999
/ IEC 60674-2(1988)
Plastic films for electrical purposes: Part 2 Methods of
test (first revision)
Jan 2014
86
IS 11298(Part 3/Sec 1):1991
Plastic films for electrical purposes: Part 3
Specifications for individual materials, Section 1
Polypropylene film for capacitors (first revision)
Oct 2010
87
IS 11298(Part 3/Sec 2):1999
Plastic films for electrical purposes: Part 3
Specifications for individual materials, Section 2
Metallized polypropylene films
Jan 2014
88
IS 11298(Part 3/Sec 3):1998
/ IEC 60674-3-2 (1992)
Plastic films for electrical purposes:Part 3
Specifications for individual materials,Section 3
Requirements for balanced biaxially oriented
Polyethylene Terephalate(PET) films used for electrical
insulation
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
9
Jul 2013
1
89
IS 11298(Part 3/Sec 4):1998
/ IEC 60674-3-3(1992)
Plastic films for electrical purposes: Part 3
Specification for individual materials, Section 4
Requirements for polycabonate (PC) films used or
electrical insulation
Jul 2013
90
IS 11298(Part 3/Sec 8):1998
/ IEC 60674-3-7(1992)
Plastic films or electrical purposes: Part 3 Specification
for individual materials, Section 8 Requirements for
fluoroethylene (FEP) films used for electrical insulation
Jul 2013
91
IS 11298(Part 3/Sec 5-7):1998
/ IEC60674-3-4to6(1993
Plastic Films for Electrical Purposes Part 3
Specification for Individual Materials Section 5-7
Requirements for Polyimide Films
Jul 2013
92
IS 11654(Part 1):1986
| IEC 60684-1(1980)
Flexible insulating sleeving:
Part 1 Definitions and general requirements
Oct 2011
93
IS 11654(Part 2):1986
Flexible insulating sleeving: Part 2 Methods of tests
Oct 2011
94
IS 11654(Part 3/Sec 1):1988
Flexible insulating sleeving:
Part 3 Specifications for individual types of sleevings,
Section 1 General purpose grade sleeving with
temperature index 90
Oct 2010
95
IS 11654(Part 3/Sec 103):1989
Flexible insulating sleevings:
Part 3 Specifications for individual types of sleevings,
Section 103 General purpose grade sleeving with
unilateral tolerances with temperature index 90
Oct 2010
96
IS 11654(Part 3/Sec 403):1989
Flexible insulating sleeving: Part 3 Specifications for
individual types of sleevings, Section 403 Glass textile
sleeving with acrylic based coating - High breakdown
strength
Oct 2010
97
IS 11654(Part 3/Sec 404):1989
Flexible insulating sleeving: Part 3 Specifications for
individual types of sleevings, Section 404 Glass textile
sleeving with acrylic based coating - Medium
breakdown strength
Oct 2010
98
IS 11654(Part 3/Sec 405):1989
Flexible insulating sleeving: Part 3 Specifications for
individual types of sleevings, Section 405 Glass textile
sleeving with acrylic based coating - Lower breakdown
strength
Oct 2010
99
IS 11654(Part 3/Sec 406):1989
Flexible insulating sleeving: Part 3 Specifications for
individual type of sleevings, Section 406 Glass textile
sleeving with PVC based coating - High breakdown
strength
Oct 2010
100
IS 11654(Part 3/Sec 407):1989
Flexible insulating sleeving: Part 3 Specifications for
individual type of sleevings, Section 407 Glass textile
sleeving with PVC based coating - Medium breakdown
strength
Oct 2010
101
IS 11654(Part 3/Sec 408):1989
Flexible insulating sleeving: Part 3 Specifications for
individual type of sleevings, Section 408 Glass textile
sleeving with PVC based coating - Lower breakdown
strength
Oct 2010
102
IS 11731(Part 1):1986
| IEC 60107(1981)
Methods of test for determination of flammability of
solid electrical insulating materials when exposed to an
igniting source: Part 1 Horizontal specimen method
Oct 2011
103
IS 11731(Part 2):1986
| IEC 60707(1981)
Methods of test for determination of flammability of
solid electrical insulating materials when exposed to an
igniting source: Part 2 Vertical specimen method
Oct 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
10
1
1
104
IS 11755:1986
| IEC 60345(1971)
Method of test for determination of electrical
resistance and resistivity of insulating materials at
elevated temperatures
Oct 2011
105
IS 11756:1986
| IEC 60648(1979)
Method of test for co-efficients of friction of
plastic film and sheeting for use as electrical insulation
Oct 2011
106
IS 12316(Part 1):1988
Non-cellulosic papers for electrical purposes: Part 1
Definitions and general requirements
Oct 2010
107
IS 12316(Part 2):1988
Non-cellulosic papers for electrical purposes: Part 2
Methods of test
Oct 2010
108
IS 12316(Part 3/Sec 1):1988
Non-cellulosic papers for electrical purposes: Part 3
Requirements for individual materials, Section 1
Unfilled aramid (Aromatic Polyamide) Papers,
calendared
Oct 2010
109
IS 12316(Part 3/Sec 2):1988
Non-cellulosic papers for electrical purposes: Part 3
Requirements for individual materials, Section 2
Unfilled aramid (Aromatic Polyamide) Paper,
uncalendered
Oct 2010
Oct 2010
110
IS 12317(Part 1):1988
| IEC 60672-1(1980)
Ceramic and glass insulating materials for
telecommunication and allied purposes: Part 1 General
requirements and classification of ceramic and glass
insulating materials
111
IS 12747(Part 1):2011
/ IEC 60626-1(2009)
Combined flexible materials for electrical insulation Part 1 Definition and general requirements (First
Revision )
112
IS 12747(Part 2):2012
/ IEC 60626-2:2012
Combined flexible materials for electrical insulation Part 2 Method of test (First Revision)
113
IS 12747(Part 3):2014
/ IEC 60626-3:2008
Combined flexible materials for electrical insulation Part 3: Specifications for individual materials (First
Revision)
114
IS 13066:1991
Prepreg based on glass woven fabric for electrical
applications
Oct 2011
115
IS 13233:1991
Low voltage high current arc resistance test - Method
of test
Oct 2011
116
IS 13335:1992
Muscovite mica scrap for mica paper
Apr 2013
117
IS 13357:1992
Methods of grading and visual classification of
muscovite mica splittings
Apr 2013
118
IS 13465(Part 1):2005
/ IEC 60455-1(1998)
Resin based reactive compounds used for electrical
insulation: Part 1 Definitions and general requirements
(first revision)
Apr 2010
119
IS 13465(Part 2):2005
/ IEC 60455-2(1998)
Resin based reactive compounds used for electrical
insulation: Part 2 Methods of test [first revision]
Sep 2010
120
IS 13465(Part 3/Sec 1):2006
/ IEC 60455-3-1(2003)
Resin based reactive compounds used for electrical
insulation - Part 3: Specification for individual
materials - Section 1: Unfilled epoxy resinous
compounds (first revision)
Apr 2011
121
IS 13465(Part 3/Sec 2):2006
/ IEC 60455-3-2
Resin based reactive compounds used for electrical
insulation - Part 3: Specification for individual
materials - Section 2: Quartz filled epoxy resinous
compounds [first revision)
Apr 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
11
1
122
IS 13465(Part 3/Sec 3):2006
/ IEC 60455-3-3
Resin based reactive compounds used for electrical
insulation - Part 3: Specification for individual
materials - Section 3: Unfilled polyurethane
compounds [first revision)
Apr 2011
123
IS 13465(Part 3/Sec 4):2006
/ IEC 60455-3-4
Resin based reactive compounds used for electrical
insulation - Part 3: Specification for individual
materials - Section 4: Filled polyurethane compounds
(first revision)
Apr 2011
124
IS 13465(Part 3/Sec 5):1998
Solventless polymerisable compounds used for
electrical insulation: Part 3 Specification for individual
materials, Section 5 Epoxy phynol novolac resin
May 2013
125
IS 13465(Part 3/Sec 6):2006
/ IEC 60455-3-5(2001)
Resin based reactive compounds used for electrical
insulation - Part 3: Specification for individual
materials - Section 6: Unsaturated polyester based
impregnating resins
Jul 2011
126
IS 13508:1992
| IEC 60894(1987)
Test procedure for measurement of loss of tangent
angle of coils and bars for machine winding-guide
Feb 2013
127
IS 13884:1993
Muscovite mica flakes and mica powder for industrial
applications
Apr 2013
128
IS 14353:1996
Guide for determining compatibility between enamelled
winding wires and impregnating compounds
Oct 2011
129
IS 14672:1999
Method of test for high voltage, low current
dry arc resistance of solid electrical insulation
Aug 2009
130
IS 15208:2002
Specification for unidirectional fibre glass tape
Sep 2012
131
IS 15218(Part 1):2002
Electrical insulating materials - Determination of the
lonizing radiation: Part 1 Effects of radiation interaction
and dosimetry
Oct 2012
132
IS 15652:2006
Insulating mats for electrical purposes - Specification
(Superseding IS: 5424)
Apr 2011
133
IS 60371(Part 1):2003
Specification for insulating materials based on mica –
Part 1 : Definitions and general requirements
[Superseding IS 9299(Part 1)]
134
IS 60371(Part 2):2004
Specification for insulating materials based on mica –
Part 2 : Methods of test [Superseding IS 9299(Part 2)]
135
IS 60371(Part 3/Sec 1):2006
/ IS/IEC60371-3-1:2006
Specification for insulating materials based on mica –
Part 3: Specification for individual materials – Sheet 1:
Commutator separators and materials (Superseding
IS: 9299(Part 3/Sec 1):1979)
136
IS 60371(Part 3/Sec 2):2005
/ IS/IEC60371-3-2:2005
Specification for insulating materials based on mica Part 3: Specification for individual materials - Sheet 2 :
Mica paper [Superseding IS 9299(Part 3/Sec 7)]
137
IS 60371(Part 3/Sec 3):1983
/ IS/IEC60371-3-3:1983
Specification for insulating materials based on mica –
Part 3: Specification for individual materials – Sheet 3 :
Rigid mica materials for heating equipment
[Superseding IS 9299(Part 3/Sec 4)]
138
IS 60371(Part 3/Sec 4):1992
/ IS/IEC60371-3-4:1992
Specification for insulating materials based on mica –
Part 3: Specification for individual materials – Sheet 4
Polyester film-backed mica Paper with a B-stage
epoxy Resin binder
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
12
1
2
139
IS 60371(Part 3/Sec 5):2005
/ IS/IEC60371-3-5:2005
Specification for insulating materials based on mica –
Part 3: Specification for individual materials – Sheet 5 :
Glass-backed mica paper with an epoxy resin binder
for post- Impregnation (VPI) [Supetseding IS 9299(Part
3/Sec 3)& IS 9299 (Part 3/Sec 5)]
140
IS 60371(Part 3/Sec 6):1992
/ IS/IEC60371-3-6:1992
Specification for insulating materials based on mica –
Part 3: Specification for individual materials – Sheet 6 :
Glass-backed mica paper With a B-stage epoxy resin
binder (Superseding IS: 9299(Part 3/Sec 6):1993)
141
IS 60371(Part 3/Sec 7):1995
/ IS/IEC60371-3-7:1995
Insulating materials based on mica – Part 3 :
Specification for individual materials – Sheet 7 :
Polyester film mica paper with an epoxy resin binder
for single conductor taping [Supetseding IS 9299(Part
3/Sec 3)& IS 9299 (Part 3/Sec 5)]
142
IS 60371(Part 3/Sec 8):1995
/ IS/IEC60371-3-8:1995
Insulating materials based on mica – Part 3 :
Specification for individual materials – Sheet 8 : Mica
paper tapes for flame-resistant security cables
143
IS 60371(Part 3/Sec 9):1995
/ IS/IEC60371-3-9:1995
Insulating materials based on mica – Part 3 :
Specification for individual materials – Sheet 9 :
Moulding micanite [Superseding IS 9299 (Part 3/ Sec
2)]
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 2(6640)
Specification for pressboard and presspaper for
electrical purposes – Part 1: Definitions and general
requirements (IEC 60641-1:2007)
2
DOC.ETD 2(6641)
Specification for pressboard and presspaper for
electrical purposes – Part 2: Methods of tests (IEC
60641-2:2004)
3
DOC.ETD 2(6642)
Pressboard and presspaper for electrical purposes –
Part 3: Specifications for individual materials – Sheet
1: Requirements for pressboard, types b.0.1, b.0.3,
b.2.1, b.2.3, b.3.1, b.3.3, b.4.1, b.4.3, b.5.1, b.5.3 and
b.6.1 (IEC 60641-3-1:2008)
4
DOC.ETD 2(6643)
Specification for pressboard and presspaper for
electrical purposes – Part 3: Specifications for
individual materials – Sheet 2: Requirements for
presspaper, types P.2.1, P.4.1, P.4.2, P.4.3 and P.6.1
(IEC 60641-3-2:2007)
5
DOC.ETD 2(6644)
Laminated pressboard for electrical purposes – Part 1:
Definitions, classification and general requirements
(IEC 60763-1:2010)
6
DOC.ETD 2(6645)
Laminated pressboard for electrical purposes – Part 3:
Specifications for individual materials – Sheet 1:
Requirements for laminated recompressed
pressboard, Types LB3.1A.1 and LB3.1A.2 (IEC 607633-1:2010)
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 2(6682)
Insulating Mats For Electrical Purposes – Specification
(First Revision of IS 15652)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
13
ETD 3 FLUIDS FOR ELECTROTECHNICAL APPLICATIONS
SCOPE - To prepare product specifications, test methods as well as maintenance and
use guides for liquid and gaseous dielectric. Also to prepare specifications
and maintenance and use guides for lubricants and control fluids for
turbines, generators and control systems as well as to assist in the
preparations of test methods for such fluids
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
2
** IS 335:1993
IS 1866:2000
| IEC 60296(1982)
New insulating oils (fourth revision)
Mar 2010
2
Code of practice for maintenance and supervision of
mineral insulating oil in equipment (third revision)
Dec 2010
1
3
IS 6103:1971
Method of test for specific resistance (resistivity) of
electrical insulating liquids
Oct 2011
1
4
IS 6104:1971
Method of test for interfacial tension of oil against
water by the ring method
Oct 2011
1
5
IS 6262:1971
Method of test for power factor and dielectric constant
of electrical insulating liquids
Oct 2011
Method for determination of electric strength of
insulating oils (first revision)
Apr 2013
Method of sampling for liquid dielectrics
Oct 2013
Guide for sampling and analysis of free and dissolved
gases and oil from oil-filled electrical equipment (first
revision)
Apr 2013
Electrical grade castor oil for use as capacitor
impregnant
Oct 2011
6
7
8
9
* IS 6792:1992
| IEC 60156(1963)
IS 6855:2003
* IS 9434:1992
| IEC 60567(1977)
IS 9960:1981
10
IS 10593:2006
/ IEC 60599(1999)
Mineral oil-impregnated electrical equipment in
service - Guide to the interpretation of dissolved and
free gases analysis (second revision)
Sep 2011
11
IS 11549:1986
Impregnating oils and compounds for paper insulated
cables upto 33 kV
Apr 2013
12
IS 11697:1986
Guide for determination of lightning impulse electric
strength of insulating liquids
Oct 2011
Guide for the determination of the aromatic
hydrocarbon content of new insulating oils: Part 1
Absorption chromatographic method
Oct 2011
13
IS 12026(Part 1):1986
| IEC 60590(1977)
14
IS 12026(Part 2):1986
Guide for the determination of the aromatic
hydrocarbon content of new insulating oils: Part 2 Infra
red spectrophotometric method
Oct 2011
15
IS 12177:1987
Methods of tests for oxidative ageing of electrical
insulation of petroleum oils by the open beaker method
Apr 2013
16
* IS 12422:1988
| IEC 60474(1977)
Test method for oxidation stability of inhibited mineral
insulating oils
Apr 2013
17
IS 12463:1988
Inhibited mineral insulating oils
Apr 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
14
2
1
1
18
IS 12475(Part 1):1988
Gassing of insulating liquid under electric stress and
ionization: Part 1 Method of determination of gassing
rate under hydrogen atmosphere
Apr 2013
19
IS 12475(Part 2):1988
Gassing of insulating liquids under electric stress and
ionization: Part 2 Method of determination of gassing
rate under nitrogen atmosphere
Apr 2013
20
IS 12958:1990
Oxidation stability of inhibited mineral insulating oil by
rotating bomb - Method of test
Oct 2011
21
IS 13067:1991
Impregnants for power capacitors
Oct 2011
22
IS 13072:2013
| IEC 60376:2005
Specification of technical grade Sulfur hexafluoride
(SF6) for use In electrical equipment (First Revision)
23
IS 13155:1991
Method of test for carbon type analysis of mineral oils
by infra-red spectrophotometry
24
IS 13236:2013
| IEC 60970:2007
Insulating liquids - methods for counting and sizing
particles (First Revision)
25
IS 13503:2013
/ IEC 61039:2008
Classification of insulating liquids (First Revision)
26
IS 13567:1992
27
Oct 2011
Determination of water in insulating liquids and in oilimpregnated paper and pressboard by automatic
coulometric Karl Fischer titration - Method of test
Apr 2013
* IS 13631:2000
| IEC 60666(1979)
Method of test for detection and determination of
antioxidant additives in insulating oils
Apr 2013
28
IS 15668:2006
/ IEC 61198(1993)
Mineral insulating oils - Methods for the determination
of 2-furfural and related compounds
Jun 2011
29
IS 16081:2013
/ IEC 61099:2010
Insulating liquids - Specifications for unused synthetic
organic esters for electrical purposes
30
IS 16082:2013
| IEC 61619:1997
Insulating liquids - Contamination by polychlorinated
biphenyls (PCBs) - Method of determination by
capillary column gas chromatography
31
IS 16083:2013
| IEC 60465:1988
Specification for unused insulating mineral oils for
cables with oil ducts
32
IS 16085:2013
IS 16085:2013 Mineral oil-filled electrical equipment –
Application of dissolved gas analysis (DGA) to factory
tests on electrical equipment
33
IS 16086:2013
Insulating liquids ─ Determination of the dielectric
dissipation factor by measurement of the conductance
and capacitance ─ Test method
34
IS 16099:2013
Synthetic organic esters for electrical purposes ―
Guide for maintenance of transformer esters in
equipment
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 3(6600)
Insulating liquids — Determination of the breakdown
voltage at power frequency — Test method (Second
Revision of IS 6792) [IEC 60156 (1995)]
2
DOC.ETD 3(6601)
Unused hydrocarbon-based insulating liquids - Test
methods for evaluating the oxidation stability (First
Revision of IS 12422) [IEC 61125 (1992)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
15
1
1
3
DOC.ETD 3(6602)
Detection and determination of specified additives in
mineral insulating oils (First Revision of IS 13631)
[IEC 60666 (2010)]
4
DOC.ETD 3(6603)
Insulating liquids – Contamination by polychlorinated
biphenyls (PCBs) – Method of determination by
capillary column gas chromatography [IEC 61619
(1997)]
5
DOC.ETD 3(6604)
IInsulating liquids – Test method for detection of
potentially corrosive sulphur in used and unused
insulating oil [IEC 62535 (2008)]
6
DOC.ETD 3(6638)
ITest methods for quantitative determination of
corrosive sulphur compounds in unused and used
insulating liquids – Part 1: Test method for quantitative
determination of dibenzyldisulfide (DBDS) [IEC 626971(2012)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
16
ETD 6 ELECTRICAL INSULATORS AND ACCESSORIES
SCOPE - To prepare standards regarding insulated bushing, insulators for overhead
lines, insulators for sub-stations and jointing accessories which are integral
parts of insulators
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 283:1976
Porcelain insulators for telegraph and telephone lines
(third revision)
Jul 2011
4
2
IS 731:1971
Porcelain insulators for overhead power lines with a
nominal voltage greater than 1000 V (second revision)
Jul 2011
7
3
IS 1441:1989
Insulator stalks for telegraph and telephone lines
(second revision)
Apr 2014
4
IS 1445:1977
Porcelain insulators for overhead power lines with a
nominal voltage up to andincluding 1 000 V (second
revision)
Apr 2014
5
5
IS 2099:1986
Bushings for alternating voltages above 1 000 Volts
(second revision)
Apr 2013
2
6
IS 2486(Part 1):1993
Metal fittings of insulators for overhead power lines
with nominal voltage greater than 1000 V Specification :
Part 1 General requirements and tests (first revision)
Apr 2013
7
IS 2486(Part 2):1989
| IEC 120 (1984)
Insulator fittings for overhead power lines with nominal
voltage greater than1000 V - Specification :
Part 2 Dimensional requirements (second revision)
Apr 2014
8
IS 2486(Part 3):1974
| IEC 372-1 (1971)
Specification for Insulator fittings for overhead power
lines with a nominal voltage greter than 1 000 Volts:
Part 3 Locking devices
Jul 2011
9
IS 2486(Part 4):1981
| IEC 372-2 (1976)
Specification for Insulator fittings for overhead power
lines with a nominal voltage greater than1 000 V: Part
4 Test for locking devices
Jul 2011
10
IS 2544:1973
| IEC 168 (1964)
Porcelain post insulators for systems with nominal
voltage greater than 1000 Volts (first revision)
Jul 2011
11
IS 3188:1980
Characteristics of string insulator units (first revision)
Apr 2014
12
IS 3347(Part 1/Sec 1):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 1 Upto and
including 1 kV, Section 1 Porcelain parts (first revision)
Apr 2014
1
13
IS 3347(Part 1/Sec 2):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 1 Up to and
including 1 kV, Section 2 Metal parts (first Revision)
Apr 2014
3
14
IS 3347(Part 2/Sec 1):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 2 3.6 kV
bushings, Section 1 Porcelain Parts (first revision)
Apr 2014
1
15
IS 3347(Part 2/Sec 2):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 2 3.6 kV
bushings, Section 2 Metal parts (first revision)
Apr 2014
3
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
17
4
16
IS 3347(Part 3/Sec 1):1988
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 3 17.5 kV
bushings, Section 1 Porcelain parts (second revision)
Apr 2014
17
IS 3347(Part 3/Sec 2):1982
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 3 17.5 kV
bushings, Section 2 Metal parts (first revision)
Apr 2014
2
18
IS 3347(Part 4/Sec 1):1988
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 4 24 kV bushings,
Section 1 Porcelain parts (Second revision)
Apr 2014
1
19
IS 3347(Part 4/Sec 2):1982
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 4 24 kV
bushings, Section 2 Metal Parts (first revision
Apr 2014
3
20
IS 3347(Part 5/Sec 1):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 5 36 kV
bushings, Section 1 Porcelain parts (second revision)
Apr 2014
1
21
IS 3347(Part 5/Sec 2):1979
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 5 36 kV
bushings, Section 2 Metal parts (first revision)
Apr 2014
2
22
IS 3347(Part 8/Sec 1):1988
Dimensions for procelain transformer bushings for use
in lightly polluted atmospheres: Part 8 52 kV bushings,
Section 1 Porcelain parts
Apr 2014
23
IS 3347(Part 8/Sec 2):1992
Dimensions for porcelain transformer bushings for use
in lightly polluted atmospheres: Part 8 52 kV bushings:
Section 2 Metal parts
Apr 2014
24
IS 4257(Part 1):1981
Dimensions for clamping arrangements for porcelain
transformer bushings: Part 1 For 12 kV to 36 kV
bushings (first revision)
Apr 2014
25
IS 4257(Part 2):1986
Dimensions for clamping arrangements for porcelain
transformer bushings: Part 2 For 72.5 kV and 123 kV
bushings
Apr 2014
26
IS 4318:1993
Solid core porcelain insulators for overhead traction
lines (first revision)
Apr 2013
27
IS 5300:1969
Specification for porcelain guy strain insulators
Apr 2014
1
28
IS 5350(Part 1):1970
| IEC 273 (1968)
Dimensions of indoor and outdoor porcelain post
insulator and post insulator units for system with
nominal voltage greater than 1000 V: Part 1 Indoor
post insulators
Apr 2014
29
** IS 5350(Part 2):1973
Dimensions of indoor and outdoor porcelain post
insulators and post insulator units for system with
nominal voltage greater than 1000 V: Part 2 Outdoor
cylindrical post insulators
Apr 2014
30
IS 5350(Part 3):1971
| IEC 273 (1968)
Dimensions of indoor and outdoor porcelain post
insulators and post insulator units for system with
nominal voltages greater than 1000 V: Part 3 Outdoor
pedestal post insulators
Apr 2014
3
2
31
IS 5621:1980
Hollow insulators for use in electrical equipment (first
revision)
Apr 2014
32
IS 7421:1988
Porcelain bushings for alternating voltage upto and
including 1000 V (first revision)
Apr 2014
33
IS 7648:1975
Silicone compound for application on high voltage
porcelain insulators
Apr 2014
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
18
2
34
IS 7935:1975
Insulator fittings for overhead power lines with a
nominal voltage upto and including 1000 V
Jul 2011
35
IS 8263:1976
Methods for radio interference test on high voltage
insulators
Apr 2014
36
IS 8269:1976
Methods for switching impulse tests on high voltage
insulators
Apr 2014
37
IS 8603:2008
Dimensions for procelain transformers bushings for
use heavily polluted atmospheres 12/17.5kv, 24kv and
36 kv (First revision of IS 8603 (Part 1,2 & 3 combined)
Sep 2013
38
IS 8603(Part 4):2003
Dimensions for porcelain transformers bushings for
use in heavily polluted atmospheres: Part 4 52 kV
bushings
Oct 2013
Artificial pollution on high voltage insulators to be used
on ac systems (first revision)
Oct 2011
39
IS 8704:1995
| IEC 507 (1991)
40
IS 8765:1978
Ceramic insulating materials for electrical purposes
Apr 2014
41
IS 9431:1979
Indoor post insulators of organic material for systems
with nominal voltages greater than 1 000 V upto and
including 300 kV
Apr 2014
42
IS 10136:1982
Code of practice for selection of disc insulator fittings
for highest system voltages of 72.5 kV and above
Jul 2011
43
IS 10314:1982
Dimensions for ceramic bushings for terminals
Jul 2011
44
IS 12676:1989
Oil impregnated paper insulated condenser bushings Dimensions and requirements
Jul 2011
45
IS 13134:1992
Guide for the selection of insulators in respect of
pollution conditions
Apr 2013
46
IS 13305:1992
Permissible limits of visual defects for insulating
porcelains for electrical circuits
Apr 2013
47
IS 13312:1992
Dimensions of porcelain oil filled transformer bushings
(rated 52 kV) for medium polluted atmospheres
Apr 2013
48
IS 15137:2002
Metal Connecting Lugs for Porcelain Transformer
Bushings - Specification
Dec 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 6(6338)
/ IEC 60372 : 1984
Locking Devices for ball and socket couplings of string
insulators units. Dimensions and tests
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
19
3
1
ETD 7 LOW VOLTAGE SWITCHGEAR & CONTROLGEAR
SCOPE - To prepare standards for switchgear and controlgear such as circuit
breakers, switches, contactors, starters, disconnectors, bus bars, fuse
combination units and semiconductors connectors and any switchgear
assemblies for voltages upto and including 1 000 V ac or 1 200 V dc
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1356(Part 1):1972
| IEC 60204-1
Electrical equipment of machine tools:
Part 1 Electrical equipment of machines
for general use (second revision)
Mar 2011
2
IS 2675:1983
Enclosed distribution fuseboards and cutouts for
voltages not exceeding 1000 V (second revision)
Mar 2011
3
IS 5039:1983
Distribution pillars for voltages not
exceeding 1 000 volts (first revision)
Mar 2011
4
IS 8588(Part 1):1977
Thermostatic bimetals:
Part 1 General requirements and methods of tests
Mar 2013
5
IS 8623(Part 1):1993
/ IEC 60439-1(1985)
Specification for low voltage switchgear
and controlgear assemblies:
Part 1 Requirements for type-tested
and partially type tested assemblies (first revision).
Mar 2013
6
IS 8623(Part 2):1993
/ IEC 60439-2(1987)
Specification for low voltage switchgear
and controlgear assemblies:
Part 2 Particular requirements for busbar
trunking systems (busways)-(first revision)
Mar 2013
7
IS 8623(Part 3):1993
/ IEC 60439-3(1990)
Low-voltage switchgear and controlgear assemblies:
Part 3 Particular requirements for equipment where
unskilled persons have access for their use.
Mar 2013
8
IS 10027:2000
Composite units of air-break switches and rewirable
type fuses for voltages not exceeding 650 volt ac Specification (first revision)
Mar 2010
9
IS 12021:1987
Specification for control transformers for switchgear
and controlgear for voltages not exceeding 1000 Volt
ac
Mar 2010
10
IS 12640(Part 1):2008
/ IEC 61008-1:1996
Residual current operated circuit-breakers for
household and simililar uses : Part 1 circuit-breakers
without integral overcurrent protection(RCCBs) (First
Revision)
Apr 2013
11
IS 12640(Part 2):2008
/ IEC 61009-1:1996
Residual current operated circuit breakers for
household and similar uses: Part 2 circuit breakers
with integral overcurrent protection(RCBOs) (First
Revision)
Apr 2013
Miniature circuit breaker boards for
voltage upto and including 1 000 Volt ac
Mar 2011
12
IS 13032:1991
13
IS 13947(Part 5/Sec 2):2004
/ IEC 60947-5-2(2000)
Low voltage switchgear and controlgear :
Part 5 Control circuit devices and switching elements
Section 2 Proximity switches
Jun 2009
14
IS 14577:1998
/ IEC 60363(1998)
Short-circuit current evaluation with special regard to
rated short-circuit capacity of circuit-breakers in
installations in ships
Jun 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
20
1
2
1
15
IS 14614:1998
/ IEC 61543(1995)
Residual Current Operated Protective
Devices (RCDs) for household and similar use Electromagnetic compatibility.
Mar 2013
16
IS 60715:1981
/ IS/IEC 60715:1981
Dimensions of Low-voltage swtichgear and
controlgear - Standardized mounting on rails of
mechanical support of electrical devices in switchgear
and controlgear installations(Superseding IS 11039)
Oct 2012
17
IS 60898(Part 1):2002
/ IS/IEC 60898-1:2002
Electrical Accessories - circuit breakers for over
May 2013
protection for household and similar installations Part 1
Circuit breakers for a.c. . operation ( Superseding IS
8828)
18
IS 60898(Part 2):2003
/ IS/IEC 60898-2:2003
Electrical Accessories - circuit breakers for over
protection for household and similar installations Part 2
Circuit breakers for a.c. and d.c. operation
Sep 2012
19
IS 60947(Part 1):2007
/ IS/IEC 60947-1:2007
Low voltage switchgear and controlgear: Part 1
General Rules (Superseding IS 13947(Part 1) (IEC
60947-1(2007)) (First Revision)
Apr 2012
20
IS 60947(Part 2):2003
/ IS/IEC 60947-2:2003
Low voltage switchgear and controlgear: Part 2 Circuit
breakers[Superseding IS 13947( Part 2 ):1993]
Dec 2012
21
IS 60947(Part 3):1999
/ IS/IEC 60947-3:1999
Low voltage switchgear and controlgear : Part 3
Switches, disconnectors, switch-disconnectors and
fuse combination units [Superseding IS 13947(Part 3)]
Apr 2013
22
IS 60947(Part 4/Sec 1):2000
/ ISIEC 60947-4-1:2000
Low-Voltage switchgear and controlgear: Part 4
Contactors and motor starters,Section 1
Electromechanical contactors and motor
starters[superseding IS 13947(Part 4/Sec 1)
Jul 2013
23
IS 60947(Part 4/Sec 2):1999
/ ISIEC 60947-4-2:1999
Low voltage switchgear and controlgear: Part 4
Contactors and motors starters Section 2 ac
Semiconductor Motor Controllers and Starters
Oct 2012
24
IS 60947(Part 4/Sec 3):1999
/ ISIEC 60947-4-3:1999
Low voltage switchgear and controlgear :Part 4
Contactors and motor starters Section 3 AC
semiconductor controllers and contactors for nonmotor loads
May 2013
25
IS 60947(Part 5/Sec 1):2003
/ ISIEC 60947-5-1:2003
Low-voltage switchgear and controlgear: Part 5 Control circuit devices and switching elements,
Section 1 Electromechanical control circuit devices
(Sperseding of IS 13947 Part 5/Sec 1)
May 2013
26
IS 60947(Part 5/Sec 2):2007
Low voltage switchgear and controlgear :
Part 5 Control circuit devices and switching elements
Section 2 Proximity switches (60947-5-2:2007)
May 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 7(6584)
Low voltage switchgear and controlgear assemblies Part 0: Guidance to specifying Assmeblies
[Superseding IS 8623(Part 1):2008(IEC 61439-0:2010)
2
DOC.ETD 7(6586)
/ IEC 61439-2 : 2011
Low voltage switchgear and controlgear assemblies Part 2 : Power Switchgear And Controlgear
Assemblies (Superseding IS 8623 (Part 1) : 1993 and
IS 2675 : 1993 (IEC 61439-2:2011)
3
DOC.ETD 7(6587)
Low voltage surge protective devices - Part 11: Surge
protective devices connected to low-voltage power
distribution systems (IEC 61643-11:2011)
4
DOC.ETD 7(6334)
Specification for control transformers for switchgear
and controlgear for voltages not exceeding 1000 Volt
ac (First Revision of iS 12021)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
21
2001
5
DOC.ETD 7(6583)
/ IEC 61009-1:2012
Residual current operated circuit breakers with
integral overcurrent protection for household and
similar uses (RCBOs) : Part 1 General rules
[Superseding IS 12640(Part 2): 2008]
6
DOC.ETD 7(6585)
/ IEC 61439-1:2011
Low voltage switchgear and controlgear assemblies Part 1: General rules [Superseding IS 8623(Part
1):1993(IEC 61439-1:2011)
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 7(6256)
Low-Voltage switchgear and controlgear: Part 4
Contactors and motor starters,Section 1
Electromechanical contactors and motor
starters[superseding IS 13947(Part 4/Sec 1) (IEC
60947-4-1:2009, Ed 3.0)
2
DOC.ETD 7(6257)
Amendment No. 1 to IS/IEC 60947-5-1:2003 Lowvoltage switchgear and controlgear: Part 5 Control circuit devices and switching elements,
Section 1 Electromechanical control circuit devices
3
DOC.ETD 7(6311)
Low voltage surge protective devices - Part 12 : Surge
protective devices connected to low-voltage power
distribution systems - Selection and application
principles (IEC 61643-12:2008)
4
DOC.ETD 7(6582)
/ IEC 61008-1:2012
Residual current operated circuit breakers without
integral overcurrent protection for household and
similar uses (RCCBs) : Part 1 General rules
[Superseding IS 12640(Part 1): 2008]
5
DOC.ETD 7(6729)
/ (IEC 60947-2 (2013)
Low voltage switchgear and controlgear: Part 2 Circuit
breakers) (First Revision)
6
DOC.ETD 7(6730)
/ IEC 60947-3 (2012)
Low voltage switchgear and controlgear :
Part 3 Switches, disconnectors, switch-disconnectors
and fuse combination units (First Revision)
7
DOC.ETD 7(6613)
/ IEC 60947-4-2:2011
Low voltage switchgear and controlgear: Part 4
Contactors and motors starters Section 2 ac
Semiconductor Motor Controllers and Starters (First
Revision)
8
DOC.ETD 7(6614)
/ IEC 60947-4-3:2011
Low voltage switchgear and controlgear :Part 4
Contactors and motor starters Section 3 AC
semiconductor controllers and contactors for nonmotor loads (First Revision)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 7(6332)
Draft Guidelines for application of aluminum
conductors for low voltage switchgear and controlgear
as per IS/IEC 60947-1
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
22
ETD 8 HIGH VOLTAGE SWITCHGEAR AND CONTROLGEAR
SCOPE - To prepare standards for switchgear and controlgear; such as circuit
breakers, switches contactors, starters, disconnectors, busbars and any
switchgear assemblies for voltages more than 1000 V ac
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 3427:1997
/ IEC 60298:1990
A.C. Metal enclosed switchgear and controlgear for
rated voltages above 1kV upto and including 52
kV(first revision)
Sep 2012
2
IS 5561:1970
Electric power connectors
Sep 2012
3
IS 7567:1993
Automatic circuit reclosers(second revision)
Sep 2012
4
IS 8084:1976
Interconnecting busbars for ac voltage above 1 kV
upto and including 36 kV
Sep 2012
5
IS 9135:1979
Guide for testing of circuit breakers with respect to outof-phase switching
Sep 2012
6
* IS 9920(Part 1):2002
/ IEC 60265:1998
High Voltage Switches - Part 1 : Switches for Rated
Voltages Above 1 kV and Less Than 52 KV
Sep 2012
7
IS 9920(Part 2):2001
/ IEC 60265-2:1988
High voltage switches : Part 2 High voltage switches
for rated voltages of 52 kV and above (First revision)
Mar 2011
8
* IS 9920(Part 3):1982
| IEC 60129:1975
Switches and switch isolators for voltages above 1000
V: Part 3 Design and construction
Sep 2012
9
* IS 9920(Part 4):1985
| IEC 60129:1975
Switches and switch isolators for voltages above 1000
V: Part 4 Type tests and routine tests
Sep 2012
10
* IS 9921(Part 1):1981
| IEC 60129:1975
Alternating current disconnectors (isolators) and
earthing switches for voltages above 1000 V: Part 1
General and definitions
Sep 2012
11
* IS 9921(Part 2):1982
| IEC 60129:1975
Alternating current disconnectors (isolators) and
earthing switches for voltages above 1000 V: Part 2
Rating
Sep 2012
12
* IS 9921(Part 3):1982
| IEC 60129:1975
Alternating current disconnectors (isolators and
earthing switches for voltages above 1 000 V: Part 3
Design and construction
Sep 2012
13
* IS 9921(Part 4):1985
| IEC 60129:1975
Alternating current disconnectors (isolators) and
earthing switches for voltages above 1000 V: Part 4
Type tests and routine tests
Sep 2012
14
* IS 9921(Part 5):1985
| IEC 60129:1975
Alternating current disconnectors (isolators) and
earthing switches for voltages above 1 000 V: Part 5
Information to be given with tenders, inquiries and
orders
Sep 2012
Dimensions of terminals of high voltage switchgear
and controlgear
Oct 2010
Methods of synthetic testing of high voltage alternating
current circuit breakers
Apr 2013
15
IS 10601:1983
16
IS 13516:1993
/ IEC 60427:1989
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
23
1
17
IS 14657:1998
/ IEC 61259:1994
Gas-insulated metal-enclosed switchgear for rated
voltage 72.5 kV and above - requirements for
switching of bus-charging current by disconnectors.
Apr 2013
18
IS 14658:1999
/ IEC 61633:1995
High-voltage alternating current circuit-breakers- Guide
for short-circuit and switching test procedures for
metal-enclosed and dead tank circuit-breakers
Apr 2014
19
IS 14659:1999
/ IEC 60466:1987
A.C. insulation-enclosed switchgear and controlgear
for rated voltage above 1 kV and upto and including 38
kV
Apr 2014
20
IS 14666:1999
/ IEC 60420:1990
High voltage alternating current switch fuse
combinations
Apr 2014
21
IS 14674:1999
/ IEC 61166:1993
High voltage alternating current circuit breakersGuide for seismic qualifications of high-voltage
alternating current circuit-breakers
Apr 2014
22
IS 14786:2000
/ IEC 61330:1995
High voltage/ low voltage prefabricated substations
Mar 2010
23
IS 60470:2000
/ IS/IEC 60470:2000
High Voltage Alternating Current Contactors and
Contactor-Based Motor-Starters (superseeding IS
9046:1978 and IS 12661(Part 1):1988
May 2014
24
IS 60517:1990
/ IS/IEC 60517:1990
Gas insulated metal enclosed switchgear for rated
voltages of 72.5 KV and above
Sep 2012
25
IS 62271(Part 1):2007
/ IEC 62271-1 :2007
High-voltage switchgear and controlgear:
Part 1 Common Specification (IEC 62271-1 :2007)
(Superseding IS 12729)
Sep 2013
26
IS 62271(Part 100):2008
/ IEC 62271-100 :2008
High-voltageswitchgear and controlgear:
Part 100 Alternating current Circuit Breakers(IEC
62271-100 :2008)
Oct 2012
27
IS 62271(Part 102):2003
/ IS/IEC62271-102:2003
High-voltage switchgear and controlgear:
Part 102 High-voltage alternating current circuit
breakers
Oct 2013
28
IS 62271(Part 105):2002
/ IS/IEC62271-105:2002
High-voltageswitchgear and controlgear:
Part 105 Alternating current switch-fuse combinations
Sep 2013
29
IS 62271(Part 109):2008
/ IEC 62271-109 : 2008
High-voltag switchgear and controlgear:
Part 109 Alternating current Series Capacitor by pass
Switches (IEC 62271-109 :2008)
Oct 2012
30
IS 62271(Part 200):2003
/ IS/IEC62271-200:2003
High-voltage switchgear and controlgear: Part 200 AC
Metal-Enclosed Switchgear and Controlgear for Rated
Voltages Above 1 kV and Up To and Including 52 kV
Sep 2013
31
IS 62271(Part 201):2006
/ IS/IEC62271-201:2006
High-voltage switchgear and controlgear: Part 201 AC
Insulation Enclosed Switchgear and Controlgear for
Rated Voltages Above 1 kV and Above 52 kV
Apr 2014
32
IS 62271(Part 203):2003
/ ISIEC 62271-203:2003
High-voltage switchgear and controlgear: Part 203
Gas-insulated metal-enclosed switchgear for rated
voltages above 52 kV
Apr 2013
33
IS 62271(Part 207):2000
High-Voltage switchgear and controlgear: Part 207
Seismic qualification for gas-insulated switchgear
assemblies for rated voltages above 52 kV (IEC
62271-207)
Dec 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
24
ETD 9 POWER CABLES
SCOPE - To prepare standards for electric cables and their accessories, without
limitations of voltage, current or form of construction but excluding cables for
telecommunications and electronic equipment and such other cables as fall
within the scope of other committees
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 692:1994
Paper insulated lead-sheathed cables for rated
voltages upto and including 33 kV (third revision)
2
IS 694:2010
Polyvinyl chloride insulated sheathed and unsheathed
cables with rigid and flexible conductor for rated
voltages upto and including 450/750 V : Part 1 General
requirements (fourth revision)
3
4
IS 694:1990
| IEC 60227-1to5:1979
IS 1255:1983
Feb 2010
2
1
PVC Insulated cables for working voltages upto and
including 1100 V (Third revision)
Feb 2010
Code of practice for installation and maintenance of
power cables upto and including 33 kV rating (second
revision)
Nov 2011
5
5
IS 1554(Part 1):1988
| IEC 60502:1983
PVC insulated (heavy duty) electric cables: Part 1 For
working voltages upto and including 1 100 V (third
revision)
Feb 2010
5
6
IS 1554(Part 2):1988
| IEC 60502:1983
PVC insulated (heavy duty) electric cables:Part 2 For
working voltages from 3.3kV upto and including 11 kV
(Second revision)
Feb 2010
4
7
IS 2465:1984
Cables for motor vehicles (second revision)
Nov 2011
1
8
IS 2593:1984
Flexible cables for miners' cap lamps (first revision)
Nov 2011
1
9
IS 3961(Part 1):1967
Recommended current ratings for cables: Part 1 Paper
insulated lead sheathed cables
Nov 2011
1
10
IS 3961(Part 2):2014
Recommended current ratings for cables: Part 2 PVC
insulated and PVC sheathed heavy duty cables (First
revision of)
Nov 2011
2
11
IS 3961(Part 3):1968
Recommended current ratings for cables: Part 3
Rubber insulated cables
Nov 2011
1
12
IS 3961(Part 5):1968
Recommended current ratings for cables: Part 5 PVC
insulated light duty cables
Nov 2011
13
IS 3961(Part 6):2014
Recommended current ratings for cables - Part 6 :
Crosslinked polyethylene insulated PVC sheathed
cables
14
IS 3961(Part 7):2014
Recommended current ratings for cables - Part 7 :
Crosslinked polyethylene insulated thermoplastic
sheathed cables
15
IS 4289(Part 1):1984
| IEC 60245-5
Flexible cables for lifts and other flexible connections:
Part 1 Elastomer insulated cables (first revision)
Nov 2011
16
IS 4289(Part 2):2000
| IEC 60227-6:1985
Flexible cables for lifts and other flexible
Connections:Part 2 PVC insulated cables
Feb 2010
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
25
17
18
19
20
21
IS 5819:1970
IS 5831:1984
| IEC 60502:1983
IS 5950:1984
IS 6380:1984
| IEC 60502:1983
IS 6554:1983
Recommended short-circuit ratings of high voltage
PVC cables
Nov 2011
PVC insulation and sheath of electric cables (first
revision)
Nov 2011
Shot firing cables (for use other than in shafts) (first
revision)
Nov 2011
Elastomeric insulation and sheath of electric cables
(first revison)
Nov 2011
1
Soldering ferrules of straight through joints (first
revision)
Nov 2011
1
Feb 2010
5
22
IS 7098(Part 1):1988
| IEC 60502:1983
Cross-linked polyethylene insulated thermosplastic
sheathed cables - Specification : Part 1 For working
voltages upto and including 1 100 V (first revision)
23
IS 7098(Part 2):2011
| IEC 60502-2:2005
Crosslinked polyethylene insulated thermoplastic
sheathed cables - Specification : Part 2 For working
voltages from 3.3 kV upto and including 33 kV (second
revision)
24
IS 7098(Part 3):1993
Crosslinked polyethylene insulated thermoplastic
sheathed cables: Part 3 For working voltages from 66
kV upto and including 220 kV
25
* IS 8130:2013
| IEC 60228:1978
2
2
Dec 2013
4
Conductors for insulated electric cables and flexible
cords (second revision)
26
IS 8308:1993
Compression type tubular in-line connectors for
Dec 2013
aluminium conductors of insulated cables (first revision)
27
IS 8309:1993
Compression type tubular terminal ends for aluminium
conductors of insulated cables (first revision)
Dec 2013
1
28
IS 8337:1976
Performance requirements of compression joints of
aluminium conductors in insulated cables
Feb 2010
1
29
IS 8394:1977
Soldering and welding type terminal ends for
conductors of insulated cables
Aug 2012
2
30
IS 8438:1987
Moulds of cast resin based straight through joints for
cables for voltages upto and including 1 100 V (first
revision)
Aug 2012
31
IS 9553:1987
Moulds suitable for cast resin based terminations for
cables for voltages upto and including 1 100 V (first
revision)
Aug 2012
32
IS 9646:1992
Moulds suitable for cast resin-based joints for cables
for voltages upto and including 1 100 V (first revision)
Dec 2013
33
IS 9857:1990
| IEC 60245-6
Welding cables (first revision)
Feb 2010
1
34
IS 9968(Part 1):1988
Elastomer insulated cables:Part 1 For working
voltages upto and including 1 100 V (first revision)
[superseeding IS 434(Parts 1 and 2)]
Feb 2010
2
35
IS 9968(Part 2):2002
Specification for elastomer-insulated cables:Part 2 For
working voltages from 3.3 kV upto and including 33 kV
(first revision) (superseding IS:434(Parts 1 and 2)
Aug 2012
2
36
IS 10418:1982
Drums for electric cables
Nov 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
26
37
IS 10435(Part 1):1983
Inverted type cable end boxes for outdoor termination
suitable for paper insulated cables : Part 1 Belted type,
multi-core cables upto and including 11 kV grade
Nov 2011
38
IS 10462(Part 1):1983
| IEC 60502:1978
Fictitious calculation method for determination of
dimensions of protective coverings of cables:Part 1
Elastomeric and thermoplastic insulated cables
Nov 2011
39
IS 10462(Part 2):1991
| IEC 60055-2
Fictitious calculation method for determination of
dimensions of protective coverings of cables: Part 2
Paper insulated cables
Nov 2011
40
IS 10606:1983
Cast iron joint boxes for tee and branch trouser joints
suitable for paper insulated cables for voltages upto
and including 11 kV
Nov 2011
41
IS 10810(Part 0):1984
Methods of test for cables: Part 0 General
Nov 2011
42
IS 10810(Part 1):1984
Methods of test for cables: Part 1 Annealing test for
wires used in conductors
Nov 2011
43
IS 10810(Part 2):1984
Methods of test for cables: Part 2 Tensile test for
aluminium wires
Nov 2011
44
IS 10810(Part 3):1984
Methods of test for cables: Part 3 Wrapping test for
aluminium wires
Nov 2011
45
IS 10810(Part 4):1984
Methods of test for cables: Part 4 Persulphate test of
conductor
Nov 2011
46
IS 10810(Part 5):1984
Methods of test for cables: Part 5 Conductor
resistance test
Nov 2011
47
IS 10810(Part 6):1984
Methods of test for cables: Part 6 Thickness of
thermoplastic and elastomeric insulation and sheath
Nov 2011
48
IS 10810(Part 7):1984
Methods of test for cables: Part 7 Tensile strength and
elongation at break of thermoplastic and elastomeric
insulation and sheath
Nov 2011
49
IS 10810(Part 8):1984
Methods of test for cables: Part 8 Breaking strength
and elongation at break for impregnated paper
insulation
Nov 2011
50
IS 10810(Part 9):1984
Methods of test for cables: Part 9 Tear resistance for
paper insulation
Nov 2011
51
IS 10810(Part 10):1984
Methods of test for cables:Part 10 Loss of mass test
Nov 2011
52
IS 10810(Part 11):1984
Methods of test for cables:Part 11 Thermal ageing in
air
Nov 2011
53
IS 10810(Part 12):1984
Methods of test for cables:Part 12 Shrinkage test
Nov 2011
54
IS 10810(Part 13):1984
Methods of test for cables:Part 13 Ozone resistance
test
Nov 2011
55
IS 10810(Part 14):1984
Methods of test for cables:Part 14 Heat shock test
Nov 2011
56
IS 10810(Part 15):1984
Methods of test for cables:Part 15 Hot deformation test
Nov 2011
57
IS 10810(Part 16):1986
Methods of test for cables:Part 16 Accelerated ageing
test by oxygen pressure method
Nov 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
27
58
IS 10810(Part 17):1986
Methods of test for cables: Part 17 Tear resistance test
for heavy duty sheath
Nov 2011
59
IS 10810(Part 19):1984
Methods of test for cables:Part 19 Bleeding and
blooming test
Nov 2011
60
IS 10810(Part 20):1984
Methods of test for cables:Part 20 Cold bend test
Nov 2011
61
IS 10810(Part 21):1984
Methods of test for cables:Part 21 Cold impact test
Nov 2011
62
IS 10810(Part 22):1984
Methods of test for cables:Part 22 Vicat softening point
Nov 2011
63
IS 10810(Part 23):1984
Methods of test for cables:Part 23 Melt-flow index
Nov 2011
64
IS 10810(Part 24):1984
Methods of test for cables:Part 24 Water soluble
impurities test of insulating paper
Nov 2011
65
IS 10810(Part 25):1984
Methods of test for cables:Part 25 Conductivity of
water extract test of insulating paper
Nov 2011
66
IS 10810(Part 26):1984
Methods of test for cables:Part 26 pH value of water
extract test of insulating paper
Nov 2011
67
IS 10810(Part 27):1984
Methods of test for cables:Part 27 Ash content test of
insulating paper
Nov 2011
68
IS 10810(Part 28):1984
Methods of test for cables:Part 28 Water absorption
test (Electrical)
Nov 2011
69
IS 10810(Part 29):1984
Methods of test for cables:Part 29 Environmental
stress cracking test
Nov 2011
70
IS 10810(Part 30):1984
Methods of test for cables:Part 30 Hot set test
Nov 2011
71
IS 10810(Part 31):1984
Methods of test for cables:Part 31 Oil resistance test
Nov 2011
72
IS 10810(Part 32):1984
Methods of test for cables:Part 32 Carbon content test
for polyethylene
Nov 2011
73
IS 10810(Part 33):1984
Methods of test for cables:Part 33 Water absorption
test (Gravimetric)
Nov 2011
74
IS 10810(Part 34):1984
Methods of test for cables:Part 34 Measurement of
thickness of metallic sheath
Nov 2011
75
IS 10810(Part 35):1984
Methods of test for cables:Part 35 Determination of tin
in lead alloy for sheathing
Nov 2011
76
IS 10810(Part 36):1984
Methods of test for cables:Part 36 Dimensions of
armouring material
Nov 2011
77
IS 10810(Part 37):1984
Methods of test for cables:Part 37 Tensile strength and
elongation at break of armouring materials
Nov 2011
78
IS 10810(Part 38):1984
Methods of test for cables:Part 38 Torsion test on
galvanized steel wires for armouring
Nov 2011
79
IS 10810(Part 39):1984
Methods of test for cables:Part 39 Winding test on
galvanized steel strips for armouring
Nov 2011
80
IS 10810(Part 40):1984
Methods of test for cables:Part 40 Uniformity of zinc
coating on steel armour
Nov 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
28
2
1
81
IS 10810(Part 41):1984
Methods of test for cables:Part 41 Mass of zinc
coating on steel armour
Nov 2011
82
IS 10810(Part 42):1984
Methods of test for cables:Part 42 Resistivity test of
armour wires and strips and conductance test of
armour (wires/strips)
Nov 2011
83
IS 10810(Part 43):1984
Methods of test for cables:Part 43 Insulation resistance Nov 2011
84
IS 10810(Part 44):1984
Methods of test for cables:Part 44 Spark test
Nov 2011
85
IS 10810(Part 45):1984
Methods of test for cables:Part 45 High voltage test
Nov 2011
86
IS 10810(Part 46):1984
Methods of test for cables:Part 46 Partial discharge test Nov 2011
87
IS 10810(Part 47):1984
Methods of test for cables:Part 47 Impulse test
May 2010
88
IS 10810(Part 48):1984
Methods of test for cables:Part 48 Dielectric power
factor test
Nov 2011
89
IS 10810(Part 49):1984
Methods of test for cables:Part 49 Heating cycle test
Nov 2011
90
IS 10810(Part 50):1984
Methods of test for cables:Part 50 Bending test
Nov 2011
91
IS 10810(Part 51):1984
Methods of test for cables:Part 51 Dripping test
Nov 2011
92
IS 10810(Part 52):1984
Methods of test for cables:Part 52 Drainage test
Nov 2011
93
IS 10810(Part 53):1984
Methods of test for cables:Part 53 Flammability test
Nov 2011
94
IS 10810(Part 54):1984
Methods of test for cables:Part 54 Static flexibility test
Nov 2011
95
IS 10810(Part 55):1986
Methods of test for cables:Part 55 Abrasion test
Nov 2011
96
IS 10810(Part 56):1987
Methods of test for cables: Part 56 Accelerated ageing
by air-pressure method
Aug 2012
97
IS 10810(Part 57):1987
Methods of test for cables: Part 57 Flexing test
Aug 2012
98
IS 10810(Part 58):1998
Methods of test for cables: Part 58 Oxygen index test
Dec 2013
99
IS 10810(Part 59):1988
Methods of test for cables: Part 59 Determination of
the amount of halogen acid gas evolved during
combustion of polymeric materials taken from cables
May 2010
100
IS 10810(Part 60):1988
Methods of test for cables: Part 60 Thermal stability of
PVC insulation and sheath
May 2010
101
IS 10810(Part 61):1988
Methods of test for cables: Part 61 Flame retardant
test
May 2010
102
IS 10810(Part 62):1993
Methods of test for cables: Part 62 Fire resistance test
for bunched cables
Dec 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
29
1
1
1
103
IS 10810(Part 63):1993
Methods of test for cables: Part 63 Smoke density of
electric cables under fire conditions
Dec 2013
104
IS 10810(Part 64):2003
Methods of test for cables :Part 64 Measurement of
temperature index
Mar 2013
105
IS 10877:1984
Moulds suitable for cast resin based indoor
terminations for cables for voltages 3.3 kV and above
and upto and including 11 kV
Nov 2011
106
IS 11979:1987
Moulds for cast resin based straight through joints for
cables for working voltages from 3.3 kV upto and
including 11 kV
Aug 2012
107
IS 12909:1990
Power cables dimensions for moulds for cast resin
based outdoor terminations for cables for voltages
above 1 100 volts and upto and including 11 000 volts
Feb 2010
108
IS 12943:1990
Brass glands for PVC cables
Feb 2010
109
IS 13573(Part 1):2011
Specification for cable accessories for exturded power
cable with rated voltage up to and including 3.3 kV (E)
Part 1 Test requirements and test methods (First
Revision of IS 13573)
110
IS 13573(Part 2):2011
Specification for cable accessories for exturded power
cable with rated voltage up to and including 3.3 Kv (E)
Part 2 Test requirements (First Revision of IS 13573)
111
IS 13573(Part 3):2011
Specification for cable accessories for exturded power
cable with rated voltage up to and including 3.3 kV (E)
Part 3 Test methods (First Revision of IS 13573)
112
IS 13705:1993
Performance requirements and type test for transition
joint of cables for working voltages from 11 kV up to
and including 33 kV
Dec 2013
113
IS 14255:1995
Aerial bunched cables for working voltages upto and
including 1 100 volts- specification
Feb 2010
114
IS 14494:1998
Elastomer insultated flexible cables for use in mines
(superseeding IS:691 and IS:1026)
Dec 2013
115
IS 16246:2014
Specification for elastomer insulated cables with
limited circuit integrity when affected by fire.
