Remote Power supply system
210W charging specification
Wireless charging achieve
labor savings!
<Image of AGV>
Head
Charging unit
Now charging
wirelessly!
It connects with
24V lead battery
Power Supply
unit
(AGV body, I had offers from SHOWA AIRCRAFT INDUSTRY CO.,LTD.)
Benefits of system introduction
● Battery replacement connectors and
connection for charging is not required, I was
able to achieve power saving!
● Allows 24 hours of continuous operation with
automatic charge!
● No risk of electric shock, safe and secure
● To the charge in stop place AGV, prevents, or
low battery, the charging forgetting.
● The status signal of the voltage monitor, etc.,
and improved operability
Passive Head
RCS240PH
Charging unit
RCS210-PB24
<Charging side>
Active Head
RCS240AH
Power Supply unit
RCS240-AC1
<Power supply side>
The battery charge image in AGV
Lead battery loading
Wireless charging
&Status signal transmission
<Charge
Termination>
AGV
Fixed
side
(Active)
Movable
side
(Passive)
Remote Power supply system
System chart
Wireless charging Remote system
Wireless Charging
24V lead
battery
External
control
devices
Power
Active Head
Passive Head
Power
Temperature
detection
AC Power
External
control
devices
Thermistor
Signal
Signal
Power Supply unit
Charging unit
＜Charging side＞
Signal
＜Power Supply side＞
And benefits
Improvement of
existing lines
and smooth easy
installation work
Transmitting a signal to an external
device in the communication function
Battery life up at
a constant current and constant
voltage
Reliable error detection, the protection function
+
-
Charging characteristics (Reference)
30Ah (5 hour rate)　Battery discharge about 50%
CC · CV charging characteristics
24VDC/300mA
非接触給電
24VDC/2A
100Hz
voltage
current
ベース部
リモート部
Charging voltage
(V)
Charging current
(A)
電源
検出信号
制御信号
40Hz
＜可動側＞
Time (minutes)
＜固定側＞
The charge control, it steps will do CC · CV control in ( ※ 1). It becomes intermittent charge state
charging current drops to 1.5A battery voltage and reached a predetermined voltage. Also, stop the feeding automatically and goes into standby mode if Passive head came out power transmission coverage
area of Active head. Return to the CV charge state when the intermittent charging state, and the output
current becomes 3A, it does the above.
※ After charged at a constant current value 1 = first reaches a specified voltage, a method to continue charging while
lowering the current to maintain the voltage
Remote Power supply system
Specification
Power Supply unit
230
194
8.5
7.0
18
15
B View
90
15
8-7X15
B View
A View
210
190
170
172.5
A View
188
300
90
90
6.5
Charging unit
160
80
50.5
B View
A View
2
A View
B View
1
Type code
RCS210-PB24
Type code
RCS240-AC1
Output voltage
≦ 30V (It varies depending on battery temperature)
Power supply voltage
Current consumption
Input
100V AC / 200V AC
4A
Start-up signal
Voltage monitor signal, Inzone signal,
charging signal,
Intermittent charging signal, Battery error signal
Forced air cooling
Status display of input and output signal
Output current
Input
≦ 7A (It varies depending on battery voltage)
Voltage monitor request
Voltage monitor signal, charging signal,
Output
intermittent charging signal,Battery error signal Output
Cooling method
Natural air cooling
Cooling method
Input : Overvoltage protection
Protection circuit
Battery : High temperature / low temperature protec- LED display
tion, not connected, reverse connection protection
Operating temperature
Operating temperature 0...+40℃
Protection class
Protection class
IP20
Active
Passive
Round 3-pin connector
Connection Signal
Signal
Round 5-pin connector
Power
Connection
External input 2-pole (Main part side : Female)
Material　Main part case
Battery
For battery connection terminal box 2-pole
Weight
Material Main part case Aluminum
Accessories
Weight
1.6Kg
Output cable (1.5m), Thermistor with cable (1.5m),
Accessories
External device communication connector, 4 screws
M6x15
Power cable (2m), External device communication connector,4 screws M6x15
