PRICE - BID
Telecommunication and other associated works in KZJ-BZA-BPQ section in SC Division / BZA Division of South
Central Railway.
Tender No.TCIL/01/021/268/I/2K14-SR, dt.03/12/2014.
No SOR No
Description
Qty
Unit
RATE
AMOUNT
Schedule A-1-Supply portion-SOR Items
1
1102
Supply of Thermo shrinkable jointing kit as per spec. no. IRS TC.
77/2010 (Rev 2) Inspection by RDSO
385
Nos
1660.85
639427.00
2
1104
Supply of 0.5 mm annealed tinned copper conductor PVC
insulated and PVC sheathed switch board telephone cable, 10
pair, as per Specn. No. TC 24/91 Inspection by consignee
1000
RMT
26.77
26770.00
3
1106
Supply of desk type 2 wire, 12 way DTMF selective calling group
telephone complete as per specification IRS. TC. 80-2000 with
suitable power supply unit. Inspection by RDSO
70
Nos
5425.60
379792.00
4
1136
Supply of analog insulation tester Meco model No MC 941500V/ 1000M. Ohms or similar. Inspection by Consignee
4
Nos
3007.31
12029.00
5
201
Supply of GKP type Location Boxes Full size as per drg. No.
S&T/MFT/ 2378 (Single) Inspection by RITES
260
Nos
7738.52
2012015.00
6
204
Supply of `E' type locks of different wards as per requirement
with key per E- type lock to Drg. No. SA.3376/M/ Latest and
RDSO Specn. No. IRS. S.30/64. Inspection by RITES
260
Nos
483.66
125752.00
7
1129
Supply of one quad V.F. Transformer assembly (2T) to RDSO
Spec. No. IRS: TC. 76 -2000 with Amdt.1 (or latest) with
impedance ratio 470:1120 Ohms. Inspection by RDSO
300
Nos
610.62
183186.00
8
1135
Digital Multimeter Fluke or Rishab 15S. Inspection by Consignee
4
Nos
4940.22
19761.00
9
1127
100
Roll
2126.37
212637.00
10
1808
225
Nos
1316.24
296154.00
11
1137
4
Nos
16883.96
67536.00
12
705
1
Nos
118323.30
118323.00
13
1133
100
Nos
1094.28
109428.00
30
sets
6581.20
197436.00
14
1145
supply of 12 pair weather proof C.T. Box for station SP/SSP/TSS
etc. locations. Inspection by Consignee
Vulco tape of size 45mm width x 1.5 mm thick x 10 Mtr. length.
It shall be self bonding type anti corrosive, heat resistant &
water proof. Inspection by consignee
Supply of Transmission measurement set APLAB Make Model
No. 2031A Complete with tone Generator and dB meter.(Refer
technical specification) Inspection by consignee
Supply of Cable Route locator consisting of Cable Avoidance
Tool XD(ST CAT 33XD),SGV Signal Generator(ST-SGV33) and
Signal Clamp Accessory(ST-SC) in a carrying bag (ST-CB) .
Inspection by Consignee
Supply of emergency socket box to RDSO drg no 15220 with
socket six pin flat ot RDSO spec No IRS TC.42/87.Amd.1 or
latest. Inspection by consignee
Supply of 15 U rack wall mounted of VERO President make or
similar with cooling fan, power manager with 5 sockets, 1
equipment tray, earth connecting kit. (b) Wago terminal one
set fitted on DIN rail consist
c. part no. 280-101 Qty 32 nos (terminals)
d. part no. 280-301 Qty 4 nos (end plate).
Inspection by consignee
Page 1 of 5
No SOR No
15
1601
Description
Qty
Unit
Supply of basic material to construct unit maintenance free
earth consisting as per RDSO spec no. RDSO/SPN/ 197/2008
consisting of
a) copper bonded steel electrode of 3.0m long, 17.0 mm dia
with copper bonding thickness mini 250 micron and UL listed
and marked--1 no.
b)Earth enhancement compound of RDSO approved brand
supplied in sealed bags of min 10 Kgs-03 No.
c) Copper strip of 150X25x6mm to terminate earth rod-1 No.
d) Copper strip of 300X25x6mm (MEEB)-1 No.
