LED and Fluorescent
High Bays
FP-HB Food Processing Series
30” x 48” 8 Lamp Sealed High Bay Luminaires for Pendant, Chain or Surface Installation
ISO-5, 209E Class 100 Cleanspaces
Specifications:
Housing: Optimized for water shedding, one
piece 20 ga. welded stainless steel or aluminum.
Seam welded seams.
Door Frame: One piece 20-gauge aluminum or
type 304 stainless steel one piece inset door frame
hinged to housing with 2 stainless steel cables.
Secured by captive stainless steel screws. Hose
Down 1700 PSI optional.
Lens: Clear .125” thick virgin acrylic set in NSF
silicone sealant.
Electrical: Standard two, four lamp instant start
ballasts for T8. Electronic less than 10% THD high
performance instant start universal voltage (120277 volt). See options for other choices.
Reflector: High reflectance white (92% refl.)
white polyester powder coatings over steel.
Lamps: T8 or T5HO type. Lamps are supplied by others unless specified below.
Gaskets: NSF listed closed microcellular
extruded one piece SealPro gasket seals door
frame to housing. Oil and solvent resistant
gasket system.
Project: _________________________________________
Fixture Type: _____________________________________
Cat. Number: _____________________________________
Approved by: _____________________________________
Installation: Pendant, Y-Cable or Chain mount
systems available. Power entry through sealed access plate knockouts on rear of fixture at center.
Standard
Finish: White polyester powder coating over
steel, and aluminum housings. Rated 1000hr Salt
spray corrosion protection over steel. Stainless steel housings and door frames are satin
polished.
WET LOCATION
209E
100
Listings: UL & CUL listed for wet locations.
IP-65 water and dust protection. Federal Standard
209E, ISO 14644-1 Class 5, Cleanroom rated class
100. NSF Non-Food zone. NSF Food Zone for
stainless steel construction.
ISO
5
NSF
ISO 14644-1
CLASS 5
C-2 FOOD ZONE
NSF
FED STD 209E
CLASS 100
Optional
1700
PSI
Hosedown
Rated
NON FOOD ZONE
IP
65
IEC 60529
30”
4.45”
2”
Uplight
Option
30”
Ordering Information: Ex: FP-HB-3-40-8/T5HO-120V-HIA-CP5-15P
FP
-
Series Installation Type
FP
HB - HB = Sealed Highbay
40 = 30”x48” Housing
- 40 Material
1 = CRS Hsg. & CRS Door
2 = CRS Hsg. & SS Door
3 = SS Hsg. & SS Door ‡
4 = AL Hsg. & SS Door
5 = AL Hsg. & AL Door
6 = CRS Hsg. & AL Door
Size
48”
-
Lamps
-
-
Voltage Elect. Options
120V
277V
347V*
UNV*
6 or 8/T8 = F32T8 32W T8 (G13) 0°F Starting
6 or 8/T5 = F28WT5 28W T5 (G5)* 0°F Starting
6 or 8/T5HO = F54WT5 54W T5HO (G5)* -20°F Starting
FF = Fuse & Holder
FD = Double Fuse & Holders
2/EB = Two Ballasts, (Two Circuits)
EBL = -20°F Electronic Ballast
EBPRS = Program Rapid Start Ballast
EBDIM = Electronic Dimming Ballast
HLO = High Light Output Ballast (>1.15 BF)*
1/EM = 1 Lamp Battery Pack (700L)
2/EM = 1 or 2 Lamp Battery Pack (1400L)*
Kurtzon Lighting / Innovators in Lighting Since 1898
General Options
TP = Stainless Steel Tamperproof Fasteners
WHT = White Finished Stainless Steel
HD1700 = 1700 psi Hosedown
HIA = .140" P12 Prismatic High Impact Acrylic
CP = .125" Clear Smooth Polycarbonate
LEX = .125" P12 Prismatic Polycarbonate
OCC = Wet Location Occupancy Sensor
Lz = Lamps Provided Where “z”= lamp details
UPL= 5% Uplight, Sealed Lenses (2)
Cord Options
CPx = Six Foot Cord and Plug(**)
LCPx = Six Foot Locking Cord and Plug(**)
Note: Not all options are compatible with every
*options
option. Consult factory for additional Lamp options &
marked "*".