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 9(6037)
Specification for recommended short circuit ratings of
electric cables with rated voltage from 1.1 kV to 220 kV
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 9(5882)
Elastomer insultated flexible cables for use in mines
(first revision of IS 14494)
2
DOC.ETD 9(6499)
Halogen Free Flame Retardant Cables for Working
Voltages up to and including 450/750 Volts Specification
3
DOC.ETD 9(6507)
Areial bunched cables-for working voltages upto and
including 1 100 Volts - Specification (First revision of iS
14255)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
30
1
ETD 10 PRIMARY CELLS AND BATTERIES
SCOPE - To prepare standards for cells and batteries particularly those relating to the
specification, checking of their dimensions and characteristics and to provide
guidance on matters of safety
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 586:1976
Leclanche type dry batteries for
telecommunications,signalling and general purposes
(third revision)
Dec 2010
3
2
IS 2083:1991
Flashlights (second revision)
Dec 2010
2
3
IS 2652:1976
Schedule of terminals for leclanche type primary
batteries (first revision)
Dec 2010
2
4
* IS 6303:1984
| IEC 86-1(1972)
General requirements and methods of tests for dry
cells and batteries
Dec 2010
6
5
IS 6303(Part 4):2013
| IEC 60086-4:2007
Primary batteries – Part 4: Safety of lithium batteries
Jan 2013
6
* IS 8144:1997
| IEC 86-2(1972)
Multipurpose dry batteries (First revision)
Feb 2013
2
7
* IS 9128:1999
Heavy duty dry batteries (first revision)
Mar 2014
2
8
IS 11675:1986
| IEC 86-2(1982)
Button cells - Silver oxide
Mar 2014
9
IS 15063:2001
| IEC 86-2(1994)
Alkaline manganese dioxide cells
Aug 2011
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 10(6258)
Primary Batteries Part 1: General (Second Revision of
IS 6303)
2
DOC.ETD 10(6259)
Primary Batteries: Part 2 Physical and electrical
specification (Second Revision of IS 8144 and 9128)
3
DOC.ETD 10(6276)
Primary batteries – Part 5: Safety of batteries with
aqueous electrolyte [IEC 60086-5(2005)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
31
ETD 11 SECONDARY CELLS AND BATTERIES
SCOPE - To prepare standards for all rechargeable cells and batteries (starter
batteries, stationary batteries, traction batteries etc.)
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1145:1980
Lead-acid storage batteries for motor cycles, autorickshaws and similar vehicles (second revision)
Dec 2013
2
IS 1146:1981
Rubber and plastic containers for lead-acid storage
batteries (second revision)
Dec 2013
3
3
IS 1651:2013
Stationary cells and batteries, lead-acid type (with
tubular positive plates) - Specification (fourth
revision)(superseding IS:541)
4
IS 1652:2013
Stationary cells and batteries, lead-acid type with
plante positive plates - Specification (fourth revision)
5
IS 2512:1978
Miners cap lamp batteries (lead-acid type) (first
revision)
Dec 2013
3
6
IS 5154(Part 1):2013
/ [IEC 60254-1(2005)
Lead-acid traction batteries – Part 1: General
requirements and methods of test (Second Revision)
Jun 2013
7
IS 5154(Part 2):2013
/ [IEC 60254-2(2008)
Lead-acid traction batteries – Part 2: Dimensions of
cells and terminals and marking of polarity on cells
(Second Revision)
Jun 2013
8
IS 6071:1986
Synthetic separators for lead-acid batteries (first
revision)
Sep 2012
2
9
IS 6304:1992
Stationary batteries lead-acid type with pasted positive
plates (second revision)
Sep 2012
1
10
IS 6848:1979
| IEC 77(1968)
Lead-acid batteries for train lighting and airconditioning
services (first revision)
Dec 2013
3
11
IS 7372:1995
| IEC 95-1(1988)
Lead-acid storage batteries for motor vehicles (first
revision)
Sep 2012
3
12
IS 7624:1990
| IEC 95-1(1980)
Lead-acid starter batteries for diesel locomotives and
rail cars (first revision)
Dec 2013
13
IS 7660:1988
Lead-acid batteries for electric locomotives and
electrical multiple units (first revision)
Dec 2013
14
IS 8320:2000
General requirements and methods of test for leadacid storage batteries (second revision)
15
IS 9814:1981
Lead-acid storage batteries for marine use
Dec 2013
16
IS 10893:1984
Sealed nickel-cadmium button type rechargeable
single cell
Dec 2013
17
IS 10918:1984
| IEC 623(1978)
Vented type nickel cadmium batteries
Dec 2013
18
IS 12013:1987
Lead-acid batteries for 110 volts train lighting system
with monobloc containers
Sep 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
32
Jul 2010
2
19
IS 13300:1992
Nickel -cadmium aircraft batteries (aerobatic and nonaerobatic)
Sep 2012
20
IS 13315:1992
| IEC 623(1983)
Nickel -cadmium batteries for electric locomotives
Sep 2012
21
IS 13369:1992
Stationary lead - acid batteries (with tubular positive
plates) in monobloc containers
Sep 2012
2
22
IS 13514:2014
/ IEC 61982:2012
23
IS 13568:1992
Lead -acid light weight storage batteries for motor
cycles and similar vehicles fitted with ac circuitry
Sep 2012
1
24
IS 13595:1992
Silver-oxide-zinc batteries for aircraft
Sep 2012
25
IS 14217:1994
Miner's cap lamp batteries (alkaline type)
Dec 2013
26
IS 14218:1994
| IEC 285(1983)
Sealed cylindrical type rechargeable nickel cadmium
cells
Dec 2013
27
IS 14257:1995
| IEC 95-1(1988)
Lead-acid storage batteries for motor vehicles with
light weight and high cranking performance
Dec 2013
28
IS 14782:2000
Code of practice for maintenance and testing of large
lead- acid batteries for generating systems and
substations
May 2010
29
IS 15549:2005
Stationary valve regulated lead acid batteries Specification
Jun 2010
30
IS 15767:2008
/ IEC 62259:2003
Secondary Cells and Batteries Containing Alkaline or
other Non-Acid Electrolytes – Nickel-Cadmium
Prismatic Secondary Single Cells with Partial Gas
Recombination
Jun 2013
31
* IS 16046:2012
/ IEC 62133(2002)
Secondary cells and batteries containing alkaline or
other non-acid electrolytes – Safety requirements for
portable sealed secondary cells, and for batteries
made from them, for use in portable applications
32
IS 16047:2012
/ IEC 61960 (2011)
Secondary cells and batteries containing alkaline or
other non-acid electrolytes – Secondary lithium cells
and batteries for portable applications
33
IS 16048(Part 1):2013
/ IEC 61951-1:2006
Secondary cells and batteries containing alkaline or
other non-acid electrolytes -- Portable sealed
rechargeable single cells -- Part 1: nickel-cadmium
34
IS 16048(Part 2):2013
/ IEC 61951-2:2011
Secondary cells and batteries containing alkaline or
other non-acid electrolytes - Portable sealed
rechargeable single cells - Part 2: nickel-metal hydride
35
IS 16049:2013
/ IEC 60622:2002
Secondary cells and batteries containing alkaline or
other non-acid electrolytes – Sealed nickel-cadmium
prismatic Rechargeable single cells
36
IS 16220(Part 1):2014
/ IEC 61056-1:2012
General purpose lead-acid batteries (valve-regulated
types) - Part 1: General requirements, functional
characteristics - Methods of test
Secondary batteries (except lithium) for the propulsion
of electric road vehicles - Performance and endurance
tests (First Revision)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
33
1
1
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 11(6497)
Secondary Cells and Batteries for Solar Photovoltaic
Application ─ General Requirements and Methods of
Test
2
DOC.ETD 11(6562)
Stationary lead acid storage batteries for motor
vehicles - Valve regulated type
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 11(6722)
General purpose lead-acid batteries (valve-regulated
types) – Part 2: Dimensions, terminals and marking
(IEC 61056-2:2012 )
2
DOC.ETD 11(6723)
Portable lead-acid cells and batteries (Valve-regulated
types) Part 3: Safety recommendations for use in
electric appliances (IEC 61056-3:1991)
3
DOC.ETD 11(6724)
Secondary cells and batteries containing alkaline or
other non-acid electrolytes – Safety requirements for
portable sealed secondary cells, and for batteries
made from them, for use in portable applications (First
Revision of IS 16046) (IEC 62133:2012)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
34
ETD 12 MEASURING EQUIPEMENT FOR BASIC ELECTRICAL QUANTITIES
SCOPE - To prepare standards for direct and indirect acting analogue and digital
indicating and recording instruments and their accessories, also transducers
having electrical inputs and outputs for measuring electrical quantities by any
method on direct current and alternating current at distribution system
frequencies and their harmonics
To prepare standards for primary reference apparatus, operating on direct
current and alternating current at distribution frequencies and their
harmonics for the purpose of measurement, traceability and intercomparison
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1248(Part 1):2003
| IEC 600 51-1(1997)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 1 General
requirements (fourth revision)
Sep 2013
2
IS 1248(Part 2):2003
| IEC 600 51-2(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 2 Ammeters
and voltmeters (third revision)
Aug 2013
1
3
IS 1248(Part 3):2003
| IEC 600 51-3(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 3 Wattmeters
and varmeters (third revision)
Aug 2012
1
4
IS 1248(Part 4):2003
| IEC 600 51-4(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 4 Frequency
meters (third revision)
Aug 2013
1
5
IS 1248(Part 5):2003
| IEC 600 51-5(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 5 Phase
meters, power factor meters and synchroscope (third
revision)
Aug 2013
1
6
IS 1248(Part 6):2003
| IEC 600 51-6(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 6 Ohmmeters
(impedance meters) and conductance meters (third
revision)
Aug 2013
7
IS 1248(Part 7):2003
| IEC 600 51-7(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 7 Multifunction
instruments (third revision)
Aug 2013
1
8
IS 1248(Part 8):2003
| IEC 600 51-8(1984)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 8 Accessories
(third revision)
Sep 2013
1
9
IS 1248(Part 9):2003
| IEC 600 51-9(1988)
Direct acting indicating analogue electrical measuring
instruments and their accessories: Part 9 Test
methods (third revision)
Dec 2013
10
IS 1765:1980
| IEC 60523:1975
Direct current potentiometers (second revision)
Aug 2012
11
IS 2419:2012
| IEC 61554 : 1999
Panel Mounted Equipment — Electrical Measuring
Instrument —Dimensions For Panel Mounting (
Second Revision )
Aug 2012
1
dc moving coil galvanometers
Jan 2010
1
Insulation resistance testers, hand operated (magneto
generator type) (second revision)
Jan 2010
12
IS 2442:1963
13
* IS 2992:1987
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
35
14
IS 3602:1966
Recommendations for the design of scales and
indexes for indicating instrumentsfor scales of 1 to 2
percent resolution
Aug 2012
15
IS 3635:1966
Methods of test for resistance of metallic electrical
resistance material
Jan 2010
16
IS 3636:1966
Method of test for temperature co-efficient of precision
resistor wires
Jan 2010
Direct recording electrical measuring instruments
Jan 2010
17
IS 6236:1971
| IEC 60258(1968)
18
IS 7889:1975
Vibration galvanometers
Jan 2010
19
IS 7890:1975
Ballistic galvanometers
Jan 2010
Standard cells
Jan 2010
20
IS 7914:1975
| IEC 60428(1973)
21
IS 8143:1976
Plugs and keys for resistance boxes
Jan 2010
22
IS 8160:1976
Tangent galvanometers
Jan 2010
23
IS 8197:1976
Terminal markings for electrical measuring
instruments and their accessories
Jan 2010
24
IS 8525:1977
Recommendations for design of linear scales and
indexes for indicating instruments to be read to 0.331.25 percent resolution.
Aug 2012
25
IS 8945:1987
Electrical measuring instruments for explosive gas
atmospheres (First Revision)
Jan 2010
26
IS 9051:1979
Specification for Rheostats
Jan 2010
27
* IS 9223:1989
Portable earth resistance meters (first revision)
Jan 2010
28
IS 9249(Part 1):1979
| IEC 60414(1973)
Safety requirements for indicating and recording
electrical measuring instruments and their
accessories: Part 1 Common safety requirements for
instruments
Aug 2012
29
IS 9249(Part 2):1982
| IEC 60414((1973)
Safety requirements for indicating and recording
electrical measuring instruments and their
accessories: Part 2 Safety requirements for
instruments using a mains supply
Aug 2012
30
IS 10659:1983
| IEC 60564(1977)
Specification for Direct current bridges for measuring
resistance (superseding IS:1565)
Aug 2012
31
IS 11067:1984
Direct current standard resistors
Aug 2012
32
IS 11212:1985
Direct current resistive volt ratio boxes
Aug 2012
33
IS 11287:1985
Bridge insulation testers (Magneto generator type)
Aug 2012
34
* IS 11994:1986
Portable insulation resistance tester (mains operated)
Aug 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
36
3
1
1
35
IS 12312:1987
| IEC 60618
Inductive voltage dividers
Jan 2010
36
IS 14570:2012
/ IEC 60688:1992
Electrical measuring transducers for converting AC
electrical quantities to to analogue or digital signals
May 2012
37
IS 14571:1998
/ IEC 61028(1991)
Electrical measuring Instruments X-Y recorders.
38
IS 61557(Part 1):2007
/ IEC 61557-1(2007)
Electrical safety in low voltage distribution system up to May 2012
1000 V a.c. and 1500 V d.c. equipment for testing,
measuring or monitorin or protective measurs - Part 1:
Genral requirments IEC 61557-1 (Superseding IS
2992)
39
IS 61557(Part 2):2007
/ IEC 61557-2(2007)
Electrical safety in low voltage distribance systems UP
to 1 000 V a.c. and 1 500 V d.c. - Equipment for
testing, measuring or monitoring or protective
measures Part 2 Insulation resistance IEC 615572(Superseding IS 11994)
May 2012
40
IS 61557(Part 5):2007
/ IEC 61157-5(2007)
Electrical safety in low voltage distribution systems up
to 1000 V a.c. and 1500 V d.c. - Equipment dor testing,
measuring or monitoring or protective measures - Part
5: Resistance to earth IEC 61557-5 (Superseding IS
9223)
Apr 2012
Jul 2013
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 12(6671)
/ IEC 61010-1 (2010)
Safety requirements for electrical equipment for
measurement, control and laboratory use – Part 1 :
General requirements
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
37
2001
ETD 13 EQUIPMENT FOR ELECTRICAL ENERGY MEASUREMENT TARIFF AND
LOAD CONTROL
SCOPE - To prepare international standards for equipment for electrical energy
measurement, tariff - and load control, customer infromation, payment, local
and/or remote data exchange, using electromechanical and/or electronic,
technologies for applications ranging from electrical energy generation to
residential. The standards may include requirements and test methods to
cover mechanical, environmental, electrical, safety, metrology dependability
aspects as well as functional requirements and data models.
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
2
3
IS 1766:1998
| IEC 61038:1992
IS 7700:1975
IS 8530:1977
| IEC 60211:1966
Time swtiches for metering and load control
(second revision)
Oct 2013
Quadrature phase-shifting voltage transformers
Sep 2010
Maximum demand indicators (class 1)
Sep 2010
4
IS 9792(Part 1):2005
Guide for testing, calibration and maintenance of ac
electricity meters: Part 1Single phase whole current
watthour meters, Class 2 (first revision)
Jan 2010
5
IS 11426(Part 1):2006
Alternating current precision electricity meters for
testing purposes: Part 1 Requirements for electromechanical meters (first revision)
Apr 2011
6
IS 11448:2000
Application guide for ac electricity meters(first revision)
Jul 2010
7
IS 12346:1999
| IEC 60736:1982
Testing equipment for ac electrical energy meters
(first revision)
Jul 2009
8
** IS 13010:2002
| IEC 60521:1988
AC watt-hour meters, Class 0.5, 1 and 2(first revision)
Sep 2012
2
9
** IS 13779:1999
| IEC 61036:1996
AC static watthour meters (Class 1 and 2)
(first revision)
Oct 2009
4
10
IS 14372:1996
Volt-ampere hour meters for full power factor range
[superseding IS:722(Part 7/Sections 1, 2 and 3)-1987]
Sep 2009
11
IS 14415:1997
| IEC 60211:1996
Volt-Amphere hour meters for restricted power factor
range - specification [superseding IS:722 (Part 5):1980
Dec 2012
12
IS 14451(Part 1):1998
| IEC 60338:1970
Telemetering of consumption and demand:
Part 1 Impulse transmitting and receiving devices
Jan 2013
13
IS 14451(Part 2):1999
| IEC 60338:1970
Telemetering for Consumption and Demands Part 2
Direct digital transfer of meter values
Jul 2009
ac static transformer operated watthour and var-hour
meters, class 0.2S and .5S-Specification
Oct 2009
Nov 2011
14
** IS 14697:1999
| IEC 60687:1992
15
IS 15707:2006
Testing, evaluation, installation and maintenance of ac
electricity meters - Code of Practice
16
IS 15884:2010
Alternating current direct connected static pre-payment
meters for active energy (Class 1 & 2) - Specification
17
IS 15959:2011
Electricity Metering - Data Exchange for meter reading,
tariff and load control - Companion Specification
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
38
3
1
18
IS 62051(Part 1):2004
/ IS/IEC 62051-1:2004
Electricity Metering - Data exchange for meter reading
tariff and load control Part 1 Terms relate to data
exchange with metering equipment using
DLMS/COSEMV (IEC 62051-1:2004)
19
IS 62056(Part 21):2002
/ IS/IEC 62056-21:2002
Electricity Metering Data exchangefor meter reading,
tariff and load control- Part 21 direct local data
exchange (IEC 62056-21:2002)
20
IS 62056(Part 42):2002
/ IS/IEC 62056-42:2002
Electricity metering Data exchange for meter reading
tariff and load control -Part 42 Physical layer services
and procedures for connection-oriented asynchronous
data exchange. (IEC 62056-42:2002)
21
IS 62056(Part 46):2007
/ IS/IEC 62056-46:2007
Electricity metering Data exchange for meter reading
tariff and load control -Part 46 Data link layer using
HDLC protocol (IEC 62056-46:2007)
22
IS 62056(Part 47):2006
/ IS/IEC 62056-47:2006
Electricity Metering - Data Exchange for meter reading,
tariff and load control Part 47 COSEM transport layers
for IPv4 networks
23
IS 62056(Part 53):2006
/ IS/IEC 62056-53:2006
Electricity metering Data exchange for meter reading
tariff and load control -Part 53 COSEM application
layer'(IEC 62056-53:2006)
24
IS 62056(Part 61):2006
/ IS/IEC 62056-61:2006
Electricity metering Data exchange for meter reading
tariff and load control -Part 61 Object identification
system (OBIS) (IEC 62056-61:2006)
25
IS 62056(Part 62):2006
/ IS/IEC 62056-62:2006
Electricity metering Data exchange for meter reading
tariff and load control -Part 62 Interface Classes' (IEC
62056-62:2006)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
39
ETD 14 ELECTRICAL WIRING ACCESSORIES
SCOPE - To prepare standards for electrical wiring accessories ; such as lamp
holders, switches, plugs and socket- outlets, connecting devices and
conduits and their accessories for electrical installations
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 371:1999
Ceiling roses (third revision)
Mar 2010
4
2
IS 1258:2005
| IEC 61184(1997)
Bayonet lamp holders (fourth revision)
Jun 2010
3
3
IS 1293:2005
| IEC 60884-1 (2002)
Plugs and socket outlets of rated voltage upto and
including 250 volts and rated current upto and
including 16 amperes - Specification (third revision)
Jun 2010
5
4
IS 2412:1975
Link clips for electrical wiring (first revision)
May 2012
2
5
IS 3010(Part 1):1965
Appliance-connectors and appliance-inlets (nonreversible three-pin type): Part 1 Appliance
connectors
Apr 2014
6
6
IS 3010(Part 2):1965
Appliance-connectors and appliance-inlets(nonreversible three-pin type): Part 2 Appliance inlets
Apr 2014
5
1
7
IS 3323:1980
| IEC 60400(1972)
Bi-pin lampholders for tubular fluorescent lamps
(first revision)
Oct 2012
8
IS 3324:1982
| IEC 400(1972)
Holders for starters for tubular fluorescent lamps
(first revision)
Jun 2013
9
IS 3419:1989
10
** IS 3480:1966
11
IS 3837:1976
Fittings for rigid non-metallic conduits (second revision) May 2012
Flexible steel conduits for electrical wiring
May 2012
1
Accessories for rigid steel conduits for electrical wiring
(first revision)
May 2012
1
Jul 2012
6
12
* IS 3854:1997
| IEC 60669-1(1998)
Switches for domestic and similar purposes (second
revision)
13
IS 4160:2005
| IEC 60884-2-6 (1997)
Interlocking switch socket outlets - Speification
(first revision)
Jun 2010
14
IS 4649:1968
Adaptors for flexible steel conduits
May 2012
15
IS 6896:1973
Connectors (two-way) for railway coach wiring
May 2012
1
16
IS 6965:1979
Switches for use in railway coaching stock (first
revision)
May 2012
2
17
IS 8200:1976
Toggle switches used in traction application
Jun 2013
Conduits for electrical installations: Part 1 General
requirements
Nov 2010
18
* IS 9537(Part 1):1980
| IEC 60614-1(1978)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
40
1
19
** IS 9537(Part 2):1981
Conduits for electrical installations:Part 2 Rigid steel
conduits (superseding IS:1653)
May 2012
3
20
** IS 9537(Part 3):1983
| IEC 60614-2-2(1980)
Conduits for electrical installations: Part 3 Rigid plain
conduits of insulating materials (superseding IS:2509)
May 2012
2
21
** IS 9537(Part 4):1983
Conduits for electrical installations: Part 4 Pliable selfrecovering conduits of insulating materials
May 2012
22
* IS 9537(Part 5):2000
| IEC 60614-2-3(1990)
Conduits for a electrical installations: Part 5 Pliable
conduits of insulating material (Superseding IS 6946)
Jun 2010
23
IS 9537(Part 6):2000
| IEC 60614-2-6(1992)
Conduit for electrical installations: Part 6 Pliable
conduits of metal or composit materials
Mar 2010
24
IS 9537(Part 8):2003
Conduits for electrical instalations Part 8 Rigid non
threadable conduits of aluminium alloy
Apr 2013
25
IS 10276(Part 1):1982
| IEC 60238(1975)
Edison screw lampholders :
Part 1 Requirements and tests
Jun 2013
26
IS 10276(Part 2):1982
| IEC 60238(1975)
Edison screw lampholders :
Part 2 Standard data sheets for lamp holders and
gauges
Jun 2013
Electronic type fan regulators
Aug 2010
27
IS 11037:1984
3
28
IS 14763:2000
| IEC 60423(1993)
Conduit for electrical purposes, outside diameters of
conduits for electrical installations and threads for
conduits and fittings
Mar 2010
29
IS 14768(Part 1):2000
| IEC 61035-1(1990)
Conduit fittings for electrical installations :Part 1
General requirements
Nov 2013
30
IS 14768(Part 2):2003
| IEC 61035-2-1(1993)
Conduit fittings for electrical installations : Part 2 Metal
conduit fittings (superseding IS 2667)
Feb 2013
31
IS 14772:2000
| IEC 60670-1(1989)
Enclosures for accessories for household and similar
fixed electrical installations (Superseding IS 5133(Part
1 and 2)
May 2010
32
IS 14927(Part 1):2001
| IEC 61084-1(1991)
Cable trunking and ducting systems for electrical
installations :Part 1 General requirements
Aug 2012
33
IS 14927(Part 2):2001
| IEC 61084-2-1(1996)
Cable trunking and ducting systems for electrical
installations: Part 2 Cable trunking and ducting
systems instended for mounting on walls or ceilings
May 2012
34
IS 14930(Part 1):2001
| IEC 61386-1(1996)
Conduit systems for electrical installations :
Part 1 General requirements
May 2011
3
35
IS 14930(Part 2):2001
| IEC 61386-2(1995)
Conduit systems for electrical installations :
Part 2 Particular requirements for conduit system
buried underground
May 2011
2
36
IS 15368:2003
Cable reels for household and similar purposes
Jul 2013
37
IS 15787:2008
| IEC 60884-2-3 (1989)
Switch- socket outlets (Non-Interlock Type)
Jul 2013
38
IS 60309(Part 1):2002
/ IEC 60309-1(1999)
Plugs, socket-outlets and couplers for industrial
purposes: Part 1 General requirements (first revision)
Oct 2012
39
IS 60309(Part 2):2002
/ IEC 60309-2(1999)
Plugs, socket-outlets and couplers for industrial
purposes: Part 2 Dimensional interchangeability
requirements for pin and contact-tube accessories
(first revision)
Oct 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
41
1
40
IS 60320(Part 1):2001
/ IEC 60320-1(2001)
Appliance couplers for household and similar general
purposes Part 1 General requirements
Nov 2012
41
IS 60320(Part 2/Sec 2):1998
/ IEC 60320-2-2(1998)
Appliance couplers for household and similar general
purposes part 2-2 Interconnection couplers for
household and similar equipment
Nov 2012
42
IS 60320(Part 2/Sec 3):2007
| IEC 60320-2-3(1998)
Appliance couplers for household and similar general
purposes- part 2-3 Appliance coupler with a degree of
protection higher IPXO
Nov 2012
43
IS 61058(Part 1):2001
/ IS/IEC 61058-1(2000)
Switches for Appliances: Part 1 General Requirement
(IEC 61058-1)
Sep 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 14(6472)
Conduit Systems For Cable Management - Part 1 :
General Requirements
2
DOC.ETD 14(6473)
Conduit Systems For Cable Management - Part 21 :
Rigid Conduit Systems
3
DOC.ETD 14(6474)
Conduit Systems For Cable Management - Part 22 :
Pliable Conduit Systems
4
DOC.ETD 14(6475)
Conduit Systems For Cable Management - Part 23 :
Flexible Conduit Systems
5
DOC.ETD 14(6476)
Conduit systems for cable management - Part 24
particular requirements conduit systems buried under
ground
6
DOC.ETD 14(6485)
Cable management — Cable tray systems and cable
ladder systems [IEC 61537 (2006)]
7
DOC.ETD 14(6486)
Cable cleats for electrical installations [IEC 61914
(2009)]
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 14(6663)
Switches for household and similar fixed electrical
installations – Part 2-1: Particular requirements –
Electronic switches [IEC 60669-2-1 (2009)]
2
DOC.ETD 14(6664)
SPlugs and socket-outlets for household and similar
purposes – Part 2-5: Particular requirements for
adaptors [IEC 60884-2-5(1995)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
42
ETD 15 ROTATING MACHINERY
SCOPE - To prepare standards on rotating electrical machines like induction,
synchronous, motors, generators, dc machines and turbines including
carbon brushes for electrical machines (with the exception of traction
machines and rotating machinery coming under the purview of other
Committees)
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 325:1996
| IEC 60034-1(1983)
Three-phase induction motors(first revision)
Jan 2012
3
2
IS 900:1992
Code of practice for installation and maintenance of
induction motors (Second revision)
Feb 2013
3
IS 996:2009
Specification for single phase ac induction motors for
general purpose (third revision)
Feb 2014
1
4
IS 1231:1974
| IEC 60072 (1971)
Dimensions of three-phase foot-mounted induction
motors (third revision)
Feb 2013
4
5
IS 2223:1983
| IEC 60072 (1971)
Dimensions of flange mounted ac induction motors
(first revision)
Jan 2012
2
6
IS 2253:1974
| IEC 34-7(1972)
Designation for types of construction and mounting
arrangement of rotating electrical machines (first
revision)
Jan 2012
7
IS 2254:1985
Dimensions of vertical shaft motors for pumps (second
revision)
Jan 2012
8
IS 2968:1964
Dimensions of slide rails for electric motors
Jan 2012
1
9
IS 2972(Part 1):1979
Textile motors: Part 1 Loom motors (first revision)
Jan 2012
2
10
IS 2972(Part 2):1979
Textile motors: Part 2 Card motors (first revision)
Jan 2012
1
11
IS 2972(Part 3):1979
Textile motors: Part 3 Spinning frame motors (first
revision)
Jan 2012
12
IS 3682:1966
Flameproof ac motors for use in mines
Jan 2012
1
13
IS 4029:2010
Guide for testing three-phase induction motors (First
Revision)
14
IS 4665(Part 1):1984
Portable electric motor-operated tools: Part 1 General
requirements and tests (first revision)
Jan 2012
1
15
IS 4665(Part 2):1984
Portable electric motor-operated tools:Part 2 Specific
requirements for tools
Jan 2012
16
IS 4758:1968
Method of measurement of noise emitted by machines
Jan 2012
17
IS 4889:1968
| IEC 2 D
Method of determination of efficiency of rotating
electrical machines
Jan 2012
18
* IS 5422:1996
| IEC 60034-3(1988)
Turbine type generators (first revision)
Jan 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
43
3
19
IS 6362:1995
/ IEC 60034-6:1991
Designation of methods of cooling of rotating electrical
machines
Jan 2012
20
IS 7132:1973
| IEC 60034-1(1969)
Guide for testing synchronous machines
Jan 2012
21
* IS 7306:1974
| IEC 60034-4(1967)
Methods for determining synchronous machine
quantities from tests
Jan 2012
22
IS 7538:1996
Three-phase squirrel cage induction motors for
centrifugal pumps for agricultural applications (first
revision)
Jan 2012
23
IS 7572:1974
Guide for testing single-phase ac and universal motors
Jan 2012
24
IS 7816:1975
Guide for testing insulation resistance of rotating
machines
Jan 2012
2
25
IS 8151:1976
Single-speed three-phase induction motors for driving
lifts
Jan 2012
2
Dimensions and output series for rotating electrical
machines (first revision)
Apr 2014
Jan 2012
1
26
IS 8223:1999
| IEC 60072-2(1990)
2
27
IS 8789:1996
Values of performance characteristics for three-phase
induction motors (first revision)
28
IS 9283:2013
Motors for Submersible Pumpsets - Specification
(second revision)
29
IS 9320:1979
Guide for testing of direct current (dc) machines
Jan 2012
1
30
IS 9582(Part 1):1980
Single-phase electric motors for definite purposes:
Part 1 Domestic laundry machine motors
Mar 2014
1
31
IS 9628:1980
Three-phase induction motors with type of protection 'n' Mar 2014
32
IS 9670:1980
Direct current micro motors for cassette tape recorders
and other applications
Mar 2014
33
IS 9919:1999
Guide for selection and use of carbon brushes for
applications in rotating electrical machines
Feb 2013
34
IS 10534:1983
Method of measurement of airborne noise emitted by
gas turbine installations
Jan 2012
35
IS 11537:1985
Centrifugal switch for single phase induction motors
Jan 2012
36
* IS 12065:1987
| IEC 60034-9
Permissible limits of noise level for rotating electrical
machines
Mar 2014
37
IS 12066:1987
Three-phase induction motors for machine tools
Mar 2014
38
* IS 12075:2008
Mechanical vibration of rotating electrical machines
with shaft heights 56 mm and higher-measurement,
evaluation and limits of vibration severity (first revision)
39
IS 12615:2011
Energy Efficient Three Phase Squirrel Cage Induction
Motors (Second Revision)
40
IS 12642:1989
| IEC 60778
Brush-holders for slip rings group R-Type RA
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
44
Jul 2013
Mar 2014
1
41
IS 12998(Part 1):1991
/ ISO 1680-1:1986
Method f measurement of airborne noise emitted by
rotating machinery: Part 1 Engineering method for free
field conditions over a reflecting plane
Feb 2013
42
IS 12998(Part 2):1991
/ ISO 1680-2:1986
Method of measurement of airborne noise emitted by
rotating machinery: Part 2 Survey method
Feb 2013
Stepping Motors
Jan 2012
43
IS 13079:1991
44
IS 13107:1991
/ IEC 60279(1969)
Guide for measurement of winding resistance of an ac
machine during operation at alternating voltage
Feb 2013
45
IS 13364(Part 1):1992
| IEC 60034-1
Specification for ac generators driven by reciprocating
internal combustion engine: Part 1 Rated up to 20 kVA
Feb 2013
46
IS 13364(Part 2):1992
| IEC 60341(1983)
Specification for ac generators driven by reciprocating
internal combustion engine: Part 2 Rated above 20
kVA and upto 1250 kVA
Feb 2013
47
IS 13466:1992
| IEC 60136, 467, 773
Specification for brushes for electrical machines
[superseding IS:3003 (Parts 3 and 4)-1977]
Feb 2013
Flexible conductors for carbon brushes
Feb 2013
Guide on effects of unbalanced voltages on the
performance of three-phase cage induction motors
Feb 2013
48
49
IS 13525:1992
* IS 13529:1992
| IEC 600892(1987)
50
IS 13555:1993
Guide for selection and application of three-phase ac
Mar 2014
induction motors for different types of driven equipment
51
IS 13584:1993
| IEC 413(1972)
Specification for brush materials for electrical
machinery [Superseding IS 3003(Part 2):1977]
Mar 2014
52
IS 13586:1993
| IEC 276(1968)
Definitions and nomenclature for carbon brushes,
brush holders, commutators and slip rings for rotating
electrical machinery (superseding IS:3003(Part 1)1977)
Mar 2014
53
IS 13937(Part 1):1994
/ ISO 7574-1:1985
Statistical method of determining and verifying
standard noise emission values of machinery and
equipment: Part 1 General conditions and definitions
Jan 2012
54
IS 13937(Part 2):1994
/ ISO 7574-2:1985
Statistical method of determining and verifying
standard noise emission values of machinery and
equipment: Part 2 Methods of stated values for
individual machines
Jan 2012
55
IS 13937(Part 3):1994
/ ISO 7574-3:1985
Statistical method of determining and verifying
standard noise emission values of machinery and
equipment: Part 3 Simple (transition) method for stated
values for batches of machines
Jan 2012
56
IS 13937(Part 4):1994
/ ISO 7574-1985
Statistical method of determining and verifying
standard noise emission values of machinery and
equipment: Part 4 Methods for stated values for
batches of machines
Jan 2012
57
IS 14195:1994
/ IEC 61015(1990)
Brush-holders for electrical machines guide to the
measurement of the static thrust applied to brush
Jan 2012
58
IS 14196:1994
/ IEC 60560(1977)
Definitions and terminology of brush-holders for
electrical machines
Jan 2012
59
IS 14197:1994
/ IEC 60193:1965
Code for model acceptance tests of hydraulic turbines
Jan 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
45
1
60
IS 14198(Part 1):1994
/ IEC 60953-1:1990
Rules for steam turbines thermal acceptance tests Method A
Jan 2012
61
IS 14198(Part 2):1994
/ IEC 60953-2:1990
Rules for steam turbines thermal acceptance tests Method B
Jan 2012
62
IS 14205(Part 1):1994
/ IEC 60045-1:1991
Steam turbines Part 1 Specification
Jan 2012
63
IS 14222:1995
/ IEC 60034-15:1990
Impulse withstand levels of rotating ac machines with
form wound stator coils
Jan 2012
64
IS 14376:1996
| IEC 136(1986)
Brush holders for electrical machines
Jan 2012
65
IS 14377:1996
Induction motors for fan used in air-conditioning and
ventilation
Jan 2012
Dimensions and output series for rotating electrical
machines Part 2 Frame numbers 355 to 1000 and
flange numbers 1180 to 2360
Jul 2013
66
IS 14568(Part 2):1998
/ IEC 60072-2(1990)
67
IS 14569:1999
Commutators for electrical machines
Feb 2014
68
IS 14578:1999
Three-phase induction motors for use in nuclear power
plants
Mar 2014
1
69
IS 14582:1998
Single-phase small a.c. electric motors for centrifugal
pumps for agricultural applications
Mar 2013
1
70
IS 14889:2000
Copper tamping powder for carbon brushes
Dec 2010
71
IS 15429:2004
Storage, installation and maintenance of DC motors Code of practice
Jun 2009
72
IS 15664:2006
/ ISO 2314(1989)
Gas turbines - Acceptance tests
Apr 2011
73
IS 15665:2006
/ ISO 11086(1996)
Gas turbines - Vocabulary
Apr 2011
74
IS 15666(Part 1):2006
/ ISO 3977-1(1997)
Gas turbines - Procurement - Part 1: General
introduction and definitions
Apr 2011
75
IS 15666(Part 2):2006
/ ISO 3977-2(1997)
Gas turbines - Procurement - Part 2: Standard
reference conditions and ratings
Apr 2011
76
IS 15666(Part 3):2006
/ ISO 3977-3(2004)
Gas turbines - Procurement - Part 3: Design
requirements
Apr 2011
77
IS 15666(Part 4):2006
/ ISO 3977-4(2002)
Gas turbines - Procurement - Part 4: Fuels and
environment
Apr 2011
78
IS 15666(Part 5):2006
/ ISO 3977-5(2001)
Gas turbines - Procurement - Part 5: Applications for
petroleum and natural gas industries
Apr 2011
79
IS 15666(Part 7):2006
/ ISO 3977-5(2002)
Gas turbines - Procurement - Part 7: Technical
information
Apr 2011
80
IS 15666(Part 8):2006
/ ISO 3977-8(2002)
Gas turbines - Procurement - Part 8: Inspection,
testing, installation and commissioning
Apr 2011
81
IS 15666(Part 9):2006
/ ISO 3977-9(1999)
Gas turbines - Procurement - Part 9: Reliability,
availability, maintainability and safety
Apr 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
46
82
IS 15667:2006
/ ISO 19860(2005)
Gas turbines - Data acquisition and trend monitoring
system requirements for gas turbine installations
83
IS 15880:2009
Three phase cage induction motors when fed from
IGBT converters - Application Guide
84
IS 15881:2009
Three phase cage induction motors specifically
designed for IGBT converter supply
85
IS 15999(Part 2/Sec 1):2011
Rotating Electrical Machines Part 2 Method of Tests
Section 1 Standard Methods for Determining Losses
and Efficiency from Tests (Excluding Machines for
Traction Vehicles)
Apr 2011
86
IS 60034(Part 1):2004
/ IS/IEC 60034-1(2004)
Rotating electrical machines - Part 1 Rating and
performance
Oct 2012
87
IS 60034(Part 5):2000
/ IS/IEC 60034-5(2000)
Rotating electrical machines - Part 5: Degrees of
protection provided by the integral design of rotating
electrical machines (IP code) - Classification
(Superseding IS 4691)
May 2013
88
IS 60034(Part 8):2002
/ IS/IEC 60034-8(2002)
Rotating electrical machines - Part 8: Terminal
markings and direction of rotation (Superseding IS
4728)
Aug 2013
89
IS 60041:2000
/ IS/IEC 60041(2000)
Field acceptance tests to determine the hydraulic
performance of turbines, storage pumps and pump
turbines
Jun 2010
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 15(6489)
Rotating electrical machines – Part 3: Specific
requirements for synchronous generators driven by
steam turbines or combustion gas turbines (Second
Revision of IS 5422) [IEC 60034-3(2007)]
2
DOC.ETD 15(6490)
Rotating electrical machines – Part 4: Methods for
determining synchronous machine quantities from
tests (First Revision of IS 7306) [IEC 60034-4(2008)]
3
DOC.ETD 15(6491)
Rotating electrical machines – Part 9: Noise limits
(First Revision of IS 12065) [IEC 60034-9(2007)]
4
DOC.ETD 15(6492)
Rotating electrical machines – Part 14: Mechanical
vibration of certain machines with shaft heights 56 mm
and higher – Measurement, evaluation and limits of
vibration severity (Second Revision of IS 12-75) [IEC
60034-14(2007)]
5
DOC.ETD 15(6493)
Rotating electrical machines – Part 15: Impulse
voltage withstand levels of form-wound stator coils for
rotating a.c. machines (First Revision of IS 14222)
[IEC 60034-15(2009)]
6
DOC.ETD 15(6494)
Rotating electrical machines – Part 26: Effects of
unbalanced voltages on the performance of threephase cage induction motors (First Revision of IS
13529) [IEC 60034-26(2006)]
7
DOC.ETD 15(6517)
Rotating electrical machines – Part 1: Rating and
performance (First Revision of IS/IEC 60034-1) (IEC
60034-1:2010)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
47
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 15(6518)
Acoustics – Test code for the measurement of
airborne noise emitte4d by rotating electrical
machines performance [First Revision of IS 12998
(Part 1 & 2)] (ISO 1680:1999)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 15(6501)
Rotating Electrical Machines: Specification for
Terminal Boxes for 3 Phase Rotating Electrical
Machines
2
DOC.ETD 15(6506)
Electric Traction Lifts Part 10 Poly Phase Electric
Motors for Driving Electric Traction Lifts
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
48
ETD 16 TRANSFORMERS
SCOPE - To prepare standards on power and distribution transformers, reactors, onload tap changers, etc, without limitation on voltage or power. Transformer
accessories and voltage stablizers, testing transformers and furnace
transformers are included.