e) Copper strip of 150X25x6mm(SEEB)-1 no
Cadmium bronze cable of size 3/16"
Earth electrode and coupler along with earth enhancin
85
sets
RATE
14541.68
AMOUNT
1236043.00
5636289.00
TOTAL
Schedule A-2-Supply portion -NS items
Digital Earth Resistance Tester Model No. DET 10-20 Ohms of
make Electronics device or similar. Inspection by Consignee
1
Supply of Digital Earth tester along with test kit and leather
case similar to CIE make, Model No.DET-2000.- Refer technical
specifications Inspection by consignee
Supply of Rodometer shall consists of one metre circumference
wheel with folding handle, carrying bag and measure up to
9999.9 metres-- Refer technical specifications Inspection by
Consignee
Networking monitoring system complete
Inspection by Consignee
2
3
4
4
Nos
2547.84
10191.00
4
Nos
2923.54
11694.00
3
Nos
2461.47
7384.00
2
Nos
47316.34
94633.00
123902.00
TOTAL
Schedule B.1 – Labour portion SOR Items
1
2
3
1902
Excavation of trench to a depth of 1200 mm and width of 300m
at bottom in all types of soil (Normal soil/soft soil/sandy soil
except in hard morum/ rocky soils/bridges/ level crossings/
track crossings/ coil pits,) as per RDSO Sketch no. SDO/ CABLE
LAYING/003
165
RKM
46194.67
7622121.00
1903
Excavation of trench to a depth of 1200 mm and width of 300m
at bottom in hard morum soil as per RDSO Sketch no
SDO/CABLE LAYING/003 including marking of cable alighment,
clearing of jungle, bushes, trial pits if required, refilling with
excavated soil, ramming and consolidation after laying of cables
complete to the finished item of work as directed by supervisor
in-charge.
70
RKM
59702.82
4179197.00
1904
Cutting of rock up to a depth of 300 mm and width of 300mm
where rock is visible from surface, concreting to ground level
after laying cables with 1 cement: 2 sand: 4 graded stone
aggregate 20mm nominal size and curing of concrete to the
required number of days, Drg. No. SK/CN/NEW/1. All the
material is to be arranged by contractor.
2020
RMT
409.34
826867.00
Page 2 of 5
No SOR No
Description
Qty
Unit
RATE
AMOUNT
4
Cutting of rock up to a depth of 200 mm and width of 200 mm
where rock is visible from surface to a depth more than 300
mm up to 550 mm, excavation of trench with width 300mm
above rock concreting 200mm x 200mm after laying of cable
1905-01 with 1 cement: 2 sand: 4 graded stone aggregate 20mm
nominal size and curing of concrete to the required number of
days, refilling with excavated soil ramming and consolidation
Drg. No. SK/CN/ NEW/3. All the material is to be arranged by
contractor.
4000
RMT
214.46
857840.00
5
When rock is visible fore more than 0.5 metre and up 0.8 metre
from ground level, excavating the trench minimum 0.5 metre
and maximum 0.8 metre, laying 6-quad cable as per the details
1905-02
11000
shown in drawing no. 3 and concreting 200 mm x 200mm over
the rocky surface after leveling with soil / sand . (Chase cutting
not required).
RMT
177.97
1957670.00
6
3502
Straight through / derivation with/ without transformer joints:
Installation Thermo shrinkable jointing kits for straight through
/ derivation joints for LC gate, pump houses etc where VF
transformers are not required and derivation joint by using 2T
transformer (to be housed in the joint).
450
Nos
871.18
392031.00
7
1909
Breaking of metal/tar road and refilling after laying the cables
as per drawing no. SDO/CABLE LAYING/010. The surface of the
road shall be concreted to match with the old surface.
1100
RMT
126.36
138996.00
8
Foundations, erection, fixing of 'E' type locks, painting the box
and painting of termination & other particulars of the following
boxes. Metal Size of the aggregate should not be more than
2001/01 40mm. Work to be done as per prescribed drawing no.
SK/CN/1/89-A & B - All the material is to be arranged by the
contractor except E-type lock (E-type lock will be supplied by
Rlys.).
260
Nos
2189.07
569158.00
9
1920
Supply, laying and installation of RCC pipe of 100/150 mm
outer dia., (standard length of 2 meteres and thickness of 25
mm) as protection for 6 quad cable under culverts / bridges,
track crossings, road crossing at LC etc.
2400
Nos
201.10
482640.00
10
1907
Track crossing by horizontal boring method based on the
drawing no. DRM/J/6735 dated 07-08-03 (enclosed) and as
advised by the engineer at site.
1800
RMT
1248.48
2247264.00
11
1908
Trenching under Rails for crossing the track (Track crossing) and
refilling of trenches as per RDSO drawing No. SDO/CABLE
LAYING/ 009. The track crossing shall be done at right angles,
the depth of cable trench shall be 1.2 Mtr. Below the rail
flange. The depth between top cable and the level of rail flange
of the rail shall never be less than 1.0m.
200
MTRS
125.47
25094.00
12
1910
Laying of different cables.
245000
MTRS
4.45
1090250.00
1924
Supply and fixing of MS-'C' channel of size 100mm x 50mm x
1200mm with suitable clamps as per drawing No. S&T/RE/78/2
/76 and fitting to GI pipe 65/50mm (to be supplied by Railways)
of spec. IS-1239/Part-1/Light with couplings and with suitable
clamps on Girder Bridges without drilling holes in the girders.
900
Nos
440.48
396432.00
1914
Excavation of square coil pit up to a depth of 1 Mtr. X 1.5 Mtr.
for providing coil at location box, point, signals etc. This
includes back filling and ramming of trench/pit after laying the
cable and consolidation of soil.
470
Nos
161.07
75703.00
13
14
Page 3 of 5
No SOR No
Description
Qty
Unit
2101
Excavation of earth and providing earth pipe of size 50mm dia,
3.5mm thick 2.0 m. long G.I. pipe with masonry tub constructed
around at earth locations as specified by site Engineer.