**
Note: Cord and plug options are not water tight
connections. A sealed cord bushing is provided
at the fixture when a cord is specified. Replace the
"x" above with the NEMA cordset designation. 5-15P
is standard for 120v and 7-15P is for 277v. For wet
locationscordsetsandothercordoptionspleasecontact
the factory.
‡ Only #3 material is NSF Food Zone. All other materials are non-food zone.
Morris Kurtzon, Incorporated
1420 South Talman Avenue, Chicago, Illinois 60608
773/277-2121 FAX 773/277-9164
© 2013
FP-HB
Food Processing Series
2x4 6 Lamp Sealed Luminaires for High Bay Surface Installation
ISO-3, 209E Class 1 Cleanspaces using T5, T5HO, T8 and LEDs
Specifications:
Project: _________________________________________
Housing: One piece, seam welded, hole free
20-gauge CRS, stainless steel or aluminum construction. Stainless steel is satin polished unless
WHT option is chosen.
Gaskets: NSF Listed closed cell microcellular
extruded KleanLock SealPro™ with vulcanized
corners making a one-piece oil and solvent
resistant gasket.
Door Frame: 20-gauge CRS, Aluminum or type
304 stainless steel one piece overlapping door frame
hinged to housing with two stainless steel cables.
Secured by captive stainless steel screws.
Electrical: Standard ballast - Electronic less
than 10% THD high performance instant start
universal voltage (120-277 volt). Sealed cord and
plugs available in NEMA and proprietary wet location types. See options below for choices.
Lens: High durability .135” thick virgin acrylic with
P12 prismatic pattern inverted (smooth side out).
See “Options” for other choices.
Lamps:T8 or T5HO type. Lamps are supplied
by others unless specified below.
Reflector: Die formed specular aluminum high
reflectance anodized finish. (minimum reflectivity
94%)
Installation: Four .312” holes for surface mounting. Two .875” flattened and silicone sealed knockouts for wiring. See below for mounting options.
Suitable for through wiring.
Fixture Type: _____________________________________
Cat. Number: _____________________________________
Approved By: _____________________________________
Standard
Optional
ISO
3
WET LOCATION
Finish: Gloss white high reflectance 1000 hr.
salt spray polyester powder coat finish standard
for all CRS and aluminum housings. Stainless
steel housings and doorframes are satin polished
unless option WHT is chosen.
209E BSL
1
ISO
6
Bio Safety Levels
ISO 14644-1
CLASS 6
1&2
FED STD 209E
CLASS 1
IP
66
Listings: UL and CUL Listed for Wet Locations.
Cleanroom ISO14644-1 Class 3 (Fed Std-209E
class 1), Bio-safety level 3 & 4. High pressure
washdown to 1700 psi. IEC 60529 IP-66 dust and
water resistant. NSF-2 Food Zone ‡ or non-food
zone. Optional Class I , Div. 2 Groups A, B, C, and
D hazardous location listing.
