HEAVY DUTY HYDRAULIC MOTORS
CONTENTS
Page
•
Hydraulic Motors Series MSWM .................................................................................. 4
•
Hydraulic Motors Series MTK ................................................................................... 8
•
Hydraulic Motors Series MTM ................................................................................... 17
•
Hydraulic Motors Series TMF ................................................................................... 29
•
Hydraulic Motors Series MVM .................................................................................. 34
•
Hydraulic Motors Series MVMC ................................................................................... 39
•
Hydraulic Motors Series VMF ................................................................................... 44
•
Motor Special Features ............................................................................................... 48
•
Motors with Speed Sensor .................................................................................................. 49
•
Application Calculation ................................................................................................... 51
“M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material.
“M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such
alterations can be made without subsequential changes being necessary in specifications already agreed.
DISC VALVE HYDRAULIC MOTORS
GENERAL INFORMATION:
Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors
operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits
the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's
output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs
on tapered roller bearings and can absorb high axial and radial forces.
DISTRIBUTOR VALVE
MSWM, MTK, MTM, TMF, MVM, MVMC, VMF series motors have disk valve: the distributor valve has been separated from
output shaft and is driven by short cardan shaft. A balance plate counterbalances the hydraulic forces around the distributor
valve. It gives the motors high efficiency - even at high pressures, and good starting characteristics.
GEAR WHEEL SET
There are two forms of gear wheel set: Gerotor set have plain teeth and Roll-gerotor set with teeth fitted with rollers.
MSWM, MTK, MTM, TMF, MVM, MVMC, VMF series motors have roll-gerotor set. The rollers reduce local stress and the
tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency
even at continuous high pressures.
FEATURES:
Standard Motor
The standard motor mounting flange is located as close to the output shaft as possible. This type of
mounting supports the motor close to the shaft load. This mounting flange is also compatible with many standard gear
boxes.
Wheel Motor
The wheel motor mounting flange is located near the center of the motor which permits part or all of
the motor to be located inside the wheel or roller hub. In traction drive applications, loads can be positioned over the motor
bearings for best bearing life. This wheel motor mounting flange provides design flexibility in many applications.
Short Motor
This motor is assembled without the output shaft, bearings and bearing housing and has the same
drive components as the standard motors. The short motor is especially suited for applications such as gear boxes, winch,
reel and roll drives. Short motor applications must be designed with a bearing supported internal spline to mate with the
short motor drive. Product designs using these hydraulic motors provide considerable cost savings.
Low Leakage
LL Series hydraulic motors are designed to operate at the whole standard range of working
conditions (pressure drop and frequency of rotation), but with considerable decreased volumetric losses in the drain ports.
This motors are suitable for hydraulic systems with series-conected motors with demands for low leakage.
Low Speed
Valve
LSV feature optimizes the motor for low-speed performance. Motors with this valving provide very
low speed while maintaining high torque. They are designed to run continuously at low speed (up to
200 RPM) at normal pressure drop and reduced flow. Optimal run is guaranteed at frequency of rotation from 20 to 50
RPM. Motors with this valving have an increased starting pressure and are not recommended for using at pressure drop
less than 40 bar [580 PSI].
Motors with
Speed Sensor
Motors are available with integrated inductive speed sensor. The output signal is a standardized
voltage signal that can be used to control the speed of a motor. The torque and the radial load of the
motor are not affected by the installation of speed sensor.
3
HYDRAULIC MOTORS MSWM
APPLICATION
»
»
»
»
»
»
»
»
Sawmill machines
Woodworking machines
Metal working machines
Agriculture machines
Road building machines
Mining machinery
Food industries
Special vehicles etc.
CONTENTS
OPTIONS
Specification data ....................................... 5
Dimensions and mounting ...........................6
Permissible shaft loads .............................. 6
Shaft extensions ......................................... 7
Order code ................................................. 7
» Model- Disc valve, roll-gerotor
» Wheel mount
» Side and rear ports
» Shafts- straight, splined and tapered
» Metric and BSPP ports
» Other special features
GENERAL
Max. Displacement,
3
3
397 [24.2]
cm /rev [in /rev]
Max. Speed,
560
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
Max. Oil Flow,
cont.: 90 [7965]
24 [32.2]
cont.: 200 [2900]
bar [PSI]
5
[RPM]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Pressure fluid
O
Temperature range,
-40÷140 [-40÷284]
O
C [ F]
20÷75 [98÷347]
2
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Oil flow in drain line
Oil flow in
Pressure drop Viscosity
drain line
2
bar [PSI]
mm /s [ SUS] lpm [GPM ]
140 [2030]
210 [ 3045]
int: 225 [3270]
90 [24]
lpm [GPM]
Min. Speed,
int: 110 [9735]
20 [ 98 ]
1,5 [ .396 ]
35 [ 164 ]
1 [ .264 ]
20 [98]
3 [ .793 ]
35 [164]
2 [ .528 ]
p
p
bar
PSI
14
12
10
8
6
4
200
Pressure Losses
150
100
50
2
0
0
4
0
2.5
5
0
10
20
7.5
30
10
40
12.5
50
15
60
17.5
70
20
22.5 Q, GPM
80
90 Q, lpm
MSWM
EPMS
MOTORS
MOTORS
SPECIFICATION DATA
MSWM
160
Type
Displacement, cm3/rev [in3/rev]
MSWM
200
159,7 [ 9.74 ] 200 [12.2]
MSWM
250
MSWM
315
MSWM
400
250 [15.3] 19.2 [314,9] 397 [24.2]
Max. Speed,
cont.
470
375
300
240
185
[RPM]
Int.*
560
450
360
285
225
Max. Torque
cont.
46 [ 4070 ]
daNm [lb-in]
Int.*
51,5 [4560 ] 64,5 [5710] 80,6 [7135] 96,0 [8500] 97,0 [8585]
peak**
51,5 [4560 ]
Max. Output
cont.
18,6 [24.9 ] 18,1 [24.3] 18,0 [24.1] 17,0 [22.8] 11,0 [14.7]
kW [HP]
int.*
24,0 [32.2] 24,0 [32.2] 23,8 [31.9] 20,2 [27.1]
Max. Pressure Drop
cont.
200 [2900] 200 [2900] 200 [2900] 200 [2900] 160 [2320]
bar [PSI]
Int.*
225 [3270] 225 [3270] 225 [3270] 220 [319 0] 175 [2540]
peak**
225 [3270] 225 [3270] 225 [3270] 225 [3270] 200 [2900]
56,6 [5010] 70,8 [6270] 90,0 [7965] 90,0 [7965]
65 [5755] 80,6 [7135] 108 [9560] 110 [9735]
12 [16.1]
Max. Oil Flow
cont.
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
lpm [GPM]
Int.*
90 [24]
90 [24]
90 [24]
90 [24]
90 [24]
Max. Inlet Pressure
cont.
210 [3045] 210 [3045] 210 [3045] 210 [3045] 210 [3045]
bar [PSI]
Int.*
250 [3625] 250 [3625] 250 [3625] 250 [3625] 250 [3625]
peak**
300 [4350] 300 [4350] 300 [4350] 300 [4350] 300 [4350]
Max. Return Pressure
cont.
140 [2030] 140 [2030] 140 [2030] 140 [2030] 140 [2030]
with Drain Line
Int.*
175 [2540] 175 [2540] 175 [2540] 175 [2540] 175 [2540]
bar [PSI]
peak**
210 [3045] 210 [3045] 210 [3045] 210 [3045] 210 [3045]
Max. Starting Pressure with Unloaded Shaft, bar [PSI]
Min. Starting Torque daNm [lb-in]
Min. Speed***, [RPM]
10 [14 5]
10 [14 5]
10 [14 5]
10 [14 5]
10 [14 5]
36,9 [3270 ] 46,2 [4090] 58,0 [5135] 73,8 [6530] 72,0 [6370]
6
6
6
5
5
* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
2
4. Recommended minimum oil viscosity 13 mm /s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
5
MSWM
EPMS
MOTORS
MOTORS
DIMENSIONS AND MOUNTING DATA
max 128 [5.039]
max L
max 96,5 [3.8] for M shaft
54
[2.126]
9
[.354]
16±0,3
[.63±.0118]
21±0,3
[.827±.0118]
102
[4.016]
max 139
[5.47]
0
T
44
[1.732]
C
22±0,3
[.866±.0118]
5±0,15
[.197±.0059]
41
[1.614]
L2
ø160±0,2
[6.299±.0078]
27±0,3
[1.063±.0118]
E Rear Ports
C: 2xM10-12 mm [.47 in] depth
P(A,B): 2xG1/2 or 2xM22x1,5-15 mm [.59 in] depth
T: G ¼ or M14x1,5- 12 mm [.47 in] depth (plugged)
Type
53
[2.086]
max 139
[5.47]
P(A,B)
53
[2.086]
32±0,3
[1.26±.0118]
ø125 -0,063
[4.921-.0025 ]
ø85
[3.346
16
P(A,B)
16±0,3
[.63±.0118]
21±0,3
[.827±.0118]
L1
4xø13,5
[.531]
L, mm [in] L2, mm [in] L1, mm [in]
MSWM 160 170,5 [6.71]
129,3 [5.09] 27,8 [1.09]
MSWME 160 177,5 [6.99]
Port B
MSWM 200 177,5 [6.99]
136,3 [5.37] 34,8 [1.37]
MSWME 200 184,5 [7.26]
Port A
32±0,3
[1.26±.0118]
MSWM 250 186,0 [7.32]
145,0 [5.71] 43,5 [1.71]
MSWME 250 193,0 [7.60]
MSWM 315 197,5 [7.78]
157,3 [6.19] 54,8 [2.16]
MSWME 315 206,5 [8.13]
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
MSWM 400 212,0 [8.35]
171,0 [6.73] 69,4 [2.73]
MSWME 400 219,0 [8.62]
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
PERMISSIBLE SHAFT LOADS
The output shaft runs in tapered bearings that permit high axial and radial forces.
Curve "1" shows max. radial shaft load at bearing life of 2000 hours at 100 RPM.
Curve "2" shows max. radial shaft load at bearing life of 3000 hours at 200 RPM.
Pr
daN
8000
-.5
0
.5
1
1.5
2
2.5
3
3.5
4
4.5
in
5
Pr
lbs
18000
7000
16000
6000
14000
12000
5000
1
10000
2
8000
4000
3000
6000
2000
4000
1000
0
-20
2000
-10
0
10
20
30
40
50
60
6
70
80
90
100 110 120 mm
mm [in]
MSWM
EPMS
MOTORS
MOTORS
SHAFT EXTENSIONS
C -ø40 straight, Parallel key A12x8x70 DIN 6885
K -tapered 1:10, Parallel key B12x8x28 DIN 6885
Max. Torque 132,8 daNm [11755 ln-in]
Max. Torque 210,7 daNm [18650 lb-in]
A-A
12 -0.043
A
Taper 1:10
CO-ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46
ø56
[2.205]
9
[.354]
82 -0,2
[3.228-.0079]
M12
min 25 [.984] deep
[1.5 -.001 ]
ø45
[1.771]
[1.5 -.0019]
ø38,1 -0,05
56 +2
[2.205 +.079 ]
ø38,1 -0,025
45 0
Max. Torque 132,8 daNm [11755 ln-in]
45 0
ø45
[1.771]
54±0,4
4
[2.126±.016]
[.157]
82±0,2
[3.228±.0079]
SH -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976
Max. Torque 132,8 daNm [11755 ln-in]
42,4 -0,2
[1.669-.0079 ]
M30x2
ø6,3
[.248]
82 -0,2
[3.228-.0079]
3/8-16 UNC
min 25 [.984] deep
S=46
Tightening torque
50±3 daNm
[4425±265 lb-in]
ø45
[1.771]
24,15 -0,2
[.95 -.0079]
+0,018
ø40 +0,002
M12
min 25 [.984] deep
9.545 -0,02
[.379-.0008]
A
[.472-.0017 ]
0
[1.575+.0007
+.0001 ]
45
ø45
[1.771]
43 -0,2
[1.692 -.0079]
[.472-.0017 ]
12 -0.043
82 -0,2
[3.228-.0079]
M -ø1½" splined 17T, DP 12/24 ANSI B92.1-1976
Max. Torque 132,8 daNm [11755 ln-in]
[1.5 -.001 ]
ø45
[1.771]
ø38,1 -0,025
45 0
min 34
[1.34]
52 -0,2
[2.047-.0079]
M12
min 25 [.984] deep
mm [in]
ORDER CODE
1
2
3
4
5
6
MSWM
Pos.1 - Port type
omit - Side ports
E
Pos. 4 - Ports
omit
M
- Rear ports
Pos.2 - Displacement code
160
200
250
315
400
- BSPP (ISO 228)
- Metric (ISO 262)
Pos. 5 - Special Features (see page 48)
- 159,7 cm3/rev [9.74 in3/rev]
- 200,0 cm3/rev [12.20 in3/rev]
- 250,0 cm3/rev [15.30 in3/rev]
- 314,9 cm3/rev [19.20 in3/rev]
- 397,0 cm3/rev [24.20 in3/rev]
Pos. 6 - Design Series
omit - Factory specified
Pos.4 - Shaft Extensions*
NOTES:
* The permissible output torque for shafts must
not be exceeded!
- ø40 straight, Parallel key A12x8x70 DIN6885
C
3
3
CO - ø1½ ” straight, Parallel key /8”x /8”x2¼” BS46
The hydraulic motors are mangano-phosphatized
as standard.
- ø45 tapered 1:10, Parallel key B12x8x28 DIN6885
K
SH - ø1½" splined 17T ANS B92.1-1976
- ø1½" splined 17T ANS B92.1-1976
M
7
HYDRAULIC MOTORS MTK
APPLICATION
A
A
B
B
» Conveyors
» Metal working machines
» Machines for agriculture
» Road building machines
» Mining machinery
» Food industries
» Special vehicles
» Plastic and rubber machinery etc.
