RX16FT-IS
Flush Mount Lift Rack
SPECIFICATIONS
Site Specifications
Substructure Requirements
Refer to 6367-T for full details
Power Requirements
208-230 VAC, single phase power, 26 Amp
Air Supply Requirements
90-150 PSI (6.2-10.3 bar)
Jacks require 125 PSI (8.6 bar) for full capacity
Minimum Concrete Spec.
3 in. (76 mm) thick, 3000 PSI (20,700kPA) rating
Maximum Floor Slope
2 in. (51 mm) over 126 in. (3200 mm)
Product Specifications
Max. Vehicle Weight
16,000 lbs. (7257 kg)
Max. Wheelbase
RX16FT-IS Shown
General Service
187 in. (4750 mm)
Two-Wheel Alignment
182 in. (4623 mm)
Four-Wheel Alignment
158 in. (4013 mm)
Alignment Height
All lock positions
Min. Four-Wheel Alignment
88 in. (2235 mm)
Lifting Speed
1 speed 60 seconds
Lowering Speed
2 speed, 25 seconds
MODEL FEATURES / DIMENSIONS
FT-IS
Features
Dimension
9000-lb Swing Air
Jacks (2)
92.5 in.
Outside Width (W1)
Two-Speed
Lowering
2350 mm
40 in.
Inside Width (W2)
1016 mm
231.375 in.
Length (L)
5877 mm
26 in.
Runway Width (R)
660 mm
Raised Height (H1)
1829 mm
72 in.
14.75 to 15.25 in.
Depth (H2)
W2
375 to 387 mm
R
H1
H2
W1
L
Continued on Page 2
For lift rack information visit:
www.hunter.com/lift-racks
For general inquiries visit:
www.hunter.com
or call
800-448-6848
For local contact visit:
www.hunter.com/contact-hunter
Form 6492-T, 06-15
Supersedes Form 6492-T, 08-13a
Copyright © 2015, Hunter Engineering Company
RX16FT-IS
Flush Mount Lift Rack
SPECIFICATIONS (Refer to 6367-T for substructure construction requirements)
!
96 1/2"
(2451 mm)
WARNING
STAY BEHIND
YELLOW LINE
WHEN THE
LIFT MOVES.
HAWKEYE SERIES SENSORS
AND PRONTO SYSTEMS HAVE
SPACE REQUIREMENTS IN
FRONT OF LIFT THAT MUST BE
MET, REFER TO APPROPRIATE
SITE REQUIREMENTS.
OPTIONAL 1 1/2 IN. DIA. CONDUIT
FOR COMMUNICATION CABLE
TO ALIGNMENT CONSOLE
128-978-2
DECAL 128-978-2
(4 places on edging and 2 places on lift)
!
WARNING
OPT. FRONT STEP
(12" (305 mm)
MAX. DEPTH)
34 3/4"
(883 mm)
64"
(1626 mm)
41 3/8"
(1051 mm)
EXTENDER
PLATES
51-2464-1-PPP
AND
RAMPS
147-141-1-PPP
FILLER
PLATE
51-2308-1
(4 places)
(placed over
14" X 5"
cutout)
14"
(356 mm)
PIT DEPTH OF
14 3/4" to 15 1/4"
(375 mm to 387 mm)
REQUIRED AT
FRONT END OF PIT
OPTIONAL CONSOLE
LOCATION
5"
(127 mm)
SLOPE
PIT
FLOOR
TOWARD
DRAIN
(1/2 )
ANGLE AROUND PIT
PERIMETER:
- not around 14" X 5" cutouts
- painted safety yellow
- not supplied by Hunter
G N I N R AW
!
G N I N R AW
!
141 3/4"
(3600 mm)
APPROX. 2" (51 mm) TYPICAL
45
6" MIN.
RADIUS
DRAIN
LOCATED
IN
CENTER
OF PIT
CONDUIT
EXIT FLUSH
WITH
PIT FLOOR
ROUTE 4" MIN DIAMETER
CONDUIT OR EQUIVALENT
CLOSED CHANNEL FROM
PIT FLOOR TO BASE OF
CONSOLE
14" X 5"
CUTOUT
(4 places)
231 3/8"
(5877 mm)
14"
(356 mm)
ENTIRE PIT
(BOTTOM AND WALLS)
MUST BE HARD
TROWEL FINISH
5"
(127 mm)
CONSOLE CONDUIT DETAIL
22"
(559 mm)
VEHICLE APPROACH
16"
(406
mm)
RAMPS
147-141-1-PPP
33 3/4
(857 mm)
OPTIONAL REAR STEP
(6" (152 mm) MAX. HT.)
G N I N R AW
32"
(813 mm)
BAY DOOR
**
15" TO 41"
(381 TO 1041 mm)
!
** SITES WITH D.R.W. TRUCK
TRAFFIC SHOULD USE 20" MIN.
CONSOLE TO PIT DISTANCE.
6" MIN.*
(152 mm)
BAY DOOR
* LONGER VEHICLES WILL NEED TO BE SERVICED WITH BAY DOOR OPEN. TO
ACCOMMODATE MOST VEHICLES, INCREASE SPACE BEHIND PIT TO 39" (991 mm) OR
GREATER.
*Non-standard positioning of control console is limited to a maximum space between console and rack of 6 feet
(1829 mm) at the approach ramp end and 17 feet (5182 mm) at the turnplate end. Additional threshold and perhaps
hydraulic hoses will be required (refer to Installation Instruction for details)..
All dimensions shown are for finished pit. Accomodate tile thickness as needed.
Form 6492-T, 06-15
Supersedes Form 6492-T, 08-13a
Copyright © 2015, Hunter Engineering Company