Appendix A - ATtiny45 Automotive specification at 150°C

advertisement
ATtiny45
Appendix A - ATtiny45 Automotive specification at 150°C
DATASHEET
Description
This document contains information specific to devices operating at temperatures up to
150°C. Only deviations are covered in this appendix, all other information can be found in
the complete Automotive datasheet. The complete Automotive datasheet can be found on
www.atmel.com
7696D-AVR-06/14
1.
Electrical Characteristics
1.1
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating
only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Parameters
Min.
Operating temperature
Typ.
Max.
Unit
–55
+150
°C
Storage temperature
–65
+175
°C
Voltage on any pin except RESET with respect
to ground
–0.5
VCC + 0.5
V
Voltage on RESET with respect to ground
–0.5
+13.0
V
Maximum operating voltage
6.0
V
DC current per I/O pin
30.0
mA
DC current VCC and GND pins
200.0
mA
1.2
DC Characteristics
TA = –40°C to +150°C, VCC = 2.7V to 5.5V (unless otherwise noted)(6)
Parameter
Condition
Input low voltage, except
XTAL1 and RESET pin
Symbol
Min.
VCC = 2.7V - 5.5V
VIL
Input high voltage, except
XTAL1 and RESET pins
VCC = 2.7V - 5.5V
Input low voltage,
XTAL1 pin
Typ.
Max.
Unit
–0.5
0.3VCC(1)
V
VIH
0.6VCC(2)
VCC + 0.5
V
VCC = 2.7V - 5.5V
VIL1
–0.5
0.1VCC(1)
V
Input high voltage,
XTAL1 pin
VCC = 2.7V - 5.5V
VIH1
0.7VCC(2)
VCC + 0.5
V
Input low voltage,
RESET pin
VCC = 2.7V - 5.5V
VIL2
–0.5
0.2VCC(1)
V
Input high voltage,
RESET pin
VCC = 2.7V - 5.5V
VIH2
0.9VCC(2)
VCC + 0.5
V
Input low voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
VIL3
–0.5
0.3VCC(1)
V
Input high voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
VIH3
0.6VCC(2)
VCC + 0.5
V
Output low voltage(3),
I/O pin except RESET
IOL = 10mA, VCC = 5V
IOL = 5mA, VCC = 3V
VOL
0.8
0.5
V
Output high voltage(4),
I/O pin except RESET
IOH = –10mA, VCC = 5V
IOH = –5mA, VCC = 3V
VOH
Input leakage
current I/O pin
VCC = 5.5V, pin low
(absolute value)
IIL
1
µA
Input leakage
current I/O pin
VCC = 5.5V, pin high
(absolute value)
IIH
1
µA
4.0
2.2
V
Reset pull-up resistor
RRST
30
60
k
I/O pin pull-up resistor
RPU
20
50
k
2
ATtiny45 [DATASHEET]
7696D–AVR–06/14
1.2
DC Characteristics (Continued)
TA = –40°C to +150°C, VCC = 2.7V to 5.5V (unless otherwise noted)(6)
Parameter
Power supply current(6)
Power-down mode
Condition
Active 4MHz, VCC = 3V
Active 8MHz, VCC = 5V
Active 16MHz, VCC = 5V
Idle 4MHz, VCC = 3V
Idle 8MHz, VCC = 5V
Idle 16MHz, VCC = 5V
WDT enabled, VCC = 3V
WDT enabled, VCC = 5V
WDT disabled, VCC = 3V
WDT disabled, VCC = 5V
Symbol
Max.
Unit
ICC
8
16
25
mA
ICC IDLE
6
12
14
mA
90
140
µA
80
120
µA
40
mV
50
nA
ICC PWD
Min.
Typ.
(5)
Analog comparator
input offset votage
VCC = 5V
Vin = VCC/2
VACIO
Analog comparator
input leakage current
VCC = 5V
Vin = VCC/2
IACLK
Analog comparator
propagation delay
VCC = 4.0V
tACPD
<10
–50
500
ns
ATtiny45 [DATASHEET]
7696D–AVR–06/14
3
2.
Memory Endurance
EEPROM endurance: 50,000 Write/Erase cycles
2.1
Maximum Speed versus VCC
Maximum frequency is dependent on VCC. As shown in Figure 2-1, the maximum frequency versus VCC curve is linear
between 2.7V < VCC 4.5V(6).
Figure 2-1. Maximum Frequency versus VCC
16MHz
8MHz
Safe Operating Area
2.7V
4
ATtiny45 [DATASHEET]
7696D–AVR–06/14
4.5V
5.5V
3.