(Instrument transformers, welding transformers and traction transformers
are excluded)
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
* IS 1180(Part 1):1989
Outdoor type three-phase distribution transformers
upto and including 100 kVA 11 kV:Part 1 Non-sealed
type (third revision)
Jul 2013
2
* IS 1180(Part 2):1989
Outdoor type three-phase distribution transformers
upto and including 100 kVA 11 kV:Part 2 Sealed type
(first revision)
Jul 2013
3
* IS 2026(Part 1):2011
| IEC 60076-1(2000)
Power transformers: Part 1 General (first revision)
Jul 2011
4
IS 2026(Part 2):2010
| IEC 60076-2(1993)
Power Transformers - Part 2 Temperature rise (first
revision)
5
IS 2026(Part 3):2009
/ IEC 60076-3 (2000)
Power Transformers - Part 3 Insulaiton levels,
dielectric tests and external clearances in air (third
revision)
6
IS 2026(Part 4):1977
| IEC 60076(1977)
Power transformers: Part 4 Terminal marking,tappings
and connections (first revision)
7
IS 2026(Part 5):2011
| IEC 60076-5(2006)
Power Transformers - Part 5 Ability to withstand short
circuit (first revision)
8
IS 2026(Part 7):2009
/ IEC 60076-7(2005)
Power Transformers - Part 7 Loading guide for oil
immersed power transformers
9
IS 2026(Part 8):2009
/ IEC 60076-8(1997)
Power Transformers - Part 8 Application guide
Mar 2014
10
IS 2026(Part 10):2009
/ IS/IEC60076-10(2001)
Power Transformers - Part 10 Determination of sound
levels
Mar 2014
11
12
IS 2772:1982
IS 3151:1982
| IEC 60289(1968)
Jul 2011
Non-flameproof mining transformers for use below
ground (first revision)
Jul 2011
Earthing transformers (first revision)
Jul 2011
13
IS 3639:1966
Fittings and accessories for power transformers
Jul 2011
14
IS 5142:1969
Continuously variable voltage auto transformers
Jul 2011
15
IS 5553(Part 1):1989
| IEC 60289(1988)
Reactors: Part 1 General
Jul 2013
16
IS 5553(Part 2):1990
| IEC 60 289(1988)
Reactors: Part 2 Shunt reactors
Jul 2013
17
IS 5553(Part 3):1990
| IEC 60289(1988)
Reactors: Part 3 Current limiting reactors and neutral
earthing reactors
Jul 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
49
1
2
2
18
IS 5553(Part 4):1990
| IEC 60289(1988)
Reactors: Part 4 Damping reactors
Nov 2009
19
IS 5553(Part 5):1989
| IEC 60289(1988)
Reactors: Part 5 Tuning reactors
Nov 2009
20
IS 5553(Part 6):1991
| IEC 60289(1988)
Reactors: Part 6 Earthing transformers (Neutral
couplers)
21
IS 5553(Part 7):1990
| IEC 60289(1988)
Reactors: Part 7 Arc supression reactors
Nov 2009
22
IS 5553(Part 8):1990
| IEC 60289(1988)
Reactors: Part 8 Smoothing reactors
Nov 2009
Jul 2011
23
IS 8447:1989
Manually operated voltage regulators for domestic use
(first revision)
Jul 2013
1
24
IS 8448:1989
Automatic line voltage correctors (step type for
domestic use) (first revision)
Jul 2013
2
25
IS 8468:1977
On-load tap changers
Jul 2011
1
26
IS 8478:1977
Application guide for on-load tap changers
Jul 2011
27
IS 9147:1979
Cable sealing boxes for oil immersed transformers
suitable for paper insulated lead sheathed cables for
highest system voltages from 12 kV upto and
including 36 kV
Jul 2011
28
IS 9815(Part 1):1994
Servo-motor operated automatic line voltage
correctors: Part 1 Correctors for single phase
applications (second revision)
Nov 2009
29
IS 10028(Part 1):1985
Code of practice for selection, installation and
maintenance of transformers: Part 1 Selection
Jul 2011
30
IS 10028(Part 2):1981
Code of practice for selection, installation and
maintenance of transformers; Part 2 Installation
(superseding IS:1886)
Jul 2011
31
IS 10028(Part 3):1981
Code of practice for selection, installation and
maintenance of transformers: Part 3 Maintenance
(superseding IS:1886)
Jul 2013
32
IS 10161:1982
Moving coil voltage regulators
Jul 2011
33
IS 10561:1983
| IEC 606 (1978)
Application guide for power transformers
Jul 2011
34
IS 11171:1985
| IEC 60726(1982)
Dry type power transformers
Jul 2011
35
IS 11333:1985
Flameproof dry type transformers for use in mines
Jul 2011
36
IS 12977:1990
Arc furnance transformers
Nov 2009
37
IS 13956:1994
Testing transformers
Nov 2009
38
IS 13964:1994
| IEC 551 (1976)
Methods of measurement of transformer and reactor
sound levels
Nov 2009
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
50
1
39
IS 61558(Part 1):1997
/ IS/IEC 61558-1(1997)
Safety of power Transformer,power supply units and
similar: Part 1 General requirement and test
Jul 2013
40
IS 61558(Part 2/Sec 6):1997
/ IS/IEC 61558-2-6(97)
Safety of power Transformers, power supply units and
similar: Part 2 particular requirements, Section 6
Safety Isolating transformers for general use
Jul 2013
41
IS 61558(Part 2/Sec 7):2007
/ IS/IEC 61558-2-7(07)
Safety of power Transformers, power supply units and
similar part 2-7: Particulars requirements for
transformers for toys
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 16(6686)
Outdoor type oil immersed distribution transformers
upto and including 2500 Kva, 33Kv – Specification :
Part 1 Mineral oil immersed [Fourth Revision of IS
1180(Part 1)]
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 16(6636)
Power Transformers - Part 1 General [second revision
of IS 2026 (Part 1)] ) [IEC 60076-1:2011]
2
DOC.ETD 16(6637)
Power Transformers - Part 6: Reactors [IEC 600766:2007]
DRAFT STANDARDS FORMULATED
1
DOC.ETD 16(6665)
Specification for Dry Type Power Transformers (First
Revision of IS 11171)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
51
ETD 18 INDUSTRIAL PROCESS MEASUREMENT AND CONTROL
SCOPE - To prepare standards for systems and elements used for industrial process
measurement and control concerning continuous and batch processes
To coordinate the standardization of those features of related elements
which affect suitability for integration into such systems operating with
electrical, pneumatic, hydraulics mechanical or other systems of
measurements and/or control
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 2053:1974
Thermocouple pyrometers (first revision)
Sep 2013
2
* IS 2054:1962
Reference tables for nickel/chromium-nickel/aluminium
thermocouples
Sep 2010
2
3
* IS 2055:1962
Reference tables for platinum/rhodium-platinum
thermocouples
Sep 2010
2
4
* IS 2056:1962
Reference tables for copper-constant thermocouples
Sep 2010
2
5
* IS 2057:1962
Reference tables for iron-constant thermocouples
Sep 2010
2
6
IS 2711:1979
Direct reading pH meters (second revision)
Sep 2013
1
7
IS 2806:1992
Guide to electrical resistance thermometry (first
revision)
Apr 2013
8
IS 2848:1986
Industrial platinum resistance thermometer sensors
(first revision)
May 2011
9
IS 3624:1987
Pressure and vacuum gauges (second revision)
Apr 2013
10
IS 3944:1982
Methods for determination of flowtime by use of flow
cups (first revision)
Sep 2010
11
IS 4309:1979
Method of measurement on direct reading pH meters
(first revision)
Sep 2013
12
IS 5883:1970
Nickel resistance thermometer elements
Sep 2013
13
* IS 6720:1972
Reference tables for plantinum/30 percent rhodiumplatinum/6 percent rhodium thermocouples
Sep 2013
14
IS 6804:1972
Glass electrodes for direct reading pH meters
Sep 2013
15
IS 7358:1984
Thermocouples (first revision)
Sep 2010
16
IS 7722:1975
Analogue pneumatic signals for process control
systems
Sep 2013
17
IS 7728:1984
Analogue dc current signals for process control
systems (first revision)
Sep 2010
18
* IS 7988:1976
Reference tables for chromel-kopel thermocouples
Sep 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
52
19
IS 8018:1976
Platinum and platinum alloy wires for thermocouple
elements
Sep 2013
20
IS 8457:1977
Tyre pressure gauges for automobiles (Pocket type)
Sep 2013
21
IS 8493:1977
Analogue dc voltage signals for industrial process
measurements and control systems
Sep 2010
22
IS 8495(Part 1):1977
Ceramic components for thermocouples and
resistance thermometers: Part 1 Terminal blocks
Sep 2013
23
IS 8784:1987
Thermocouple compensating cable (second revision)
Apr 2013
24
IS 8824(Part 1):1978
Electrical moisture meters: Part 1 For foodgrains
Sep 2013
25
IS 8824(Part 2):1988
Electrical moisture meters: Part 2 For jute (conductivity
type)
Sep 2010
26
IS 8935:1985
Electric solenoid operated actuators (first revision)
Sep 2010
27
IS 8992:1978
| IEC 60396(1972)
Test methods for induction furnaces
with submerged channels
Mar 2011
28
IS 9021:1978
| IEC 60398(1972)
General test conditions for industrial
electro-heating equipment
Mar 2011
29
IS 9029:1978
| IEC 60397(1972)
Methods of tests for batch furnaces with
metallic heating resistors
Mar 2011
30
** IS 9050:1979
| IEC 60239(1967)
Nominal dimensions of cylindrical machines
graphite electrodes with threaded sockets and
connecting pins for use in electric arc furnaces.
Mar 2011
Safety requirements in electro-heat installations:
Part 1 General requirements
Mar 2011
31
IS 9080(Part 1):1979
32
** IS 9080(Part 2/Sec 1):1979
| IEC 60519-2(1975)
Safety requirements in electro-heat installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 1 Protection in direct
resistance heating installations
Mar 2011
33
** IS 9080(Part 2/Sec 2):1980
Safety requirements in electro-heat installations:
Part 2 Particular requirements
for resistance heating equipment ,
Section 2 Protection in indirect
resistance heating installations
Mar 2011
34
** IS 9080(Part 2/Sec 3):1981
| IEC 60519-2(1975)
Safety requirements in electro-heat installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 3 Protection in potassium and
sodium nitrate and nitrite bath furnaces
Mar 2011
35
** IS 9080(Part 2/Sec 4):1981
| IEC 60519-2(1975)
Safety requirements in electro-heat installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 4 Protection in installations used for
drying varnishes and other similar products
Mar 2011
36
** IS 9080(Part 4):1981
| IEC 60519-4(1977)
Safety requirements in electro-heat installations:
Part 4 Particular requirements for arc furnace
installations.
Mar 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
53
1
1
37
IS 9319:1979
Electronic self-balancing potentiometric indicators and
recorders
Sep 2013
38
IS 9334:1986
Electric motor operated actuators (first revision)
May 2011
39
IS 9347:1979
Charts for recording instruments
May 2011
40
IS 9463:1980
Electronic self-balancing bridge indicators and
recorders
Sep 2013
General requirements for electric
infra-red emitters for heating purposes.
Mar 2011
Methods of tests for crucible induction furnaces
Mar 2011
Electronic speed limiters for diesel vehicles
Sep 2013
41
IS 10098:1982
| IEC 60240(1967)
42
** IS 10122:1982
| IEC 60545(1979)
43
IS 10144:1982
44
* IS 10189(Part 1):1982
Industrial process control valves: Part 1 General
requirements and tests
Sep 2013
45
* IS 10189(Part 2/Sec 1):1993
| IEC 60534-2-1(1978)
Industrial process control valves: Part 2 Flow capacity,
Section 1 Sizing equations for incompressible fluid flow
under installed conditions
Sep 2013
46
** IS 10189(Part 2/Sec 2):1993
| IEC60534-2-2(1980)
Industrial process control valves: Part 2 Flow capacity
SectIon 2 Sizing equations for compressible fluid flow
under installed conditions
Sep 2013
47
IS 10189(Part 2/Sec 1):2000
/ IEC 60534-2-1:1998
48
** IS 10215:1982
| IEC 60683(1980)
49
IS 10398:1982
50
* IS 10625:1983
51
Industrial process control valves Part2/Sec 1 Flow
Sep 2013
Capacity-sizing Equations for fluid flow under Installed
conditions (superseding of IS 10189(Part 2/Sec 1):1992
Methods of tests for submerged arc furnaces
Mar 2011
Zener barrier for intrinsically safe process control
instruments
May 2011
Reference tables for nickel/chromium-copper/nickel
(chromel-constantan) thermocouples
Sep 2010
IS 10639:1983
Disappearing filament type optical pyrometers
May 2011
52
IS 11222:1985
Dials, scales and indexes for indicating analogue
measuring instruments
Sep 2010
53
IS 11692:1986
| IEC 27(CO)60
Method of tests for electro-slag remelting furnaces
Feb 2013
54
IS 11712:1986
| IEC 27(CO)1959
Safety requirements for
electro-slag remelting furnaces.
Feb 2013
Reference tables for nickel-chromium-silicon
(Nicrosil/Nisil) Type N Thermocouples
Sep 2013
55
** IS 12051:1987
56
IS 12188:1987
Electric direct-arc melting furnaces
Feb 2013
57
IS 12434:1988
Coating/plating thickness tester, destructive type
Sep 2013
58
IS 12554(Part 1):1988
Non-destructive coating thickness testing instruments:
Part 1 Eddy current instruments
Sep 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
54
1
59
IS 12554(Part 2):1999
Non-destructive coating thickness testing instruments:
Part 2 Magnetic instruments
Sep 2013
60
IS 12555:1988
Signal conditioning devices for process control systems Sep 2013
61
IS 12556:1988
Binary direct voltage signals for process measurement
and control systems
Sep 2013
62
IS 12579:1988
Base-metal mineral insulated thermocouple cables
and thermocouples
Sep 2013
63
IS 13122(Part 1):1993
Transmitters for use in industrial process control
systems: Part 1 Methods for evaluating the
performance
May 2011
64
IS 13122(Part 2):1991
Transmitters for use in industrial process control
systems: Part 2 Guidance, installation, inspection and
routine testing
May 2011
65
IS 13211:1991
Vapour pressure dial-type thermometers
May 2011
66
IS 13263:1992
| IEC 60680(1980)
Methods of test for plasma equipment for
electroheat installations.
Sep 2013
67
IS 13673(Part 1):1993
Expression of performance of elctro chemical
analyzers :Part 1 General
Sep 2013
68
IS 13673(Part 2):1993
Expression of performance of electrochemical
analyzers :Part 2 pH values
Sep 2013
69
IS 13673(Part 3):1993
Expression of performance of electrochemical
analyzers: Part 3 Electrolytic conductivity
Sep 2013
70
IS 13673(Part 4):1998
Expression of performance of electrochemical
analyzers :Part 4 Standard for measuring oxygen
dissolved in water
Dec 2013
71
IS 13673(Part 5):1999
Expression of performance of electrochemical
analyzers :Part 5 Oxidation reduction potential or
retard potential
Feb 2014
72
IS 14254(Part 1):2003
/ IEC 61131-1(2003)
Programmable controller: Part 1 General information
(first revision)
Mar 2011
73
IS 14254(Part 2):2003
/ IEC 61131-2(2003)
Programmable Controllers: Part 2 Equipment
Requirements and Tests (first revision)
May 2011
74
* IS 60519(Part 1):1984
/ IEC 60519-1:1984
Safety in electro-heat installations:
Part 1General requirements
[Superseding IS 9080 ( Part 1)].
Nov 2010
75
IS 60519(Part 3):1988
/ IEC 60519-3:1988
Safety in electroheat installations:
Part 3 Particular requirements for induction
and
conduction heating and induction melting
installations
[Superseding IS 9080 (Part 3 )].
Nov 2010
76
IS 60519(Part 5):1980
/ IEC 60519-5:1980
Safety in electroheat installation :
Part 5 Plasma installations
Nov 2010
77
* IS 60519(Part 9):1987
/ IEC 60519-9:1980
Safety in electroheat installations:
Part 9 Particular requirements for high frequency
dielectric heating installations
Nov 2010
78
IS 61308:1994
/ IEC 61308:1994
High frequency dielectric heating installations -Test
methods for the determination of power output.
Nov 2010
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
55
1
79
IS 61508(Part 0):2000
/ (IEC 61508-0:2005)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 0: Functional
Safety
Nov 2013
80
IS 61508(Part 1):1998
/ IEC 61508-1:2000
Functional safety of
electrical/electronic/progrtammable elctronic safety related system - Part 1 General requirement
Oct 2013
81
IS 61508(Part 2):2000
/ (IEC 61508-2:2000)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 2 requirement
for electrical/Electronic/programmable electronic
safety - related systems
Oct 2013
82
IS 61508(Part 3):1998
/ (IEC 61508-3:1998)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 3 software
requirements
Dec 2013
83
IS 61508(Part 4):1998
/ (IEC 61508-4:1998)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 4 Definitions
and abbreviations
Dec 2013
84
IS 61508(Part 5):1998
/ (IEC 61508-5:1998)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 5 Examples of
Methods for the determinations of safety integrity levels
Oct 2013
85
IS 61508(Part 6):2000
/ (IEC 61508-6:2000)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 6 Guidelines
on the applications
Dec 2013
86
IS 61508(Part 7):2000
/ IEC 61508-7:2000)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 7 Over view of
techniques and measures
Jan 2014
87
IS 61511(Part 1):2003
/ (IEC 61511-1:2003)
Functional safety of electrical/electronic/programmable
electronic safety - related system - Part 1 Framework,
definitions,System, hardware and software
requirements
Jan 2014
88
IS 61511(Part 2):2003
/ IEC 61511-2:2003
Functional safety - safety instrumented systems for the
process industry sector Part 2 Guidelines for the
Applications
Oct 2013
89
IS 61511(Part 3):2003
/ IEC 61511-3:2003
Functional safety - safety instrumented systems for the
process industry sector - Part 3 Guidance for the
determination of the required safety integrity levels
Oct 2013
90
IS 62264(Part 1):2003
/ IEC 62264-1:2003
Enterprise control system Integration Part 1 Models
and Terminology
91
IS 62264(Part 2):2004
/ IEC 62264-2:2004
Enterprise control system Integration Part 2 Objects
Models Attributes
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
56
Jul 2013
ETD 19 HIGH VOLTAGE ENGINEERING
SCOPE - To prepare standards for high voltage testing techniques and for different
types of tests belonging there to such as high voltage ac, dc and impulse
tests and high current impulse tests, definitions and basic principles of
insulation coordination and insulation levels
To prepare appllication guides recommending the insulation levels in relation
to possibilities of over-voltage protection devices. The work also includes
formulation of standards for clearances and creepage distances
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1876:2005
/ IEC 60052:2002
Voltage measurement by means of standard air
gaps(first revision)
Oct 2010
2
* IS 2071(Part 3):1976
Methods of high voltage testing: Part 3 Measuring
devices (first revision)
Mar 2011
3
IS 2071(Part 1):2014
/ IEC 60060-1: 2010
High-voltage test techniques - Part 1: General
definitions and test requirements (Third Revision).
4
** IS 2165(Part 1):1977
| IEC 60071-1:1976
Insulation coordination:
Part 1 Phase to earth insulation coordination
principles and rules (second revision)
Mar 2011
5
** IS 2165(Part 2):1983
| IEC 60071-3:1982
Insulation coordination: Part 2 Phase to phase
insulation coordination principles and rules
Mar 2011
6
* IS 3716:1978
| IEC 60071-2:1976
Application guide for insulation coordination (first
revision)
Mar 2011
7
* IS 8690:1977
Application guide for measuring
devices for high voltage testing
Mar 2011
8
IS 15382(Part 1):2003
/ IEC 60664-1(2002)
Insulation coordination for equipment within low
Sep 2013
voltage system: Part 1 Principles requirements and test
9
IS 15382(Part 2/Sec 1):2003
/ IEC 60664-2-1(1977)
Insulation coordination for equipment within low
voltage system : Part 2 Appication guide, Section 1
Dimensioning procedure worksheets and dimensioning
examples
Sep 2013
10
IS 15382(Part 3):2006
/ IEC 60664-3(2003)
Insulation coordination for equipment within low
voltage system: Part 3 Use of coatings, potting or
moulding for protection against pollution
Aug 2011
11
IS 15382(Part 4):2014
12
IS 15638(Part 1):2006
/ IEC 61083-1(2001)
Instruments and software used for measurement in
high voltage impluse tests: Part 1 Requirements for
instruments( Superseeding IS 11349)
Feb 2011
13
IS 15638(Part 2):2006
/ IEC 61083-2(1996)
Instruments and software used for measurements in
high voltage impulse tests: Part 2 Evaluation of
software used for the determination of the parameters
of impulse waveforms (Superseeding IS 11349)
Feb 2011
14
IS 60060(Part 2):2010
/ IS/IEC 60060-2:2010
High voltage test techniques - Part 2 Measuring
systems (IEC 60060-2:2010)
Oct 2012
15
IS 60060(Part 3):2006
Insulation coordination for equipment within low
voltage system: Part 4 Consideration of high frequency
voltage stress [First Revision]
High Voltage test-techniques Part 3: Definitions and
requirement for on-site testing (IEC 60060-3)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
57
1
2
16
IS 60071(Part 4):2004
/ IS/IEC 60071-4:2004
Insulation coordination - Part 4: Computational guide to
insulation co-ordination and modelling of electrical
networks
17
IS 60071(Part 1):2006
/ IS/IEC 60071-1:2006
Insulation Coordination - Part 1 Definitions, parinciples
and rules
18
IS 60071(Part 1):2004
Insulation coordination – Part 4: Computational guide
to insulation co-ordination and modelling of electrical
networks
19
IS 60071(Part 2):1996
/ IS/IEC 60071-2:1996
Insulation Coordination - Part 2 Application guide (IEC
60071-2:1996)
20
IS 60270:2000
High voltage test techniques - Partial discharge
measurements
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 19(6521)
Insulation coordination for equipment within low
voltage system: Part 1 Principles requirements and
test [First Revision of IS 15382(Part 1)] (IEC 606641:2007)
2
DOC.ETD 19(6522)
Insulation coordination for equipment within low
voltage system : Part 2 Appication guide, Section 1
Explanation of the application of the IEC 60664 series,
dimensioning examples and dielectric testing [First
Revisionof IS 15382(Part 2/Sec 1)]
3
DOC.ETD 19(6523)
Insulation coordination for equipment within low
voltage system: Part 3 Use of coatings, potting or
moulding for protection against pollution [First Revision
of IS 15382(Part 3)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
58
ETD 20 ELECTRICAL INSTALLATIONS
SCOPE - To prepare standards for safety and related matters in designing, erection
and maintenance of electrical installations from the point of view of safety
and good practice that would, amongst other things, promote compatibility
between such standards and those concerning the equipment installed
The work includes electrical installations in buildings for different
occupancies and outdoor sites of temporary or permanent nature and also
installations in the ships
NOTE- The standards to be prepared will not cover codes pertaining to
individual equipment
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
SP 30 : 2011
National Electrical Code (first revision)
2
SP 31 : 1986
Special Publication-Chart on treatment for electricshock
Mar 2011
Code of practice for electrical wiring installations (third
revision)
Mar 2010
3
* IS 732:1989
4
IS 2309:1989
Code of practice for protection of buildings and
allied structures against lightning (second revision)
Mar 2010
5
IS 2551:1982
Danger notice plates (first revision)
Mar 2010
6
* IS 3043:1987
Code of practice for earthing (First Revision)
Mar 2011
7
IS 4648:1968
Guide for electrical layout in residential buildings
Aug 2012
8
IS 5216(Part 1):1982
Recommendations on safety procedures and practices
in electrical work: Part 1 General (first revision)
Mar 2010
9
IS 5216(Part 2):1982
Recommendations on safety procedures and
practices in electrical work: Part 2 Life saving
techniques (first revision)
Mar 2010
10
IS 7689:1989
Guide for the control of undesirable static electricity
(first revision)
Mar 2010
11
IS 7752(Part 1):1975
Guide for improvement of power factor in consumer
installation: Part 1 Low and medium supply voltages
Mar 2011
12
IS 8061:1976
Code of practice for design, installation and
maintenance of service lines upto and including 650 V
Mar 2011
13
IS 8437(Part 1):1992
/ IEC 60479-1:1984
Guide on effects of current passing through human
body: Part 1General aspects(first revision)
Aug 2012
14
IS 8437(Part 2):1992
/ IEC 60479-2:1987
Guide on effects of current passing through human
body : Part 2 Special aspects (first revision).
Aug 2012
15
IS 8884:1978
Code of practice for the installation of electric bells and
call systems
Aug 2012
16
IS 8923:1978
Warning symbol for dangerous voltages
Mar 2010
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
59
1
2
17
IS 8969:1978
Code of practice for installation and maintenance of
impulse and electronic master and slave electric clock
systems
Mar 2011
18
IS 10118(Part 1):1982
Code of practice for selection, installation and
maintenance of switchgear and controlgear :
Part 1 General
Mar 2011
19
IS 10118(Part 2):1982
Code of practice for selection, installation and
maintenance of Switchgear and controlgear :
Part 2 Selection
Mar 2011
20
IS 10118(Part 3):1982
Code of practice for selection, installation and
maintenance of switchgear and controlgear :
Part 3 Installation
Mar 2011
21
IS 10118(Part 4):1982
Code of practice for selection, installation and
maintenance of switchgear and controlgear :
Part 4 Maintenance
Mar 2011
22
IS 10242(Part 1/Sec 1):1997
| IEC 60092-101:1980
Electrical installations in ships: Part 1 General, Section
1 Definitions and general requirements (first revision)
Sep 2012
23
* IS 10242(Part 2/Sec 1):1982
| IEC 60092-201:1980
Electrical installations in ships: Part 2 System design,
Section 1 General
Mar 2014
24
IS 10242(Part 2/Sec 2):1983
| IEC 60092-202:1980
Electrical installations in ships: Part 2 System design,
Section 2 Protection
Sep 2012
25
IS 10242(Part 2/Sec 4):1993
| IEC 60092-204:1987
Electrical installationss in ships: Part 2 System design,
Sec 4 Electric and electrohydraulic steering gear
Mar 2014
26
IS 10242(Part 3/Sec 1):1983
| IEC 60092-301:1980
Electrical installations in ships: Part 3 Equipment,
Section 1 Generators and motors
Sep 2012
27
IS 10242(Part 3/Sec 2):1984
| IEC 60092-302:1980
Electrical installations in ships: Part 3 Equipment,
Section 2 Switchgear and controlgear assemblies
Sep 2012
28
IS 10242(Part 3/Sec 3):1984
| IEC 60092-303:1980
Electrical installations in ships: Part 3 Equipment,
Section 3 Transformers for power and lighting
Sep 2012
29
IS 10242(Part 3/Sec 4):1987
| IEC 60092-304:1980
Electrical installations in ships: Part 3 Equipment,
Section 4 Semi-conductor convertors
Sep 2012
30
IS 10242(Part 3/Sec 5):1990
| IEC 60092-305:1980
Electrical installations inn ships: Part 3 Equipment,
Section 5 Accumulators (storage) batteries
Sep 2012
31
IS 10242(Part 3/Sec 6):1986
| IEC 60092-306:1980
Electrical installations in ships: Part 3 Equipment,
Section 6 Luminaires and accessories
Sep 2012
32
IS 10242(Part 3/Sec 7):1990
| IEC 60092-307:1980
Electrical installations in ships:Part 3 Equipment,
Section 7 Heating and cooking appliances
Sep 2012
33
IS 10242(Part 3/Sec 10):1992
| IEC 60092-350
Electrical installations in ships: Part 3 Equipment,
Section 10 General construction and test requirements
for low voltage shipboard power cables
Mar 2014
34
IS 10242(Part 3/Sec 11):1986
| IEC 60092-35:1983
Electrical installations in ships: Part 3 Equipment,
Section 11 Insulating materials for shipboard power
cables
Sep 2012
35
IS 10242(Part 3/Sec 12):1986
| IEC 60092-352:1979
Electrical installations in ships: Part 3 Equipment,
Section 12 Choice and installation of cables for low
voltage systems
Sep 2012
36
IS 10242(Part 3/Sec 13):1992
| IEC 60092-353:1988
Electrical installations in ships: Part 3 Equipment,
Section 13 Single and multicore cables with extruded
solid insulation for rated voltage 0.6/1 kV
Sep 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
60
37
IS 10242(Part 3/Sec 19):1990
| IEC 60092-359:1987
Electrical installations in ships: Part 3 Equipment,
Section 19 Sheathing materials for telecommunication
and power shipboard cables
Sep 2012
38
IS 10242(Part 3/Sec 23):1987
| IEC 60092-373:1977
Electrical installations in ships: Part 3 Equipment,
Section 23 Shipboard telecommunication cables and
radio frequency cables: Shipboard flexible coaxial
cables
Sep 2012
39
IS 10242(Part 3/Sec 24):1987
| IEC 60092-374:1977
Electrical installations in ships: Part 3 Equipment,
Section 24 Shipboard telecommunication cables and
radiofrequency cables: Telephone cables for nonessential communication services
Sep 2012
40
IS 10242(Part 3/Sec 25):1987
| IEC 60092-375:1977
Electrical installations in ships: Part 3 Equipment,
Section 25 Shipboard telecommunication cables and
radio frequency cables: General instrumentation,
control and communication cables
Sep 2012
41
IS 10242(Part 3/Sec 26):1987
| IEC 60092-376:1983
Electrical installations in ships: Part 3 Equipment,
Section 26 Shipboard telecommunication cables:
Shipboard multicore cables for control circuits
Sep 2012
42
IS 10242(Part 4):1992
| IEC 60092-401:1980
Electrical installations in ships: Part 4 Installation and
test of completed installation
Sep 2012
43
IS 10242(Part 5/Sec 1):1993
| IEC 60092-501:1984
Electrical installations in ships: Part 5 Special features,
Sec 1 Electric propulsion plant
Mar 2014
44
* IS 10242(Part 5/Sec 2):1997
| IEC 60092-502:1999
Electrical installations in ships: Part 5 Special features,
Section 2 Tankers
Sep 2012
45
IS 10242(Part 5/Sec 3):1993
| IEC 60092-503:1975
Electrical installations in ships: Part 5 Special features
Sec 3 ac supply system with voltage in the range
above 1 kV up to and including 11 kV
Mar 2014
46
IS 10242(Part 5/Sec 4):1998
| IEC 60092-504:2001
Electrical installations in ships : Part 5 Special
features, Section 4 Control and instruments
Dec 2013
47
IS 13234:1991
/ IEC 60909:1988
Guide for short circuit current calculations ln threephase ac systems(superseding IS 5728)
Aug 2012
48
IS 13235:1991
/ IEC 60865:1986
Calculation of the effects of short-circuit currents
Superseding IS 5728:1970)
Aug 2012
49
IS 14479:1997
| IEC 60 533:1999
Electromagnetic compatibility of electrical and
electronic installation in ships
Sep 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 20(6443)
Effects of current on human beings and livestock : Part
1 General aspects
2
DOC.ETD 20(6444)
Effects of current on human beings and livestock : Part
2 Special aspects
3
DOC.ETD 20(6445)
Effects of current on human beings and livestock : Part
3 Effects of currents passing strokes on human beings
and livestocks
4
DOC.ETD 20(6446)
Effects of current on human beings and livestock : Part
4 Effects of lightning strokes on human beings and
livestocks
5
DOC.ETD 20(6447)
/ IEC 62305-1:2010
Protection against lightning : Part 1General principles
(IEC 62305-1)
6
DOC.ETD 20(6448)
/ IEC 62305-2:2010
Protection against lightning : Part 2 Risk Management
(IEC 62305-2)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
61
7
DOC.ETD 20(6449)
/ IEC 62305-3:2010
Protection against lightning : Part 3 Physical damage
to structures and life hazard (IEC 62305-3)
8
DOC.ETD 20(6450)
/ IEC 62305-4:2010
Protection against lightning : Part 4 Electrical and
electronic systems within structures (IEC 62305-4)
9
DOC.ETD 20(6451)
Effects of current on human beings and livestock : Part
5 Touch voltage threshold values for physilogycal
effects
10
DOC.ETD 20(6620)
Short-circuit current in three-phase a.c. sustems, Part
0 Calculation of currents
11
DOC.ETD 20(6621)
Short-circuit currents in three-phase a.c. systems –
Part 1: Factors for the calculation of short-circuit
currents according to IEC 60909-0
12
DOC.ETD 20(6622)
Short-circuit currents in three-phase a.c. systems Part 2: Data of electrical equipment for short-circuit
current calculations
13
DOC.ETD 20(6623)
Short-circuit currents in three-phase a.c. systems –
Part 3: Current during two separate simultaneous lineto-earthshort circuits and partial short-circuit current
flowing through earth
14
DOC.ETD 20(6624)
Short-circuit currents in three-phase a.c. systems –
Part 4: Examples for the calculation of short-circuit
currents
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 20(6667)
Code of Practice for Earthing (Second Revision of IS
3043)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 20(5838)
Revision of IS 732 Electrical Wiring Installations
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
62
ETD 21 ELECTRIC WELDING EQUIPMENT
SCOPE - To prepare standards on the construction, performance, testing and safety
requirements for electric welding equipment and accessories for both arc
and resistance type
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1851:1997
| ISO 700:1982
Single Operator type arc welding
transformers (third revision)
Sep 2012
2
IS 2635:1997
dc electric welding generators (third revision)
Sep 2012
3
IS 2641:1989
Electrical welding accessories (first revision)
Jun 2010
4
IS 4559:1993
| ISO 700:1982
Single operator rectifier type dc arc
welding power source (second revision)
Mar 2014
5
IS 4804(Part 1):1968
Resistance welding equipment :
Part 1 Single phase transformers
Jun 2010
6
IS 4804(Part 2):1968
Resistance welding equipment:
Part 2 Single phase rocker-arm spot welding machines
Jun 2010
1
7
IS 4804(Part 3):1969
Resistance welding equipment:
Part 3 Single phase spot and
projection welding machines
Jun 2010
1
8
IS 4804(Part 4):1973
Resistance welding equipment:
Part 4 Single phase stationary, press type
roll-spot and seam welding machines
Jun 2010
Single operator ac/dc arc welding
power source (first revision)
Mar 2014
9
IS 6008:1989
| IEC 700:1982
10
IS 7931(Part 1):1975
Automatic and semi-automatic welding equipment
with self-adjusting arcs (MIG/MAG processes) :
Part 1 dc welding generator power source
Mar 2014
11
IS 7931(Part 2):1975
Automatic and semi-automatic welding equipment
with self-adjusting arcs (MIG/MAG Processes):
Part 2 Transformer rectifier power source
Mar 2014
1
12
IS 7931(Part 3):1975
Automatic and semi-automatic welding equipment with
self-adjusting arcs (MIG/MAG Processes):
Part 3 Welding gun and ancillary equipment
Mar 2014
1
Plugs, sockets and terminal arrangements
and welding cable connectors for manual
welding equipment (first revision)
Mar 2014
13
IS 8804:1993
| IEC 501:1975
14
IS 9604:1994
Tungsten-inert gas (TIG) welding equipment
Mar 2014
15
IS 13339:1992
Multi-operator type arc welding transformers
Sep 2012
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 21(6738)
Arc welding equipment - Part 1: Welding power
sources (IEC 60974-1:2012)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
63
2
DOC.ETD 21(6739)
Arc welding equipment – Part 2: Liquid cooling
systems (IEC 60974-2:2013)
3
DOC.ETD 21(6740)
Arc welding equipment Part 3: Arc striking and
stabilizing devices (IEC 60974-3:2013)
4
DOC.ETD 21(6741)
Arc welding equipment – Part 4: Periodic inspection
and testing (IEC 60974-4:2010)
5
DOC.ETD 21(6742)
Arc welding equipment – Part 5: Wire Feeders (IEC
60974-5:2013)
6
DOC.ETD 21(6743)
Arc welding equipment – Part 6: Limited duty
equipment’ (IEC 60974-6:2010)
7
DOC.ETD 21(6744)
Arc welding equipment – Part 8: Gas consoles for
welding and plasma cutting systems (IEC 609748:2009)
8
DOC.ETD 21(6745)
Arc welding equipment – Part 10: Electromagnetic
compatibility (EMC) requirements (IEC 60974-10:2014)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
64
ETD 22 ELECTRICAL APPARATUS FOR EXPLOSIVE ATMOSPHERES
SCOPE - To prepare guidelines and requirements for electrical apparatus for use
where there is a hazard due to the possible presence of ignitable gas,
vapour liquid particles or dust in the atmosphere.
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
* IS 4051:1967
Code of practice for installation and maintenance of
electrical equipment in mines
Oct 2011
2
IS 5571:2009
| IEC 60079-14(2002)
Guide for selection and installation of electrical
equipment in hazardous areas (other than mines
(third revision)
Feb 2014
3
IS 5572:2009
| IEC 60079-10(2002)
Classification of hazardous areas (other than mines)
having flammable gases and vapours for electrical
installation (third revision of IS 5572)
Jan 2014
Miners' cap lamp assemblies (incorporating lead acid
type batteries) (first revision)
Oct 2011
Guide for selection of electrical and electronic
equipment for coal mines
Oct 2011
Exploders
Oct 2011
4
IS 5679:1986
5
* IS 9559:1980
6
IS 9836:1981
7
* IS 11064:1984
| IEC 60079-13(1982)
Guide for construction and use of rooms or buildings
protected by pressurization for installation of electrical
apparatus for explosive gas atmospheres
Oct 2011
8
* IS 14774(Part 1):2000
| IEC 62086-1
Resistance trace heating in potentially explosive
atmospheres: Part 1 General and testing requirements
Apr 2010
9
IS 14774(Part 2):2000
| IEC 62086-2
Resistance trace heating in potentially explosive
atmospheres: Part 2 Informative application guide for
design, installation and maintenance
Apr 2010
Guide to the use of electrical apparatus for potentially
explosive atmospheres in the presence of combustible
dusts
Sep 2012
10
IS 15142:2002
11
IS 60079:2007
/ IS/IEC 60079-0:2007
Explosive Atmospheres. Part 0: Equipment - General
Requirements (First Revision)
May 2012
12
IS 60079(Part 1):2007
/ IS/IEC 60079-1:2007
Explosive atmospheres : Part 1 Equipment protection
by flameproof enclosures "d" (superseding IS
2148:2004 )
Dec 2012
13
IS 60079(Part 2):2007
/ IS/IEC 60079-2:2007
Explosive atmospheres: Part 2 Equipment protection
by pressurized enclosure "p" (superseding IS
7389:2004)
Jul 2009
14
IS 60079(Part 26):2006
/ IS/IEC 60079-26:2006
Explosive Atmospheres Part 26 Equipment With
Equipment Protection Level EPL "Ga"
Feb 2013
15
IS 60079(Part 27):2013
/ IS/IEC 60079-27:2013
Explosive Atmospheres Part 27 Fieldbus Intrisically
Safe Concept (FISCO)
Feb 2013
16
IS 60079(Part 5):2007
/ IS/IEC 60079-5:2007
Explosive atmospheres: Part 5 Equipment protection
by powder filling "q" (superseding IS 7724:2004)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
65
Jul 2009
1
17
IS 60079(Part 6):2007
/ IS/IEC 60079-6:2007
Explosive atmospheres: Part 6 Equipment protection
by oil immersion "o" (superseding IS 7693:2004)
Mar 2011
18
IS 60079(Part 7):2006
/ IS/IEC 60079-07:2006
Explosive atmospheres: Part 7 Equipment protection
by increased safety "e" (superseding IS 6381:2004)
Sep 2013
19
IS 60079(Part 11):2006
/ IS/IEC 60079-11:2006
Explosive atmospheres: Part 11 Equipment protection
by intrinsic safety "i" (superseding IS 5780:2002)
Sep 2013
20
* IS 60079(Part 15):2005
/ IS/IEC 60079-15:2005
Electrical apparatus for explosive gas atmospheres :
Part 15 Construction, test and marking of type of
protection "n" electrical apparatus (superseding
IS 8289)
Oct 2012
21
IS 60079(Part 16):1990
/ IS/IEC 60079-16:1990
Electrical apparatus for explosive gas atmospheres:
Part 16 Artificial ventilation for the protection of
analyzer(s) houses
Apr 2013
22
IS 60079(Part 17):2007
/ IS/IEC 60079-17:2007
Explosive atmospheres : Part 17 Electrical
installations inspection and maintenance
Sep 2013
23
IS 60079(Part 18):2009
/ IS/IEC 60079-18:2007
Explosive Atmospheres Part 18 Equipment Protection
By Encapsulation "m" (First Revision)
Oct 2012
24
* IS 60079(Part 19):2006
/ IS/IEC 60079-19:2006
Explosive atmospheres : Part 19 Repair, overhaul
and reclamation
Jul 2013
25
IS 60079(Part 20/Sec 1):2000
/ IS/IEC60079-20-1:00
Explosive Atmospheres Part 20 material
Characteristics For Gas and Vapour Classification
Section 1 Test Methods and Data(Superseding IS
7820, IS 9570, IS 9735, IS/IEC 60079-20)
Nov 2012
26
* IS 60079(Part 25):2003
/ IS/IEC 60079-25:2003
Electrical apparatus for explosive gas atmospheres :
Part 25 Intrinsically safe systems
Nov 2010
27
IS 60079(Part 28):2000
/ IS/IEC 60079-28:2000
Explosive Atmospheres Part 28 Protection of
Equipment And Transmission Systems Using Optical
Radiation
Nov 2012
28
IS 60079(Part 29/Sec 1):2007
/ IS/IEC 60079-29-1:07
Explosive atmospheres - Part 29-1: Gas detectors Performance requirements of detectors for flammable
gases
Mar 2012
29
IS 60079(Part 29/Sec 2):2007
/ IS/IEC 60079-29-2:07
Explosive atmospheres - Part 29-2: Gas detectors selection, installations, use and maintenance of
detectors for flammable gases and oxygen
Dec 2011
30
IS 60079(Part 30/Sec 1):2007
/ IS/IEC 60079-30-1:07
Explosive Atmospheres Part 30 Electrical Resistance
Trace Heating Section 1 General And Testing
Requirements (Superseding IS 14774 (Part 1)
Nov 2012
31
IS 60079(Part 30/Sec 2):2007
/ IS/IEC 60079-30-2:07
Explosives Atmospheres Part 30 Electrical
Resistance Trace Heating Section 2 Application
Guide for Design , Installation And Maintenance
(Superseding IS 14774 (Part 2)
Nov 2012
32
IS 60079(Part 31):2008
/ IS/IEC 60079-31:08
Explosives Atmospheres Part 31 Equipment Dust
Ignition Protection By Enclosures"T"
Nov 2012
33
IS 61241(Part 0):2004
/ IS/IEC 61241-0:2004
Electrical apparatus for use in the presence of
combustible dust: Part 0 General requirements
(Superseding IS 14154(Part 1) : 1996
May 2014
34
IS 61241(Part 1):2004
/ IS/IEC 61241-1:2004
Electrical apparatus for use in the presence of
combustible dust: Part 1: Protection by enclosures “tD”
Apr 2014
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
66
35
IS 61241(Part 2/Sec 1):2000
/ IS/IEC 61241-2-1:94
Electrical apparatus for use in the presence of
combustible dust: Part 2 Test methods, Section 1
Method for determining the minimum ignition
temperatures of dust (Superseding IS 12315-2:1998)
Oct 2009
36
IS 61241(Part 2/Sec 3):1994
/ IS/IEC 61241-2-3:94
Electrical apparatus for use in the presence of
combustible dust: Part 2 Test methods, Section 3
Method for determining minimum ignition energy of
dust/air mixtures
Apr 2014
37
IS 61241(Part 4):2001
/ IS/IEC 61241-4 :2001
Electrical apparatus for use in the presence of
combustible dust: Part 4 Type of protection “pD”
Dec 2009
38
IS 61241(Part 10):2004
/ IS/IEC 61241-10:2004
Electrical apparatus for use in the presence of
combustible dust: Part 10 : Classification of areas
where combustible dusts are or may be present
Apr 2014
39
IS 61241(Part 11):2005
/ ISEC 61241-11:2005
Electrical apparatus for use in the presence of
combustible dust: Part 11 Protection by intrinsic safety
“iD”
May 2014
40
IS 61241(Part 14):2004
/ IS/IEC 61241-14:2004
Electrical apparatus for use in the presence of
combustible dust: Part 14 Selection and installation
(Superseding IS 14154(Part 2) : 1997 & IS 13408-1 :
1992)
May 2014
41
IS 61241(Part 18):2004
/ IS/IEC 61241-18:2004
Electrical Apparatus for Use in the Presence of
May 2014
Combustible Dust: Part 18 Protection by Encapsulation
“mD”
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 22(6400)
/ IEC 60079-10- (2009)
Explosive Atmospheres – Part 10-2: Classification of
areas –Combustible dust atmospheres
2
DOC.ETD 22(6401)
/ IEC 60079-13 (2010)
Explosive Atmospheres - Part 13: Equipment
protection by pressurized room "p"
3
DOC.ETD 22(6402)
/ IEC 60079-15 (2010)
Explosive Atmospheres - Part 15: Equipment
protection by type of protection "n"
4
DOC.ETD 22(6403)
/ IEC 60079-19 (2010)
Explosive Atmospheres - Part 19: Equipment repair,
overhaul and reclamation
5
DOC.ETD 22(6404)
/ IEC 60079-25 (2010)
Explosive Atmospheres - Part 25: Intrinsically safe
electrical systems
6
DOC.ETD 22(6405)
/ IEC 60079-29-4(2009)
Explosive Atmospheres Part 29-4: Gas detectors Performance requirements of open path detectors for
flammable gases
7
DOC.ETD 22(6406)
/ IEC 61241-2-2(1994)
Electrical apparatus for use in the presence of
combustible dust - Part 2 : Test methods – Section 2:
Method for determining the electrical resistivity of dust
in layers
8
DOC.ETD 22(6590)
/ IEC 60079-0 : 2011
Explosive Atmospheres –Part 0: General
requirements (Second revision)
9
DOC.ETD 22(6591)
/ IEC 60079-11 (2012)
Explosive Atmospheres – Part 11: protection by
intrinsic safety “i” (First revision)
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 22(6588)
/ IEC 60079-35-1 (2011
Explosive Atmospheres –Part 35-1 : Caplights for use
in mines susceptible to firedamp – General
requirements – Construction and testing in relation to
the risk of explosion
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
67
2
DOC.ETD 22(6589)
/ IEC 60079-35-2 (2011
Explosive Atmospheres – Part 35-2 : Caplights for
use in mines susceptible to firedamp –
Performance and other safety-related matters
DRAFT STANDARDS FORMULATED
1
DOC.ETD 22(6191)
Code of practice for electrical and electronic
equipments for belowground coal mines
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
68
ETD 23 ELECTRIC LAMPS AND THEIR AUXILIARIES
SCOPE - To prepare standards for all types of electric lamps, caps and their
auxiliaries (luminaires are excluded)
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 418:2004
| IEC 60064(1993)
2
IS 897:1982
3
IS 1569:1976
| IEC 566
4
IS 1901:1978
5
IS 2215:2006
| IEC 60155 (1993)
Tungsten filament lamps for domestic and similar
general lighting purposes (fourth revision)
Mar 2014
4
Tungsten filament electric lamps for railway rolling
stock (second revision)
Mar 2010
3
Capacitors for use in tubular fluorescent
high pressure mercury and low pressure sodium
vapour discharge lamp circuits ( first revision)
Jul 2011
1
Visual indicator lamps (first revision)
Oct 2012
1
Starters for fluorescent lamps (third revision)
Jun 2010
Dec 2010
6
IS 2261:1975
Lamps for flashlights (first revision)
7
IS 2262:1963
Transformers for high voltage luminous discharge
tubes
Jul 2011
8
IS 2407:1963
Photometric integrators
Oct 2012
1
9
IS 2418(Part 1):1977
| IEC 81(1974)
Tubular fluorescent lamps for general lighting service:
Part 1 Requirements and tests (first revision)
Dec 2010
8
10
IS 2418(Part 2):1977
| IEC 81(1974)
Tubular fluorescent lamps for general lighting service :
Part 2 Standard lamp data sheets (first revision)
Jul 2011
3
11
IS 2418(Part 3):1977
| IEC 61-1(1969)
Tubular fluorescent lamps for general lighting service :
Part 3 Dimensions of G-5and G-13 bi-pin caps (first
revision)
Jul 2011
1
12
IS 2418(Part 4):1977
| IEC 61-3(1969)
Tubular fluorescent lamps for general lighting service:
Part 4 Go and no-go gauges for G-5 and
G-13 bi-pin caps (first revision)
Oct 2012
13
IS 2592:1980
Lamps for lighting on board ships (first revision)
Oct 2012
14
IS 2596:2004
Bulbs (lamps) for miners cap lamps (second revision)
Sep 2009
15
IS 6616:1982
| IEC 262(1969)
Ballasts for high pressure mercury vapour lamps
(first revision)
Jul 2011
1
16
IS 6701:1985
| IEC 61-1(1969)
Tungsten filament miscellaneous electric lamps
(first revision)
Jul 2011
2
17
IS 7027:1984
| IEC 458 (1982)
Transistorized ballasts for fluorescent lamps
(first revision)
Jul 2011
18
IS 8685:1977
| IEC 60434 (1973)
Aircraft lamps
Jul 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
69
19
IS 8901:1978
20
21
22
Lamps for aerodrome lighting fittings
Jul 2011
IS 8913:1978
| IEC 360(1971)
Methods of measurement of lamp cap temperature rise
Oct 2012
IS 9206:1979
| IEC 60061-1(1969)
Dimensions of caps for tungsten filament
general service electric lamps
Dec 2010
Electric lamps for railway signalling
Oct 2012
IS 9589:1980
1
4
23
IS 9900(Part 1):1981
| IEC 188(1974)
High pressure mercury vapour lamps:
Part 1 Requirements and test
(Superseding IS:2183 and IS:7023)
Oct 2012
4
24
IS 9900(Part 2):1981
| IEC 188(1974)
High pressure mercury vapour lamps: Part 2 Standard
lamp data sheets (superseding IS: 2183 and IS: 7023)
Oct 2012
1
25
IS 9900(Part 3):1981
| IEC 188(1974)
High pressure mercury vapour lamps :
Part 3 Dimensions of lamp caps
(superseding IS:2183 and IS:7023)
Oct 2012
26
IS 9900(Part 4):1981
| IEC 61-3(1969)
High pressure mercury vapour lamps :
Part 4 Go and no-go gauges of lamp caps
(superseding IS:2183 and IS:7023)
Oct 2012
27
IS 9974(Part 1):1981
| IEC 662(1980)
High pressure sodium vapour lamps :
Part 1 General requirements and tests
Oct 2012
4
28
IS 9974(Part 2):1981
| IEC 662(1980)
High pressure sodium vapour lamps :
Part 2 Standard lamp data sheets
Oct 2012
2
Lamp (bulb) cycle dynamo
Oct 2012
29
IS 11980:1987
30
IS 12449(Part 1):1988
| IEC 60926 (1995)
Starting devices (other than glow starters):
Part 1 General and safety requirements
Jun 2013
1
31
IS 12449(Part 2):1988
| IEC 60927 (1996)
Starting devices (other than glow starters):
Part 2 Performance requirements
Jun 2013
1
Filaments for general service lamps-Guide
(first revision)
Mar 2011
1
32
IS 12897:2001
33
IS 12948:1990
| IEC 60357(1982)
Tungsten halogen lamps (non-vehicle)
34
IS 13021(Part 1):1991
| IEC 60928(1990)
AC supplied electronic ballasts for tubular florescent
lamps: Part 1 General and safety requirements
Dec 2010
1
35
IS 13021(Part 2):1991
| IEC 60929(1990)
AC supplied electronic ballasts for tubular florescent
lamps: Part 2 Performance requirements
Dec 2010
2
36
IS 14897:2000
| IEC 60887(1988)
Glass bulb designation system for lamps-Guide
Dec 2010
1
37
IS 15111(Part 1):2002
| IEC 60968(1988)
Self ballasted lamps for general lighting services :
Part 1 Safety requirements
Jan 2012
4
38
IS 15111(Part 2):2002
| IEC 60969(1988)
Self ballasted lamps for general lighting services :
Part 2 Performance requirements
Feb 2012
9
39
IS 15518(Part 1):2004
| IEC 60432-1 (1999)
Safety requirements for incandescent lamps :
Part 1 Tungsten filament lamps for domestic and
similar general lighting purposes
Aug 2009
3
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
70
Jul 2011
40
IS 15687(Part 1):2006
| IEC 61199 (1999)
Single-capped fluorescent lamps: Part 1 Safety
requirements
Nov 2011
41
IS 15882:2009
Ballasts for discharge lamps (excluding tubular
fluorescent lamps) - Performance requirements
[Superseding IS 6616 :1982]
Dec 2009
42
IS 15885(Part 1):2011
Safety of lamp controlgear: Part 1 General
requirements
May 2011
43
IS 15885(Part 2/Sec 1):2011
| IEC 61347-2-1 (2000)
Safety of lamp controlgear: Part 2 Particular
requirements, Sec 1 Starting devices (other than glow
starters
Feb 2011
44
IS 15885(Part 2/Sec 3):2011
| IEC 61347-2-3 (2000)
Safety of lamp controlgear: Part 2 Particular
requirements, Sec 3 ac supplied electronic ballasts for
fluorescent lamps
Jan 2011
45
IS 15885(Part 2/Sec 8):2011
| IEC 61347-2-8 (2000)
Safety of lamp controlgear: Part 2 Particular
requirements, Sec 8 Ballasts for fluorescent lamps
Jan 2011
46
IS 15885(Part 2/Sec 9):2011
| IEC 61347-2-9 (2000)
Safety of lamp controlgear: Part 2 Particular
requirements, Sec 9 Ballasts for discharge lamps
(excluding fluorescent lamps)
Jan 2011
47
IS 15885(Part 2/Sec 13):2012
/ IEC 61347-2-13(2006)
Lamp Control gear Part 2 Particular Requirements.
