DIMENSIONS
SETTING
The three-step setup procedure adjusts the sensor sensitivity and sets
the LIGHT/DARK mode.
The procedure given below describes a LIGHT mode setting for
proximity fibres and a DARK mode setting for emitter/receiver fibres.
Connecting the REMOTE input to the +Vdc supply is equivalent to
pressing the pushbutton.
The control protection transparent cover can be removed by gently
pulling it while it is completely open.
Fixing holes
O-Ring
(A)
Fibre-optic
Not used
Receiver
Output saturation voltage:
Response time:
Timing function (TIMER):
Indicators:
Fibres insertion
holes
Fibre-optics installation:
Press the lock button and keep it pressed until all the fibres are
completely inserted. Insert the emission fibre in the hole corresponding
to the desired emission (red or green).
The first insertion resistance is due to the O-ring seal; please continue to
insert the fibres for about 6 mm until it touches the photoelectric
components (A).
CONNECTIONS
BLACK
10 … 26.4 Vdc
OUTPUT
GREY
TIMER
WHITE
REMOTE
RED
TEN-3-x 4 WIRE CABLE
BROWN
+
BLACK
10 … 26.4 Vdc
OUTPUT
WHITE
REMOTE
BLUE
0V
ALARM
BLUE
Setting:
Retention data:
Operating temperature:
Storage temperature:
Electric shock protection:
Operating distance
(RED/GREEN emission):
Emission type:
Ambient light rejection:
Vibration:
Shock resistance:
Housing:
Protection class:
Connections:
0V
Weight:
TEN-5-x M8 CONN.
TIMER
OUTPUT
(WHITE)
(BLACK)
2
+ 1
10 … 26.4 Vdc
(BROWN)
4
3-
0V
(BLUE)
TEN-6-x M8 CONN.
REMOTE
(WHITE)
2
+ 1
10 … 26.4 Vdc
(BROWN)
9
25
press the SET pushbutton and keep it pressed until the green LED
flashes. Don’t move the target during this phase.
SET PUSHBUTTON
TEN-2-x
Lock button
Lock button
+
mm
SET LED
12.0
Fix the sensor using the DIN guide or through the fixing holes.
BROWN
2) Output ON state acquisition
Proximity fibres: place the target opposite the sensor at the
maximum distance required;
Emit./Rec. fibres: place the target between the fibre tips;
3) output OFF state acquisition
Proximity fibres: place no target;
Emit./Rec. fibres: place no target;
TECHNICAL DATA
Power supply:
Ripple:
Current consumption
(output current excluded):
Output:
Main output current:
ALARM output current:
INSTALLATION
TEN-2-x 6 WIRE CABLE
25.4
34.25
OUTPUT LED
SET PUSHBUTTON
The pushbutton activates the setup procedure.
DIN guide
25.0
21.75
TIMER LED
SET LED (bi-colour)
During functioning, the green or orange LED ON indicates a normal
operating condition; red blinking indicates an output overload condition.
See the “SETTING” paragraph for setup procedure indications.
Emitter - green LED
(TEN-2/5-x)
Emitter - red LED
press the SET pushbutton and keep it pressed until the SET LED
flashes orange. The flashing rate vares according is are operating
conditions; high flashing rate indicates insufficient received signal
level or excessive distance: improve alignment or reduce the distance
to obtain a low flashing rate. The SET LED flashing is replicated by
the sensor emission and is visible at the fibre tips.
1.5
CONTROLS
OUTPUT LED
The yellow LED indicates that the output status.
place the target opposite the fibre tips at the
maximum distance required;
Emit./Rec. fibres: position the fibre tips on opposite sides;
3.5
12.0
TIMER LED (TEN-2/5-x)
The green led indicates that the timer is ON.
