Installation Manual Romano Electro Int`l S.A.
advertisement
TECHNICAL FEATURES STAND-BY CURRENT CONSUMPTION ............................................................................................. MAX. 15mA SIREN OUTPUT ............................................................................................................................ MAX. 1A TRUNK RELEASE OUTPUT ....................................................................................................... MAX. 500mA WINDOWS ROLL UP WHEN ARMING, OUTPUT .............................................................................. MAX. 500mA ENGINE KILLER OUTPUT .......................................................................................................... MAX. 500mA DOORS INPUT ................................................................................................................ NEGATIVE TRIGGER 1 TRUNK/HOOD INPUT ........................................................................................................ NEGATIVE TRIGGER 2 CENTRAL DOOR LOCK RELAYS ..................................................................................................... 10A/12V REMOTE CONTROLS ............................................................................................................... HOPPING CODE PROGRAMMABLE PARAMETERS ............................................................................................... 16 PARAMETERS ALARM MEMORY ........................................................................................ ALARM TYPE DISTINCTLY INDICATED DISABLING FAULTY SENSORS ............................................................................... SENSOR DISTINCT INDICATION SYSTEM STATE MEMORIZED WHEN SWITCHING OFF POWER Romano Electro Intl Auto Alarm System S.A. 27-29 Calimachi str., 72266, Bucharest, Tel.:40-1-242.20.20, Fax:40-1-242.20.30, E-mail: sales@roel.ro, www.roel.ro Installation Manual D OC . 50102/16.08.00 / V ERSION 1.0 Alcar® H51 Installation Manual TABLE OF CONTENT CHAPTER I: INTRODUCTION ............................................................................................................. 3 CHAPTER II: THE KIT ..................................................................................................................... 3 CHAPTER III: GENERAL FEATURES .................................................................................................... 4 CHAPTER IV INSTALLATION ............................................................................................................. 5 4.1 SIREN MOUNTING ............................................................................................................................... 5 4.2 PIN SWITCH MOUNTING AT HOOD AND TRUNK ............................................................................................ 5 4.3 CENTRAL UNIT MOUNTING ......................................................................................................... 5 4.4 CONNECTIONS .................................................................................................................................. 5 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 4.4.6 4.4.7 4.4.8 4.4.9 Cable set A ........................................................................................................................................ 5 Cable set B ........................................................................................................................................ 5 Cable set C ....................................................................................................................................... 6 Dconnector ....................................................................................................................................... 8 Econnector ........................................................................................................................................ 8 Fconnector ........................................................................................................................................ 8 G Connector ..................................................................................................................................... 9 H connector ...................................................................................................................................... 9 Pager connecting ............................................................................................................................... 9 CHAPTER V: SYSTEM OPERATING ...................................................................................................... 9 5.1 LEARNING / CLEARING REMOTE CONTROLS .............................................................................................. 9 5.2 SYSTEM PARAMETERS PROGRAMMING ................................................................................................... 10 5.3 SERVICE MODE / EMERGENCY DISARMING .............................................................................................. 14 5.4 ENGINE KILLING ............................................................................................................................... 14 5.5 REMOTE CONTROL OPERATING ............................................................................................................ 14 5.5.1 Arming/disarming with confirmation by siren chirps and flashing lights ....................................... 15 5.5.2 Arming/disarming silent ................................................................................................................... 15 5.5.3 Remote controlled bypassing the sensors .................................................................................... 15 5.5.4 Arming with silent alarm .................................................................................................................. 16 5.5.5 Car finding ....................................................................................................................................... 16 5.5.6 Panic ................................................................................................................................................ 16 5.5.7 Signalling the remote controls number ........................................................................................... 17 5.5.8 Anti-carjacking mode ....................................................................................................................... 17 5.5.9 Trunk release function .................................................................................................................... 18 5.5.10 Two level - Door unlocking, when disarming ................................................................................ 18 5.5.11 Two steps disarming ...................................................................................................................... 18 5.6 ELECTRIC WINDOWS CLOSING WHEN ARMING .......................................................................................... 