Section 13 D.C. or A.C. Supplied Electronic
Controlgear For Led Modules
Feb 2012
48
IS 15906:2010
Measurement of mercury level in fluorescent lamps
May 2011
49
IS 15967(Part 1):2013
Capacitor for use in tubular fluorescent and other
discharge lamps circuits : Part 1 Safety requirements
Jun 2013
50
IS 15967(Part 2):2013
Capacitor for tubular fluorescent lamps:
Part 2 Performance requirements
May 2013
51
IS 15968:2013
Ballasts for tubular fluorescent lamps - Performance
requirements
May 2013
52
IS 15974:2013
Auxiliaries for lamps - Starting devices (other than
glow starters) - Performance requirements
Dec 2013
53
IS 16101:2012
General Lighting - LEDs and LED Modules Terms and Definitions
Feb 2012
54
IS 16102(Part 1):2012
Self Ballasted LED-Lamps for General Lighting
Services Part 1 Safety Requirements
Feb 2012
1
55
IS 16102(Part 2):2012
Self Ballasted LED-Lamps for General Lighting
Services Part 2 Performance Requirements
Feb 2012
1
56
IS 16103(Part 1):2012
Led Modules for General Lighting- Safety Specification
Feb 2012
57
IS 16103(Part 2):2012
Led Modules for General Lighting Part 2 Performance
Requirements
Mar 2012
58
IS 16104:2012
DC or AC Supplied Electronic Control Gear for LED
Modules - Performance Requirements
Feb 2012
59
IS 16105:2012
Method of Measurement of Lumen Maintenance of
Solid State Light (LED) Sources
Feb 2012
60
IS 16106:2012
Method Of Electrical And Photometric Measurements
Of Solid- State Lighting (Led) Products
Feb 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
71
61
IS 16108:2012
/ IEC 62471 (2006)
Photobiological Safety of Lamp and Lamp Systems
Feb 2012
62
IS 16148:2014
Metal halide lamps - Performance Specification
Feb 2014
63
IS 16166:2014
Sample Preparation For Measurement of Mercury
Level In Fluorescent Lamps
Feb 2014
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 23(6579)
ac supplied electronic ballasts for tubular fluorescent
lamps - Performance requirements
2
DOC.ETD 23(6658)
/ IEC 61195 (2012)
Double Capped – Fluorescent Lamps – Safety
Specifications
3
DOC.ETD 23(6659)
/ IEC/TR 61341 (2010)
Method of Measurement of Centre Beam Intensity And
Beam ─ Angles(S) of Reflector Lamps
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 23(6062)
Double-capped fluorescent lamps for general lighting
service - Specification: Part 2 Performance
requirements [second revision of IS 2418 (Part 2)]
DRAFT STANDARDS FORMULATED
1
DOC.ETD 23(6528)
Double-Capped Led Lamps For General Lighting
Services – Part 1 Safety Requirements
2
DOC.ETD 23(6564)
Single Capped Fluorescent Lamps
Performance Requirements
Part 2
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
72
ETD 24 ILLUMINATION ENGINEERING AND LUMINAIRES
SCOPE - To prepare codes of practice for interior and exterior lighting and standards
for luminaires (including luminaires for use in hazardous area, aviation
lighting, emergency lighting etc.
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
SP 72 : 2010
National Lighting Code
2
IS 1944(Part 5):1981
Code of practice for lighting of public thoroughfare:
Part 5 Lighting for grade separated junctions,
bridges and elevated roads (Group D)
Mar 2013
3
IS 1944(Part 6):1981
Code of practice for lighting of public thoroughfare:
Part 6 Lighting for towns and city centres and
areas of civic importance (Group E)
Mar 2013
4
IS 1944(Part 7):1981
Code of practice for lighting of public thoroughfare:
Part 7 Lighting for roadswith special requirements
(Group F)
Mar 2013
5
IS 1944(Part 1 & 2):1970
Code of practice for lighting of public thoroughfare:
Parts 1 and 2 For main and secondary roads (Group A
and B) (first revision) (Parts 1 and 2 in one volume)
Mar 2013
6
IS 2672:1966
Code of practice for library lighting
May 2010
7
IS 3528:1966
Waterproof electric lighting fittings
May 2010
8
IS 3553:1966
Watertight electric lighting fittings
May 2010
9
IS 3646(Part 1):1992
Code of practice for interior illumination:
Part 1 General requirements and recommendations
for working interiors (first revision)
Mar 2013
10
IS 3646(Part 2):1966
Code of practice for interior illumination: Part 2
Schedule of illumination and glare index
Mar 2013
11
IS 3646(Part 3):1968
Code of practice for interior illumination: Part 3
Calculation of coefficients of utilization by the BZ
method
Mar 2013
12
IS 4347:1967
Code of practice for hospital lighting
May 2010
13
IS 5077:1969
Decorative lighting outfits
May 2010
14
IS 6665:1972
Code of pratice for industrial lighting
May 2010
15
IS 7537:1974
Road traffic signals
Mar 2013
16
IS 7569:1987
Cast acrylic sheets for use in luminaires (first revision)
Mar 2013
17
IS 7785(Part 1):1975
Elevated type aerodrome lighting fittings: Part 1
General requirements
Mar 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
73
2
1
18
IS 7785(Part 2):1976
Elevated type aerodrome lighting fittings:
Part 2 Fixed focus high intensity bi-directional
runway edge lighting fittings
Mar 2013
19
IS 7785(Part 3):1976
Elevated type aerodrome lighting fittings:
Part 3 Low intensity runway edge lighting fittings
Mar 2013
20
IS 7785(Part 4/Sec 1):1981
Elevated type aerodrome lighting fittings:
Part 4 Angle of approach lights,
Section 1 Visual approach slope indicators
Mar 2013
21
IS 7785(Part 5/Sec 1):1981
Elevated type aerodrome lighting fittings:
Part 5 Approach lighting fittings,
Section 1 High intensity elevated approach lighting
fittings
Mar 2013
22
IS 7785(Part 6/Sec 1):1981
Elevated type aerodrome lighting fittings:
Part 6 Taxiway lights, Section 1 Low intensity
omni-directional elevated taxiway lighting fittings
Mar 2013
23
IS 8030:1976
| IEC 162(1972)
Luminaires for hospitals
Mar 2013
24
IS 9583:1981
| IEC 598-2-22(1980)
Emergency lighting units
Mar 2013
25
IS 10322(Part 1):2014
| IEC 60598-1(2003-10)
Luminaires: Part 1 General requirements and tests
[first revision of IS 10322 (Part 1 to Part 4)]
Feb 2014
26
IS 10322(Part 2):1982
| IEC 598-1(1979)
Luminaires: Part 2 Constructional requirements
May 2010
27
IS 10322(Part 3):1984
Luminaires:Part 3 Screw and screwless terminations
(superseding IS:6585)
May 2010
28
IS 10322(Part 4):1984
| IEC 598-1(1979)
Luminaires: Part 4 Methods of tests
May 2010
29
IS 10322(Part 5/Sec 1):2012
| IEC 60598-2-1(1979)
Luminaires: Part 5 Particular requirements, Sec 1
Fixed general purpose luminaires (First revision)
Mar 2012
30
IS 10322(Part 5/Sec 2):2012
| IEC 60598-2-2 (1979)
Luminaires: Part 5 Particular requirements,
Sec 2 Recessed luminaires (First revision)
Mar 2012
31
IS 10322(Part 5/Sec 3):2012
| IEC 60598-2-3 (1979)
Luminaires: Part 5 Particular requirements,
Sec 3 Luminaires for road and street lighting
(First revision)
Mar 2012
32
IS 10322(Part 5/Sec 4):1987
Luminaires: Part 5 Particular requirements,
Sec 4 Portable General Purpose Luminaires
May 2010
33
IS 10322(Part 5/Sec 5):2013
| IEC 60598-2-5
Luminaires: Part 5 Particular requirements,
Section 5 Flood lighting (First revision)
Jul 2013
34
IS 10322(Part 5/Sec 6):2013
Luminaires: Part 5 Particular requirements,
Sec 6 Hand lamps
Jul 2013
35
IS 10322(Part 5/Sec 7):2013
Luminaires: Part 5 Particular requirements,
Sec 7 Lighting chains
Jul 2013
36
IS 10322(Part 5/Sec 8):2013
Luminaires: Part 5 Particular requirements,
Sec 8 Emergency lighting
Jul 2013
37
IS 10894:1984
Code of practice for lighting of educational institutions
Jul 2013
38
IS 10947:1984
Code of practice for lighting for ports and harbours
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
74
May 2010
1
1
39
IS 11071(Part 1):1984
Inset type aerodrome lighting fittings:
Part 1 General requirements and tests
May 2010
40
IS 11071(Part 2):1984
Inset type aerodrome lighting fittings:
Part 2 Runway centre line lighting fittings
May 2010
41
IS 11071(Part 3):1984
Inset type aerodrome lighting fittings:
Part 3 Approach lighting fittings
May 2010
42
IS 11071(Part 4):1984
Inset type aerodrome lighting fittings:
Part 4 Touchdown zone lighting fittings
May 2010
43
IS 11116:1984
Code of practice for lighting for airport aprons
May 2010
44
IS 11472(Part 1):1985
Artificial day light for the assessment of colours:
Part 1 Illuminant for colour matching and colour
appraisal
Mar 2013
45
IS 11472(Part 2):1985
Artificial day light for the assessment of colours:
Part 2 Viewing conditions for graphic arts industry
Mar 2013
46
IS 12290(Part 0):1987
Isolating transformers for airport lighting
Mar 2013
47
IS 12291:1987
Constant current regulators for airport systems
Mar 2013
48
IS 12309(Part 1):1988
Code of practice for installation and maintenance of
aerodrome lighting fittings: Part 1 Installation
Mar 2013
49
IS 12309(Part 2):1988
Code of practice for installation and maintenance of
aerodrome lighting fittings: Part 2 Maintenance
Mar 2013
50
IS 13383(Part 1):1992
Methods of photometry of luminaires:
Part 1 For use in interior lighting
May 2010
51
IS 13383(Part 2):1992
Methods of photometry of luminaires:
Part 2 For road and street lighting
Oct 2010
52
IS 13383(Part 3):1992
Methods of photometry of luminaires:
Part 3 For flood lighting
May 2010
53
IS 16107(Part 1):2012
Luminaires Performance Part 1 - General
Requirements
Mar 2012
54
IS 16107(Part 2/Sec 1):2012
Luminaires Performance Part 2 Particular
Requirements - Section 1 : LED Luminaire
Mar 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 24(6120)
Luminaires: Part 5 Particular requirements,
Sec 4 Portable General Purpose
[first revision of IS 10322 (Part 5/Sec 4)]
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 24(6305)
Led Luminairies for General Lighting purposes Part 1 :
Safety Requirements
DRAFT STANDARDS FORMULATED
1
DOC.ETD 24(6487)
Led-Luminaires Part 3 Particular Equirements
Section 3 Street Lighting
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
75
1
ETD 25 LIFTS AND ESCALATORS
SCOPE - To prepare standards and codes of practice for electrically operated lifts and
escalators, including equipment and components
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 4591:1968
Code of practice for installation and maintenance of
escalators
Feb 2012
2
IS 8216:1976
Guide for inspection of lift wire ropes
Feb 2012
3
IS 14665(Part 1):2000
Electric traction lifts :Part 1 Outline dimensions
(superseeding IS 3534:1976)
Oct 2010
4
IS 14665(Part 2/Sec 1 & 2):2000 Electric traction lifts :Part 2 Code of prtactice for
installation , operation and maintenance, Section 1
Passengers and goods lifts (Superseeding IS
1860:1980) ,Section 2 Service lifts (superseeding IS
6620:1972)
Oct 2010
3
5
IS 14665(Part 3/Sec 1 & 2):2000 Electric traction lifts :Part 3 Safety rules , Section 1
Passenger and goods lifts (superseeding IS
4666:1980), Section 2 Service lifts (superseeding IS
6383:1971)
May 2010
2
6
IS 14665(Part 4/Sec 1-9):2001
Electric traction lifts :Part 4 Components, Section 1 Lift
buffers (superseding IS 9803:1981), Section 2 Lift
guide rails and guide shoes (superseding IS
10191:1982 and IS 11615:1986,Section 3 Lift car
frame, car counterweight and suspension
(superseding IS 11706:1986), Section 4 Lift safety
gears and governors (superseding IS 9878:1981),
Section 5 Lift retiring cam (superseding IS
10448:1983), Section 6 Lift doors, locking devices and
contacts (superseding IS 7759:1975 and 11633:1986),
Section 7 Lift machines and brakes (superseding IS
10913:1984), Section 8 Lift wire ropes, Section 9
Controller and operating devices
Jun 2011
4
7
IS 14665(Part 5):1999
Electric traction lifts:Part 5 Inspection manual
Mar 2014
8
IS 14671:1999
Code of practice for instalation and maintenance of
hydraulic lifts
Mar 2014
9
IS 15259:2002
Installation and maintenance of home lifts - Code of
practice
Nov 2012
10
IS 15330:2003
Code of practice for installation and maintenance of
lifts for handicapped persons
Mar 2013
11
IS 15785:2007
Code of practice for installation and maintenance of
lifts without conventional machine rooms
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 25(6607)
Escalators and moving walks Part 1: Safety
requirements
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
76
1
1
2
DOC.ETD 25(6608)
Escalators and moving walks Part 2 : Guide for
Planning and Selection
3
DOC.ETD 25(6609)
Escalators and moving walks Part 3 : Construction and
Installation
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 25(6598)
Installation And Maintenance of Lifts For Handicapped
Persons Code of Practice (First Revision of IS 15330)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 25(6599)
Electric Traction Lifts. Part 6 Replacement of existing
passenger and goods passenger lifts in existing
building
2
DOC.ETD 25(6611)
Guide for Maintenance for lift and escalators
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
77
ETD 28 SOLAR PHOTOVOLTAIC ENERGY SYSTEMS
SCOPE - To prepare standards for systems of photovoltaic conversion of solar energy
into electrical energy and for all the elements in the entire photovoltaic
energy systems
In this context, the concept photovoltaic energy systems includes the entire
field from light input to solar cell and including the interface with the electrical
system(s) to which energy is supplied
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 12762(Part 1):2010
/ IEC 60904-1:2006
Photovoltaic devices: Part 1 Measurement of
photovoltaic current-voltage characteristics
[first revision)
Jan 2010
2
IS 12762(Part 2):2013
/ IEC 60904-2 (2007)
Photovoltaic devices: Part 2 Requirements for
reference solar cells (First Revision of IS 12762 (Part
2))
Jun 2013
3
IS 12762(Part 3):2013
/ IEC 60904-3 (2008)
Photovoltaic devices Part 3 Measurement principles
for terrestrial (PV) solar devices with reference
spectral irradiance data (First Revision of IS 12762
(Part 3)
Jun 2013
4
IS 12762(Part 4):2014
5
IS 12762(Part 5):2010
/ IEC 60904-5:1993
Photovoltaic devices: Part 5 Determination of the
equivalent cell temperature (ECT) of photovoltaic (PV)
devices by the open-circuit voltage method
Jan 2010
6
IS 12762(Part 7):2013
/ IEC 60904-7 (2008 )
Photovoltaic devices: Part 7 Computation of spectral
mismatch error introduced in the testing of a
photovoltaic device
Jun 2013
7
IS 12762(Part 8):2010
/ IEC 60904-8:1998)
Photovoltaic devices: Part 8 Measurement of spectral
response of a photovoltaic (PV) device
Jan 2010
8
IS 12762(Part 9):2010
/ IEC 60904-9:2007
Photovoltaic devices: Part 9 Solar simulator
performance requirments
Jan 2010
9
IS 12762(Part 10):2010
/ IEC 60904-10:1998
Photovoltaic devices: Part 10 Methods of linearity
measurment
Jan 2010
Photovoltaic Devices Part 4 : Reference solar
devices - Procedures for establishing calibration
traceability
10
IS 12763:2013
Procedures for temperature and irradiance corrections
to measured I-V characteristics of crystaline silicon
photovoltaic devices
Jun 2013
11
IS 12834:2013
Solar photovoltaic energy systems - Terms and
symbols (first revision of IS 12834)
Jun 2013
12
** IS 14153:1994
Guide for general description of photovoltaic (PV)
power generating systems
Apr 2009
13
IS 14244:1995
/ IEC 61194(1992)
Characteristic parameters of stand alone photovoltaic
(PV) systems
Jan 2010
14
IS 14286:2010
/ IEC 61215:2005
Crystalline silicon terrestrial photovoltaic (PV)
modules - Design qualiication and type approval
(first revision)
Jan 2010
15
IS 16077:2013
/ IEC 61646 (2008 )
Thin-film terrestrial photovoltaic (PV) modules Design qualification and type approval
Jun 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
78
16
IS 61683:1999
/ IEC 61683:1999
Photovoltaic systems - Power conditioners - Procedure
for measuring efficiency
Feb 2010
17
IS 61701:1995
/ IEC 61701:1995)
Salt mist corrosion testing of photovoltaic (PV) modules Feb 2010
18
IS 61724:1998
/ IEC 61724:1998
Photovoltaic system performance monitoring Guidelines for measurment, data exchange and
analysis
Feb 2010
19
IS 61725:1997
/ IS/IEC 61725(1997)
Analytical expression for daily solar profiles
Jan 2010
20
IS 61730(Part 1):2004
Photovoltaic (PV) module safety qualification:
Part 1 Requirments for construction
Jan 2010
21
IS 61730(Part 2):2004
/ IEC 61730-2:2004
Photovoltaic (PV) module safety qualification:
Part 2 Requirments for testing
Feb 2010
22
IS 61829:1995
/ IEC 61829 : 1995
Crystalline silicon photovoltaic (PV) array - On site
measurment of I-V characteristics
Feb 2010
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 28(6415)
/ IEC 62108(2007-12)
Concentrator Photovoltaic (CPV) Modules And
Assemblies Design Qualification And Type Approval
2
DOC.ETD 28(6416)
/ IEC 62093 (2005)
Balance-Of-System Components For Photovoltaic
Systems - Design Qualification Natural Environments
3
DOC.ETD 28(6417)
/ IEC 62109-1(2010)
Safety Of Power Converters For Use in Photovoltaic
Power Systems - Part 1: General Requirements
4
DOC.ETD 28(6418)
/ IEC 62109-2 (2011)
Safety Of Power Converters For Use In Photovoltaic
Power Systems - Part 2: Particular Requirements For
Inverters
5
DOC.ETD 28(6419)
/ IEC 62124 (2010)
Photovoltaic (Pv) Stand-Alone Systems -Design
Verification
6
DOC.ETD 28(6495)
Led based solar lantern : Part 1 : Specifications
7
DOC.ETD 28(6496)
Led based solar lantern : Part 2: Methods of test
8
DOC.ETD 28(6554)
/ IEC 60904-5 (2011)
Photovoltaic Devices - Part 5 : Determination of the
equivalent cell temperature (ECT) of Photovoltaic (PV)
Devices by the open-circuit voltage method (First
Revision of IS 12762 (Part 5)
9
DOC.ETD 28(6555)
/ IEC 60904-10 (2010)
Photovoltaic Devices - Part 10 : Methods of Linearity
Measurement (First Revision of IS 12762 (Part 10)
10
DOC.ETD 28(6556)
/ IEC 61701 (1995)
Salt Mist Corrosion Testing of Photovoltaic (PV)
Modules (First Revision of IS/IEC 61701)
11
DOC.ETD 28(6557)
/ IEC 62116 (2008)
Test Procedure Of Islanding Prevention Measures for
Utility-Interconnected Photovoltaic Inverters
12
DOC.ETD 28(6559)
/ IEC 61345 (1998)
UV Test For Photovoltaic (PV) Modules
13
DOC.ETD 28(6560)
/ IEC 61853-1 (2011)
Photovoltaic (PV) Module Performance Testing And
Energy Rating - Part 1: Irradiance and temperature
performance measurements and power rating
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
79
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 28(6617)
/ IEC 62446 (2009)
Grid Connected Photovoltaic Systems - Minimum And
Requirements For System Documentation,
Commissioning Tests Inspection
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
80
ETD 29 POWER CAPACITORS
SCOPE - To prepare standards for power capacitors such as series and shunt
capacitors for power systems, self-healing and non-self-healing power
capacitors with metallized dielectric, ac motor capacitors,capacitors for
inductive heating plants,voltage grading capacitors,coupling
capacitors,energy storage capacitors etc.
NOTE - The standards for capacitors used in electronic circuits are excluded
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 1709:1984
| IEC 252:1975
Capacitors for electric fan motors (first revision)
2
IS 2993:1998
/ IEC 60252:1993
A.C. motor capacitors (second revision)
3
IS 9251:1979
| IEC 60110:1973
Capacitors for inductive heat generating plants
operating at frequencies between 40 and 24 000 Hz
4
IS 9348:1998
/ IEC 60358:1990
Coupling capacitor and capacitor dividers
5
IS 9835(Part 1):2001
/ IEC 60143-1:1992
Series capacitors for power systems:
Part 1 General performance testing and ratingSafety requirements - guide for installation (first
revision)
6
IS 9835(Part 3):2012
7
IS 11530:1985
| IEC 60358 :1990
8
IS 11548:1986
9
Mar 2011
2
Jul 2013
Mar 2011
1
Jul 2013
Jan 2011
Series capacitors for power systmes - Part 3 : Internal
fuses (IEC 60143-3:1998)
Voltage grading capacitor
Mar 2011
Capacitors for surge protection for use in
voltage system above 650 V and upto 33 kV
Mar 2011
IS 12672:1989
/ IEC 60593:1977
Internal fuses and internal overpressure
disconnectors for shunt capacitors
Mar 2011
10
IS 12677:1989
| IEC 60595:1977
Internal fuses for series capacitors
Mar 2011
11
IS 12730:1989
| IEC 60594:1977
Internal fuses and internal overpressure disconnectors
for capacitors for inductive heat generating plants
Mar 2011
12
IS 13203:1991
| IEC 60996:1989
Method for verifying accuracy of tan-delta
measuremnts
Mar 2011
13
IS 13340(Part 1):2012
Shunt capacitors for the self-healing type for ac power
systems having rated voltage upto and including 1 000
V - Part 1 General performance, testing and rating safety requirements - Guide for installation and
operation (first revision of IS 13340 (IEC 608311:2002)
14
IS 13340(Part 2):2012
Shunt capacitors of the self-healing type for ac
systems having a rated voltage upto and including 1
000 V - Part 2 Ageing test self-healing upto and
destruction test (first revision of IS 13341 (IEC 608312:1995)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
81
1
15
IS 13341:1992
| IEC 60831-2:1988
Requirements for ageing test, self-healing test and
destruction test on shunt capacitors of the self-healing
type for ac power systems having a rated voltage upto
and including 650 V
Apr 2008
16
IS 13580:1992
| IEC 60594:1977
Internal fuses and internal overpressure disconnectors
for power electronic capacitors
Apr 2013
17
IS 13585(Part 1):2012
| IEC 60931-1:1996
Shunt capacitors of the non-self-healing type for ac
systems having a rated voltage upto and including 1
000 V - Part 1 General - performance, - Guide for
installation and operation (first revision of IS 13585
(Part 1) (IEC 60931-1:1996)
18
IS 13585(Part 2):2012
Shunt capacitors of the non-self-healing type for ac
systems having a rated voltage upto and including 1
000 V - Part 2 Ageing test and destruction test (IEC
60931-2:1996)
19
IS 13585(Part 3):2012
Shunt capacitors of the non-self-healing type for ac
systems having a rated voltage upto and including 1
000 V - Part 3 Internal fuses (IEC 60931-3:1996)
20
21
IS 13648:1993
| IEC 61071-1:1991
IS 13666:1993
Power electronics capacitors
Apr 2013
Energy storage capacitors
Sep 2013
22
IS 13925(Part 1):2012
| IEC 60871-1:2005
Shunt capacitors for ac power systems having a rated
voltage above 1000 V : Part 1General performance,
testing and rating safety requirements - Guide for
installation and operation (superseding IS
2834:1986)(First Revision)
23
IS 13925(Part 2):2002
/ IEC60871-2:1999
Shunt capacitors for ac power systems having a rated
voltage above 1000 V : Part 2 Endurance testing (first
revision)
Mar 2012
24
IS 13925(Part 3):2002
/ IEC 60871-3:1996
Shunt capacitors for ac power systems having a rated
voltage above 1000 V: Part 3 Protection of shunt
capacitors and shunt capacitors banks.
Mar 2012
25
IS 13925(Part 4):2012
Shunt capacitors for AC power systems having a rated
voltage above1 000V - Part 4 Internal fusses (IEC
60871-4:2005
1
2
26
IS 15395:2003
/ IEC 61642 :1997
Industrial ac net- work affected by harmonicsapplication of filters and shunt capacitors
Oct 2013
27
IS 15406(Part 1):2003
/ IEC 61270-1:1996
Capacitors for microwave ovens: Part 1 General
Oct 2013
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 29(6508)
/ 60110-1:1998
Power capacitors for induction heating installations Part 1 : General (First revision of IS 9251)
2
DOC.ETD 29(6509)
/ 60110-2:2000
Power capacitors for induction heating installations Part 2 : Ageing test, destruction test and requirements
for disconnecting internal fusesl (First revision of IS
9251)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 29(6666)
Automatic Power Factor Correction (APFC) Panels for
Voltage Rating upto and including 1 000 V
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
82
#Error
2
DOC.ETD 29(6666)
Automatic power factor correction (APFC) Panels for
voltage rating upto and including 1 000 V
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
83
ETD 30 SURGE ARRESTERS
SCOPE - To prepare standards on surge arresters and their accessories, application
guide for surge arrestors for different locations
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
* IS 3070(Part 3):1993
| IEC 60099-4:1991
Lightning arresters for alternating current systems :
Part 3 Metal oxide surge-arresters without gaps
for ac systems
Apr 2014
2
IS 15086(Part 1):2001
/ IEC 60099-1:1991
Surge arresters: Part 1 Non-linear resistor type gapped
surge arresters for a.c. systems [Superseding IS
3070(Part 1)]
Jul 2011
3
IS 15086(Part 3):2003
| IEC 60099-3:1990
Surge arresters: Part 3 Artificial pollution testing of
surge arresters
Jul 2013
4
IS 15086(Part 5):2001
/ IEC 60099-5:1996
Surge arresters : Part 5 Selection and application
recommendations (Superseading IS 4004)
Jul 2011
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 30(6595)
Surge arresters Part 8 Metal oxide surge arresters with
external series gap (EGLA) for overhead transmission
and distribution lines of a.c. systems above 1 kV [IEC
60099-8(2011)]
2
DOC.ETD 30(6639)
Surge Arresters – Part 7: Glossary of terms and
definitions from IEC publications 60099-1, 60099-4,
60099-6, 61643-1, 61643-12, 61643-21, 61643-311,
61643-321, 61643-331 and 61643-341 ([IEC/PAS
60099-7(2004)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
84
1
ETD 31 POWER ELECTRONICS
SCOPE - To prepare standards regarding equipment and their components for
electronic power switching
NOTE 1 - Components which are comprised within the scope include
electronic devices
NOTE 2- The scope does not include telecommunication apparatus other
than convertors for power supplies to such apparatus, nor does it include
power supplies for electrical measurement
NOTE 3- The standards for inverters for photovoltaic energy systems are
excluded
NOTE 4- Converters for HVDC systems are excluded
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 2511:1963
| IEC 60119(1960)
Specification for Polycrystalline semiconductor rectifier
stacks
Mar 2011
2
IS 3136:1965
| IEC 60119(1960)
Specification for Polycrystalline semiconductor rectifier
equipment
Mar 2011
3
IS 3895:1966
| IEC 60146(1963)
Specification for Monocrystalline semiconductor
rectifier cells and stacks
Mar 2011
4
IS 4540:1968
| IEC 60146(1963)
Specification for Monocrystalline semiconductor
rectifier assemblies and equipment
Mar 2011
5
IS 6619:1972
Specification for Safety code for semiconductor
rectifier equipment
Mar 2011
6
IS 7204(Part 1):1974
Specification for Stabilized power supplies dc output:
Part 1 Terms and definitions .
Mar 2011
7
IS 7204(Part 2):1980
| IEC 60478-2(1975)
Specification for Stabilized power supplies dc output:
Part 2 Rating and performance .
Mar 2011
8
IS 7204(Part 3):1980
| IEC 60478-3(1976)
Specification for Stabilized power supplies dc
output: Part 3 Radio frequency interference tests
Mar 2011
9
IS 7204(Part 4):1980
| IEC 60478-4(1976)
Specification for Stabilized power
supplies dc
output: Part 4 Tests other than radio-frequency
interference.
Mar 2011
10
IS 7788:1975
| IEC 60411(1973)
Specification for Single-phase traction power
converters
Mar 2011
11
IS 11260(Part 1):1985
| IEC 60686(1980)
Specification for Stabilized power supplies ac output:
Part 1Ratings and performance .
Mar 2011
12
IS 11260(Part 2):1985
| IEC 60686 (1980)
Specification for Stabilized power supplies ac output:
Part 2 Tests
Mar 2011
Solid state invertors run from storage batteries Specification
Apr 2013
13
IS 13314:1992
14
IS 14256:1995
| IEC 61136-1(1992)
Rating specification for semiconductor power
converters for adjustable speed electric drive
systems - particularly for DC motor drives.
Mar 2010
15
IS 15199(Part 1):2002
/ IEC 61287-1(1995)
Power convertors: installed on board railway rolling
stock - Part 1 Characteristics and test methods
Sep 2012
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
85
2
16
IS 15199(Part 2):2002
/ IEC 61287-2(2001)
Power convertors: installed on board railway rolling
stock - Part 2 Additional technical information
Sep 2012
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 31(6127)
Uninterruptible power systems (UPS) :
Part 2 electromagnetic compatibility (EMC)
requirements
2
DOC.ETD 31(6432)
/ IEC 62040-1 (2008)
Uninterruptible power systems (UPS) : Part 1 General
and safety requirements,
3
DOC.ETD 31(6433)
/ IEC 62040-3 (2011)
Uninterruptible power systems (UPS) : Part 3 Method
of specifying the performance and test requirements
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 31(6719)
/ IEC 60146-1-1(2009)
Semiconductor converters General requirements and
line commuted converters Part 1-1: Specification of
basic requirements
2001
2
DOC.ETD 31(6720)
/ IEC 60146-1-3 (1991)
Semiconductor convertors General requirements and
line commutated convertors Part 1-3: Transformers
and reactors
2001
3
DOC.ETD 31(6721)
/ IEC 60146-2 (1999)
Semiconductor convertors – Part 2 Self commuted
semiconductor converters including direct d.c.
Converters
2001
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
86
ETD 32 ELECTRICAL APPLIANCES
SCOPE - To prepare standards for electrical appliances for household and similar
purpopses, including associated controls
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 302(Part 1):2008
| IEC 60335-1(2006)
Safety of household and similar electrical appliances:
Part 1 General requirements (sixth revision)
2
IS 302(Part 2/Sec 2):1997
| IEC 60335-2-2(1993)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 2 Vacuum
cleaners and water suction cleaning appliances
Mar 2014
1
3
IS 302(Part 2/Sec 3):2007
| IEC 60335-2-3(2002)
Safety of household and similar electric appliances:
Part 2 Particular requirements, Sec 3 Electric iron (first
revision)
Jun 2012
1
4
IS 302(Part 2/Sec 4):1993
| IEC 60335-2-4(1984)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 4 Spin
extractors
Mar 2014
1
5
IS 302(Part 2/Sec 6):2009
| IEC 60335-2-6(1986)
Safety of household and similar electrical appliances:
Part 2 Particuar requirements, Section 6 Cooking
ranges, cooking tables, ovens and similar appliances
(First Revision)
6
IS 302(Part 2/Sec 7):2009
| IEC 60335-2-7(1984)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 7 Domestic electric clothes washing machines
Mar 2014
2
7
IS 302(Part 2/Sec 8):1994
| IEC 60335-2-8(1987)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 8 Electric
shavers, hair clippers and similar appliances
Mar 2014
1
8
IS 302(Part 2/Sec 9):2009
| IEC 60335-2-9(1986)
Safety of household and similar electrical appliances:
Part 2 Particular requirements: Section 9 Electric
toasters, grills, roastors and similar appliances (First
Revision)
9
IS 302(Part 2/Sec 11):1994
| IEC 60335-2-11(1976)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 11 Tumbler
dryers
Mar 2014
1
10
IS 302(Part 2/Sec 12):1993
| IEC60335-2-12(1987)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 12 Warming plates and similar appliances
Mar 2014
1
11
IS 302(Part 2/Sec 13):1994
| IEC 60335-2-13(1987)
Safety of household and similar electrical appliances
:Part 2 particular requirements, Section 13 Frying
pans, deep fat fryers and similar appliances
Mar 2014
1
12
IS 302(Part 2/Sec 14):2009
| IEC 60335-2-14(1984)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,Section 14 Electric
kitchen machines (First Revision)
13
IS 302(Part 2/Sec 15):2009
| IEC 60335-2-15(1986)
Safety of household and similar electrical appliances:
Part 2 Particular requirements: Section 15 Appliances
for heating liquids (First Revision)
14
IS 302(Part 2/Sec 21):2011
| IEC 60335-2-21(1989)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 21 Stationary storage type electric water
heater (First Revision
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
87
2
15
IS 302(Part 2/Sec 23):2009
| IEC 60335-2-23(1986)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 23 Appliances
for skin and hair care (First Revision)
16
IS 302(Part 2/Sec 24):1994
| IEC 60335-2-24(1992)
Safety of household and similar electrical
appliances:Part 2 Particular requirements,
Sec 24 Refrigerators, food freezers and ice makers
Mar 2014
17
* IS 302(Part 2/Sec 25):1994
| IEC 60335-2-25(1988)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 25 Microwave ovens
Mar 2014
1
18
IS 302(Part 2/Sec 26):1994
| IEC 60335-2-26(1987)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 26 Clocks
Mar 2014
1
19
IS 302(Part 2/Sec 30):2007
| IEC 60335-2-30(2002)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 30 Room heaters (first revision)
Aug 2012
1
20
IS 302(Part 2/Sec 31):2009
| IEC 60335-2-31 2002)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 31 Range
Hoods
21
IS 302(Part 2/Sec 32):1994
| IEC 60335-2-32(1993)
Safety of household and similar electrical appliances:
Part 2 Particular requirements:
Section 32 Massage appliances
Mar 2014
1
22
IS 302(Part 2/Sec 35):2011
| IEC 60335-2-35(1991)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 35 Electric
instantaneous water heater(First Revision
23
IS 302(Part 2/Sec 45):1994
| IEC 60335-2-45(1986)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Sec 45 Electric heating tools
Mar 2014
24
IS 302(Part 2/Sec 46):1993
| IEC 60335-2-46(1986)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 46 Electric steam cookers
Mar 2014
25
IS 302(Part 2/Sec 59):1999
| IEC 60335-2-59(1990)
Safety of household and similar electrical appliances : Mar 2014
Part 2 Particular requirements , Section 59 Insect killers
26
IS 302(Part 2/Sec 76):1999
| IEC 60335-2-76(1997)
Safety of household and similar electrical appliances
Part 2 Particular requirements,
Section 76 Electric fence energizers
Mar 2014
27
* IS 302(Part 2/Sec 80):2003
| IEC 60335-2-80
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Sec 80 Fans
(Superseding IS 12155:1987)
Sep 2013
28
IS 302(Part 2/Sec 201):2008
| IEC 60335-2-74(2002)
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 201 Electric immersion water heaters
(first revision)
May 2013
1
29
IS 302(Part 2/Sec 202):1992
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Section 202 Electric stoves
Mar 2014
2
30
IS 302(Part 2/Sec 203):1994
Safety of household and similar electrical appliances:
Part 2 Particular requirements:
Section 203 Electric call bells and buzzers for indoor
use
Mar 2014
1
31
IS 302(Part 2/Sec 204):1994
Safety of household and similar electrical appliances:
Part 2 Particular requirements:
Section 204 Electric water boilers
Mar 2014
1
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
88
1
1
32
IS 302(Part 2/Sec 206):1994
Safety of household and similar electrical appliances:
Part 2 Particular requirements:
Section 206 Electric coffee machines
Mar 2014
1
33
IS 302(Part 2/Sec 207):1994
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Sec 207 Electric hot plates
Mar 2014
1
34
IS 302(Part 2/Sec 208):1994
Safety of household and similar electrical appliances:
Part 2 Particular requirements,
Sec 208 Single walled baking ovens
Mar 2014
1
35
IS 302(Part 2/Sec 209):1996
Safety of household and similar electrical appliance:
Part 2 Particular requirements ,
Section 209 Portable low speed food grinding
machines
Jul 2010
3
36
IS 365:1983
| IEC 60302-2-6(1982)
Electric hot plates (second revision)
Mar 2014
3
37
* IS 366:1991
| IEC 60311(1988)
Electric irons (fourth revision)
Apr 2013
6
38
IS 367:1993
| IEC 60530(1975)
Electric kettles and jugs for household
and similar use (fourth revision)
Mar 2014
39
* IS 368:1992
Electric immersion water heaters (fourth revision)
Mar 2014
1
40
* IS 369:1992
| IEC 60675
Electric radiators (third revision)
Feb 2011
2
41
* IS 374:1979
Electric ceiling type fans and regulators (third revision)
Sep 2010
7
42
* IS 555:1979
Electric table type fans and regulators (third revision)
Jul 2010
2
43
IS 959:1994
Electric soldering irons (second revision)
Mar 2014
44
* IS 1169:1967
Electric pedestal type fans and regulators
(first revision)
Mar 2014
45
IS 1287:1993
| IEC 60442(1973)
Electric toasters (third revision)
Mar 2014
46
IS 1401:2008
/ IEC 61032 : 1997
Protection of persons and equipment by enclosures Probes for verification (second revision)
Apr 2013
Electric hand lamps (revised)
Aug 2011
2
Stationary storage type electric water heaters (fourth
revision)
Nov 2009
5
Electric call bells and buzzers for indoor use
(second revision)
Mar 2014
47
48
49
50
IS 1415:1966
* IS 2082:1993
| IEC 60379(1982)
IS 2268:1994
* IS 2312:1967
| IEC 60665(1981)
Propeller type ac ventilating fans (first revision)
51
IS 2994:1992
Electric stoves (second revision)
52
IS 2997:1964
Air circulator type electric fans and regulators
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
89
Jul 2010
6
8
Mar 2014
Jul 2010
8
53
IS 3017:1985
| IEC 60730(1982)
Thermostats for use with electric water heaters (first
revision)
Aug 2011
5
54
IS 3412:1994
Electric water boilers (second revision)
Mar 2014
55
IS 3481:1966
Electric portable lamp stands and brackets
Mar 2014
5
56
IS 3588:1987
Electric axial flow fans (first revision)
Aug 2009
1
57
IS 3724:1966
Cartridge type heating elements (non-embedded type) Aug 2011
4
58
* IS 3725:1966
Resistance wires, tapes and strips for heating elements Jan 2011
3
59
IS 3963:1987
Roof extractor units (first revision)
Aug 2009
1
60
IS 4158:1985
Solid embedded type electric heating elements
(first revision)
Aug 2011
4
2
61
IS 4159:2002
| IEC 60335-2-73(1994)
Mineral filled sheathed heating elements
(third revision)
Mar 2012
62
IS 4165:1991
| IEC 60730(1982)
Thermostats for general purpose electric ovens
(first revision)
Aug 2011
Domestic Electric food mixers (liquidizers and
grinders) and Centrifugal Juicers (first revision)
Dec 2009
9
Hot air fans (first revision)
Aug 2009
3
4
63
IS 4250:1980
64
* IS 4283:1981
65
IS 4327:1967
Electric fans and regulators for use in ships
Aug 2009
66
IS 4894:1987
Centrifugal fans (first revision)
Aug 2009
67
IS 5159:1969
Mains-operated electric shavers
Aug 2011
2
68
IS 5161:1969
Flexible electric heating pads for domestic use
Aug 2011
4
69
IS 5579:1985
Neon testers (first revision)
Aug 2011
1
70
IS 5790:1985
| IEC 60350
Domestic electric cooking ovens (first revision)
Sep 2009
3
71
IS 6272:1987
Industrial cooling fans (man coolers) (first revision)
Aug 2009
2
Steam irons (first revision)
Aug 2011
5
5
72
IS 6290:1986
| IEC 60311(1970)
73
IS 6365:1971
Laboratory electric ovens
Aug 2011
74
IS 6390(Part 2):1992
Domestic electrical clothes washing machines:
Part 2 Requirements for tumbler dryers
Mar 2014
75
IS 6446:1986
Mica insulated heating elements (first revision)
Dec 2009
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
90
5
76
IS 6680:1992
| IEC 60342-1
Railway carriage fans (first revision)
Aug 2009
77
IS 7137:1973
Portable, hand held mains-operated electric
massagers
Aug 2011
2
78
IS 7154:1994
Mains-operated electric hair-dryers (first revision)
Mar 2014
1
79
IS 7603:1975
Low speed food grinding machines
Jul 2010
3
80
IS 8506:1977
Laboratory electric resistance furnaces
Aug 2011
81
IS 8978:1992
Electric instantaneous water heaters (second
revision)
Dec 2009
2
82
IS 8985:1978
Single walled baking ovens
Aug 2011
1
Electric frying pans and deep fat fryers
Apr 2013
2
Electric gas lighters
Aug 2011
1
Microwave ovens for household and similar purposes
Aug 2011
Electric steam cookers
Aug 2011
Hand held electric engraving tools
Mar 2014
83
IS 10436:1983
| IEC 60335-2-13
84
IS 10975:1984
85
IS 11676:1995
| IEC 60705(1988)
86
IS 11879:1986
87
IS 12289:1988
| IEC 60745-1
88
IS 13231:1991
Warming plates
Aug 2011
89
IS 13368:1992
Method of test for double inlet
centrifugal fans (industrial type)
Aug 2009
2
90
IS 13588:1993
/ IEC 60817(1984)
Spring operated impact test apparatus and calibration
Mar 2014
91
IS 13886:1993
| IEC 60730(1892)
Bimetallic thermostats and thermal
cutouts for use with electric irons
Mar 2014
92
IS 14144:1994
| IEC 60661(1980)
Electric coffee makers
(Superseding IS 3514)
Mar 2014
93
IS 14145:1994
Mains operated clocks
(superseding IS 5160)
Apr 2013
94
IS 14155:1994
| IEC 60456(1974)
Domestic electric clothes washing machines
for domestic use [Superseding IS 6390(Part 1):1983
and IS 6390 (Part 3): 1992]
Mar 2014
1
95
IS 15644:2006
/ IEC 62115(2003)
Safety of electric toys
Aug 2011
1
96
IS 60730(Part 1):1999
/ IEC 60730-1 : 1999
Automatic electrical controls for household and similar
use: Part 1 General requirements
May 2013
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 32(6618)
Cartridge type heating elements (non-embedded
type) (First Revision of IS 3724)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
91
1
2
DOC.ETD 32(6325)
Automatic electric controls for household and similar
use Part 2 Particular requirements for temperature
sensing controls
3
DOC.ETD 32(6442)
Specification for electric immersion water heaters (fifth
revision of IS 368)
4
DOC.ETD 32(6592)
Safety of Household and Similar Electrical Appliances
Part 2 Particular Requirements Section 25 Microwave
Ovens, Including Combination Microwave Ovens
(First Revision of IS 302-2-25)
5
DOC.ETD 32(6605)
Safety of household and similar electrical appliances:
Part 2 Particular requirements, Section 26 Clocks
(First Revision of IS 302-2-26)
DRAFT STANDARDS FINALIZED BUT NOT YET UNDER PRINT
1
DOC.ETD 32(6408)
Household and similar electrical appliances : Part 1
General requirements (IEC 60335-1)
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 32(6477)
Household electric direct-acting room heaters Performance requirements (Fourth Revision of IS 369)
2
DOC.ETD 32(6581)
Stationary storage type electric water heaters (fifth
revision of IS 2082)
3
DOC.ETD 32(6593)
Electri ceiling type fans and regulators - Specification
(fourth revision of IS 374)
4
DOC.ETD 32(6594)
Household and similar electrical appliances - Safety Part 2-80: Particular requirements for fans (First
Revision)
DRAFT STANDARDS FORMULATED
1
DOC.ETD 32(6619)
Mineral filled sheathed heating elements
(fourth revision of IS 4159)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
92
2001
ETD 33 WINDING WIRES
SCOPE - To prepare standards for wires for electrical winding irrrespective of
conductor material, shape or type of covering taking into account the needs
in the fields of electrotechnology
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 482:1981
Reels for covered round electrical winding wires (third
revision)
Feb 2010
2
IS 2069:1991
Drums for covered winding wires and strips for
electrical purpose (second revision)
Feb 2010
3
IS 4685(Part 1):1968
Varnish bonded glass-fibre covered copper
conductors: Part 1 Round wires
Feb 2010
1
4
IS 5825:1993
/ IEC 60172(1987)
Test procedure for the determination of the
temperature index of enamelled winding wires (first
revision)
Jun 2013
5
IS 6162(Part 1):1971
| IEC 60111
Paper covered aluminium conductors : Part 1 Round
conductors
Jun 2013
4
6
IS 6162(Part 2):1971
| IEC 60111
Paper covered aluminium conductors:Part 2
Rectangular conductors
Jun 2013
5
Varnish bonded glass-fibre braided rectangular
