DIF-110
POWER SUPPLY 60 WATTS
PS-60W
POWER SUPPLY 21 WATTS
PS-21W
12" UNDERCABINET
(INCLUDED W/ UC)
8’ CABLE, EXT • CX-8
45" UNDERCABINET
EXTENSION CABLE [DL or UC]
POWER CABLE, SW
22" UNDERCABINET
6" CABLE, SPLITTER • CY-6
RARE EARTH SUPER-MAGNETS
PATCH CABLE
UNDERCABINET
SPLITTER CABLE [DL or UC]
( FOR 21W / 60W PS ONLY)
OCCUPANCY SENSOR
12’ CABLE, POWER N/SW, UC • CPN-12
SPLITTER CABLE
MOUNTING PLATE
MP-S
POWER CABLE, SW
POWER CABLES [UC only]
POWER SUPPLY 8 WATTS
PS-8W
5" BASE
WBC-S
28" CABLE, PATCH, UC • CP-28
14" CABLE, PATCH, UC • CP-14
CLAMP
CL-S
PATCH CABLES [UC only]
POWER SUPPLIES
DL-C
DESK LAMP
WEIGHTED BASES
I N ST R U CT I O N S
MOUNTING OPTIONS
WARRANTY AND RETURN INFORMATION
PLS
SY ST E M
6" CABLE, PATCH, UC • CP-6
3" CABLE, PATCH, UC • CP-3
PLS USE & CARE
P L S L I G H T I N G F A C T S CM L A B E L S
DESK LAMP
Finelite, Inc. warranties all Personal Lighting System components to be free from defects in
materials and workmanship for a period of three years. Contact Finelite Inside Sales for return
information if you have a warranty claim.
TROUBLESHOOTING GUIDELINES
What if the fixtures (Desk Lamps and Undercabinet) don't illuminate?
• Check all connections. Is the connection to the supply voltage secure and fully inserted?
• Is the power indicator LED illuminated? (21W and 60W power supplies only) — If the
LED is not illuminated, contact Finelite.
• Is the power supply “OCC SENSOR” switch in the “NO” position?
• Are all low voltage connections secured and fully inserted?
• Are all on/off fixture switches switched to “ON”?
• Check to see that you have not exceeded a total of the maximum rated load of the power
supply - disconnect fixtures until you are below maximum rated load.
What if the fixtures “flash” when powered?
• Check to see that you have not exceeded a total of the maximum rated load of the power
supply - disconnect fixtures until you are below maximum rated load.
• Cycle power on/off to power supply if necessary.
What if the Occupancy Sensor does not turn off system?
What if the Occupancy Sensor turns the system off while seated at a station?
• Make sure the occupancy sensor is set to a delay setting between min and max (10-15
minutes works best for most installations).
• Make sure that the sensor window is not obstructed and facing towards your most common
seated location.
• For best results mount the occupancy sensor underneath your desk.
CARE AND CLEANING OF THE PLS SYSTEM
Your PLS system should operate trouble free for the life of the system. You may periodically wipe
the system clean with a slightly damp soft cloth. Do not use any solvent or alcohol based cleaning
products on plastic or painted surfaces or on the labels.
Finelite, Inc. • 30500 Whipple Rd • Union City, CA 94587-1530
510-441-1100 • Fax 510-441-1510 • www.finelite.com
UNDERCABINET - 12", 22", & 45"
© 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98384. 03/16
• Is the “OCC SENSOR” switch in the “YES” position?
• Is the occupancy sensor connected to the power supply?
• Does the indicator light on the occupancy sensor illuminate? (Note: It will only illuminate
when sensing movement.)
• Try turning the delay to a value between 30 minutes (max) and 30 seconds (min) on back
of sensor (~10-15 minutes works best for most installations).
• Consult occupancy sensor instruction sheet (supplied with sensor) for more information.
P E R S O NA L L I G HT I N G SY ST E M
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful Interference in which case the user will be required to correct the interference at his own expense.
P L S I N ST R U CT I O N S
DESK LAMP
UNDERCABINET
Wood
Steel
MOUNTING
Rare earth super-magnets provided
pre-installed for moutning directly on steel.
NOTE: Remove rare earth magnets when
installing with wood screws. Contact Factory.
POWER SUPPLIES
Front
1” - 2.5”
OCC
SENSOR
OCC
SENSOR
No
Yes
Back
Drill
1.125 in. dia.
(29mm)
1” - 2.5”
Occupancy
Sensor
max
Time
Delay
min
FOR MORE INFO, SEE PLS OCCUPANCY
SENSOR INSTRUCTION SHEET