Type: ________________________ Cerra 10 I/D Project: ______________________ Indirect-Direct T8 SCEP Option Suspended S P E C I F I C AT I O N S ________ _______ ________ ________ ________ ________ ________ ________ ________ 10CRM4 ________ ________ ________ ________ ________ _____ ________ ________ _____________________ LAMPING OPTIONS 10CRM4 - 1 10CRM4 - 2 10CRM4 - 3 2 5⁄8” 2 5⁄8” 10” 2 5⁄8” 10” 10” SPECIFICATIONS Construction Nominal 10” x 3” crescent housing is formed from one-piece cold-rolled steel. Flat end plate standard. Sculptured die-cast aluminum end cap is optional. Reflectors Die-formed highly reflective white or specular reflector. fixture wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and C-UL listed. Shielding SSB—Parabolic aluminum baffle with semi specular finish. SBL—Steel straight blade baffle. PPL—Perforated steel straight blade baffle. WPB—Parabolic aluminum baffle with white finish. Luminaire Length 4’, 8’, and 12’ lengths in a single section for nominal suspension spacing of 4’, 8’, and 12’. For total luminaire length, add 1⁄16” for each flat end plate or 4” for each sculptured end cap. Using internal joiners, 4’, 8’, and 12’ sections can be joined to form longer length luminaires. Finish Fine-textured, white or aluminum polyester powder paint. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG CATALOG NUMBER Examples: 10CRM4 2 32 WHR SSB 40FT R12 277 GEB10 DCT LP835 F1/18 C210 SCEP — 10CRM4 3 32 20/80 PPL 32FT R8 277 GEB10 1SE EL DCT LP835 F1/21 C110 _______ ________ Luminaire # of Lamps 10CRM4 in Cross Section _______ __________ __________ _________ _________ __________ _________ __________ Lamp Type Distribution1 Shielding Baffle Ballast Type WHR White Reflector (Standard) SPRSpecular 40/60 40% Up, 60% Down 20/80 20% Up, 80% Down 0/100 0% Up, 100% Down CLI2 Center Lamp Isolator (Blank) No diffuser OPD Standard Brightness Diffuser SSB SBL Maximum Section Length Voltage 32 Luminaire Row Length 120 277 347 GEB10 <10% THD Electronic ADEZ3 Advance Mark 10 dim DMHL3D3 Lutron Hi-Lume dim ADZT3Advance Mark 7 0-10V dim 32W T8 1 2 3 __________ # of Emergency Modules (Blank)None 1SE 1 section 2SE 2 sections XSE X sections Notes: Semi specular White steel blade X FT PPLWhite (4’ increments) perforated steel baffle WPB White Baffle (pre-finished or painted) ________________ _________ ________________ ______________ ______________ Emergency Type4 Switching Lamp Color Mounting Type SCTSingle circuit DCTDual circuit L/LP No lamp L/LPENo lamp. Wired for energy saving lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI F1/ (Blank)None ECEmergency circuit EL3 Emergency battery pack EN3Emergency battery pack w/night light circuit 1 Refer to photometric test for exact distribution 2 Available with 3-lamp cross section only 3 Not available in 347V / T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) F3/ Rigid stem Reference Lamp Chart on website or consult factory for other options. Overall Suspension 1212” 1515” 1818” 2121” 2424” XXXX” Overall suspension is measured from ceiling to bottom of luminaire. 4 EL and EC are installed in last 4’ of luminaire sections. Separate feed required unless ELS or ELS2 is specified R4 R8 R12 4’ section(s) 8’ section(s) 12’ section(s) Reference Ballast Wizard on website or consult factory for other options. ______________ _________________________________ Finish Options C110Painted aluminum (low gloss) C210 White white (fine-textured low gloss) C099 Custom finish ACG BLK Adjustable cable grippers Black cord, cord manager and canopy (not available with F3) CP Chicago plenum (available with F1A only) DL Damp location label DU Dust cover ELH Emergency through wiring w/separate