copper conductors
Jun 2013
1
Cotton covered copper conductors : Part 1 Round
conductors
Jun 2013
2
7
IS 6181:1971
8
IS 7391(Part 1):1974
| IEC 60182
9
IS 7391(Part 2):1974
Cotton covered copper conductors : Part 2
Rectangular conductors (superseeding IS:2068)
Jun 2013
10
IS 7404(Part 1):1991
Paper covered copper conductors : Part 1 Round
conductors [superseeding IS:3454) (first revision)
Feb 2010
Bunched enamelled copper conductors with silk
covering
Jun 2013
11
IS 7576:1974
| IEC 60317-1
12
IS 8572:1993
Paper covered flexible/stranded copper conductors for
transformer leads (first revision)
Jun 2013
13
IS 8783(Part 1):1995
Winding wires for submersible motors Part 1:
Conductor data (first revision)
Feb 2010
1
14
IS 8783(Part 2):1995
Winding wires for submersible motors Part 2: Materials
for dielectric and jacket (first revision)
Feb 2010
1
15
IS 8783(Part 3):1995
Winding wires for submersible motors Part 3: Methods
of tests (first revision)
Feb 2010
2
16
IS 8783(Part 4/Sec 1):1995
Winding wires for submersible motors Part 4:
Specifications for individual wires, Section 1 HR PVC
insulated wires (first revision)
Feb 2010
1
17
IS 8783(Part 4/Sec 2):1995
Winding wires for submersible motors Part 4:
Specifications for individual wires,Section 2
Crosslinked polyethylene insulated and polyamide
jacketed wires (first revision)
Feb 2010
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
93
18
IS 8783(Part 4/Sec 3):1995
Winding wires for submersible motors Part 4:
Specifications for individual wires, Section 3 Polyester
and polypropylene insulated winding wires (first
revision)
Feb 2010
1
19
IS 9148:1979
Tape wrapped rectangular and square copper wires
with a temperature index of 220
Feb 2010
1
20
IS 9778:1981
Guide for evaluation of thermal endurance of varnish
bonded glass-fibre covered rectangular copper
conductors
Feb 2010
1
Taper barrelled delivery spools for covered round
electrical winding wires
Feb 2010
21
IS 10031:1981
| IEC 60264-3(1973)
22
IS 11174:1984
Aromatic polyamide paper covered rectangular and
square copper wires with temperature index 200
Feb 2010
23
IS 11184:1984
Enamelled and varnish bonded glass fibre covered
round copper wires
Feb 2010
24
IS 11395:1985
Tape wrapped round copper wires with temperature
index of 220
Feb 2010
25
IS 11597:1986
Polyester tape wrapped, varnish bonded glass-fibre
covered rectangular paper conductors
Feb 2010
26
IS 13343:1992
Guide for evaluation of thermal endurance of
enamelled and varnish bonded glass covered copper
conductors
Aug 2013
27
IS 13730:2012
/ IEC 60317-0-1:2008
Specifications for particular types of winding wires:
Part 0 General requirements, Section 1 Enamelled
round copper wire (First Revision)
28
IS 13730(Part 0/Sec 2):2011
/ IEC 60317-0-2:2005
Specifications for particular types of winding wires:
Part 0 General requirements, Section 2 Enamelled
rectangular copper wire (First Revision)
29
IS 13730:2012
/ IEC 60317-0-3:2008
Specifications for particular types of winding wires Part
0-3: General requirements – Enamelled round
aluminium wire [First Revision of IS 13730 (Part
0/Sec 3):1994] I
30
IS 13730(Part 0/Sec 4):2011
/ IEC 60317-0-4:2006
Specifications for particular types of winding wires:
Part 0 General requirements, Section 4 Glass fibre
wound resin of varnish impregnated bare or
enamelled rectangular copper wire (First Revision)
31
IS 13730(Part 0/Sec 5):2012
/ IEC 60317-0-5(2006)
Specifications for particular types of winding wires:
Part 0 General requirements, Section 5 glass fibre
braided, bare or enamelled rectangular copper wire
(First Revision)
32
IS 13730:2012
Speciication for particular types of winding wires Part 06 : General requirements Glass-fibre wound resin or
varnish impregnated, bare or enamelled round copper
wire
33
IS 13730(Part 1):1993
/ IEC 60317-1(1990)
Specifications for particular types of winding wires:
Part 1 Polyvinyl acetal enamelled round copper wire,
class 105 [superseeds IS 4800(Part 4):1968]
34
IS 13730(Part 2):2012
/ IEC 60317-2 : 2000
Specifications for particular types of winding wires Part
2: Solderable polyurethane enamlled round copper
wire, class 130, with a bonding layer. (First Revision)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
94
1
#Error
Jun 2013
35
IS 13730(Part 3):2013
/ IEC 60317-3:2004
Specifications for particular types of winding wires Part
3 polyester enamelled round copper wire, class 155
(first revision)
36
IS 13730(Part 4):2013
/ IEC 60317-4(1990)
Specifications for particular types of winding wires:
Part 4 Solderable polyurethane enamelled round
copper wire, class 130 (first revision)
37
IS 13730(Part 6):1994
38
Specifications for particular types of winding wires :
Part 6 Oleo-resinous enamelled round aluminium wire,
Class 180 [Superseeds IS 4800(Part 7):1970]
Feb 2010
IS 13730(Part 7):1993
/ IEC 60317-7(1990)
Specifications for particular types of winding wiresC
Part 7 Polyimide enamelled round copper wire Class
220 [superseeds IS 4800(Part 11):1981]
Jun 2013
39
IS 13730(Part 8):1996
/ IEC 60317-8(1990)
Specifications for particular types of winding wires:
Part 8 polyesterimide enamelled round copper wire
class 180
Dec 2013
40
IS 13730(Part 9):1994
Specifications for particular types of winding wires
:Part 09 Polyester enamelled round aluminium wire,
Class 130
Feb 2010
41
IS 13730(Part 12):2012
/ IEC 60317-12:2010
Specifications for particular types of winding wires Part
12: Polyvinyl acetal enamelled round copper wire,
class 120
42
IS 13730(Part 13):2014
/ IEC 60317-13(1990)
Specifications for particular types of winding wires:
Part 13 Polyester or polyesterimide overcoated with
polyamide-imide enamelled round copper wire, Class
200
Jun 2013
43
IS 13730(Part 15):1994
Specifications for particular types of winding wires :
Part 15 Polyesterimide enamelled round aluminium
wire, Class 180
Feb 2010
44
IS 13730(Part 16):1996
/ IEC 60317-16 (1990)
Specifications for particular types of winding wires:
Part 16 Polyester enamelled rectangular copper wire,
Class 155
Dec 2011
45
IS 13730(Part 17):2014
/ IEC 60317-17 (1990)
Specifications for particular types of winding wires:
Part 17 Polyvinyl acetal enamelled rectangular copper
wire, Class 105
Dec 2011
46
IS 13730(Part 20):2014
/ IEC 60317-20(1990)
Specifications for particular types of winding wires:
Part 20 Solderable polyurethane enamelled round
copper wire, Class 155
Jun 2013
47
IS 13730(Part 26):1996
/ IEC 60317-26 (1990)
Specifications for particular types of winding wires:
Part 26 Polyamide-imide enamelled round copper
wire, Class 200
Jun 2013
48
IS 13730(Part 27):1997
/ IEC 60317-27(1990)
Specifications for particular types of winding wires:
Part 27 Paper covered rectangular copper wire
Jun 2013
49
IS 13730(Part 28):1997
/ IEC 60317-28(1990)
Specifications for particular types of winding wires:
Part 28 Polyesterimide enamelled rectangular copper
wire, Class 180
Jun 2013
1
50
IS 13730(Part 29):1996
/ IEC 60317-29(1990)
Specifications for particular types of winding wires:
Part 29 Polyester or polyesterimide overcoated with
polyamide-imide enamelled rectangular copper wire,
Class 200
Jun 2013
1
51
IS 13730(Part 31):1997
/ IEC 60317-31(1990)
Specifications for particular types of winding wires:
Part 31 Glass-fibre wound, polyester or polyesterimide
varnish- treated, bare or enamelled rectangular copper
wire, temperature index 180
Jun 2013
1
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
95
1
1
52
IS 13730(Part 32):1997
/ IEC 60317-32(1990)
Specifications for particular types of winding wires:
Part 32 Glass-fibre wound, polyester or polyesterimide
varnish-treated, bare or enamelled rectangular copper
wire, temperature index 155
Jun 2013
53
IS 13730(Part 33):1997
/ IEC 60317-33 (1990)
Specifications for particular types of winding wieres:
Part 33 Glass-fibre wound, silicone varnish-treated
bare or enamelled rectangular copper wire,
temperature index 200
Jun 2013
54
IS 13730(Part 34):2000
/ IEC 60317-34(1997)
Specifications for particular types of winding wires:
Part 34 Polyester enamelled round copper wire, Class
130 (first revision)
Feb 2010
55
IS 13730(Part 39):2005
/ IEC 60317-39:1992
Specifications for particular types of wires: Part 39
Glass-fibre braided polyester or polyesterimide varnishtreated, bare or enamelled rectrangular copper wire,
temperature index 180
Oct 2010
56
IS 13730(Part 43):2013
/ IEC 60317-43:1997
Specifications for particular types of wires: Part 43
Aromatic polyimide tape wrapped round copper wire,
class 240 (first revision)
57
IS 13730(Part 44):2013
/ IEC 60317-44:1997
Specifications for particular types of wires: Part 44
Aromatic polyimide tape rapped rectangular copper
wire, class 240 (first revision)
58
IS 13730(Part 45):1999
59
IS 13730(Part 48):2005
/ IEC 60317-48:1999
Specifications for particular types of wires: Part 48
Oct 2010
Glass fibre wound resin or varnish impregnated bare
or enamelled round copper wire, temperature index 155
60
IS 13730(Part 49):2005
/ IEC 60317-49:1999
Specifications for particular types of wires: Part 49
Oct 2010
Glass fibre wound resin or varnish impregnated bare
or enamelled round copper wire, temperature index 180
61
IS 13730(Part 50):2005
/ IEC 60317-50:1999
Specifications for particular types of wires: Part 50
Oct 2010
Glass fibre wound resin or varnish impregnated bare
or enamelled round copper wire, temperature index 200
62
IS 13730(Part 53):2005
/ IEC 60317-53:1999
Specifications for particular types of wires: Part 53
Aromatic polyamide (aramid ) tape wrapped
rectangular copper wire, temperature index 220
63
IS 13778(Part 1):2011
/ IEC 60851-1:1996
Methods of tests for winding wires: Part 1 General
(First Revision)
64
IS 13778(Part 2):2013
/ IEC 60851-2:2009
Methods of tests for winding wires: Part 2
Determination of dimensions (First Revision)
65
IS 13778(Part 3):2012
/ IEC 60851-3:2009
Winding wires – Test methods - Part 3: Mechanical
properties [First Revision of IS 13778 (Part 3)
66
IS 13778(Part 4):2011
/ IEC 60851-4:2005
Methods of tests for winding wires: Part 4 Chemical
properties
67
IS 13778(Part 5):2012
/ IEC 60851-5 : 2008
Winding wires – Test methods - Part 5: Electrical
properties [First Revision of IS 13778 (Part 5)
68
IS 13778(Part 6):2011
/ IEC 60851-6:1996
Methods of tests for winding wires: Part 6 Thermal
properties (First Revision)
69
IS 14841(Part 2/Sec 1):2000
/ IEC 60264-2-1:1989
Packaging of winding wires: Part 2 Cylindrical barrelled
delivery spools Section 1 Basic dimensions
Specifications for particular type of winding wires : Part
45 Polyester enamelled round copper wire , class 130
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
96
1
Mar 2014
Oct 2010
1
2
1
Feb 2010
70
IS 14841(Part 2/Sec 2):2000
/ IEC 60264-2-2:1990
Packaging of winding wires: Part 2 Cylindrical barrelled
delivery spools, Section 2 Specification for returnable
spools made from thermoplastic material
Feb 2010
71
IS 14841(Part 3/Sec 1):2000
/ IEC 60264-3-1:1999
Packaging of winding wires: Part 3 Taper barrelled
delivery spools, Section 1 basic dimensions
Feb 2010
72
IS 14841(Part 3/Sec 2):2000
/ IEC 60264-3-2:1999
Packaging of winding wires: Part 3 Taper barrelled
delivery spools, Section 2 Specification for returnable
spools made from thermoplastic material
Feb 2010
73
IS 14841(Part 3/Sec 3):2000
/ IEC 60264-3-3:1990
Packaging of winding wires: Part 3 Taper barrelled
delivery spools, Section 3 Specification for nonreturnable spools made from thermoplastic material
Feb 2010
74
IS 14841(Part 3/Sec 4):2000
/ IEC 60264-3-4:1999
Packaging of winding wires: Part 3 Taper barrelled
delivery spools, Section 4 basic dimensions of
containers for taper barrelled delivery spools
Feb 2010
75
IS 14841(Part 4/Sec 1):2013
/ IEC 60264-4-1:1997
Packaging of winding wires: Part 4 Methods of test,
Section 1 Delivery spools made from thermoplastic
material (first revision)
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 33(6373)
Packaging of winding wires – Part 3-1: Taper barrelled
delivery spools – Basic dimensions
2
DOC.ETD 33(6377)
Specifications for particular types of winding wires –
Part 8: Polyesterimide enamelled round copper wire,
class 180
3
DOC.ETD 33(6441)
/ 60315-25:2010
Specifications for particular types of winding wires Part 25 : Po0lyester or polyesterimide over coated with
polyamide-imide enamelled round aluminium wire
class 200
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
97
ETD 34 INSTRUMENTS TRANSFORMERS
SCOPE - To prepare standards and application guides for instrument transformers
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 2705(Part 1):1992
| IEC 60185(1966)
Current transformers: Part 1 General requirements
(second revision)
Aug 2012
2
IS 2705(Part 2):1992
| IEC 60185(1966)
Current transformers: Part 2 Measuring current
transformers (second revision)
Aug 2012
3
IS 2705(Part 3):1992
| IEC 60185(1966)
Current transformers: Part 3 Protective current
transformers (second revision)
Aug 2012
4
IS 2705(Part 4):1992
| IEC 60185(1966)
Current transformers: Part 4 Protective current
transformers for special purpose applications (second
revision)
Aug 2012
5
IS 3156(Part 1):1992
| IEC 60186(1987)
Voltage transformers: Part 1 General requirements
(second revision)
Aug 2012
6
IS 3156(Part 2):1992
| IEC 60186(1987)
Voltage transformers: Part 2 Measuring voltage
transformers (second revision)
Aug 2012
7
IS 3156(Part 3):1992
| IEC 60186(1987)
Voltage transformers: Part 3 Protective voltage
transformers (second revision)
Aug 2012
8
IS 3156(Part 4):1992
| IEC 60186(1987)
Voltage transformers: Part 4 Capacitor voltage
transformers (second revision)
Aug 2012
9
IS 4146:1983
Application guide for voltage transformers (first
revision)
Sep 2011
10
IS 4201:1983
Application guide for current transformers (first
revision)
Sep 2011
11
IS 5547:1983
Application guide for capacitor voltage transformers
(first revision)
Sep 2011
12
IS 6949:1973
Summation current transformers
Sep 2011
13
IS 11322:1985
| IEC 44-4 (1980)
Method for partial discharge measurement in
instrument transformers
Sep 2011
14
IS 16227(Part 1):2014
Instrument Transformers Part 1 : General
Requirements
15
IS 16227(Part 3):2014
Instrument Transformers Part 3 : Additional
Requirements for Inductive Voltage Transformers
16
IS 16227(Part 5):2014
Instrument Transformers Part 5 : Additional
Requirements for Capacitors Voltage Transformers
17
IS 60044(Part 1):2003
/ IS/IEC 60044-1(2003)
Instrument transformers: Part 1 Current transformers
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
98
Aug 2012
1
1
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 34(6320)
/ IEC 60040-3 (2002)
Instrument Transformers. Part 3 Combined
Transformers
2
DOC.ETD 34(6323)
/ IEC 60040-7 (2002)
Instrument Transformers. Part 7 Electronic Voltage
Transformers
3
DOC.ETD 34(6324)
/ IEC 60040-8 (2002)
Instrument Transformers.Part 8 Electronic Current
Transformers
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 34(6685)
/ IEC 61869-2 (2012)
Instrument Transformers Part 2 Additional
requirements for Current Transformers
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
99
ETD 35 POWER SYSTEM RELAYS
SCOPE - To prepare standards for power systems relays including those
incorporating solid state devices, also taking into account combination of
relays and devices to form schemes for power systems including control
equipment associated with that protection
NOTE - Relays used in electronic equipment are excluded
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 3231(Part 0):1986
Electrical relays for power system protection: Part 0
General introduction and list of parts (first revision)
Feb 2014
2
IS 3231(Part 1/Sec 1):1986
Electrical relays for power system protection: Part 1
General requirements, Section 1 Contact performance
(first revision)
Sep 2011
3
IS 3231(Part 1/Sec 2):1986
Electrical relays for power system protection: Part 1
General requirements, Section 2 Insulation tests (first
revision)
Sep 2011
4
IS 3231(Part 1/Sec 3):1986
| IEC 255-4 (1976)
Electrical relays for power system protection: Part 1
General requirements, Section 3 High frequency
disturbance test for static relays (first revision)
Sep 2011
5
IS 3231(Part 2/Sec 1):1987
| IEC 255-1-00
Electrical relays for power system protection: Part 2
Requirements for principal families, Section 1 All or
nothing relays
Sep 2011
6
IS 3231(Part 2/Sec 2):1987
Electrical relays for power system protection: Part 2
Requirements for principal families, Section 2 General
requirements for measuring relays
Sep 2011
7
IS 3231(Part 2/Sec 3):1987
| IEC 255-8 (1978)
Electrical relays for power system protection: Part 2
Requirements for principal families, Section 3 General
requirements for thermal relays
Sep 2011
8
IS 3231(Part 3/Sec 1):1987
| IEC 255-3 (1971)
Electrical relays for power system protection: Part 3
Requirements for particular group of relays, Section 1
Non-specified time or independent specified time
measuring relays
Sep 2011
9
IS 3231(Part 3/Sec 2):1987
| IEC 255-4 (1976)
Electrical relays for power system protection: Part 3
Requirements for particular group of relays, Section 2
Dependent specified time measuring relays
Sep 2011
10
IS 3231(Part 3/Sec 3):1987
| IEC 255-13(1980)
Electrical relays for power system protection:Part 3
Requirements for particular group of relays, Section 3
Biased (percentage) differential relays
Sep 2011
11
IS 3231(Part 3/Sec 4):1987
| IEC 255-12 (1980)
Electrical relays for power system protection: Part 3
Requirements for particular group of relays, Section 4
Directional relays and power relays
Sep 2011
12
IS 3231(Part 3/Sec 5):1987
| IEC255-16 (1982)
Electrical relays for power system Protection: Part 3
Requirements for particular group of relays, Section 5
Impedance measuring relays
Sep 2011
1
13
IS 3637:1966
Gas operated relays
Sep 2011
1
14
IS 3638:1966
Application guide for gas operated relays
Sep 2011
1
15
IS 3842(Part 1):1967
Application guide for electrical relays for ac systems:
Part 1 Overcurrent relays for feeders and transformers
Sep 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
100
16
IS 3842(Part 2):1966
Application guide for electrical relays for ac systems:
Part 2 Overcurrent relays for generators and motors
Sep 2011
17
IS 3842(Part 3):1966
Application guide for electrical relays for ac systems:
Part 3 Phase unbalance relays including negative
phase sequence relays
Sep 2011
1
18
IS 3842(Part 4):1966
Application guide for electrical relays for ac systems:
Part 4 Thermal relays
Sep 2011
1
19
IS 3842(Part 5):1968
Application guide for electrical relays for ac systems:
Part 5 Distance protection relays
Sep 2011
20
IS 3842(Part 6):1972
Application guide for electrical relays for ac systems:
Part 6 Power relays
Sep 2011
21
IS 3842(Part 7):1972
Application guide for electrical relays for ac systems:
Part 7 Frequency relays
Sep 2011
22
IS 3842(Part 8):1976
Application guide for electrical relays for ac systems:
Part 8 Voltage relays
Sep 2011
23
IS 3842(Part 9):1977
Application guide for electrical relays for ac systems:
Part 9 Relays for busbar protection
Sep 2011
24
IS 3842(Part 10):1976
Application guide for electrical relays for ac systems:
Part 10 Relays for transverse differential protection
Sep 2011
25
IS 3842(Part 12):1976
Application guide for electrical relays for ac systems:
Part 12 Differential relays for transformers
Sep 2011
26
IS 4483(Part 1):1968
Preferred panel cutout dimensions for electrical relays:
Part 1 Flush mounting IDMTL relays
Sep 2011
27
IS 5834(Part 1):1994
Electrical timer relays for industrial purposes (Part 1)
Pneumatic (First revision)
Feb 2014
28
IS 5834(Part 2):1993
Electrical timer relays for industrial purposes (Part 2)
Motorized (first revision)
Apr 2013
1
29
IS 5834(Part 3):1981
Electrical timer relays for industrial purposes (Part 3)
Electronic
Feb 2014
2
Static protective relays
Sep 2011
30
IS 8686:1977
| IEC 255-4
31
IS 8714:1978
Electrical protective relays for use in siesmic areas
Sep 2011
32
IS 9124:1979
Guide for maintenance and field testing of electrical
relays
Sep 2011
33
IS 9994:1981
Potential relays for capacitor start-capacitor run
hermetic compressors
Sep 2011
34
IS 10075:1981
Start relay and overload protector for resistance start
induction run hermetic compressors
Sep 2011
35
IS 12083(Part 1):1986
| IEC 255-0-20 (1974)
Electrical relays: Part 1 Contact performance
Sep 2011
36
IS 12083(Part 2):1986
| IEC 255-5 (1977)
Electrical relays: Part 2 Insulation tests
Sep 2011
37
IS 14122:1994
| IEC 60034-11(1978)
Built in thermal protection for electric motors rated up
to 660 V ac
Sep 2011
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
101
1
38
ISQC 160000 : 1988
/ IECQC 60255-7:1978
Electrical relays:Part 1 tests and measurement
procedures for electromechanical all-or-nothing relays
Feb 2014
39
ISQC 160000 : 1988
/ IECQC 60255-10:1979
Electrical relays:Part 2 Applications of the IEC quality
assessment systems for electronic components to allor-nothing relays
Feb 2014
40
ISQC 160100 : 1988
/ IECQC 160100:1983
Electrical relays, sectional specification:
Electromechanical all-or-nothing relays of assessed
quality
Feb 2014
41
ISQC 160101 : 1988
/ IECQC 160101:1993
Electrical relays, blank detail specification:
electromechanical all-or-nothing relays of assessed
quality, test schedules 1, 2 and 3
Feb 2009
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 35(6529)
Measuring relays and protection equipment – Part 1:
Common requirements
2
DOC.ETD 35(6530)
Electrical relays – Part 5: Insulation coordination for
measuring relays and protection equipment –
requirements and tests
3
DOC.ETD 35(6531)
Electrical relays Part 8: Thermal electrical relays
4
DOC.ETD 35(6532)
Measuring relays and protection equipment – Part 11:
Voltage dips, short interruptions, variations and ripple
on auxiliary power supply port
5
DOC.ETD 35(6533)
Electrical relays Part 12: Directional relays and power
relays with two input energizing quantities
6
DOC.ETD 35(6534)
Electrical relays Part 13: Biased (percentage)
differential relays
7
DOC.ETD 35(6535)
Electrical relays Part 16: Impedance measuring relays
8
DOC.ETD 35(6536)
Electrical relays Part 21: Vibration, shock, bump and
seismic test on measuring relays and protection
equipment section one — vibration tests (sinusoidal)
9
DOC.ETD 35(6537)
Electrical relays Part 21: Vibration, shock, bump and
seismic tests on measuring relays and protection
equipment section two — shock and bump tests
10
DOC.ETD 35(6538)
Electrical relays — Part 21: Vibration, shock, bump
and seismic tests on measuring relays and protection
equipment — section 3: seismic tests
11
DOC.ETD 35(6539)
Measuring relays and protection equipment – Part 221: Electrical disturbance tests – 1 mhz burst immunity
tests
12
DOC.ETD 35(6540)
Measuring relays and protection equipment – Part 222: Electrical disturbance tests – electrostatic discharge
tests
13
DOC.ETD 35(6541)
Measuring relays and protection equipment – Part 223: Electrical disturbance tests – radiated
electromagnetic field immunity
14
DOC.ETD 35(6542)
Measuring relays and protection equipment – Part 224: Electrical disturbance tests – electrical fast
transient/burst immunity test
15
DOC.ETD 35(6543)
Measuring relays and protection equipment – Part 225: Electrical disturbance tests – surge immunity test
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
102
16
DOC.ETD 35(6544)
Electrical relays – Part 22-6: Electrical disturbance
tests for measuring relays and protection equipment –
Immunity to conducted disturbances induced by radio
frequency fields
17
DOC.ETD 35(6545)
Electrical relays – Part 22-7: Electrical disturbance
tests for measuring relays and protection equipment –
Power frequency immunity tests
18
DOC.ETD 35(6546)
Electrical relays – Part 24: Common format for
transient data exchange (COMTRADE) for power
systems
19
DOC.ETD 35(6547)
Electrical relays Part 25: Electromagnetic emission
tests for measuring relays and protection equipment
20
DOC.ETD 35(6548)
Measuring relays and protection equipment – Part 26:
Electromagnetic compatibility requirements
21
DOC.ETD 35(6549)
Measuring relays and protection equipment – Part 27:
Product safety requirements
22
DOC.ETD 35(6550)
Measuring relays and protection equipment – Part 127:
Functional requirements for over/under voltage
protection
23
DOC.ETD 35(6551)
Measuring relays and protection equipment –Part 151:
Functional requirements for over/under current
protection
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
103
ETD 36 TOOLS AND EQUIPMENTS FOR LIVE WORKING
SCOPE - To prepare standard on electrical and mechanical characteriistics as well as
reliability requirements for tools and eqipment used in connections with work
on energized electrical systems
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 13771:2013
Live Working - Conductive Clothing for use at Nominal
Voltage Up to 800 Kv A.C. and +/- 600 Kv D.C. (first
revision)
2
* IS 13772:1993
/ IEC 60900:1989
Hand tools for live working up to 1000 V ac and 1500 V Dec 2009
dc
3
IS 13773:1993
/ IEC 60984:1990
Sleeves of insulating material for live working
Dec 2009
4
IS 13774:2014
Live Working - Gloves of Insulating Material (first
revision )
Feb 2014
5
IS 13961:1994
/ IEC 60832:1988
Insulating poles (insulating sticks) and universal tool
attachments (fittings) for live working
Dec 2009
6
IS 14956:2014
Live Working - Minimum Approach Distances for a.c.
Systems in the Voltage Range 72,5 Kv To 800 Kv - A
Method of Calculation (first revision)
Jan 2014
7
IS 14957:2001
/ IEC 61057:1991
Aerial devices with insulating boom used for live
working
Jun 2011
8
IS 14981:2001
/ IEC 61219:1993
Live working - Earthing or earthing and short-circuiting
equipment using lances as a short-circuiting device lance earthing
Jun 2011
9
IS 14993:2001
/ IEC 61236:1993
Saddles, pole clamps (stick clamps) and accessories
for live working
Jun 2011
10
* IS 15405(Part 1):2003
/ IEC 61482-1:2002
Live Working - flame resistance materials for clothing
for thermal protection of working thermal hazards of an
electric arc Part 1 Test Methods
Nov 2013
11
IS 15407:2003
/ IEC 61278:1997
Live working - Guidelines for dielectric testing of tools
and equipment
Nov 2013
12
IS 15416:2003
/ IEC 60743:2001
Live working - Terminology for tools equipments and
devices (Superceding IS 13985)
Dec 2013
13
IS 16155:2014
Live Working - Conformity Assessment Applicable to
Tools, Devices and Equipment
Feb 2014
14
IS 16167(Part 1):2014
Live Working - Insulating Foam-Filled Tubes and Solid
Rods Part 1: Tubes and Rods of a Circular CrossSection
Feb 2014
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 36(6627)
/ IEC 60900 (2012)
Live Working - Hand Tools for use up to 1000 V A.C.
and 1500 V D.C. (first revision of IS 13772)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
104
Dec 2013
1
ETD 37 CONDUCTORS AND ACCESSORIES FOR OVERHEAD LINES
SCOPE - To prepare standards for conductors and accessories for overhead power
lines and codes of practice for the design, installation and maintainance or
overhead power lines
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 398(Part 1):1996
| IEC 60889:1987
Aluminium conductors for overhead transmission
purposes: Part 1 Aluminium stranded conductors (third
revision)
Sep 2012
1
2
IS 398(Part 2):1996
| IEC 889 :1987
Aluminium conductors for overhead transmission
purposes: Part 2 Aluminium conductors, galvanized
steel reinforced (third revision)
Sep 2012
3
3
IS 398(Part 3):1976
Aluminium conductors for overhead transmission
purposes: Part 3 Aluminium conductors, aluminized
steel reinforced (second revision)
Jul 2009
3
4
IS 398(Part 4):1994
| IEC 60208:1966
Aluminium conductors for overhead transmission
purposes: Part 4 Aluminium alloy stranded conductors
(aluminium magnesium silicon type) (third revision)
Jul 2009
1
5
IS 398(Part 5):1992
Aluminium conductors for overhead transmission
purposes: Part 5 Aluminium conductors, galvanized
steel reinforced for extra high voltage (400 kV and
above) (first revision)
Sep 2012
2
6
IS 1778:1980
Reels and drums for bare conductors (first revision)
(superseding IS:2889)
Jul 2009
1
7
IS 2121(Part 1):1981
Conductors and earth wire accessories for overhead
power lines: Part 1 Armour rods, binding wires and
tapes for conductors (first revision)
Sep 2012
8
IS 2121(Part 2):1981
Conductors and earth wire accessories for overhead
power lines: Part 2 Mid span joints and repair sleeves
for conductors (first revision)
Sep 2012
9
IS 2121(Part 3):1992
Conductors and earthwire accessories for overhead
power lines: Part 3 Accessories for earthwire (first
revision)
Sep 2012
10
IS 2121(Part 4):1991
Conductors and earth wire accessories for overhead
power lines : Part 4 Non-tension joints (first revision)
Sep 2012
11
IS 2532:1965
Hard-drawn copper wire for telegraph and telephone
purposes
Sep 2012
12
IS 2665:1964
Cadmium-copper wire for telegraph and telephone
purposes
Sep 2012
4
13
IS 3402:1965
Cadmium-copper conductors for overhead railway
traction
Sep 2012
1
14
IS 3476:1986
Trolley and contact wire for electric traction (first
revision)
15
IS 5613(Part 1/Sec 1):1985
Code of practice for design, installation and
maintenance of overhead power lines: Part 1 Lines
upto and including 11 kV, Section 1 Design (first
revision)
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
105
Jul 2009
Sep 2012
16
IS 5613(Part 1/Sec 2):1989
Code of practice for design, installation and
maintenance of overhead power lines: Part 1 Lines
upto and including 11 kV, Section 2 Installation and
maintenance (first revision)
Sep 2012
17
IS 5613(Part 2/Sec 1):1985
Code of practice for design, installation and
maintenance of overhead power lines: Part 2 Lines
above 11 kV and upto and including 220 kV, Section 1
Design (first revision)
Sep 2012
1
18
IS 5613(Part 2/Sec 2):1985
Code of practice for design, installation and
maintenance of overhead power lines: Part 2 Lines
above 11 kV and upto and including 220 kV, Section 2
Installation and maintenance (first revision)
Sep 2012
3
19
IS 5613(Part 3/Sec 1):1989
Code of practice for design, installation and
maintenance of overhead power lines: Part 3 400 kV
lines, Section 1 Design
Jul 2009
1
20
IS 5613(Part 3/Sec 2):1989
Code of practice for design, installation and
maintenance of overhead power lines: Part 3 400 kV
lines, Section 2 Installation and maintenance
Jul 2009
21
IS 9511:1980
Earth knobs for neutral conductors
Jul 2009
22
IS 9708:1993
Stockbridge vibration dampers for overhead power
lines (first revision)
Mar 2014
23
IS 10162:1982
Spacers and spacer dampers for twin horizontal
bundle conductors
Sep 2012
24
IS 12048:1987
Helically formed fittings for overhead lines upto 33 kV
Sep 2012
25
IS 14214:1994
Annealed stranded copper conductors for electric
traction
Jul 2009
26
IS 15976:2013
Specification for Steel Reels and Drums for Bare
Conductor
Sep 2013
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
106
1
ETD 39 FUSES
SCOPE - To prepare standards regarding specification for all types of fuses, with the
object of determining :
a) The characteristics which are essential in specifying the conditions for
installation and operation of the fuses
b) The requirements to be met by the fuses and the tests designed to
ascertain their compliance with such requirements as well as the procedures
to be followed for these tests
c) Markings
To prepare for these fuses standards, standard values of:
1) Characteristics, rated voltages, currents and breaking capacities:
2) Dimensions in connections with the fixing and interchangeability of high
voltage and low voltage fuses
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 2086:1993
Carriers and bases used in rewirable type electric
fuses for voltages upto 650 V(third revision)
(Superseding IS 8724)
Mar 2014
1
1
2
IS 8187:1976
| IEC 269-3(1973)
D-type fuses
Mar 2011
3
IS 9385(Part 1):1979
| IEC 282-1(1979)
High voltage fuses:Part 1 Current limiting fuses
Sep 2012
4
IS 9385(Part 2):1980
| IEC 282-2(1970)
High voltage fuses:Part 2 Expulsion and similar fuses
(superseding IS:5792)
Sep 2012
5
IS 9385(Part 3):1980
| IEC 282-2(1970)
High voltage fuses:Part 3 Application guide for high
voltage fuses
Sep 2012
6
IS 9385(Part 4):1983
High voltage fuses:Part 4 Determination of short-circuit
power factor for testing of high voltage fuses
Sep 2012
7
IS 9385(Part 5):1983
| IEC 282-1A(1978)
High voltage fuses:Part 5 Types and dimensions of
fuse-links for current limiting fuses
Mar 2011
8
IS 9402:1980
| IEC 549(1976)
High voltage fuses for the external protection of shunt
power capacitors
Sep 2012
9
IS 9926:1981
Fuse wires used in rewirable type electric fuses upto
650 volts
Mar 2011
10
IS 10624:1983
| IEC 644(1979)
High voltage fuse-links for motor circuit applications
Mar 2011
11
IS 12534:1988
Application guide for the selection of high voltage fuses Sep 2012
for transformer circuit applications
12
IS 13703(Part 1):1993
/ IEC 60269-1(1986)
Low voltage Fuses for voltages not exceeding 1000 V
ac or 1500 V dc: Part 1 General requirements
[superseding IS 9224 (Part 1):1979]
Mar 2014
13
IS 13703(Part 2/Sec 1):1993
/ IEC 60269-2(1986)
Low voltage fuses for voltages not exceeding
1000 V ac or 1500 V dc: Part 2 Fuses for use by
authorized persons, Section 1 Supplementary
requirements [superseding IS 9224 (Part 2):1979]
Mar 2014
14
IS 13703(Part 2/Sec 2):1993
/ IEC 60269-2-1(1987)
Low voltage fuses for voltages not exceeding
1000 V ac or 1500 V dc: Part 2 Fuses for use by
authorized persons, Section 2 Examples of
standardized fuses
Mar 2014
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
107
15
IS 13703(Part 4):1993
/ IEC 60269-4(1986)
Low voltage fuses for voltages not exceeding 1000 V
ac or 1500 V dc: Part 4 Supplementary requirements
for fuse- links for the protectlon of semiconductor
devices
[superceding IS 9224 (Part 4):1980]
Mar 2014
16
IS 60127(Part 1):2006
/ IEC 60127-1(2006)
Miniture fuses: Part 1 Definitions for miniature fuses
and general requirements for miniature fuse links(first
revision)
Mar 2014
17
IS 60127(Part 2):2003
/ IS/IEC 60127-2:2003
Ministure fuses : Part 2 Cartridge fuse links (First
Revision)
Jun 2009
18
IS 60127(Part 4):2005
/ IEC 60127-4(2005)
Miniature fuses: Part 4 Universal modular fuse Link
(UMF)
Mar 2014
19
IS 60127(Part 5):1988
Miniature fuses: Part 5 Guidelines for quality
assessment of miniature fuse-links
Feb 2011
20
IS 60127(Part 6):1994
/ IEC 60127-6:1994
Miniature fuses: Part 6 Fuse holders for miniature
cartridge fuse links
Sep 2012
21
IS 60691:1993
/ IEC 60691:1993
Thermal links - requirements and application guide
Sep 2012
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 39(6159)
Thermal links - Requirements and application guide
IEC 60691:2002 (Superseding IS/IEC 691:1993)
2
DOC.ETD 39(6164)
High - voltage fuses - Part 2: Expulsion fuses
IEC 60282-2 : 2008 (Superseding IS 9385 (Part 2)
;1980
3
DOC.ETD 39(6426)
/ IEC 60269-2 : 2006
Low voltage fuses : Part 2 Supplementary
requirements for fuses for use by authorized (fuses
mainly for industrial application) Examples of
standardized systems of fuses A to J (Superseding IS
13703(Part 2/Sec2)
4
DOC.ETD 39(6427)
/ IEC 60269-3:2006
Low voltage fuses - Part 3: Supplementary
requirements for fuse for use by unskilled persons
(fuses mainly for household and similar applications)
Example of standardized systems of fuses A to F
5
DOC.ETD 39(6428)
/ IEC 60269-4 : 2009
Low-voltage fuses – Part 4: Supplementary
requirements for fuse-links for the protection of
semiconductor devices
6
DOC.ETD 39(6429)
/ IEC 60269-5 : 2010
Low-voltage fuses. Part 5: Guidance for the application
of low-voltage fuses
7
DOC.ETD 39(6430)
/ IEC 60269-6 : 2010
Low-voltage fuses – Part 6: Supplementary
requirements for fuse-links for the protection of solar
photovoltaic energy systems
8
DOC.ETD 39(6431)
/ IEC 60282-1 : 2009
High-voltage fuses. Part 1: Current-limiting fuses
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
108
ETD 40 HVDC POWER SYSTEMS
SCOPE - To prepare standards and guidelines on equipment and performance of
high- voltage d.c(HVDC) Transmission Systems
Sl. No. IS Number/ DOC Number
Title
Reaffirm
No. of
Date
Amd.
STANDARDS PUBLISHED
1
IS 2165(Part 5):2005
/ IEC 60071-5:2002
Insulation coordination:Part 5 Procedures for highvoltage direct current (HVDC) converter stations
Dec 2010
2
IS 14801:2000
/ IEC 60633(1998)
Terminology for high voltage direct
current ( HVDC ) transmission.
Jun 2010
3
IS 14902(Part 1):2013
| IEC/TR 60619-1:2010
Performance of high-voltage direct current (HVDC)
systems with line-commutated converters – Part 1:
Steady-state conditions ([First Revision)
4
IS 14902(Part 2):2013
| IEC/TR 60619-2:2008
Performance of high-voltage direct current (HVDC)
systems with line-commutated converters -- Part 2:
Faults and switching (First Revision)
5
IS 14902(Part 3):2013
| IEC/TR 60619-3:2009
Performance of high-voltage direct current (HVDC)
Systems with line-commutated converters – Part 3:
Dynamic conditions (First Revision)
6
IS 14911(Part 1):2001
/ IE 60700-1(1998)
Thyristor valves for high-voltage direct current (HVDC)
power transmission: Part 1 Electrial Testing
Jan 2011
7
IS 15597:2005
/ IEC 61803:1999
Determination of power losses in high voltage direct
current (HVDC) converter stations
Dec 2010
8
IS 15617:2005
/ IEC 61954:2003
Power electronics for electrical transmission and
distribution systems-Testing of thyristor valves for
static var compensations
Dec 2010
9
IS 16071:2013
| IEC 62001:2003
High-voltage direct current (HVDC) systems –
Guidebook to the specification and design evaluation
of a.c. filters
10
IS 16075:2013
| (IEC 62501:2009
Voltage sourced converter (VSC) Valves for highvoltage direct current (HVDC) Power transmission –
electrical testing
11
IS 16076:2013
| IEC 61975:2010
High-voltage direct current (HVDC) installations –
system tests
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 40(6672)
Static var compensators (SVC) – Testing of thyristor
valves (First Revision) [IEC 61954 (2013)]
2
DOC.ETD 40(6673)
High voltage direct current (HVDC) substation audible
noise [IEC 61973 (2012)]
3
DOC.ETD 40(6674)
High-voltage direct current (HVDC) power
transmission using voltage sourced converters (VSC)
[IEC 62543 (2011)]
4
DOC.ETD 40(6675)
High-voltage direct current (HVDC) systems –
Application of active filters [IEC 62544 (2011)]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
109
ETD 42 WIND TURBINES
SCOPE - To prepare Indian standards for wind turbines that convert wind energy into
electrical energy. These standards address
design requirements, engineering integrity, measurement techniques and
test procedures. Their purpose is to provide a basis for design, quality
assurance and certification. The standards are concerned with all
subsystems of wind turbines, such as mechanical and internal electrical
systems, support structures and control and protection systems. They are
intended to be used together with appropriate Indian Stanfdards.
Sl. No. IS Number/ DOC Number
Title
STANDARDS PUBLISHED
1
IS 61400(Part 13):2001
/ IS/IEC 61400-13:2001
Wind turbines generator systems - Part 13:
Measurement of mechanical loads
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 42(6422)
Wind turbines – Part 21: Measurement and
assessment of power quality characteristics of grid
connected wind turbines [IEC 61400-21:]
2
DOC.ETD 42(6423)
Wind turbines – Part 24: Lightning protection [IEC
61400-24:]
3
DOC.ETD 42(6424)
Electrotechnical Vocabulary – Part 415: Wind Turbine
Generator Systems [IEC 60050-415:1999]
DRAFT STANDARDS ISSUED IN WIDE CIRCULATION
1
DOC.ETD 42(6717)
Wind turbines – Part 4: Design requirements for wind
turbine gearboxes [IEC 61400-4:2012]
2
DOC.ETD 42(6718)
Wind turbines – Part 11: Acoustic noise measurement
techniques [IEC 61400-11:2012]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
110
Reaffirm
No. of
Date
Amd.
ETD 43 Standardization of environmental aspects for electrical and electronic products
SCOPE - To prepare the necessary guidelines, basic standards, in the environmental
area, in close cooperation with product committees, which remain
autonomous in dealing with the environmental aspects relevant to their
products;
To liaise with product committees in the elaboration of environmental
requirements of product standards in order to foster common technical
approaches and solutions for similar problems and thus assure consistency
in standards.
Sl. No. IS Number/ DOC Number
Title
STANDARDS PUBLISHED
1
IS 16197(Part 1):2014
/ IEC 62321-1:2013
Determination of certain substances in electrotechnical
products : Part 1 Introduction and overview
2
IS 16197(Part 2):2014
/ IEC 62321-2:2013
Determination of certain substances in electrotechnical
products – Part 2: Disassembly, disjointment and
mechanical sample preparation
3
IS 16197(Part 3/Sec 1):2014
/ IEC 62321-3-1:2013
Determination of Certain Substances in
Electrotechnical Products Part 3 Screening Section 1
Lead, Mercury, Cadmium, Total Chromium and Total
Bromine Using X-Ray Fluorescence Spectrometry
4
IS 16197(Part 3/Sec 2):2014
/ IEC 62321-3-2:2013
IS 16197 (Part 3/Section 2) : 2014 Determination of
Certain Substances in Electrotechnical Products Part
3 Screening Section 2 Total Bromine in Polymers and
Electronics by Combustion ─ ION Chromatography
5
IS 16197(Part 4):2014
/ IEC 62321-4:2013
IS 16197 (Part 4) : 2014 Determination of Certain
Substances in Electrotechnical Products Part 4
Mercury in Polymers, Metals and Electronics by CVAAS, CV-AFS, ICP-OES and DICP-MS
6
IS 16197(Part 5):2014
/ IEC 62321-5:2013
Determination of Certain Substances in
Electrotechnical Products Part 5 Cadmium, Lead and
Chromium in Polymers and Electronics and Cadmium
and Lead in Metals by AAS, AFS, ICP-OES and ICPMS
FINALISED DRAFTS UNDER PRINT
1
DOC.ETD 43(6327)
Environmentally conscious design for electrical and
electronic products [IEC 62430(2009)]
2
DOC.ETD 43(6328)
Guidance for evaluation of products with respect to
substance-use restrictions in electrical and electronic
products’ [IEC 62476(2010)]
3
DOC.ETD 43(6329)
Environmental Information on Electrical and Electronic
Equipment (EIEEE) [IEC/PAS 62545:2008]
4
DOC.ETD 43(6330)
Electrotechnical Products – Determination of
Restricted Substances – Sampling Procedure –
Guidelines [IEC/PAS 62596:2009]
* INDICATES STANDARDS UNDER REVISION
** INDICATES STANDARDS TO BE REVISED
/ INDICATES DUAL NUMBER STANDARDS
| INDICATES EQUIVALENT STANDARDS
111
Reaffirm
No. of
Date
Amd.