ADC Characteristics(6)
TA = 125°C to 150°C, VCC = 4.5V to 5.5V (unless otherwise noted)
Parameter
Condition
Symbol
Min
Resolution
Absolute accuracy
(Including INL, DNL,
quantization error, gain and
offset error)
Typ
Max
10
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
Unit
Bits
2
3.5
LSB
2
3.5
LSB
Noise reduction mode
Integral non-linearity (INL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.6
2.5
LSB
Differential non-linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
0.30
1.0
LSB
Gain error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
–1.3
3.5
LSB
Offset error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
1.8
3.5
LSB
Conversion time
Free running conversion
–3.5
13 cycles
Clock frequency
µs
50
200
kHz
Analog supply voltage
AVCC
VCC – 0.3
VCC + 0.3
V
Reference voltage
VREF
1.0
AVCC
V
VIN
GND
VREF – 50mV
V
Internal voltage reference
VINT
1.0
1.1
1.2
V
Reference input resistance
RREF
25.6
32
38.4
k
Input voltage
Input bandwidth
38.5
kHz
Analog input resistance
RAIN
100
Notes: 1. “Max” means the highest value where the pin is guaranteed to be read as low
M
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions (nontransient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOL, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current
greater than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at Vcc = 5V) under steady state conditions
(non-transient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400mA.
2] The sum of all IOH, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOH, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for Power-down is 2.5V.
ATtiny45 [DATASHEET]
7696D–AVR–06/14
5
4.
ATtiny45 Typical Characteristics
4.1
Active Supply Current
Figure 4-1. Active Supply Current versus Frequency (1 - 20 MHz)
ICC (mA)
16
14
5.5V
12
5.0V
4.5V
10
4.0V
8
3.3V
6
2.7V
4
2
0
0
2
4
6
8
10
12
14
16
18
20
Frequency (MHz)
Figure 4-2. Idle Supply Current versus Frequency (1 - 20 MHz)
0.14
0.12
5.5V
5.0V
0.1
Idle (mA)
4.5V
0.08
0.06
3.3V
0.04
2.7V
0.02
0
0
2
4
6
8
10
12
Frequency (MHz)
6
ATtiny45 [DATASHEET]
7696D–AVR–06/14
14
16
18
20
Power-Down Supply Current
Figure 4-3. Power-down Supply Current versus VCC (Watchdog Timer Disabled)
14
12
150°C
ICC (µA)
10
8
6
4
125°C
2
-40°C
85°C
25°C
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 4-4. Power-down Supply Current versus VCC (Watchdog Timer Enabled)
20
150°C
18
16
14
ICC (µA)
4.2
12
125°C
-40°C
85°C
25°C
10
8
6
4
2
0
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
7
4.3
Pin Pull-up
Figure 4-5. I/O Pin Pull-up Resistor Current versus Input Voltage (VCC = 5V)
160
150°C
140
-40°C
120
IOP (µA)
100
80
60
40
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
VOP (V)
Figure 4-6. Output Low Voltage versus Output Low Current (VCC = 5V)
0.7
150°C
125°C
0.6
VOL (V)
85°C
0.5
25°C
0.4
-40°C
0.3
0.2
0.1
0
0
2
4
6
8
10
IOL (V)
8
ATtiny45 [DATASHEET]
7696D–AVR–06/14
12
14
16
18
20
Figure 4-7. Output Low Voltage versus Output Low Current (VCC = 3V)
1.2
150°C
125°C
1
85°C
VOL (V)
0.8
25°C
0.6
-40°C
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IOL (V)
Figure 4-8. Output High Voltage versus Output High Current (VCC = 5V)
5.1
5
4.9
VOH (V)
4.8
4.7
4.6
-40°C
4.5
25°C
85°C
125°C
150°C
4.4
4.3
4.2
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Figure 4-9. Output High Voltage versus Output High Current (VCC = 3V)
3.5
3
VOH (V)
2.5
-40°C
25°C
85°C
125°C
150°C
2
1.5
1
0.5
0
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
9
Figure 4-10. Reset Pull-Up Resistor Current versus Reset Pin Voltage (VCC = 5V)
120
+150°C
100
-40°C
IRESET (µA)
80
60
40
20
0
0
1
2
3
4
5
6
VRESET (V)
4.4
Pin Thresholds and Hysteresis
Figure 4-11. I/O Pin Input Threshold versus VCC (VIH, I/O Pin Read as ‘1’)
3
150°C
-40°C
Threshold (V)
2.5
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
VCC (V)
10
ATtiny45 [DATASHEET]