18 5.7 REVERSE CAR MOVING WARNING ......................................................................................................... 18 5.8 DOOR OPENED WARNING ................................................................................................................... 18 5.9 AUTOARMING .................................................................................................................................. 19 5.10 PASSIVE ARMING/WARNING AT PASSIVE ARMING/TEMPORARY DISABLE OF PASSIVE ARMING ............................. 19 5.11 REMOTE CONTROLLED DOORS LOCK/UNLOCK AND/OR WHEN SWITCHING ON/OFF THE ENGINE ........................ 19 5.12 DUAL MODE ................................................................................................................................. 19 5.13 ALARM MEMORY INDICATION .............................................................................................................. 19 5.14 BYPASSED FAULTED INPUTS INDICATION .............................................................................................. 20 5.15 ANTISCANNING/ANTIGRABBING ......................................................................................................... 20 5.16 NON-VOLATILE MEMORY FOR SYSTEM STATES ....................................................................................... 20 5.17 ALARM SITUATIONS WHEN THE SYSTEM IS ARMED ................................................................................. 20 5.18 COMFORT FUNCTION ...................................................................................................................... 21 5.19 DOOR CONTACTS DELAY, WHEN ARMING .............................................................................................. 21 CHAPTER VI: TESTING/ADJUSTMENTS ............................................................................................. 21 6.1 REAL CONDITIONS TESTING ............................................................................................................... 21 6.1.1 Testing the detection of the burglary attempts .............................................................................. 22 6.1.2 Testing the central door lock commands ........................................................................................ 22 2 23 Alcar® H51 sensors stabilization period) the shock sensor and/or the external supplementary sensor are active. Check the fact that the system warns optical-acoustical by 3 short signals. Check also that the power supply of the bypassed sensorswas disconnected on that specific arming period (sensors LED is off and the alarm system does not respond when the sensor is tested). 6.1.1 Testing the detection of the burglary attempts With the system armed simulate burglary attempts in all the possible ways: 1) Put the key in contact and try starting the engine; the relay contacts should open (the engine should not start), and the system should trigger the alarm (by siren, flashing lights and optionally by pager) for 30s (this is the alarm for engine starting attempt). 2) Open and close one by one all the doors, the hood and the trunk; the system should trigger the alarm (by siren, flashing lights and optionally by pager) for 30s. 3) Open a door and leave it opened; the system should trigger the alarm (by siren, flashing lights and optionally by pager) for 30s, three times subsequently. After that the doors input will be bypassed the other functions of the system remaining active. If the door is closed eventually, the input should become active again. 4) After passing the sensors stabilization period (20s after arming), hit the car slightly; the system should prewarn (for weak shocks). After repeated shocks within 5s, the system should trigger the alarm (by siren, flashing lights and optionally by pager) intermittently 2s ON, 1s OFF, for 15s (repeated shocks alarm). 5) After the stabilization period passed (20s after arming command), hit in astrong manner the car; the system should trigger the alarm (by siren, flashing lights and optionally by pager) intermittently 2s ON, 1s OFF, for 15s (strong shocks alarm). 6) If the system is provided with ultrasonic sensor and the input for the supplementary sensor is programmed properly, then, aftyer the sensors stabilization period (20s after arming), by leaving the window opened, introduce the arm inside, through the window; the system should trigger the alarm (by siren, flashing lights and optionally by pager) for 30s (alarm for violating the interior of the car). 7) If the system is provided with proximity sensor (microwave sensor), and the input for the supplementary sensor is programmed properly, then, after sensors stabilization period (20s after arming), when approaching the car, within sensors range, the system should emit one signal at every detection, according to the value of the parameter 11 (warning for approaching the car). 6.1.2 Testing the central door lock commands Installation Manual CHAPTER I: INTRODUCTION Alcar® H51 is an auto alarm, remote controlled with hopping code. This facility offers a stronger protection than the fixed code systems, since the remote control is changing the code at each button pressing. It is a user-friendly modular system that can be configured in a very complex way. The doors are protected by pin-switches, apart from the trunk and the hood. The alarm assures the engine killing. The command from the shock sensor (included in the basic kit) will pre-warn for weak shocks. For strong shocks or repeated weak shocks the alarm will trigger in a specific way. The ALCAR® H51 range has the following versions: -ALCAR® H51 - ALCAR® H51 minimal kit, -ALCAR H51U - ALCAR® H51 + ultrasonic sensor incorporated; ® -ALCAR H51DL - ALCAR® H51 + central door lock module incorporated; -ALCAR H51P ALCAR® H51 + auto-pager module incorporated; ® ® - - Any combination of the upper options (ex: ALCAR® H51UDLP- maximal configuration, with ultrasonic sensor, with central door lock module and auto-pager module). Supplementary external sensors can be connected, such as one-zone or two-zone microwave sensor or ultrasonic sensor. This way, the system assures the protection of the interior of the car and/or can warn when someone gets close to the car. NOTES: 1) In this manual ALCAR® H51 will be referred as the whole range of auto alarms of this kind, meaning that such functions are optional for the various constructive versions; 2) In this manual the two buttons remote control is referred (button 1) and (button 2). If the remote control has 4 buttons, then the first two only will be used for operating the car alarm. The other two can be used for subsequent developments (ex: for garage doors command, for operating a burglary alarm system etc). CHAPTER II: THE KIT If the car is provided with central door lock check if: a) Doors are locked when arming the system. b) Doors are unlocked when disarming the system (if parameter 6 is active). c) Doors are unlocked when turning off the engine (if parameter 7 is active). d) Doors are locked when turning on the engine (if parameter 8 is active). In the box you will find the following: e) Doors are not locked when the system is passive arming, after 30s after turning off the engine and closing the last door (if parameter 4 passive arming is active). 