ISO 14644-1
CLASS 3
Hazardous Location
Class 1 Division 2
Bio Safety Levels
BSL
3&4
NSF
IEC 60529
C-2 FOOD ZONE
1700
PSI
Hosedown
Rated
Installation Detail
Cross Section
4.50”
24” x 48”
14.0”
(4) .312” Holes
(2) .875" KO's
Gasketed
Access Cover
24”
36”
48”
Ordering Information: Ex: FP-HB-3-2x4-6/T5HO-120V-PA-CP5-15P
FP
-
Series Installation Type
FP
HB -
HB = Sealed Highbay
2x4 = 2'x4’ Housing
- 2X4 Material
Size
-
Lamps
1 = CRS Hsg. & CRS Door
2 = CRS Hsg. & SS Door
3 = SS Hsg. & SS Door ‡
4 = AL Hsg. & SS Door
5 = AL Hsg. & AL Door
6 = CRS Hsg. & AL Door
Voltage
Elect. Options
120V
277V
347V*
UNV*
4 or 6/T8 = F32T8 32W T8 (G13)
4 or 6/T5 = F28WT5 28W T5 (G5)*
4 or 6/T5HO = F54WT5 54W T5HO (G5)*
3/LEDR35 = Three 3500K Arrays producing 10,400 lumens
3/LEDR40 = Three 4000K Arrays producing 10,400 lumens
FF = Fuse & Holder
FD = Double Fuse & Holders
2/EB = Two Ballasts, (Two Circuits)
EBL = -20°F Electronic Ballast
EBPRS = Program Rapid Start Ballast
EBDIM = Electronic Dimming Ballast
HLO = High Light Output Ballast (>1.15 BF)*
1/EM = 1 Lamp Battery Pack (700L)
2/EM = 1 or 2 Lamp Battery Pack (1400L)*
Kurtzon Lighting / Innovators in Lighting Since 1898
General Options
TP = Stainless Steel Tamperproof Fasteners
WHT = White Finished Stainless Steel
PMB = Pendant Mount Bracket
HIA = .140" P12 Prismatic High Impact Acrylic
CA = .125" Clear Smooth Acrylic
LEX = .125" P12 Prismatic Polycarbonate
OCC = Wet Location Occupancy Sensor
Lz = Lamps Provided Where “z”= lamp details
Cord Options
CPx = Six Foot Cord and Plug(**)
LCPx = Six Foot Locking Cord and Plug(**)
Note: Not all options are compatible with every
*options
option.ConsultfactoryforadditionalLampoptions&
marked "*".
**
Note: Cord and plug options are not water tight
connections. A sealed cord bushing is provided
at the fixture when a cord is specified. Replace the
"x" above with the NEMA cordset designation. 5-15P
is standard for 120v and 7-15P is for 277v. For wet
locations cordsets and other cord options please
contact the factory.
‡ Only #3 material is NSF Food Zone. All other materials are non-food zone.
Morris Kurtzon, Incorporated
1420 South Talman Avenue, Chicago, Illinois 60608
800/837-8937 FAX 773/277-9164
© 2013
EL-HB
Basic Clean Space
2x4 6 Lamp Sealed Luminaires for High Bay Surface Installation
ISO-5, 209E Class 100 Cleanspaces using T5, T5HO, T8 and LEDs
Specifications:
Project: _________________________________________
Housing: One piece, seam welded, hole free
20-gauge CRS, stainless steel or aluminum construction. Stainless steel is satin polished unless
WHT option is chosen.
Gaskets: Neoprene, 100% pure, closed cell
located at interface of door to housing and door to
lens. See Option “GG” for SealPro™ NSF Listed
closed cell gasketing.
Door Frame: 20-gauge CRS, aluminum or type
304 stainless steel channel door frame hinged to
housing with two stainless steel cables. Secured by
captive stainless steel screws.
Electrical: Standard ballast - Electronic less than
10% THD high performance instant start universal
voltage (120-277 volt). Sealed cord and plugs available in NEMA and proprietary wet location types. See
options below for choices.
Lens: High durability .135” thick virgin acrylic with
P12 prismatic pattern inverted (smooth side out).
See “Options” for other choices.
Lamps: T8 or T5HO type. Lamps are supplied by
others unless specified below.
Reflector: Die formed specular aluminum high
reflectance anodized finish. (minimum reflectivity
94%)
Installation: Four .312” holes for surface mounting. Two .875” flattened and silicone sealed knockouts for wiring. See below for mounting options.