Active Head
100
86
140
126
4-φ6.5
86
140
126
100
Passive Head
0...+50℃
IP20
Round 3-pin connector
D-Sub 9-pin connector
3P inlet
SECC
2.6Kg
1000
40
40
8
8
1000
Type code
RCS240PH
Output voltage
Output current
Transmission distance
Permissible center off-set
Output current
Charging unit reference
Operating voltage
Charging unit reference
Current consumption
0...10mm
Load current
≦ 10mm（The sum of X and Y are less than 10mm） Frequency response
Charging unit reference
LED display
Operating temperature 0...+50℃
Protection class
IP65
Active：Round 3-pin, Signal：Round 5-pin
Connection
Each connector cable included (1m)
Material Active surface PPS
Back
Aluminum
Weight
1.2Kg
Type code
Operating temperature
Protection class
RCS240AH
Power Supply unit reference
Power Supply unit reference
-------
0...+50℃
IP65
Active：Round 3-pin, Signal：D-sub 9-pin
Connection
Each connector cable included (1m)
Material Active surface PPS
Back
Aluminum
Weight
1.2Kg
Remote Power supply system
Installation Notices
Installation
Wiring
In order to obtain a good cooling effect, please keep spaces between the surrounding and the body unit as shown
as below, so as not to block the airflow.
More than5ｃｍ以上
5cm
Output cable
(1)24V lead battery
(2)Thermistor with Cable
10ｃｍ以上
More than 10cm
Charging unit
Power Supply unit
More
than 5cm
5ｃｍ以上
5ｃｍ以上
More
than 5cm
Mutual interference
(1)　External device
communication cable
(AWG24 ～ 16)
If you are installing in parallel head, to avoid the effects
of mutual interference, please attach the head with an
interval greater than or equal to the value shown in the
table below always.
Power cable
(1)　External device
communication
cable
(AWG28 ～ 16)
A
Passive Head
B
Type code A(mm)
RCS240AH
300
RCS240PH
B
Attachment
Please make the following is greater than or equal to
the number of R(mm) bending of the cable line.
・Active Cable line and Passive Cable line : R50
・Signal Cable line : R30
R
(1)Parts of the dotted line (External device communication cable and
24V lead batteries) within the product is not included with this
product.They are contents prepared and processed of a visitor.
(2)Please use the attached article always thermistor. Please be
attached to the upper surface of the terminal near the 24V lead
batteries. In that case, please do not touch any terminals.
Center off-set and transmitting distance
The permissible center off-set of the feed head and charging
head, please be installed so that the total (X + Y) axis deviation of the width of the X-axis · Y-axis is the following table.
G
Surrounding metal
To avoid influence of surrounding metal,
keep minimum spacing.
A
B
Type code
RCS240AH
RCS240PH
Active Head
X-axis direction
Y-axis
direction
Direction Distance
G
≦ 10mm
X+Y
A(mm) B(mm)
100
40
Request for use on
● This product,
which is one of those high frequency utilization equipment of Radio Law, Upon use You will need to install
軸ズレ　XまたはYどちらか１方向　(mm)
application. Please use it after you have made the application without fail.
Installation details of the application procedure, see Telecommunications website of the Ministry of Internal Affairs and
Communications, Please.
● The control communication device that is installed in the product, there is no need for (diploma) radio station authorization of
the Minister so apply to "a weak radio station (weak radio equipment)" to.
However, please be careful on the occasion of the operation because it may affect medical equipment and electronic
equipment (such as pacemakers).
● This product has become a Japan national specification. It can not be used outside of Japan. When used outside of Japan,
I guess we assume any liability You.
● When using, refer to instruction manual, user's guide always.
USA Branch
274 Gomyo Tokigawa-machi
3655 Torrance Blvd. 3rd Floor
Hiki-gun Saitama 355-0343 Japan
Torrance, CA 90503
E-mail : b-plus@b-plus-kk.jp
E-mail : b-plus-usa@b-plus-kk.com
http://www.b-plus-kk.jp
http://www.b-plus-kk.com
*Specification is subject to change without notice.
BN1301Ae
2013.07