feed ELS Emergency through wiring w/single feed, shared neutral ELS2 Emergency through wiring w/single feed, separate neutrals GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone NYC New York City code OJB Offset junction box SCEP Sculptured end cap SLP Sloped ceiling (for 10-45°, must be specified with F2, ACG and OJB options) XXXX Integrated sensor; choose options and obtain code on page 2 2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com © 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx 10CRM4 Cerra 10 I/D Indirect-Direct T8 1 Cerra 10 I/D Type: ________________________ Project: ______________________ Indirect-Direct T8 Suspended 10CRM4 INTEGRATED NLIGHT MICRO SENSOR Determine the appropriate sensor type, network type and sensor power source for your application. Enter the code in the Options section of the Catalog Number. EXAMPLE: PDT1 Network Type & Sensor Power Source (choose one) Sensor Type (choose one) ADC nLight model nES ADCX Daylight Dimming Specify 0-10V dimming ballast No occupancy sensing PDT nLight model nES PDT7 ADCX Daylight Dimming and/or Occupancy Detection Specify 0-10v dimming ballast for daylight dimming Specify fixed-output ballast for occupancy detection only (daylight dimming disabled) 1* nLight-Enabled (Network-Ready) with Luminaire-Integrated Power Pack 10’ Cat-5e cable and splitter provided 2 Standalone Operation (No Networking) with Luminaire Integrated Power Pack No Cat-5e cable provided 3* nLight-Enabled (Network-Ready) with Remote nLight Power Pack or nPanel 10’ Cat-5e cable and splitter provided Order required remote nLight Power Pack or nPanel separately through nLight (Acuity Brands Controls) For more information about the Integrated nLight Micro Sensor, its capabilities and options, download the PDF guide at: PeerlessLighting.com/nLight-Sensor-Guide *nLight-Enabled (network-ready) options include one RJ-45 connector on the luminaire and 10’ of Cat-5e cable and a splitter to control the entire luminaire row (depending on wattage/voltage limitations). The Cat-5e cable drop is located in the same section as the sensor. For multiple zones, please contact techsupport@peerlesslighting.com. WEIGHTS & SUPPORT SPACING Suspension spacing equals section length. Default location shown. Consult factory for stem mounting suspension spacing and alternate locations. STANDARD SECTIONS Key: • Support or feed location 4’-0 3⁄8” 28 LBS ⁄16” standard flat end plates 4” optional sculptured end plates 1 4’-0 1⁄2” O.A. 8’-0 1⁄8” 48 LBS 8’-0 1⁄4” O.A. 12’-0” 68 LBS 12’-0 1⁄8” O.A. PLAN VIEW CONFIGURATIONS Cast corner and tenon connectors available for suspended configurations. Reference Pattern Connector Guide for additional details. PHOTOMETRICS Actual performance may differ as a result of end-user environment and application. 1-LAMP T8 91.9% efficiency 2619 delivered lumens 2-LAMP T8 91.2% efficiency 5199 delivered lumens 3-LAMP T8 90.7% efficiency 7759 delivered lumens 66.6% up / 33.4% down 62.9% up / 37.1% down 61.9% up / 38.1% down 2-LAMP T8 40/60 DISTRIBUTION 65.4% efficiency 3730 delivered lumens 2-LAMP T8 20/80 DISTRIBUTION 58.5% efficiency 3332 delivered lumens 2-LAMP T8 0/100 DISTRIBUTION 54.9% efficiency 3132 delivered lumens 36.2% up / 63.8% down 18.8% up / 81.2% down 0.9% up / 99.1% down 2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com © 2012 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” and “Cerra” are registered trademarks of Acuity Brands Lighting. Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. 1-year limited warranty. Complete warranty terms located at www.acuitybrands.com/customerresources/terms_and_conditions.aspx 10CRM4 Cerra 10 I/D Indirect-Direct T8 2