22 1. Central unit 2. Remote controls (2 pcs.) 3. Pin-switch (2 pcs.) 4. Mounting cables (3 sets) 5. Warning decal (2 pcs) 6. Spare fuses (10A, 2A) 7. Shock sensor + cable 8. Engine killer relay 9. Ultrasonic microphones 10. Valet switch 11. State LED 3 Alcar® H51 CHAPTER III: GENERAL FEATURES 1. Arming/disarming by remote controls (confirmation by siren chirps and flashing) 2. Arming/disarming by remote controls (confirmation by flashing only) 3. Passive arming (programmable) / Warning at passive arming Installation Manual Notes: a) If the system is armed with silent alarm function (no siren), the alarm state will be notified by pager and flashing lights or only by pager, according to the value of parameter 9 (see 5.2., system parameters); 5. Two steps disarming b) Any alarm state can be stopped by pressing shortly (0.5s) the button 1 or 2, without disarming the system. For disarming the system when the alarm is in progress, press button 1 twice (once to stop the alarm and second time to disarm the system). 6. Protection against accidental disarming (auto-arming) 5.18 COMFORT FUNCTION 4. Arming with silent alarm (no siren, programmable) 7. Doors protection 8. Trunk and hood protection, apart from the door input 9. Pre-warning for weak shocks, alarm for strong shocks or repeated weak shocks The Comfort function is available for some newer models of cars. At these cars, when twisting the key the doors will lock. If maintaining the key twisted for more than 5s then the windows will roll up. 10. External sensors connection possibility (microwave, simple or dual and/or ultrasonic) The Comfort function provides when arming a longer trigger (10s) on the lock doors output, no matter of parameter 1 value. 11. Car find Caution! 12. Panic Do not run this wire directly to the door lock actuator, but to the command wires existing on the car! 13. Reverse car moving warning (programmable) For details please call the manufacturer! 14. Warning for door open (programmable) 5.19 DOOR CONTACTS DELAY, WHEN ARMING 15. Warning when approaching the car (optional, programmable) 16. Warning when arming with the lights turned on 17. Engine killing 18. Option for deactivating any sensor by remote control 19. Defective sensors bypassing when arming 20. Separate power supply for each sensor input 21. Low consumption (disconnecting the bypassed sensors power supply) 22. Remote alarm notify (optionally, by pager) 23. Non-volatile memory for system parameters and remote controls 24. System state keeping when disconnecting and reconnecting the power supply This function is only used for the cars which maintain ON the dome lamp, a certain time, after the last door is closed. In this case, the parameter 11 Door contacts delay, when arming will be programmed actively. Then, the state of the door pin switches is only tested after the delay time estabilished by parameter 12. If after delay time, the alarm system detects at least a door opened, it notifies by 3 opto-acoustic signals and bypasses the respective input. If afterwards all the doors will be closed, the respective input becomes actively again. The signal for the door inputs will be taken from the (+) terminal of the dome lamp. CHAPTER VI: TESTING/ADJUSTMENTS 25. Learning/clearing remote controls procedure 6.1 REAL CONDITIONS TESTING 26. System parameters programming procedure 27. Learnt remote controls number notification 1) Stop the engine, close the doors, the hood and the trunk. Arm and disarm the system with and without acoustical confirmation like. The state LEDwill indicate as follows: 28. Anti-car-jacking procedure (programmable) - blinking slow system is armed; 29. Anti-scanning / Anti-grabbing - off system is disarmed; 30. Service mode / Emergency disarming by valet switch - on system is in alarm; 31. Central door lock module incorporated - blinking fast system is within the 30s after disarm command, when it is waiting for a door to be opened (see 5.9). 32. Remote controlled doors lock/unlock and/or when switching ON/OFF the engine (optionally, programmable) 33. Electric windows closing when arming the system (optionally) 34. Trunk release by remote control (optionally) 35. Events Log on the state LED (alarm memory indications) 36. Bypassed defective sensors indicated on the state LED 37. Back-up battery siren (optionally) - system is within 30s after the engine was turned off and the last door was closed and it is counting the time for passive arming (see 5.10). - short blinks after disarming and closing the last door the system indicates the alarm memory or the faulty inputs type; while in programming mode the system indicates the parameters values. 2) Arm the system and bypass manually by remote control the sensors according to 5.5.5. Check the fact that power supply of the bypassed sensor was disabled while armed (sensors LED is off and the alarm system does not respond when the sensor is tested). 3) Arm the system and simulate various situations so, after 20s from arming (at the end of the 4 21 Alcar® H51 Installation Manual 5.14 BYPASSED FAULTED INPUTS INDICATION CHAPTER IV INSTALLATION If when arming the system has bypassed any input (doors, hood, sensors) within 20s after arming, then whn disarming, after opening any door the hood or trunk, the system will indicate by the state LED, the type of input as follows: During this section there are presented the location, the mounting and the electrical connections necessary for the alarm system installation. 1 blink - shock sensor 2 blinks - ultrasonic sensor 3 blinks - contact key (attempt to start the engine) 4 blinks - door contacts 5 blinks - hood, trunk contacts After starting the engine the faulted inputs memory will be reset and the LED will turn off. The alarm memory is prioritary towards the faulty sensors indication. So, the LED will indicate the faulty inputs bypassed only if there was no alarm. 5.15 ANTISCANNING/ANTIGRABBING ALCAR®-51, is protected for scanning and grabbing. 5.16 NON-VOLATILE MEMORY FOR SYSTEM STATES When the system is powered again (after the power was OFF), it enters the state which was previously (armed, disarmed, service, anti-carjacking). If the system was in the arming mode when the power was OFF, then at the power restoring the sensors state and the event memory will be restored and the system will tripp a panic alarm. Note: There is a certain situation namely: if parameter 11 Door contacts delay when arming is enabled, parameter 12 Door contacts delay duration is 5s, a door is opened when arming and the power is breaked before the fifth second from the arming, then when rearming, if the door is still open, the system enters a door alarm . 5.17 ALARM SITUATIONS WHEN THE SYSTEM IS ARMED This alarm system can only be installed on cars that have the negative pole of the battery connected to the chassis! NOTE: Read carefully this manual before starting the installation. If you are not sure you are able to do it by yourself, call a specialist! 