CAT:
COVELUMTM
FEET:
DESIGNER & STANDARD SERIES
Architectural design quality LED modules
for use with Covelum™, create high CRI
illumination for indirect applications.
PROJECT:
TYPE:
FEATURES
• Critical white color applications within +/-50°K, recommended
for indirect illumination of coves or niches with colored or white
backgrounds up to 5 feet high (Designer Model) or backgrounds up
to 3 feet high (Standard Model)
• Flexible field cuttable dual wire system bends 90° easily to fit
concave and convex curves without special hardware
• Festoon Sockets permit easy replacement of LED Modules.
• Designer Model Series LED Modules create high CRI illumination at
over 400 Lumens per foot
Standard Model Series LED modules create specific color
illumination approximately 200 Lumens per foot - See chart below
• Low maintenance, energy efficient lighting for high or low ambient
light interior applications
• Smooth full range dimming capability with commercially available LV
(magnetic) dimmers, ELV or 0V-10V dimming (see pg 5 for dimming)
Covelum™ LED with
2.5" O.C. Designer
Model Series Modules
SPECIFICATIONS
2.5" OC Standard Model Series Modules
EFFICACY
LM/WT
CRI
LM/FT
Delux Warm White (2200°K) at 2.5” O.C.
64.23
85.2
345.60
6.72
5.38
1.12
Delux Warm White (2400°K) at 2.5” O.C.
67.64
85.7
363.90
75.82
5.38
1.12
Delux Warm White (2700°K) at 2.5” O.C.
71.50
84.6
384.70
80.15
5.38
1.12
Warm White (3000°K) at 2.5" O.C.
75.46
83.5
406.00
81.20
5.38
1.12
Neutral White (3500°K) at 2.5" O.C.
78.61
84.8
422.90
84.58
5.38
1.12
Neutral White (4000°K) at 2.5" O.C.
81.75
82.8
439.82
87.96
5.38
1.12
COVELUM LED DESIGNER SERIES
LM/
WT/FT
WT/
MODULE
MODULE
Designer Model Series - SMD LEDs
Standard Model Series - Triple Chip LEDs
Delux Warm White (2600°K) at 2.5" O.C.
59.54
40.1
214.37
44.66
3.60
0.75
Warm White (2800°K) at 2.5" O.C.
64.20
54.8
231.12
48.15
3.60
0.75
Warm White (3000°K) at 2.5" O.C.
64.75
54.9
233.09
48.56
3.60
0.75
Warm White (3200°K) at 2.5" O.C.
65.29
59.5
235.06
48.97
3.60
0.75
Cool White (5000°K) at 2.5" O.C.
66.41
63.3 239.09 49.81
3.60
Items in bold denote Title 24 High efficacy rating. Measurements are based on
12V DC power calculations will vary based on power supply and run lengths.
0.75
LED DATA
WATTAGE
LED LIFE* / COLOR TEMP
Designer Model Series LED
module with 6 SMD LEDs
1.12W per
PCB
40,000 hrs.
All White color temperatures
+/- 50°K
120°
Standard Model Series LED
Superflux module with 6 Triple
Chip LEDs
0.75W per
PCB
30,000 hrs.