CONTENTS
OPTIONS
Specification data ....................................... 9
Dimensions and mounting ................... 10÷13
Shaft extensions ...................................... 14
Permissible shaft loads ............................ 15
Order code ................................................. 16
» Model- Disc valve, roll-gerotor
» Flange mount with wheel mount
» Side and rear ports
» Shafts- straight, splined and tapered
» Metric, SAE and BSPP ports
» Other special features
GENERAL
cm3/rev [in3/rev]
Displacement,
157,9÷502,4 [9.63÷30.7]
RPM
Max. Speed,
159÷505
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
22 [30]
Max. Pressure Drop,
bar [PSI]
160÷250 [2320÷3626]
57÷109 [5045÷9650]
lpm [GPM]
Max. Oil Flow,
80 [21]
RPM
Min. Speed,
5÷10
daN [lb]
Permissible Shaft Loads,
Pa=1000 [2250]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Pressure fluid
O
Temperature range,
O
C [ F]
-30÷90 [-22÷194]
2
20÷75 [98÷347]
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Oil flow in drain line
Oil flow in
Pressure drop Viscosity
drain line
2
bar [PSI]
mm /s [ SUS] lpm [ GPM ]
100 [ 1450]
140 [ 2030]
20 [ 98 ]
2,5 [ .660 ]
35 [ 164 ]
1,8 [ .476 ]
20 [98]
3,5 [ .925 ]
35 [164]
2,8 [ .740 ]
p
p
bar
PSI
14
12
10
8
6
4
200
Pressure Losses
150
100
50
2
0
0
0
0
8
2
10
4
6
8
20
30
10 12 14 16 18 20 22 24 26
40
50
60
70
80
90
100
Q, GPM
Q, lpm
MTK
EPMS
MOTORS
MOTORS
SPECIFICATION DATA
Type
Displacement,
3
3
cm /rev [in /rev]
MTK
160
MTK
200
MTK
250
MTK
315
MTK
400
MTK
470
MTK
500
157,9
201,3
252,2
314,9
396,8
470,5
502,4
[9.63]
[12.28]
[15.38]
[19.2]
[24.2]
[28.7]
[30.65]
Max. Speed,
Cont.
505
400
320
255
200
170
159
[RPM]
Int.*
630
500
400
315
250
210
199
Max. Torque,
Cont.
57 [5045]
72 [6373]
daNm [lb-in]
Int.*
Max. Output,
Cont.
22 [29.5]
22 [29.5]
21 [28.2]
kW [HP]
Int.*
27 [36.2]
27 [36.2]
25 [33.5] 23,5 [31.5]
Max. Pressure Drop,
Cont.
250 [3626] 250 [3626] 250 [3626] 250 [3626] 200 [2900] 160 [2320] 160 [2320]
bar [PSI]
Int.*
325 [4714] 325 [4714] 300 [4350] 300 [4350] 250 [3626] 200 [2900] 200 [2900]
Max. Inlet Pressure,
Cont.
250 [3626]
bar [PSI]
Int.*
350 [5077]
Max. Oil Flow,
Cont.
80 [21.1]
lpm [GPM]
Int.*
100 [26.4]
91 [8055] 105 [9293] 107 [9470] 102 [9028] 109 [9648]
72,5 [6420] 92 [8143] 107 [9470] 131 [11595] 140 [12390] 133 [11772] 136 [12037]
20 [26.8]
17,5 [23.5]
14 [18.8]
14 [18.8]
22 [29.5]
17.5 [23.5]
17 [22.8]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI]
8 [116]
8 [116]
7 [102]
7 [102]
7 [102]
7 [102]
7 [102]
43 [3806]
54 [4780]
68 [6020]
79 [6992]
80 [7080]
83 [7346]
84 [7435]
at max. pressure
Min. Starting Torque,
drop cont.
daNm [lb-in]
at max. pressure
drop int.*
54.5 [4824] 69 [6107]
Max. Return Pressure without Drain Line,
80 [7080] 98,5 [8720] 105 [9294] 105 [9294] 105 [9294]
see
bar [PSI]
diagram
Max. Return Pressure
Cont.
140 [2030]
with Drain Line,
Int.*
175 [2540]
bar [PSI]
Peak*
210 [3046]
Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
*
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 70 SUS [13 cmі/s] at 122°F [50°C].
5. Recommended maximum system operating temperature is 180°F [82°C].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
9
MTK
EPMS
MOTORS
MOTORS
DIMENSIONS - MTK W and MTK C
R Shaft CO Shaft SB Shaft
Shaft Dim.
See Page 14
73,8 [2.91]
84 [3.31]
12,4 [.488]
114,3 [4.499]
102,5 [4.04]
96,8 [3.81]
6,4
[.252]
L1
L2
LS
L3
L3
LS
L2
L1
6,4
[.252]
18,4 [.73]
18
[.7]
99,5 [3.92]
124,5 [4.9]
46,5 [1.83]
R Shaft CO Shaft SB Shaft
62 [2.44]
K Shaft
T Shaft
59 [2.32]
K Shaft
56,3 [2.22]
T Shaft
L4
L4
T
T
B
B
A
A
7
[.27]
24.5
[.965]
P(A,B)
17,5
[.69]
7
[.28]
24.5
[.965]
24.5
[.96]
90 [3.54]
24.5
[.96]
(90 [3.54])
(115 [4.528] Dia.)
115 [4.53] Dia.
126,9±0,07 [4.996±.0028]
Port A
P(A,B)
17,5
[.69]
Flange Dim.
See Page 13
Port A
Rear Ports Dim.
See Page 12
Port B
Port B
Versions
Rear
Side
65 [2.56]
2
5
1
6
7
P (A,B) 2xG 3/4 2xM27x2 2x1 / 16-12UN 2xG 1/2 2x / 8 -20UNF
7
T
/ 16 -20UNF
G 1/4 M14x1,5 7/ 16 -20UNF
G 1/4
(122,5 [4.82])
mm [in]
4
3
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
Type
MTKW160 MTKC160
MTKW200 MTKC200
MTKW250 MTKC250
MTKW315 MTKC315
MTKW400 MTKC400
MTKW470 MTKC470
MTKW500 MTKC500
LS, mm [in]
21,8 [.86]
27,8 [1.09]
34,8 [1.37]
43,5 [1.71]
54,8 [2.16]
65,0 [2.56]
69,4 [2.73]
Type
Type
L1, mm [in] L2, mm [in] L3, mm [in] L4, mm [in]
L1, mm [in] L2, mm [in] L3, mm [in] L4, mm [in]
MTKW160 110,8 [4.36] 120,3 [4.74] 139,3 [5.48] 162,2 [6.39] MTKC160 151,3 [5.96] 160,8 [6.33] 179,8 [7.08] 202,7 [7.98]
MTKW200 116,8 [4.59] 126,3 [4.97] 145,3 [5.72] 168,2 [6.62] MTKC200 157,3 [6.19] 166,8 [6.57] 185,8 [7.32] 208,7 [8.22]
MTKW250 123,8 [4.87] 133,3 [5.25] 152,3 [5.99] 175,2 [6.89] MTKC250 164,3 [6.47] 173,8 [6.84] 192,8 [7.59] 215.7 [8.49]
MTKW315 132,5 [5.22] 142,0 [5.59] 161,0 [6.34] 183,9 [7.24] MTKC315 173,0 [6.81] 182,5 [7.19] 201,5 [7.93] 224,4 [8.84]
MTKW400 143,8 [5.66] 153,3 [6.04] 172,3 [6.78] 195,2 [7.69] MTKC400 184,3 [7.26] 193,8 [7.63] 212,8 [8.38] 235,7 [9.28]
MTKW470 154,0 [6.06] 163,5 [6.44] 182,5 [7.19] 205,4 [8.09] MTKC470 194,5 [7.66] 204,0 [8.03] 223,0 [8.78] 245,9 [9.68]
MTKW500 158,4 [6.24] 167,9 [6.61] 186,9 [7.36] 209,8 [8.26] MTKC500 198,9 [7.83] 208,4 [8.20] 227,4 [8.95] 250,3 [9.85]
10
MTK
EPMS
MOTORS
MOTORS
DIMENSIONS - MTK F
SB Shaft
6 [.24]
Shaft Dim.
See Page 14
62 [2.44]
59 [2.32]
R Shaft CO Shaft
56,3 [2.22]
T Shaft
LS
L4
L3
L2
L1
15.5 [.61]
84 [3.31]
73,8 [2.91]
K Shaft
T
B
A
Flange Dim.
See Page 13
P(A,B)
7
[.28]
24.5
[.96]
17,5
[.69]
24.5
[.96]
Rear Ports Dim.
See Page 12
(90 [3.54])
115 [4.53] Dia.
mm [in]
Port A
Port B
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Versions
2
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
Type
MTKF 160
MTKF 200
MTKF 250
MTKF 315
MTKF 400
MTKF 470
MTKF 500
Rear
Side
4
3
1
5
6
2xG 3/4 2xM27x2 2x1 / 16-12UN 2xG 1/2 2x 7/ 8 -20UNF
7
/ 16 -20UNF
G 1/4 M14x1,5 7/ 16 -20UNF
G 1/4
P (A,B)
T
L1, mm [in]
L2, mm [in]
L3, mm [in]
L4, mm [in]
LS, mm [in]
151,3 [5.96]
157,3 [6.19]
164,3 [6.47]
173,0 [6.81]
184,3 [7.26]
194,5 [7.66]
198,9 [7.83]
160,8 [6.33]
166,8 [6.57]
173,8 [6.84]
182,5 [7.19]
193,8 [7.63]
204,0 [8.03]
208,4 [8.21]
179,8 [7.08]
185,8 [7.32]
192,8 [7.59]
201,5 [7.93]
212,8 [8.38]
223,0 [8.78]
227,4 [8.95]
202,7 [7.98]
208,7 [8.22]
215,7 [8.49]
224,4 [8.84]
235,7 [9.28]
245,9 [9.68]
250,3 [9.85]
21,8 [.86]
27,8 [1.09]
34,8 [1.37]
43,5 [1.71]
54,8 [2.16]
65,0 [2.56]
69,4 [2.73]
11
MTK
EPMS
MOTORS
MOTORS
Rear Ports
23 [.91]
MTK W
21,8 [.86]
B
5,6 [.22]
A
13,8
[.54]
19,5
[.77]
L4+14 [.55]
24,4
[.96]
23 [.91]
MTK C
21,8 [.86]
B
5,6 [.22]
A
L4+14 [.55]
13,8
[.54]
19,5 24,4
[.77] [.96]
23 [.91]
MTK F
21,8 [.86]
B
5,6 [.22]
A
L4+14 [.55]
13,8
[.54]
19,5
[.77]
24,4
[.96]
mm [in]
12
MTK
EPMS
MOTORS
MOTORS
DIMENSIONS OF MOUNTING
W 4-Bolt flange, Wheel Motor
spigot diameter 107,9 mm [2.25 in] - BC 147,6 mm [5.81 in]
L5
+.0019
ø107,9 -0,09
1-20 UNEF
[4.25 -.0035 ] Dia.
Type
L5, mm [in]
MTKW...CO... 99,5 [3.92]
MTKW...SB... 96,8 [3.81]
MTKW...R... 102,5 [4.04]
MTKW...K... 114,3 [4.49]
MTKW...T... 124,5 [4.91]
ø147,6
[5.81] Dia.
(133 [5.24])
C 4-Bolt flange,
spigot diameter 127 mm [4.99 in] - BC 161,92 mm [6.375 in]
12,4
[.49]
Type
MTKC...CO...
MTKC...SB...
MTKC...R...
MTKC...K...
MTKC...T...
0
ø127-0,12
L5, mm [in]
59 [2.39]
56,3 [2.22]
62,0 [2.44]
73,8 [2.91]
84,0 [3.31]
0
18,4
[.72]
4x ø14,3
[.56] Dia.
(145 [5.71])
mm [in]
L5
[4.99-.0047 ] Dia.
6,4
[.25]
46,5
[1.83]
(133 [5.24])
4x ø13,6
[.535] Dia.
18
[.71]
+0,05
6,4
[.25]
(145 [5.71])
ø161,92 [6.375] Dia.
F 6-Bolt flange,
spigot diameter 82,5 mm [3.25 in] - BC 106,35 mm [4.19 in]
L5
15,5
[.61]
6
[.24]
L5, mm [in]
59 [2.39]
56,3 [2.22]
62,0 [2.44]
73,8 [2.91]
84,0 [3.31]
22,5o
ø106,35
[4.19] Dia.
137 [5.39] max.
13
+.0016
Type
MTKF...CO...
MTKF...SB...
MTKF...R...
MTKF...K...
MTKF...T...
[3.25- .0032 ] Dia.
+0,04
ø82,5 - 0,08
6x ø13,5
[.53] Dia.
MTK
EPMS
MOTORS
MOTORS
SHAFT EXTENSIONS
CO
R
ø1.25” [31,75] srtaight, Parallel key 16 "x 16 "x 1 ¼"
Max. Torque 77 daNm [6815 lb-in]
5
ø1.25” [31,75] tapered 1:8, Parallel key 5 16"x 5 16 "x3 4"
Max. Torque 77 daNm [6815 lb-in]
5
3,918±0,1
[.154±.0039]
(3,91 [.154])
19,05±0,2
[.749±.0079]
12,7 [.499]
ø45 [1.77] Dia.
2xø4
[.157]
7,95±0,01
[.32±.00039]
5
[.197]
21 min
[.827]
Max. Torque 20±1 daNm
[1770±88.5 lb-in]
51,5±0,2
[2.028±.0079]
R0,8 [.03]
4,5 -0,3
[.177-.0118 ]
35±0,6
[.049±.024]
53,5±0,3
[2.106±.0118]
SB
ø31,75±0,025
[1.25±.00098] Dia.
1-20UNEF-2A
+0,33
ø31,75 -0,025
[1.25-.00098]
Dia.