Suitable for through wiring.
Fixture Type: _____________________________________
Cat. Number: _____________________________________
Approved By: _____________________________________
Standard
ISO
5
Finish: Gloss white high reflectance 1000 hr. salt
spray polyester powder coat finish standard for all
CRS and aluminum housings. Stainless steel housings and doorframes are satin polished unless option
WHT is chosen.
ISO 14644-1
CLASS 5
WET LOCATION
NSF
NON FOOD ZONE
Bio Safety Levels
209EISO
6
100
ISO 14644-1
CLASS 6
FED STD 209E
CLASS 100
Listings: UL and CUL Listed for Wet Locations.
Cleanroom ISO14644-1 Class 5 (Fed Std-209E
class 100), Bio-safety level 1 & 2. IEC 60529 IP-55
water and dust resistance. Washdown resistance
rated to 85 psi. Optional Class I , Div. 2 Groups A,
B, C, and D hazardous location listing.
Optional
BSL
1&2
Hazardous Location
Class 1 Division 2
IP
55
HOSE DOWN
IEC 60529
RATED
85
PSI
Installation Detail
Cross Section
4.50”
14.0”
24” x 48”
(4) .312” Holes
(2) .875" KO's
Gasketed
Access Cover
24”
36”
48”
Ordering Information: Ex: EL-HB-4-2x4-6/T5HO-120V-HIA-CP5-15P
EL
-
Series Installation Type
EL
HB
HB = Sealed Highbay
2x4 = 2'x4’ Housing
-
- 2X4 -
Material
Size
-
Lamps
1 = CRS Hsg. & CRS Door
2 = CRS Hsg. & SS Door
3 = SS Hsg. & SS Door
4 = AL Hsg. & SS Door
5 = AL Hsg. & AL Door
6 = CRS Hsg. & AL Door
Voltage
120V
277V
347V*
UNV*
4 or 6/T8 = F32T8 32W T8 (G13)
4 or 6/T5 = F28WT5 28W T5 (G5)*
4 or 6/T5HO = F54WT5 54W T5HO (G5)*
3/LEDR35 = Three 3500K Arrays producing 10,400 lumens
3/LEDR40 = Three 4000K Arrays producing 10,400 lumens
FF = Fuse & Holder
FD = Double Fuse & Holders
2/EB = Two Ballasts, (Two Circuits)
EBL = -20°F Electronic Ballast
EBPRS = Program Rapid Start Ballast
EBDIM = Electronic Dimming Ballast
HLO = High Light Output Ballast (>1.15 BF)*
1/EM = 1 Lamp Battery Pack (700L)
2/EM = 1 or 2 Lamp Battery Pack (1400L)*
Kurtzon Lighting / Innovators in Lighting Since 1898
Elect. Options
General Options
GG = Listed Non Food Zone
TP = Stainless Steel Tamperproof Fasteners
WHT = White Finished Stainless Steel
PMB = Pendant Mount Bracket
HIA = .140" P12 Prismatic High Impact Acrylic
CA = .125" Clear Smooth Acrylic
LEX = .125" P12 Prismatic Polycarbonate
OCC = Wet Location Occupancy Sensor
Lz = Lamps Provided Where "z"= lamp details
Cord Options
CPx = Six Foot Cord and Plug(**)
LCPx = Six Foot Locking Cord and Plug(**)
Note: Not all options are compatible with every option.
*marked
Consult factory for additional Lamp options & options
"*".
**
Note: Cord and plug options are not water tight connections. A sealed cord bushing is provided at the fixture
when a cord is specified. Replace the "x" above with the
NEMA cordset designation. 5-15P is standard for 120v and
7-15P is for 277v. For wet locations cordsets and other cord
options please contact the factory.
Morris Kurtzon, Incorporated
1420 South Talman Avenue, Chicago, Illinois 60608
773/277-2121 FAX 773/277-9164
© 2013