4.1 SIREN MOUNTING The siren will be mounted in the hood compartment, away from high temperature sources and humidity. The chosen place should not be obstructed in order not to attenuate the siren sound. Also, the place should be as inaccessible as possible to prevent the tamper. Fasten the siren up side down by using screws. 4.2 PIN SWITCH MOUNTING AT HOOD AND TRUNK Choose the mounting place such as the pin-switches should be able to move about 6mm. in the closed position of the hood and trunk. 4.3 CENTRAL UNIT MOUNTING Choose a horizontal place, hidden, preferably under dashboard. Fasten the central unit with screws on the car chassis. 4.4 CONNECTIONS There are 8 connectors on the central unit (A, B, C, D, E, F, G, H). The connectors correspond respectively to the cable sets A, B, C, D, F, G, H. The connections will be made according to the general mounting diagram (D). 1. When opening a door, the hood or the trunk alarm by siren, flashing lights and optionally by pager, for 30s; 4.4.1 Cable set A If a door is left opened in a burglary attempt, the system triggers the alarm (siren, flashing lights and pager), for three times of 30s each. After the 3 x 30s alarm sequence the doors input is bypassed and the other functions of the system are still active. This is executed even if the alarm is stopped by remote control. The timing for commanding the central door lock system can be set to 0,8s. for electric door lock and 4s. respectively for pneumatic door lock. The selection is made through parameter 1-Timing for door lock. If subsequently the related door is closed, the doors input becomes active again. 2. When trying to start the engine with the key alarm by siren, flashing lights and optionally by pager, for 30s; 3. When the car receives a weak shock optical-acoustical warning for 1s. 4. When the car receives repeated weak shocks within 5s or a strong shock alarm by siren, flashing lights and optionally by pager, for 15s, intermittently 2s ON, 1s OFF; Commands the central door lock system. Before connecting the cable A and setting parameter 1, one should determine the type of central door lock existent on the car. A simple way is to try and lock the car doors by locking the right-front door, by locking this door: 1) the doors are instantly closing, then the car is provided with electric door lock system 2) the doors are closing in an interval of few seconds, then the car is provided with pneumatic door lock system 5. When violating the interior of the car, if the supplementary input is set for ultrasonic sensor alarm by siren, flashing lights and optionally by pager, for 30s; 4.4.2 Cable set B 6. When approaching the car, if the supplementary input is set for proximity sensor programmable warning (see parameter 10). System GND. Connect to (-) pole of the battery. 20 B1 (black) Note: In order to improve the noise immunity it is indicated that the power supply wires (B2-red and B1-black) to be connected directly to the batterys poles. 5 Alcar® H51 Installation Manual B2 (red) General power supply of the system. Check the 2A fuse and connect to (+) pole of the battery together with the pink wire (B5). B3 (purple) Open collector PNP output, maximum 1A (positive trigger). The output state is related to the Parameter 0 value in the following way: Parameter 0 = 1 Parameter 0 = 2 In normal state GND +12V When active +12V GND Generally there are 3 types of siren, which are: 1) Normal siren, which provides two wires (+) and (GND). Parameter 0 should be set as 1 and the siren should be connected as follows: - (+) to B3; - (GND) to GND; 2) Back-up siren, with three wires: (+), (GND) and (COMMAND). On the (COMMAND) wire there should be permanently (+), while the siren is powered ON. Thus, when removing (+) from the (COMMAND) wire, the siren should sound. Parameter 0 should be set as 2 and the siren should be connected as follows: - (+) to (+12V); - (GND) to GND; - (COMMAND) to B3. 3) Back-up siren, with four wires: (+), (GND), (NEG.TRIG) and (POSITIVE TRIG). While the siren is powered ON, it will sound either when (NEG.TRIG) is connected to GND or when (POSITIVE TRIG) is connected to (+12V). On the (COMMAND) wire there should be permanently (+),Thus, when removing (+) from the (COMMAND) wire, the siren will sound. Parameter 0 might be set either 1 or 2 and the siren should be connected as follows: - (+)to (+12V); - (GND) to GND; - (POSITIVE TRIG) to B3 if Param. 0 is 1; - (NEG.TRIG) to B3 if Param. 0 is 2; 5.9 AUTOARMING To assure the protection against accidental disarming of the system, if after disarming command, within 30s there is no door opened or the engine is not turned on, the alarm system will arm automatically. This function is permanently active. 5.10 PASSIVE ARMING/WARNING AT PASSIVE ARMING/TEMPORARY DISABLE OF PASSIVE ARMING If parameter 4 (passive arming- disabled by default) is set enabled, the system will arm passive after 30s from turning off the engine and the last door closed. After closing the last door, the system will notify by an optical-acoustical signal (default) or just optical, for silent disarming. If the parameter 5 is enabled, the passive arming can temporary disable by opening and closing twice a door within 5s. The passive arming is useful since it prevents forgetting the car disarmed. The passive arming is made without locking doors. 5.11 REMOTE CONTROLLED DOORS LOCK/UNLOCK AND/OR WHEN SWITCHING ON/OFF THE ENGINE If the car is provided with central door lock the system will lock the doors when arming and unlock the doors when disarming (according to the value of parameter 6). Also, the system can unlock the doors when turning the engine off (see parameter 7) or lock the doors when turning the engine on (see parameter 8). 5.12 DUAL MODE This referrs to the possibility of triggering the alarm by the ultrasonic sensor only if within 15s are activated at least two sensor types (ultrasonic + proximity or ultrasonic + shock). That means that if parameter 14 (Dual mode) is enabled the alarm triggering by the ultrasonic sensor can only be done if the interior detection was preceded or succeeded within 15s by another sensor triggering (shock or proximity). It is strongly recommended to use dual mode only when the system is provided with all sensors type (shock, ultrasonic and proximity). This mode is useful under these circumstances because it prevents false alarms. Enabling/disabling this mode is made by enabling/disabling parameter 14. It is not recommended to use the dual mode if the system is not provided with proximity sensor. 5.13 ALARM MEMORY INDICATION B4, B6 (gray) Connect to (+) pole of the signaling lamps left and right respectively. If while armed at least an alarm was recorded, after disarming and opening the door, the system will indicate by the state LED the type of the sensor that triggered the alarm, as follows: B5 (pink) 1 blink - shock sensor Power supply for the signaling lamps. Check the 10A fuse and connect to (+) pole of the car battery together with the red wire (B2). 2 blinks - ultrasonic sensor 3 blinks - contact key (attempt to start the engine) 4.4.3 Cable set C 4 blinks - door contacts C1 (orange) open collector, negative trigger, and maximum 500mA load output for window closing when arming the system. The output is active all the time while the system armed. It commands an optional module type RB-06. 