35 -0,17
.0129
[.049 +-.0067
]
7,95±0,01
[.32±.00039]
R0,8 [.03]
ø45 [1.77] Dia.
3/8-16UNC
+0,05
31,7 -0,33
[1.25 +.0019
-.0129 ]
55±0,3
[2.165±.0118]
3/8-16UNC
ø1.25” [31,75] 14T Splined ANSI B92.1-1970, 12/24
Max. Torque 77 daNm [6815 lb-in]
K
+0,4
12,7 [.499]
9,53±0,15
[.375±.0059]
Max. Torque 20±1 daNm
[1770±88.5 lb-in]
T
ø1.625” [41,275] tapered 1:8, Parallel key 16 "x
Max. Torque 100 daNm [8850 lb-in]
16
"x1 4 "
1
47,5±0,6
[1.87±.024]
+0,4
31,7 -0,2
[1.25 +.0157
-.0079 ]
15,7
[.618]
R0,8 [.03]
ø45 [1.77] Dia.
2xø4 [.157]
+0,03
11,11
4 [.157]
67-0,3 [2,64 -.0129 ]
R0,8
[.03]
Max. Torque 50±1 daNm
[4425±88.5 lb-in]
4 [.157]
54±0,6
[2.126±.0236]
75,5±0,3
[2.97±.0118]
77±0,3
[3.03±.0118]
14
ø41,275±0,025
[1.625±.00098] Dia.
11/418UNEF-2A
+0,07
7
(5,56 [.219])
[.437+.00118]
R0,8 [.03]
66±0,3 [2.59±.0118]
7
[.219 +.0028
-.0079 ]
ø45 [1.77] Dia.
49±0,2
[1.93±.0079]
5,57 -0,20
R0,8 [.03]
ø38,1 [1.49] Dia.
24,5±0,2
[1±.0079]
(4,53 [.178])
2xø4
[.157]
R0,8
[.03]
[1 +.0157
-.0078 ]
1-20UNEF
21 min
[.827]
ø25,4±0,1
[1±.0039] Dia.
5 [.197]
[.179 +.0065
-.0014 ]
25,4 -0,2
4,539 +0,165
-0,035
ø31,75 -0,025
[1.25-.00098]
Dia.
ø45 [1.77] Dia.
ø1.5” [38,1] tapered 1:8, Parallel key 3 8 "x 3 8 "x1"
Max. Torque 89 daNm [7878 lb-in]
mm [in]
MTK
EPMS
MOTORS
MOTORS
PERMISSIBLE SHAFT LOADS
The curves apply to a B10 bearing life (ISO281) of 2000 hours at 1 00 RPM.
MTKF
Prad (lbs)
Prad (daN)
14000
6000
5596
12000
5000
10000
4000
8000
3000
6000
2000
4000
1000
mm
0
90 80 70 60 50 40 30 20 10
in
2000
-4
-3
-2
-1
0
0 -10 -20 -30 -40 -50 -60 -70
0
2
1
3
56,3 [2.22]
59 [2.32]
62 [2.44]
73,8 [2.9]
84 [3.31]
The curves apply to a B10 bearing life (ISO281) of 2000 hours at 100 RPM.
MTKC
MTKW
Prad (daN)
Prad (lbs)
Prad (lbs)
Prad (daN)
14000
6000
6000
5596
14000
5596
12000
12000
5000
5000
10000
10000
4000
4000
8000
8000
3000
3000
6000
6000
2000
2000
4000
1000
mm
0
90 80 70 60 50 40 30 20 10
in
4000
1000
2000
mm
0
131,5
0 -10 -20 -30 -40 -50 -60 -70
0
130 120 110 100 90 80 70 60 50 40 30 20 10
0 -10 -20 -30 -40
in
-4
-3
-2
-1
0
1
2
3
-5
-4
-3
-2
-1
96,8 [3.81]
56,3 [2.22]
99,5 [3.92]
59 [2.32]
102,5 [4.04]
62 [2.44]
114,3 [4.5]
73,8 [2.9]
124,5 [4.9]
84 [3.31]
15
0
1
2000
0
MTK
EPMS
MOTORS
MOTORS
MAX. PERMISSIBLE SHAFT SEAL PRESSURE for MTK motors
Max. return pressure without drain line or
max. pressure in the drain line
P
bar
P
PSI
1800
120
1600
1450
1400
100
1200
1090
1000
80
60
800
600
40
- continuous operations
- intermittent operations
400
20
200
0
0
0
100
200
300
400
500
600
700
800
min-1
ORDER CODE
1
2
3
4
5
6
7
8
MTK
Pos.1 - Mounting Flange
W
- 4-Bolt flange, Wheel Motor spigot diameter 107,9 mm
Pos.4 - Shaft Extensions*
CO
[2.25 in] - BC 147,6 mm [5.81 in]
C
SB
- 4-Bolt flange, spigot diameter 127 mm [4.99 in] BC 161,92 mm [6.375 in]
F
R
- Bolt flange, spigot diameter 82,5 mm [3.25 in] BC 106,35 mm [4.19 in]
K
Pos.2 - Port type
- ø1.25" [31,75] straight,
Parallel key 5/16"x5/16"x1 1/4", 3/8-16 UNC
- ø1.25" [31,75] 14T Splined ANSI B92.1-1970,
12/24, 3/8-16 UNC
- ø1.25" [31,75] Tapered 1:8,
Parallel key 5/16"x5/16"x3/4", 1-20 UNEF
- ø1.5" [38,1] Tapered 1:8,
Parallel key 3/8"x3/8"x1", 1-20 UNEF
- ø1.625" [41,275] Tapered 1:8,
Parallel key 7/16"x7/16"x1 1/4", 1 1/4-18 UNEF
omit - Side ports
E
- Rear ports
T
Pos.3 - Displacement code
Pos.5 - Port Size/Type
160
200
250
315
400
470
500
2
3
4
5
6
- 157,9 cm3/rev [ 9.63 in3/rev]
- 201,3 cm3/rev [12.28 in3/rev]
- 252,2 cm3/rev [15.38 in3/rev]
- 314,9 cm3/rev [19.20 in3/rev]
- 396,8 cm3/rev [24.20 in3/rev]
- 470,5 cm3/rev [28.70 in3/rev]
- 502,4 cm3/rev [30.65 in3/rev]
- side ports, 2xG 3/4, G1/4 BSP (ISO 228)
- side ports, 2xM27x2, M14x1,5 - 6H (ISO 262)
- side ports, 2x1 1/16-12 UN, 7/16-20 UNF
- rear ports, 2xG 1/2, G1/4 BSP (ISO 228)
- rear ports, 2x7/8-20 UNF, 7/16-20 UNF
Pos.6 - Check Valves
omit - without check valves
1
- with check valves
Pos.7 - Special Features (see page 48)
omit - Factory specified
Pos.8 - Design Series
omit - Factory specified
Notes: * The permissible output torque for shafts must be not exceeded!
** Color at customer's request.
The hydraulic motors are mangano phosphatized as standard.
16
HYDRAULIC MOTORS MTM
APPLICATION
» Skid Steer Loaders
» Metal working machines
» Trenchers
» Augers
» Agriculture machines
» Road building machines
» Special vehicles
» Mine machines
» Woodworking and sawmill machinery
» Conveyors etc.
A
A
B
B
OPTIONS
» Model- Disc valve, roll-gerotor
» Flange with wheel mount
» Short motor
» Side ports
» Shafts- straight, splined and tapered
» BSPP ports;
» Other special features.
CONTENTS
Specification data ......................................... 18
Function diagrams ................................. 19÷21
Dimensions and mounting ...................... 22÷24
Shaft extensions ............................................ 25
Permissible shaft loads .................................. 25
Dimensions and mounting- MTMV ................. 26
Dimensions and mounting- MTM6V ............... 27
Internal Spline data ....................................... 28
Order code ................................................... 28
EXCELLENCE
» High torque and pressure drop
» High inlet pressure
» High starting torque
» Improved efficiency at high pressure drop
» Smooth operation at low speed
GENERAL
Max. Displacement,
cm3/rev [in3/rev]
Max. Speed,
724,3 [44.2]
750
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
cont.: 183 [16200]
70 [94]
cont.: 250 [3600]
5
[RPM]
Permissible Shaft Loads
Pa=1000 [2250]
daN [lbs]
Pressure fluid
int.: 350 [5080]
150 [40]
lpm [GPM]
Min. Speed,
int.: 229 [20270]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
O
Temperature range,
O
C [ F]
-40÷140 [-40÷284]
2
20÷75 [98÷347]
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Pressure Losses
Oil flow in drain line
flow in
Pressure drop Viscosity Oil
drain
line
bar [PSI]
mm 2/s [ SUS] lpm [GPM ]
2,5 [.660 ]
20 [98]
200 [2 90 0]
2 75 [3990]
350
25
300
20
250
200
150
35 [164]
1,5 [ .400]
100
20 [98]
4 [1.057]
50
35 [164]
2,5 [.660]
15
10
5
0
0
0
0
17
25
5
75
50
10
15
20
100
25
125 Q, lpm
30
Q, GPM
MTM
MOTORS
SPECIFICATION DATA
Type
Displacement,
3
3
cm /rev [in /rev]
MTM
200
MTM
250
MTM
315
MTM
400
MTM
470
MTM
500
MTM
630
MTM
725
201,4
251,8
326,3
410,9
475
523,6
631,2
724
[12.29]
[15.36]
[19.9]
[25.06]
[28.97]
[31.95]
[38.52]
[44.2]
Max. Speed,
Cont.
625
500
380
305
260
240
190
170
[RPM]
Int.*
750
600
460
365
315
285
230
215
Max. Torque
Cont.
72[6375] 90[7965] 116[10265] 147[13010] 171[15135] 172[15225] 183[16200] 160[14160]
daNm [lb-in]
Int.*
102[9030] 128[11330] 163[14425] 206[18232] 215[16030] 215[16030] 229[20270] 192[17000]
Peak**
115[10180] 144[12745] 186[16460] 235[20800] 240[21240] 240[21240] 274[24250] 240[21240]
Max. Output
Cont.
41 [55]
41 [55]
41 [55]
41 [55]
41 [55]
37,5[50]
28 [37,5]
26 [35]
kW [HP]
Int.*
70 [94]
70 [94]
70 [94]
70 [94]
55 [74]
51 [68]
42 [56]
40 [54]
Max. Pressure Drop
Cont.
250[3600] 250[3600] 250[3600] 250[3600] 250[3600] 230[3340] 200[2900] 160[2320]
bar [PSI]
Int.*
350[5080] 350[5080] 350[5080] 350[5080] 315[4570] 280[4060] 250[3625] 210[3045]
Peak**
400[5800] 400[5800] 400[5800] 400[5800] 350[5080] 320[4640] 300[4350] 260[3770]
Max. Oil Flow
Cont.
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
lpm [GPM]
Int.*
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
Max. Inlet Pressure
Cont.
270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]
bar [PSI]
Int.*
370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]
Peak**
420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]
Max. Return Pressure
Cont.
without Drain Line or
Cont. 100-300 RPM 40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
Max. Pressure
Cont.
20 [290]
20 [290]
20 [290]
20 [290]
-
-
-
in Drain Line, bar [PSI]
Int.*
0-100 RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]
>300 RPM 20 [290]
75 [1100] 75 [1100] 75 [1100] 75 [1100]
0-max. RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]
75 [1100] 75 [1100] 75 [1100] 75 [1100]
Max. Return Pressure
Cont.
270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920] 270 [3920]
with Drain Line
Int.*
370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370] 370 [5370]
bar [PSI]
Peak**
420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100] 420 [6100]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI]
Min. Starting Torque daNm [lb-in]
Min. Speed***, [RPM]
Weight, kg [lb]
6 [90]
6 [90]
60[5310] 75[6640]
5
5
6 [90]
6 [90]
6 [90]
6 [90]
6 [90]
6 [90]
97[8585] 122[10800] 142[12570] 143[12655] 145[12830] 148[13100]
5
5
5
5
5
5
MTM
26,9 [59.3] 27,3 [60.2] 28,1 [62]
MTMW
27,4 [60.4] 27,8 [61.3] 28,6 [63.1] 29,5 [65.1] 30,2 [66.6] 30,7 [67.7] 30,2 [66.6] 31,5 [69.5]
MTMV
15,7 [34.6] 16,1 [35.5] 16,9 [37.3] 17,8 [39.3] 18,5 [40.8] 19 [41.9] 18,5 [40.8] 19,8 [43.7]
29 [64]
29,7 [65.5] 30,2 [66.6] 29,7 [65.5] 31 [68.4]
Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
*
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 70 SUS [13 mm²/s] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
18
MTM
MOTORS
FUNCTION DIAGRAMS
12000
150 l/min
39.6 GPM
33 GPM
125 l/min
100 l/min
26.4 GPM
80 l/min
21.2 GPM
60 l/min
40 l/min
10.6 GPM
20 l/min
15.85 GPM
140
5.3 GPM
M
M
lb-in daNm
2.65 GPM
Q=10 l/min
MTM 250
p=350 bar
5075 PSI
325 bar
4715 PSI
300 bar
4350 PSI
275 bar
3990 PSI
250 bar
3625 PSI
225 bar
3265 PSI
200 bar
2900 PSI
120
60 kW
50 kW
100
int.
10000
40 kW
8000
80
60
4000
cont.
20 kW
6000
30 kW
10 kW
40
160 bar
2320 PSI
85%
=86%
83%
t
2000
0
120 bar
1740 PSI
78%
5 kW
N=2,5 kW
20
80%
75%
70%
0
60%
cont.
50
0
100
150
200
250
350
300
400
80 bar
1160 PSI
40 bar
580 PSI
int.
450
500
550
n
-1
600 min (rpm)
14000
150
150 l/min
39.6 GPM
125 l/min
100 l/min
26.4 GPM
80 l/min
21.2 GPM
60 l/min
15.85 GPM
40 l/min
10.6 GPM
5.3 GPM
33 GPM
p=350 bar
5075 PSI
325 bar
4715 PSI
300 bar
4350 PSI
275 bar
3990 PSI
250 bar
3625 PSI
225 bar
3265 PSI
200 bar
2900 PSI
50 kW
int.