ANNEX 1
STANDARDS WITHDRAWN / SUPERSEDED
Sl. No. IS Number/ DOC Number
Title
1
DOC.ETD 29(6201)
A,C motor capacitors - Part 1 : General - performance, testing and rating Motor start capacitors safety requirements - Guide for installation and
operation (third revision of IS 2993) (IEC 60252-1-2001)
2
SP 39 : 1987
Special publication-Guide for insulation
coordination within low voltage systems
3
SP 48 : 1991
Guide for requirements and testing of electric irons
4
SP 49 : 1991
Guide for requirements and testing of
electric immersion water heaters
5
SP 50 : 1991
Guide for requirements and testing of electric radiators
6
SP 51 : 1991
Guide for requirements and testing of electric stoves
7
DOC.ETD 29(6197)
A,C motor capacitors - Part 2: Motor start capacitors (third revision of IS
2993) (IEC 60252-2-2003)
8
IS 13:1949
Methods for grading processed mica (tentative) (withdrawn)
9
IS 14:1949
Classification of processed muscovite mica (tentative) (withdrawn)
10
IS 203:1984
Dry batteries for flashlights (fourth revision)
11
IS 267:1976
Inert cells (third revision)
12
IS 268:1976
Leclanche type sack cells (second revision)
13
IS 282:1982
Hard-drawn copper conductors for overhead power transmission (second
revision)
14
IS 302(Part 2/Sec
205):1994
Safety of household and similar electrical appliances: Part 2 Particular
requirements,
Sec 205 Steam irons
15
IS 350:1968
Organic, baking, impregnating, insulating varnishes for electrical purposes
(first revision) (with Amendments No. 1 to 3)
16
IS 351:1952
Insulated varnish, baking, bitumen type (with Amendments No. 1 and 2)(withdrawn)
17
IS 352:1973
Air-drying insulating varnishes for electrical purposes (first revision )(withdrawn)
18
IS 353:1952
Insulating varnish, non-alcoholic, clear, air-drying (withdrawn)
19
IS 370:1954
Reversible type two-pin plugs and socket-outlets without earthing
connections (tentative) (withdrawn)
20
IS 375:1963
Marking and arrangement for switchgeasr bus-bars, main connections and
auxiliary wiring (revised)
(superseded by IS: 5578 and IS:11353)
21
IS 395:1962
Lead-acid storage battery for motor vehicles (superseded by IS: 7372)
22
IS 396:1953
Bare annealed high-conductivity copper wire for electrical machinery and
apparatus (tentative) (withdrawn)
23
IS 434(Part 1):1964
Rubber-insulated cables: Part 1 With copper conductor (revised)
(superseded by IS: 9968)
24
IS 434(Part 2):1964
Rubber-insulated cables: Part 2 With aluminium conductors (revised)
(supersededby IS: 9968)
25
IS 449:1962
Enamelled high-conductivity annealed round copper wire (oleoresinous
enamel) (revised) (withdrawn)
Sl. No. IS Number/ DOC Number
Title
26
IS 450:1964
Cotton covered round copper conductors (revised) [superseded by IS
7391(Part 1)]
27
IS 541:1954
Stationary, accumulators, lead-acid type (superseded by IS: 1651 and IS:
1652)
28
IS 556:1960
Leclanche type radio batteries (withdrawn)
29
IS 585:1962
Voltages and frequency for transmission and distribution systems (revised)
(Amendments No. 1 to 5) (superseded by IS:12360-1988)
30
IS 691:1984
Flexible trailing cables for use in coal mines (first revision)
31
IS 693:1965
Varnished cambric insulated cables (revised) (with Amendments No. 1 to
5) (withdrawn)
32
IS 722(Part 2):1977
AC electricity meters:Part 2 Single-phase whole-current watt hour meters,
Class2 (first revision)
33
IS 722(Part 3):1988
AC electricity meters: Part 3 Three-phase whole current and transformer
operated and single-phase transformer operated watt-hour meters, class
2(second revision)
34
IS 722(Part 5):1980
AC electricity meters: Part 5 Volt-ampere hour meters for restricted power
factor range, class 3.5 (first revision)
35
IS 722(Part 6):1980
AC electricity meters: Part 6 Var-hour meters, class 2.5 (first revision)
36
IS 722(Part 7/Sec
1):1987
AC electricity meters: Part 7 Volt-ampere hour meters for full power factor
range, Section 1 General requirements (first revision)
37
IS 722(Part 7/Sec
2):1987
AC electricity meters: Part 7 Volt-ampere hour meters for full power factor
range, Section 2 Vector sum VAh meters (first revision)
38
IS 722(Part 7/Sec
3):1987
AC electricity meters: Part 7 Volt-ampere hour meters for full power factor
range, Section 3 Arithmatic sum VAh meters (first revision)
39
IS 722(Part 8):1972
AC electricity meters: Part 8 Single-phase 2-wire whole current watthour
meter (class 1.0)
40
IS 722(Part 9):1972
AC electricity meters: Part 9 Three-phase whole current and transformer
operated watthour meters and single-phase two-wire transformer
operated watthour meters (class 1.0)
41
IS 985:1962
Lead-acid storage batteries for motor vehicles (special) (revised)
(supersded by IS:7372)
42
IS 1025:1957
Glossary of terms for primary cells and batteries [superseded by IS: 1885
(Part15)
43
IS 1026:1984
Flexible trailing cables for use in quarries and metalliferous mines (first
revision)
44
IS 1027:1968
Paper insulated cables for use in mines (superseded by IS: 692)
45
IS 1087:1957
Single pole 5-ampere tumbler switches for AC/DC (withdrawn)
46
IS 1119:1957
Reversible protected type two-pin plugs and sockets with earthing
connections (withdrawn)
47
IS 1147:1957
Glossary of terms for secondary cells and batteries [superseded by IS:
1885 (Part 8)]
48
IS 1174:1957
Definitions for mica terms
[superseded by IS:1885(Part 53)]
49
IS 1336:1959
Recommendations for the colour of push-buttons [superseded by IS: 6875
(Part 2)]
50
IS 1416:1972
Safety transformers (first revision)
51
IS 1496:1959
Transformers used in vibrator power supplies (withdrawn)
Sl. No. IS Number/ DOC Number
Title
52
IS 1534(Part 1):1977
Ballasts for fluorescent lamps. Part 1: For switch start circuits (second
revision)
53
IS 1565:1966
Electrical apparatus comprising resistors (revised) (superseded by
IS:10659 andIS:11067)
54
IS 1567:1960
Metal-clad switches(current rating not exceeding 100 amperes);
(superseded by IS:2607 and IS:4064)
55
IS 1591:1960
Glossary of terms for cables, conductors and accessories [superseded by
IS:1885(Part 32)]
56
IS 1594:1960
Metric sizes of copper wires and conductors for electrical purposes
(withdrawn)
57
IS 1595:1967
Enamelled round copper wire with high mechanical properties (withdrawn)
58
IS 1596:1977
Polyethylene insulated cables for working voltages upto and including
1100 V (second revision) (withdrawn)
59
IS 1653:1972
Rigid steel conduits for electrical wiring (second revision)
(withdrawn){Superseded by IS 9537(Part 2)}
60
IS 1666:1961
Paper-covered rectangular copper conductors for transformer windings
[superseded by IS:7404(Part 2)]
61
IS 1753:1967
Aluminium conductors for insulated cables (first revision) (withdrawn) (see
IS:8130)
62
IS 1777:1978
Industrial luminaires with metal reflectors (first revision)
63
IS 1818:1972
Alternating current isolators (disconnectors) and earthing swithces (first
revision) (Amendments No. 1 and 2) (withdrawn)
64
IS 1822:1967
AC motor starters of voltage not
exceeding 1000 volts [(first revision)- (withdrawn)]
65
IS 1846:1992
Lead-acid aircraft batteries (aerobatic and non-aerobatic) (first revision)
66
IS 1860:1980
Code of Practice for installation, operation and maintennannce of electric
passenger and goods lifts (first revision)
67
IS 1885(Part 8):1986
Electrotechnical vocabulary:
Part 8 Secondary cells and batteries (first revision) (superseding IS:1174)
68
IS 1885(Part 73/Sec
1):1993
Electrotechnical vocabulary: Part 73 Physics and Chemistry, Section 1
Physical concepts
69
IS 1885(Part 73/Sec
2):1993
Electrotechnical Vocabulary: Part 73 Physics and chemistry, Section 2
Electrotechnical concepts
70
IS 1885(Part 73/Sec
3):1993
Electrotechnical Vocabulary: Part 73 Physics and chemistry, Section 03
Concepts related to quantities and units
71
IS 1886:1961
Code of practice for installation and maintenance of transformers (first
revision) [superseded by IS:10028(Part 2 and 3)
72
IS 1913(Part 1):1978
General and safety requirements for luminaires:
Part 1 Tubular fluorescent lamps (second revision)
73
IS 1947:1980
Flood lights (first revision) (withdrawn)
74
IS 1951:1961
Polyvinylchloride sleeving for electrical purpose
75
IS 2032(Part 1):1962
Graphical symbols used in electrotechnology: Part 1 Classification and
definitions of diagrams and charts [superseded by IS:8270(Part 1)]
76
IS 2032(Part 2):1962
Graphical symbols used in electrotechnology: Part 2 Kind of current
distribution systems and methods of connection (withdrawn)
77
IS 2032(Part 3):1962
Graphical symbols used in electrotechnology: Part 3 Circuit elements and
variability (withdrawn)
Sl. No. IS Number/ DOC Number
Title
78
IS 2032(Part 4):1964
Graphical Symbols used in electrotechnolgy:
Part 4 Rotating machines and transformers
[superseded by IS 2032(Part 26) and IS 2032 (Part 28)]
79
IS 2032(Part 5):1965
Graphical symbols used in electrotechnology: Part 5 Generating stations
and substations (withdrawn)
80
IS 2032(Part 6):1965
Graphical symbols used in electrotechnology: Part 6 Motor starters
(withdrawn)
81
IS 2032(Part 7):1974
Graphical symbols used in electrotechnology: Part 7 Switchgear and
auxiliaries(first revision) (withdrawn)
82
IS 2032(Part 10):1969
Graphical symbols used in electrotechnology: Part 10 Measuring
instruments (withdrawn)
83
IS 2032(Part 11):1969
Graphical symbols used in electrotechnology: Part 11 Electrical
installations in buildings (withdrawn)
84
IS 2032(Part 18):1976
Graphical symbols used in electrotechnology: Part 18 Symbols and
connection diagrams for integrating meters (withdrawn)
85
IS 2032(Part 21):1977
Graphical symbols used in electrotechnology: Part 21 Electrical welding
equipment (withdrawn)
86
IS 2032(Part 22):1978
Graphical symbols used in electrotechnology: Part 22 Instrument
transformers (withdrawn)
87
IS 2032(Part 23):1978
Graphical symbols used in electrotechnology: Part 23 Instruments for
process measurement and control (withdrawn)
88
IS 2032(Part 26):1982
Graphical symbols used in electrotechnology: Part 26 Rotating machines
(withdrawn)
89
IS 2032(Part 27):1982
Graphical symbols used in electrotechnology: Part 27 Relays (withdrawn)
90
IS 2032(Part 28):1983
Graphical symbols used in electrotechnology: Part 28 Transformers
(withdrawn)
91
IS 2068:1962
Cotton covered rectangular copper conductors [superseded by IS: 7391
(Part 2)]
92
IS 2070:1962
Methods of impulse voltage testing
(superseded by IS:2071)
93
IS 2071(Part 2):1974
Methods of high voltage testing: Part 2 Test procedures (first revision)
94
IS 2120:1963
15-ampere tumbler switches (revised) (with amendments No. 1 and 2)
(superseded by IS: 3854)
95
IS 2147:1962
Degrees of protection provided by enclosures
for low voltage switchgear and controlgear
[(superseded by IS 13947: (Part 1):1993]
96
IS 2148:2004
Electrical apparatus for explosive gas atmospheres - Flameproof
enclosures "d" (third revision)
97
IS 2149:1970
Luminaires for street lighting (first revision) (withdrawn)[Superseded by IS
10322 (Part 5/Section 3)]
98
IS 2183:1973
Schedule for high pressure mercury vapour lamps (first revision) with
Amendment No. 1) [superseded by IS:9900(Part 1) to (Part 4)
99
IS 2188:1962
Methods of test for paper for electrical purposes (withdrawn)
100
IS 2206(Part 1):1984
Flameproof electric lighting fittings:
Part 1 Well-glass and bulkhead types (first revision)
101
IS 2206(Part 2):1976
Flameproof electric lighting fittings:
Part 2 Fittings using glass tubes
Sl. No. IS Number/ DOC Number
Title
102
IS 2206(Part 3):1989
Flameproof electric lighting fittings:
Part 3 Fittings using plastic tubes (Group I only)
103
IS 2206(Part 4):1987
Flameproof electric lighting fittings:
Part 4 Portable flameproof hand lamps
104
IS 2208:1962
HRC cartridge fuse links for voltage above 650 volts [(superseded by
IS:9224(Part 2)]
105
IS 2274:1963
Code of practice for electrical wiring installations (system voltage
exceeding 650 volts) (superseded by IS:732)
106
IS 2448(Part 2):1968
Adhesive insulating tapes for electrical purposes:
Part 2 Tapes with PVC substrates (Amendment No.1 to 3)- (withdrawn)
107
IS 2493:1963
Well glass lighting fittings for use underground in mines (non-flameproof
types)(withdrawn)
108
IS 2509:1973
Rigid non-metallic conduits for electrical installations (first revision)
(withdrawn) (superseded by IS 9537(Part 3)
109
IS 2516(Part 1/Sec
2):1980
Circuit-breakers: Part 1 General and definitions, Section 2 For voltages
above 1000V ac (first revision) (Superseded by IS 13118:1991)
110
IS 2516(Part 1/Sec
3):1972
Circuit breakers: Part 1 General and definitions, Section 3 Voltages above
11 kV
111
IS 2516(Part 2/Sec
2):1980
Circuit breakers: Part 2 Rating, Section 2 For voltages above 1 000 V ac
(first revision) (Superseded by IS 13118:1991)
112
IS 2516(Part 3/Sec
2):1980
Circuit breakers : Part 3 Design and construction, Section 2 for Voltages
above1 000 V ac (first revision) (Superseded by IS 13118:1991)
113
IS 2516(Part 4/Sec
2):1980
Circuit breakers: Part 4 Type tests and routine tests, Section 2 For
voltages above 1 000 V ac (first revision) (superseded by IS 13118:1991)
114
IS 2516(Part 5/Sec
2):1980
Circuit breakers: Part 5 Information to be given with enquiries tenders and
orders and rules for transport erection and maintenance, Section 2 For
volages above 1 000 V ac (first revision) (superseded by IS 13118:1991)
115
IS 2516(Part 1&2/Sec
1):1985
Circuit breakers: Part 1 & 2 Requirements and tests:
Section 1 Voltages not exceedding 1 000 V ac or 1 200 V dc (second
revision) [superseded by IS 13947(Part 2):1993]
116
IS 2576:1975
Dry batteries for transistor radio receivers (first revision)
117
IS 2607:1967
Air-break isolators for voltages not
exceeding 1 000 volts (first revision)
(superseded by IS:4064)
118
IS 2659:1964
Enamelled round copper wire for elevated temperatures (withdrawn)
119
IS 2667:1988
Fittings for rigid steel conduits for electrical wiring (first revision)
[Superseded by IS 14768(Part 2):2003]
120
IS 2834:1998
Shunt capacitors for power systems (second revision){uperseded by IS
13925(Part 1)}
121
IS 2889:1964
Drums for trolley and contact wire (withdrawn)
122
IS 2959:1985
Contactors for voltages not exceeding
1 000 V ac or 1 200 V dc (first revision)
[superseded by IS 13947 (Part 4/Section 1)]
123
IS 2982:1965
Copper conductors in insulated cables and cords (withdrawn) (see IS:8130)
124
IS 3003(Part 1):1977
Carbon brushes for electrical machines: Part 1 Definitions and
nomenclature (first revision)
125
IS 3003(Part 2):1977
Carbon brushes for electrical machines: Part 2 Test methods for brush
materials(first revision) (superseded by IS 13584:1992)
Sl. No. IS Number/ DOC Number
Title
126
IS 3003(Part 3):1978
Carbon brushes for electrical machines: Part 3 Dimensions and
requirements (first revision) (Superseded by IS 13466:1992)
127
IS 3003(Part 4):1978
Carbon brushes for electrical machines: Part 4 Dimensions of chamfers,
bevels and terminations (first revision) (Superseded by IS 13466:1992)
128
IS 3035(Part 1):1965
Thermoplastic insulated weatherproof cables: Part 1 PVC insulated and
PVC sheathed (amalgamated with IS:694) (withdrawn)
129
IS 3035(Part 2):1965
Thermoplastic insulated weatherproof cables: Part 2 Polyethylene
insulated, taped or untaped, braided and compounded (withdrawn)
130
IS 3035(Part 3):1967
Thermoplastic insulated weatherproof cables: Part 3 Polyethlene sheathed
(amalgamated with IS:1596) (withdrawn)
131
IS 3070(Part 1):1985
Lightning arresters for alternating current systems:
Part 1 Non-linear resistor type lightning arresters
(second revision){Superseded by IS 15086(Part 1)}
132
IS 3070(Part 2):1966
Expulsion type lightning arresters (Amendment No. 1) (withdrawn)
133
IS 3072:1975
Code of practice for installation and
maintenance of switchgear[(first revision)-(withdrawn)]
134
IS 3106:1966
Code of practice for selection, installation maintenance
of fuses [(voltage not exceeding 650 volts)- (withdrawn)]
135
IS 3107:1974
Portable multi purpose direct acting electrical indicating instruments (first
revision)
136
IS 3202:1965
Code of practice for climate proofing
of electrical equipment (withdrawn)
137
IS 3287:1965
Industrial lighting fittings with plastic reflectors
138
IS 3347(Part 6/Sec
1):1977
Dimensions for porcelain transformer bushings for use in lightly polluted
atmospheres: Part 6 72.5 kV bushings, Section 1 Porcelain parts
139
IS 3347(Part 6/Sec
2):1982
Dimensions for porcelain transformer bushings for use in lightly polluted
atmospheres: Part 6 72.5 kV bushings, Section 2 Metal parts
140
IS 3347(Part 7/Sec
1):1977
Dimensions for porcelain transformer bushings for use in lightly polluted
atmospheres: Part 7 123 kV bushings, Section 1 Porcelain parts
141
IS 3347(Part 7/Sec
2):1982
Dimensions for porcelain transformer bushings for use in lightly polluted
atmospheres: Part 7 123 kV bushings, Section 2 Metal parts
142
IS 3454:1966
Paper-covered round copper conductors [superseded by IS:7404 (Part 1)]
143
IS 3482:1966
Electric saucepans (withdrawn)
144
IS 3514:1966
Electric coffee percolators (non-regulator t ype) (Superseded by IS
14144:1994)
145
IS 3534:1976
Outline dimensions of electric lifts (first revision)
146
IS 3765:1966
Varnish impregnated cotton sleevings for electrical purposes
147
IS 3855(Part 1):1978
Rectangular and square enamelled copper conductors: Part 1 Thickness
of enamel coating (first revision)
148
IS 3855(Part 2):1979
Rectngular and square enamelled copper condutors: Part 2 Methods of
tests (first revision)
149
IS 3855(Part 3):1978
Rectangular and square enamelled copper conductors: Part 3 Wires with
high mechanical properties (first revision)
150
IS 3855(Part 4):1981
Rectangular and square enamelled copper conductors: Part 4 Wires with
temperature index 155 (first revision)
151
IS 3855(Part 5):1984
Rectangular and square enamelled copper conductors: Part 5 Wires with
temperature index 180 (first revision)
Sl. No. IS Number/ DOC Number
Title
152
IS 3914:1967
Code of practice for selection of ac induction motor starters [(voltage not
exceding 1 000 volts- (withdrawn)]
153
IS 3961(Part 4):1968
Recommended current ratings for cables: Part 4 Polyethylene insulated
cables
154
IS 4004:1985
Application guide for non-linear resistor type surge arresters for alternating
current system (first revision)
{ Superseded by IS 15086(Part 5)}
155
IS 4012:1967
Dust-proof electric lighting fittings
156
IS 4013:1967
Dust-tight electric lighting fittings
157
IS 4047:1967
Heavy duty air-break switches and
composite units of air-break switches and
fuses for voltages not exceeding 1000 volts
(superseded by IS:4064)
158
IS 4064(Part 1):1978
Air-break switches, air break disconnectors, air-break switch
disconnectors andfuse-combination units for voltages not exceeding
1000V ac or 1200V dc:
Part 1 General requirements (revised)
[superseded by IS 13947 (Part 3):1993]
159
IS 4064(Part 2):1978
Air-break switches,air-break disconnectors,air-break switch disconnectors
and fuse-combination units for voltages not exceeding 1000 V ac or 1200V
dc:
Part 2 Specific requirements for the direct switching
of individual motors(withdrawn)
160
IS 4237:1982
General requirements for switchgear and controlgear for voltages not
exceeding1 000 volts ac or 1 200 volts dc (first revision) [superseded by IS
13947(Part 1):1993]
161
IS 4268:1992
Air depolarized primary wet cells (second revision)
162
IS 4288:1988
PVC insulated (heavy duty) electric cables with solid aluminium conductors
for voltages upto and including 1100 V (second revision) (withdrawn)
163
IS 4615:1968
Switch- socket outlets (non-interlocking type)( Withdrawn)
164
IS 4666:1980
Electric passenger and goods lifts (first revision)
165
IS 4685(Part 2):1984
Varnish bonded glass-fibre covered copper conductors: Part 2
Rectangular conductors (first revision)
166
IS 4691:1985
Degrees of protection provided by enclosure for rotating electrical
machines (first revision) (withdrawn)
167
IS 4710:1968
Switches and switch-isolators above 1000 V but not exceeding 11000 V
(Amendment No. 1) (withdrawn)
168
IS 4718:1968
Multiple paper-covered round copper conductors [superseeds IS:7404
(Part 1)]
169
IS 4722:2001
Rotating electrical machines (second revision) (withdrawn)
170
IS 4728:1975
Terminal marking and direction of rotation for rotating electrical machinery
(first revision) (withdrawn)
171
IS 4729:1975
Measurement and evaluation of vibration of rotating electrical machines
(Superseded by IS 12075:1987))
172
IS 4800(Part 1):1968
Enamelled round winding wires: Part 1 Conductors data
173
IS 4800(Part 2):1968
Enamelled round winding wires: Part 2 Maximum overall diameters
174
IS 4800(Part 3):1968
Enamelled round winding wires: Part 3 Methods of tests
Sl. No. IS Number/ DOC Number
Title
175
IS 4800(Part 4):1968
Enamelled round winding wires: Part 4 Wires with high mechanical
properties [superseeds IS 13730(Part 1):1993/IEC 317-1(1880)]
176
IS 4800(Part 5):1968
Enamelled round winding wires: Part 5 Wires for elevated temperatures
(superseeding IS:2659)
177
IS 4800(Part 6):1968
Enamelled round winding wires: Part 6 Wires with self-fluxing properties
[uperseeds IS 13730(Part 4):1993/IEC 317-4(1990)]
178
IS 4800(Part 7):1970
Enamelled round winding wires: Part 7 Wires with good dielectric
properties under humid conditions [superseeds IS 13730(Part 6):1994]
179
IS 4800(Part 8):1970
Enamelled round winding wires: Part 8 Wires for use in refrigeration
systems
180
IS 4800(Part 9):1971
Enamelled round winding wires: Part 9 Wires with temperature index 180
181
IS 4800(Part 10):1977
Enamelled round winding wires: Part 10 Self bonding wires
182
IS 4800(Part 11):1981
Enamelled round winding wires: Part 11 Wires with temperature index 220
[superseeds IS 13730(Part 7):1993/IEC 317-7(1990)]
183
IS 4800(Part 12):1986
Enamelled round winding wires; Part 12 Self bonding wires heat or solvent
bonding enamelled round copper wires with temperature index 155
184
IS 4800(Part 13):1989
Enamelled round winding wires: Part 13 Dual coated wires with
temperature index200
185
IS 4800(Part 14):1991
Enamelled round winding wires: Part 14 Wires with temperature index
155 [superseeded by IS 13730(Part 20):1993/IEC 317-20(1990)]
186
IS 4817:1968
Rubber-insulated cables for mines (with amendments No. 1 and 2)
(withdrawn)
187
IS 4821:1968
Cable glands and cable sealing boxes for use in mines
188
IS 4850:1968
Application guide for expulsion-type lightning arresters (withdrawn)
189
IS 4949:1968
2 Amp switches for domestic and similar purposes(Superseded by IS
3854)
190
IS 5124:1969
Code of practice for installation and
maintenance of ac induction motor starters
[(voltage not exceeding 1 000 V)-(withdrawn)]
191
IS 5133(Part 1):1969
Boxes for enclosure of the electrical accessories:Part 1 Steel and cast iron
boxes(Superseded by IS 14772)
192
IS 5133(Part 2):1969
Boxes for the enclosure of electrical accessories:Part 2 Boxes made of
insulating material (Superseded by IS 14772)
193
IS 5160:1969
Mains-operated synchronous clocks
(Superseded by IS 14145:1994)
194
IS 5424:1969
Rubber mats for electrical purpose (Superseded by
195
IS 5728:1970
Guide for short-circuit calculations (Superseded by IS 13234:1991)
196
IS 5755:1970
Mineral insulated aluminium sheathed cables with aluminium conductors
(withdrawn)
197
IS 5780:2002
Electrical apparatus for explosive gas atmospheres - Intrinsic safety 'l'
(second revision)
198
IS 5792:1970
High voltage expulsion and similar fuses (superseded by IS:9385(Part 3)
199
IS 5833:1970
Flameproof air-break electrically operated gate-end boxes
200
IS 5868:2000
Polyvinyl chloride insulated cables for rated voltages upto and including
450/750 V : Part 3 Sheathed single and multiore for fixed and flexible
wiring (fourth revision of IS 694)
201
IS 5908:1970
Method of measurement of electrical installations in buildings (withdrawn)
IS 15652:2006)
Sl. No. IS Number/ DOC Number
Title
202
IS 5959(Part 1):1970
Polyethylene insulated and PVC sheathed (heavy duty) electric cables
(Part 1) For working voltages up to and including 1100 volts (withdrawn)
203
IS 5959(Part 2):1970
Polythylene insulated and PVC sheathed (heavy duty) electric cables (Part
2) For working voltages from 3.3 kV up to and including 11 kV (withdrawn)
204
IS 5987:1970
Code of practice for selection of switches
[(voltage not exceeding 1000 V)-(withdrawn)]
205
IS 6160:1971
Rectangular conductors for electrical machines
206
IS 6209:1982
Methods for partial discharge measurement (first revision)
207
IS 6381:2004
Electrical apparatus for explosive gas atmospheres - Increased safety "e"
(first revision)
208
IS 6383:1971
Electric service lifts
209
IS 6390(Part 1):1983
Domestic electric clothes washing machines (first revision) (Superceded
by IS 14155:1994)
210
IS 6390(Part 3):1992
Domestic electrical clothes washing machines:
Part 3 Requirements for spin extractors
(Superseded by IS 14155:1994)
211
IS 6474:1984
Polyethylene insulation and sheath of electric cables (first revision)
212
IS 6538:1971
Three-pin plugs made of resilient material (Withdrawn)
213
IS 6539:1972
Intrinsically safe magneto telephones for use in hazardous atmospheres
214
IS 6585:1972
Screwless terminal and electrical connections for lighting fittings
[supersededby IS:10322(Part 3)]
215
IS 6600:1972
Guide for loading of oil immersed transformers (Withdrawn)
216
IS 6620:1972
Code of practice for installation, operation and maintenance of electric
service lifts
217
IS 6648:1972
Carbon electrodes for dry cells and batteries
218
IS 6789:1972
Bolted flameproof cable coupler and adaptors
219
IS 6875(Part 1):1973
Control switches(switching devices for control and auxiliary circuits
includingcontactor relays)for voltages upto and including 1000V ac &
1200V dc:
Part 1 General requirements
[superseded by IS 13947(Part 5/Section 1)]
220
IS 6875(Part 2):1973
Control switches(switching devices for control and auxiliary circuits
including contactor relays)for
voltages upto and including 1000V ac and 1200V dc:
Part 2Push-buttons and related control switches [Supresded by
IS13947(Part 5/Section1)]
221
IS 6875(Part 3):1980
Control switches(switching devices for control and auxiliary circuits
includingcontactor relays)for voltages upto and including 1 000 V ac and
1200 V dc :
Part 3 Rotary control switches
[superseded by IS 13947(Part 5/Section 1)]
222
IS 6946:1973
Flexible (pliable) non-metalic conduits for electrical installations
[Superseded by IS 9537(Part 5)]
223
IS 7013:1981
Radio dial lamps (first revision)
224
IS 7023:1973
Methods of tests for high pressure mercury vapour lamps [superseded by
IS 9900 (Part 1) to (Part 4)]
225
IS 7153:1973
Domestic electric controls for household
appliances (withdrawn)
Sl. No. IS Number/ DOC Number
Title
226
IS 7218:1974
Dry batteries for hearing aids
227
IS 7253:1974
Dry batteries for photoflash equipment
228
IS 7389:2004
Pressurized enclosures of electrical equipment for use in hazardous area
(second revision)(Superseded by IS/IEC 60079-2(2007)
229
IS 7389(Part 1):1976
Pressurized enclosures of eletrical apparatus for use in explosive
atmospheres: Part 1 Pressurized enclosures with no internal source of
flammable gas or vapour
(first revision)
230
IS 7404(Part 2):1991
Paper covered copper conductors : Part 2 Rectangular conductors (first
revision) (superseeding IS: 1666)
231
IS 7678:1975
Method of photometric testing of incandescent type luminaires for general
lighting service
232
IS 7693:2004
Electrical apparatus for explosive gas atmospheres - Oil immersion "o"
(first revision)
233
IS 7724:2004
Electrical Apparatus for explosive gas atmospheres - Powder filling 'q' (first
revision) (Superseded by IS/IEC 60079-5(2007)
234
IS 7733:1975
Code of practice for electrical wiring installations in hospitals (withdrawn)
235
IS 7759:1975
Lift door locking devices and contacts
236
IS 7820:2004
Electrical apparatus for explosive gas atmospheres - Method of test for
ignition temperatures (first revision)
237
IS 7987:1976
Guide for selection of high voltage
ac circuit breakers (withdrawn)
238
IS 8224:1976
Electric lighting fittings for division 2 areas
239
IS 8239:1976
Classification of maximum surface temperatures of electrical equipment
for use in explosive atmospheres (superseded by IS 13346:1992)
240
IS 8240:1976
Guide for electrical equipment for explosive atmosphere (superseded by
IS 13346:1992)
241
IS 8241:1976
Method of marking for identifying electrical equipment for explosive
atmospheres(superseded by IS 13346:1992)
242
IS 8264:1976
Air-drying and anti-tracking insulating varnishes for electrical purposes
[superseded by IS 10026 (Part 3)]
243
IS 8289:1976
Electrical equipment with type of protection 'n'
244
IS 8544(Part 1):1977
Motor starters for voltages not exceeding 1 000 V:
Part 1 Direction line ac starters
[superseded by IS 13947 (Part 4/Section 1):1993]
245
IS 8544(Part 2):1977
Motor starters for voltages not exceeding 1 000 V :
Part 2 Star-delta starters
[superseded by IS 13947 (Part 4/Section 1):1993]
246
IS 8544(Part 3/Sec
1):1979
Motor starters for voltages not exceeding 1000 V :
Part 3 Rheostatic motor starters,
Section 1 General requirements
[superseded by IS 13947 (Part 4/Section 1):1993]
247
IS 8544(Part 3/Sec
2):1979
Motor starters for voltages not exceeding 1 000 V:
Part 3 Rheostatic motor starters,
Section 2 Additional requirements
for ac rheostatic motor controllers
[superseded by IS 13947 (Part 4/Section 1):1993]
Sl. No. IS Number/ DOC Number
Title
248
IS 8544(Part 4):1979
Motor starters for voltages not exceeding 1 000 V:
Part 4 Reduced voltage ac starters: two step auto-transformer starters
[superseded by IS 13947 (Part 4/Section 1);1993]
249
IS 8603(Part 2):1977
Dimensions for porcelain transformer bushings for use in heavily polluted
atmospheres: Part 2 24 kV buhsings
250
IS 8603(Part 3):1977
Dimensions for porcelain transformer bushings for use in heavily polluted
atmospheres: Part 3 36 kV bushings
251
IS 8724:1978
Dimensions of carrier and bases used in rewirable fuses [superseded by
IS:2086]
252
IS 8783:1978
PVC insulated winding wires for submersible motors for 85 C operation
253
IS 8828:1996
Circuit-breakers for over current protection for
household and similar installations (second revision)
254
IS 9046:1978
AC contactors of voltage above 1000 V upto and including 11000 V
255
IS 9080(Part 3):1979
Safety requirements in electro-heat installations:
Part 3 Particular requirements for mains and
medium frequency induction furnace installations (Superseded by IS/IEC
60519-3:1988)
256
IS 9166:1979
Spark test apparatus for intrinsically safe circuits
257
IS 9224(Part 1):1979
Low voltage fuses: Part 1 General requirements
[superseded by IS 13703 (Part 1):1993]
258
IS 9224(Part 2):1979
Low voltage fuses: Part 2 Supplementary requirements for fuses for
industrial applications (superseding IS:2208) [superseded by IS 13703
(part 2/Section 1):1993]
259
IS 9224(Part 4):1980
Low voltage fuses: Part 4 Supplementary requirements for fuse-links for
the protection of semiconductor devices [superseded by IS 13703 (Part
4):1993]
260
IS 9299(Part 1):1979
Insulating materials based on built-up mica or treated mica paper: Part 1
Definitions and general requirements(Superseded by IS/IEC 603711:2003 )
261
IS 9299(Part 2):1992
Insulating materials based on built-up mica or treated mica paper: Part 2
Methods of test (first revision)(Superseded by IS/IEC 60371-2:2004 )
262
IS 9299(Part 3/Sec
1):1979
Insulating materials based on built-up mica or treated mica paper: Part 3
Specifications for individual materials, Section 1 Rigid mica material for
commutator separators (Superseded by IS/IEC 60371-3-1:2006 )
263
IS 9299(Part 3/Sec
2):1982
Insulating materials based on built-up mica or treated mica paper: Part 3
Specifications for individual materials, Section 2 Moulding mica materials
for electrical purposes (Superseded by IS/IEC 60371-3-9:1995 )
264
IS 9299(Part 3/Sec
3):1982
Insulating materials based on built-up mica or treated mica paper: Part 3
Specifications for individual materials, Section 3 Flexible mica flake tape
for insulation of electrical machines (Superseded by IS/IEC 60371-35:2005 )
265
IS 9299(Part 3/Sec
4):1982
Insulating materials based on built-up mica or treated mica paper: Part 3
Specifications for individual materials, Section 4 Rigid mica materials for
heating equipment (Superseded by IS/IEC 60371-3-3:1983 )
266
IS 9299(Part 3/Sec
5):1992
Insulating materials based on built up mica or treated mica paper: Part 3
Specification for individual materials,
Section 5, Flexible mica materials in sheet form (Superseded by IS/IEC
60371-3-3:1983 )
Sl. No. IS Number/ DOC Number
Title
267
IS 9299(Part 3/Sec
6):1993
Insulating materials based on built-up mica or treated mica paper: Part 3
Specifications for individual materials, Section 6 Glass backed mica paper
with
B-stage epoxy resin bond (Superseded by IS/IEC 60371-3-6:1992 )
268
IS 9299(Part 3/Sec
7):1992
Insulating materials based on built-up mica or treated mica paper: Part 3
Specification for individual material,
Section 7 Mica paper (Superseded by IS/IEC 60371-3-2:2005 )
269
IS 9570:1980
Classification of flammable gases or vapours with air according to their
maximum experimental safe gaps and minimum igniting currents
270
IS 9628:1980
Three-phase induction motors with type of protection 'n'Superseded by
IS/IEC 60079-15(2005)
271
IS 9735:2003
Electrical apparatus for explosive gas atmospheres - Flameproof
enclosures "d" Method of test for ascertainment of maximum experimental
safe gap
(first revision)
272
IS 9803:1981
Buffers for electric passenger and goods lifts
273
IS 9878:1981
Safety gears and governors for electric passenger and goods lifts
274
IS 10051:1981
PVC insulated winding wires for submersible motors for 105 degree
centrigrade operation
275
IS 10114:1982
Enamelled and varnish bonded glass covered rectangular copper wires
276
IS 10191:1982
Car and counterweight guide rails, guide rail supports and fastenings for
lifts
277
IS 10406:1983
Intrinsically safe transformers primarily for bell signalling circuits
278
IS 10448:1983
Retiring cam for electric passenger and goods lifts
279
IS 10452(Part 1):1983
Methods of tests for covered conductors for electrical equipment: Part 1
Paper covered and cotton covered conductors
280
IS 10452(Part 2):1983
Methods of tests for covered conductors for electrical equipment: Part 2
Fibrous covered conductors
281
IS 10542:1983
Safety requirements for refrigerators and
food freezers for household and similr purposes
[Superceded by IS 302(Part 2/Sec 24):1994]
282
IS 10810(Part 18):1984
Methods of test for cables:Part 18 Colour fastness to day light
283
IS 10913:1984
Brakes for electric passenger and goods lifts
284
IS 11005:1984
Dust tight ignition proof enclosures of electrical equipment
285
IS 11039:1983
Requirements for mounting on rails in switchgear and controlgear
installations (Sprseded by IS/IEC 60715:1981
286
IS 11349:1985
Oscilloscopes and peak voltmeters for impulse tests
287
IS 11426:1985
Specification for Alternating Current Precision Kilowatt-hour Meters of
Glass 0.5 for Testing Purposes
288
IS 11576:1986
Barlow's wheel
289
IS 11599:1986
Portable ac clip-on-ammeters
290
IS 11615:1986
Car and counterweight guide shoes for electric passenger and goods lifts
291
IS 11633:1986
Lift doors
292
IS 11706:1986
General requirements of car-frame for electric passangers and goods lift
293
IS 12155:1987
General and safety requirements for fans and
regulators for household and similar purposes
Sl. No. IS Number/ DOC Number
Title
294
IS 12315(Part 1):1988
Methods of determining the minimum ignition temperature of dusts: Part 1
Dust layer on a heated surface at a constant temperature (Superseded by
IS/IEC 61241-1(2000))
295
IS 12315(Part 2):1988
Methods of determining the minimum ignition temperature of dusts: Part 2
Dust cloud in a furnace at a constant temperature
296
IS 12661(Part 1):1988
High voltae motor-starter: Part 1 Direct-on-line
(full voltage) ac starters
297
IS 12729:2004
Common specification for high voltage switchgear and controlgear
standards (first revsion )
298
IS 12784(Part 1):1989
Electrical measuring transducers for converting ac electrical quantities into
dc electrical quantities- specification Part 1 General purpose transducers
299
IS 12788:1989
PVC covered wires overcoated with nylon for submerssible motors
300
IS 12802:1989
Temperature rise measurement of rotating electrical machines
(withdrawn)
301
IS 12819:1989
Transformer oil feed stock (TOFS) base stock (TOBS) (Withdrawn)
302
IS 12824:1989
Type of duty and classes of rating assigned to rotating electrical machines
(withdrawn)
303
IS 12956:1990
Sealed cylindrical type rechargeable nickel cadmium cells (tentative
standard withdrawn. Regular standrd being prepaired)
304
IS 12974:1990
Semiconductor contactors(Superceded by IS/IEC 60947-4-1:2000
305
IS 13118:1991
General requirements for circuit breakers
for voltages above 1 000 V (Superseding
all Parts and Sections of IS 2516)
306
IS 13340:1993
Shunt capacitors for the self-healing type for ac power systems having
rated voltage upto and including 650 V
307
IS 13346:2004
Electrical apparatus for explosive gas atmospheres - General
requirements(first revision)
308
IS 13408(Part 1):1992
Code of practice for the selection, installation and maintenance of
electrical apparatus for use in potentially explosive atmospheres(other
than mining application or explosive processing manufacture): Part 1
General recommendations(Superseded by IS/IEC 61241-14(2004))
309
IS 13573:1992
Joints and terminations for polymeric cables for working voltages from 6.6
kV up to and including 33 kV - performance requirements and type tests
310
IS 13947(Part 1):2004
Low-voltage switchgear and controlgear:
Part 1 General rules (superseding IS 2147 & 4237)
311
IS 13947(Part 2):1993
LV Switchgear and controlgear: Part 2 Circuit breakers (superseding IS
2516 & its parts)
312
IS 13947(Part 3):1993
Low-voltage switchgear and controlgear:
Part 3 Switches, disconnectors,switch-disconnectors
and fuse combination unit (superseding IS 4064 (part 1 &2)
313
IS 13947(Part 4/Sec
1):1993
Low-Voltage switchgear and controlgear: Part 4 Contactors and motor
starters,Section 1 Electromechanical contactors and motor
starters[superseding IS 2959 and 8544 (all parts)]
314
IS 13947(Part 5/Sec
1):2004
Low-voltage switchgear and controlgear:
Part 5 Control circuit devices and switching elements, Section 1
Electromechanical control circuit devices (first revision){Superseding IS
6875 (All parts)}
315
IS 13985:1994
Terminology for tools and equipment to be used in live
working(superceeded by IS 15416)
Sl. No. IS Number/ DOC Number
Title
316
IS 14154(Part 1):1996
Electrical apparatus with protection by enclosure for use in the presence of
combustible dusts: Part 1 Specification for apparatus (Superseded by
IS/IEC 61241-0(2004))
317
IS 14154(Part 2):1997
Electrical apparatus with protection by enclosure for use in presence of
combustible dust: Part 2 Guide to selection, installation and maintenance
(Superseded by IS/IEC 61241-14(2004))
318
IS 14390:1996
Var-hour meters, Class 3.0 [Superseding IS 722 (Part 6):1980]
319
IS 15451:2004
Electrical apparatus for explosive gas atmospheres - Encapsulation "m"
320
IS 60079(Part 20):1996
Electrical apparatus for explosive gas atmospheres : Part 20 Data for
flammable gases and vapours relating to the use of electrical apparatus
EQUIVALENT STANDARDS/DOCUMENTS
Sl. No. IS Number/ DOC Number
1
Title
DUAL NUMBER STANDARDS
DOC.ETD 23(6658)
ISO/IEC
IEC 61195 (2012)
Safety Specifications
2
DOC.ETD 23(6659)
Method of Measurement of Centre Beam
IEC/TR 61341 (2010)
Reflector Lamps
3
IS 1271:2012
Electrical Insulation - Thermal Evaluation
and designation (Second Revision)
IEC 60085 (2007)
4
IS 1401:2008
Protection of persons and equipment by
enclosures - Probes for verification
(second revision)
IEC 61032 : 1997
5
IS 1876:2005
Voltage measurement by means of
standard air gaps(first revision)
IEC 60052:2002
6
IS 1885(Part 9):1992
Electrotechnical Vocabulary: Part 9
Electrical relays (second revision)
IEC 60050(446):1983
7
IS 1885(Part 10):2008
Electrotechnical Vocabulary: Part 10
Power system protection (second revision)
IEC 60050(448):1995
8
IS 1885(Part 15):2008
Electrotechnical vocabulary: Part 15
Primary and secondary cells and batteries
(second revision) [Amalgamating IS
1885(Part 8):1986]
IEC 60050(482):2004
9
IS 1885(Part 27):2008
Electrotechnical Vocabulary: Part 27 Power IEC 60050(551):1998
electronics (Third Revision)
10
IS 1885(Part 28):1993
Electrotechnical vocabulary: Part 28
Instrument transformers (first revision)
IEC 60050(321):1986
11
IS 1885(Part 32):1993
Electrotechnical Vocabulary: Part 32
Electric cables (first revision)
IEC 60050(461):1984
12
IS 1885(Part 35):1993
Electrotechnical vocabulary: Part 35
Rotating machinery (first revision)
IEC 60050(411):1996
13
IS 1885(Part 37):1993
Electrotechnical vocabulary: Part 37 Tariffs IEC 60050(691):1973
for electricity (first revision)
14
IS 1885(Part 38):1993
Electrotechnical vocabulary: Part 38
Power transformers and reactors
(second revision)
IEC 60050(421):1990
15
IS 1885(Part 42):1993
Electrotechnical Vocabulary: Part 42
Power capacitors (second revision)
IEC 60050(436) :1990
16
IS 1885(Part 51):2012
Electrotechnical vocabulary: Part 51
IEC 60050-841:2004
Industrial electro-heating (Second Revision)
17
IS 1885(Part 54):1993
Electrotechnical Vocabulary: Part 54
Insulators (First revision)
18
IS 1885(Part 57):2008
Electrotechnical vocabulary: Part 57 Circuit IEC 60050(131):2002
Theory (Second Rrevision)
19
IS 1885(Part 60):1993
Electrotechnical Vocabulary: Part 60
Electrical apparatus for explosive
atmospheres (first revision)
IEC 60050(426):1990
20
IS 1885(Part 62):1993
Electrotechnical vocabulary: Part 62 Solid
insulating materials (first revision)
IEC 60050(212):1990
21
IS 1885(Part 69):1993
Electrotechnical Vocabulary: Part 69
Generation, transmission and distribution
of electricity - Generation
IEC 60050(602):1983
22
IS 1885(Part 70):1993
Electrotechnical Vocabulary: Part 70
Generation, transmission and distribution
of electricity - operation
IEC 60050(604):1987
IEC 60050(471):1984
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
23
IS 1885(Part 71):1993
Electrotechnical Vocabulary: Part 71
Generation, transmission and distribution
of electricity - Substations
IEC 60050(605):1983
24
IS 1885(Part 72):2008
Electrotechnical Vocabulary : Part 72
Mathematics (First Revision)
IEC 60050 (101):1998
25
IS 1885(Part 73):2012
Electrotechnical Vocabulary : Part 73
Physics and Chemistry [First Revision]
IEC 60050-111:1996
26
IS 1885(Part 74):2012
Electroechnical Vocabulary: Part 74
Electrical and magnetic devices(First
Revision)
IEC 60050(151): 2001
27
IS 1885(Part 75):2012
Electrotechnical Vocabulary: Part 75
Automatic control (First Revision)
IEC 60050-351 2006
28
IS 1885(Part 76):1993
Electrotechnical vocabulary: Part 76
Transducers
IEC 60050(431):1980
29
IS 1885(Part 77):1993
Electrotechnical Vocabulary: Part 77
Overhead lines
IEC 60050(466): 1990
30
IS 1885(Part 78):1993
Electrotechnical Vocabulary: Part 78
Genereation, transmission and distribution
of electricity - General
IEC 60050(601):1985
31
IS 1885(Part 79):1993
Electrotechnical Vocabulary: Part 79
Generation, transmission and distribution
of electiricity - Power system planning and
management
IEC 60050(603):1986
32
IS 1885(Part 80):1994
Electrotechnical vocabulary: Part 80
General terms on measurements in
electricity
IEC 60050(301):1983
33
IS 1885(Part 81):1993
Electrotechnical vocabulary: Part 81
Electrical measuring instruments
IEC 60050(302):1983
34
IS 2026(Part 3):2009
Power Transformers - Part 3 Insulaiton
levels, dielectric tests and external
clearances in air (third revision)
IEC 60076-3 (2000)
35
IS 2026(Part 7):2009
Power Transformers - Part 7 Loading
guide for oil immersed power transformers
IEC 60076-7(2005)
36
IS 2026(Part 8):2009
Power Transformers - Part 8 Application
guide
IEC 60076-8(1997)
37
IS 2026(Part 10):2009
Power Transformers - Part 10
Determination of sound levels
IS/IEC60076-10(2001)
38
IS 2071(Part 1):2014
High-voltage test techniques - Part 1:
General definitions and test requirements
(Third Revision).
IEC 60060-1: 2010
39
IS 2165(Part 5):2005
Insulation coordination:Part 5 Procedures
for high- voltage direct current (HVDC)
converter stations
IEC 60071-5:2002
40
IS 2824:2007
Method for the determination of the proof
and the comparative tracking indices of
solid insulating materials (second revision)
IEC 60112:2003
41
IS 2993:1998
A.C. motor capacitors (second revision)
IEC 60252:1993
42
IS 3427:1997
A.C. Metal enclosed switchgear and
controlgear for rated voltages above 1kV
upto and including 52 kV(first revision)
IEC 60298:1990
43
IS 5154(Part 1):2013
[IEC 60254-1(2005)
General requirements and methods of test
(Second Revision)
Sl. No. IS Number/ DOC Number
44
Title
IS 5154(Part 2):2013
ISO/IEC
[IEC 60254-2(2008)
Dimensions of cells and terminals and
marking of polarity on cells (Second
Revision)
45
IS 5825:1993
Test procedure for the determination of the IEC 60172(1987)
temperature index of enamelled winding
wires (first revision)
46
IS 6362:1995
Designation of methods of cooling of
rotating electrical machines
IEC 60034-6:1991
47
IS 6991:1985
Radiographic cassettes
IEC 60406(1975)
48
IS 8437(Part 1):1992
Guide on effects of current passing
through human body: Part 1General
aspects(first revision)
IEC 60479-1:1984
49
IS 8437(Part 2):1992
Guide on effects of current passing
through human body : Part 2 Special
aspects (first revision).
IEC 60479-2:1987
50
IS 8516:2011
IEC 60426(2007)
Determination of electrolytic corrosion
methods (First Revision)
51
IS 8623(Part 1):1993
Specification for low voltage switchgear
and controlgear assemblies:
Part 1 Requirements for type-tested
and partially type tested assemblies (first
revision).
IEC 60439-1(1985)
52
IS 8623(Part 2):1993
Specification for low voltage switchgear
and controlgear assemblies:
Part 2 Particular requirements for busbar
trunking systems (busways)-(first revision)
IEC 60439-2(1987)
53
IS 8623(Part 3):1993
Low-voltage switchgear and controlgear
assemblies:
Part 3 Particular requirements for
equipment where unskilled persons have
access for their use.
IEC 60439-3(1990)
54
IS 9335(Part 2):1998
Cellulosic papers for electrical purposes:
Part 2 Methods of test (superseding
IS:2188)
IEC 60554-2(2001)
55
IS 9348:1998
Coupling capacitor and capacitor dividers
IEC 60358:1990
56
IS 9835(Part 1):2001
Series capacitors for power systems:
Part 1 General performance testing and
ratingSafety requirements - guide for installation
(first revision)
IEC 60143-1:1992
57
* IS 9920(Part 1):2002
High Voltage Switches - Part 1 : Switches
for Rated Voltages Above 1 kV and Less
Than 52 KV
IEC 60265:1998
58
IS 9920(Part 2):2001
High voltage switches : Part 2 High voltage
switches for rated voltages of 52 kV and
above (First revision)
IEC 60265-2:1988
59
IS 9947:2011
Electrical Insulating materials used under
IEC 60587(2007)
for evaluating resistance to tracking and
erosion (First Revision)
60
IS 10189(Part 2/Sec
1):2000
Industrial process control valves Part2/Sec
1 Flow Capacity-sizing Equations for fluid
flow under Installed conditions
(superseding of IS 10189(Part 2/Sec
1):1992
IEC 60534-2-1:1998
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
61
IS 10593:2006
Mineral oil-impregnated electrical
equipment in service - Guide to the
interpretation of dissolved and free gases
analysis (second revision)
62
IS 11182(Part 5):1993
Guide for evaluation of insulation system of IEC 60941(1988)
electrical equipment: Part 5 Mechanical
endurance functional tests
63
IS 11298(Part 2):1999
Plastic films for electrical purposes: Part 2
Methods of test (first revision)
IEC 60674-2(1988)
64
IS 11298(Part 3/Sec
3):1998
Plastic films for electrical purposes:Part 3
Specifications for individual
materials,Section 3 Requirements for
balanced biaxially oriented Polyethylene
Terephalate(PET) films used for electrical
insulation
IEC 60674-3-2 (1992)
65
IS 11298(Part 3/Sec
4):1998
Plastic films for electrical purposes: Part 3
Specification for individual materials,
Section 4 Requirements for polycabonate
(PC) films used or electrical insulation
IEC 60674-3-3(1992)
66
IS 11298(Part 3/Sec
8):1998
Plastic films or electrical purposes: Part 3
Specification for individual materials,
Section 8 Requirements for fluoroethylene
(FEP) films used for electrical insulation
IEC 60674-3-7(1992)
67
IS 11298(Part 3/Sec 57):1998
Plastic Films for Electrical Purposes Part 3
Specification for Individual Materials
Section 5-7 Requirements for Polyimide
Films
IEC60674-3-4to6(1993
68
IS 12032(Part 1):1987
Graphical symbols for diagrams in the field
of electrotechnology: Part 1 General
information,general index,cross reference
table
IEC 60617-1(1985)
69
IS 12032(Part 2):1987
Graphical symbols for diagrams in the field
of electrotechnology: Part 2 Symbols
elements, qualifying symbols and other
symbols having general application
IEC 60617-2(1983)
70
IS 12032(Part 3):1987
Graphical symbols for diagrams in the field
of electrotechnology:Part 3 Conductors
and connecting devices
IEC 60617-3(1983)
71
IS 12032(Part 4):1987
Graphical symbols for diagrams in the field IEC 60617-4(1984)
of electrotechnology: Part 4 Passive
components
72
IS 12032(Part 6):1987
Graphical symbols for diagrams in the field IEC 60617-6(1983)
of electrotechnology: Part 6 Production and
conversion of electrical energy
73
IS 12032(Part 7):1987
Graphical symbols for diagrams in the field IEC 60617-7(1983)
of electrotechnology: Part 7 Switchgear,
controlgear and protective devices
74
IS 12032(Part 8):1987
Graphical symbols for diagrams in the field
of electrotechnology: Part 8 Measuring
instruments, lamps
and signalling devices
IEC 60617-8(1983)
75
IS 12032(Part 11):1987
Graphical symbols for diagrams in the field
of electrotechnology: Part 11 Architectural
and topographical installation plans and
diagrams
IEC 60617-11(1983)
IEC 60599(1999)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
76
IS 12640(Part 1):2008
Residual current operated circuit-breakers IEC 61008-1:1996
for household and simililar uses : Part 1
circuit-breakers without integral overcurrent
protection(RCCBs) (First Revision)
77
IS 12640(Part 2):2008
Residual current operated circuit breakers
for household and similar uses: Part 2
circuit breakers with integral overcurrent
protection(RCBOs) (First Revision)
IEC 61009-1:1996
78
IS 12672:1989
Internal fuses and internal overpressure
disconnectors for shunt capacitors
IEC 60593:1977
79
IS 12747(Part 1):2011
Combined flexible materials for electrical
insulation - Part 1 Definition and general
requirements (First Revision )
IEC 60626-1(2009)
80
IS 12747(Part 2):2012
Combined flexible materials for electrical
insulation - Part 2 Method of test (First
Revision)
IEC 60626-2:2012
81
IS 12747(Part 3):2014
Combined flexible materials for electrical
insulation - Part 3: Specifications for
individual materials (First Revision)
IEC 60626-3:2008
82
IS 12762(Part 1):2010
Photovoltaic devices: Part 1 Measurement
of photovoltaic current-voltage
characteristics
[first revision)
IEC 60904-1:2006
83
IS 12762(Part 2):2013
Photovoltaic devices: Part 2 Requirements
for reference solar cells (First Revision of
IS 12762 (Part 2))
IEC 60904-2 (2007)
84
IS 12762(Part 3):2013
Photovoltaic devices Part 3 Measurement
principles for terrestrial (PV) solar devices
with reference spectral irradiance data
(First Revision of IS 12762 (Part 3)
IEC 60904-3 (2008)
85
IS 12762(Part 5):2010
Photovoltaic devices: Part 5 Determination IEC 60904-5:1993
of the
equivalent cell temperature (ECT) of
photovoltaic (PV) devices by the opencircuit voltage method
86
IS 12762(Part 7):2013
Photovoltaic devices: Part 7 Computation
of spectral mismatch error introduced in
the testing of a photovoltaic device
87
IS 12762(Part 8):2010
Photovoltaic devices: Part 8 Measurement IEC 60904-8:1998)
of spectral response of a photovoltaic (PV)
device
88
IS 12762(Part 9):2010
Photovoltaic devices: Part 9 Solar
simulator performance requirments
IEC 60904-9:2007
89
IS 12762(Part 10):2010
Photovoltaic devices: Part 10 Methods of
linearity measurment
IEC 60904-10:1998
90
IS 12998(Part 1):1991
Method f measurement of airborne noise
emitted by rotating machinery: Part 1
Engineering method for free field
conditions over a reflecting plane
ISO 1680-1:1986
91
IS 12998(Part 2):1991
Method of measurement of airborne noise
emitted by rotating machinery: Part 2
Survey method
ISO 1680-2:1986
92
IS 13107:1991
Guide for measurement of winding
resistance of an ac machine during
operation at alternating voltage
IEC 60279(1969)
IEC 60904-7 (2008 )
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
93
IS 13234:1991
Guide for short circuit current
calculations ln three-phase ac
systems(superseding IS 5728)
IEC 60909:1988
94
IS 13235:1991
Calculation of the effects of short-circuit
currents Superseding IS 5728:1970)
IEC 60865:1986
95
IS 13465(Part 1):2005
Resin based reactive compounds used for
electrical insulation: Part 1 Definitions and
general requirements (first revision)
IEC 60455-1(1998)
96
IS 13465(Part 2):2005
Resin based reactive compounds used for
electrical insulation: Part 2 Methods of test
[first revision]
IEC 60455-2(1998)
97
IS 13465(Part 3/Sec
1):2006
Resin based reactive compounds used for
electrical insulation - Part 3: Specification
for individual materials - Section 1: Unfilled
epoxy resinous compounds (first revision)
IEC 60455-3-1(2003)
98
IS 13465(Part 3/Sec
2):2006
Resin based reactive compounds used for
electrical insulation - Part 3: Specification
for individual materials - Section 2: Quartz
filled epoxy resinous compounds [first
revision)
IEC 60455-3-2
99
IS 13465(Part 3/Sec
3):2006
Resin based reactive compounds used for
electrical insulation - Part 3: Specification
for individual materials - Section 3: Unfilled
polyurethane compounds [first revision)
IEC 60455-3-3
100
IS 13465(Part 3/Sec
4):2006
Resin based reactive compounds used for
electrical insulation - Part 3: Specification
for individual materials - Section 4: Filled
polyurethane compounds (first revision)
IEC 60455-3-4
101
IS 13465(Part 3/Sec
6):2006
Resin based reactive compounds used for
electrical insulation - Part 3: Specification
for individual materials - Section 6:
Unsaturated polyester based impregnating
resins
IEC 60455-3-5(2001)
102
IS 13503:2013
Classification of insulating liquids (First
Revision)
IEC 61039:2008
103
IS 13514:2014
Secondary batteries (except lithium) for the IEC 61982:2012
propulsion of electric road vehicles Performance and endurance tests (First
Revision)
104
IS 13516:1993
Methods of synthetic testing of high voltage IEC 60427:1989
alternating current circuit breakers
105
IS 13588:1993
Spring operated impact test apparatus and
calibration
IEC 60817(1984)
106
IS 13703(Part 1):1993
Low voltage Fuses for voltages not
exceeding 1000 V ac or 1500 V dc: Part 1
General requirements [superseding IS
9224 (Part 1):1979]
IEC 60269-1(1986)
107
IS 13703(Part 2/Sec
1):1993
Low voltage fuses for voltages not
exceeding
1000 V ac or 1500 V dc: Part 2 Fuses for
use by authorized persons, Section 1
Supplementary requirements [superseding
IS 9224 (Part 2):1979]
IEC 60269-2(1986)
108
IS 13703(Part 2/Sec
2):1993
Low voltage fuses for voltages not
exceeding
1000 V ac or 1500 V dc: Part 2 Fuses for
use by authorized persons, Section 2
Examples of standardized fuses
IEC 60269-2-1(1987)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
109
IS 13703(Part 4):1993
Low voltage fuses for voltages not
IEC 60269-4(1986)
exceeding 1000 V ac or 1500 V dc: Part 4
Supplementary requirements for fuse- links
for the protectlon of semiconductor devices
[superceding IS 9224 (Part 4):1980]
110
IS 13730:2012
Specifications for particular types of
winding wires: Part 0 General
requirements, Section 1 Enamelled round
copper wire (First Revision)
IEC 60317-0-1:2008
111
IS 13730(Part 0/Sec
2):2011
Specifications for particular types of
winding wires: Part 0 General
requirements, Section 2 Enamelled
rectangular copper wire (First Revision)
IEC 60317-0-2:2005
112
IS 13730:2012
Specifications for particular types of
winding wires Part 0-3: General
IEC 60317-0-3:2008
aluminium wire [First Revision of IS
13730 (Part 0/Sec 3):1994] I
113
IS 13730(Part 0/Sec
4):2011
Specifications for particular types of
winding wires: Part 0 General
requirements, Section 4 Glass fibre wound
resin of varnish impregnated bare or
enamelled rectangular copper wire (First
Revision)
IEC 60317-0-4:2006
114
IS 13730(Part 0/Sec
5):2012
Specifications for particular types of
winding wires: Part 0 General
requirements, Section 5 glass fibre
braided, bare or enamelled rectangular
copper wire (First Revision)
IEC 60317-0-5(2006)
115
IS 13730(Part 1):1993
Specifications for particular types of
winding wires: Part 1 Polyvinyl acetal
enamelled round copper wire, class 105
[superseeds IS 4800(Part 4):1968]
IEC 60317-1(1990)
116
IS 13730(Part 2):2012
Specifications for particular types of
winding wires Part 2: Solderable
polyurethane enamlled round copper wire,
class 130, with a bonding layer. (First
Revision)
IEC 60317-2 : 2000
117
IS 13730(Part 3):2013
Specifications for particular types of
IEC 60317-3:2004
winding wires Part 3 polyester enamelled
round copper wire, class 155 (first revision)
118
IS 13730(Part 4):2013
Specifications for particular types of
IEC 60317-4(1990)
winding wires: Part 4 Solderable
polyurethane enamelled round copper wire,
class 130 (first revision)
119
IS 13730(Part 7):1993
Specifications for particular types of
winding wiresC Part 7 Polyimide
enamelled round copper wire Class 220
[superseeds IS 4800(Part 11):1981]
IEC 60317-7(1990)
120
IS 13730(Part 8):1996
Specifications for particular types of
winding wires: Part 8 polyesterimide
enamelled round copper wire class 180
IEC 60317-8(1990)
121
IS 13730(Part 12):2012
Specifications for particular types of
winding wires Part 12: Polyvinyl acetal
enamelled round copper wire, class 120
IEC 60317-12:2010
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
122
IS 13730(Part 13):2014
Specifications for particular types of
winding wires: Part 13 Polyester or
polyesterimide overcoated with polyamideimide enamelled round copper wire, Class
200
IEC 60317-13(1990)
123
IS 13730(Part 16):1996
Specifications for particular types of
winding wires: Part 16 Polyester
enamelled rectangular copper wire, Class
155
IEC 60317-16 (1990)
124
IS 13730(Part 17):2014
Specifications for particular types of
winding wires: Part 17 Polyvinyl acetal
enamelled rectangular copper wire, Class
105
IEC 60317-17 (1990)
125
IS 13730(Part 20):2014
Specifications for particular types of
IEC 60317-20(1990)
winding wires: Part 20 Solderable
polyurethane enamelled round copper wire,
Class 155
126
IS 13730(Part 26):1996
Specifications for particular types of
winding wires: Part 26 Polyamide-imide
enamelled round copper wire, Class 200
IEC 60317-26 (1990)
127
IS 13730(Part 27):1997
Specifications for particular types of
winding wires: Part 27 Paper covered
rectangular copper wire
IEC 60317-27(1990)
128
IS 13730(Part 28):1997
Specifications for particular types of
winding wires: Part 28 Polyesterimide
enamelled rectangular copper wire, Class
180
IEC 60317-28(1990)
129
IS 13730(Part 29):1996
Specifications for particular types of
winding wires: Part 29 Polyester or
polyesterimide overcoated with polyamideimide enamelled rectangular copper wire,
Class 200
IEC 60317-29(1990)
130
IS 13730(Part 31):1997
Specifications for particular types of
winding wires: Part 31 Glass-fibre wound,
polyester or polyesterimide varnishtreated, bare or enamelled rectangular
copper wire, temperature index 180
IEC 60317-31(1990)
131
IS 13730(Part 32):1997
Specifications for particular types of
IEC 60317-32(1990)
winding wires: Part 32 Glass-fibre wound,
polyester or polyesterimide varnish-treated,
bare or enamelled rectangular copper wire,
temperature index 155
132
IS 13730(Part 33):1997
Specifications for particular types of
winding wieres: Part 33 Glass-fibre
wound, silicone varnish-treated bare or
enamelled rectangular copper wire,
temperature index 200
IEC 60317-33 (1990)
133
IS 13730(Part 34):2000
Specifications for particular types of
winding wires: Part 34 Polyester
enamelled round copper wire, Class 130
(first revision)
IEC 60317-34(1997)
134
IS 13730(Part 39):2005
Specifications for particular types of wires:
Part 39 Glass-fibre braided polyester or
polyesterimide varnish-treated, bare or
enamelled rectrangular copper wire,
temperature index 180
IEC 60317-39:1992
135
IS 13730(Part 43):2013
Specifications for particular types of wires: IEC 60317-43:1997
Part 43 Aromatic polyimide tape wrapped
round copper wire, class 240 (first revision)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
136
IS 13730(Part 44):2013
Specifications for particular types of wires:
Part 44 Aromatic polyimide tape rapped
rectangular copper wire, class 240 (first
revision)
IEC 60317-44:1997
137
IS 13730(Part 48):2005
Specifications for particular types of wires:
Part 48 Glass fibre wound resin or varnish
impregnated bare or enamelled round
copper wire, temperature index 155
IEC 60317-48:1999
138
IS 13730(Part 49):2005
Specifications for particular types of wires:
Part 49 Glass fibre wound resin or varnish
impregnated bare or enamelled round
copper wire, temperature index 180
IEC 60317-49:1999
139
IS 13730(Part 50):2005
Specifications for particular types of wires:
Part 50 Glass fibre wound resin or varnish
impregnated bare or enamelled round
copper wire, temperature index 200
IEC 60317-50:1999
140
IS 13730(Part 53):2005
Specifications for particular types of wires: IEC 60317-53:1999
Part 53 Aromatic polyamide (aramid ) tape
wrapped rectangular copper wire,
temperature index 220
141
* IS 13772:1993
Hand tools for live working up to 1000 V ac IEC 60900:1989
and 1500 V dc
142
IS 13773:1993
Sleeves of insulating material for live
working
IEC 60984:1990
143
IS 13778(Part 1):2011
Methods of tests for winding wires: Part 1
General (First Revision)
IEC 60851-1:1996
144
IS 13778(Part 2):2013
Methods of tests for winding wires: Part 2
Determination of dimensions (First
Revision)
IEC 60851-2:2009
145
IS 13778(Part 3):2012
IEC 60851-3:2009
Mechanical properties [First Revision of IS
13778 (Part 3)
146
IS 13778(Part 4):2011
147
IS 13778(Part 5):2012
Methods of tests for winding wires: Part 4
Chemical properties
IEC 60851-4:2005
IEC 60851-5 : 2008
Electrical properties [First Revision of IS
13778 (Part 5)
148
IS 13778(Part 6):2011
Methods of tests for winding wires: Part 6
Thermal properties (First Revision)
IEC 60851-6:1996
149
IS 13925(Part 2):2002
Shunt capacitors for ac power systems
having a rated voltage above 1000 V : Part
2 Endurance testing (first revision)
IEC60871-2:1999
150
IS 13925(Part 3):2002
Shunt capacitors for ac power systems
having a rated voltage above 1000 V: Part
3 Protection of shunt capacitors and shunt
capacitors banks.