5 blinks - hood, trunk contacts 6 After starting the engine the alarm memory will be reset and the LED will turn off. 19 Alcar® H51 Installation Manual b) From this point the system waits 30s, then it returns to the upper state 3, resuming the warning signals. If the button 2 of the remote control is pressed again, with contact key in OFF position only, the system leaves the anti-carjacking mode. It emits 1 acoustic signal for 1s, followed by 2 optical signals and it enters the disarming mode. c) If the button 2 is not pressed and the system reaches the state 4, then the exit procedure should be executed again from point a). C2 (brown) input for checking the engine state ON/OFF. Connect to ON wire (coil) of the contact key switch. In order to find this wire: - Switch the key in contact until the lights in the dashboard turn on; - Search on the contact key hub the wire on which the voltage is +12V; In this position and in START position too, the voltage on this wire should remain +12V. NOTE! Note: After entering the anti-carjacking procedure, if the alarm power supply is disconnected, when the system is powered up again it will enter anti-carjacking state. There is another wire, marked sometimes ACCESSORIES, used to power up some accessories (radio, cooler etc.), which provides +12V with the key in hub and the engine turned on. However, in START position the +12V voltage is not provided anymore. Do not confuse with this one! 5.5.9 Trunk release function C3 (green + white) negative triggered input, for trunk and hood state closed/opened. If an interface module RB-04 is connected, for trunk release, it will be actionated pressing long, for about 2s, button 2 of the remote control. C4 (green) negative triggered input, for doors state closed/opened. The function is active only when the system is disarmed and the engine turned off. For C3 and C4 negative triggered inputs is important the doors switches type! 5.5.10 Two level - Door unlocking, when disarming One can check by using a voltmeter the switching type of the doors switches, this way: For two level door unlocking when disarming the system should be provided with the diode D19 on board. This way, the parameter 6 (unlocking doors when disarming) should be inactivated. 2. Connect the voltmeter between GND and the main contact of the switch. In this configuration the system doesnt unlock the doors when disarming while pressing the button 1. For unlocking the doors by remote the button 2 must be pressed more than 2 seconds. Once this option enabled the trunk release function is not anymore available! 5.5.11 Two steps disarming Any alarm state can be stoped pressing the button 1 or 2 for short time (aprox. 2s) without the system to be disarmed. For system disarming when the alarm is triggered, the button 1 should be pressed twice (once for alarm stoping and seconnd for disarming). 1. Open a door and locate the door switch. 3. If the inside lamp turns on and the voltmeter indicates 0V then the switching is negative. In this case the doors switches will be connected directly to C4, in parallel, according to general mounting diagram (D) 4. If the voltmeter indicates 12V, then the switching is positive. In this case the connection will be made by means of a relay according to diagram C. C When arming the system, if there is connected an optional module RB-06, then the windows will close automatically. Relay for positive trigger doors switches +12V WINDOWS CLOSING WHEN ARMING Lamp 5.6 ELECTRIC Note: Door switch C4/GREEN Input for negative trigger switches 5.7 REVERSE CAR MOVING WARNING 85 When moving backwards the system warns by optical-acoustical signals (or just optical if the system was disarmed silent), according to the setting of parameter 2 (see system parameters programming). This parameter is enabled by default for optical-acoustic notification. 86 Also, when disarming silent, the reverse car warning is optical only. 5.8 DOOR OPENED WARNING If, after the engine is turned on, one of the doors remains opened for more than 15s, the system will warn by 6 optical-acoustical signals, or just optical, according to the value of parameter 3 (see system parameters programming). This parameter is set by default for optical-acoustical warning. If the disarming was silent, the door-opened warning is optically only. If a door is opened while riding, the system wil emit the same warning signals, after 15s. 87 30 Relay NO C5 (purple) Input from (+) pole of the position lights (for warning when arming with the position lights turned on). C6 (white) Input from (+) pole of the backlights (for reverse moving warning function). C7 (yellow) - open collector, negative trigger and maximum 500mA load output for command of the external engine killer relay. In order to use anti-carjacking function, the engine killing will be made on the injection pump, fuel pump, coil etc. Also, the same warning signals will be emitted when the hood or the trunk are opened. 18 7 Alcar® H51 Installation Manual Connect according to diagrams A or B. NOTE! When connecting the relay on starter the four wires will be connected as follows: - Yellow wire of the relay to the yellow wire C7 of the central unit; - Search on the contact key hub the command wire for engine starter (usually a large section one), cut and connect serial with the relay contacts (the blue and the orange wires of the relay); - Red wire of the relay will be connected to C2 (brown) wire of the central unit to ON, on contact key hub; Note: To find the starter command wire on contact key hub: a) Switch the key in contact until the starter is triggered; b) Search on the hub the wire that provides +12V in this position only! In any other position of the key, this wire should provide no voltage. Engine starter killer Engine contact hub C7/YELLOW Engine killer command circuit 5.5.8 Anti-carjacking mode The function is necessary in the case when the burglar threats the owner and takes the car in its presence, with the key in contact. Once the function is triggered, the car will stop after 1min. and will enter the anti-carjacking alarm mode.. ST Starter power up RED YELLOW 85 86 ORANGE RED 87a 30 Engine killer external relay BLUE 85 Engine starter 86 YELLOW ORANGE 87a 30 Engine killer external relay BLUE - Fuel pump - Injection - Induction coil C8 (blue) - open collector, negative trigger and maximum 500mA load output for remote trunk release. This wire will be connect to an optional module RB-04. 4.4.4 Dconnector It is the connector for the state LED. It is recommended to mount the LED in a visible place (usually on the dashboard), in order to notify the existence of the alarm system and to discourage an eventual burglary attempt. 4.4.5 Econnector The shock sensor ES-21K will be mounted on this connector. It is recommended to locate the shock in the center of the car to detect the shocks from any part of the car. The sensor sensitivity is adjustable. The power up of the sensor is cut off when the sensor is bypassed (by remote control or when it if found faulted when arming). 