16000 175
20 l/min
M
M
lb-in daNm
2.65 GPM
Q=10 l/min
MTM 315
12000
125
40 kW
10000
75
cont.
100
8000
30 kW
6000
10 kW
5 kW
20 kW
=88%
160 bar
2320 PSI
t
50
87%
4000
2000
0
85%
83%
120 bar
1740 PSI
80%
75%
70%
60%
N=2,5 kW
25
80 bar
1160 PSI
40 bar
580 PSI
0
cont.
0
50
100
150
200
250
300
350
int.
400
n
450
The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI)
O
and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F].
19
500
min-1 (rpm)
MTM
MOTORS
FUNCTION DIAGRAMS
18000
200
16000
175
150 l/min
39.6 GPM
33 GPM
125 l/min
100 l/min
26.4 GPM
80 l/min
21.2 GPM
60 l/min
40 l/min
10.6 GPM
20 l/min
15.85 GPM
225
p=350 bar
5075 PSI
325 bar
4715 PSI
300 bar
4350 PSI
275 bar
3990 PSI
60 kW
int.
20000
5.3 GPM
M
M
lb-in daNm
2.65 GPM
Q=10 l/min
MTM 400
40 kW
14000
50 kW
30 kW
150
250 bar
3625 PSI
225 bar
3265 PSI
12000
100
cont.
125
10000
200 bar
2900 PSI
8000
=87%
6000
4000
20 kW
10 kW
t
75
160 bar
2320 PSI
5 kW
86% 85%
50
N=2,5 kW
2000
25
0
0
120 bar
1740 PSI
78%
83%
80%
80 bar
1160 PSI
75%
70%
60%
40 bar
580 PSI
cont.
0
100
50
200
150
250
int.
300
350
n
400
-1
min (rpm)
12000
125
100
8000
4000
150 l/min
39.6 GPM
33 GPM
125 l/min
100 l/min
26.4 GPM
30 kW
40 kW
150
10000
6000
p=350 bar
5075 PSI
325 bar
4715 PSI
300 bar
4350 PSI
275 bar
3990 PSI
250 bar
3625 PSI
225 bar
3265 PSI
200 bar
2900 PSI
50 kW
cont.
14000
80 l/min
175
21.2 GPM
16000
60 l/min
200
15.85 GPM
18000
40 l/min
225
10.6 GPM
20000
5.3 GPM
250
20 l/min
22000
2.65 GPM
M
daNm
int.
M
lb-in
Q=10 l/min
MTM 470
10 kW
20 kW
160 bar
2320 PSI
5 kW
75
=87%
t
50
2000
25
0
0
N=2,5 kW
85%
120 bar
1740 PSI
78%
83%
80%
80 bar
1160 PSI
70%
75%
40 bar
580 PSI
60%
cont.
0
50
100
150
200
int.
250
300
The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI)
O
and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F].
20
n
350
min-1 (rpm)
MTM
MOTORS
FUNCTION DIAGRAMS
14000
12000
150 l/min
39.6 GPM
33 GPM
125 l/min
100 l/min
26.4 GPM
80 l/min
21.2 GPM
60 l/min
175
15.85 GPM
16000
40 l/min
200
10.6 GPM
18000
20 l/min
225
5.3 GPM
20000
2.65 GPM
M
daNm
p=325 bar
4715 PSI
300 bar
4350 PSI
275 bar
3990 PSI
250 bar
3625 PSI
225 bar
3265 PSI
50 kW
40 kW
int.
M
lb-in
Q=10 l/min
MTM 500
150
20 kW
125
200 bar
2900 PSI
30 kW
10000
8000
6000
4000
75
160 bar
2320 PSI
10 kW
cont.
100
80%
83%
=86%
t
50
2000
25
0
0
78%
5 kW
N=2,5 kW
120 bar
1740 PSI
75%
80 bar
1160 PSI
70%
60%
cont.
0
50
100
150
40 bar
580 PSI
int.
200
250
n
300
-1
min (rpm)
16000
14000
150 l/min
200 bar
2900 PSI
150
10 kW
cont.
160 bar
2320 PSI
20 kW
100
85%
83%
78%
120 bar
1740 PSI
80%
75%
75
N=2,5 kW
4000
50
2000
25
0
0
225 bar
3265 PSI
40 kW
175
10000
39.6 GPM
33 GPM
125 l/min
100 l/min
26.4 GPM
80 l/min
30 kW
125
6000
21.2 GPM
250 bar
3625 PSI
12000
8000
60 l/min
200
15.85 GPM
18000
40 l/min
225
10.6 GPM
20000
5.3 GPM
250
20 l/min
22000
2.65 GPM
M
daNm
int.
M
lb-in
Q=10 l/min
MTM 630
5 kW
=87%
80 bar
1160 PSI
t
70%
40 bar
580 PSI
60%
cont.
0
25
50
75
100
125
150
175
int.
200
225
The function diagrams data was collected at back pressure 5÷10 bar (72.5PSI÷145PSI)
O
and oil with viscosity of 32 mm²/s [150SUS] at 50° C [122 F].
21
n
250
min-1 (rpm)
MTM
MOTORS
DIMENSIONS AND MOUNTING DATA - MTM and MTMC
82,5
[3.248]
[2.181]
55,4
Flange Dim.
See Page 24
SH Shaft
82
[3.228]
82
[3.228]
40...40,4
[1.575...1.59]
K Shaft C,CO Shaft
Shaft Dim.
See Page 25
82
[3.228]
SH Shaft
30,8...31,2
[1.212...1.228]
C,CO Shaft
82
[3.228]
K Shaft
T
L2
ø139
[5.472]
L1
ø139
[5.472]
L1
max L
max L
L2
T
21±0,15
[.827±.0059]
P(A,B)
P(A,B)
42±0,15
42±0,15
[1.653±.0059] [1.653±.0059]
Port A
T - Drain port
Port B
F
ø21 +0,4
[.827 +.0157 ]
12
[.472]
G1/4
F
1
[.0394]
139
[5.472]
72
[2.834]
Warning: Drain line should always be used.
P(A, B): 2xG3/4 - 17 mm [.669 in] depth
T : G1/4 - 12 mm [.472 in] depth (plugged)
Type
MTM 200
MTM 250
MTM 315
MTM 400
MTM 470
MTM 500
MTM 630
MTM 725
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
L, mm [in]
188 [7.40]
194 [7.64]
203 [7.99]
214 [8.43]
222 [8.74]
228 [8.98]
224 [8.82]
233 [9.17]
L2, mm [in]
142,3[5.60]
148,6 [5.85]
157,8 [6.21]
168,3 [6.63]
176,3 [6.94]
182,3 [7.18]
178,3 [7.02]
187,3 [7.37]
Type
MTMC 200
MTMC 250
MTMC 315
MTMC 400
MTMC 470
MTMC 500
MTMC 630
MTMC 725
L, mm [in] L2, mm [in]
198 [7.79] 153 [6.02]
204,5 [8.05] 159,3 [6.27]
213,5 [8.40] 168,5 [6.63]
224 [8.82] 179 [7.04]
232 [9.13] 187 [7.36]
238 [9.37] 193 [7.60]
234 [9.21] 189 [7.44]
243 [9.56] 198 [7.79]
L1, mm [in]
25 [.98]
31,3 [1.23]
40,5 [1.59]
51 [2.01]
59 [2.32]
65 [2.56]
61 [2.40]
70 [2.76]
mm [in]
22
MTM
MOTORS
DIMENSIONS AND MOUNTING DATA - MTMW
K Shaft
C, CO Shaft
SH Shaft
82
[3.228]
[3.905...3.929]
Flange Dim.
See Page 24
L1
ø139
[5.472]
Port Dim.
See Page 22
max L
L3
L2
99,2...99,8
82
[3.228]
Shaft Dim.
See Page 25
P(A,B)
Port A
Warning: Drain line should always be used.
P(A, B): 2xG3/4 - 17 mm [.669 in] depth
T : G1/4 - 12 mm [.472 in] depth (plugged)
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
T
Port B
Type
MTMW 200
MTMW 250
MTMW 315
MTMW 400
MTMW 470
MTMW 500
MTMW 630
MTMW 725
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
L, mm [in] L1, mm [in] L2, mm [in] L3, mm [in]
129 [5.08] 25 [.98] 83,8 [3.30] 111,1 [3.37]
135 [5.32] 31,3 [1.23] 90,1 [3.55] 117,4 [4.62]
144 [5.67] 40,5 [1.59] 99,3 [3.91] 126,6 [4.98]
155 [6.10] 51 [2.01] 109,8 [4.32] 137,1 [5.40]
163 [6.42] 59 [2.32] 117,8 [4.64] 145,1 [5.71]
169 [6.65] 65 [2.56] 123,8 [4.87] 151,1 [5.95]
165 [6.50] 61 [2.40] 119,8 [4.72] 147,1 [5.79]
174 [6.85] 70 [2.76] 128,8 [5.07] 156,1 [6.15]
mm [in]
23
MTM
MOTORS
MOUNTING
4-Bolt flange
spigot diameter ø160 mm [6.3 in] - BC ø200 [7.874 in] mm
ø160 -0,063
180
[7.086]
[6.299 -.0025]
40,2
[1.582]
9
[.354]
ø139
[5.472]
ø200±0,4
[7.874±.0157]
ø98±0,5
[3.858±.0197]
4xø18±0,15
[.708±.0059]
24
[.945]
C 4-Bolt flange
spigot diameter ø125 mm [4.921 in] - BC ø160 mm [6.3 in]
ø160±0,4
-.0004]
[4.921-.0019
147
[5.787]
-0,01
ø125 -0,05
9±0,5
[.354±.0197]
[6.3±.0157]
R16
[.63]
ø125 -0,1
[.551+.0039
+.0118 ]
[4.921-.0039]
+0,1
4xø14 +0,3
21±0,5
[.827±.0197]
W 4-Bolt flange, Wheel Motor
spigot diameter ø160 mm [6.3 in] - BC ø200 mm [7.874 in]
42
[1.653]
4
[.157]
24
21
[.827]
ø160 -0,063
ø172 -0,063
7
[.275]
[6.299 -.0025]
ø200±0,4
[7.874±.0157]
[6.772 -.0025]
180
[7.086]
4xø18±0,15
[.708±.0059]
mm [in]
MTM
MOTORS
SHAFT EXTENSIONS
C - ø40 straight, Parallel key A12x8x70 DIN 6885
SH - ø1½" splined 17T, DP 12/24 ANSI B92.1-1976
Max. Torque 132,8 daNm [11755 lb-in]
°
R2±0,2
[.0787±.0078]
ø38,1 -0,025
[1.5 -.001 ]
ø50
[1.968]
+0,018
ø40 -0,002
[1.575 +.0007
-.0001 ]
56
[2.205]
M12
min 25 [.984] Deep
M12
min 25 [.984] Deep
CO-ø1½" straight, Parallel key 3 8"x 3 8"x 2¼" BS46
K - tapered 1:10, Parallel key B12x8x28 DIN 6885
Max. Torque 132,8 daNm [11755 lb-in]
Max. Torque 210,7 daNm [18650 lb-in]
82 -0,2
[3.228 -.0079 ]
4
B [.157]
°
R2±0,2
[.0787±.0078]
12 +0,01
-0,05
[.472 +.0004
-.0019 ]
[1.5 -.0019]
ø38,1 -0,05
ø50
[1.968]
42,4 -0,2
[1.669-.0079 ]
ø50
[1.968]
82 -0,2
[3.228 -.0079 ]
9.545 -0,02
[.379-.0008]
B-B
6
[.236]
ø6
[.236]
54±0,4
[2.126±.0157]
S=46
Tightening Torque
50±3 daNm
[4425±265 lb-in]
B
Taper 1:10
ø56
[2.205]
R2±0,2
[.0787±.0078]
M30x2
45
Pitch 12/24
Teeth 17
0
Pressure angle 30
82 -0,2
[3.228 -.0079 ]
5:1
ø50
[1.968]
[1.693-.0079]
°
R2±0,2
[.0787±.0078]
82 -0,2
[3.228 -.0079 ]
12 -0,043
[.472-.0017]
43 -0,2
45
R2±0,2
[.0787±.0078]
R2±0,2
[.0787±.0078]
16,15 -0,2
[.634-.0079]
45
Max. Torque 132,8 daNm [11755 lb-in]
mm [in]
3/8-16 UNC
min 25 [.984] deep
PERMISSIBLE SHAFT LOADS
The curves apply to a B10 bearing life (ISO281) of 2000 hours at 200 RPM.
Pr
lbs
MTM
Pr
daN
5600
Pr
lbs
12000
12000
5000
5000
10000
10000
4000
4000
8000
8000
3000
3000
6000
6000
4000
2000
4000
2000 1000
0
MTMC
Pr
daN
5600
2000
2000 1000
0
-80
-3
-60
-2
-40
-20
-1
0
0
20
40
60
1
80
3
2
Pr
lbs
100
120
4
140
5
0
-80
0
mm
160
-60
-3
7 in
6
-40
-2
-20
-1
0
20
40
0
1
160
mm
MTMW
Pr
daN
5600
12000
5000
10000
4000
8000
3000
6000
4000
2000
2000 1000
0
0
-80
-3
-60
-2
-40
-20
-1
0
0
20
1
40
60
2
25
80
3
100
4
120
5
140
6
7 in
60
2
80
3
100
4
120
5
140
160 mm
6
in
MTM
MOTORS
DIMENSIONS AND MOUNTING DATA - MTMV
45,6 -1
[1.795 -.0394]
14 max
[.551]
T
21±0,2
[.827±.0078]
ø110±0,1
[4.33±.0039]
9xM12
139
[5.472]
84±0,3
[3.307±.0118]
ø139
[5.472]
ø139 -0,2
[5.472 -.0079]
Port B
Port A
P(A,B)
L1
L3
72
[2.834]
L2
max L
mm [in]
Warning: Drain line should always be used.
