TYPE:
CATALOG #:
COMMERCIAL
NOTES:
Provider™
PRO-2N/PRO-3N
6 Volt Thermoplastic Housing
Features
Suggested Specification
• Completely self-contained, thermoplastic construction with a polycarbonate
lens that protects the fully-adjustable self-locking heads
• Available with sealed, maintenance-free Lead-Calcium batteries
• Integrated circuitry offers 120/277VAC 60Hz standard operation, LED pilot
light rocker type, test switch, temperature compensated, low voltage battery
disconnect, brownout protection and lock out (automatic battery connect)
• Optional MR16 LED lamps
•Optional advanced diagnostic circuitry monitors every critical function of the
unit and provides an audible and visual indicator when a fault is detected
(non-audible versions available)
•Optional tamper-proof screws
• Optional NEXUS® wired and NEXUS® wireless systems
• Universal wall mounting pattern keyhole slots and a conduit
knockout provide alternate mounting methods
• Optional ceiling mount includes safety wire and pre-machined housing to
receive a securement screw.
• UL924 Listed
• UL924 Listed for use in Damp Locations
• 3-year limited warranty
Supply and install Emergi-Lite® Model PRO-2N/PRO-3N, 6 volt,
10.8-18 watts emergency lighting unit. Unit shall be fully automatic,
selfcontained, maintenance-free and listed to UL Standard 924.
Circuitry- shall include a 120/277 volt dual input transformer, automatic
charging, instantaneous transfer, test switch, long life LED AC charge
monitor light. The charger shall utilize a computer tested integrated
circuit which samples the battery in relation to its temperature, state
of charge and input voltage fluctuations. The charger shall be current
limited, temperature compensated, shortcircuit protected and reverse
polarity protected. The charger shall recharge the battery to rated
capacity as per UL924 specifications. Electrical features shall include a
Low Battery Voltage Disconnect circuit to protect the battery from deep
discharge damage. Brownout protection for automatic unit operation
when utility power drops low enough to dim incandescent lamps and
extinguish fluorescent and HID lamps. Battery lockout feature to prevent
battery discharge during installation to a non-energized circuit.
Battery- shall be 6 volt, maintenance-free and have the electrolyte in a
sealed case. To prevent loss of electrolyte through gassing, the battery
shall operate by the principle of electrolyte recombination.
Detailed warranty terms located at: www.emergi-lite.com/usa/files/EL_Warranty.pdf
Advanced Diagnostics (optional)
Housing- Heads and Shield- The housing and heads shall be constructed
of high impact, UL 94-5VA flammability off white thermoplastic. The unit
shall resist denting, peeling, scratching and corrosion. Heads shall have
High Intensity Tungsten (HIT) lamps mounted in polished reflectors. The
transparent lamp shield shall be constructed of acrylic.
Enjoy the peace of mind provided by Emergi-Lite’s advanced diagnostic
circuitry. The AD circuit monitors the every critical function of the unit
and provides an audible and visual indicat or when a fault is detected.
Non-audible versions available as well.
Mounting- The unit shall be mountable in any orientation, on walls or
ceilings. A universal mounting pattern, rear key-hole slots, and conduit
entry on one end shall be provided. The lamp shield, housing and
backplate shall be designed for snap-together assembly to eliminate
screws and facilitate easy installation.
Unit Warranty
Entire unit (excluding lamps, fuses and pilot ) carries a 3-year Full
Warranty.
Accessories (order as a separate item)
The unit shall be Emergi-Lite® model:
SUFFIX
DESCRIPTION
Replacement lamps
570.0012-E
Additional special bit for tamper-proof screws
690.0454-E
REPLACEMENTS LAMPS
570.0012-E
HIT 6V-5.4W
580.0097-E
MR16 LED 6V-4W
Power Consumption and Unit Rating
Each unit are furnished with one HIT lamp per head.
PROVIDER™ BATTERY UNIT
Sealed MaintenanceD.C. Voltage
Free Battery Types
Lead-Calcium
Model
Number
Watts to 87-1/2% of rated battery
voltage
2 hrs 3 hrs
4 hrs
6
PRO-2N
10.8
1-1/2 hrs
8.5
–
–
6
PRO-3N
18
12
10
7
*National Electrical Code Specification
17
.
COMMERCIAL
Fast and Easy Installation
Dimensions
Dimensions are approximate and subject to change.
Snap-together design eliminates screws.
7
3
58"
114"
11-3/4”
5"
5-7/8”
5”
Keyhole slot
Conduit knockout
Universal mounting pattern
AC-quick connect plug
Provider’s AC quick-connect plug, battery lock out feature and snaptogether design make installation fast and easy.
With the AC quick-connect plug, contractors simply make the AC
connection to the plug, mount the back plate and plug in the unit.
The battery lock out feature is an AC activated load switch that prevents
the batteries from discharging until the unit is energized with AC power.
This allows the contractor to install the Provider™ and connect the
batteries in one convenient operation.
Universal mounting pattern keyhole slots and a conduit knock out
provide alternate mounting methods.
How to Order
COLOR
Blank= Off white
B= Black
SERIES
PRO-2N= 6V-10.8W
PRO-3N= 6V-18W
LAMP TYPE
UNIT TYPE
-LA= 6V-4W, MR16 LED
-ZP= mini tungesten, 6V-5.4W
OPTIONS
Blank= Standard Unit
-AD= Advanced Diagnostics (audible)
-ADNA= Advanced Diagnostics (non-audible)
NEX= NEXUS® wired*
NEXRF= NEXUS® wireless*
V= Voltmeter *
DL= Damp Location
VR= Vandal-resistant screws
C= Line Cord 120V
CM= Ceiling mount - Supplied with metal harness
*Available with PRO-2N only.
*Available with Standard unit type only.
SCALE 1:3
Example: BPRO-2N-LADL
All information and specifications contained in this specsheet are subject to change due to engineer design, errors and omissions.
Illustrations and diagrams within this specsheet may vary from actual products.
19
2016© Thomas & Betts Limited. All rights reserved.