4.4.6 Fconnector An external optional sensor can be connected on this connector (microwave or ultrasonic sensor). This connector is provided with 4 (optionally 5) connection pins: 8 The hopping code remote controls of ALCAR®-H51, are learnt by the central unit through the procedure described in chapter 5.1 Learning/clearing remote controls. The remote controls number, recorded in central units memory (up to 4), can be notified by a simple short press of button 2 while in disarmed mode. The system answers by a number of optical-acoustical signals (or optical only if the system was disarmed silent) equal to the remote controls number. 2) While disarmed, when the engine is turned on, if parameter 13 (anti-car jacking) is enabled, by pressing long (more than 2s.) the button 2 will enter the anti-car jacking mode. O FF Ignition 5.5.7 Signalling the remote controls number 1) While disarmed, when the engine is turned off, pressing long (more than 2s.) the button 2 will activate the trunk release output; C ON AC Ignition Engine contact hub C7/YELLOW O FF C ON AC Engine killer command circuit B The silent alarm function enabling will be confirmed by 2 optical-acoustic signals (or optical signals, depending on arming mode). Note! Engine killing on other devices ST A If the both buttons of the remote are pressed simultaneously during the first 5s after arming, the silent alarm function will be enabled (during respective arming period the siren will be disabled). The function should be enabled when setting the system parameters (see 5.2, parameter 13), and the external 40A/12V relay should be connected to cut the induction coil the injection pump etc. The function doesnt work if the external relay cuts the engine starter! Note! The car owner should have another remote control apart from the keys! To trigger anti-carjacking procedure presslong (about 2s) button 2, when the engine is turned on. The system will enter the procedure and will confirm by flashing lights for 2s. After the confirmation the alarm passes the following states: 1) During first 14s the alarm does not respond to any remote control command; 2) In the following 16s one can leave the anti-carjacking following the exit procedure; 3) In the following 30s the alarm emitts short siren sounds and optical signals, warning that the engine will turn off. One can leave the anti-carjacking following the exit procedure. 4) After expiry of the 60s, the alarm enters the anti-carjacking alarm mode, in which the engine stops, the sirens sounds continuously and the flashing lights are on until the battery is completely discharged. One can leave the anti-carjacking following the exit procedure. To exit anti-carjacking mode you must follow the procedure bellow: a) In any state 2, 3 or 4 previously enumerated press the button 2 of remote control. The warning or the alarm sounds will be stoped. The engine killing will be stoped (if the system was in state 4) and the system will emit 1 optical signal for 2s, followed by 2 optical-acoustic signals. 17 Alcar® H51 Installation Manual by an optical-acoustic or optical signal (depending on arming mode) and advances to the next sensor. 1) GND; If the button 2 of the remote control is pressed, the system doest bypass the sensor, but it advances to the next sensor and confirms by optical-acoustic or optical signal. 2) Warning input (when detecting movement around the car); 3) Alarm input (when detecting movement inside the car); 4) Commanded power up for the optional microwave sensor; 5) Commanded power up for the optional ultrasonic sensor; Sensors bypass is only available for that respective arming period. When disarming the system the bypass is disabled. Example: If one wishes to bypass the shock sensor only it will proceed as follows: 1. During the first 5s after the arming command press button 2 to advance at the shock sensor without bypassing the proximity sensor. The system confirms by an optical-acoustical signal (or just optical if the arming was silent). 2. Press button 1 to bypass the shock sensor. The system confirms by an optical-acoustical signal (or just optical if the arming was silent). 3. Press button 2 for not bypassing the ultrasonic sensor. If the button 2 is pressed the system confirms by an optical-acoustical signal (or just optical if the arming was silent). 5.5.4 Arming with silent alarm If the owner dos not want the theft to be warned, then the system can be armed with silent alarm (the siren is disabled). The using of this function is needed when the system has a pager. The alarm state will be notified on page and flashing lights only, according to the value of parameter 9 (see 5.2. system parameters). The silent alarm function can only be activated within the first 5s after the arming command, by simultaneously pressing both remote control buttons. The function is active during that specific arming period only. The function enabling is confirmed by 2 optical-acoustic signals (or only optical signals for silent arming). When disarming the system, the function is disabled. The connector has 4 pins for standard configuration. Optional, when an internal sensor is mounted besides the built-in sensor, the central unit has to be properly equippated (to assure a separate power supply for ultrasonic sensor / sensors and microwave sensor). These external sensors should provide a negative trigger output when activated. The central unit commands separately the sensors power supplies. They are interrupted when bypassing the sensors (by remote control or when it if found faulted when arming). The external sensors sensitivity is adjustable. NOTE: For all sensors, adjusting the trimmer to the left or to the right the sensitivity decreases or increases respectively. 4.4.7 G Connector This is the connector for the push-button (valet switch). This switch it is used for: - Remote controls learning; - Service mode / emergency disarming; - System parameters programming. NOTE! 5.5.5 Car finding The push-button should be mounted in a hidden place known by the owner only! In order to locate the car in a full parking area, press shortly (0.5s) the button 2. Five optical and acoustical signals will be provided. The signals will be: 4.4.8 H connector - short if no alarm was reported meanwhile; - long if there was an alarm since the system was armed This one connects the ultrasonic sensor microphones. 4.4.9 Pager connecting This function is active with the system armed only. Pager connecting is optional. The related module, by default is not included in the basic kit. NOTE! CHAPTER V: SYSTEM OPERATING The car finding function is not active during the reserved 5s after the arming command. If the button 2 is pressed during the first 5s after arming this command will be interpreteted according to sensors disabling by remote control procedure. 5.5.6 Panic In case of emergency, pressing shortly (0.5s) and simultaneously the two buttons of a remote control can trigger the alarm. The siren will sound continuously, the pager will emit the alarm signal (if there is provided a pager, which is optional) and the flashing lights will flash for three minutes. This function is used to discourage a potential burglar, and to draw the attention towards the vehicle. The function is enabled no matter of the systems state (armed/disarmed), except the first 5s after arming and can be stopped during the thre minutes by pressing shortly any of the buttons. 