All White color temperatures
+/- 100°K
150°
RATED TO LM80 STANDARDS
VIEWING
ANGLE
1. Spacing - Lamp spacing: 2.5", 3", 4" O.C.
2. LED PCB - 12V DC LED modules in fuse style envelope
Designer Model Series - SMD LED: 1.12W/PCB Module
Standard Model Series - Triple Chip: 0.75W/PCB Module
3. Adjustability - +/-45° Directional LED modules (90° total adjustability) offer
the ability to manually set the angular throw of light individually, distributing
light over a 150° (Standard Model) or 120° (Designer Model) beam spread
4. Colors - Designer Model Series: 2200°K, 2400°K, 2700°K, 3000°K, 3500°K, 4000°K
Standard Model Series: 2600°K, 2800°K, 3000°K,
3200°K, 5000°K
5. Mounting - Optional aluminum mounting channel for linear mounting or
mounting clamps (2 per foot) for curved or arched applications
6. Lens - Optional linear lens mounts in channel to protect LEDs from direct
contact - Clear, Frosted or Opal
7. Max run length - Designer Model Series: 144 PCBs per 15A Class I circuit 48 PCBs per 5A Class II circuit
Standard Model Series: 216 PCBs per 15A Class I circuit 72 PCBs per 5A Class II circuit
8. Power Supply - Listed Class I or II 12V DC power supply required
9. Listing - CETLUS dry listed for indoor Class I or II applications
Lighting Facts registration number W34V-7RWKCL
10. Warranty - 5 Year Warranty
PROFILES
Standard Model Series
Designer Model Series
REQUIRED POWER
SUPPLY OPTIONS
COVELUM LED ORDER SPECIFICATION GUIDE
Example: CLL-SM-2.5-WW-30-12
PRODUCT CODE
LED TYPE
LED SPACING
COLOR TYPE
TEMPERATURE
REQUIRED
POWER SUPPLY
12
CLL
COVELUM™
LED
VOLTAGE
DM = Designer 2.5 = 2.5" OC DW = Delux
Warm
Model
3.0 = 3" OC
White
SM = Standard 4.0 = 4" OC
WW
=
Warm
Model
White
NW = Neutral
White
CW = Cool
White
Standard Model
Delux Warm White
26 = 2600°K
Warm White
28 = 2800°K
30 = 3000°K
32 = 3200°K
Cool White
50 = 5000°K
12 = 12V DC
Designer Model
Delux Warm
White
2200°K
2400°K
2700°K
Warm White
30 = 3000°K
Neutral White
35 = 3500°K
40 = 4000°K
PSU
See power
supply
specsheets
ADUL-80-1-5-12-D
ADUL-150-2-5-12-D
ADUL-240-3-5-12-D
ADUL-320-4-5-12-D
ADUL-240-1-15-12-D
JT-60-1-5-12-D
JTH-60-1-5-12-D
JT-240-4-5-12-D
JTH-240-4-5-12-D
MT-60-1-5-12-DD
MW-80-1-5-12-D
MW-150-1-10-12-D
MW-240-1-15-12-D
MW-320-1-20-12-D
OPTIONAL
DIMMERS
N-600
NH-600
N-1000
NH-1000
N-1500
DIM-OT-1-5-D
See power dimming
specifications for more
information
See power supply specifications
for more information
Copyright © 2014 Tivoli 08.27.14 - Page 1 of 5
Tivoli, LLC • 15602 Mosher Ave, Tustin, CA 92780 • ph 714 957-6101 fx 714 427-3458 • www.tivolilighting.com / sales@tivolilighting.com
COVELUM™
DESIGNER & STANDARD SERIES
WIRING ACCESSORIES
1 3/8"
1 1/2"
2 1/4"
CLL-JBOX Junction Box
Use to cover terminal block connections. One end of the terminal block screws directly into the
Covelum™ LED lead wires, the other end accepts AWG # 10, 12, 14 wire from power supply.
1 each terminal block included.
TERM-BLK Terminal Block available separately.
CLL-EC End Caps
Each length of Covelum™ LED can be
terminated with PVC end caps to protect
and insulate the conductors at the end
of a run.
MOUNTING ACCESSORIES
CLL-CC Cable Clamp
White PVC mounting clamp secures
Covelum™ cable to surface with a single
screw on each side of clamp. (Screws not
provided.)
Standard Model Series
with Mounting Channel
CLL-CHAN-8 Aluminum Mounting Channel
For straight run applications. Channel
screws in place, lamp sockets fit into
channel ensuring linear integrity and
reducing installation time. The finish is
standard satin aluminum. Comes in 8’
sections.
CLL-LENS-C-8 Clear Lens
CLL-LENS-F-8 Frosted Lens
CLL-LENS-O-8 Opal Lens
Clear, Frosted or Opal polycarbonate lens
for channel, shields and protects lamps
from direct contact. Comes in 8’ sections
(Opal lens shown).