P(A, B): 2xG3/4 - 17 mm [.669 in] depth
T : G1/4 12 mm [.472 in] depth (plugged)
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
L, mm [in]
Type
MTMV 200 151 [5.945]
MTMV 250 157 [6.181]
MTMV 315 167 [6.575]
MTMV 400 177 [6.968]
MTMV 470 185 [7.283]
MTMV 500 191 [7.520]
MTMV 630 187 [7.362]
MTMV 725 196 [7.717]
L1, mm [in]
25 [.98]
31,3 [1.23]
40,5 [1.59]
51 [2.01]
59 [2.32]
65 [2.56]
61 [2.40]
70 [2.76]
L2, mm [in] L3, mm [in]
106,5 [4.193] 27,8 [1.094]
112,8 [4.441] 26,5 [1.043]
122,0 [4.803] 22,3 [.878]
132,5 [5.217] 21,8 [.858]
140,5 [5.531] 23,8 [.937]
146,5 [5.768] 27,8 [1.094]
142,5 [5.610] 26,8 [1.055]
151,5 [5.965] 27,8 [1.094]
DIMENSIONS OF THE ATTACHED COMPONENT
47 +0,5
[1.85+.0197 ]
T
ø90
[3.543]
min ø55
[2.165]
K
16DP 12/24
17 +0,4
[.669 +.0157 ]
ANS B92.1-76
F
J
I
F: Oil circulation hole
J: 9xM12-30 mm [1.181 in] depth, 400, ø110±0,1 [4.33±.0039]
26
I: O- Ring 93x1,5mm [3.661x.059 in]
T: Drain connection G1/4
MTM
MOTORS
DIMENSIONS AND MOUNTING DATA - MTM6V
45,6 -1
[1.795 -.0394]
10°
14 max
[.551]
T
21±0,2
[.827±.0078]
ø110±0,1
[4.33±.0039]
40°
84±0,3
[3.307±.0118]
20°
139
[5.472]
ø139
[5.472]
ø139 -0,2
[5.472 -.0079]
Port B
6xM12
20°
Port A
P(A,B)
40°
L1
L3
10°
L2
72
[2.834]
max L
Fig.1
mm [in]
Warning: Drain line should always be used.
P(A, B): 2xG3/4 - 17 mm [.669 in] depth
T : G1/4 12 mm [.472 in] depth (plugged)
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
Type
MTM6V 200
MTM6V 250
MTM6V 315
MTM6V 400
MTM6V 470
MTM6V 500
MTM6V 630
MTM6V 725
L, mm [in]
151 [5.945]
157 [6.181]
167 [6.575]
177 [6.968]
185 [7.283]
191 [7.520]
187 [7.362]
196 [7.717]
L1, mm [in]
25 [.98]
31,3 [1.23]
40,5 [1.59]
51 [2.01]
59 [2.32]
65 [2.56]
61 [2.40]
70 [2.76]
L2, mm [in] L3, mm [in]
106,5 [4.193] 27,8 [1.094]
112,8 [4.441] 26,5 [1.043]
122,0 [4.803] 22,3 [.878]
132,5 [5.217] 21,8 [.858]
140,5 [5.531] 23,8 [.937]
146,5 [5.768] 27,8 [1.094]
142,5 [5.610] 26,8 [1.055]
151,5 [5.965] 27,8 [1.094]
DIMENSIONS OF THE ATTACHED COMPONENT FOR MTM6V
47 +0,5
[1.85+.0197 ]
J
ø90
[3.543]
K
T
min ø55
[2.165]
17 +0,4
[.669 +.0157 ]
16DP 12/24
ANS B92.1-76
F
I
F: Oil circulation hole
0
J: 9xM12-30 mm [1.181 in] depth, 40 , ø110±0,1 [4.33±.0039]
or 6xM12-30 mm [1.181 in] depth, situated in accordance
with the bolts M12, shown on Fig.1, ø110±0,1 [4.33±.0039]
I: O- Ring 93x1,5mm [3.661x.059 in]
T: Drain connection G1/4
DRAIN CONNECTION
A drain line ought to be used when pressure in the return line can exceed the permissible pressure. It can be
connected at the drain connection of the attached component. The maximum pressure in the drain line is limited by
the attached component and its shaft seal.
The drain line must be possible for oil to flow freely between motor and attached component and must be led to the
tank. The maximum pressure in the drain line is limited by the attached component and its seal.
27
MTM
MOTORS
INTERNAL SPLINE DATA FOR THE ATTACHED COMPONENT
Standard ANS B92.1-1976, class 5
[m=2.1166; corrected x.m=+1,0]
Fillet Root Side Fit
Number of Teeth
Diametral Pitch
Pressure Angle
Pitch Dia.
Major Dia.
Minor Dia.
Circular Space Width
Fillet Radius
Dimension Between
Two Pins
Pin Dia.
mm
16
12/24
0
30
33,8656
+0,4
38,4
+0,04
32,15
4,516±0,037
0,5
+0,10
26,9
D
Dri
Di
Lo
R
L
inch
16
12/24
0
30
1.3333
1.5118÷1.5275
1.2657÷1.2673
.1763÷.1791
.02
1.063÷1.059
d
.19026÷.19034 4,835±0,001
z
DP
L
Hardening Specification:
HV=750±50 on the surface.
HV=560 at 0,7±0,2 [.035÷.019] case depth
Material: 20 MoCr4 EN 10084 or SAE8620.
ORDER CODE
1
2
3
4
5
6
7
MTM
Pos.1 - Mounting Flange
omit - 4-Bolt flange, spigot dia. ø160, BC ø200
C
- 4-Bolt flange, spigot dia. ø125, BC ø160
Pos.3 - Shaft Extensions*
- ø40 straight, Parallel key A12x8x70 DIN6885
C
3
3
CO - ø1½ ” straight, Parallel key /8”x /8”x2¼” BS46
W
- Wheel motor
K
- ø45 tapered 1:10, Parallel key B12x8x28 DIN6885
V
- Very short mount, 9xM12 mounting bolts
SH
- ø1½" splined 17T ANSI B92.1-1976
6V
- Very short mount, 6xM12 mounting bolts
Pos.4 - Check Valves
Pos.2 - Displacement code
200
250
315
400
470
500
630
725
- 201,4 cm3/rev [12.29 in3/rev]
- 251,8 cm3/rev [15.36 in3/rev]
- 326,3 cm3/rev [19.90 in3/rev]
- 410,9 cm3/rev [25.06 in3/rev]
- 475,0 cm3/rev [28.97 in3/rev]
- 523,6 cm3/rev [31.95 in3/rev]
- 631,2 cm3/rev [38.52 in3/rev]
- 724,3 cm3/rev [44.20 in3/rev]
omit - without check valves
1
- with check valves
Pos.5 - Ports
omit - BSPP (ISO 228)
Pos.6 - Special Features (see page 48)
Pos.7 - Design Series
omit - Factory specified
NOTES:
* The permissible output torque for shafts must be not exceeded!
The hydraulic motors are mangano-phosphatized as standard.
28
HYDRAULIC MOTORS TMF
APPLICATION
»
»
»
»
»
»
»
A
Marine equipment
Forestry equipment
Metal working machines
Agriculture machines
Road building machines
Mining machinery
Special vehicles etc.
B
CONTENTS
OPTIONS
Specification data ............................................ 30
Dimensions and mounting TMF....................... 31
Dimensions and mounting TMFA .................... 32
Permissible shaft loads ................................... 33
Order code ...................................................... 33
» Model- Disc valve, roll-gerotor
» Wheel mounting flange
» Side ports
» Shaft- thread hole flange
» SAE and BSPP ports
» Other special features
GENERAL
Max. Displacement,
cm3/rev [in3/rev]
Max. Speed,
724,3 [44.2]
750
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
cont.: 175 [15490]
70 [94]
cont.: 250 [3600]
5
[RPM]
Permissible Shaft Loads
Pa=1000 [2250]
daN [lbs]
Pressure fluid
int.: 350 [5080]
150 [40]
lpm [GPM]
Min. Speed,
int.: 215 [16030]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
O
Temperature range,
O
C [ F]
-40÷140 [-40÷284]
2
20÷75 [98÷347]
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Pressure Losses
Oil flow in drain line
flow in
Pressure drop Viscosity Oil
drain
line
bar [PSI]
mm 2/s [ SUS] lpm [GPM ]
20 [98]
200 [2 90 0]
2 75 [3990]
2,5 [.660 ]
35 [164]
1,5 [ .400]
20 [98]
4 [1.057]
35 [164]
2,5 [.660]
350
25
300
20
250
200
150
15
10
100
5
50
0
0
0
0
29
25
5
75
50
10
15
20
100
25
125 Q, lpm
30
Q, GPM
MLHV
TMF
MOTORS
SPECIFICATION DATA
Type
Displacement,
3
3
cm /rev [in /rev]
TMF
200
TMF
250
TMF
315
201,4
TMF
400
TMF
470
TMF
500
TMF
630
TMF
725
251,8
326,3
410,9
475
523,6
631,2
724
[12.29]
[15.36]
[19.9]
[25.06]
[28.97]
[31.95]
[38.52]
[44.2]
Max. Speed,
Cont.
625
500
380
305
260
240
185
170
[RPM]
Int.*
750
600
460
365
315
285
225
215
Max. Torque
Cont.
72 [6375] 90[7965] 116[10265] 147[13010] 171[15135] 172[15225] 175[15490] 160[14160]
daNm [lb-in]
Int.*
102 [9030] 128[11330] 163[14425] 206[18232] 215[16030] 215[19030] 215[19030] 192[17000]
Peak**
115[10180] 144[12745] 186[16460] 235[20800] 240[21240] 240[21240] 250[21225] 240[21240]
Max. Output
Cont.
41 [55]
41 [55]
41 [55]
41 [55]
41 [55]
37,5 [50]
28 [37,5]
26 [35]
kW [HP]
Int.*
65 [87]
70 [94]
70 [94]
70 [94]
55 [74]
51 [68]
42 [56]
40 [54]
Max. Pressure Drop
Cont.
250[3600] 250[3600] 250[3600] 250[3600] 250[3600] 230[3340] 185[2680] 160[2320]
bar [PSI]
Int.*
350[5080] 350[5080] 350[5080] 350[5080] 350[5080] 280[4060] 225[3260] 210[3045]
Peak**
400[5800] 400[5800] 400[5800] 400[5800] 400[5800] 320[4640] 270[3915] 260[3770]
Max. Oil Flow
Cont.
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
125[33]
lpm [GPM]
Int.*
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
150[40]
Max. Inlet Pressure
Cont.
270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]
bar [PSI]
Int.*
370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]
Peak**
420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]
Max. Return Pressure
Cont.
without Drain Line or
Cont. 100-300 RPM 40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
40 [580]
Max. Pressure
Cont.
20 [290]
20 [290]
20 [290]
20 [290]
-
-
-
in Drain Line, bar [PSI]
Int.*
0-100 RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]
>300 RPM 20 [290]
0-max. RPM 75 [1100] 75 [1100] 75 [1100] 75 [1100]
75 [1100] 75 [1100] 75 [1100] 75 [1100]
75 [1100] 75 [1100] 75 [1100] 75 [1100]
Max. Return Pressure
Cont.
270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920] 270[3920]
with Drain Line
Int.*
370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370] 370[5370]
bar [PSI]
Peak**
420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100] 420[6100]
Max. Starting Pressure with
Unloaded Shaft, bar [PSI]
Min. Starting Torque daNm [lb-in]
Min. Speed***, [RPM]
Weight, kg [lb]
6 [90]
6 [90]
60[5310]
75[6640]
5
5
6 [90]
6 [90]
6 [90]
6 [90]
6 [90]
6 [90]
97[8585] 122[10800] 142[12570] 143[12655] 145[12830] 148[13100]
5
26,9[59.3] 27,3[60.2] 28,1[62]
5
29 [64]
5
5
5
5
29,7[65.5] 30,2[66.6] 29,7[65.5]
31[68.4]
Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
*
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 70 SUS [13 cm2/s] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
30
MLHV
TMF
MOTORS
DIMENSIONS AND MOUNTING DATA - TMF
60
60
5x 1
5
72
[2.835]
5
ø189
[7.441]
ø180
[7.087]
ø172
[6.772]
10xø14,2 +0,15
5xM14x1,5
[.559+.0059 ]
(ø238)
[9.37]
18
[.708]
6
[.236]
P(A,B)
21±0,15
[.827±.0059]
ø139
[5.472]
42±0,15
42±0,15
[1.654±.0059] [1.654±.0059]
Port B
ø92,8
[3.654]
ø180
[7.087]
5x 1
0
ø14 2]
1
[5.5
ø2
[8.2 10
68]
Port A
T
L1
7
12
[.276]
[.472]
113 max
[4.449]
5
[.197]
P(A, B): 2xG3/4 - 17 mm [.669 in] depth
T : G1/4 - 12 mm [.472 in] depth
L2
L3
mm [in]
max L
Warning: Drain line should always be used.