7696D–AVR–06/14
4
4.5
5
5.5
Figure 4-12. I/O Pin Input Threshold versus VCC (VIL, I/O Pin Read as ‘0’)
3
150°C
-40°C
Threshold (V)
2.5
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 4-13. Reset Input Threshold Voltage versus VCC (VIH, Reset Pin Read as ‘1’)
2.5
150°C
-40°C
Threshold (V)
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 4-14. Reset Input Threshold Voltage versus VCC (VIL, Reset Pin Read as ‘0’)
2.5
150°C
-40°C
Threshold (V)
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
11
4.5
Internal Oscillator Speed
Figure 4-15. Watchdog Oscillator Frequency versus VCC
0.17
FRC (MHz)
0.15
0.13
-40°C
0.11
150°C
0.09
0.07
2
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 4-16. Calibrated 8 MHz RC Oscillator Frequency versus Temperature
8.5
8.4
5.0V
3.0V
8.3
FRC (MHz)
8.2
8.1
8
7.9
7.8
7.7
7.6
7.5
-40 -30 -20
-10
0
10
20
30
40
50
60
70
Temperature (°C)
12
ATtiny45 [DATASHEET]
7696D–AVR–06/14
80
90
100 110 120 130 140 150
Figure 4-17. Calibrated 8 MHz RC Oscillator Frequency versus VCC
8.6
8.2
150°C
125°C
85°C
8
25°C
FRC (MHz)
8.4
7.8
-40°C
7.6
7.4
7.2
7
2.5
3
2.5
3
3.5
4
4.5
5
5.5
VCC (V)
Figure 4-18. Calibrated 8 MHz RC Oscillator Frequency versus OSCCAL Value
16
14
150°C
-40°C
FRC (MHz)
12
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
256
OSCCAL (X1)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
13
4.6
BOD Thresholds and Analog Comparator Offset
Figure 4-19. BOD Threshold versus Temperature (BODLEVEL is 4.3V)
4.4
4.35
Rising
Threshold (V)
4.3
Falling
4.25
4.2
4.15
4.1
4.05
4
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Temperature (°C)
Figure 4-20. BOD Threshold versus Temperature (BODLEVEL is 2.7V)
2.8
Rising
2.75
Threshold (V)
2.7
Falling
2.65
2.6
2.55
2.5
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Temperature (°C)
Figure 4-21. Bandgap Voltage versus VCC
Bandgap Voltage (V)
1.3
1.2
150°C
-40°C
1.1
1
0.9
1.5
2
2.5
3
3.5
VCC (V)
14
ATtiny45 [DATASHEET]
7696D–AVR–06/14
4
4.5
5
5.5
Peripheral Units
Figure 4-22. Analog to Digital Converter GAIN versus Temperature, Single Ended
0
-0.5
LBS
-1
-1.5
-2
-2.5
-3
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
Figure 4-23. Analog to Digital Converter GAIN versus Temperature, Differential Mode
-1
-1.2
-1.4
-1.6
Diff x20
LBS
-1.8
-2
-2.2
-2.4
-2.6
Diff x1
-2.8
-3
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
Figure 4-24. Analog to Digital Converter OFFSET versus Temperature, Single Ended
2.5
2
1.5
LBS
4.7
1
0.5
0
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
15
Figure 4-25. Analog to Digital Converter OFFSET versus Temperature, Differential Mode
2
1.5
1
LBS
0.5
0
Diff x1
-0.5
-1
-1.5
-2
Diff x20
-2.5
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
Figure 4-26. Analog to Digital Converter DNL versus Temperature, Single Ended
0.57
0.56
0.55
0.54
LBS
0.53
0.52
0.51
0.5
0.49
0.48
0.47
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
Figure 4-27. Analog to Digital Converter DNL versus Temperature, Differential Mode
1.6
1.4
Diff x20
1.2
LBS
1
0.8
0.6
0.4
Diff x1
0.2
0
-40 -30 -20
-10
0
10
20
30
40
50
60
70
Temperature (°C)
16
ATtiny45 [DATASHEET]
7696D–AVR–06/14
80
90
100 110 120 130
140 150
Figure 4-28. Analog to Digital Converter INL versus Temperature, Single Ended
0.72
0.7
LBS
0.68
0.66
0.64
0.62
0.6
0.58
-40 -30 -20
-10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Temperature (°C)
Figure 4-29. Analog to Digital Converter INL versus Temperature, Differential Mode
2.5
2
Diff x20
LBS
1.5
Diff x1
1
0.5
0
-40 -30
-20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130
140 150
Temperature (°C)
ATtiny45 [DATASHEET]
7696D–AVR–06/14
17
5.
Grade 0 Qualification
The ATtiny45 has been developed and manufactured according to the most stringent quality assurance requirements of
ISO-TS-16949 and verified during product qualification as per AEC-Q100 grade 0.