CLL-CH-EC Channel End Caps available
Mounting Channel and Lens
ACCESSORIES & REPLACEMENTS
Designer
Model
Standard
Model
REPLACEMENT PCB MODULES
DESIGNER MODEL SERIES
CLL-DM-DW-22-12 Delux Warm White 2200°K
CLL-DM-DW-24-12 Delux Warm White 2400°K
CLL-DM-DW-27-12 Delux Warm White 2700°K
CLL-DM-WW-30-12 Warm White 3000°K
CLL-DM-NW-35-12 Neutral White 3500°K
CLL-DM-NW-40-12 Neutral White 4000°K
STANDARD MODEL SERIES
CLL-SM-DW-26-12 Delux Warm White 2600°K
CLL-SM-WW-28-12 Warm White 2800°K
CLL-SM-WW-30-12 Warm White 3000°K
CLL-SM-WW-32-12 Warm White 3200°K
CLL-SM-CW-50-12 Cool White 5000°K
REPLACEMENT STRAND*
CLL-RS-2.5 Replacement Strand - 2.5" O.C.
CLL-RS-3.0 Replacement Strand - 3.0" O.C.
CLL-RS-4.0 Replacement Strand - 4.0" O.C.
* Not including LED PCB modules
Copyright © 2014 Tivoli 08.27.14 - Page 2 of 5
Tivoli, LLC • 15602 Mosher Ave, Tustin, CA 92780 • ph 714 957-6101 fx 714 427-3458 • www.tivolilighting.com / sales@tivolilighting.com
COVELUM ™
DESIGNER & STANDARD SERIES
FIXTURE SELECTION
Lamp Spacing
To select the lamp spacing necessary for desired effect, choose a
close spacing for an even unbroken glow when you have a close
distance or a wider spacing for a softer light with a greater distance to
the wall area to be lit. (see lamp spacing chart for details)
LAMP SPACING GUIDE
LIGHTING EFFECTS ACCESSORIES
Mounting clamps are recommended as a standard mounting
accessory. This method is effective for curved or straight applications.
Mounting clamps should be placed every 6".
Mounting Channel is recommended for uneven mounting surfaces
or when applications require a cover. Clear lens covers are used to
protect the Covelum LED modules from the environment without
diminishing light output.
Frosted and Opal lens covers are used to not only protect the
Covelum LED module but to soften light for an even glow. Covelum
LED module selection in conjunction with the Opal lens, is for low
ambient or near dark light levels.
12”-36” (SM)
12”-60” (DM)
4”-6”
For interior critical white color applications within +/- 50K, recommended
for illumination within 6” of source and for white backgrounds. Set
back 6-12” , cove height up to 5’ for DM (Designer Model) and 3’ for
SM (Standard Model).
LUMEN DEPRECIATION
Tivoli designs LED fixtures to meet optimal heat dissipation and efficacy
requirements by LED suppliers. Designs are based upon testing to
meet or exceed L50 and L70 guidelines. Lumen depreciation can
be tracked through these guidelines, which represent the point at
which light output is below 50% (color) or 70% (whites) of initial light
output. LED lifespan calculations are based upon data supplied by
LED manufacturers. Typically, LED product failures occur within fixture
construction, interdependent component failure, or operation under
adverse conditions.
Designer Model Series LEDs rated at LM80 standards
Tivoli operates LEDs at a derated current to maximize LED lifespan.
Conditions such as excessive voltage, vibration, heat and other
adverse conditions may negatively effect LED lifespan.
LED BINNING
LEDs are made in lots and sorted into bins based on wavelength
ranges that achieve specific colors. Tivoli uses a range of 2200°K
to 2750° for Delux Warm White, 2800°K to 3350°K for Warm White,
3400°K to 4100°K for Neutral White and 4150°K to 5500°K for
Cool White. Individual colors are bin sorted to within + or – 50°K
for Designer Models and + or - 100°K for Standard Models. White
LEDs vary slightly in color temperature within a particular bin. Tivoli
references each sub-bin location on the packing list and also labels this
information on each product. For replacement stock or color matching
with existing product consult factory.