5.1 LEARNING / CLEARING REMOTE CONTROLS The central unit already knows the two remote controls provided with the basic kit. Up to four remote controls can be learnt by the central unit. In order to learn or clear from memory remote controls, one should do the following: 1) Disarm the system; 2) Switch the engine contact key twice, such as the key switches subsequently between: ON, OFF, ON, OFF; 3) Press the push-button three times within 15s. A success- ful enter in learn/clear mode will be confirmed by two optical and acoustical signals; 4) For learning, press one of the remote controls buttons within 15s. after pressing the push- 16 9 Alcar® H51 Installation Manual button; a successful learning will be confirmed by an optical-acoustical signal; 5) To clear all the remote controls from the central unit memory press simultaneously both remote control buttons of a known remote control. The clearing of all remote controls at once will be confirmed by three optical-acoustical signals; 6) To leave the learn mode switch the contact key to ON position. Also, leaving the learn mode will automatically be made after 15s. in which there is no remote control button pressed. Notes: a) The remote controls record in the central unit memory is made cyclically from location 1 to location 4, respecting FIFO principle (First In First Out). So, if the memory is full, the oldest remote control will be erased when learning a new one. b) By simultaneously pressing bot buttons of a new remote control, while in learning mode, then the system will learn that remote control. (It will not be executed the operation of clearing all the remote controls). c) If the same remote control is learnt twice, it will be confirmed second time too, but it will not fill a second memory location. 1) In the case a remote control was stolen or lost a clearing of all the remote controls at once operation will be effected. Then, the remained remote controls and the new ones will be learnt 2) In the case all remote control were stolen or lost a new remote control learning operation will be effected. Then a clearing of all the remote controls at once operation will be effected followed by a learning operation for the new remote controls. The remote control is also provided with a LED that turns on when pressing any of the buttons. If one note decreasing of the light intensity of the LED then the battery should be replaced. Combining the two buttons it results a lot of functions that will be explained in the followings. 5.5.1 Arming/disarming with confirmation by siren chirps and flashing lights System arming/disarming is simply made by shortly pressing (about 0,5s.) button 1. The system toggles to one state or another according to the current state. The arming confirmation is made both optically and acoustically, by one signal, and the disarming confirmation will be made by two optical-acoustical signals (on flashing lights and siren). When arming: 1) If the system detects the hood, the trunk or a door opened, it warns by three optical-acoustical signals and bypasses the respective inputs during arming. If afterwards the respective inputs are restored (closing the hood, trunk or doors) they become active. After sensors stabilization delay (20s. after arming), by opening again any door, the hood or the trunk the alarm will be triggered. 2) If the system detects the position lights turned on, it will warn by a signal similar to the proximity approach warning, according to the value of parameter 10. When disarming, if the alarm has been triggered while armed, four optical-acoustical signals will be emitted. Note: 5.2 SYSTEM PARAMETERS PROGRAMMING 1) Table I: SYSTEM PARAMETERS (default values in bold) No. the remote controls is about 30m. The remote control is provided to 2 buttons, which will be referred as 1 and 2. After arming the first 5s. are reserved for supplemental commands such as: 2) manual sensors bypass by remote control (the proximity sensor, the shock sensor and the ultrasonic sensor); O p tic al-ac o u s tic al s ig n al P ara m e ter d es c rip tio n 1 sig n a l 2 sig n a ls 0 S ire n typ e P o sitiv e trig g e red Neg ative trigg ere d 1 C e ntra l d o or lo ck tim ing 0 ,8 s (e le ctrica l) 4 s (pneum atically) 2 Reverse ca r m oving warning o p tica l-ac o u stic al O p tica l o nly 3 Wa rning fo r do or o pe n o p tica l-ac o u stic al O p tica l o nly 4 P assive arm ing e nab le d d is ab led 5 Te m po rarily disa bling the pa ssive a rm ing e n a b le d d is ab le d 6 Unlock the do ors when d isa rm ing e n a b le d d is ab le d 7 Unlock the do ors when turning O F F the e ngine e nab le d d is ab led 8 L ock the d oo rs whe n turning O N the e ngine e nab le d d is ab led 3) silent alarm enabling (the siren is disabled); 4) System disarming can only be made after the 5s after arming command; 5) If the parameter 11 - Door contacts delay when arming is enabled, then the doors pinswitches are tested only after delay duration estabilished by parameter 12. If, the delay duration is over and the system detects at least one opened door, it will warn by three optical-acoustical signals and it will bypass the respective input during arming. 6) If afterwards all the doors are closed, the respective input becomes active again, after sensors stabilization delay (20s after arming). 5.5.2 Arming/disarming silent When no acoustical confirmation is needed, press the button 1 for about 2s instead of the short press described before (0.5s). All the signals will become silent, meaning that the optical confirmation only will remain active for respective arming/disarming period (warning for reverse car moving, for door open, for arming with position lights turned ON, for silent siren, for sensors bypassing by remote control, for doors, hood and trunck bypassing, for faulted sensors disabling when arming). 5.5.3 Remote controlled bypassing the sensors Remote controlled bypassing the sensors can only be made during the first 5s after the arming command. The bypass order is: proximity sensor -> shock sensor -> ultrasonic sensor. If the button 1 of the remote control is pressed, the system bypasses respective sensor, confirms 10 15 Alcar® H51 Installation Manual The LED will blink once or twice according to the current value of the parameter 5. To set the parameter 5 resume from step 6; No. 8) To leave the programming mode switch the contact key to OFF position. 1 signal Notes: If during the parameters programming procedure the push-button is not pressed for 15s. the LED will turn OFF and the system will wait for the contact key to be switched to OFF position, without responding to any command. After programming parameter 15 (the last), if the push-button is pressed the LED will turn OFF, the system will respond by an optical-acoustical signal and will wait for the contact key to be switched to OFF position, in order to leave the programming mode. If the contact key is not switched to OFF position the system is not responding to any command. The system parameters settings are recorded into the non-volatile memory. 