AEC-Q100 qualification relies on temperature accelerated stress testing. High temperature field usage however may result
in less significant stress test acceleration. In order to prevent the risk that ATtiny45 lifetime would not satisfy the application
end-of-life reliability requirements, Atmel has extended the testing, whenever applicable (high temperature operating life test,
high temperature storage life, data retention, thermal cycles), far beyond the AEC-Q100 requirements. Thereby, Atmel®
verified the ATtiny45 has a long safe lifetime period after the grade 0 qualification acceptance limits.
The valid domain calculation depends on the activation energy of the potential failure mechanism that is considered.
Examples are given in figure 1. Therefore any temperature mission profile which could exceed the AEC-Q100 equivalence
domain shall be submitted to Atmel for a thorough reliability analysis.
Figure 5-1. AEC-Q100 Lifetime Equivalence
1000000
100000
Hours
10000
1000
100
10
1
0
20
40
60
80
100
120
Temperature (°C)
HTOL 0.59eV
18
ATtiny45 [DATASHEET]
7696D–AVR–06/14
HTSL 0.45eV
140
160
6.
Ordering Information
6.1
ATtiny45
Table 6-1.
ATtiny45
Speed (MHz)
16(2)
Notes:
1.
2.
Table 6-2.
Power Supply
Ordering Code
Package(1)
Operation Range
Extended
(–40°C to +150°C)
Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).
Also halide free and fully green.
2.7 - 5.5V
ATtiny45-15MT2
PC
For speed versus VCC, see Figure 2-1 on page 4 and complete product datasheet.
Package Information
Package Type
PC
20-lead, 4.0x 4.0mm body, lead pitch 0.60mm, quad flat no-lead package
ATtiny45 [DATASHEET]
7696D–AVR–06/14
19
Figure 6-1. Package PC
D
0.10 C
1.00 REF
1.00 REF
SEATING PLANE
0.08 C
C
PIN #1 Identifier
Laser Marking
E
0.15
(4x)
J
A
Top View
Side View
DRAWINGS NOT SCALED
b
COMMON DIMENSIONS IN MM
SYMBOL
MIN.
NOM.
MAX.
A
0.70
0.75
0.80
J
0.00
D/E
3.90
4.00
4.10
D2/E2
2.50
2.60
2.70
E2
0.05
N
20
e
e
1
N
NOTES
0.50 BSC
L
0.35
0.45
0.55
b
0,20
0.25
0.30
Option A
Option B
Option C
D2
L
Bottom View
1
1
See Option A, B, C
1
N
N
N
Pin 1# Chamfer
(C 0.30)
Pin 1# Notch
(0.20 R)
Pin 1#
Triangle
Compliant JEDEC Standard MO-220 Variation WGGD-5
06/25/09
TITLE
Package Drawing Contact:
packagedrawings@atmel.com
20
ATtiny45 [DATASHEET]
7696D–AVR–06/14
PC, 20-Lead - 4.0x4.0mm Body, 0.50mm Pitch
Quad Flat No Lead Package (QFN)
GPC
DRAWING NO.
REV.
PC
I
7.
Revision History
Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this
document.
Revision No.
History
7696D-AVR-06/14
Put datasheet in the latest template
7696C-AVR-10/12
Figure 6-1 “Package PC” on page 23 updated
7696B-AVR-04/09
Added EEPROM endurance. See Section 2. “Memory Endurance” on page 4.
ATtiny45 [DATASHEET]
7696D–AVR–06/14
21
XXXXXX
Atmel Corporation
1600 Technology Drive, San Jose, CA 95110 USA
T: (+1)(408) 441.0311
F: (+1)(408) 436.4200
|
www.atmel.com
© 2014 Atmel Corporation. / Rev.: 7696D–AVR–06/14
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, and others are registered trademarks or trademarks of Atmel Corporation in U.S.
and other countries. Other terms and product names may be trademarks of others.
DISCLAIMER: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right
is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE
ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT
SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this
document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information
contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended,
authorized, or warranted for use as components in applications intended to support or sustain life.
SAFETY-CRITICAL, MILITARY, AND AUTOMOTIVE APPLICATIONS DISCLAIMER: Atmel products are not designed for and will not be used in connection with any applications where
the failure of such products would reasonably be expected to result in significant personal injury or death (“Safety-Critical Applications”) without an Atmel officer's specific written
consent. Safety-Critical Applications include, without limitation, life support devices and systems, equipment or systems for the operation of nuclear facilities and weapons systems.
Atmel products are not designed nor intended for use in military or aerospace applications or environments unless specifically designated by Atmel as military-grade. Atmel products are
not designed nor intended for use in automotive applications unless specifically designated by Atmel as automotive-grade.
Download