Copyright © 2014 Tivoli 08.27.14 - Page 3 of 5
Tivoli, LLC • 15602 Mosher Ave, Tustin, CA 92780 • ph 714 957-6101 fx 714 427-3458 • www.tivolilighting.com / sales@tivolilighting.com
COVELUM™
DESIGNER & STANDARD SERIES
IES INDOOR REPORT
PHOTOMETRIC FILENAME : L06123002.IES
POLAR GRAPH
POLAR GRAPH
138
DESIGNER MODEL SERIES - 3200°K
STANDARD MODEL SERIES - 3200°K
104
180
143
170
160
180 170
160
186
POLAR GRAPH
150
140
1
107
90
35
72
2
72
2
110
107
1
10
20
50
90
130
80
120
2
93
70
110
47
1
60
100
40
30
90
Maximum Candela = 143.32 Located At Horizontal Angle = 0, Vertical Angle = 0
# 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.)
# 2 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.)
LIGHTING FACTS LABEL
70
60
100
36
140
80
120
36
At Horizontal Angle = 0, Vertical Angle = 0
l Angles (0 - 180) (Through Max. Cd.)
Angle (0) (Through Max. Cd.)
150
140
130
143
3
69
10
20
50
40
30
90
Maximum Candela = 138 Located At Horizontal Angle = 0, Vertical Angle = 0
# 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.) : BLUE
# 2 - Vertical Plane Through Horizontal Angles (90 - 270) : MAGENTA
# 3 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) : RED
For more details on the IES Photo Metrics Graph, visit http://www.tivolilighting.com/prodsearch.htm
under COVE LIGHTING.
Maximum Candela = 138 Located At Horizontal Angle = 0, Vertical Angle = 0
# 1 - Vertical Plane Through Horizontal Angles (0 - 180) (Through Max. Cd.) : BLUE
# 2 - Vertical Plane Through Horizontal Angles (90 - 270) : MAGENTA
# 3 - Horizontal Cone Through Vertical Angle (0) (Through Max. Cd.) : RED
For more details on the IES Photo Metrics Graph, visit http://www.tivolilighting.com/prodsearch.htm
under COVE LIGHTING.
Copyright © 2014 Tivoli 08.27.14 - Page 4 of 5
Tivoli, LLC • 15602 Mosher Ave, Tustin, CA 92780 • ph 714 957-6101 fx 714 427-3458 • www.tivolilighting.com / sales@tivolilighting.com
COVELUM ™
DESIGNER & STANDARD SERIES
RECOMMENDED POWER SUPPLIES
CAT NO
PRIMARY AND
SECONDARY
TOTAL WATTAGE /
AMPERAGE PER BREAKER
ADUL-80-1-5-12-D
120-277V AC / 12V DC 60W / 1X5A
C
ADUL-150-2-5-12-D
120-277V AC / 12V DC 120W / 2X5A
C
ADUL-240-3-5-12-D
120-277V AC / 12V DC 180W / 3X5A
C
ADUL-320-4-5-12-D
120-277V AC / 12V DC 240W / 4X5A
C
DIMENSIONS
ELECTRONIC OR DIMMABLE
AC MAGNETIC
(Y OR N)
ULUS
10"W X 10"L X 4"D
Electronic
Y: F
ULUS
10”W X 10”L X 4”D
Electronic
Y: F
ULUS
10”W X 10”L X 4”D
Electronic
Y: F
ULUS
10”W X 10”L X 4”D
Electronic
Y: F
ULUS
10”W X 10”L X 4”D