5.3 SERVICE MODE / EMERGENCY DISARMING Within certain situations (such as leaving the car to a car-service) it is recommended to disable the alarm system. In this cases the system should be switched to service mode: 1) Disarm the system; 2) Press the push-button 3 times within 15s. A successful enter to service mode will be confirmed by three short optical-acoustical signals; 4) Now the contact key can be taken off and the system will remain in service mode. The central unit keeps this state (even when the power is removed) and does not respond to the remote controls buttons press. To leave the service mode, repeat the upper steps 2, 3 and 4. After taking off the contact key, the alarm is functional. 2 signals 9 Silent alarm (no siren triggering) Pager warning only pager and lights 10 Proximity approach warning 3 short chirps 0,5s sound signal 11 Door contact delay when arming enabled disabled 12 Door contact delay duration 20s 5s 13 Anti-carjacking enabled disabled 14 Dual mode enabled disabled 15 Comfort enabled disabled The parameters programming procedure: 1) Disarm the system; 2) Switch the contact key to ON position; 3) Optical-acoustical signal Parameter description Switch the engine contact key ON then OFF; 3) Press three times the push-button within 15s. There will be a short optical-acoustical confirmation; 4) Switch the engine contact key ON. A successful enter in the programming mode will be confirmed by a new short optical-acoustical confirmation. The LED will blink once or twice, according to zero parameter value; Note: To program zero parameter, go directly to step 6) and for the other ones resume the step 5). 5) For choosing the parameter to be set press shortly (less than Emergency disarming is necessary in the limit situation when both remote controls have been lost and the alarm system should be disarmed. Repeat the upper steps 2, 3 and 4. When opening the door the system will trigger the siren until reaching the step 3. After step 4 the system enters the service mode. The system disarming is only made after leaving the service mode, when new remote controls could be learnt. 1s.) the push-button of a certain number of times, equal to the parameter number, according to the previous table within 15s. Every push-button pressing (passing from a parameter to another) will be confirmed by a new optical-acoustical signal. 5.4 ENGINE 6) KILLING After choosing the parameter the LED will blink once or twice, according to the parameter value; To set the parameter as needed, within 15s. press and keep pressed the The engine killing while the system is armed is made by a 40A/12V NC relay, which will be connected to cut the ignition, the fuel pump, the injection etc. The relay is active when the system is armed and the contact key is twisted into the engine start contact hub. push-button. The parameter toggles subsequently from a state to another. Meanwhile the system confirms alternatively by one or two optical-acoustical signals. Release the push-button when having the confirmation of one of the two values needed, as indicated by the table. After releasing the push-button the LED will blink once or twice according to the chosen value. When anti-carjacking function is enabled, this relay is used to lock other accessories (induction coil, injection pump etc). 7) For passing to another parameter press shortly the push- 5.5 REMOTE CONTROL OPERATING button of a number of times that gives the difference between the order number of the two parameters. Most of the alarm system functions are operated by means of the two remote controls. The range of Example: After setting parameter 2, for passing to parameter 5, press the push-button three times. 14 11 Alcar® H51 Installation Manual D ® Alcar H51 Main Unit VALET BUTTON A6 A5 A4 A3 A2 A1 B6 B5 B4 B3 B2 B1 C8 C7 C6 C5 C4 C3 C2 C1 Adjusting trimmer for the built-in ultrasonic sensor A B C D E F5/GREEN F5 F4 F3 F2 F1 H4 H3 H2 H1 SENZOR MICROUNDE F G H Transmitter-Receiver for built-in ultrasonic sensor Pager To Central Door Lock System Warning for movement detection around the car B5/PINK Alarming for movement detection inside the car 10A F3/BLACK F2/RED GND STATE LED Power for Perimeter Sensor 2A F1 CONNECTOR E C4/GREEN Door Contacts DOORS (Diagram C) HOOD B4/GREY Right Flasher (+) B3/PURPLE C3/GREEN+WHITE NC Siren Circuit (1A) C A1/BLUE+WHITE Locking/Unlocking can be made from the driver's door and from the passenger door as well. Also, sometime there are some switches built inside the car, which allow Central Door Lock System activating. In this case the connecting will be done in the same way such as in the previous sketch. OBS: Daewoo Espero car is provided with an actuator in the drivers door and the control wires for locking-unlocking are as follows: GND on brown wire with white line - unlock the doors GND on black wire with green line - lock the doors Lock Relay NO 12V A6/YELLOW NO A5/YELLOW+WHITE NC GND NC C C GND A4/GREEN A3/GREEN+WHITE A2/BLUE Actuator Blue A1/BLUE+WHITE Red Unlock Relay If necessarily, the actuator will be connected together with the control lever. OBS: For Daewoo Cielo cars the connections are as follows (left are the actuator wires, right are the main unit connections and respectively to the door wires): Actuator Main Unit red blue+white blue blue Existing Door Electrical contact black black brown brown+white purple brown+red If the car is equipped with electric central door locking with an actuator in the driver's door and where the central door locking is controlled only through an existing switch installed in the passenger compartment Lock Relay NO A6/YELLOW 12V NO A5/YELLOW+WHITE (Diagram C) NC C6/WHITE Positive terminal (+) of the reverse car lights A4/GREEN NC A3/GREEN+WHITE C A2/BLUE C A1/BLUE+WHITE C8/BLUE Trunk Openeing Control C2/BROWN Accessories Unlock Relay ATTENTION! The Central Door Lock of these cars is not working when opening the door using the key. In this case the connections will be done according to the previous sketch. If the car is equipped with electro - pneumatic central door locking with an actuator in the driver's door A CC O TF SF O Lock Relay N C5/PURPLE Positin Lights NO A6/YELLOW GND (12V) NO A5/YELLOW+WHITE 12V (GND) NC A c tua tor sw itc h (ins id e the door) A4/GREEN NC A3/GREEN+WHITE C7/YELLOW See A and B Diagrams C A2/BLUE Engine Killing 12 (not connected) C A2/BLUE Hood and Trunk Contacts TRUNK A4/GREEN NC A3/GREEN+WHITE System Power Left Flasher (+) GND NO A5/YELLOW+WHITE B2/RED B6/GREY Shock Sensor Input NO A6/YELLOW If the car is equipped with electric central door locking without an actuator in the driver's door Power for Light Flashers B1/BLACK GND Power for Ultrasonic Sensor Lock Relay Unlock Relay GND F4/BLUE SENZOR ULTRASUNETE GENERAL MOUNTING DIAGRAM If the car is equipped with electric central door locking with an actuator in the driver's door C1/ORANGE Window roll-up control Unlock Relay C A1/BLUE+WHITE A ir C om p re ss or 13