COOPER LIGHTING - SURE-LITES ®
DESCRIPTION
The All Pro Series is the most economical LED combo (including LED
emergency light heads) for general purpose applications. The durable,
injection molded, thermoplastic material resists discoloration due to UV
radiation and the energy efficient, low maintenance LED’s provide bright
illumination. All AP series combos offer universal configurations (single
and double face) and have universal mounting capability (ceiling, wall,
end).
Type
Catalog #
Project
Date
Comments
Prepared by
S P E C I F I C AT I O N F E AT U R E S
E l e c t ri c a l
- Dual Voltage Input 120/277
VAC, 60Hz
- Line-latching
- Solid-State Voltage Limited
Charger
- Solid-State Switching
- Brownout Protection
- Low Voltage Disconnect
- Overload/Short Circuit
Protection
- Test Switch / Power Indicator
Light
- High Power Combo available
capable of running two additional
LED remote heads
- 3.6V, .78W DC Long Lasting
LED Heads
H o u s i n g C o n s t ru c t i o n
- All components are injection
molded, color stable, high
impact thermoplastic material
- Designer white textured finish
standard
- Components are of snap-fit
construction to facilitate
under 5-minute installation
- Reinforcing ribs throughout
to provide maximum strength
- Molded-in wireways facilitate
internal wire routing and
connections
- All components including
battery and electronics are
located inside the exit
housing
- Snap-out or snap-in chevron
directional indicators have
full 3/4” stroke
- Universal exits can be field
configured as single face or
double face
- Snap-fit canopy with captive
mounting screws included
with all exits
- Exit can be ceiling, wall, or
end mounted
- Universal J-box mounting
pattern
- Operating temperature range
10C to 40C
B a tte r y
- Sealed Nickel Cadmium
- Maintenance Free, Long Life
- Standard Recharge Time:
24 hrs (max.)
Code Compliance
- UL 924 Listed
- UL Damp Location Listed
- Life Safety NFPA 101
- NEC/OSHA
- Most State and Local Codes
L a m p Da t a
- AC LED: Long life LED lamps
provide uniform diffused
illumination
- DC: LED DC lamps (Brighter in
emergency mode)
- Heads DC: 3.6V, .78W Long Life
LED Heads Light Output
Equivalent to 5.4W Incandescent
APC / APCH
SERIES
EXITS WITH
LED HEADS
COMBO
Wa rra n t y
- Exit – 1 year
- Battery:15-Year pro-rata
(Nickel Cadmium)
T H E R M O P L AST I C
S E L F P OW E R E D
EXIT / EMERGENCY WITH
DOUBLE HEADS
LED LAMPS
TM
ENERGY
D ATA
Combo High Power
Standby Mode
LED Exits - Red
(Fully charged
Input Power:
Battery):
120V = 2.34W
Sealed Nickel
277V = 1.62W
Cadmium Battery
Input Current (Max.):
120V = .14A
3-15/16”
[100mm]
5-1/2” [140mm]
3/4”
[19mm]
Combo LED Exits -
277V - .10A
Red
Power Factor:
Input Power:
120V = >.14
120V = 1.31W
277V = >.06
277V = 1.68W
7-1/2”
[191mm]
Input Current (Max.):
Combo High Power
120V = .09A
LED Exits - Green
277V - .09A
Input Power:
Power Factor:
120V = 2.8W
120V = >.12
277V = 2.1W
277V = >.07
Input Current (Max.):
120V = .10A
8-1/4”
[210mm]
Combo LED Exits -
277V = .10A
Green
Power Factor:
Input Power:
120V = >.20
120V = 1.55W
277V = >.07
277V = 1.45W
11-11/16” [297mm]
1-3/4”
[45mm]
16-9/16” [421mm]
2-5/16”
[59mm]
Input Current (Max.):
Charge Mode
120V = .09A
(Discharged
277V = .09A
Battery):
Power Factor:
Sealed Nickel
120V = >.14
Cadmium Battery
277V = >.06
Input Power
consumption is
increased to 4.2 watts
in the charge
operating mode for
red units and 5.0
watts for green units.
Specifications and dimensions subject to change without notice.
Consult your representative for additional options and finishes.
ADX110025 pc
2011-02-02 11:08:01
APC / APCH SERIES EXITS WITH LED HEADS COMBO
O R D E R I N G I N F O R M AT I O N
SAMPLE NUMBER: APC7R
Family
APC7 = Self-Powered with LED All Pro Exit/Emergency with LED Heads
APCH7 = Self-Powered with LED All Pro Exit/Emergency with LED Heads,
High Power with remote capability
Face Options
__ = Universal
Letter Colors
R = Red
G = Green
T E C H N I C A L DATA
Lamps
The AP Series Exits with Heads use energy
efficient, long life LED’s to provide uniform
diffuse illumination of the exit face. The low
operating costs and zero maintenance
requirement makes LED lamps the wisest choice
for exit signs today. Emergency exit illumination
is provided by LED lamps and the heads employ
3.6V, .78W DC Long Lasting LED Heads.