1) Alignment
Proximity fibres:
17
39.5
6.3
26.5
INSTRUCTION MANUAL
44.5
TEN SERIES
8.0
64.0
OUTPUT
TEN-5-x
TEN-3-x
press the SET pushbutton and keep it pressed until the SET LED
lights permanently ON; this means that the procedure has been
completed successfully, and a low contrast (LED ON in orange) or
high contrast (LED ON in green) was detected.
If the SET LED flashes alternately red and green the setup procedure
has failed due to insufficient contrast; repeat the procedure from the
beginning.
TEN-6-x
10 … 26.4 Vdc limit values; reverse polarity protection
2 Vpp max.
60 mA
55 mA
To set the fibre in DARK mode with proximity fibres and in LIGHT mode
with emitter/receiver fibres invert the 2 and 3 steps.
NPN (TEN-x-N) or PNP (TEN-x-P); 30 Vdc max.
100 mA max. (short-circuit protection)
20 mA
without protection
ALARM FUNCTION (TEN-2-x)
-
1 V max. NPN versions / 2V max. PNP versions
100 s
333 s
40 ms minimum output ON
OUTPUT LED (YELLOW)
OUTPUT LED (YELLOW)
TIMER LED (GREEN)
SET LED (RED/GREEN)
SET LED (RED/GREEN)
SET pushbutton
SET pushbutton
SET pushbutton and REMOTE wire
and REMOTE wire
non volatile EEPROM memory
-10 … 55 °C
-25 … 70 °C
Class 2
with (OF-18):
0 … 6 mm (green emission)
0 … 45 mm (red emission)
with (OF-18): 0 … 75 mm (red emission)
with (OF-19):
0 … 25 mm (green emission)
with (OF-19): 0 … 300 mm (red emission)
0 … 180 mm (red emission)
selectable by choosing
RED (630 nm)
GREEN (565 nm) or RED (630 nm)
according to EN 60947-5-2
0.5 mm amplitude, 10 … 55 Hz frequency, for every axis (EN60068-2-6)
11 ms (30 G) 6 shock for every axis (EN60068-2-27)
Polycarbonate
IP65
6 wires 2 m cable
M8 4-pole
6 wires 2 m cable
M8 4-pole
connector
connector
 4.5 mm
 4.5 mm
115 g. max. cable versions / 30 g. max. connector versions
The ALARM output switches ON when the main output is overloaded
and returns OFF when the overloaded is removed.
This output is NPN type for TEN-2-N and PNP type for TEN-2-P,
maximum current 20 mA without short circuit protection.
DECLARATION OF CONFORMITY
We DATALOGIC AUTOMATION declare under our sole responsibility
that these products are conform to the 2004/108/CE and successive
amendments.
WARRANTY
DATALOGIC AUTOMATION warrants its products to be free from
defects.
DATALOGIC AUTOMATION will repair or replace, free of charge, any
product found to be defective during the warranty period of 36 months
from the manufacturing date.
This warranty does not cover damage or liability deriving from the
improper application of DATALOGIC AUTOMATION products.
DATALOGIC AUTOMATION
Via Lavino 265 - 40050 Monte S.Pietro - Bologna – Italy
Tel: +39 051 6765611 - Fax: +39 051 6759324
www.automation.datalogic.com e-mail:info.automation.it@datalogic.com
TIMING FUNCTION (TEN-2/5-x)
DATALOGIC AUTOMATION cares for the environment: 100% recycled paper.
DATALOGIC AUTOMATION reserves the right to make modifications and
improvements without prior notification.
(BLACK)
4
3-
0V
(BLUE)
A delay function TIMER is available which extends the minimum ON output time to 40
ms (see figure aside).
The TIMER enable wire must be connected to +Vdc before powering the sensor to
enable the delay function.
ON
ON
OUT without TIMER
OFF
OFF
ON
ON
OUT with TIMER
40 ms
OFF
40 ms
OFF
Datalogic and the Datalogic logo are registered trademarks of Datalogic
S.p.A. in many countries, including the U.S.A. and the E.U.
826000255 Rev.F
© Copyright Datalogic 2007-2010