STEP # 1
STEP # 2
Pieces needed for this step:
Pieces needed for this step:
Part # 1
Part # 1
Part # 7
2 Count
Part # 6
2 Count
2 Count
Left Side Support
Right Side Support
38" Base Support Pole
1 1/4" Phillips Head Screws
1) Insert one 1 1/4" phillips head screw
through the hole located at the front and
base of the left side support (#1).
2) Align the 38" base support pole with
the 1 1/4" phillips head screw and secure.
3) Insert one 1 1/4" phillips head screw
through the hole located at the front and
base of the right side support (#1).
37 3/4" X 15" Organizer Base
1 1/4" Phillips Head Screws
Standard Bolts
1) Pick up organizer base (#6) by the front
and the back. Place curved piece over
organizer base pole (#7).
2) Gently push down at the front of the
organizer base (#6) to ensure that the
organizer base (#6) rests on the organizer
support pole (#7).
3) Pull both the left and right side support
pieces (#1) forward and place them on the
floor. See picture # 2
4) Align the 38" base support pole with
the 1 1/4" phillips head screw and secure.
4) Lift up the back of the organizer base
(#6) so that it is at a 90% angle to the floor.
5) Align holes of base support (#6) and
left and right side supports and secure with
1 1/4" phillips head screws and standard
bolts.
STEP # 3
STEP # 4
Pieces needed for this step:
Pieces needed for this step:
Part # 14
Part # 11
4 Count
Part # 4
Part # 4
2 Count
2 Count
29.5" X 13.5" Left Shelf Support
29.5" X 13.5" Right Shelf Support
1/2" Phillips Head Screws
1) Pick up left shelf support (#14) and lean
against left side support (#1) as pictured
above.
2) Align Side Support (#14) with the holes
located at the left side of the organizer
base (#6).
3) Insert 1/2" phillips head screws through
the bottom of the the organizer base (#6)
and secure to the left shelf support (#14)
12" Lower Bag Support Pole
12" Lower Bag Support Pole
1 1/4" Phillips Head Screws
1/2" Phillips Head Screws
1) Raise organizer so that it now stands in
its upright position (as pictured above).
2) Align lower bag support pole (#4) with
left side support (#1).
3) Insert 1 1/4" phillips head screw through
the exterior of the left side support (#1) and
secure to the lower bag support pole (#4)
4) Insert 1/2" phillips head screw through
the interior of the left shelf support (#14)
and secure to the lower bag support pole
(#4).
5) Repeat steps 2 - 4 for the right side.
4) Repeat steps 1 - 3 for right shelf support.
STEP # 5
STEP # 6
Pieces needed for this step:
Pieces needed for this step:
Part # 10
Part # 9
Part # 8
29.5" X 12" Back Shelf Support
1) Slide back shelf support (#10) into the
slots located at the back of the left side
support (#11) and right side support (#14)
2) Lower back shelf support (#10) all the
way to the organizer base (#6).
Note: The top of the back shelf support
(#10) has a hole at the top right hand side.
14" X 13.5" Top Shelf
4 count Plastic Corner Protector
1) Place corner protectors (#8) on each
corner of top shelf (#9)
STEP # 7
STEP # 8
Pieces needed for this step:
Pieces needed for this step:
Part # 15
Part # 5
Part # 9
4 Count
Part # 3
Part # 3
2 Count
2 Count
Plastic Washer
Door
Top Shelf
1/2" Phillips Head Screws
1) Place plastic washer (#15) over the hole
located on the organizer base (#6) just to
the left of the right shelf support (#11)
2) Insert the door (#5) hinge pin through the
plastic washer (#15) and into the organizer
base (#6).
3) Align the hole on the top shelf (#9)
which is located to the left of one of the
corner protectors (#8) over the door (#5)
hinge pin. See the photo below.
12" X .75" Top Support Pole
12" X .75" Top Support Pole
1 1/4" Phillips Head Screws
1/2" Phillips Head Screws
1) Align top support pole (#3) with the hole
on the left side support (#1) which is
located at the back of the left side support
(#1) near the top.
2) Insert one 1 1/4" phillips head screw
through the exterior of the left side support
(#1) and secure to the top support pole (#3)
3) Insert one 1/2" phillips head screw
through the hole located at the back left
of the top shelf (#9) and secure to the top
support pole (#3).
4) Please make sure that the hole in the
middle of the top support pole is parallel
with the floor.
5) Repeat steps 1 - 4 for the right side.
4) Secure the top shelf (#9) to the right front
shelf support (#11) using one 1/2" phillips
head screw.
5) Secure the remaining corners of the
top shelf with 1/2" phillips head screws.
STEP # 9
STEP # 10
Pieces needed for this step:
Pieces need for this step:
Part # 2
Part # 2
4 Count
2 Count
6 Count
Part # 13
U Shaped Upper Bag Support
U Shaped Upper Bag Support
1 5/8" Phillips Head Screws
1" Phillips Head Screws
Cap Bolts
1) Align the hole at the back of the U
shaped upper bag support (#2) with the
center hole of the left top support pole (#3)
2) Insert one 1 5/8" screw through the U
shaped upper bag support (#2) and through
the left top support pole (#3). Secure with
a cap bolt at the back of the left top
support pole (#3).
3) Insert one 1 5/8" phillips head screw
through the left side of the U shaped
upper bag support (#2) and through the left
side support (#1). Secure with a cap bolt.
4) Insert one 1" phillips head screw through
the right side of the U shaped upper bag
support (#2) and through the top shelf (#9) .
Secure with a cap bolt.
5) Repeat steps 1 - 4 for the right side.
Nylon Clips for hanging shelves
1) Place nylon clips (#13) at desired
locations on interior of right shelf support
(#1) and left shelf support (#14). Make sure
that nylon clips are at the height to ensure
that the shelf will rest properly.
STEP # 11
Pieces needed for this step:
Part # 12
Part # 12
13" X 12" Middle Shelf
13" X 12" Middle Shelf
1) Angle the first shelf (#12) into the locker
with the left edge of the shelf being lowered
onto the bottom nylon clips (#13).
2) Lower the right side of the shelf (#12)
so that it rests on the top of the nylon clips
(#13) on the right side.
3) Press down on the right side of the shelf
(#12) so that the shelf rests on the clips
and is secured. It may be necessary to
push the top of the nylon clip in order for the
shelf to rest securely.
4) Repeat steps 1 - 3 for the top shelf.
STEP # 12
Place black felt on top shelf
Congratulations, your steel organizer is complete!