Alternate layers of 30kgs-chrcoal and 30kgs-common salt to be
filled in the pit while closing. The pipe perforation etc., to be
carried out as per drawing No. G/SG/09/2002.
30
Nos
1251.15
37535.00
3524
Fixing of 12 pair WAGO type CTB (CTBs will be supplied by
Railways) and termination of jelly filled cable as per details
given by Railway engineer at site at LC Gates/Pump Houses on
Teak wood plank of size 13"x8"x1".
100
Nos
193.10
19310.00
17
1921
Transporting and supply and installation of Concrete (RCC)
route indicators as intervals of 50 meters as per technical
specification. They should be of standard RCC with letters "SCR
S&T cable" as per type of cable laid to drawing.
5000
Nos
242.04
1210200.00
18
1926
Cutting of masonary walls at stations, cabins buildings and
other locations as indicated by Railway engineer at site to a
depth of 0.75m and supplying and fixing 50mm GI pipe.
75
Nos
542.82
40712.00
19
2102
Earthing and soldering of cable armour.
150
PER CABLE
18.68
2802.00
15
16
RATE
AMOUNT
20 2701/02
Transportation of materials from any Stores to Site and vice160000
versa including loading and unloading. - Lead above 50 Kms
PTPK
4.27
683200.00
21
Installation of single earth(maintenance free) including the
following:- welding and fixing of copper tape (used as bus bar)
welding of cadmium bronze cable to copper plate using
material supplied vide item no. 1,2 of SPD of Sch-A . All the
material supplied for mounting of copper tape, exothermic
weld materials, tools and fixtures for welding copper tapes shall
be
arranged
by
contractor.
a. Digging /Auguring/Boring of single earth pit of 100mm to
125 mm dia to the depth of approx. 2.8 meter.
b.
Insertion of 3.0 meter electrode and penetrating it at least .2
meter by pushing gently with sledge hammer where the natural
soil
is
assumed.
c. Filling of earth pit with earth enhancement compound (EEC)
in slurry from and backfilling.
d.
Carrying out exothermic weld connection on single earth
electrode to a copper tape of 150X25X6mm.
e.
SETS
3805.06
323430.00
2103
85
23178452.00
TOTAL
3
1
NS
2
NS
3
NS
Schedule B-2, Labour portion NS Items
Supply and laying of Double walled corrugated pipe (in already
prepared trench) of Poly Ethylene of size 77mm outer dia. And
63 mm inner dia. As per ISI spec. IS14930 Part-2 (2001) at
Bridges and culvert approaches.
Concreting of 0.2 x 0.2 in the ration (RCC 1:2:4 mix) at station
area where cable laying cannot be achieved for a depth of one
Mtr. (25 running meters of CC = 1Cum
Laying of G.I. Pipes 100mm dia. Medium quality to specification
IS.1239 (part-I) 1990 and galvanised to specification IS.47361986. On bridges, culverts, trench with channel ramps on either
end of the culvery/ bridges. Clamping arrangement with MS
brackets for fixing of GI pipes on bridges/ culverts, small holes
of 5 mm are to be drilled on the pipe before laying of the pipes.
Page 4 of 5
800
MTRS
81.40
65120.00
360
CUM
2022.26
728014.00
1800
MTRS
76.68
138024.00
No SOR No
Description
Qty
Unit
NS
Installation /fixing and wiring of 15U rack and 4 wire way
station equipments/ Selective calling equipment, power supply
unit at new locations in 15U Rack at AEN/PWI/ SI offices /
Residences and LC Gates etc. way station, Selective calling
equipment and power supply unit will be supplied under supply
portion and drawing of cable through PVC conduit Pipe, neatly
lacing the cables, fixing of earth bus bars, extending earth to
various equipment through 16 sq.mm copper cable, fixing of
power distribution panel with 5AC sockets. PVC conduit pipe
and lacing thread shall be supplied by the contractor. All the
materials for installation, commissioning above units shall be
provided by contractor
30
Nos
1739.99
52200.00
5
NS
Final Documentation shall consist of 1). Original documents of
all particulars of Cable laying particulars- cable laying/ testing/
commissioning will be handed over to Executive Engineer-incharge after all the works are over.2). Based on above 12 Nos.
Documentation sets in A4 size shall be prepared covering the
following items broadly-Cable laying particulars- , Block section
measurements, EC/LC gate telephone particulars, Cable route
plan, Tapping diagram, Standard schematic diagram for EC
socket/cable termination, layouts at way station,STM-4,STM-1
circuits etc in programmed CD's-2Nos.
225
KMS
82.58
18581.00
6
NS
Testing and commissioning of the system
20
SECTION
4
TOTAL
GRAND TOTAL
Single Percentage of Rate At par OR Plus OR Minus over the
above items to be quoted by the Bidder .
TOTAL AMOUNT QUOTED BY THE BIDDER
Page 5 of 5
RATE
1740.00
AMOUNT
34800.00
1036739.00
29975382.00