H o u s i n g C o n s t ru c t i o n
Rugged, durable, injection molded
thermoplastic materials are used throughout the
AP Series Exits with Heads. All structural
components are designed with reinforcing ribs
to add additional rigidity and to maximize
structural integrity. These materials are impact
and scratch resistant, and they have been UV
stabilized to resist discoloration due to age and
ultraviolet radiation. All components are
designed to be of snap-fit construction - no
mechanical fasteners - to facilitate installation in
under 5-minutes. Any components required for
installation (wirenuts, wire leads, universal
metal J-box bracket, etc.) are all included with
each exit. The universal design of the AP Series
Exits with Heads enables universal exits to be
configured as single face or double face in the
field. The AP Series Exits with Heads can be
wall, ceiling, or end mounted; a rugged, snap-fit,
low profile canopy with captive screws is
included with every exit for ceiling and end
mounting applications.
Lens
Lenses for the AP Series Exits with Heads are
made from durable impact resistant
thermoplastic. All exit faces are designed with
full 3/4” stroke snap-out or snap-in chevron
directional indicators to insure maximum
visibility and compliance with the latest codes.
L i n e - L a t ch e d
All Pro’s line-latched electronic circuitry makes
installation easy and economical. A labor
efficient AC activated load switch prevents the
lamps from turning on during installation to a
non-energized AC circuit. Line-latching
eliminates the need for a contractor’s return to a
job site to connect the batteries when the
building’s main power is turned on.
Te s t Sw i t ch / Powe r I n d i c a to r L i g h t
A test switch located on the bottom of the exit
permits the activation of the emergency circuit
for a complete operational systems check. The
Power Indicator Light provides visual assurance
that the AC power is on.
S o l i d - S t a te C h a rge r
Supplied with a 120/277 VAC, voltage regulated
solid-state charger. Immediately upon
restoration of AC current after a power failure,
the charger provides a high charge rate. The
charge circuit reacts to the condition of the
battery and regulates the charging process in
order to maintain peak battery capacity and
maximize battery life. Solid-state construction
recharges the battery following a power failure
in accordance with UL 924.
O ve rl o a d a n d S h o rt C i rc u i t
P ro te c t i o n
B row n o u t C i rc u i t
S e a l e d N i cke l C a d m i u m B a tte r y
The brownout circuit on All Pro’s exits monitors
the flow of AC current to the exit and activates
the emergency lighting system when a
predetermined reduction of AC power occurs.
This dip in voltage will cause most ballasted
fixtures to extinguish causing loss of normal
lighting even though a total power failure has
not occurred.
All Pro Emergency sealed nickel cadmium
batteries are maintenance-free with a life
expectancy of 15 years. The sealed rechargable
nickel cadmium battery offers high discharge
rates and stable performance over a wide range
of temperatures. The specially designed
resealable vent automatically controls cell
pressure, assuring safety and reliability. This
battery is best suited for harsh ambient
temperatures because the electrolyte is not
active in the electrochemical process.
S o l i d - S t a te Tra n s fe r
The AP Series Exits with Heads incorporates
solid-state switching which eliminates corroded
and pitted contacts or mechanical failures
associated with relays. The switching circuit is
designed to detect a loss of AC voltage and
automatically energizes the lamps using DC
power. Upon restoration of AC power, the DC
power will be disconnected and the charger will
automatically recharge the battery.
The solid-state overload monitoring device in
the DC circuit disconnects the lamp load from
the battery should excessive wattage demands
be made and automatically resets when the
overload or short circuit is removed. This
overload current protective feature eliminates
the need for fuses or circuit breakers for the DC
load.
Wa rra n t y
All Pro products are backed by a firm one year
warranty against defects in material and
workmanship. Maintenance free, long life,
sealed nickel cadmium batteries carry a fifteenyear pro-rata warranty.
L ow Vo l t a ge D i s c o n n e c t
When the battery’s terminal voltage falls, the
low voltage circuitry disconnects the lighting
load. The disconnect remains in effect until
normal utility power is restored, preventing
deep battery discharge.
Specifications and dimensions subject to change without notice.
Sure-Lites • Customer First Center • 1121 Highway 74 South • Peachtree City, GA 30269 • TEL 770.486.4800 • FAX 770.486.4801
ADX110025 pc
2011-02-02 11:08:01