Electronic
Y: F
ETLUS
4.25”W X 8.50”L X 3.25”D
Magnetic
Y: A, C & E
ETLUS
4.25”W X 8.50”L X 3.25”D
Magnetic
Y: B & D
ETLUS
8.50”W X 16.00”L X 4.50”D Magnetic
Y: A, C & E
ETLUS
8.50”W X 16.00”L X 4.50”D Magnetic
Y: B & D
ULUS
7.75”W X 2.50”L X 1.63”D
Y: SELF DIMMING
LISTING
ADUL-240-1-15-12-D 120-277V AC / 12V DC 180W / 1X15A
C
JT-60-1-5-12-D
120V AC / 12V DC
60W / 1X5A
C
JTH-60-1-5-12-D
277V AC / 12V DC
60W / 1X5A
C
JT-240-4-5-12-D
120V AC / 12V DC
240W / 4X5A
C
JTH-240-4-5-12-D
277V AC / 12V DC
240W / 4X5A
C
MT-60-1-5-12-DD
120V AC / 12V DC
60W / 1X5A
C
Electronic
MW-80-1-5-12-D
120-277V AC / 12V DC 60W / 1X5A
UL/CE
7.75”W X 2.50”L X 1.63”D
Electronic
Y: F
MW-150-1-10-12-D
120-277V AC / 12V DC 120W / 1X10A
UL/CE
9.00”W X 2.75”L X 1.63”D
Electronic
Y: F
MW-240-1-15-12-D
120-277V AC / 12V DC 180W / 1X15A
UL/CE
9.75”W X 2.75”L X 1.63”D
Electronic
Y: F
MW-320-1-20-12-D
120-277V AC / 12V DC 240W / 1X20A
UL/CE
10.00”W X 3.63”L X 1.75”D Electronic
Y: F
DIMMERS
SELECTOR
DIMMER
TYPE
CONTROL
SIGNAL
INPUT
VOLTAGE
OUTPUT
VOLTAGE
MAX
LOAD
BREAKER
RATING
DIMENSIONS
A
N-600
AC Magnetic
N/A
120V AC
120V AC
450W
N/A
Recessed Single Gang Box
B
NH-600
AC Magnetic
N/A
277V AC
277V AC
450W
N/A
Recessed Single Gang Box
C
N-1000
AC Magnetic
N/A
120V AC
120V AC
800W
N/A
Recessed Dual Gang Box
D
NH-1000
AC Magnetic
N/A
277V AC
277V AC
800W
N/A
Recessed Dual Gang Box
E
N-1500
AC Magnetic
N/A
120V AC
120V AC
1200W
N/A
Recessed Dual Gang Box
F
DIM-OT-1-5-D
Control Interface 0-10V DC
12V DC
12V DC
60W
5A*
7"L X 1½"W X ¾"H
*DIM-OT applications require 1 each DIM-OT per 5 amp circuit
PRODUCT SPECIFICATION GUIDE
SPACING
WATTS PER
FOOT
PRODUCT MAX RUN LIMITATIONS
(Ft/W/LED’s)
DESIGNER MODEL SERIES
2.5” O.C.
5.38W/ft
30’
10’
144 PCBs per 15A Class I circuit
48 PCBs per 5A Class II circuit
3” O.C.
4.48W/ft
36’
12’
144 PCBs per 15A Class I circuit
48 PCBs per 5A Class II circuit
4" O.C.
3.33W/ft
48’
16’
144 PCBs per 15A Class I circuit
48 PCBs per 5A Class II circuit
STANDARD MODEL SERIES
2.5” O.C.
3.60W/ft
45’
15’
216 PCBs per 15A Class I circuit
72 PCBs per 5A Class II circuit
3” O.C.
3.00W/ft
54’
18’
216 PCBs per 15A Class I circuit
72 PCBs per 5A Class II circuit
4" O.C.
2.25W/ft
72’
24’
216 PCBs per 15A Class I circuit
72 PCBs per 5A Class II circuit
Transformer
JBox
Light Load
Copyright © 2014 Tivoli 08.27.14 - Page 5 of 5
Tivoli, LLC • 15602 Mosher Ave, Tustin, CA 92780 • ph 714 957-6101 fx 714 427-3458 • www.tivolilighting.com / sales@tivolilighting.com