Type
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
TMF 200
TMF 250
TMF 315
TMF 400
TMF 470
TMF 500
TMF 630
TMF 725
31
L, mm [ in]
L1, mm [in] L2,mm [in] L3, mm [in]
126 [4.96]
.98 [25]
83 [3.268] 110,3 [4.34]
132.3 [5.21] 31,3 [1.23] 89.3 [3.516] 116,6 [4.59]
141.5[5.57] 40,5 [1.59] 98.5 [3.878] 125,8 [4.95]
152 [5.98]
51 [2.01] 109 [4.291] 136,3 [5.37]
160 [6.30]
59 [2.32] 117 [4.606] 144,3 [5.68]
166 [6.54]
65 [2.56] 123 [4.843] 150,3 [5.92]
162 [6.38]
61 [2.40] 119 [4.69] 146,3 [5.76]
171 [6.73]
70 [2.76] 128 [5.04] 155,3 [6.11]
MLHV
TMF
MOTORS
DIMENSIONS AND MOUNTING DATA - TMFA
60
5x 1
5
ø189
10xø14,2 +0,15
[.559+.0059 ]
ø152,4
ø210
[6.0]
[8.268]
ø238
18
[.708]
6
[.236]
[9.37]
P(A,B)
21±0,15
[.827±.0059]
Port A
L1
7
12
[.276]
[.472]
5
113 max
[.197]
[4.449]
T
[5.472]
ø139
ø109,22
[4.3]
42±0,15
42±0,15
[1.654±.0059][1.654±.0059]
Port B
P(A, B): 2x1 1/16-12 UN, O-ring port
17 mm [.669 in] depth
T : 9/16-18 UNF, O-ring port
12 mm [.472 in] depth
L2
L3
max L
mm [in]
Warning: Drain line should always be used.
Type
TMFA 200
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
TMFA 250
TMFA 315
TMFA 400
TMFA 470
TMFA 500
TMFA 630
TMFA 725
32
L, mm [ in]
L1, mm [in] L2,mm [in] L3, mm [in]
126 [4.96]
.98 [25]
83 [3.268] 110,3 [4.34]
132.3 [5.21] 31,3 [1.23] 89.3 [3.516] 116,6 [4.59]
141.5[5.57] 40,5 [1.59] 98.5 [3.878] 125,8 [4.95]
152 [5.98]
51 [2.01] 109 [4.291] 136,3 [5.37]
160 [6.30]
59 [2.32] 117 [4.606] 144,3 [5.68]
166 [6.54]
65 [2.56] 123 [4.843] 150,3 [5.92]
162 [6.38]
61 [2.40] 119 [4.69] 146,3 [5.76]
171 [6.73]
70 [2.76] 128 [5.04] 155,3 [6.11]
[7.441]
ø180
[7.087]
72
[2.835]
5
ø172
[6.772]
5x 1
ø180
[7.087]
60
6x5/8-18 UNF
MLHV
TMF
MOTORS
PERMISSIBLE SHAFT LOADS
The load diagram is valid for an average bearings life of 2000 hours at 100 RPM
Prad
daN
12000
0.5
1
1.5
2
2.5
3
3.5
4
4.5 L, in
24000
B
10000
Prad
lbs
26000
22000
20000
18000
8000
A
16000
14000
6000
12000
10000
4000
8000
6000
2000
4000
2000
0
10
20
30
40
50
60
70
80
90
100
110
120 L, mm
A - Permissible radial shaft load.
B - Max. radial shaft load. Any shaft load exceeding the values shown in the curve
will involve a risk of breakage
ORDER CODE
1
2
3
4
TMF
Pos.1 - Mounting Flange
omit - Thread hole flange, 5xM12x1,5 on ø140
A
- Thread hole flange, 6x5/8-18 UNF on ø152,4
Pos.2 - Displacement code
200
250
315
400
470
500
630
725
3
3
- 201,4 cm /rev [12.29 in /rev]
3
3
- 251,8 cm /rev [15.36 in /rev]
3
3
- 326,3 cm /rev [19.90 in /rev]
3
3
- 410,9 cm /rev [25.06 in /rev]
3
3
- 475,0 cm /rev [28.97 in /rev]
3
3
- 523,6 cm /rev [31.95 in /rev]
3
3
- 631,2 cm /rev [38.52 in /rev]
3
3
- 724,3 cm /rev [44.20 in /rev]
Pos.3 - Special Features (see page 48)
Pos.4 - Design Series
omit - Factory specified
The hydraulic motors are mangano-phosphatized as standard.
33
HYDRAULIC MOTORS MVM
APPLICATION
»
»
»
»
»
»
»
»
Conveyors
Metal working machines
Agriculture machines
Road building machines
Mining machinery
Food industries
Special vehicles
Plastic and rubber machinery etc.
A
A
B
B
OPTIONS
» Model- Disc valve, roll-gerotor
» Flange with wheel mount
» Short motor
» Side ports
» Shafts- straight, splined and tapered
» BSPP ports;
» Other special features.
CONTENTS
Specification data .......................... 35
Dimensions and mounting ............... 36
Shaft extensions ............................ 36
Permissible shaft Seal Pressure .... 37
Permissible shaft loads .................. 38
Order code ..................................... 38
EXCELLENCE
» High torque and pressure drop
» High inlet pressure
» High starting torque
» Improved efficiency at high pressure drop
» Smooth operation at low speed
» High radial and axial bearing capacity
GENERAL
Max. Displacement,
3
3
801,8 [48.91]
cm /rev [in /rev]
Max. Speed,
763
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
cont.: 259 [22920]
112 [150]
cont.: 250 [3630]
5
[RPM]
Permissible Shaft Loads,
int.: 350 [5080]
240 [63.4]
lpm [GPM]
Min. Speed,
int.: 340 [30090]
Pa=1500 [3370]
daN [lbs]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Pressure fluid
O
Temperature range,
-40÷140 [-40÷284]
O
C [ F]
20÷75 [98÷347]
2
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Pressure Losses
Oil flow in drain line
30
400
flow in
Pressure drop Viscosity Oil
drain line
2
bar [PSI]
mm /s [ SUS] lpm [GPM ]
200 [2 90 0]
2 75 [3990]
20 [98]
2,5 [.660 ]
35 [164]
1,5 [ .400]
20 [98]
4 [1.057]
35 [164]
2,5 [.660]
25
300
200
20
15
10
100
0
5
0
0
0
34
25
5
50
10
15
75
20
100
25
125
30
35
150
40
200 Q, lpm
175
45
50
Q, GPM
MVM
MOTORS
SPECIFICATION DATA
MVM
315
Type
Displacement, cm3/rev [in3/rev]
Max. Speed,
[RPM]
Max. Torque
daNm [lb-in]
MVM
400
MVM
500
MVM
630
MVM
800
314,5 [19.19 ] 400,9 [ 24.5 ] 499,6 [ 30.5] 629,1 [ 38.38 ] 801,8 [ 48.91 ]
cont.
Int.*
500
636
600
763
400
315
480
380
250
300
cont.
115 [10180] 144 [12745] 180 [15930] 227 [20090]
259 [22920]
Int.*
160 [14160] 200 [17700] 260 [23010] 310 [27440]
340 [30090]
peak**
180 [15930] 230 [20355] 286 [25315] 360 [31860]
402 [35580]
Max. Output
cont.
67 [90]
67 [90]
67 [90]
67 [90]
67 [90]
kW [HP]
int.*
112 [150]
112 [150]
112 [150]
112 [150]
112 [150]
Max. Pressure Drop
cont.
250 [3630]
250 [3630]
250 [3630]
250 [3630]
225 [3263]
bar [PSI]
Int.*
350 [5080]
350 [5080]
350 [5080]
350 [5080]
300 [4350]
peak**
400 [5800]
400 [5800]
400 [5800]
400 [5800]
350 [5080]
Max. Oil Flow
cont.
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
lpm [GPM]
Int.*
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
Max. Inlet Pressure
cont.
270 [3915]
270 [3915]
270 [3915]
270 [3915]
270 [3915]
bar [PSI]
Int.*
370 [5365]
370 [5365]
370 [5365]
370 [5365]
370 [5365]
peak**
420 [6090]
420 [6090]
420 [6090]
420 [6090]
420 [6090]
Max. Return Pressure
cont.
140 [2030]
140 [2030]
140 [2030]
140 [2030]
140 [2030]
with Drain Line
Int.*
175 [2540]
175 [2540]
175 [2540]
175 [2540]
175 [2540]
bar [PSI]
peak**
210 [3045]
210 [3045]
210 [3045]
210 [3045]
210 [3045]
5 [70]
5 [70]
5 [70]
Max. Starting Pressure with Unloaded Shaft,
bar [PSI]
Min. Starting Torque daNm [lb-in]
Min. Speed***, [RPM]
Weight, kg [lb]
5 [70]
92 [8140]
115 [10180] 144 [12745] 180 [15930]
5 [70]
205 [18145]
10
6
8
6
5
41,3 [91]
42,1 [93]
43 [95]
44,5 [98]
46 [101.4]
* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
2
4. Recommended minimum oil viscosity 13 mm /s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
35
MVM
MOTORS
DIMENSIONS AND MOUNTING DATA
CO Shaft
K Shaft
SH Shaft
C Shaft
ø160 -0,063
L2
20±0,3
[.787±.012]
[.433 +.0079]
Shaft Dim.
See Page 37
11+0,2
145 [5.71]
122 [4.8]
79 [3.11]
105 [4.134]
[6.3 -.0025 ]
L1
15±0,15
[.59±.0059]
21±0,15
[.827±.0059]
max L
ø160 [6.299]
P(A,B)
50±0,15
50±0,15
[1.97±.0059] [1.97±.0059]
T
85 -0,5
[3.35 -.0196 ]
160
[6.299]
Port A
ø200±0,4
[7.87±.016]
4xø18
[.708]
179 [7.05]
Port B
Versions
P (A,B)
T
2
4
2xG1
G¼
2x15/ 16 -12UN
9
/ 16 -18UNF
Warning: Drain line should always be used.
179 [7.05]
Type
L,mm [in]
L2,mm [in]
L1,mm [in]
MVM 315 226,5 [8.92]
172,5 [6.79] 25,5 [1.00]
MVM 400 233,5 [9.19]
179,5 [7.07] 32,5 [1.28]
MVM 500 241,5 [9.51]
187,5 [7.38] 40,5 [1.59]
MVM 630
252 [9.92]
198 [7.79]
51 [2.01]
MVM 800 266 [10.47]
212 [8.35]
65 [2.56]
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
mm [in]
36
MVM
MOTORS
SHAFT EXTENSIONS
C - ø50 straight, Parallel key A14x9x70 DIN 6885
12,72-0,02
[.502-.0008]
ø60 [2.362]
+.0008
M12
min 26 [1.024] deep
ø57,15 - 0,015
[2.25 - .0006]
79 [3.11]
ø62,9- 0,2
[2.48 - .0079]
[1.968 +.0007 ]
+0,018
ø50 +0,002
ø60 [2.362]
79 [3.11]
+.0197
[2.086+.0079
]
3/8-16 UNC
min 25 [.98] deep
K - tapered 1:10, Parallel key B16x10x32 DIN 6885
70 [2.756]
79 [3.11]
16 -0,043
[.63 -.0017 ]
M12
min 26 [1.024] deep
7
[.275]
S=65
Tightening Torque
70±1 daNm
[6196±88.5 lb-in]
ø8
[.315]
40 [1.575]
ø60 [2.362]
32,25 - 0,2
[2.27- .0079 ]
ø53,975 - 0,025
[2.125 - .001]
56 +2
[2.205+.079 ]
ø60 [2.362]
A
A-A
ø78 [3.01]
SH - ø2 1/8 "splined, 16 DP 8/16 ANS B92.1-1976
M42x3
+0,5
ø53 +0,2
14 -0,043
[.551-0017]
CO - ø2¼"[57,15] straight,Parallel key ½ "x½"x 2¼" BS46
A
Taper 1:10
105 [4.134]
6
[.236]
mm [in]
MAX. PERMISSIBLE SHAFT SEAL PRESSURE
Max. return pressure without drain line or
max. pressure in the drain line
DP
[PSI]
1000
DP
[bar]
80
70
60
750
50
- continuous operations
- intermittent operations
40
500
30
250
20
10
0
n
0
0
50 100 150 200 250 300 350 400 450 500 550 600 [RPM]
37
MVM
MOTORS
PERMISSIBLE SHAFT LOADS
The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft
load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor life. The two other curves
apply to a B10 bearing life of 3000 hours at 200 RPM.
Prad
daN
-4
-3
-2
-1
0
1 in
Prad
lbs
14000
6000
1500 daN
3370 lbs.
5000
1
2
12000
1500 daN
3370 lbs.
10000
4000
2 - Pa=0 daN [0 lbs]
3 - Pa=1500 daN [3370 lbs]
8000
3000
3 6000
2000
4000
1000
2000
-125 -100 -75
-50
-25
0
50 mm
25
ORDER CODE
1
2
3
4
5
6
MVM
Pos.1 - Displacement code
315
400
500
630
800
3
Pos.3 - Ports
3
- 314,5 cm /rev [19.8 in /rev]
- 400,9 cm3/rev [24.45 in3/rev]
- 499,6 cm3/rev [30.48 in3/rev]
- 629,1 cm3/rev [38.38 in3/rev]
- 801,8 cm3/rev [48.91 in3/rev]
2
4
- side ports, 2xG1, G1/4, BSP thread, ISO 228
- side ports, 2x1 5/16-12 UN, O-ring, 9/16-18 UNF
Pos.4 - Check Valves
omit - without check valves
1
- with check valves
Pos.2 - Shaft Extensions*
Pos.5 - Special Features (see page 48)
- ø50 straight, Parallel key A14x9x70 DIN6885
C
1
1
1
1
CO - ø2 /4" straight, Parallel key /2"x /2"x2 /4" BS 46
Pos.6 - Design Series
omit - Factory specified
1
SH
- ø2 /8" splined, ANSI B92.1-1976
K
- ø60 tapered 1:10, Parallel key B16x10x32 DIN6885
NOTES:
* The permissible output torque for shafts must be not exceeded!
The hydraulic motors are mangano-phosphatized as standard.