IEC 60871-3:1996
151
IS 13937(Part 1):1994
Statistical method of determining and
ISO 7574-1:1985
verifying standard noise emission values of
machinery and equipment: Part 1 General
conditions and definitions
152
IS 13937(Part 2):1994
Statistical method of determining and
ISO 7574-2:1985
verifying standard noise emission values of
machinery and equipment: Part 2 Methods
of stated values for individual machines
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
153
IS 13937(Part 3):1994
Statistical method of determining and
ISO 7574-3:1985
verifying standard noise emission values of
machinery and equipment: Part 3 Simple
(transition) method for stated values for
batches of machines
154
IS 13937(Part 4):1994
Statistical method of determining and
ISO 7574-1985
verifying standard noise emission values of
machinery and equipment: Part 4 Methods
for stated values for batches of machines
155
IS 13947(Part 5/Sec
2):2004
Low voltage switchgear and controlgear :
Part 5 Control circuit devices and
switching elements Section 2 Proximity
switches
IEC 60947-5-2(2000)
156
IS 13961:1994
Insulating poles (insulating sticks) and
universal tool attachments (fittings) for live
working
IEC 60832:1988
157
IS 14195:1994
Brush-holders for electrical machines
guide to the measurement of the static
thrust applied to brush
IEC 61015(1990)
158
IS 14196:1994
Definitions and terminology of brushholders for electrical machines
IEC 60560(1977)
159
IS 14197:1994
Code for model acceptance tests of
hydraulic turbines
IEC 60193:1965
160
IS 14198(Part 1):1994
Rules for steam turbines thermal
acceptance tests - Method A
IEC 60953-1:1990
161
IS 14198(Part 2):1994
Rules for steam turbines thermal
acceptance tests - Method B
IEC 60953-2:1990
162
IS 14205(Part 1):1994
Steam turbines Part 1 Specification
IEC 60045-1:1991
163
IS 14222:1995
Impulse withstand levels of rotating ac
machines with form wound stator coils
IEC 60034-15:1990
164
IS 14244:1995
Characteristic parameters of stand alone
photovoltaic (PV) systems
IEC 61194(1992)
165
IS 14254(Part 1):2003
Programmable controller: Part 1 General
information
(first revision)
IEC 61131-1(2003)
166
IS 14254(Part 2):2003
Programmable Controllers: Part 2
Equipment Requirements and Tests (first
revision)
IEC 61131-2(2003)
167
IS 14286:2010
Crystalline silicon terrestrial photovoltaic
(PV) modules - Design qualiication and
type approval
(first revision)
IEC 61215:2005
168
IS 14568(Part 2):1998
Dimensions and output series for rotating
electrical machines Part 2 Frame numbers
355 to 1000 and flange numbers 1180 to
2360
IEC 60072-2(1990)
169
IS 14570:2012
Electrical measuring transducers for
converting AC electrical quantities to to
analogue or digital signals
IEC 60688:1992
170
IS 14571:1998
Electrical measuring Instruments X-Y
recorders.
IEC 61028(1991)
171
IS 14577:1998
Short-circuit current evaluation with special IEC 60363(1998)
regard to rated short-circuit capacity of
circuit-breakers in installations in ships
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
172
IS 14614:1998
Residual Current Operated Protective
Devices (RCDs) for household and similar
use - Electromagnetic compatibility.
IEC 61543(1995)
173
IS 14657:1998
Gas-insulated metal-enclosed switchgear
for rated voltage 72.5 kV and above requirements for switching of bus-charging
current by disconnectors.
IEC 61259:1994
174
IS 14658:1999
High-voltage alternating current circuitbreakers- Guide for short-circuit and
switching test procedures for metalenclosed and dead tank circuit-breakers
IEC 61633:1995
175
IS 14659:1999
A.C. insulation-enclosed switchgear and
controlgear for rated voltage above 1 kV
and upto and including 38 kV
IEC 60466:1987
176
IS 14666:1999
High voltage alternating current switch fuse IEC 60420:1990
combinations
177
IS 14674:1999
High voltage alternating current circuit
breakersGuide for seismic qualifications of highvoltage alternating current circuit-breakers
IEC 61166:1993
178
IS 14786:2000
High voltage/ low voltage prefabricated
substations
IEC 61330:1995
179
IS 14801:2000
Terminology for high voltage direct
current ( HVDC ) transmission.
IEC 60633(1998)
180
IS 14841(Part 2/Sec
1):2000
Packaging of winding wires: Part 2
IEC 60264-2-1:1989
Cylindrical barrelled delivery spools Section
1 Basic dimensions
181
IS 14841(Part 2/Sec
2):2000
Packaging of winding wires: Part 2
Cylindrical barrelled delivery spools,
Section 2 Specification for returnable
spools made from thermoplastic material
IEC 60264-2-2:1990
182
IS 14841(Part 3/Sec
1):2000
Packaging of winding wires: Part 3 Taper
barrelled delivery spools, Section 1 basic
dimensions
IEC 60264-3-1:1999
183
IS 14841(Part 3/Sec
2):2000
Packaging of winding wires: Part 3 Taper
barrelled delivery spools, Section 2
Specification for returnable spools made
from thermoplastic material
IEC 60264-3-2:1999
184
IS 14841(Part 3/Sec
3):2000
Packaging of winding wires: Part 3 Taper
barrelled delivery spools, Section 3
Specification for non-returnable spools
made from thermoplastic material
IEC 60264-3-3:1990
185
IS 14841(Part 3/Sec
4):2000
Packaging of winding wires: Part 3 Taper
barrelled delivery spools, Section 4 basic
dimensions of containers for taper
barrelled delivery spools
IEC 60264-3-4:1999
186
IS 14841(Part 4/Sec
1):2013
Packaging of winding wires: Part 4
Methods of test, Section 1 Delivery spools
made from thermoplastic material (first
revision)
IEC 60264-4-1:1997
187
IS 14911(Part 1):2001
Thyristor valves for high-voltage direct
IE 60700-1(1998)
current (HVDC) power transmission: Part 1
Electrial Testing
188
IS 14957:2001
Aerial devices with insulating boom used
for live working
IEC 61057:1991
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
189
IS 14981:2001
Live working - Earthing or earthing and
short-circuiting equipment using lances as
a short-circuiting device - lance earthing
IEC 61219:1993
190
IS 14993:2001
Saddles, pole clamps (stick clamps) and
accessories for live working
IEC 61236:1993
191
IS 15086(Part 1):2001
Surge arresters: Part 1 Non-linear resistor
type gapped
surge arresters for a.c. systems
[Superseding IS 3070(Part 1)]
IEC 60099-1:1991
192
IS 15086(Part 5):2001
Surge arresters : Part 5 Selection and
application recommendations
(Superseading IS 4004)
IEC 60099-5:1996
193
IS 15199(Part 1):2002
Power convertors: installed on board
IEC 61287-1(1995)
railway rolling stock - Part 1 Characteristics
and test methods
194
IS 15199(Part 2):2002
Power convertors: installed on board
railway rolling stock - Part 2 Additional
technical information
195
IS 15382(Part 1):2003
Insulation coordination for equipment
IEC 60664-1(2002)
within low voltage system: Part 1 Principles
requirements and test
196
IS 15382(Part 2/Sec
1):2003
Insulation coordination for equipment
within low voltage system : Part 2
Appication guide, Section 1 Dimensioning
procedure worksheets and dimensioning
examples
IEC 60664-2-1(1977)
197
IS 15382(Part 3):2006
Insulation coordination for equipment
within low voltage system: Part 3 Use of
coatings, potting or moulding for protection
against pollution
IEC 60664-3(2003)
198
IS 15395:2003
Industrial ac net- work affected by
harmonicsapplication of filters and shunt capacitors
IEC 61642 :1997
Live Working - flame resistance materials
for clothing for thermal protection of
working thermal hazards of an electric arc
Part 1 Test Methods
IEC 61482-1:2002
IEC 61287-2(2001)
199
* IS 15405(Part 1):2003
200
IS 15406(Part 1):2003
Capacitors for microwave ovens: Part 1
General
IEC 61270-1:1996
201
IS 15407:2003
Live working - Guidelines for dielectric
testing of tools and equipment
IEC 61278:1997
202
IS 15416:2003
Live working - Terminology for tools
equipments and devices (Superceding IS
13985)
IEC 60743:2001
203
IS 15597:2005
Determination of power losses in high
voltage direct current (HVDC) converter
stations
IEC 61803:1999
204
IS 15617:2005
Power electronics for electrical
transmission and distribution systemsTesting of thyristor valves for static var
compensations
IEC 61954:2003
205
IS 15638(Part 1):2006
Instruments and software used for
IEC 61083-1(2001)
measurement in high voltage impluse
tests: Part 1 Requirements for instruments(
Superseeding IS 11349)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
206
IS 15638(Part 2):2006
Instruments and software used for
measurements in high voltage impulse
tests: Part 2 Evaluation of software used
for the determination of the parameters of
impulse waveforms (Superseeding IS
11349)
IEC 61083-2(1996)
207
IS 15644:2006
Safety of electric toys
IEC 62115(2003)
208
IS 15664:2006
Gas turbines - Acceptance tests
ISO 2314(1989)
209
IS 15665:2006
Gas turbines - Vocabulary
ISO 11086(1996)
210
IS 15666(Part 1):2006
Gas turbines - Procurement - Part 1:
General introduction and definitions
ISO 3977-1(1997)
211
IS 15666(Part 2):2006
Gas turbines - Procurement - Part 2:
Standard reference conditions and ratings
ISO 3977-2(1997)
212
IS 15666(Part 3):2006
Gas turbines - Procurement - Part 3:
Design requirements
ISO 3977-3(2004)
213
IS 15666(Part 4):2006
Gas turbines - Procurement - Part 4: Fuels
and environment
ISO 3977-4(2002)
214
IS 15666(Part 5):2006
Gas turbines - Procurement - Part 5:
Applications for petroleum and natural gas
industries
ISO 3977-5(2001)
215
IS 15666(Part 7):2006
Gas turbines - Procurement - Part 7:
Technical information
ISO 3977-5(2002)
216
IS 15666(Part 8):2006
Gas turbines - Procurement - Part 8:
Inspection, testing, installation and
commissioning
ISO 3977-8(2002)
217
IS 15666(Part 9):2006
Gas turbines - Procurement - Part 9:
Reliability, availability, maintainability and
safety
ISO 3977-9(1999)
218
IS 15667:2006
Gas turbines - Data acquisition and trend
monitoring system requirements for gas
turbine installations
ISO 19860(2005)
219
IS 15668:2006
Mineral insulating oils - Methods for the
determination of 2-furfural and related
compounds
IEC 61198(1993)
220
IS 15767:2008
Secondary Cells and Batteries Containing
IEC 62259:2003
Nickel-Cadmium Prismatic Secondary
Single Cells with Partial Gas Recombination
221
IS 15885(Part 2/Sec
13):2012
Lamp Control gear Part 2 Particular
Requirements. Section 13 D.C. or A.C.
Supplied Electronic Controlgear For Led
Modules
222
IS 15906:2010
Measurement of mercury level in
fluorescent lamps
223
* IS 16046:2012
Secondary cells and batteries containing
IEC 61347-2-13(2006)
IEC 62133(2002)
Safety requirements for portable sealed
secondary cells, and for batteries made
from them, for use in portable applications
224
IS 16047:2012
Secondary cells and batteries containing
Secondary lithium cells and batteries for
portable applications
IEC 61960 (2011)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
225
IS 16048(Part 1):2013
Secondary cells and batteries containing
IEC 61951-1:2006
alkaline or other non-acid electrolytes -Portable sealed rechargeable single cells -Part 1: nickel-cadmium
226
IS 16048(Part 2):2013
Secondary cells and batteries containing
alkaline or other non-acid electrolytes Portable sealed rechargeable single cells Part 2: nickel-metal hydride
IEC 61951-2:2011
227
IS 16049:2013
Secondary cells and batteries containing
IEC 60622:2002
Sealed nickel-cadmium prismatic
Rechargeable single cells
228
IS 16077:2013
Thin-film terrestrial photovoltaic (PV)
modules Design qualification and type approval
IEC 61646 (2008 )
229
IS 16081:2013
Insulating liquids - Specifications for
unused synthetic organic esters for
electrical purposes
IEC 61099:2010
230
IS 16085:2013
IS 16085:2013 Mineral oil-filled electrical
analysis (DGA) to factory tests on electrical
equipment
231
IS 16086:2013
dielectric dissipation factor by
measurement of the conductance and
232
IS 16099:2013
Synthetic organic esters for electrical
transformer esters in equipment
233
IS 16108:2012
Photobiological Safety of Lamp and Lamp
Systems
IEC 62471 (2006)
234
IS 16197(Part 1):2014
Determination of certain substances in
electrotechnical products : Part 1
Introduction and overview
IEC 62321-1:2013
235
IS 16197(Part 2):2014
Determination of certain substances in
IEC 62321-2:2013
Disassembly, disjointment and mechanical
sample preparation
236
IS 16197(Part 3/Sec
1):2014
Determination of Certain Substances in
Electrotechnical Products Part 3
Screening Section 1 Lead, Mercury,
Cadmium, Total Chromium and Total
Bromine Using X-Ray Fluorescence
Spectrometry
IEC 62321-3-1:2013
237
IS 16197(Part 3/Sec
2):2014
IS 16197 (Part 3/Section 2) : 2014
Determination of Certain Substances in
Electrotechnical Products Part 3
Screening Section 2 Total Bromine in
IEC 62321-3-2:2013
ION Chromatography
238
IS 16197(Part 4):2014
IS 16197 (Part 4) : 2014 Determination of
Certain Substances in Electrotechnical
Products Part 4 Mercury in Polymers,
Metals and Electronics by CV-AAS, CVAFS, ICP-OES and DICP-MS
IEC 62321-4:2013
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
239
IS 16197(Part 5):2014
Determination of Certain Substances in
IEC 62321-5:2013
Electrotechnical Products Part 5 Cadmium,
Lead and Chromium in Polymers and
Electronics and Cadmium and Lead in
Metals by AAS, AFS, ICP-OES and ICP-MS
240
IS 16220(Part 1):2014
General purpose lead-acid batteries (valve- IEC 61056-1:2012
regulated types) - Part 1: General
requirements, functional characteristics Methods of test
241
IS 60034(Part 1):2004
Rotating electrical machines - Part 1
Rating and performance
IS/IEC 60034-1(2004)
242
IS 60034(Part 5):2000
Rotating electrical machines - Part 5:
Degrees of protection provided by the
integral design of rotating electrical
machines (IP code) - Classification
(Superseding IS 4691)
IS/IEC 60034-5(2000)
243
IS 60034(Part 8):2002
Rotating electrical machines - Part 8:
IS/IEC 60034-8(2002)
Terminal markings and direction of rotation
(Superseding IS 4728)
244
IS 60041:2000
Field acceptance tests to determine the
hydraulic performance of turbines, storage
pumps and pump turbines
IS/IEC 60041(2000)
245
IS 60044(Part 1):2003
Instrument transformers: Part 1 Current
transformers
IS/IEC 60044-1(2003)
246
IS 60060(Part 2):2010
High voltage test techniques - Part 2
Measuring systems (IEC 60060-2:2010)
IS/IEC 60060-2:2010
247
IS 60071(Part 4):2004
Insulation coordination - Part 4:
Computational guide to insulation coordination and modelling of electrical
networks
IS/IEC 60071-4:2004
248
IS 60071(Part 1):2006
Insulation Coordination - Part 1 Definitions, IS/IEC 60071-1:2006
parinciples and rules
249
IS 60071(Part 2):1996
Insulation Coordination - Part 2 Application
guide (IEC 60071-2:1996)
IS/IEC 60071-2:1996
250
IS 60079:2007
Explosive Atmospheres. Part 0:
Equipment - General Requirements (First
Revision)
IS/IEC 60079-0:2007
251
IS 60079(Part 1):2007
Explosive atmospheres : Part 1 Equipment IS/IEC 60079-1:2007
protection by flameproof enclosures "d"
(superseding IS 2148:2004 )
252
IS 60079(Part 2):2007
Explosive atmospheres: Part 2 Equipment
protection by pressurized enclosure "p"
(superseding IS 7389:2004)
IS/IEC 60079-2:2007
253
IS 60079(Part 26):2006
Explosive Atmospheres Part 26
Equipment With Equipment Protection
Level EPL "Ga"
IS/IEC 60079-26:2006
254
IS 60079(Part 27):2013
Explosive Atmospheres Part 27 Fieldbus
Intrisically Safe Concept (FISCO)
IS/IEC 60079-27:2013
255
IS 60079(Part 5):2007
Explosive atmospheres: Part 5 Equipment
protection by powder filling "q"
(superseding IS 7724:2004)
IS/IEC 60079-5:2007
256
IS 60079(Part 6):2007
Explosive atmospheres: Part 6 Equipment
protection by oil immersion "o"
(superseding IS 7693:2004)
IS/IEC 60079-6:2007
257
IS 60079(Part 7):2006
Explosive atmospheres: Part 7 Equipment
protection by increased safety "e"
(superseding IS 6381:2004)
IS/IEC 60079-07:2006
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
258
IS 60079(Part 11):2006
Explosive atmospheres: Part 11
Equipment protection by intrinsic safety "i"
(superseding IS 5780:2002)
IS/IEC 60079-11:2006
259
* IS 60079(Part 15):2005
Electrical apparatus for explosive gas
atmospheres : Part 15 Construction, test
and marking of type of protection "n"
electrical apparatus (superseding
IS 8289)
IS/IEC 60079-15:2005
260
IS 60079(Part 16):1990
Electrical apparatus for explosive gas
atmospheres: Part 16 Artificial ventilation
for the protection of analyzer(s) houses
IS/IEC 60079-16:1990
261
IS 60079(Part 17):2007
Explosive atmospheres : Part 17
Electrical installations inspection and
maintenance
IS/IEC 60079-17:2007
262
IS 60079(Part 18):2009
Explosive Atmospheres Part 18
Equipment Protection By Encapsulation
"m" (First Revision)
IS/IEC 60079-18:2007
263
* IS 60079(Part 19):2006
Explosive atmospheres : Part 19 Repair,
overhaul and reclamation
IS/IEC 60079-19:2006
264
IS 60079(Part 20/Sec
1):2000
Explosive Atmospheres Part 20 material
Characteristics For Gas and Vapour
Classification Section 1 Test Methods and
Data(Superseding IS 7820, IS 9570, IS
9735, IS/IEC 60079-20)
IS/IEC60079-20-1:00
265
* IS 60079(Part 25):2003
Electrical apparatus for explosive gas
atmospheres : Part 25 Intrinsically safe
systems
IS/IEC 60079-25:2003
266
IS 60079(Part 28):2000
Explosive Atmospheres Part 28 Protection IS/IEC 60079-28:2000
of Equipment And Transmission Systems
Using Optical Radiation
267
IS 60079(Part 29/Sec
1):2007
Explosive atmospheres - Part 29-1: Gas
detectors - Performance requirements of
detectors for flammable gases
IS/IEC 60079-29-1:07
268
IS 60079(Part 29/Sec
2):2007
Explosive atmospheres - Part 29-2: Gas
detectors - selection, installations, use and
maintenance of detectors for flammable
gases and oxygen
IS/IEC 60079-29-2:07
269
IS 60079(Part 30/Sec
1):2007
Explosive Atmospheres Part 30 Electrical
Resistance Trace Heating Section 1
General And Testing Requirements
(Superseding IS 14774 (Part 1)
IS/IEC 60079-30-1:07
270
IS 60079(Part 30/Sec
2):2007
Explosives Atmospheres Part 30
Electrical Resistance Trace Heating
Section 2 Application Guide for Design ,
Installation And Maintenance
(Superseding IS 14774 (Part 2)
IS/IEC 60079-30-2:07
271
IS 60079(Part 31):2008
Explosives Atmospheres Part 31
Equipment Dust Ignition Protection By
Enclosures"T"
IS/IEC 60079-31:08
272
IS 60127(Part 1):2006
Miniture fuses: Part 1 Definitions for
miniature fuses and general requirements
for miniature fuse links(first revision)
IEC 60127-1(2006)
273
IS 60127(Part 2):2003
Ministure fuses : Part 2 Cartridge fuse links IS/IEC 60127-2:2003
(First Revision)
274
IS 60127(Part 4):2005
Miniature fuses: Part 4 Universal modular
fuse Link (UMF)
IEC 60127-4(2005)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
275
IS 60127(Part 6):1994
Miniature fuses: Part 6 Fuse holders for
miniature cartridge fuse links
IEC 60127-6:1994
276
IS 60309(Part 1):2002
Plugs, socket-outlets and couplers for
industrial purposes: Part 1 General
requirements (first revision)
IEC 60309-1(1999)
277
IS 60309(Part 2):2002
Plugs, socket-outlets and couplers for
industrial purposes: Part 2 Dimensional
interchangeability requirements for pin and
contact-tube accessories
(first revision)
IEC 60309-2(1999)
278
IS 60320(Part 1):2001
Appliance couplers for household and
similar general purposes Part 1 General
requirements
IEC 60320-1(2001)
279
IS 60320(Part 2/Sec
2):1998
Appliance couplers for household and
IEC 60320-2-2(1998)
similar general purposes part 2-2
Interconnection couplers for household and
similar equipment
280
IS 60371(Part 3/Sec
1):2006
Specification for insulating materials based IS/IEC60371-3-1:2006
separators and materials (Superseding IS:
9299(Part 3/Sec 1):1979)
281
IS 60371(Part 3/Sec
2):2005
Specification for insulating materials based IS/IEC60371-3-2:2005
on mica - Part 3: Specification for individual
materials - Sheet 2 : Mica paper
[Superseding IS 9299(Part 3/Sec 7)]
282
IS 60371(Part 3/Sec
3):1983
Specification for insulating materials based IS/IEC60371-3-3:1983
materials for heating equipment
[Superseding IS 9299(Part 3/Sec 4)]
283
IS 60371(Part 3/Sec
4):1992
Specification for insulating materials based IS/IEC60371-3-4:1992
film-backed mica Paper with a B-stage
epoxy Resin binder
284
IS 60371(Part 3/Sec
5):2005
Specification for insulating materials based IS/IEC60371-3-5:2005
backed mica paper with an epoxy resin
binder for post- Impregnation (VPI)
[Supetseding IS 9299(Part 3/Sec 3)& IS
9299 (Part 3/Sec 5)]
285
IS 60371(Part 3/Sec
6):1992
Specification for insulating materials based IS/IEC60371-3-6:1992
backed mica paper With a B-stage epoxy
resin binder (Superseding IS: 9299(Part
3/Sec 6):1993)
286
IS 60371(Part 3/Sec
7):1995
IS/IEC60371-3-7:1995
Sheet 7 : Polyester film mica paper with an
epoxy resin binder for single conductor
taping [Supetseding IS 9299(Part 3/Sec
3)& IS 9299 (Part 3/Sec 5)]
287
IS 60371(Part 3/Sec
8):1995
IS/IEC60371-3-8:1995
Sheet 8 : Mica paper tapes for flameresistant security cables
Sl. No. IS Number/ DOC Number
288
Title
IS 60371(Part 3/Sec
9):1995
ISO/IEC
IS/IEC60371-3-9:1995
Sheet 9 : Moulding micanite [Superseding
IS 9299 (Part 3/ Sec 2)]
289
IS 60470:2000
High Voltage Alternating Current
Contactors and Contactor-Based MotorStarters (superseeding IS 9046:1978 and
IS 12661(Part 1):1988
IS/IEC 60470:2000
290
IS 60517:1990
Gas insulated metal enclosed switchgear
for rated voltages of 72.5 KV and above
IS/IEC 60517:1990
Safety in electro-heat installations:
Part 1General requirements
[Superseding IS 9080 ( Part 1)].
IEC 60519-1:1984
291
* IS 60519(Part 1):1984
292
IS 60519(Part 3):1988
Safety in electroheat installations:
Part 3 Particular requirements for
induction and
conduction heating and
induction melting installations
[Superseding IS 9080 (Part 3 )].
IEC 60519-3:1988
293
IS 60519(Part 5):1980
Safety in electroheat installation :
Part 5 Plasma installations
IEC 60519-5:1980
294
* IS 60519(Part 9):1987
Safety in electroheat installations:
Part 9 Particular requirements for high
frequency dielectric heating installations
IEC 60519-9:1980
295
IS 60529:2001
Classification of Degrees of protection
provided by enclosures (IP Code)
(Superceding IS 12063:1987)
IS/IEC 60529:2001
296
IS 60691:1993
Thermal links - requirements and
application guide
IEC 60691:1993
297
IS 60715:1981
Dimensions of Low-voltage swtichgear and IS/IEC 60715:1981
controlgear - Standardized mounting on
rails of mechanical support of electrical
devices in switchgear and controlgear
installations(Superseding IS 11039)
298
IS 60730(Part 1):1999
Automatic electrical controls for household
and similar use: Part 1 General
requirements
IEC 60730-1 : 1999
299
IS 60898(Part 1):2002
Electrical Accessories - circuit breakers for
over protection for household and similar
installations Part 1 Circuit breakers for a.c.
. operation ( Superseding IS 8828)
IS/IEC 60898-1:2002
300
IS 60898(Part 2):2003
Electrical Accessories - circuit breakers for
over protection for household and similar
installations Part 2 Circuit breakers for a.c.
and d.c. operation
IS/IEC 60898-2:2003
301
IS 60947(Part 1):2007
Low voltage switchgear and controlgear:
Part 1 General Rules (Superseding IS
13947(Part 1) (IEC 60947-1(2007)) (First
Revision)
IS/IEC 60947-1:2007
302
IS 60947(Part 2):2003
Low voltage switchgear and controlgear:
Part 2 Circuit breakers[Superseding IS
13947( Part 2 ):1993]
IS/IEC 60947-2:2003
303
IS 60947(Part 3):1999
Low voltage switchgear and controlgear :
Part 3 Switches, disconnectors, switchdisconnectors and fuse combination units
[Superseding IS 13947(Part 3)]
IS/IEC 60947-3:1999
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
304
IS 60947(Part 4/Sec
1):2000
Low-Voltage switchgear and controlgear:
Part 4 Contactors and motor
starters,Section 1 Electromechanical
contactors and motor starters[superseding
IS 13947(Part 4/Sec 1)
ISIEC 60947-4-1:2000
305
IS 60947(Part 4/Sec
2):1999
Low voltage switchgear and controlgear:
Part 4 Contactors and motors starters
Section 2 ac Semiconductor Motor
Controllers and Starters
ISIEC 60947-4-2:1999
306
IS 60947(Part 4/Sec
3):1999
Low voltage switchgear and controlgear
:Part 4 Contactors and motor starters
Section 3 AC semiconductor controllers
and contactors for non-motor loads
ISIEC 60947-4-3:1999
307
IS 60947(Part 5/Sec
1):2003
Low-voltage switchgear and controlgear: Part 5 Control circuit devices and
switching elements, Section 1
Electromechanical control circuit devices
(Sperseding of IS 13947 Part 5/Sec 1)
ISIEC 60947-5-1:2003
308
IS 61058(Part 1):2001
Switches for Appliances: Part 1 General
Requirement (IEC 61058-1)
IS/IEC 61058-1(2000)
309
IS 61241(Part 0):2004
Electrical apparatus for use in the
presence of combustible dust: Part 0
General requirements (Superseding IS
14154(Part 1) : 1996
IS/IEC 61241-0:2004
310
IS 61241(Part 1):2004
Electrical apparatus for use in the
presence of combustible dust: Part 1:
IS/IEC 61241-1:2004
311
IS 61241(Part 2/Sec
1):2000
Electrical apparatus for use in the
presence of combustible dust: Part 2 Test
methods, Section 1 Method for
determining the minimum ignition
temperatures of dust (Superseding IS
12315-2:1998)
IS/IEC 61241-2-1:94
312
IS 61241(Part 2/Sec
3):1994
Electrical apparatus for use in the
presence of combustible dust: Part 2 Test
methods, Section 3 Method for
determining minimum ignition energy of
dust/air mixtures
IS/IEC 61241-2-3:94
313
IS 61241(Part 4):2001
Electrical apparatus for use in the
IS/IEC 61241-4 :2001
presence of combustible dust: Part 4 Type
314
IS 61241(Part 10):2004
Electrical apparatus for use in the
presence of combustible dust: Part 10 :
Classification of areas where combustible
dusts are or may be present
IS/IEC 61241-10:2004
315
IS 61241(Part 11):2005
Electrical apparatus for use in the
presence of combustible dust: Part 11
ISEC 61241-11:2005
316
IS 61241(Part 14):2004
Electrical apparatus for use in the
presence of combustible dust: Part 14
Selection and installation (Superseding IS
14154(Part 2) : 1997 & IS 13408-1 : 1992)
IS/IEC 61241-14:2004
317
IS 61241(Part 18):2004
Electrical Apparatus for Use in the
Presence of Combustible Dust: Part 18
Protection by Encapsulation
IS/IEC 61241-18:2004
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
318
IS 61308:1994
High frequency dielectric heating
installations -Test methods for the
determination of power output.
319
IS 61400(Part 13):2001
Wind turbines generator systems - Part 13: IS/IEC 61400-13:2001
Measurement of mechanical loads
320
IS 61508(Part 0):2000
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 0:
Functional Safety
(IEC 61508-0:2005)
321
IS 61508(Part 1):1998
Functional safety of
electrical/electronic/progrtammable
elctronic safety - related system - Part 1
General requirement
IEC 61508-1:2000
322
IS 61508(Part 2):2000
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 2
requirement for
electrical/Electronic/programmable
electronic safety - related systems
(IEC 61508-2:2000)
323
IS 61508(Part 3):1998
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 3
software requirements
(IEC 61508-3:1998)
324
IS 61508(Part 4):1998
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 4
Definitions and abbreviations
(IEC 61508-4:1998)
325
IS 61508(Part 5):1998
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 5
Examples of Methods for the
determinations of safety integrity levels
(IEC 61508-5:1998)
326
IS 61508(Part 6):2000
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 6
Guidelines on the applications
(IEC 61508-6:2000)
327
IS 61508(Part 7):2000
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 7
Over view of techniques and measures
IEC 61508-7:2000)
328
IS 61511(Part 1):2003
Functional safety of
electrical/electronic/programmable
electronic safety - related system - Part 1
Framework, definitions,System, hardware
and software requirements
(IEC 61511-1:2003)
329
IS 61511(Part 2):2003
Functional safety - safety instrumented
systems for the process industry sector
Part 2 Guidelines for the Applications
IEC 61511-2:2003
330
IS 61511(Part 3):2003
Functional safety - safety instrumented
systems for the process industry sector Part 3 Guidance for the determination of
the required safety integrity levels
IEC 61511-3:2003
331
IS 61557(Part 1):2007
Electrical safety in low voltage distribution
system up to 1000 V a.c. and 1500 V d.c.
equipment for testing, measuring or
monitorin or protective measurs - Part 1:
Genral requirments IEC 61557-1
(Superseding IS 2992)
IEC 61557-1(2007)
IEC 61308:1994
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
332
IS 61557(Part 2):2007
Electrical safety in low voltage distribance
systems UP to 1 000 V a.c. and 1 500 V
d.c. - Equipment for testing, measuring or
monitoring or protective measures Part 2
Insulation resistance IEC 615572(Superseding IS 11994)
333
IS 61557(Part 5):2007
Electrical safety in low voltage distribution
IEC 61157-5(2007)
systems up to 1000 V a.c. and 1500 V
d.c. - Equipment dor testing, measuring or
monitoring or protective measures - Part 5:
Resistance to earth IEC 61557-5
(Superseding IS 9223)
334
IS 61558(Part 1):1997
Safety of power Transformer,power supply
units and similar: Part 1 General
requirement and test
IS/IEC 61558-1(1997)
335
IS 61558(Part 2/Sec
6):1997
Safety of power Transformers, power
supply units and similar: Part 2 particular
requirements, Section 6 Safety Isolating
transformers for general use
IS/IEC 61558-2-6(97)
336
IS 61558(Part 2/Sec
7):2007
Safety of power Transformers, power
supply units and similar part 2-7:
Particulars requirements for transformers
for toys
IS/IEC 61558-2-7(07)
337
IS 61683:1999
Photovoltaic systems - Power
conditioners - Procedure for measuring
efficiency
IEC 61683:1999
338
IS 61701:1995
Salt mist corrosion testing of photovoltaic
(PV) modules
IEC 61701:1995)
339
IS 61724:1998
Photovoltaic system performance
monitoring - Guidelines for measurment,
data exchange and analysis
IEC 61724:1998
340
IS 61725:1997
Analytical expression for daily solar profiles IS/IEC 61725(1997)
341
IS 61730(Part 2):2004
Photovoltaic (PV) module safety
qualification:
Part 2 Requirments for testing
IEC 61730-2:2004
342
IS 61829:1995
Crystalline silicon photovoltaic (PV) array On site
measurment of I-V characteristics
IEC 61829 : 1995
343
IS 62051(Part 1):2004
Electricity Metering - Data exchange for
IS/IEC 62051-1:2004
meter reading tariff and load control Part 1
Terms relate to data exchange with
metering equipment using DLMS/COSEMV
(IEC 62051-1:2004)
344
IS 62056(Part 21):2002
Electricity Metering Data exchangefor
meter reading, tariff and load control- Part
21 direct local data exchange (IEC 6205621:2002)
IS/IEC 62056-21:2002
345
IS 62056(Part 42):2002
Electricity metering Data exchange for
meter reading tariff and load control -Part
42 Physical layer services and procedures
for connection-oriented asynchronous data
exchange. (IEC 62056-42:2002)
IS/IEC 62056-42:2002
346
IS 62056(Part 46):2007
Electricity metering Data exchange for
meter reading tariff and load control -Part
46 Data link layer using HDLC protocol
(IEC 62056-46:2007)
IS/IEC 62056-46:2007
IEC 61557-2(2007)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
347
IS 62056(Part 47):2006
Electricity Metering - Data Exchange for
meter reading, tariff and load control Part
47 COSEM transport layers for IPv4
networks
IS/IEC 62056-47:2006
348
IS 62056(Part 53):2006
Electricity metering Data exchange for
meter reading tariff and load control -Part
53 COSEM application layer'(IEC 6205653:2006)
IS/IEC 62056-53:2006
349
IS 62056(Part 61):2006
Electricity metering Data exchange for
meter reading tariff and load control -Part
61 Object identification system (OBIS)
(IEC 62056-61:2006)
IS/IEC 62056-61:2006
350
IS 62056(Part 62):2006
Electricity metering Data exchange for
meter reading tariff and load control -Part
62 Interface Classes' (IEC 62056-62:2006)
IS/IEC 62056-62:2006
351
IS 62264(Part 1):2003
Enterprise control system Integration Part
1 Models and Terminology
IEC 62264-1:2003
352
IS 62264(Part 2):2004
Enterprise control system Integration Part
2 Objects Models Attributes
IEC 62264-2:2004
353
IS 62271(Part 1):2007
High-voltage switchgear and controlgear:
Part 1 Common Specification (IEC 622711 :2007) (Superseding IS 12729)
IEC 62271-1 :2007
354
IS 62271(Part 100):2008
High-voltageswitchgear and controlgear:
Part 100 Alternating current Circuit
Breakers(IEC 62271-100 :2008)
IEC 62271-100 :2008
355
IS 62271(Part 102):2003
High-voltage switchgear and controlgear:
Part 102 High-voltage alternating current
circuit breakers
IS/IEC62271-102:2003
356
IS 62271(Part 105):2002
High-voltageswitchgear and controlgear:
Part 105 Alternating current switch-fuse
combinations
IS/IEC62271-105:2002
357
IS 62271(Part 109):2008
High-voltag switchgear and controlgear:
Part 109 Alternating current Series
Capacitor by pass Switches (IEC 62271109 :2008)
IEC 62271-109 : 2008
358
IS 62271(Part 200):2003
High-voltage switchgear and controlgear:
IS/IEC62271-200:2003
Part 200 AC Metal-Enclosed Switchgear
and Controlgear for Rated Voltages Above
1 kV and Up To and Including 52 kV
359
IS 62271(Part 201):2006
High-voltage switchgear and controlgear:
Part 201 AC Insulation Enclosed
Switchgear and Controlgear for Rated
Voltages Above 1 kV and Above 52 kV
IS/IEC62271-201:2006
360
IS 62271(Part 203):2003
High-voltage switchgear and controlgear:
Part 203 Gas-insulated metal-enclosed
switchgear for rated voltages above 52 kV
ISIEC 62271-203:2003
361
ISQC 160000 : 1988
Electrical relays:Part 1 tests and
measurement procedures for
electromechanical all-or-nothing relays
IECQC 60255-7:1978
362
ISQC 160000 : 1988
Electrical relays:Part 2 Applications of the
IEC quality assessment systems for
electronic components to all-or-nothing
relays
IECQC 60255-10:1979
363
ISQC 160100 : 1988
Electrical relays, sectional specification:
Electromechanical all-or-nothing relays of
assessed quality
IECQC 160100:1983
Sl. No. IS Number/ DOC Number
Title
364
Electrical relays, blank detail specification: IECQC 160101:1993
electromechanical all-or-nothing relays of
assessed quality, test schedules 1, 2 and 3
ISQC 160101 : 1988
Total : DUAL NUMBER STANDARDS = 364
ISO/IEC
Sl. No. IS Number/ DOC Number
1
EQUIVALENT STANDARDS
IS 302(Part 1):2008
Title
ISO/IEC
Safety of household and similar electrical
appliances: Part 1 General requirements
(sixth revision)
IEC 60335-1(2006)
2
IS 302(Part 2/Sec
2):1997
Safety of household and similar electrical
appliances:
Part 2 Particular requirements, Section 2
Vacuum cleaners and water suction
cleaning appliances
IEC 60335-2-2(1993)
3
IS 302(Part 2/Sec
3):2007
Safety of household and similar electric
appliances: Part 2 Particular requirements,
Sec 3 Electric iron (first revision)
IEC 60335-2-3(2002)
4
IS 302(Part 2/Sec
4):1993
Safety of household and similar electrical
IEC 60335-2-4(1984)
appliances: Part 2 Particular requirements,
Section 4 Spin extractors
5
IS 302(Part 2/Sec
6):2009
Safety of household and similar electrical
appliances: Part 2 Particuar
requirements, Section 6 Cooking ranges,
cooking tables, ovens and similar
appliances (First Revision)
6
IS 302(Part 2/Sec
7):2009
Safety of household and similar electrical
IEC 60335-2-7(1984)
appliances: Part 2 Particular requirements,
Section 7 Domestic electric clothes
washing machines
7
IS 302(Part 2/Sec
8):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 8 Electric
shavers, hair clippers and similar
appliances
8
IS 302(Part 2/Sec
9):2009
Safety of household and similar electrical
IEC 60335-2-9(1986)
appliances: Part 2 Particular requirements:
Section 9 Electric toasters, grills, roastors
and similar appliances (First Revision)
9
IS 302(Part 2/Sec
11):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 11 Tumbler dryers
10
IS 302(Part 2/Sec
12):1993
Safety of household and similar electrical
IEC60335-2-12(1987)
appliances: Part 2 Particular requirements,
Section 12 Warming plates and similar
appliances
11
IS 302(Part 2/Sec
13):1994
Safety of household and similar electrical
appliances :Part 2 particular requirements,
Section 13 Frying pans, deep fat fryers
and similar appliances
IEC 60335-2-13(1987)
12
IS 302(Part 2/Sec
14):2009
Safety of household and similar electrical
appliances: Part 2 Particular
requirements,Section 14 Electric kitchen
machines (First Revision)
IEC 60335-2-14(1984)
13
IS 302(Part 2/Sec
15):2009
Safety of household and similar electrical
IEC 60335-2-15(1986)
appliances: Part 2 Particular requirements:
Section 15 Appliances for heating liquids
(First Revision)
14
IS 302(Part 2/Sec
21):2011
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 21 Stationary storage type electric
water heater (First Revision
IEC 60335-2-6(1986)
IEC 60335-2-8(1987)
IEC 60335-2-11(1976)
IEC 60335-2-21(1989)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
15
IS 302(Part 2/Sec
23):2009
Safety of household and similar electrical
IEC 60335-2-23(1986)
appliances: Part 2 Particular requirements,
Section 23 Appliances for skin and hair
care (First Revision)
16
IS 302(Part 2/Sec
24):1994
Safety of household and similar electrical
appliances:Part 2 Particular requirements,
Sec 24 Refrigerators, food freezers and
ice makers
IEC 60335-2-24(1992)
17
* IS 302(Part 2/Sec
25):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 25 Microwave ovens
IEC 60335-2-25(1988)
18
IS 302(Part 2/Sec
26):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 26 Clocks
IEC 60335-2-26(1987)
19
IS 302(Part 2/Sec
30):2007
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 30 Room heaters (first revision)
IEC 60335-2-30(2002)
20
IS 302(Part 2/Sec
31):2009
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 31 Range Hoods
IEC 60335-2-31 2002)
21
IS 302(Part 2/Sec
32):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements:
Section 32 Massage appliances
IEC 60335-2-32(1993)
22
IS 302(Part 2/Sec
35):2011
Safety of household and similar electrical
IEC 60335-2-35(1991)
appliances: Part 2 Particular requirements,
Section 35 Electric instantaneous water
heater(First Revision
23
IS 302(Part 2/Sec
45):1994
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Sec 45 Electric heating tools
24
IS 302(Part 2/Sec
46):1993
Safety of household and similar electrical
IEC 60335-2-46(1986)
appliances: Part 2 Particular requirements,
Section 46 Electric steam cookers
25
IS 302(Part 2/Sec
59):1999
Safety of household and similar electrical
appliances : Part 2 Particular requirements
, Section 59 Insect killers
IEC 60335-2-59(1990)
26
IS 302(Part 2/Sec
76):1999
Safety of household and similar electrical
appliances Part 2 Particular requirements,
Section 76 Electric fence energizers
IEC 60335-2-76(1997)
27
* IS 302(Part 2/Sec
80):2003
Safety of household and similar electrical
appliances:
Part 2 Particular requirements, Sec 80
Fans (Superseding IS 12155:1987)
IEC 60335-2-80
28
IS 302(Part 2/Sec
201):2008
Safety of household and similar electrical
appliances: Part 2 Particular requirements,
Section 201 Electric immersion water
heaters
(first revision)
IEC 60335-2-74(2002)
29
IS 325:1996
Three-phase induction motors(first revision) IEC 60034-1(1983)
30
IS 365:1983
Electric hot plates (second revision)
IEC 60302-2-6(1982)
31
* IS 366:1991
Electric irons (fourth revision)
IEC 60311(1988)
32
IS 367:1993
Electric kettles and jugs for household
and similar use (fourth revision)
IEC 60530(1975)
33
* IS 369:1992
Electric radiators (third revision)
IEC 60675
IEC 60335-2-45(1986)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
34
IS 398(Part 1):1996
Aluminium conductors for overhead
transmission purposes: Part 1 Aluminium
stranded conductors (third revision)
IEC 60889:1987
35
IS 398(Part 2):1996
Aluminium conductors for overhead
transmission purposes: Part 2 Aluminium
conductors, galvanized steel reinforced
(third revision)
IEC 889 :1987
36
IS 398(Part 4):1994
Aluminium conductors for overhead
transmission purposes: Part 4 Aluminium
alloy stranded conductors (aluminium
magnesium silicon type) (third revision)
IEC 60208:1966
37
IS 418:2004
Tungsten filament lamps for domestic and
similar general lighting purposes (fourth
revision)
IEC 60064(1993)
38
IS 586:1976
Leclanche type dry batteries for
telecommunications,signalling and general
purposes (third revision)
39
IS 694:1990
PVC Insulated cables for working voltages
upto and including 1100 V (Third revision)
IEC 60227-1to5:1979
40
IS 1175:1981
Methods for grading and classification of
muscovite mica blocks, thins and films
(first revision)
ISO 67
41
IS 1231:1974
Dimensions of three-phase foot-mounted
induction motors (third revision)
IEC 60072 (1971)
42
IS 1248(Part 1):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 1 General requirements
(fourth revision)
IEC 600 51-1(1997)
43
IS 1248(Part 2):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 2 Ammeters and
voltmeters (third revision)
IEC 600 51-2(1984)
44
IS 1248(Part 3):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 3 Wattmeters and
varmeters (third revision)
IEC 600 51-3(1984)
45
IS 1248(Part 4):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 4 Frequency meters
(third revision)
IEC 600 51-4(1984)
46
IS 1248(Part 5):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 5 Phase meters, power
factor meters and synchroscope (third
revision)
IEC 600 51-5(1984)
47
IS 1248(Part 6):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 6 Ohmmeters
(impedance meters) and conductance
meters (third revision)
IEC 600 51-6(1984)
48
IS 1248(Part 7):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 7 Multifunction
instruments (third revision)
IEC 600 51-7(1984)
49
IS 1248(Part 8):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 8 Accessories (third
revision)
IEC 600 51-8(1984)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
50
IS 1248(Part 9):2003
Direct acting indicating analogue electrical
measuring instruments and their
accessories: Part 9 Test methods (third
revision)
IEC 600 51-9(1988)
51
IS 1258:2005
Bayonet lamp holders (fourth revision)
IEC 61184(1997)
52
IS 1287:1993
Electric toasters (third revision)
IEC 60442(1973)
53
IS 1293:2005
Plugs and socket outlets of rated voltage
upto and including 250 volts and rated
current upto and including 16 amperes Specification (third revision)
IEC 60884-1 (2002)
54
IS 1356(Part 1):1972
Electrical equipment of machine tools:
Part 1 Electrical equipment of machines
for general use (second revision)
IEC 60204-1
55
IS 1554(Part 1):1988
PVC insulated (heavy duty) electric cables:
Part 1 For working voltages upto and
including 1 100 V (third revision)
IEC 60502:1983
56
IS 1554(Part 2):1988
PVC insulated (heavy duty) electric
cables:Part 2 For working voltages from
3.3kV upto and including 11 kV (Second
revision)
IEC 60502:1983
57
IS 1569:1976
Capacitors for use in tubular fluorescent
high pressure mercury and low pressure
sodium
vapour discharge lamp circuits ( first
revision)
IEC 566
58
IS 1709:1984
Capacitors for electric fan motors (first
revision)
IEC 252:1975
59
IS 1765:1980
Direct current potentiometers (second
revision)
IEC 60523:1975
60
IS 1766:1998
Time swtiches for metering and load
control
(second revision)
IEC 61038:1992
61
IS 1851:1997
Single Operator type arc welding
transformers (third revision)
ISO 700:1982
62
IS 1866:2000
Code of practice for maintenance and
supervision of mineral insulating oil in
equipment (third revision)
IEC 60296(1982)
Power transformers: Part 1 General (first
revision)
IEC 60076-1(2000)
63
* IS 2026(Part 1):2011
64
IS 2026(Part 2):2010
Power Transformers - Part 2 Temperature
rise (first revision)
IEC 60076-2(1993)
65
IS 2026(Part 4):1977
Power transformers: Part 4 Terminal
marking,tappings and connections (first
revision)
IEC 60076(1977)
66
IS 2026(Part 5):2011
Power Transformers - Part 5 Ability to
withstand short circuit (first revision)
IEC 60076-5(2006)
Stationary storage type electric water
heaters (fourth revision)
IEC 60379(1982)
67
* IS 2082:1993
68
** IS 2165(Part 1):1977
Insulation coordination:
Part 1 Phase to earth insulation
coordination
principles and rules (second revision)
IEC 60071-1:1976
69
** IS 2165(Part 2):1983
Insulation coordination: Part 2 Phase to
phase insulation coordination principles
and rules
IEC 60071-3:1982
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
70
IS 2215:2006
Starters for fluorescent lamps (third
revision)
71
IS 2223:1983
Dimensions of flange mounted ac induction IEC 60072 (1971)
motors (first revision)
72
IS 2253:1974
Designation for types of construction and
IEC 34-7(1972)
mounting arrangement of rotating electrical
machines (first revision)
73
IS 2259:1963
Methods of test for determination of
insulation resistance of solid insulating
materials
IEC 60167(1964)
74
* IS 2312:1967
Propeller type ac ventilating fans (first
revision)
IEC 60665(1981)
IEC 81(1974)
IEC 60155 (1993)
75
IS 2418(Part 1):1977
Tubular fluorescent lamps for general
lighting service: Part 1 Requirements and
tests (first revision)
76
IS 2418(Part 2):1977
Tubular fluorescent lamps for general
IEC 81(1974)
lighting service : Part 2 Standard lamp data
sheets (first revision)
77
IS 2418(Part 3):1977
Tubular fluorescent lamps for general
lighting service : Part 3 Dimensions of G5and G-13 bi-pin caps (first revision)
IEC 61-1(1969)
78
IS 2418(Part 4):1977
Tubular fluorescent lamps for general
lighting service: Part 4 Go and no-go
gauges for G-5 and
G-13 bi-pin caps (first revision)
IEC 61-3(1969)
79
IS 2419:2012
80
IS 2486(Part 2):1989
Insulator fittings for overhead power lines
IEC 120 (1984)
with nominal voltage greater than1000 V Specification :
Part 2 Dimensional requirements (second
revision)
81
IS 2486(Part 3):1974
Specification for Insulator fittings for
overhead power lines with a nominal
voltage greter than 1 000 Volts: Part 3
Locking devices
IEC 372-1 (1971)
82
IS 2486(Part 4):1981
Specification for Insulator fittings for
overhead power lines with a nominal
voltage greater than1 000 V: Part 4 Test
for locking devices
IEC 372-2 (1976)
83
IS 2511:1963
Specification for Polycrystalline
semiconductor rectifier stacks
IEC 60119(1960)
84
IS 2544:1973
Porcelain post insulators for systems with
nominal voltage greater than 1000 Volts
(first revision)
IEC 168 (1964)
85
IS 2705(Part 1):1992
Current transformers: Part 1 General
requirements (second revision)
IEC 60185(1966)
86
IS 2705(Part 2):1992
Current transformers: Part 2 Measuring
current transformers (second revision)
IEC 60185(1966)
87
IS 2705(Part 3):1992
Current transformers: Part 3 Protective
current transformers (second revision)
IEC 60185(1966)
88
IS 2705(Part 4):1992
Current transformers: Part 4 Protective
current transformers for special purpose
applications (second revision)
IEC 60185(1966)
IEC 61554 : 1999
Panel Mounting ( Second Revision )
Sl. No. IS Number/ DOC Number
Title
89
Thermostats for use with electric water
heaters (first revision)
IEC 60730(1982)
Lightning arresters for alternating current
systems :
Part 3 Metal oxide surge-arresters without
gaps
for ac systems
IEC 60099-4:1991
90
IS 3017:1985
* IS 3070(Part 3):1993
ISO/IEC
91
IS 3136:1965
Specification for Polycrystalline
semiconductor rectifier equipment
IEC 60119(1960)
92
IS 3151:1982
Earthing transformers (first revision)
IEC 60289(1968)
93
IS 3156(Part 1):1992
Voltage transformers: Part 1 General
requirements (second revision)
IEC 60186(1987)
94
IS 3156(Part 2):1992
Voltage transformers: Part 2 Measuring
voltage transformers (second revision)
IEC 60186(1987)
95
IS 3156(Part 3):1992
Voltage transformers: Part 3 Protective
voltage transformers (second revision)
IEC 60186(1987)
96
IS 3156(Part 4):1992
Voltage transformers: Part 4 Capacitor
voltage transformers (second revision)
IEC 60186(1987)
97
IS 3231(Part 1/Sec
3):1986
Electrical relays for power system
protection: Part 1 General requirements,
Section 3 High frequency disturbance test
for static relays (first revision)
IEC 255-4 (1976)
98
IS 3231(Part 2/Sec
1):1987
Electrical relays for power system
protection: Part 2 Requirements for
principal families, Section 1 All or nothing
relays
IEC 255-1-00
99
IS 3231(Part 2/Sec
3):1987
Electrical relays for power system
protection: Part 2 Requirements for
principal families, Section 3 General
requirements for thermal relays
IEC 255-8 (1978)
100
IS 3231(Part 3/Sec
1):1987
Electrical relays for power system
protection: Part 3 Requirements for
particular group of relays, Section 1 Nonspecified time or independent specified
time measuring relays
IEC 255-3 (1971)
101
IS 3231(Part 3/Sec
2):1987
Electrical relays for power system
IEC 255-4 (1976)
protection: Part 3 Requirements for
particular group of relays, Section 2
Dependent specified time measuring relays
102
IS 3231(Part 3/Sec
3):1987
Electrical relays for power system
IEC 255-13(1980)
protection:Part 3 Requirements for
particular group of relays, Section 3 Biased
(percentage) differential relays
103
IS 3231(Part 3/Sec
4):1987
Electrical relays for power system
protection: Part 3 Requirements for
particular group of relays, Section 4
Directional relays and power relays
IEC 255-12 (1980)
104
IS 3231(Part 3/Sec
5):1987
Electrical relays for power system
Protection: Part 3 Requirements for
particular group of relays, Section 5
Impedance measuring relays
IEC255-16 (1982)
105
IS 3323:1980
Bi-pin lampholders for tubular fluorescent
lamps
(first revision)
IEC 60400(1972)
106
IS 3324:1982
Holders for starters for tubular fluorescent
lamps
(first revision)
IEC 400(1972)
Sl. No. IS Number/ DOC Number
Title
107
Application guide for insulation
coordination (first revision)
IEC 60071-2:1976
* IS 3716:1978
ISO/IEC
108
IS 3722(Part 1):1983
Letter symbols and signs used in electrical
technology: Part 1 General guidance on
symbols and subscripts
(first revision)
IEC 60027-1(1992)
109
IS 3722(Part 2):1983
Letter symbols and signs used in electrical
technology: Part 2 Reference tables for
symbols and subscripts
(first revision)
IEC 60027-1(92)
Switches for domestic and similar
purposes (second revision)
IEC 60669-1(1998)
IEC 60146(1963)
110
* IS 3854:1997
111
IS 3895:1966
Specification for Monocrystalline
semiconductor rectifier cells and stacks
112
IS 4029:2010
Guide for testing three-phase induction
motors (First Revision)
113
IS 4159:2002
Mineral filled sheathed heating elements
(third revision)
IEC 60335-2-73(1994)
114
IS 4160:2005
Interlocking switch socket outlets Speification
(first revision)
IEC 60884-2-6 (1997)
115
IS 4165:1991
Thermostats for general purpose electric
ovens
(first revision)
IEC 60730(1982)
116
IS 4289(Part 1):1984
Flexible cables for lifts and other flexible
connections: Part 1 Elastomer insulated
cables (first revision)
IEC 60245-5
117
IS 4289(Part 2):2000
Flexible cables for lifts and other flexible IEC 60227-6:1985
Connections:Part 2 PVC insulated cables
118
IS 4540:1968
Specification for Monocrystalline
semiconductor
rectifier assemblies and equipment
IEC 60146(1963)
119
IS 4559:1993
Single operator rectifier type dc arc
welding power source (second revision)
ISO 700:1982
120
IS 4889:1968
Method of determination of efficiency of
rotating electrical machines
IEC 2 D
121
IS 5350(Part 1):1970
Dimensions of indoor and outdoor
porcelain post insulator and post insulator
units for system with nominal voltage
greater than 1000 V: Part 1 Indoor post
insulators
IEC 273 (1968)
122
IS 5350(Part 3):1971
Dimensions of indoor and outdoor
porcelain post insulators and post insulator
units for system with nominal voltages
greater than 1000 V: Part 3 Outdoor
pedestal post insulators
IEC 273 (1968)
123
Turbine type generators (first revision)
IEC 60034-3(1988)
124
* IS 5422:1996
IS 5553(Part 1):1989
Reactors: Part 1 General
IEC 60289(1988)
125
IS 5553(Part 2):1990
Reactors: Part 2 Shunt reactors
IEC 60 289(1988)
126
IS 5553(Part 3):1990
Reactors: Part 3 Current limiting reactors
and neutral earthing reactors
IEC 60289(1988)
127
IS 5553(Part 4):1990
Reactors: Part 4 Damping reactors
IEC 60289(1988)
128
IS 5553(Part 5):1989
Reactors: Part 5 Tuning reactors
IEC 60289(1988)
129
IS 5553(Part 6):1991
Reactors: Part 6 Earthing transformers
(Neutral couplers)
IEC 60289(1988)
Sl. No. IS Number/ DOC Number
Title
130
IS 5553(Part 7):1990
Reactors: Part 7 Arc supression reactors
IEC 60289(1988)
131
IS 5553(Part 8):1990
Reactors: Part 8 Smoothing reactors
IEC 60289(1988)
132
IS 5571:2009
Guide for selection and installation of
electrical equipment in hazardous areas
(other than mines
(third revision)
IEC 60079-14(2002)
133
IS 5572:2009
Classification of hazardous areas (other
than mines) having flammable gases and
vapours for electrical installation (third
revision of IS 5572)
IEC 60079-10(2002)
134
IS 5578:1984
Guide for marking of insulated conductors
(first revision)
IEC 60391(1972)
135
IS 5790:1985
Domestic electric cooking ovens (first
revision)
IEC 60350
136
IS 5831:1984
PVC insulation and sheath of electric
cables (first revision)
IEC 60502:1983
137
IS 6008:1989
Single operator ac/dc arc welding
power source (first revision)
IEC 700:1982
138
IS 6162(Part 1):1971
Paper covered aluminium conductors :
Part 1 Round conductors
IEC 60111
139
IS 6162(Part 2):1971
Paper covered aluminium conductors:Part
2 Rectangular conductors
IEC 60111
140
IS 6236:1971
Direct recording electrical measuring
instruments
IEC 60258(1968)
141
IS 6290:1986
Steam irons (first revision)
IEC 60311(1970)
142
* IS 6303:1984
General requirements and methods of
tests for dry cells and batteries
IEC 86-1(1972)
143
IS 6303(Part 4):2013
ISO/IEC
IEC 60086-4:2007
batteries
144
IS 6380:1984
Elastomeric insulation and sheath of
electric cables (first revison)
IEC 60502:1983
145
IS 6616:1982
Ballasts for high pressure mercury vapour
lamps
(first revision)
IEC 262(1969)
146
IS 6680:1992
Railway carriage fans (first revision)
IEC 60342-1
147
IS 6701:1985
Tungsten filament miscellaneous electric
lamps
(first revision)
IEC 61-1(1969)
148
* IS 6792:1992
Method for determination of electric
strength of insulating oils (first revision)
IEC 60156(1963)
149
IS 6848:1979
Lead-acid batteries for train lighting and
airconditioning services (first revision)
IEC 77(1968)
150
IS 7027:1984
Transistorized ballasts for fluorescent
lamps
(first revision)
IEC 458 (1982)
151
IS 7098(Part 1):1988
Cross-linked polyethylene insulated
thermosplastic sheathed cables Specification : Part 1 For working voltages
upto and including 1 100 V (first revision)
IEC 60502:1983
152
IS 7098(Part 2):2011
Crosslinked polyethylene insulated
thermoplastic sheathed cables Specification : Part 2 For working voltages
from 3.3 kV upto and including 33 kV
(second revision)
IEC 60502-2:2005
153
IS 7132:1973
Guide for testing synchronous machines
IEC 60034-1(1969)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
154
IS 7204(Part 2):1980
Specification for Stabilized power supplies
dc output:
Part 2 Rating and performance .