38
HYDRAULIC MOTORS MVMC
OPTIONS
A
A
B
B
» Model- Disc valve, roll-gerotor
» Flange mount with wheel mount
» Side ports
» Shafts- straight, splined and tapered
» Metric, SAE and BSPP ports
» Other special features
CONTENTS
EXCELLENCE
Specification data .......................... 40
Dimensions and mounting ............... 41
Shaft extensions ............................ 42
Permissible shaft Seal Pressure .... 42
Permissible shaft loads .................. 43
Order code ..................................... 43
» High torque and pressure drop
» High inlet pressure
» High starting torque
» Improved efficiency at high pressure
drop and frequent reversing
» Smooth operation at low speed
» High radial and axial bearing capacity
GENERAL
Max. Displacement,
3
3
801,8 [48.91]
cm /rev [in /rev]
Max. Speed,
763
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
cont.: 259 [22920]
112 [150]
cont.: 250 [3630]
5
[RPM]
Permissible Shaft Loads,
int.: 350 [5080]
240 [63.4]
lpm [GPM]
Min. Speed,
int.: 340 [30090]
Pa=1500 [3370]
daN [lbs]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Pressure fluid
O
Temperature range,
-40÷140 [-40÷284]
O
C [ F]
20÷75 [98÷347]
2
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Pressure Losses
Oil flow in drain line
30
400
flow in
Pressure drop Viscosity Oil
drain line
2
bar [PSI]
mm /s [ SUS] lpm [GPM ]
200 [2 90 0]
2 75 [3990]
20 [98]
2,5 [.660 ]
35 [164]
1,5 [ .400]
20 [98]
4 [1.057]
35 [164]
2,5 [.660]
25
300
200
20
15
10
100
0
5
0
0
0
39
25
5
50
10
15
75
20
100
25
125
30
35
150
40
200 Q, lpm
175
45
50
Q, GPM
MVMC
MOTORS
SPECIFICATION DATA
MVMC
315
Type
Displacement, cm3/rev [in3/rev]
MVMC
400
314,5 [19.18] 400,9 [24.5]
MVMC
500
MVMC
630
MVMC
800
499,6 [30.5]
629,1 [38.38]
801,8 [48.91]
315
250
Max. Speed,
cont.
636
500
400
[RPM]
Int.*
736
600
480
380
300
259 [22920]
Max. Torque
cont.
115 [10180]
144 [12745]
180 [15930]
227 [20090]
daNm [lb-in]
Int.*
160 [14160]
200 [17700]
260 [23010]
310 [27440]
340 [30090]
peak**
180 [15930]
230 [20355]
286 [25315]
360 [31860]
402 [35580]
start
92 [8143]
115 [10180]
144 [12745]
180 [15930]
205 [18144]
Max. Output
cont.
67 [90]
67 [90]
67 [90]
67 [90]
67 [90]
kW [HP]
int.*
112 [150]
112 [150]
112 [150]
112 [150]
112 [150]
Max. Pressure Drop
cont.
250 [3630]
250 [3630]
250 [3630]
250 [3630]
225 [3263]
bar [PSI]
Int.*
350 [5080]
350 [5080]
350 [5080]
350 [5080]
300 [4350]
peak**
400 [5800]
400 [5800]
400 [5800]
400 [5800]
350 [5080]
Max. Oil Flow
cont.
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
lpm [GPM]
Int.*
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
5 [70]
5 [70]
5 [70]
5 [70]
5 [70]
48,3 [106.5]
50,4 [111.1]
Max. Starting Pressure with Unloaded
Shaft, bar [PSI]
Patm.
Drain Pressure, bar [PSI]
Weight, kg [lb]
43,8 [96.6]
44,9 [99]
45,8 [101]
Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds of 5 RPM lower than given, consult factory or your regional manager.
*
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal filtration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil, HLP(DIN51524) or HM(ISO6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 70 SUS [13 cmі/s] at 122°F [50°C].
5. Recommended maximum system operating temperature is 180°F [82°C].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
40
MVMC
MOTORS
DIMENSIONS AND MOUNTING DATA
SH Shaft
C Shaft
CO Shaft
K Shaft
23
[.91]
63 [2.48]
8,8
[.346]
145 [5.7]
105 [4.13]
82 [3.23]
79 [3.11]
122 [4.8]
79 [3.11]
ø179,968±0,05
[7.085±.00196]
Shaft Dim.
See Page 42
L1
max L
L2
T
50±0,15
[1.97±.0059]
145±0,5
[5.7±.0197]
21±0,15
[.827±.0059]
18±0,2
[.708±.00787]
50±0,15
[1.97±.0059]
18±0,2
[.708±.00787]
7,5±0,2
[.29±.00787]
18±0,2
[.708±.00787]
28,5±0,2
[1.12±.00787]
18±0,2
[.708±.00787]
P(A,B)
85 -0,5
[3.346 -.0197 ]
C
2x M10
Thru.
4x ø18
[.709]
ø200
[7.874]
Versions
3
4x90
o
45 o
(194 [7.638])
mm [in]
P (A,B) 2xG1
T
G¼
C
6xM10
Warning: Drain line should always be used.
Type
L,mm [in]
L2,mm [in]
ø224
[8.819]
L1,mm [in]
MVMC 315 227,5 [8.957] 174,0 [6.850] 25,5 [1.00]
30 o
MVMC 400 234,5 [9.232] 181,0 [7.126] 32,5 [1.28]
(194 [7.638])
MVMC 500 242,5 [9.547] 189,0 [7.441] 40,5 [1.59]
MVMC 630 253,0 [9.961] 199,5 [7.854] 51,0 [2.01]
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
MVMC 800 267,0 [10.518] 213,5 [8.405] 65,0 [2.56]
41
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
MVMC
MOTORS
SHAFT EXTENSIONS
C - ø50 straight, Parallel key A14x9x70 DIN 6885
12,72-0,02
[.502-.0008]
M12
min 26 [1.024] deep
ø60 [2.362]
ø57,15 - 0,015
[2.25 - .0006]
82 [3.24]
ø2,9 - 0,2
[2.48 - .0079]
+.0008
+0,018
ø50 +0,002
ø60 [2.362]
[1.968 +.0007 ]
79 [3.11]
3/8-16 UNC
min 26 [1.24] deep
K - tapered 1:10, Parallel key B16x10x32 DIN 6885
70 [2.756]
79 [3.11]
16 -0,043
[.63 -.0017 ]
M12
min 26 [1.024] deep
7
[.275]
S=65
Tightening Torque
70±1 daNm
[6196±88.5 lb-in]
ø8
[.315]
40 [1.575]
ø60 [2.362]
32,25 - 0,2
[2.27- .0079 ]
ø53,975 - 0,025
[2.125 - .001]
56 +2
[2.205+.079 ]
ø60 [2.362]
A
A-A
ø78 [3.01]
SH - ø2 1/8 "splined, 16 DP 8/16 ANS B92.1-1976
M42x3
+.0197
[2.086+.0079
]
+0,5
ø53 +0,2
14 -0,043
[.551-0017]
CO - ø2¼"[57,15] straight,Parallel key ½ "x½"x 2¼" BS46
A
Taper 1:10
105 [4.134]
6
[.236]
mm [in]
MAX. PERMISSIBLE SHAFT SEAL PRESSURE
Max. return pressure without drain line or
max. pressure in the drain line
DP
[PSI]
1000
DP
[bar]
80
70
60
750
50
- continuous operations
- intermittent operations
40
500
30
250
20
10
0
n
0
0
50 100 150 200 250 300 350 400 450 500 550 600 [RPM]
42
MVMC
MOTORS
PERMISSIBLE SHAFT LOADS
The output shaft runs in tapered bearings that permit high axial and radial forces. Curve "1" shows max. radial shaft
load. Any shaft load exceeding the values quoted in the curve will seriously reduce motor life. The two other curves
apply to a B10 bearing life of 3000 hours at 200 RPM.
Prad
daN 0
1
2
3
4
Prad
lbs
6 in
5
14000
6000
1500 daN
3370 lbs.
5000
1
2
12000
1500 daN
3370 lbs.
10000
2 - Pa=0 daN [0 lbs]
3 - Pa=1500 daN [3370 lbs]
4000
8000
3000
3 6000
2000
4000
1000
2000
0
25
50
75
100
125
150
175 mm
ORDER CODE
1
2
3
4
5
6
MVMC
Pos.1 - Displacement code
315
400
500
630
800
3
Pos.3 - Ports
3
- 314,5 cm /rev [19.8 in /rev]
- 400,9 cm3/rev [24.45 in3/rev]
- 499,6 cm3/rev [30.48 in3/rev]
- 629,1 cm3/rev [38.38 in3/rev]
- 801,8 cm3/rev [48.91 in3/rev]
3
- side ports 2xG1, G1/4, BSP thread, ISO 228,
6xM10
Pos.4 - Check Valves
omit - without check valves
1
- with check valves
Pos.2 - Shaft Extensions*
Pos.5 - Special Features (see page 48)
- ø50 straight, Parallel key A14x9x70 DIN6885
C
1
1
1
1
CO - ø2 /4" straight, Parallel key /2"x /2"x2 /4" BS46
Pos.6 - Design Series
omit - Factory specified
1
SH
- ø2 /8" splined, ANSI B92.1-1976
K
- ø60 tapered 1:10, Parallel key B16x10x32 DIN6885
NOTES:
* The permissible output torque for shafts must be not exceeded!
The hydraulic motors are mangano-phosphatized as standard.
43
HYDRAULIC MOTORS VMF
APPLICATION
»
»
»
»
»
»
»
A
Marine equipment
Forestry equipment
Metal working machines
Agriculture machines
Road building machines
Mining machinery
Special vehicles etc.
B
CONTENTS
OPTIONS
Specification data ............................................ 45
Dimensions and mounting ............................... 46
Permissible shaft seal pressure....................... 46
Permissible shaft loads ................................... 47
Order code ...................................................... 47
» Model- Disc valve, roll-gerotor
» Wheel mounting flange
» Side ports
» Shaft- thread hole flange
» SAE and BSPP ports
» Other special features
GENERAL
Max. Displacement,
3
3
801,8 [48.91]
cm /rev [in /rev]
Max. Speed,
736
[RPM]
Max. Torque,
daNm [lb-in]
Max. Output,
kW [HP]
Max. Pressure Drop,
bar [PSI]
Max. Oil Flow,
cont.: 259 [22920]
112 [150]
cont.: 250 [3630]
5
[RPM]
Permissible Shaft Loads,
int.: 350 [5080]
240 [63.4]
lpm [GPM]
Min. Speed,
int.: 340 [30090]
Pa=1500 [3370]
daN [lbs]
Mineral based- HLP(DIN 51524) or HM(ISO 6743/4)
Pressure fluid
O
Temperature range,
-40÷140 [-40÷284]
O
C [ F]
20÷75 [98÷347]
2
Optimal Viscosity range, mm /s [SUS]
ISO code 20/16 (Min. recommended fluid filtration of 25 micron)
Filtration
Pressure Losses
Oil flow in drain line
30
400
flow in
Pressure drop Viscosity Oil
drain line
2
bar [PSI]
mm /s [ SUS] lpm [GPM ]
200 [2 90 0]
2 75 [3990]
20 [98]
2,5 [.660 ]
35 [164]
1,5 [ .400]
20 [98]
4 [1.057]
35 [164]
2,5 [.660]
25
300
200
20
15
10
100
0
5
0
0
25
5
0
44
50
10
15
75
20
100
25
125
30
35
150
40
200 Q, lpm
175
45
50
Q, GPM
MLHV
VMF
MOTORS
SPECIFICATION DATA
Type
Displacement, cm3/rev [in3/rev]
VMF
315
VMF
400
314,5 [19.18] 400,9 [24.5]
VMF
500
VMF
630
VMF
800
499,6 [30.5]
629,1 [38.38]
801,8 [48.91]
Max. Speed,
cont.
636
500
400
315
250
[RPM]
Int.*
736
600
480
380
300
Max. Torque
cont.
115 [10180]
144 [12745]
180 [15930]
227 [20090]
259 [22920]
daNm [lb-in]
Int.*
160 [14160]
200 [17700]
260 [23010]
310 [27440]
340 [30090]
peak**
180 [15930]
230 [20355]
286 [25315]
360 [31860]
402 [35580]
Max. Output
cont.
67 [90]
67 [90]
67 [90]
67 [90]
67 [90]
kW [HP]
int.*
112 [150]
112 [150]
112 [150]
112 [150]
112 [150]
Max. Pressure Drop
cont.
250 [3630]
250 [3630]
250 [3630]
250 [3630]
225 [3263]
bar [PSI]
Int.*
350 [5080]
350 [5080]
350 [5080]
350 [5080]
300 [4350]
peak**
400 [5800]
400 [5800]
400 [5800]
400 [5800]
350 [5080]
Max. Oil Flow
cont.
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
200 [52.8]
lpm [GPM]
Int.*
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
240 [63.4]
Max. Inlet Pressure
cont.
270 [3915]
270 [3915]
270 [3915]
270 [3915]
270 [3915]
bar [PSI]
Int.*
370 [5365]
370 [5365]
370 [5365]
370 [5365]
370 [5365]
peak**
420 [6090]
420 [6090]
420 [6090]
420 [6090]
420 [6090]
140 [2030]
140 [2030]
140 [2030]
140 [2030]
140 [2030]
Max. Return Pressure cont.
with Drain Line
Int.*
175 [2540]
175 [2540]
175 [2540]
175 [2540]
175 [2540]
bar [PSI]
peak**
210 [3045]
210 [3045]
210 [3045]
210 [3045]
210 [3045]
5 [70]
5 [70]
5 [70]
5 [70]
5 [70]
92 [8140]
115 [10180]
144 [12745]
180 [15930]
205 [18145]
10
6
8
6
5
46 [101.4]
47,2 [104,1]
48,5 [106.9]
50 [110.2]]
51,5 [113.5]
Max. Starting Pressure with Unloaded Shaft,
bar [PSI]
Min. Starting Torque daNm [lb-in]
Min. Speed***, [RPM]
Weight, kg [lb]
* Intermittent operation: the permissible values may occur for max. 10% of every minute.
** Peak load: the permissible values may occur for max. 1% of every minute.
*** For speeds lower than given, consult factory or your regional manager.
1. Intermittent speed and intermittent pressure must not occur simultaneously.
2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron or better.
3. Recommend using a premium quality, anti-wear type mineral based hydraulic oil HLP(DIN51524) or HM ( ISO 6743/4).
If using synthetic fluids consult the factory for alternative seal materials.
4. Recommended minimum oil viscosity 13 mm²/s [70 SUS] at 50°C [122°F].
5. Recommended maximum system operating temperature is 82°C [180°F].
6. To assure optimum motor life fill with fluid prior to loading and run at moderate load and speed for 10-15 minutes.
45
MLHV
VMF
MOTORS
DIMENSIONS AND MOUNTING DATA
ø302±0,5
[11.89±.0197]
8xø17,6 +0,2
20
20
0
ø17
[6.6 0
93]
0
ø235
[9.252]
85 -0,5
-0,1
[8.819-.0039
-.0079]
ø224 -0,2
-0,1
ø224 -0,2
[8.819-.0039
-.0079]
ø200 -0,2
[7.874-.0079 ]
[3.346-.0197]
[.693+.0079 ]
65 ]
ø2 433
0.
1
[
20
0
6x
138,5±0,8
[5.453±.032]
60
0
6xM16
max L
L2
6±0,1
[.236±.0039]
16±0,25
[.63±.0098]
5±0,15
50±0,15
50±0,15
Port B
Type
2
4
2xG1
G¼
2x15/ 16 -12UN
9
/ 16 -18UNF
L, mm [in] L1, mm [in] L2, mm [in]
VMF 315 286,5 [11.28] 25,5 [1.00] 109,5 [4.31]
VMF 400 293,5 [11.56] 32,5 [1.28] 116,5 [4.59]
VMF 500 301,5 [11.87] 40,5 [1.59] 124,5 [4.90]
Port A
VMF 630 312,0 [12.28] 51,0 [2.01] 135,0 [5.31]
VMF 800 326,0 [12.83] 65,0 [2.56] 149,0 [5.87]
21±0,15
[.827±.0059]
[.905]
[.197±.0059]
P (A,B)
T
T
L1
23
[1.968±.0059] [1.968±.0059]
ø160 -0,2
[6.299-.0079]
ø160 -0,2
[6.299-.0079]
0
[5.118-.0039
-.0118 ]
-0,1
ø130 -0,3
30
Versions
15±0,15
[.59±.0059]
P(A,B)
5±0,15
[.197±.0059]
Standard Rotation
Viewed from Shaft End
Port A Pressurized - CW
Port B Pressurized - CCW
Warning: Drain line should always be used.
Reverse Rotation
Viewed from Shaft End
Port A Pressurized - CCW
Port B Pressurized - CW
MAX. PERMISSIBLE SHAFT SEAL PRESSURE
P
PSI
1000
800
600
400
P
bar
70
60
50
40
30
20
200
0
10
0
100
200
300
46
400
500
600
700 n, RPM
mm [in]
MLHV
VMF
MOTORS
PERMISSIBLE SHAFT LOADS
Pr
daN
-1
-.5
0
.5
1
1.5
2
2.5
3
3.5
Pr
lbs
4.5 in
4
15000
32000
14000
30000
13000
28000
12000
26000
11000
24000
10000
22000
9000
2
20000
8000
18000
7000
16000
6000
14000
1
5000
12000
10000
4000
0
8000
-20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 mm
1 - Bearing curve: The curve applies to a B10 bearing life of 2000 hours at 100 RPM.
2 - Shaft curve: The curve represents Max. permissible radial shaft load with safety factor 2:1.
ORDER CODE
1
2
3
4
VMF
Pos.1 - Displacement code
315
400
500
630
800
3
3
- 314,5 cm /rev [19.18 in /rev]
- 400,9 cm3/rev [24.45 in3/rev]
- 499,6 cm3/rev [30.48 in3/rev]
- 629,1 cm3/rev [38.38 in3/rev]
- 801,8 cm3/rev [48.91 in3/rev]
Pos.2 - Ports
2
- side ports, 2xG1, G¼, BSP thread, ISO 228
4
- side ports, 2x15 16 -12 UN, O-ring, 9 16 -18 UNF
Pos.3 - Special Features (see page 48)
Pos.4 - Design Series
omit - Factory specified
The hydraulic motors are mangano-phosphatized as standard.
47
MOTOR SPECIAL FEATURES
Motor type
Order
Code
MSWM
MTK
MTM
TMF
MVM
MVMC
VMF
Special
Feature
Description
Speed Sensor*
RS
O
O
O
O
O
-
O
Reinforced motor
HD
-
-
O
O
O
-
O
Low Leakage
LL
O
O
O
O
O
O
O
Low Speed Valving
LSV
O
O
O
O
O
O
O
Free Running
FR
-
O
-
-
-
O
-
Reverse Rotation
R
O
O
O
O
O
O
O
Paint**
P
O
O
O
O
O
O
O
Corrosion
Protected Paint**
PC
O
O
O
O
O
O
O
S
O
O
-
O
O
-
Check Valves
O Optional
- Not applicable
S Standard
* For sensor ordering see pages 49-50.
** Color at customer's request.
For more information about HD option please contact with "M+S Hydraulic".
48
MOTORS WITH SPEED SENSOR
MSWM...RS
MTK...RS
53
[2.086]
max 110
[4.33]
M12x1
max 50
[1.97]
5
9, ]
10 .31
[4
M1
51,9
[2.04]
2
51 o
25
'43
MTM...RS
TMF...RS
80
0
60
[2.36]
max 51,5
[2.03]
57
[2.24]
71
[2.8]
0
M12x1
80
MVM...RS
VMF...RS
M12x1
"
140
[5.51]
49
max 70,5
[2.77]
SPEED
SENSOR
MOTORS
TECHNICAL DATA OF THE SPEED SENSOR
Technical data
Frequency range
Output
Power supply
Current input
Ambient Temperature
Protection
Plug connector
Mounting principle
Output signal
U
0...15 000 Hz
PNP, NPN
10...36 VDC
20 mA (@24 VDC)
-40...+1250C [-40...+2570F]
IP 67
M12-Series
ISO 6149
Uhigh>Ud.c.-2V
Ulow<2V
f1
f2
f
f1=f2±10%
Load max.:Ihigh=Ilow<50mA
Motor type
Pulses per revolution
MSWM
MTK
MTM
TMF
MVM
VMF
54
84
102
Wiring diagrams
PNP
NPN
RLoad [kΩ]=Ud.c. [V]/Imax [mA]
Order Code for Speed Sensor
Stick type
4
1
3
2
Terminal
Cable
Connection Output
No.
Ud.c.
1
Brown
No connection White
2
3
4
0V
Output signal
Sensor Output
Electric connection
Code type
NPN Connector BINDER 713 series
RSN
Blue
Black
PNP
RSP
RSNL5 NPN
Connector BINDER 713 series
RSPL5 PNP
Cable output 3x0,25; 5 m [196 in] long
Cable output 3x0,25; 5 m [196 in] long
NOTE: *- The speed sensor is not fitted at the factory, but is supplied in a plastic bag with the motor.
For installation see enclosed instructions.
50
APPLICATION CALCULATION
VEHICLE DRIVE CALCULATIONS
1.Motor speed: n, RPM
n=
2,65 x vkm x i
Rm
n=
168 x vml x i
Rin
vkm- vehicle speed, km/h;
vml- vehicle speed, mil/h;
Rm- wheel rolling radius, m;
Rin- wheel rolling radius, in;
i- gear ratio between motor and wheels.
If no gearbox, use i=1.
4. Accelerate force: FA, daN [lbs]
Force FA necessary for acceleration from 0 to maximum
speed v and time t can be calculated with a formula:
FA=
vkm x G
3,6 x t
, [daN]
FA=
vml x G
22 x t
, [lbs];
FA- accelerate force, daN [lbs];
t- time, [s].
2.Rolling resistance: RR, daN [lbs]
5.Tractive effort: DP,daN [lbs]
The resistance force resulted in wheels contact with Tractive effort DP is the additional force of trailer. This value
different surfaces:
will be established as follows:
RR=G x r
-acc.to constructor's assessment;
-as calculating forces in items 2, 3 and 4 of trailer; the
calculated sum corresponds to the tractive effort requested.
G- total weight loaded on vehicle, daN [lbs];
r- rolling resistance coefficient (Table 1).
Table 1
Rolling resistance coefficient
In case of rubber tire rolling on different surfaces
Surface
r
Concrete- faultless
0.010
Concrete- good
0.015
Concrete- bad
0.020
Asphalt- faultless
0.012
Asphalt- good
0.017
Asphalt- bad
0.022
Macadam- faultless
0.015
Macadam- good
0.022
Macadam- bad
0.037
Snow- 5 cm
0.025
Snow- 10 cm
0.037
Polluted covering- smooth
0.025
Polluted covering- sandy
0.040
Mud
0.037÷0.150
Sand- Gravel
0.060÷0.150
Sand- loose
0.160÷0.300
3.Grade resistance: GR, daN [lbs]
6.Total tractive effort: TE, daN [lbs]
Total tractive effort TE is total effort necessary for vehicle
motion; that the sum of forces calculated in items from 2 to 5
and increased with 10 % because of air resistance.
TE=1,1x(RR + GR + FA + DP)
RR - force acquired to overcome the rolling resistance;
GR- force acquired to slope upwards;
FA- force acquired to accelerate (acceleration force);
DP- additional tractive effort (trailer).
7.Motor Torque moment: M, daNm [lb-in]
Necessary torque moment for every hydraulic motor:
TE x Rm[Rin]
M=
N x i x hM
N- motor numbers;
hM- mechanical gear efficiency (if it is available).
8.Cohesion between tire and road covering: MW, daNm [lb-in]
MW=
GW x f x Rm[Rin]
i x hM
To avoid wheel slipping, it should be observed the following
condition MW > M
f - frictional factor;
GW- total weight over the wheels, daN [lbs] .
a- gradient negotiation angle (Table 2)
Table 3
Table 2
Frictional factor
f
Grade
%
Degrees
Grade
%
1%
0º 35'
12%
6º 5'
Steel on steel
2%
1º 9'
15%
8º 31'
Rubber tire on polluted surface
0.5 ÷ 0.7
5%
2º 51'
20%
11º 19'
Rubber tire on asphalt
0.8 ÷ 1.0
6%
3º 26'
25%
14º 3'
Rubber tire on concrete
0.8 ÷ 1.0
8%
4º 35'
32%
18º
10%
5º 43'
60%
31º
Surface
Degrees
Rubber tire on grass
51
0.15 ÷ 0.20
0.4
HYDRAULIC
MOTORS
9.Radial motor loading: Prad , daN [lbs]
When motor is used for vehicle motion with wheels
mounted directly on motor shaft, the total radial
loading of motor shaft Prad is a sum of motion force and
weight force acting on one wheel.
GW - Weight held by wheel;
Prad - Total radial loading of motor shaft;
M/R- Motion force.
Prad
GW
M
R
2
Prad= G W +
M
R
In accordance with calculated loadings the suitable motor from the catalogue is selected.
DRAINAGE SPACE AND DRAINAGE PRESSURE
Advantages in oil drainage from drain space: Cleaning; Cooling and Seal lifetime prolonging.
Series connection
Parallel connection
52
2
WARRANTY
M+S Hydraulic warrants, what its products, supplied directly to original equipment
manufacturer, authorized distributor or other customer, will be free of defects in material or
workmanship at the time of shipment from M+S Hydraulic and will conform to the products
technical documentation (drawings and specifications) under sale agreement with Buyer.
This warranty will apply only to defects appearing within applicable Warranty period,
mentioned below. If Buyer notify M+S Hydraulic within the Warranty period about any such
defects, M+S , at its sole option will replace or repair the defective products or their parts
found by M+S Hydraulic to be defective in material or workmanship.
THE FOREGOING LIMITED WARRANTY IS AVAILABLE ONLY IF “M+S HYDRAULIC”
IS PROMPTLY NOTIFIED IN WRITING OF THE ALLEGED DEFECT AND DOES NOT
COVER FAILURE TO FUNCTION CAUSED BY DAMAGE TO THE PRODUCT,
IMPROPER INSTALLATION, UNREASONABLE USE OR ABUSE OF THE PRODUCT,
FAILURE TO PROVIDE OR USE OF IMPROPER MAINTENANCE OR USUAL,
DEGRADATION OF THE PRODUCT DUE TO PHYSICAL ENVIRONMENTS OF AN
USUAL NATURE. THE FOREGOING REMEDIES ARE THE SOLE AND EXCLUSIVE
REMEDIES AVAILABLE TO CUSTOMER. To facilitate the inspection, M+S Hydraulic may
require return of the product/part, which Buyer claims to be defective.
M+S Hydraulic shall not be liable for labor costs or any other expenses incurred during
the disassembling or reinstalling of the product/part.
In case the claimed products are returned to M+S Hydraulic in bad condition: dirty,
disassembled, with damaged or missing parts during transportation, the warranty will be
considered as not applicable and the products will not be liable to repair.
Warranty periods
New products: The Warranty period is limited to 24 consecutive months (2 years) from
the date of production of the product.
Repaired products: If the product is repaired in M+S Hydraulic during its warranty
period, the warranty period of the repaired item shall continue for the balance of original
Warranty period or for a period equal to 50% of the original new product Warranty period,
whichever is later.
Spare parts: The Warranty period for Spare parts shall be 12 consecutive months (1
year) from the dispatch date of such parts from M+S Hydraulic.
LIMITATION OF LIABILITY M+S Hydraulic's liability for any claim of any kind , for any
loss or damage arising out of, connected with or resulting from an order, or from the
performance or branch thereof, or from the design, manufacture, sale delivery, operation
or use of any of its products shall be limited to , at M+S 's sole option, replacement, repair of
any defective product or the issuance of a credit to Customer against any future
purchases. Cash refunds will not be made under any circumstances and Customer will not
be entitled to recover any damages of any kind against M+S Hydraulic, including but not
limited to incidental or consequential damages, whether direct or indirect, known or
unknown, foreseen or unforeseen.