IEC 60478-2(1975)
155
IS 7204(Part 3):1980
Specification for Stabilized power
supplies dc output: Part 3 Radio
frequency interference tests
IEC 60478-3(1976)
156
IS 7204(Part 4):1980
Specification for Stabilized power
supplies dc output: Part 4 Tests other
than radio-frequency interference.
IEC 60478-4(1976)
157
* IS 7306:1974
Methods for determining synchronous
machine quantities from tests
IEC 60034-4(1967)
158
IS 7372:1995
Lead-acid storage batteries for motor
vehicles (first revision)
IEC 95-1(1988)
159
IS 7391(Part 1):1974
Cotton covered copper conductors : Part 1
Round conductors
IEC 60182
160
IS 7576:1974
Bunched enamelled copper conductors
with silk covering
IEC 60317-1
161
IS 7624:1990
Lead-acid starter batteries for diesel
locomotives and rail cars (first revision)
IEC 95-1(1980)
162
* IS 7691:1975
Frequencies for special power applications
IEC 60113-1(71)
163
IS 7788:1975
Specification for Single-phase traction
power converters
IEC 60411(1973)
164
IS 7809(Part 1):1975
Pressure sensitive adhesive tapes for
electrical purposes: Part 1 General
requirements
IEC 60454-1(1974)
165
IS 7809(Part 2):1977
Pressure sensitive adhesive tapes for
electrical purposes: Part 2 Methods of test
IEC 60454-2(1974)
166
IS 7809(Part 3/Sec
1):1986
Pressure sensitive adhesive tapes for
electrical purposes: Part 3 Requirements
for individual materials, Section 1
Plasticized polyvinylchloride tapes with
non-thermosetting adhesive (first revision)
IEC 60454-2
167
IS 7914:1975
Standard cells
IEC 60428(1973)
168
IS 8030:1976
Luminaires for hospitals
IEC 162(1972)
169
* IS 8130:2013
Conductors for insulated electric cables
and flexible cords (second revision)
IEC 60228:1978
170
* IS 8144:1997
Multipurpose dry batteries (First revision)
IEC 86-2(1972)
171
IS 8187:1976
D-type fuses
IEC 269-3(1973)
172
IS 8223:1999
Dimensions and output series for rotating
electrical machines (first revision)
IEC 60072-2(1990)
173
IS 8270(Part 1):1976
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 1
Definitions and classification
IEC 60113-1(71)
174
IS 8270(Part 2):1976
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 2
Item designation
IEC 60113-2(71)
175
IS 8270(Part 3):1977
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 3
General requirements for diagrams
IEC 60113-2(71)
176
IS 8270(Part 4):1977
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 4
Circuit diagrams
IEC 60113-2(71)
177
IS 8270(Part 5):1976
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 5
Interconnection diagrams and tables
IEC 60113-2(71)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
178
IS 8270(Part 6):1983
Guide for preparation of diagrams, charts
and tables for electrotechnology: Part 6
Unit wiring diagrams and tables
179
IS 8504(Part 1):2012
Electrical insulating materials properties of
thermal endurance Part 1: Ageing
procedures and evaluation of test results
(Second Revision)
180
IS 8504(Part 2):2013
Electrical insulating materials - Thermal
endurance properties - Part 2:
Determination of thermal endurance
properties of electrical insulating
materials - Choice of test criteria (First
Revision)
IEC 60216-2(2005)
181
IS 8504(Part 3):1994
Guide for determination of thermal
endurance properties of electrical
insulating materials Part 3 : Statistical
methods
IEC 60216-3
182
IS 8504(Part 4):2013
Electrical insulating materials - Thermal
endurance properties - Part 4: Instructions
for calculating thermal endurance
characteristics (First Revision)
IEC 60216-3(2006)
183
IS 8504(Part 5/Sec
1):2012
Electrical insulating materials - Thermal
endurance properties - Part 5 Ageing
ovens Sec 1 Single-chamber ovens
IEC 60216-4-1(2006)
184
IS 8504(Part 5/Sec
2):2012
Electrical insulating materials - Thermal
endurance properties - Part 5: Ageing
ovens Sec 2 Precision ovens for use up to
300 °C
IEC 60216-4-2(2000)
185
IS 8504(Part 5/Sec
3):2012
Electrical insulating materials - Thermal
endurance properties - Part 5 Ageing
ovens Sec 3 Multi-chamber ovens
IEC 60216-4-3(2000)
186
IS 8504(Part 6):2012
Electrical insulating materials - Thermal
endurance properties - Part 6:
Determination of relative thermal
endurance index (RTE) of an insulating
material
IEC 60216-5(2008)
187
IS 8504(Part 7):2012
Electrical insulating materials - Thermal
IEC 60216-6(2006)
endurance properties - Part 7 :
Determination of thermal endurance
indices (TI and RTE) of an insulating
material using the fixed time frame method
188
IS 8530:1977
Maximum demand indicators (class 1)
IEC 60211:1966
189
IS 8685:1977
Aircraft lamps
IEC 60434 (1973)
190
IS 8686:1977
Static protective relays
IEC 255-4
191
IS 8704:1995
Artificial pollution on high voltage insulators IEC 507 (1991)
to be used on ac systems (first revision)
192
IS 8804:1993
Plugs, sockets and terminal arrangements
and welding cable connectors for manual
welding equipment (first revision)
IEC 501:1975
193
IS 8913:1978
Methods of measurement of lamp cap
temperature rise
IEC 360(1971)
194
IS 8992:1978
Test methods for induction furnaces
with submerged channels
IEC 60396(1972)
195
IS 9021:1978
General test conditions for industrial
electro-heating equipment
IEC 60398(1972)
196
IS 9029:1978
Methods of tests for batch furnaces with
metallic heating resistors
IEC 60397(1972)
IEC 60113-2(71)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
197
IS 9043:1979
Method for grading (by size) of phlogopite
mica blocks, thins and splittings
ISO 444(1965)
198
IS 9044:1979
Method of measuring thickness of mica
blocks, thins, films and splittings
ISO 5972(1978)
199
IS 9045:1979
Thermal classification of phlogopite mica
splittings
ISO 5023(1977)
200
** IS 9050:1979
Nominal dimensions of cylindrical
IEC 60239(1967)
machines
graphite electrodes with threaded sockets
and connecting pins for use in electric
arc furnaces.
201
** IS 9080(Part 2/Sec
1):1979
Safety requirements in electro-heat
installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 1 Protection in direct
resistance heating installations
IEC 60519-2(1975)
202
** IS 9080(Part 2/Sec
3):1981
Safety requirements in electro-heat
installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 3 Protection in potassium and
sodium nitrate and nitrite bath furnaces
IEC 60519-2(1975)
203
** IS 9080(Part 2/Sec
4):1981
Safety requirements in electro-heat
IEC 60519-2(1975)
installations:
Part 2 Particular requirements for
resistance heating equipment,
Section 4 Protection in installations used
for
drying varnishes and other similar products
204
** IS 9080(Part 4):1981
Safety requirements in electro-heat
installations:
Part 4 Particular requirements for arc
furnace installations.
IEC 60519-4(1977)
205
IS 9206:1979
Dimensions of caps for tungsten filament
general service electric lamps
IEC 60061-1(1969)
206
IS 9249(Part 1):1979
Safety requirements for indicating and
recording electrical measuring instruments
and their accessories: Part 1 Common
safety requirements for instruments
IEC 60414(1973)
207
IS 9249(Part 2):1982
Safety requirements for indicating and
recording electrical measuring instruments
and their accessories: Part 2 Safety
requirements for instruments using a
mains supply
IEC 60414((1973)
208
IS 9251:1979
Capacitors for inductive heat generating
IEC 60110:1973
plants operating at frequencies between 40
and 24 000 Hz
209
IS 9335(Part 1):1979
Cellulosic papers for electrical purposes:
IEC 60554-1(1977)
Part 1 Definitions and general requirements
210
IS 9335(Part 3/Sec
1):1984
Cellulosic papers for electrical purposes:
Part 3 Specifications for individual
materials, Section 1 General purposes
electrical paper
IEC 60554-3-1
211
IS 9335(Part 3/Sec
2):1985
Cellulosic papers for electrical purposes:
Part 3 Specifications for individual
materials, Section 2 Capacitor paper
IEC 60554-3-2
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
212
IS 9335(Part 3/Sec
3):1984
Cellulosic papers for electrical purposes:
Part 3 Specifications for individual
materials, Section 3 Crepe paper
IEC 60554-3-3(1980)
213
IS 9335(Part 3/Sec
4):1984
Cellulosic papers for electrical purposes:
Part 3 Specifications for individual
materials, Section 4 Electrolytic capacitor
paper
IEC 60554-3-4(1979)
214
IS 9335(Part 3/Sec
5):1985
Cellulosic papers for electrical purposes:
Part 3 Specifications for individual
materials, Section 5 Special papers
IEC 60554-3-5
215
IS 9385(Part 1):1979
High voltage fuses:Part 1 Current limiting
fuses
IEC 282-1(1979)
216
IS 9385(Part 2):1980
High voltage fuses:Part 2 Expulsion and
similar fuses (superseding IS:5792)
IEC 282-2(1970)
217
IS 9385(Part 3):1980
High voltage fuses:Part 3 Application guide IEC 282-2(1970)
for high voltage fuses
218
IS 9385(Part 5):1983
High voltage fuses:Part 5 Types and
dimensions of
fuse-links for current limiting fuses
IEC 282-1A(1978)
219
IS 9402:1980
High voltage fuses for the external
protection of shunt power capacitors
IEC 549(1976)
220
IS 9409:1980
Classification of electrical and electronic
IEC 61140 (2001)
equipment with regard to protection against
electric shock
221
* IS 9434:1992
222
223
Guide for sampling and analysis of free
and dissolved gases and oil from oil-filled
electrical equipment (first revision)
IEC 60567(1977)
IS 9499:1980
Conventions concerning electric and
magnetic circuits
IEC 60375(72)2003
IS 9502:1980
Muscovite mica components for electronic
equipment
ISO 5816-1(1979)
224
* IS 9537(Part 1):1980
Conduits for electrical installations: Part 1
General requirements
IEC 60614-1(1978)
225
** IS 9537(Part 3):1983
Conduits for electrical installations: Part 3
Rigid plain conduits of insulating materials
(superseding IS:2509)
IEC 60614-2-2(1980)
226
* IS 9537(Part 5):2000
Conduits for a electrical installations: Part
5 Pliable conduits of insulating material
(Superseding IS 6946)
IEC 60614-2-3(1990)
227
IS 9537(Part 6):2000
Conduit for electrical installations: Part 6
Pliable conduits of metal or composit
materials
IEC 60614-2-6(1992)
228
IS 9583:1981
Emergency lighting units
IEC 598-2-22(1980)
229
IS 9857:1990
Welding cables (first revision)
IEC 60245-6
230
IS 9900(Part 1):1981
High pressure mercury vapour lamps:
Part 1 Requirements and test
(Superseding IS:2183 and IS:7023)
IEC 188(1974)
231
IS 9900(Part 2):1981
High pressure mercury vapour lamps: Part
2 Standard lamp data sheets (superseding
IS: 2183 and IS: 7023)
IEC 188(1974)
232
IS 9900(Part 3):1981
High pressure mercury vapour lamps :
Part 3 Dimensions of lamp caps
(superseding IS:2183 and IS:7023)
IEC 188(1974)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
233
IS 9900(Part 4):1981
High pressure mercury vapour lamps :
Part 4 Go and no-go gauges of lamp caps
(superseding IS:2183 and IS:7023)
IEC 61-3(1969)
234
* IS 9920(Part 3):1982
Switches and switch isolators for voltages
above 1000 V: Part 3 Design and
construction
IEC 60129:1975
235
* IS 9920(Part 4):1985
Switches and switch isolators for voltages
above 1000 V: Part 4 Type tests and
routine tests
IEC 60129:1975
236
* IS 9921(Part 1):1981
Alternating current disconnectors
IEC 60129:1975
(isolators) and earthing switches for
voltages above 1000 V: Part 1 General and
definitions
237
* IS 9921(Part 2):1982
Alternating current disconnectors
(isolators) and earthing switches for
voltages above 1000 V: Part 2 Rating
238
* IS 9921(Part 3):1982
Alternating current disconnectors
IEC 60129:1975
(isolators and earthing switches for
voltages above 1 000 V: Part 3 Design and
construction
239
* IS 9921(Part 4):1985
Alternating current disconnectors
(isolators) and earthing switches for
voltages above 1000 V: Part 4 Type tests
and routine tests
IEC 60129:1975
240
* IS 9921(Part 5):1985
Alternating current disconnectors
(isolators) and earthing switches for
voltages above 1 000 V: Part 5
Information to be given with tenders,
inquiries and orders
IEC 60129:1975
241
IS 9974(Part 1):1981
High pressure sodium vapour lamps :
Part 1 General requirements and tests
IEC 662(1980)
242
IS 9974(Part 2):1981
High pressure sodium vapour lamps :
Part 2 Standard lamp data sheets
IEC 662(1980)
243
* IS 10026(Part 1):1998
Insulating varnishes containing solvents:
Part 1 Definitions and general
requirements (first revision)
IEC 60464-1(1976)
244
* IS 10026(Part 2):1999
Insulating varnishes containing solvents:
Part 2 Methods of tests(first revision)
IEC 60464-2(19860
245
* IS 10026(Part 3/Sec
1):1999
Insulating varnishes containing solvents:
Part 3 Specifications for individual
materials, Section1Requirements for cold
curing varnishes
(first revision)
IEC 60464-3-1(1986)
246
* IS 10026(Part 3/Sec
2):1999
Insulating varnishes containing solvents:
Part 3 Specifications for individual
materials, Section 2 Requirements for hot
curing varnishes
(first revision)
IEC 60464-3-2(1989)
IEC 60129:1975
247
IS 10031:1981
Taper barrelled delivery spools for covered
round electrical winding wires
IEC 60264-3(1973)
248
IS 10098:1982
General requirements for electric
infra-red emitters for heating purposes.
IEC 60240(1967)
249
** IS 10122:1982
Methods of tests for crucible induction
furnaces
IEC 60545(1979)
Sl. No. IS Number/ DOC Number
Title
250
Recommended methods of tests for the
determination of dielectric properties of
insulating materials at frequencies above
300 MHz: Part 1 General
IS 10163(Part 1):1982
ISO/IEC
IEC 60377-1(1973)
251
* IS 10189(Part 2/Sec
1):1993
Industrial process control valves: Part 2
IEC 60534-2-1(1978)
Flow capacity, Section 1 Sizing equations
for incompressible fluid flow under installed
conditions
252
** IS 10189(Part 2/Sec
2):1993
Industrial process control valves: Part 2
Flow capacity SectIon 2 Sizing equations
for compressible fluid flow under installed
conditions
IEC60534-2-2(1980)
253
** IS 10215:1982
Methods of tests for submerged arc
furnaces
IEC 60683(1980)
Electrical installations in ships: Part 1
General, Section 1 Definitions and general
requirements (first revision)
IEC 60092-101:1980
254
IS 10242(Part 1/Sec
1):1997
255
* IS 10242(Part 2/Sec
1):1982
Electrical installations in ships: Part 2
System design, Section 1 General
IEC 60092-201:1980
256
IS 10242(Part 2/Sec
2):1983
Electrical installations in ships: Part 2
System design, Section 2 Protection
IEC 60092-202:1980
257
IS 10242(Part 2/Sec
4):1993
Electrical installationss in ships: Part 2
System design, Sec 4 Electric and
electrohydraulic steering gear
IEC 60092-204:1987
258
IS 10242(Part 3/Sec
1):1983
Electrical installations in ships: Part 3
Equipment, Section 1 Generators and
motors
IEC 60092-301:1980
259
IS 10242(Part 3/Sec
2):1984
Electrical installations in ships: Part 3
Equipment, Section 2 Switchgear and
controlgear assemblies
IEC 60092-302:1980
260
IS 10242(Part 3/Sec
3):1984
Electrical installations in ships: Part 3
Equipment, Section 3 Transformers for
power and lighting
IEC 60092-303:1980
261
IS 10242(Part 3/Sec
4):1987
Electrical installations in ships: Part 3
Equipment, Section 4 Semi-conductor
convertors
IEC 60092-304:1980
262
IS 10242(Part 3/Sec
5):1990
Electrical installations inn ships: Part 3
Equipment, Section 5 Accumulators
(storage) batteries
IEC 60092-305:1980
263
IS 10242(Part 3/Sec
6):1986
Electrical installations in ships: Part 3
Equipment, Section 6 Luminaires and
accessories
IEC 60092-306:1980
264
IS 10242(Part 3/Sec
7):1990
Electrical installations in ships:Part 3
Equipment, Section 7 Heating and cooking
appliances
IEC 60092-307:1980
265
IS 10242(Part 3/Sec
10):1992
Electrical installations in ships: Part 3
Equipment, Section 10 General
construction and test requirements for low
voltage shipboard power cables
IEC 60092-350
266
IS 10242(Part 3/Sec
11):1986
Electrical installations in ships: Part 3
Equipment, Section 11 Insulating materials
for shipboard power cables
IEC 60092-35:1983
267
IS 10242(Part 3/Sec
12):1986
Electrical installations in ships: Part 3
Equipment, Section 12 Choice and
installation of cables for low voltage
systems
IEC 60092-352:1979
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
268
IS 10242(Part 3/Sec
13):1992
Electrical installations in ships: Part 3
Equipment, Section 13 Single and
multicore cables with extruded solid
insulation for rated voltage 0.6/1 kV
269
IS 10242(Part 3/Sec
19):1990
Electrical installations in ships: Part 3
IEC 60092-359:1987
Equipment, Section 19 Sheathing materials
for telecommunication and power
shipboard cables
270
IS 10242(Part 3/Sec
23):1987
Electrical installations in ships: Part 3
Equipment, Section 23 Shipboard
telecommunication cables and radio
frequency cables: Shipboard flexible
coaxial cables
IEC 60092-373:1977
271
IS 10242(Part 3/Sec
24):1987
Electrical installations in ships: Part 3
Equipment, Section 24 Shipboard
telecommunication cables and
radiofrequency cables: Telephone cables
for non-essential communication services
IEC 60092-374:1977
272
IS 10242(Part 3/Sec
25):1987
Electrical installations in ships: Part 3
IEC 60092-375:1977
Equipment, Section 25 Shipboard
telecommunication cables and radio
frequency cables: General instrumentation,
control and communication cables
273
IS 10242(Part 3/Sec
26):1987
Electrical installations in ships: Part 3
Equipment, Section 26 Shipboard
telecommunication cables: Shipboard
multicore cables for control circuits
IEC 60092-376:1983
274
IS 10242(Part 4):1992
Electrical installations in ships: Part 4
Installation and test of completed
installation
IEC 60092-401:1980
275
IS 10242(Part 5/Sec
1):1993
Electrical installations in ships: Part 5
Special features, Sec 1 Electric propulsion
plant
IEC 60092-501:1984
276
* IS 10242(Part 5/Sec
2):1997
Electrical installations in ships: Part 5
Special features, Section 2 Tankers
IEC 60092-502:1999
277
IS 10242(Part 5/Sec
3):1993
Electrical installations in ships: Part 5
Special features Sec 3 ac supply system
with voltage in the range above 1 kV up to
and including 11 kV
IEC 60092-503:1975
278
IS 10242(Part 5/Sec
4):1998
Electrical installations in ships : Part 5
Special features, Section 4 Control and
instruments
IEC 60092-504:2001
279
IS 10276(Part 1):1982
Edison screw lampholders :
Part 1 Requirements and tests
IEC 60238(1975)
280
IS 10276(Part 2):1982
Edison screw lampholders :
Part 2 Standard data sheets for lamp
holders and gauges
IEC 60238(1975)
281
IS 10322(Part 1):2014
Luminaires: Part 1 General requirements
and tests [first revision of IS 10322 (Part 1
to Part 4)]
IEC 60598-1(2003-10)
282
IS 10322(Part 2):1982
Luminaires: Part 2 Constructional
requirements
IEC 598-1(1979)
283
IS 10322(Part 4):1984
Luminaires: Part 4 Methods of tests
IEC 598-1(1979)
284
IS 10322(Part 5/Sec
1):2012
Luminaires: Part 5 Particular
requirements, Sec 1 Fixed general
purpose luminaires (First revision)
IEC 60598-2-1(1979)
IEC 60092-353:1988
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
285
IS 10322(Part 5/Sec
2):2012
Luminaires: Part 5 Particular
IEC 60598-2-2 (1979)
requirements,
Sec 2 Recessed luminaires (First revision)
286
IS 10322(Part 5/Sec
3):2012
Luminaires: Part 5 Particular
requirements,
Sec 3 Luminaires for road and street
lighting
(First revision)
287
IS 10322(Part 5/Sec
5):2013
Luminaires: Part 5 Particular requirements, IEC 60598-2-5
Section 5 Flood lighting (First revision)
288
IS 10436:1983
Electric frying pans and deep fat fryers
289
IS 10462(Part 1):1983
Fictitious calculation method for
IEC 60502:1978
determination of dimensions of protective
coverings of cables:Part 1 Elastomeric and
thermoplastic insulated cables
290
IS 10462(Part 2):1991
Fictitious calculation method for
IEC 60055-2
determination of dimensions of protective
coverings of cables: Part 2 Paper insulated
cables
291
IS 10561:1983
Application guide for power transformers
IEC 606 (1978)
292
IS 10581:1983
Methods of test for determination of ionic
impurities in electrical insulating materials
by extraction with liquids
IEC 60589(1977)
293
IS 10624:1983
High voltage fuse-links for motor circuit
applications
IEC 644(1979)
294
IS 10659:1983
Specification for Direct current bridges for
measuring resistance (superseding
IS:1565)
IEC 60564(1977)
295
IS 10918:1984
Vented type nickel cadmium batteries
IEC 623(1978)
296
* IS 11064:1984
Guide for construction and use of rooms
or buildings protected by pressurization for
installation of electrical apparatus for
explosive gas atmospheres
IEC 60079-13(1982)
297
IS 11171:1985
Dry type power transformers
IEC 60726(1982)
298
IS 11182(Part 1):1984
Guide for evaluation of insulation systems
of electrical equipment: Part 1
Identification, evaluation and ageing
mechanisms
IEC 60505(1975)
299
IS 11182(Part 2):1984
Guide for evaluation of insulation systems
of electrical equipment: Part 2 Thermal
endurance test procedure
IEC 60611(1978)
300
IS 11182(Part 3/Sec
1):1986
Guide for evaluation of insulation systems
of electrical equipment: Part 3 Electrical
endurance test procedures, Section 1
General considerations and evaluation
procedures based on normal distributions
IEC 60727-1(1982)
301
IS 11182(Part 3/Sec
2):1996
Guide for evaluation of insulation systems
of electrical equipments: Part 3 Electrical
endurance test procedures Section 2
evaluation procedure based on extreme
value distribution
IEC 60727-2(1993)
302
IS 11221:1984
Recommended test methods for
determining the relative resistance of
insulating materials to breakdown by
surface discharges
IEC 60343(1970)
IEC 60598-2-3 (1979)
IEC 60335-2-13
Sl. No. IS Number/ DOC Number
Title
303
IS 11256(Part 1):1985
Method of test for determination of thermal
endurance of insulating varnishes: Part 1
Electric strength method
304
IS 11256(Part 3):1985
Methods of test for determination of
IEC 60290(1969)
thermal endurance of insulating varnishes:
Part 3 Bond strength by helical coil method
305
IS 11260(Part 1):1985
Specification for Stabilized power supplies
ac output:
Part 1Ratings and performance .
IEC 60686(1980)
306
IS 11260(Part 2):1985
Specification for Stabilized power supplies
ac output:
Part 2 Tests
IEC 60686 (1980)
307
IS 11298(Part 1):1985
Plastic films for electrical purposes: Part 1
Definitions and general requirements
IEC 60674-1(1980)
308
IS 11322:1985
Method for partial discharge measurement
in instrument transformers
IEC 44-4 (1980)
309
IS 11353:1985
Guide for uniform system of marking and
identification of conductors and apparatus
terminals
IEC 60445(1973)
310
IS 11354:1985
Guide for identification by hour numbers of
the phase conductors of 3-phase electric
systems
IEC 60152(63)
311
IS 11530:1985
Voltage grading capacitor
IEC 60358 :1990
312
IS 11654(Part 1):1986
Flexible insulating sleeving:
IEC 60684-1(1980)
Part 1 Definitions and general requirements
313
IS 11675:1986
Button cells - Silver oxide
314
IS 11676:1995
Microwave ovens for household and similar IEC 60705(1988)
purposes
315
IS 11692:1986
Method of tests for electro-slag remelting
furnaces
IEC 27(CO)60
316
IS 11712:1986
Safety requirements for
electro-slag remelting furnaces.
IEC 27(CO)1959
317
IS 11731(Part 1):1986
Methods of test for determination of
IEC 60107(1981)
flammability of solid electrical insulating
materials when exposed to an igniting
source: Part 1 Horizontal specimen method
318
IS 11731(Part 2):1986
Methods of test for determination of
flammability of solid electrical insulating
materials when exposed to an igniting
source: Part 2 Vertical specimen method
IEC 60707(1981)
319
IS 11755:1986
Method of test for determination of
electrical resistance and resistivity of
insulating materials at elevated
temperatures
IEC 60345(1971)
320
IS 11756:1986
Method of test for co-efficients of friction of IEC 60648(1979)
plastic film and sheeting for use as
electrical insulation
321
IS 11955:1987
Preferred current ratings
322
IS 12026(Part 1):1986
Guide for the determination of the aromatic IEC 60590(1977)
hydrocarbon content of new insulating oils:
Part 1 Absorption chromatographic method
323
* IS 12065:1987
Permissible limits of noise level for rotating
electrical machines
ISO/IEC
IEC 60370(1971)
IEC 86-2(1982)
IEC 60059(1999)
IEC 60034-9
Sl. No. IS Number/ DOC Number
Title
324
Mechanical vibration of rotating electrical
machines with shaft heights 56 mm and
higher-measurement, evaluation and limits
of vibration severity (first revision)
* IS 12075:2008
ISO/IEC
325
IS 12083(Part 1):1986
Electrical relays: Part 1 Contact
performance
IEC 255-0-20 (1974)
326
IS 12083(Part 2):1986
Electrical relays: Part 2 Insulation tests
IEC 255-5 (1977)
327
IS 12289:1988
Hand held electric engraving tools
IEC 60745-1
328
IS 12312:1987
Inductive voltage dividers
IEC 60618
329
IS 12317(Part 1):1988
Ceramic and glass insulating materials for
telecommunication and allied purposes:
Part 1 General requirements and
classification of ceramic and glass
insulating materials
IEC 60672-1(1980)
330
IS 12346:1999
Testing equipment for ac electrical energy
meters
(first revision)
IEC 60736:1982
331
IS 12360:1988
Voltage bands for electrical installations
including preferred voltages and frequency
(superseding IS:585)
IEC 60038(1983)
332
* IS 12422:1988
Test method for oxidation stability of
inhibited mineral insulating oils
IEC 60474(1977)
333
IS 12449(Part 1):1988
Starting devices (other than glow starters):
Part 1 General and safety requirements
IEC 60926 (1995)
334
IS 12449(Part 2):1988
Starting devices (other than glow starters):
Part 2 Performance requirements
IEC 60927 (1996)
335
IS 12615:2011
Energy Efficient Three Phase Squirrel
Cage Induction Motors (Second Revision)
336
IS 12642:1989
Brush-holders for slip rings group R-Type
RA
IEC 60778
337
IS 12677:1989
Internal fuses for series capacitors
IEC 60595:1977
338
IS 12730:1989
Internal fuses and internal overpressure
disconnectors
for capacitors for inductive heat generating
plants
IEC 60594:1977
339
IS 12948:1990
Tungsten halogen lamps (non-vehicle)
IEC 60357(1982)
340
** IS 13010:2002
AC watt-hour meters, Class 0.5, 1 and
2(first revision)
IEC 60521:1988
341
IS 13021(Part 1):1991
AC supplied electronic ballasts for tubular
florescent lamps: Part 1 General and
safety requirements
IEC 60928(1990)
342
IS 13021(Part 2):1991
AC supplied electronic ballasts for tubular
florescent lamps: Part 2 Performance
requirements
IEC 60929(1990)
343
IS 13072:2013
Specification of technical grade Sulfur
hexafluoride (SF6) for use In electrical
equipment (First Revision)
IEC 60376:2005
344
IS 13203:1991
Method for verifying accuracy of tan-delta
measuremnts
IEC 60996:1989
345
IS 13236:2013
Insulating liquids - methods for counting
and sizing particles (First Revision)
IEC 60970:2007
346
IS 13263:1992
Methods of test for plasma equipment for
electroheat installations.
IEC 60680(1980)
347
IS 13315:1992
Nickel -cadmium batteries for electric
locomotives
IEC 623(1983)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
348
IS 13341:1992
Requirements for ageing test, self-healing IEC 60831-2:1988
test and destruction test on shunt
capacitors of the self-healing type for ac
power systems having a rated voltage upto
and including 650 V
349
IS 13364(Part 1):1992
Specification for ac generators driven by
reciprocating internal combustion engine:
Part 1 Rated up to 20 kVA
350
IS 13364(Part 2):1992
Specification for ac generators driven by
IEC 60341(1983)
reciprocating internal combustion engine:
Part 2 Rated above 20 kVA and upto 1250
kVA
351
IS 13466:1992
Specification for brushes for electrical
machines [superseding IS:3003 (Parts 3
and 4)-1977]
352
IS 13508:1992
Test procedure for measurement of loss of IEC 60894(1987)
tangent angle of coils and bars for machine
winding-guide
353
* IS 13529:1992
Guide on effects of unbalanced voltages
on the performance of three-phase cage
induction motors
IEC 600892(1987)
354
IS 13580:1992
Internal fuses and internal overpressure
disconnectors for power electronic
capacitors
IEC 60594:1977
355
IS 13584:1993
Specification for brush materials for
electrical machinery [Superseding IS
3003(Part 2):1977]
IEC 413(1972)
356
IS 13585(Part 1):2012
Shunt capacitors of the non-self-healing
IEC 60931-1:1996
type for ac systems having a rated voltage
upto and including 1 000 V - Part 1
General - performance, - Guide for
installation and operation (first revision of
IS 13585 (Part 1) (IEC 60931-1:1996)
357
IS 13586:1993
Definitions and nomenclature for carbon
brushes, brush holders, commutators and
slip rings for rotating electrical machinery
(superseding IS:3003(Part 1)-1977)
IEC 276(1968)
358
* IS 13631:2000
Method of test for detection and
determination of antioxidant additives in
insulating oils
IEC 60666(1979)
359
IS 13648:1993
Power electronics capacitors
IEC 61071-1:1991
360
** IS 13779:1999
AC static watthour meters (Class 1 and 2)
(first revision)
IEC 61036:1996
361
IS 13886:1993
Bimetallic thermostats and thermal
cutouts for use with electric irons
IEC 60730(1892)
362
IS 13925(Part 1):2012
Shunt capacitors for ac power systems
having a rated voltage above 1000 V : Part
1General performance, testing and rating
safety requirements - Guide for installation
and operation (superseding IS
2834:1986)(First Revision)
IEC 60871-1:2005
363
IS 13964:1994
Methods of measurement of transformer
and reactor sound levels
IEC 551 (1976)
364
IS 14122:1994
Built in thermal protection for electric
motors rated up to 660 V ac
IEC 60034-11(1978)
365
IS 14144:1994
Electric coffee makers
(Superseding IS 3514)
IEC 60661(1980)
IEC 60034-1
IEC 60136, 467, 773
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
366
IS 14155:1994
Domestic electric clothes washing
machines
for domestic use [Superseding IS
6390(Part 1):1983
and IS 6390 (Part 3): 1992]
IEC 60456(1974)
367
IS 14218:1994
Sealed cylindrical type rechargeable nickel
cadmium cells
IEC 285(1983)
368
IS 14256:1995
Rating specification for semiconductor
power
converters for adjustable speed electric
drive
systems - particularly for DC motor drives.
IEC 61136-1(1992)
369
IS 14257:1995
Lead-acid storage batteries for motor
IEC 95-1(1988)
vehicles with light weight and high cranking
performance
370
IS 14376:1996
Brush holders for electrical machines
IEC 136(1986)
371
IS 14415:1997
Volt-Amphere hour meters for restricted
power factor range - specification
[superseding IS:722 (Part 5):1980
IEC 60211:1996
372
IS 14451(Part 1):1998
Telemetering of consumption and demand: IEC 60338:1970
Part 1 Impulse transmitting and receiving
devices
373
IS 14451(Part 2):1999
Telemetering for Consumption and
Demands Part 2 Direct digital transfer of
meter values
IEC 60338:1970
374
IS 14479:1997
Electromagnetic compatibility of electrical
and electronic installation in ships
IEC 60 533:1999
375
** IS 14697:1999
ac static transformer operated watthour
and var-hour meters, class 0.2S and .5SSpecification
IEC 60687:1992
376
IS 14763:2000
Conduit for electrical purposes, outside
diameters of conduits for electrical
installations and threads for conduits and
fittings
IEC 60423(1993)
377
IS 14768(Part 1):2000
Conduit fittings for electrical installations
:Part 1 General requirements
IEC 61035-1(1990)
378
IS 14768(Part 2):2003
Conduit fittings for electrical installations :
Part 2 Metal conduit fittings (superseding
IS 2667)
IEC 61035-2-1(1993)
379
IS 14772:2000
Enclosures for accessories for household
and similar fixed electrical installations
(Superseding IS 5133(Part 1 and 2)
IEC 60670-1(1989)
Resistance trace heating in potentially
explosive atmospheres: Part 1 General
and testing requirements
IEC 62086-1
380
* IS 14774(Part 1):2000
381
IS 14774(Part 2):2000
Resistance trace heating in potentially
explosive atmospheres: Part 2 Informative
application guide for design, installation
and maintenance
IEC 62086-2
382
IS 14897:2000
Glass bulb designation system for lampsGuide
IEC 60887(1988)
383
IS 14902(Part 1):2013
Performance of high-voltage direct current
(HVDC) systems with line-commutated
IEC/TR 60619-1:2010
conditions ([First Revision)
Sl. No. IS Number/ DOC Number
Title
ISO/IEC
384
IS 14902(Part 2):2013
Performance of high-voltage direct current
(HVDC) systems with line-commutated
converters -- Part 2: Faults and switching
(First Revision)
IEC/TR 60619-2:2008
385
IS 14902(Part 3):2013
Performance of high-voltage direct current
(HVDC) Systems with line-commutated
IEC/TR 60619-3:2009
(First Revision)
386
IS 14927(Part 1):2001
Cable trunking and ducting systems for
electrical installations :Part 1 General
requirements
IEC 61084-1(1991)
387
IS 14927(Part 2):2001
Cable trunking and ducting systems for
IEC 61084-2-1(1996)
electrical installations: Part 2 Cable
trunking and ducting systems instended for
mounting on walls or ceilings
388
IS 14930(Part 1):2001
Conduit systems for electrical installations : IEC 61386-1(1996)
Part 1 General requirements
389
IS 14930(Part 2):2001
Conduit systems for electrical installations : IEC 61386-2(1995)
Part 2 Particular requirements for conduit
system buried underground
390
IS 15063:2001
Alkaline manganese dioxide cells
IEC 86-2(1994)
391
IS 15086(Part 3):2003
Surge arresters: Part 3 Artificial pollution
testing of surge arresters
IEC 60099-3:1990
392
IS 15111(Part 1):2002
Self ballasted lamps for general lighting
services :
Part 1 Safety requirements
IEC 60968(1988)
393
IS 15111(Part 2):2002
Self ballasted lamps for general lighting
services :
Part 2 Performance requirements
IEC 60969(1988)
394
IS 15518(Part 1):2004
Safety requirements for incandescent
lamps :
Part 1 Tungsten filament lamps for
domestic and
similar general lighting purposes
IEC 60432-1 (1999)
395
IS 15687(Part 1):2006
Single-capped fluorescent lamps: Part 1
Safety requirements
IEC 61199 (1999)
396
IS 15787:2008
Switch- socket outlets (Non-Interlock Type) IEC 60884-2-3 (1989)
397
IS 15885(Part 1):2011
Safety of lamp controlgear: Part 1 General
requirements
398
IS 15885(Part 2/Sec
1):2011
Safety of lamp controlgear: Part 2
Particular requirements, Sec 1 Starting
devices (other than glow starters
399
IS 15885(Part 2/Sec
3):2011
Safety of lamp controlgear: Part 2
IEC 61347-2-3 (2000)
Particular requirements, Sec 3 ac supplied
electronic ballasts for fluorescent lamps
400
IS 15885(Part 2/Sec
8):2011
Safety of lamp controlgear: Part 2
IEC 61347-2-8 (2000)
Particular requirements, Sec 8 Ballasts for
fluorescent lamps
401
IS 15885(Part 2/Sec
9):2011
Safety of lamp controlgear: Part 2
IEC 61347-2-9 (2000)
Particular requirements, Sec 9 Ballasts for
discharge lamps (excluding fluorescent
lamps)
402
IS 15967(Part 1):2013
Capacitor for use in tubular fluorescent
and other discharge lamps circuits : Part
1 Safety requirements
IEC 61347-2-1 (2000)
Sl. No. IS Number/ DOC Number
Title
403
IS 15967(Part 2):2013
Capacitor for tubular fluorescent lamps:
Part 2 Performance requirements
404
IS 15968:2013
Ballasts for tubular fluorescent lamps Performance requirements
405
IS 16071:2013
High-voltage direct current (HVDC)
ISO/IEC
IEC 62001:2003
and design evaluation of a.c. filters
406
IS 16075:2013
Voltage sourced converter (VSC) Valves
for high-voltage direct current (HVDC)
(IEC 62501:2009
407
IS 16076:2013
High-voltage direct current (HVDC)
IEC 61975:2010
408
IS 16082:2013
Insulating liquids - Contamination by
polychlorinated biphenyls (PCBs) - Method
of determination by capillary column gas
chromatography
IEC 61619:1997
409
IS 16083:2013
Specification for unused insulating mineral
oils for cables with oil ducts
IEC 60465:1988
410
IS 60320(Part 2/Sec
3):2007
Appliance couplers for household and
similar general purposes- part 2-3
Appliance coupler with a degree of
protection higher IPXO
IEC 60320-2-3(1998)
Total : EQUIVALENT STANDARDS = 410
ANNEX 3
BILINGUAL STANDARDS
Sl. No. IS Number/ DOC Number
Title
1
IS 2412:1975
Link clips for electrical wiring (first revision)
2
IS 12762(Part 9):2010
Photovoltaic devices: Part 9 Solar simulator performance requirments
ASPECT WISE POSITION OF STANDARDS
PRODUCT
894
METHODS OF TEST
230
CODE OF PRACTICES
152
TERMINOLOGY
57
DIMENSION
47
SYMBOLS
19
OTHERS
84
TOTAL : 1483